NEC Projector SX10000 User Manual

High Light Output Projection System • Großbildschirm Projektions-System  
SX10000  
User’s Manual • Bedienungshandbuch  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions: Please read this manual carefully before using your  
NEC SX10000 Projector and keep the manual handy for future ref-  
erence.  
CAUTION: To turn off the main power, be sure to remove the plug  
from power outlet. The power outlet socket should be installed as  
near to the equipment as possible, and should be easily accessible.  
WARNING  
3. GSGV Acoustic Noise Information Ordinance:  
The sound pressure level is less than 70 dB(A) according to ISO 3744  
or ISO 7779.  
This is a Class A product. In a domestic environment this product may  
cause radio interference in which case the user may be required to take  
adequate measures.  
WARNING  
AVERTISSEMENT  
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE  
THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS  
UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEP-  
TACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE  
FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS  
THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
POUR EVITER UN FEU OU UN RISQUE D’ELECTROCUTION  
NE PAS EXPOSER CET ENSEMBLE A LA PLUIE OU A  
LHUMIDITE;DE MEME, NE PAS BRANCHER LA PRISE POLAIRE  
AVEC UNE RALLONGE A MOINS QUE LES DENTS DE LA PRE-  
MIERE NE S’Y INSERENT PLEINEMENT.  
EVITER D’OUVRIR LE COFFRET CAR IL Y A, A LINTERIEUR,  
DES COMPOSANTS SOUMIS A UNE HAUTE-TENSION; POUR  
LES REPARATIONS, S’ADRESSER A UN PERSONNEL  
QUALIFIE.  
CAUTION  
ATTENTION  
RISK OF ELECTRIC SHOCK  
RISQUE D’ELECTROCUTION  
DO NOT OPEN  
NE PAS OUVRIR  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT  
OPEN COVER. NO USER-SERVICEABLE PARTS IN-  
SIDE. REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
ATTENTION: POUR EVITER LES RISQUES D’ELECTROCUTION, NE  
PAS OUVRIR LE COUVERCLE. AUCUN DES ELEMENTS  
INTERNESNEDOITETREREPAREPARL’UTILISATEUR.  
NE CONFIER L’ENTRETIEN QU’A UN PERSONNEL  
QUALIFIE.  
This symbol warns the user that uninsulated voltage  
within the unit may have sufficient magnitude to cause  
electric shock. Therefore, it is dangerous to make any  
kind of contact with any part inside of this unit.  
L’éclair fléché dans un triangle équilatéral est destiné à  
avertir l’utilisateur de la présence, dans l’appareil, d’une  
zone non-isolée soumise à une haute-tension dont  
l’intensité est suffisante pour constituer un risque  
d’electrocution.  
This symbol alerts the user that important literature  
concerning the operation and maintenance of this unit  
has been included. Therefore, it should be read carefully  
in order to avoid any problems.  
Le point d’exclamation dans un triangle équilatéral est  
destiné à attirer l’attention de l’utilisateur sur la présence  
d’informations de fonctionnement et d’entretien  
importantes dans la brochure dccompagnant l’appareil.  
DOC compliance Notice  
DOC avis de conformation  
This Class A digital apparatus meets all requirements of the  
Canadian Interference-Causing Equipment Regulations.  
Cet appareil numérique de la classe A respecte toutes les exigences  
du Réglement sur le Matériel D’interférence du Canada.  
CAUTION  
* In order to reduce any interference with radio and television reception use a signal cable with ferrite core attached.  
Use of signal cables without a ferrite core attached may cause interference with radio and television reception.  
* This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the installation manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be  
required to correct the interference at his own expense.  
E – ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fire and Shock Precautions  
Important Safeguards  
1. Ensure that there is sufficient ventilation and that vents are unob-  
structed to prevent potentially dangerous concentrations of ozone  
and the build-up of heat inside your projector. Allow at least 8 inches  
(20cm) of space between your projector and a wall. Allow at least 20  
inches (50 cm) of space between the ventilation outlet and object.  
These safety instructions are to ensure the long life of your projector  
and to prevent fire and shock. Please read them carefully and heed all  
warnings.  
Installation  
1. Place the projector on a flat, level surface and in a dry area free from  
dust and moisture.  
2. Prevent foreign objects such as paper clips and bits of paper from  
falling into your projector. Do not attempt to retrieve any objects that  
might fall into your projector. Do not insert any metal objects such as  
a wire or screwdriver into your projector. If something should fall into  
your projector, disconnect it immediately and have the object removed  
by a qualified your service person.  
2. Do not place the projector in direct sunlight, near heaters or heat  
radiating appliances.  
3. Exposure to direct sunlight, smoke or steam could harm internal com-  
ponents.  
3. Do not place any liquids on top of your projector.  
4. Handle your projector carefully. Dropping or jarring your projector could  
damage internal components.  
CAUTION: High Pressure Lamp May Explode if Improperly Handled.  
Refer Servicing to Qualified Service Personnel.  
5. Do not place heavy objects on top of the projector.  
Lamp Caution: Please read before operation  
Due to the lamp being sealed in a pressurized environment, there is  
a small risk of explosion, if not operated correctly. There is minimal  
risk involved, if the unit is in proper working order, but if damaged or  
operated beyond the recommended 750 hours, the risk of explosion  
increases.  
Please note that there is a warning system built in, that displays the  
following message when you reach 750 hours of operationLamp  
Running Time is Over 750 Hours!!When you see this message  
please contact your NEC Dealer for a replacement.  
6. If you wish to have the projector installed on the ceiling:  
a Do not attempt to install the projector yourself.  
b The projector must be installed by qualified technicians in order to ensure  
proper operation and reduce the risk of bodily injury.  
c In addition, the ceiling must be strong enough to support the projector  
and the installation must be in accordance with any local building codes.  
d Please consult your dealer for more information.  
e Do not attempt to stack projectors on the ceiling.  
If the lamp does explode, smoke will be discharged from the vents  
located on the side of the unit. This smoke is comprised of glass in  
particulate form and Xenon gas, and will not cause harm if kept out  
of your eyes. If your eyes have been exposed to this gas, please  
flush your eyes out with water immediately and seek immediate  
medical attention. Do not rub your eyes! This could cause seri-  
ous injury.  
To Dealer or Installer:  
To prevent the projector from falling, install it in a place and fasten it in a  
way with sufficient strength to support the combined weight (107 kg/  
236 lb) of the projector (84 kg/185.3 lb), the lens (10 kg/22 lb) and the  
ceiling mount(13 kg/28.7 lb) for an extended period of time as well as to  
withstand earthquakes.  
Power Supply  
1. The projector is designed to operate on a power supply of 2.8 KW  
AC200-240V 50/60Hz. Ensure that your power supply fits this re-  
quirement before attempting to use your projector.  
WARNING: Do not look into the lens while the projector is on. Seri-  
ous damage to your eyes could result.  
2. Handle the power cable carefully and avoid excessive bending. A  
damaged cord can cause electric shock or fire.  
CAUTION  
Do not unplug the power cable from the wall outlet under any one of  
the following circumstances. Doing so can cause damage to the  
projector:  
3. If the projector will not be used for an extended period of time, dis-  
connect the plug from the power outlet.  
While the message "Please wait a moment" appears. This mes-  
sage will be displayed after the projector is turned off.  
Immediately after the power cable is plugged into the wall outlet  
(the POWER indicator has not changed to a steady orange glow).  
Immediately after the cooling fan stops working (After the projec-  
tor is turned off with the POWER OFF button the cooling fan con-  
tinues to work for 3 minutes while the Two Digit INDICATOR "--"  
flashes).  
4. Placing the power cord and the RGB cable closely to each other can  
cause beat noise. If this happens, keep the two separated so that  
beat noise is not generated.  
Cleaning  
1. Unplug the projector before cleaning.  
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,  
use a mild detergent. Never use strong detergents or solvents such  
as alcohol or thinner.  
3. Use a blower or lens paper to clean the lens, and be careful not to  
scratch or mar the lens.  
E iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Précautions contre l'incendie ou la décharge  
1. S'assurer qu'il y ait une ventilation suffisante et que les ouvertures  
ne soient pas obstruées afin d'éviter des concentrations  
potentiellement dangereuses d'ozone et l'accumulation de chaleur à  
l'intérieur du projecteur. Laisser au moins 20 cm d'espace entre le  
projecteur et un mur. Veuillez laisser un espace libre dau moins 50  
cm (20 pouces) entre les orifices de ventilation et lobjet.  
Recommandations importantes  
Ces instructions de sécurité ont pour but d'assurer une longue vie à  
votre projecteur et d'éviter un incendie ou une décharge électrique. Prière  
de les lire avec attention et de tenir compte de tous les avertissements.  
Installation  
1. Placer le projecteur sur une surface plate et de niveau, et dans un  
endroit sec et à l'abri des poussières et de l'humidité.  
2. Empêcher tous objets étrangers tels que des attaches trombones ou  
des morceaux de papier de tomber à l'intérieur du projecteur. Ne pas  
essayer de récupérer des objets qui seraient tombés dans le  
projecteur. Ne pas introduire d'objets métalliques tels qu'un fil ou un  
tournevis dans le projecteur. Si quelque-chose doit tomber dans le  
projecteur, le débrancher immédiatement et faire enlever l'objet par  
un technicien agréé NEC.  
2. Ne pas exposer le projecteur aux rayons directs du soleil, ni le placer  
près d'un chauffage ou de dispositifs de radiation de chaleur.  
3. L'exposition aux rayons directs du soleil, à la fumée ou à la vapeur  
pourrait endommager des composants internes.  
4. Manipuler le projecteur avec précautions. Laisser tomber le projecteur  
ou lui donner des chocs pourrait endommager des composants in-  
ternes.  
3. Ne pas poser de liquides sur le dessus du projecteur.  
ATTENTION: La lampe à haute pression peut exploser si elle est  
manipulée incorrectement. Confier l'entretien à du personnel  
d'entretien qualifié.  
5. Ne pas poser d'objets lourds sur le dessus du projecteur.  
6. Si vous voulez installer le projecteur au plafond:  
a. Nessayez pas dinstaller le projecteur vous-même.  
b. Le projecteur doit être installé par un technicien qualifié pour garantir une  
installation réussie et réduire le risque d’éventuelles blessures corporelles.  
c. De plus le plafond doit être suffisamment solide pour supporter le projecteur  
et linstallation doit être conforme aux réglementations locales de con-  
struction.  
Précautions avec la lampe : lire avant l'utilisation  
La lampe a été scellée dans un environnement sous pression, et il y  
a donc un petit risque d'explosion, si elle n'est pas utilisée  
correctement. Le risque est minime si l'appareil est en bon ordre de  
marche, mais s'il est endommagé ou utilisé au-delà des 750 heures  
recommandées, le risque d'explosion augmente alors.  
Il est à noter l'existence d'un système d'avertissement intégré, lequel  
affiche le message "Lamp Running Time is Over 750 Hours!! (Le  
temps de fonctionnement de la lampe a dépassé 750 heures !!)"  
lorsque les 750 heures de fonctionnement sont atteintes. Lorsque  
ce message apparaît, prière de contacter son revendeur NEC pour  
un remplacement.  
Si la lampe explose, de la fumée peut être produite par les fentes  
d'aération situées sur le côté de l'appareil. Cette fumée est composée  
de verre sous forme de particules et de gaz de Xenon, et n'est pas  
nuisible si elle est maintenue à distance des yeux. Si les yeux sont  
exposés à ce gaz, les rincer immédiatement à l'eau courante et con-  
sulter tout de suite un médecin. Ne pas frotter les yeux ! Cela  
pourrait provoquer une grave blessure.  
d. Veuillez consulter votre revendeur pour de plus amples informations.  
e. Ne pas superposer les projecteurs accrochés au plafond.  
A l’attention du revendeur ou de l’installateur:  
Afin dempêcher une chute éventuelle du projecteur, veuillez prendre  
en compte lors de son placement et de sa fixation de la force nécessaire  
pour supporter le poids total (107 kg), celui du projecteur (84 kg), de  
lobjectif (10 kg) et de lensemble de fixation au plafond (13 kg), pour de  
longues périodes et de façon à lui permettre de résister aux  
tremblements de terre.  
Alimentation  
1. Le projecteur est conçu pour fonctionner sous une tension  
d'alimentation de 2,8 KW CA 200-240 V 50/60 Hz. S'assurer que la  
tension du secteur soit conforme à ces caractéristiques avant d'utiliser  
le projecteur.  
AVERTISSEMENT:  
Ne pas regarder dans l'objectif lorsque le projecteur est allumé. De  
sérieux dommages aux yeux pourraient en résulter.  
2. Manipuler le cordon d'alimentation avec précautions et éviter des  
flexions excessives. Un cordon endommagé peut occasionner une  
décharge électrique ou un incendie.  
ATTENTION  
Ne pas débrancher le câble dalimentation de la prise du secteur  
dans les circonstances suivantes car cela risque dendommager le  
projecteur:  
3. Si le projecteur ne doit pas être utilisé pendant une longue période,  
débrancher la fiche de la prise de courant.  
Lorsque le message Veuillez patientez un instantapparaît. Ce  
message sera affiché après que le projecteur soit éteint.  
Immédiatement après que le cordon d'alimentation électrique ait  
été branché sur la prise du mur (l'indicateur POWER n'est pas  
encore devenu orange).  
Immédiatement après que le ventilateur de refroidissement de  
soit arrêté de fonctionner. (Après que le projecteur ait été mis  
hors tension à laide du bouton POWER OFF, le ventilateur  
daération continue à tourner durant 3 minutes tandis que le  
INDICATOR à deux chiffres "--" clignote).  
4. Placer le cordon d'alimentation et le câble RGB tout près l'un de  
l'autre peut occasionner un bruit de battement. Si cela se produit, les  
maintenir séparés jusqu'à ce que le bruit de battement disparaisse.  
Nettoyage  
1. Débrancher le projecteur avant de le nettoyer.  
2. Nettoyer régulièrement le boîtier extérieur avec un chiffon humide.  
S'il est très sale, utiliser un détergent doux. Ne jamais utiliser de  
détergent forts ou de solvants tels que de l'alcool ou du diluant.  
3. Utiliser un souffleur ou du papier pour objectif pour nettoyer l'objectif,  
et faire attention de ne pas griffer ou endommager l'objectif.  
E iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY (USA and Canada only)  
NEC Technologies, Inc.(hereafter NECTECH) warrants this product to  
be free from defects in material and workmanship under the following  
terms.  
LIMITATION OF IMPLIED WARRANTIES  
All implied warranties, including warranties of merchantability and fit-  
ness for a particular purpose, are limited in duration to the length of this  
warranty.  
HOW LONG IS THE WARRANTY  
Parts and labor are warranted for (1) OneYear from the date of the first  
customer purchase. The lamp is warranted for 500 hours of operating  
time or 90 days, whichever comes first.  
EXCLUSION OF DAMAGES  
NECTECHs liability for any defective product is limited to the repair or  
replacement of the product at our option. NECTECH shall not be liable  
for:  
Decrease in lamp light output level is not covered by this warranty.  
WHO IS PROTECTED  
This warranty may be enforced only by the first purchaser.  
1. Damage to other property caused by any defects in this product, dam-  
ages based upon inconvenience, loss of use of the product, loss of  
time, commercial loss; or  
WHAT IS COVERED AND WHAT IS NOT COVERED  
Except as specified below, this warranty covers all defects in material  
or workmanship in this product. The following are not covered by the  
warranty:  
2. Any other damages whether incidental, consequential or otherwise.  
Some states do not allow limitation on how long an implied warranty  
lasts and/or do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitations and exclusions may  
not apply to you.  
1. Any product which is not distributed in the U.S.A. or Canada by  
NECTECH or which is not purchased in the U.S.A. or Canada, from  
an authorized NECTECH dealer.  
If you are uncertain as to whether a dealer is authorized, please con-  
tact NECTECH at 800-836-0655.  
HOW STATE LAW RELATES TO THE WARRANTY  
This warranty gives you specific legal rights, and you may also have  
other rights which vary from state to state.  
2. Any product on which the serial number has been defaced, modified  
or removed.  
FOR MORE INFORMATION, TELEPHONE 800-836-0655  
NEC TECHNOLOGIES, INC.  
1250 N. Arlington Heights Road, Suite 500  
Itasca. Illinois 60143-1248  
3. Damage, deterioration or malfunction resulting from:  
a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of  
nature, unauthorized product modification, or failure to follow instructions  
supplied with the product.  
b. Repair or attempted repair by anyone not authorized by NECTECH.  
c. Any shipment of the product (claims must be presented to the carrier).  
d. Removal or installation of the product.  
NOTE: All products returned to NECTECH for service MUST have prior approval.  
To get approval, call NEC Technologies at 800-836-0655.  
e. Any other cause which does not relate to a product defect.  
4. Cartons, batteries, external cabinets, magnetic tapes, or any acces-  
sories used in connection with the product.  
WHAT NEC WILL COVER  
We will pay labor and material expenses for covered items, but we will  
not pay for the following:  
1. Removal or installation charges.  
2. Costs of initial technical adjustments (set-up), including adjustment  
of user controls. These costs are the responsibility of the NECTECH  
dealer from whom the product was purchased.  
3. Payment of shipping charges.  
HOW YOU CAN GET WARRANTY SERVICE  
1. To obtain service on your product, consult the dealer from whom you  
purchased the product, or ship it prepaid to any authorized NECTECH  
service center.  
2. Whenever warranty service is required, the original dated invoice (or  
a copy) must be presented as proof of warranty coverage, and should  
be included in any shipment of the product. Please also include in  
any mailing, your name, address and a description of the problem(s).  
3. For the name of the nearest NECTECH authorized service center,  
call NECTECH at 800-836-0655.  
E v  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Video Adj........................................................................ E-33  
Noise Reduction ...................................................... E-33  
Color Matrix ............................................................. E-34  
Y/C Delay................................................................. E-34  
Telecine ................................................................... E-34  
Motion Select ........................................................... E-34  
Motion Level ............................................................ E-34  
YTR Adjustment ...................................................... E-34  
CTR Adjustment ...................................................... E-34  
Option Adj ...................................................................... E-34  
Clamp Timing........................................................... E-34  
Sync Protection ....................................................... E-34  
VD Delay.................................................................. E-34  
Lens Memory ................................................................. E-35  
Signal Type..................................................................... E-35  
Switcher ......................................................................... E-35  
Gain ......................................................................... E-35  
Volume ..................................................................... E-35  
Ref Adj .................................................................................. E-35  
Keystone ........................................................................ E-35  
Lamp .............................................................................. E-36  
Lamp Mode.............................................................. E-36  
Reference White Balance .............................................. E-36  
Factory Default ..................................................................... E-36  
Projector Options ................................................................. E-36  
Timer .............................................................................. E-36  
On/Off Timer ............................................................ E-36  
Sleep Timer ............................................................. E-37  
Menu .............................................................................. E-37  
Menu Mode/Language/Menu Display Time/  
INTRODUCTION  
Introduction to the SX10000 Projector .................................. E-1  
Getting Started ....................................................................... E-1  
What's in the Box? ................................................................. E-1  
1. PART NAMES AND FUNCTIONS  
Projector ................................................................................. E-2  
Controls............................................................................ E-3  
Terminal Panel ................................................................. E-4  
Remote Control ...................................................................... E-6  
Remote Control Features ................................................ E-6  
Remote Control Precautions ........................................... E-7  
Remote Control Battery Installation ................................ E-7  
2. INSTALLATION  
Setting up Your Projector ....................................................... E-8  
Screen Size and Projection Distance .................................... E-8  
Table of Throw Distance and Image Sizes  
for Optional Lenses ............................................................. E-8  
Lens Shift Adjustable Range ................................................. E-9  
Moving the Projector ............................................................ E-10  
Selecting a Location............................................................. E-10  
3. SETUP  
Connecting the Power Cable and Turning on the Projector..... E-11  
About Startup Screen .......................................................... E-12  
Setting up the Projector ....................................................... E-13  
Keystone ............................................................................... E-14  
Setting up for Double Stacking in Link Mode ...................... E-14  
Projector Orientation ............................................................ E-16  
Display Select/Date Format/Date, Time Preset .... E-37  
Setup .............................................................................. E-38  
Page 1:  
4. CONNECTIONS  
Orientation/Background/S-Video Mode Select. E-38  
Page 2:  
Signal Select(RGB1/2) /Sync Termination  
(RGB 1/2) .......................................................... E-38  
Page 3:  
Signal Select (Video 1/2, S-Video 1/2 and Switcher)E-38  
Page 4:  
When Used in Standalone Operation .................................. E-17  
When Used with One Switcher (ISS-6020/ISS-6020G) ...... E-18  
When Used with Two or More Switchers (100 Inputs) ........ E-19  
REMOTE 1 Connector ......................................................... E-21  
Operating Multiple Projectors with the Remote Control ...... E-23  
Using the RGB DIGITAL Connectors................................... E-24  
Auto Adjust (RGB Only) .................................... E-38  
Power Management/Power Off Confirmation ... E-39  
Keystone Save/Doubler/Last Memory/  
5. OPERATION  
General Controls .................................................................. E-25  
Using the Menus .................................................................. E-25  
Shutter Mechanism .............................................................. E-25  
Customizing Basic/Custom Menu ........................................ E-26  
A List of Direct Key Combinations ....................................... E-27  
Menu Tree ............................................................................. E-28  
Menu Elements .................................................................... E-30  
Menu Descriptions & Functions ........................................... E-31  
Source Select ....................................................................... E-31  
Switcher ......................................................................... E-31  
Entry List ........................................................................ E-31  
Entry Edit Command ............................................... E-31  
Adjust (Source) .................................................................... E-32  
Picture ............................................................................ E-32  
Brightness................................................................ E-32  
Contrast ................................................................... E-32  
Saturation ................................................................ E-32  
Color ........................................................................ E-32  
Hue .......................................................................... E-32  
Sharpness ............................................................... E-32  
V-Aperture ............................................................... E-32  
Gamma Correction .................................................. E-32  
White Balance................................................................ E-32  
Color Temperature ................................................... E-32  
Brightness................................................................ E-32  
Contrast ................................................................... E-32  
Signal Level ............................................................. E-32  
Image ............................................................................. E-32  
Pixel Adjust .............................................................. E-32  
Clock/Phase .......................................................... E-32  
Horizontal/Vertical Position ..................................... E-33  
Aspect Ratio ............................................................ E-33  
Resolution................................................................ E-33  
Overscan ................................................................. E-33  
Video Filter .............................................................. E-33  
Blanking ................................................................... E-33  
Seamless/Lens Memory/User Name................ E-39  
Page 5:  
Communication Speed/Projector ID /  
Default Source Select ........................................... E-39  
Link Mode ...................................................................... E-39  
Switcher Control ............................................................ E-39  
Help ...................................................................................... E-40  
Contents......................................................................... E-40  
Source Information ........................................................ E-40  
Projector Information ..................................................... E-40  
Test Pattern .......................................................................... E-40  
Selecting a new signal that is close to one of the listed  
signals in horizontal and vertical frequency ........................ E-41  
6. SPECIFICATIONS ............................................. E-42  
7. Optional Accessories ...................................... E-44  
XT SDI BOARD/SX HDSDI BOARD .................................... E-44  
REMOTE 3 (XLR) Pin Assignments and Signals ................ E-44  
8. Compatible Input Signal List ........................... E-45  
9. List of Menu Items Available in Link Mode...... E-46  
Appendix ............................................................. E-47  
Dimensions........................................................................... E-47  
Tips on Adjusting Focus for Lens Memory Function ........... E-48  
E vi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
This section introduces you to your new SX10000 Projector, provides a  
list of materials that comes with your projector and describes the fea-  
tures and controls.  
Getting Started  
The fastest way to get started is to take your time and do everything  
right the first time. Taking a few minutes now to review the manual may  
save you hours later on. At the beginning of each section of the manual  
you'll find an overview. If the section doesn't apply, you can skip it.  
Introduction to the SX10000 Projector  
The SX10000 is one of the finest, most technically advanced projectors  
available today.The SX10000 enables you to project exceptionally bright,  
precise images up to 500 inches across (measured diagonally) from  
your PC or Macintosh computer (desktop or notebook), VCR, docu-  
ment camera, laser disc player, DVD player and even an HD VCR or HD  
laser disc player.  
What's In The Box?  
Make sure your box contains everything listed. If any pieces are miss-  
ing, contact your dealer. Please save the original box and packing ma-  
terials if you ever need to ship the projector.  
You can use the projector on a tabletop or cart, you can permanently  
mount it on a ceiling*, or you can use the projector to project images  
from behind the screen. The remote control can be used in a wired or  
wireless configuration.  
SX10000 Projector  
Remote Control with Remote Cable (wireless/wired)  
DVI-D Cable  
Ferrite clamp core for DVI-D cable  
RGB signal cable (15-pin D-Sub)  
Power Cable (single phase)  
Two AA Batteries  
Features you'll enjoy :  
A high-performance 2.0 KW Xenon lamp that delivers 8000 ANSI  
lumens with a lamp life of 750 hours.  
User Manual  
CompactFlash Memory Card (8MB) with Adapter  
NECs unique DLPTM based light engine offers true color reproduc-  
tion.  
The SX10000 can accommodate any picture size from 80 to 500  
inches (measured diagonally).  
The SX10000 projects images with uniform brightness while colors  
remain true to their original source.  
The projector can be double stacked without an external frame, pro-  
ducing bright images of 16,000 ANSI lumens.In addition, double stack-  
ing offers built-in redundancy.  
An image can be projected from in front or behind a screen, and the  
projector can even be installed on the ceiling*.  
Supports RGB digital, HDTV and DVD signals as well as most IBM  
VGA, S-VGA, XGA, SXGA, UXGA (scaling), Macintosh or any other  
RGB signals within a horizontal frequency range or 15 to 107 kHz  
and a vertical frequency range of 24 to 105 Hz. This includes  
NTSC3.58, PAL, PAL60, SECAM, NTSC4.43, Y/C and 1080p, 1080i,  
720p and 480p HDTV standard video signals.  
Built-in telecine detection enables 3:2 pull-down correction with no  
external processing necessary, eliminating jitter and artifacts to allow  
for original film source motion quality.  
A newly designed menu system provides for easy setup and opera-  
tion of the projector.  
The remote control can be used wired or wireless.  
* Installing the projector on the ceiling must be done by authorized  
NEC technicians.  
Consult your NEC dealer for more information.  
Digital Light Processing and DLP are trademarks of Texas Instruments.  
E 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Part Names and Functions  
Projector  
Stacking Pad (4 pcs)  
Ventilation (out)  
Remote Sensor  
PC Card Slot  
Insert a PC memory card  
here to upgrade the  
projector system software  
or copy data. To access  
the slot, loosen the screw.  
AC INPUT  
Connect the supplied power  
cable here (AC 200-240V).  
Foot  
Power Switch (Main power)*  
Input Terminal Panel  
Lens (Optional)  
Carrying Handle  
* To turn on the main power to the projector, press the switch to the ON  
position (I) and the POWER indicator on the rear panel will turn or-  
ange in color.  
Press to the OFF position (0) to turn the main power off.  
NOTE: When turning off the main power, first return the projector to the standby  
condition by pressing the POWER OFF button on the remote control or the POWER  
button on the rear panel and then turn off the main POWER switch. These pro-  
cedures are necessary to protect your projector and the connected equipment.  
Controls  
Carrying Handle  
E 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls  
Remote sensor  
11  
10  
9
8
7
5
4
2
LENS SHIFT  
FOCUS ZOOM MENU  
SELECT  
ENTER  
INDICATOR  
POWER  
ON  
ON/OFF  
-
+
OFF  
STATUS  
CANCEL  
6
3
1
1. Power Button  
6. Cancel Button  
Press to turn the projector on when the projector is in the standby con-  
dition (Main Power switch must be on and the POWER indicator lit or-  
ange). Press and hold for 2 seconds to turn off the projector.  
Press this button to exit the menu. Press this button to return the adjust-  
ments to the last condition while you are in the adjustment or setting  
menu.  
2. Power Indicator  
7. Select (Up/Down/Left/Right) Button  
When this indicator is green, the projector is on; when the indicator is  
Up/Down: Use these buttons to select the menu of the item you wish to  
orange, it is in standby mode.  
adjust.  
Left/Right: Use these buttons to change the level of a selected menu  
item.  
NOTE: After the projector is turned off, the indicator "--" flashes for three min-  
utes to show that the cooling fan is working.  
Do not turn off the main power during that time. After "--" stops flashing, the  
POWER indicator will change to a steady orange glow and the projector will be  
in the stand-by mode.  
8. Menu Button  
Displays the main menu for operation.  
9. Zoom Button  
Zoom the lens in and out.  
3. Status Indicator  
When the On Timer is set and the projector is in the standby mode, the  
Status indicator flashes green to show that the On Timer program is  
active.  
10. Focus Button  
Adjust the lens focus.  
4. Two Digit Display  
11. Lens Shift Button  
Adjust the lens offset by shifting the projected image position horizon-  
tally and vertically.  
During normal operation the current projector ID (address) is shown in  
this two digit display. In the event of an error, a projector error code will  
be displayed.The display can be turned off using the ON/OFF Switch to  
the left of the display.  
5. Enter Button  
Executes your menu selection and activates items selected from the  
menu. When the slidebar or dialog box is displayed:  
Pressing this button confirms adjustments/setting and returns to the  
previous menu display.  
E 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Terminal Panel  
5
RGB DIGITAL  
OUTPUT  
INPUT9  
6
7
INPUT3  
RGB  
INPUT2  
R/Cr  
INPUT1  
R/Cr  
INPUT4  
Cr  
1
2
3
OUTPUT  
G/Y  
B/Cb  
H/HV  
V
G/Y  
Y
OPTION  
IN  
Cb  
SDI  
B/Cb  
H/HV  
V
Space to install the optional XT SDI or SX HDSDI board.  
OUT  
INPUT0  
REMOTE1  
8
S-VIDEO1 INPUT5  
INPUT6  
VIDEO2  
9
REMOTE2  
IN  
Y
VIDEO1  
C
4
OUT  
S-VIDEO2  
10  
INPUT7  
IN  
INPUT8  
REMOTE3  
OUT  
11  
12  
LED  
ON  
OFF  
13  
E 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. INPUT 3 RGB Connector (Mini D-Sub 15 pin)  
Connect your PC or other analog RGB equipment such as a high-defi-  
nition document camera.  
7. INPUT 4 Y/Cb/Cr Terminal (RCA)  
Connect component video outputs (Y/Cb/Cr, Y/Pb/Pr) of the external  
equipment such as DVD player.  
This connector accepts RGB signals only.  
Not compatible with component signals.  
NOTE: This terminal accepts component signals only.  
8. INPUT 5 VIDEO 1 Terminal (BNC)  
Connect to the BNC video output of the external equipment such as a  
VCR or laser disc player.  
2. Option Connector (Mini D-Sub 9 pin)  
For system expansion such as PC-control.  
IN ................. connect to the external equipment such as PC or Third Party  
Control System.  
OUT ............. for daisy-chaining multiple projectors and operating them with  
the same external equipment. To do so, connect to a second  
projector's IN terminal to relay the input at the IN terminal of  
the first projector until all the projectors are connected.  
9. INPUT 6 VIDEO 2 Terminal (RCA)  
Connect to the RCA video output of the external equipment such as a  
VCR or laser disc player.  
10. INPUT 8 S-VIDEO 2 Terminal (Mini DIN 4 pin)  
Connect to the S-video output of the external equipment such as a  
VCR with an S-video output.This terminal allows switching between S2  
and S1 VIDEO input modes. See the "S-Video Mode Select" section on  
page E-38 for more information.  
3. REMOTE 1 Connector (Mini D-Sub 15 pin)  
This terminal allows external control of the projector from either the  
Switcher or from an external control. When the Switcher is used, con-  
nect to the REMOTE 1 terminal on the back of the Switcher.  
NOTE: This projector is compatible with the ISS-6020 Switcher.  
11. INPUT 7 S-VIDEO 1 Terminal (BNC)  
Connect to the Y/C separate BNC video outputs of the external equip-  
4. REMOTE 2 Jacks  
ment such as a VCR or laser disc player.  
IN ................. wired remote control input.  
OUT ............. for daisy-chaining multiple projectors and operating them with  
the same remote control. To do so, connect to a second pro-  
jector' s IN terminal to relay the input at the IN terminal of the  
first projector until all the projectors are connected.  
12. LED Switch  
Lights up the panel on both the front and the rear at the same time.  
13. REMOTE3 Connectors (XLR Connectors)  
Connect an extension cable such as an audio cable to control two pro-  
jectors or more using the remote control. See page E-43 for the pin  
assignments.  
5. RGB Digital Input/Output Connectors (DVI-D 24 pin)  
These connectors are used for double stacking.  
Use the supplied DVI-D cable to connect the OUTPUT terminal of the  
first projector to the second projector's INPUT until all the projectors  
are connected.  
IN ................. wired remote control input.  
OUT ............. for daisy-chaining multiple projectors and operating them with  
the same remote control. To do so, connect to a second pro-  
jector's IN terminal to relay the input at the IN terminal of the  
first projector until all the projectors are connected.  
The output is TMDS non-perfect.  
The output connector is used for stacking.  
6. INPUT 1 and INPUT 2 Terminals (BNC)  
Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of the  
external equipment such as the Switcher. If using a component with a  
combined sync (SYNC) output, connect it to the H/V terminal.  
Also connect component video outputs (Y/Cb/Cr) of the external equip-  
ment such as DVD player.  
NOTE: The INPUT 2 terminal does not support SW1 Level and SW2 Level modes  
for the ISS-6020 switcher.  
E 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7 ADJUST PICTURE  
Remote Control  
Press to display the Picture adjustment screen. Pressing this button  
sequentially selects "Brightness" "Contrast" "Saturation" "Color"  
"Hue" "Sharpness" "V-Aperture" "Gamma Correction".  
Remote Control Features  
27  
8 IMAGE/PROJECTOR  
Press to display the Image Option screen. Pressing this button sequen-  
tially selects "Pixel Adjust" "Position" "Aspect Ratio" "Resolu-  
tion" "Overscan" "Video Filter" "Blanking".  
While pressing and holding CTL, pressing this button rotates "On/Off  
Timer" "Sleep Timer" "Menu" "Setup" "Link Mode" →  
"Switcher Control".  
2
POWER  
INPUT  
ON  
OFF  
1
4
7
ABC  
JKL  
2
DEF  
3
6
9
GHI  
PQR  
YZ/  
1
TEST  
5MNO  
13  
28  
8
9 INPUT  
9
IMAGE/ PROJECTOR  
STU  
8
0
VWX  
Use to select an input, to name a signal, or to enter a passcode during  
input registration.  
ON  
PICTURE WHITE BAL.  
ADJUST  
OFF  
1--INPUT 1 for RGBHV/Y, Cb/Pb, Cr/Pr  
2--INPUT 2 for RGBHV/Y, Cb/Pb, Cr/Pr  
3--INPUT 3 for RGB  
4--INPUT 4 for Y, Cb/Pb, Cr/Pr  
5--INPUT 5 for VIDEO 1  
6--INPUT 6 for VIDEO 2  
7--INPUT 7 for S-VIDEO 1  
8--INPUT 8 for S-VIDEO 2  
9--INPUT 9 for RGB DIGITAL input  
0--INPUT 0 for SDI input on the optional SDI board  
7
6
22  
21  
23  
14  
KEY ST./  
R
AMP  
/
G
E-LIST/  
B
HELP  
INFO  
OSD  
12  
PIXEL POSI/ LENS PICT/ SHUT SOUND  
15  
17  
16  
19  
18  
20  
MUTE  
AUTO  
MENU/ ADDRESS  
10 UNDO  
3
5
4
Press to return the adjustments and settings to the previous condition.  
While pressing and holding CTL, pressing this button clears all the menus  
or adjustment/setting screen. At this time the adjustments/settings are  
stored in memory.  
UNDO  
ENTER  
10  
11  
CANCEL  
FOCUS  
+
ZOOM  
+
MAGNIFY/  
11 CANCEL  
Press to exit the menu.  
CTL  
-
-
25  
24  
Press this button with CTL to return to the previous menu while the  
menus appear. This feature allows you to adjust several items concur-  
rently.  
26  
12 INFO  
Displays the "Source Information" or "Projector Information" window.  
This button toggles between these two windows.  
13 TEST  
Press to display the test pattern. Pressing this button sequentially se-  
lects five test patterns.  
1 POWER ON  
Press to turn on the projector. The POWER indicator lights up green.  
14 HELP  
Provides online help.  
2 POWER OFF  
Press and hold this button for a minimum of two seconds to turn off the  
projector.  
15 PIXEL  
Displays the Pixel Adjust screen to adjust the clock and phase.  
3 MENU  
Press to display the main menu.  
16 AUTO (RGB only)  
While pressing and holding CTL, press this button to display the Re-  
mote Control ID dialog box to specify the remote control ID.  
Press to adjust Position-H/V and Pixel Clock for an optimal picture.  
NOTE: The Pixel Phase is not available.  
4 ENTER  
17 POSITION  
Executes the menu selection and activates items selected from the menu.  
When the slidebar or dialog box is displayed:  
Pressing this button confirms adjustments/setting and returns to the  
previous menu display.  
Press to display the Blanking screen; press again to display the Posi-  
tion screen.  
While pressing and holding CTL, pressing this button displays the Lens  
Shift adjustment screen.  
5 SELECT (Up/Down/Left/Right)  
When pressed together, the CTL and buttons work as a Back Space  
key in the entry screen.  
Pressing and holding CTL, then this button moves the menu, slidebar  
or dialog box.  
18 MUTE SOUND  
(available only when using with the ISS -6020 or IPS4000)  
Turns off the sound for a short period of time. Press again to restore the  
sound.  
6 ADJUST WHITE BAL  
Press to display the Color adjustment screen. Pressing this button se-  
quentially selects "Color Temperature" "White Balance - Brightness"  
"White Balance - Contrast" "Signal Level" "Ref.White Bal" →  
"Switcher-Gain".  
E 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19 MUTE OSD  
Remote Control Precautions  
Press to turn off the on-screen display. Press again to restore the on-  
screen display.  
Use the remote control within a distance of about 7m (23feet) and at  
an angle of 30˚ above, below, to the left and to the right of the remote  
control sensor located at the front of the main unit.  
The remote control system may not function when direct sunlight or  
strong illumination strikes the remote control sensor of the main unit,  
or when there is an obstacle in the path.  
NOTE: You can also turn off the on-screen display by pressing and holding CTL  
and then pressing MUTE OSD; doing this again restores it. In this case any  
adjustment will still change the projector's memory settings. This mode is avail-  
able even when an input is switched to another or the power is turned off using  
the POWER OFF button on the remote control.  
When remote control buttons are pressed and held, main unit func-  
tion keys may not operate.  
20 MUTE PICTURE  
Do not subject to strong shock.  
Press to turn off the picture for a short period of time. Press again to  
restore the picture. Pressing and holding CTL, then pressing this button  
shuts off the light completely.  
Do not allow water or other liquid to splash on the remote control. If  
the remote control gets wet, wipe it dry immediately.  
Avoid exposure to heat and steam.  
Remove the batteries from the remote control when the remote con-  
trol is not going to be used for a long period.  
NOTE: This is also considered the LENS SHUTTER.  
21 KEYSTONE (R)  
Press to display the Keystone Correction screen.  
You cannot operate the projector using the remote control if:  
the remote ID is not set to [00].  
the remote ID is not the same as the projector ID.  
See page E-23 for setting remote ID and page E-39 for setting pro-  
jector ID.  
22 AMPLITUDE (G)  
Service personnel only.  
23 ENTRY LIST (B)  
Press to display the Entry List screen.  
Remote Control Battery Installation  
Installing the Remote Control Batteries  
When it comes time to replace the batteries, two "AA" type will be re-  
quired.  
24 FOCUS (+/)  
While pressing and holding CTL, pressing this button allows you to ad-  
just the lens focus.  
1. Press and open the cover.  
25 MAGNIFY/ZOOM (+/)  
Magnify the size of a target portion.  
While pressing and holding CTL, pressing this button allows you to zoom  
the lens in and out.  
26 CTL  
Used in conjunction with other buttons, similar to a shift key on a com-  
puter.  
A D D R E S S  
M E N U /  
I N F O  
S O U N D  
S H U T  
U N D O  
H E L P  
B
P I C T /  
L E N S  
A U T O  
E - L I S T /  
P O S I /  
/
G
/
Y Z 9  
0
P I X E L  
A M P  
R
X
. /  
P Q R  
6
V W  
8
K E Y S T  
A D J U S T  
N O M 5  
S T 7 U  
G H I  
3
W H I T E B A L .  
D E F  
2
I N P U T  
J K L  
4
P I C T U R E  
2. Align and insert the batteries according to the (+) and (-) indications  
inside the case.  
P R O J E C T O R  
I M A G E /  
F F  
A B C  
1
O
O N  
O F F  
T E S T  
O N  
P O W E R  
28  
29  
27  
27 Remote Jack  
Connect your remote control cable here for wired operation.  
28 Backlight Switch  
When using the remote control wirelessly:  
3. Replace the cover.  
Turns the backlight on and off. If no button operation is made within 30  
seconds with the Backlight ON, the Backlight will turn off to conserve  
battery life.  
When using as the wired remote control:  
The light stays on in standby and power-on.  
29 Infrared Transmitter  
Direct the remote control toward the remote sensor on the projector  
cabinet.  
E 7  
Download from Www.Somanuals.com. All Manuals Search And Download.