NEC Projector LT240K User Manual

CD-ROM version

Portable Projector

LT260K/LT240K

User’s Manual

About this user's manual

The fastest way to get started is to take your time and do every-

thing right the first time. Take a few minutes now to review the

user's manual. This may save you time later on. At the begin-

ning of each section of the manual you'll find an overview. If the

section doesn't apply, you can skip it.

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Introduction to the Projector

• Safety protect by Password and Security functions

Password and Security features prevent the projector from being used

by unauthorized individuals.

Password prevents unauthorized individuals from changing projector

settings or adjustments. Security offers complete protection by using

your PC card as a protect key so that the projector will not project a

signal without insertion of the registered PC card and unauthorized

use can be discouraged.

• The built-in Viewer allows you to start your presentation even when a

PC is not available at the site.

• A high-bright 220 watt DC lamp.

• The Standby mode reduces standby power consumption significantly.

• The supplied wireless remote control that operates the projector from

the front side or rear.

• The image can be projected between 30 and 500 inches (measured

diagonally).

• The "Capture" enables you to capture the current projected image.

• An image can be projected from in front or behind a screen, and the

projector can even be installed on the ceiling.

• NEC’s exclusive Advanced AccuBlend intelligent pixel blending tech-

nology - an extremely accurate image compression technology - of-

fers a crisp image with UXGA (1600

1200) resolution*³.

• Supports most IBMVGA, SVGA, XGA , SXGA/UXGA(with Advanced

AccuBlend)*³, Macintosh, component signal (YCbCr/ YPbPr) or any

other RGB signals within a horizontal frequency range of 24 to 100

kHz and a vertical frequency range of 50 to 120 Hz. This includes

NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 stan-

dard video signals.

A UXGA (1600

1200) and SXGA image (1280

1024) are displayed

with NEC’s Advanced AccuBlend on LT260K/LT240K.

E-3

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Introduction to the Projector

NOTE: Composite video standards are as follows:

NTSC: U.S. TV standard for video in U.S. and Canada.

PAL: TV standard used in Western Europe.

PAL-N: TV standard used in Argentine, Paraguay and Uruguay.

PAL-M: TV standard used in Brazil.

PAL60: TV standard used for NTSC playback on PAL TVs.

SECAM: TV standard used in France and Eastern Europe.

NTSC4.43: TV standard used in Middle East countries.

E-4

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Introduction to the Projector

• The supplied remote control can be used without a cable, and you

can even use the remote control to operate your PC's mouse wirelessly

from across the room with the built-in remote mouse function.

• You can control the projector with a PC using the PC Control port.

• USB port allows USB mouse operation*⁴.

The USB ports meet the USB1.1 specification.

• The contemporary cabinet design is light, compact, easy to carry,

and complements any office, boardroom or auditorium.

• Nine pointers are available for your presentation.

E-5

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Projector

Part Names of the Projector

Focus Ring

(See page E-43)

Remote Sensor

(See page E-20)

Controls

(See page E-8)

P O W E R

S T A T U S

L A M P

E C N

- C

Ventilation (inlet)

Ventilation (outlet)

Heated air is exhausted

from here

Built-in Security Slot

(

Zoom Lever

(See page E-43)

Adjustable Tilt Foot Lever

(See page E-42)

Carrying Handle

Lens

Lens Cap

Adjustable Tilt Foot

(See page E-42)

This security slot supports the MicroSaver^®Security System.

MicroSaver^®is a registered trademark of Kensington Microware Inc.

The logo is trademarked and owned by Kensington Microware Inc.

E-6

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Projector

PC Card Eject Button

Monaural Speaker (2W)

PC Card Slot

Lamp cover

(See page E-121)

Ventilation

(outlet)

Remote Sensor

(See page E-20)

Lamp cover screw

Rear Foot

Rotate to make the projector level.

(See page E-43)

Main Power Switch

AC Input

When you plug the supplied power cable into an ac-

tive wall outlet and turn on the Main Power switch,

the POWER indicator turns orange and the projector

is in standby mode.

Connect the supplied power cable's three-pin

plug here, and plug the other end into an active

wall outlet.

(See page E-35)

(See page E-36)

E-7

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Projector

Top Features

1.POWER Button (ON / STAND BY)

Use this button to turn the power on and off when the main power is

supplied and the projector is in standby mode.

NOTE: To turn on or off the projector, press and hold this button for a mini-

mum of two seconds.

2. STATUS Indicator

If this light blinks red rapidly, it indicates that an error has occurred, the

lamp cover is not attached properly or the projector has overheated. If

this light remains orange, it indicates that you have pressed a cabinet

key while the Control Panel Key Lock is enabled. See the Status Indi-

cator section on page E-126 for more details.

3. POWER Indicator (

)

When this indicator is green, the projector is on; when this indicator is

orange, it is in standby or idle mode. See the Power Indicator section

on page E-126 for more details.

E-8

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Projector Ͼ Top Features

4. SOURCE Button

Use this button to select a video source such as a PC, VCR, DVD

player, Viewer (PC card), or LAN.

Press and release this button quickly to display the Source List.

Each time this button is pressed for a minimum of ONE second, the

input source will change as follows:

RGB1 → RGB2 → Video → S-Video → Viewer → RGB1 → ...

If no input signal is present, the input will be skipped.

5. AUTO ADJUST Button

Use this button to adjust Position-H/V and Pixel Clock/Phase for an

optimal picture. Some signals may not be displayed correctly or take

time to switch between sources.

6. PC CARD Access Indicator

Lights while accessing a PC card.

7. ENTER Button

Executes your menu selection and activates items selected from the

menu.

8. CANCEL Button

Press this button to exit "Menus". Press this button to return the adjust-

ments to the last condition while you are in the adjustment or setting

menu.

9. SELECT ̆̄̇̈ (+) (–) / Volume Buttons

̆̄ : Use these buttons to select the menu of the item you wish to

adjust.When no menus appear, these buttons work as a volume

control.

E-9

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Projector Ͼ Top Features

̇̈ : Use these buttons to change the level of a selected menu item.

A press of the ̈ button executes the selection.When the menus

or the Viewer tool bar is not displayed, these buttons can be

used to select a slide, or to move the cursor in Folder List or

Slide List.

When the pointer is displayed, these ̆̄̇̈ buttons move the pointer.

10. MENU Button

Displays the menu.

11. LAMP Indicator

If this light blinks red rapidly, it's warning you that the projection lamp

has exceeded 2000 hours (up to 3000 hours in Eco mode) of service.

After this light appears, replace the lamp as soon as possible. (See

page E-121). If this is lit green continually, it indicates that the lamp

mode is set to Eco. See the Lamp Indicator section on page E-127 for

more details.

12. 3D REFORM Button

Press this button to enter 3D Reform mode to correct the keystone

(trapezoidal) distortion, and make the image square.

E-10

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Projector Ͼ Terminal Panel Features

Terminal Panel Features

12 9 10 11 3 5

1. RGB IN 1 / Component Input Connector (Mini D-Sub 15 Pin)

Connect your computer or other analog RGB equipment such as IBM

compatible or Macintosh computers. Use the supplied RGB cable to

connect to your computer.This also serves as a component input con-

nector that allows you to connect a component video output of compo-

nent equipment such as a DVD player. This connector also supports

SCART output signal. See page E-28 for more details.

2. RGB IN 2 / Component Input Connector (Mini D-Sub 15 Pin)

This connector has the same function as the RGB IN 1 connector.

NOTE: The RGB IN 2 does not support SCART output signal and Plug &

Play.

3. RGB AUDIO IN Mini Jack (Stereo Mini)

This is where you connect audio output from your computer or DVD

player. A commercially available audio cable is required.

4. RGB OUT Connector (Mini D-Sub 15 Pin)

You can use this connector to loop your computer image to an external

monitor from the RGB 1 or 2 input source.

The RGB analog signal set on RGBOUT Terminal is output during idle

mode. See pages E-31 and 100.

E-11

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Projector Ͼ Terminal Panel Features

5. AUDIO OUT Mini Jack (Stereo Mini)

Connect an additional audio equipment here to listen to audio coming

from your computer, Video or S- Video input.

Note that there is no audio output from this jack during Standby and

Idle.

6 S-VIDEO IN Connector (Mini DIN 4 Pin)

Here is where you connect the S-Video input from an external source

like a VCR.

NOTE: S-Video provides more vivid color and higher resolution than the tra-

ditional composite video format.

7. VIDEO IN Connector (RCA)

Connect a VCR, DVD player, laser disc player, or document camera

here to project video.

8. VIDEO AUDIO IN Jacks (RCA)

L : This is your left channel audio input for stereo sound coming from

the VIDEO source.

R : This is your right channel audio input for stereo sound from the

VIDEO source.

9. PC CONTROL Port (Mini DIN 8 Pin)

Use this port to connect your PC to control your projector via a serial

cable. This enables you to use your PC and serial communication pro-

tocol to control the projector.The NEC optional serial cable (CA03D) is

required to use this port. You can also control the projector by using

Dynamic Image Utility 2.0 included on the supplied CD-ROM.

To do so you must first have Dynamic Image Utility 2.0 installed on your

PC. If you are writing your own program, typical PC control codes are

on page E-136. A cap is put on the port at the factory. Remove the cap

when using the port.

E-12

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Projector Ͼ Terminal Panel Features

10. USB Port (Type A)

Connect a commercially available mouse that supports USB.You can

operate the menu or Viewer with the USB mouse via this port.

Note that this port should not be connected to a computer and that

there may be some brands of USB mouse that the projector does not

support.

11. USB Port (Type B)

Connect this port to the USB port (type A) of your PC using the sup-

plied USB cable. You can operate your computer's mouse functions

from the remote control.

12. PC CARD Eject Button

Press to eject a PC card partially.

13. PC CARD Slot

Insert a PC card, commercially available LAN card or NEC optional

wireless LAN card here.

E-13

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Remote Control

Part Names of the Remote Control

NOTE: If you are using a Macintosh com-

puter, you can click either the right-click

or left-click button to activate the mouse.

S L I D E

I E

O R M

3 D

I N T E R

P O

S P E C T

P J

S E L E C T

L A S E R

R G B 2

1. Infrared Transmitter

R G B 1

O N

A U T O A D J .

S - V I D E O

P O W E R

V I D E O

Direct the remote control toward

the remote sensor on the projector

cabinet.

O F F

2. LASER Pointer

Beams a laser light when the LA-

SER button is pressed.

OFF

POWER

S-VIDEO RGB1

3. LED

VIDEO

RGB2

Flashes when any button is

pressed.

AUTO ADJ.

LASER

4. POWER ON Button

SELECT

If the main power is applied, you

can use this button to turn your pro-

jector on.

NOTE: To turn on the projector, press

and hold the POWER ON button for a

minimum of two seconds.

ASPECT FREEZE 3D REFORM

HELP

POINTER VIEWER

SLIDE

VOLUME MAGNIFY

5. POWER OFF Button

You can use this button to turn your

projector off.

PICTURE

FOLDER

SLIDE

PIC-MUTE

LIST

NOTE: To turn off the projector, press

and hold the POWER OFF button for

a minimum of two seconds.

E-14

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Remote Control

6. VIDEO Button

Press this button to select an NTSC, PAL, PAL-N, PAL-M, PAL60,

SECAM or NTSC4.43 compatible video source from aVCR, DVD player,

or laser disc player.

7. S-VIDEO Button

Press this button to select an S-Video source from a VCR.

8. RGB 1 Button

Press this button to select a video source from computer or component

equipment connected to your RGB IN 1 port.

9. RGB 2 Button

Press this button to select a video source from computer or component

equipment connected to your RGB IN 2 port.

10. AUTO ADJ Button

Use this button to adjust an RGB source for an optimal picture. Some

signals may not be displayed correctly or take time to be displayed.

See page E-47.

11. LASER Button

Press and hold this button to activate the laser pointer. When lit, you

can use the laser to draw your audience's attention to a red dot that

you can place on any object.

12. MENU Button

Displays the menu for various settings and adjustments.

E-15

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Remote Control

13. SELECT ̆̄̇̈ (Mouse) Button

When you are in the Computer mode, these buttons work as a com-

puter mouse. When you are in the Projector mode, which is indicated

by lighting the PJ button. See page E-52.

̆̄ : Use these buttons to select the menu of the item you wish to

adjust.

̇̈ : Use these buttons to change the level of a selected menu item.

A press of the ̈ button executes the selection.

When the pointer is displayed, these ̆̄̇̈ buttons move the pointer.

When the pointer is not displayed, these ̆̄̇̈ buttons are for adjust-

ing the image.

14. ENTER (Left Click) Button

When you are in the Computer mode, this button works as the mouse

left button. When this button is pressed and held for a minimum of 2

seconds, the drag mode is set. When you are in the Projector mode,

which is indicated by lighting the PJ button:

Use this button to enter your menu selection. It works the same way as

the ENTER button on the cabinet. See page E-9.

15. CANCEL (Right Click) Button

When you are in the Computer mode, this button works as the mouse

right button.When you are in the Projector mode, which is indicated by

lighting the PJ button: Press this button to exit the Menus. It works the

same way as the CANCEL button on the cabinet.

16. PJ Button

Press this button to switch the SELECT, CANCEL, and ENTER but-

tons between the Projector mode (lit red) and the Computer mode.

Press this button or any one of the POWER ON/OFF, MENU, ASPECT,

3D REFORM, HELP, POINTER, MAGNIFY, PICTURE, VIEWER,

FOLDER LIST or SLIDE LIST buttons to switch to the Projector mode

and the PJ button lights red. To switch back to the Computer mode,

press the PJ button again. See page E-52.

E-16

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Remote Control

17. ASPECT Button

Press this button to display the Aspect Ratio select screen. See page

E-86.

18. FREEZE Button

This button will freeze a picture. Press again to resume motion.

19. 3D REFORM Button

Press this button to enter 3D Reform to correct the keystone (trapezoi-

dal) distortion, and make the image square. See page E-44.

20. HELP Button

Provides the online help or the set information.

21. POINTER Button

Press this button to display one of the eight pointers; press again to

hide the pointer.You can move your pointer icon to the area you want

on the screen using the Select ̆̄̇̈ button. See page E-54.

22. VOLUME (+) (–) Button

Press (+) to increase the volume and (–) to decrease it.

23. MAGNIFY (+) (–) Button

Use this button to adjust the image size up to 400%. When the pointer

is displayed, the image is magnified about the center of the pointer.

When the pointer is not displayed, the image is magnified about the

center of the screen. When the image is magnified, the pointer is

changed to the magnifying icon. See page E-55.

24. PICTURE Button

Press this button to display the Picture adjustement screen such as

Brightness, Contrast, Color, Hue, and Sharpness. See page E-85.

E-17

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Remote Control

25. PICTURE MUTE Button

This button turns off the image and sound for a short period of time.

Press again to restore the image and sound.

NOTE: When the menu is displayed, a press of this button mutes an image and

sound without turning off the menu.

26. VIEWER Button

Press this button to select the Viewer source.

27. SLIDE (+) (–) Button

Press (+) to select the next folder or slide and (–) to select the previous

folder or slide. See page E-67.

28. FOLDER LIST Button

Press this button to select Viewer source to display a list of folders

included in a PC card. See page E-67.

29. SLIDE LIST Button

Press this button to select Viewer source to display a list of slides in-

cluded in a PC card. See page E-67.

NOTE: The default is the Computer mode, which allows you to use the SE-

LECT, CANCEL, and ENTER buttons as your computer mouse. When the

POWER ON/OFF, MENU, ASPECT, 3D REFORM, HELP, POINTER, MAG-

NIFY, PICTURE, VIEWER, FOLDER LIST, or SLIDE LIST button is pressed,

the PJ button lights red to indicate that you are in the Projector mode. If no

buttons are pressed within 60 seconds, the light goes out and the Projector

mode is canceled.

E-18

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Remote Control

Battery Installation

1. Press the catch and remove the battery cover.

2. Remove both old batteries and install new ones (AA). Ensure that you

have the batteries' polarity (+/-) aligned correctly.

3. Slip the cover back over the batteries until it snaps into place. Do not mix

different types of batteries or new and old batteries.

Note on Remote Control Operation:

If you press and hold the SELECT ̆̄̇̈ button while installing new

batteries, the remote control may fail to work properly.

Should this happen, remove the batteries and then install them again with-

out touching the SELECT button.

E-19

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION Ͼ Part Names of the Remote Control

Remote Control Precautions

• Handle the remote control carefully.

• If the remote control gets wet, wipe it dry immediately.

• Avoid excessive heat and humidity.

• If you will not be using the remote control for a long time, remove the

batteries.

• Do not place the batteries upside down.

• Do not use new and old batteries together, or use different types of

batteries together

Operating Range

7m/22 feet

Remote control

Remote sensor on the

projector cabinet

• The infrared signal operates by line-of-sight up to a distance of about

22 feet/7 m and within a 60-degree angle of the remote sensor on the

projector cabinet.

• The projector will not respond if there are objects between the re-

mote control and the sensor, or if strong light falls on the sensor.

Weak batteries will also prevent the remote control from properly

operating the projector.

E-20

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS

This section describes how to set up your projector and how to connect

video and audio sources.

To the wall outlet.

Your projector is simple to set up and use. But before you get started, you

must first:

z Set up a screen and the projector.

x Connect your computer or video equipment to the projector. See page E-

27.

c Connect the supplied power cable. See page E-35.

NOTE: Ensure that the power cable and any other cables are disconnected

before moving the projector.

When moving the projector or when it is not in use, cover the lens with the lens

cap.

E-21

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Setting Up the Screen and theProjector

Setting Up the Screen and the Projector

Selecting a Location

The further your projector is from the screen or wall, the larger the image.

The minimum size the image can be is approximately 30" (0.8 m) mea-

sured diagonally when the projector is roughly 4 feet (1.3 m) from the wall

or screen.The largest the image can be is 500" (12.7 m) when the projec-

tor is about 80.83 feet (24.64 m) from the wall or screen. Use the drawing

below as a guide.

Screen size (Unit: cm/inch)

406.4(W)

304.8(H)/160"(w)

365.8(W)

120"(H)

274.3(H)/144"(W)

Screen size

304.8(W)

108"(H)

228.6(H)/120"(W)

200"

180"

243.8(W)

90"(H)

182.9(H)/96"(W)

203.2(W)

162.6(W)

72"(H)

150"

152.4(H)/80"(W)

60"(H)

121.9(H)/64"(W)

120"

100"

121.9(W)

48"(H)

91.4(H)/48"(W)

81.3(W)

36"(H)

61.0(H)/32"(W)

80"

61.0(W)

24"(H)

45.7(H)/24"(W)

60"

18"(H)

Lens center

40"

30"

1.3/4.3

(1.0/3.3)

1.7/5.6

(1.3/4.3)

2.6/8.5

(2.0/6.6)

3.5/11.5

(2.7/8.9)

4.4/14.4

(3.4/11.2)

5.3/17.4

(4.1/13.5)

7.9/25.9

(6.2/20.34)

6.6/21.7

(5.2/17.1)

8.8/28.9

(6.9/22.6)

Distance (Unit: m/feet)

NOTE: Values in parentheses for LT240K.

E-22

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Setting Up the Screen and theProjector

Throw Distance and Screen Size

The following shows the proper relative positions of the projector and screen.

Refer to the table to determine the position of installation.

Distance Chart

Screen Width

Screen Diagonal

Screen Height

Screen center

(B)

Screen Bottom

(D)

Lens Center

Throw Angle (Ͱ)

Throw Distance (C)

B = Vertical distance between lens center and screen center

C = Throw distance

D = Vertical distance between lens center and bottom of screen

α = Throw angle

E-23

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Setting Up the Screen and theProjector

B = Vertical distance between lens center and screen center

C = Throw distance

D = Vertical distance between lens center and bottom of screen

α = Throw angle

NOTE: Distances may vary +/-5%.

Screen Size

Width

inch

Diagonal

inch

Height

inch

108

120

126

144

157

162

180

210

240

270

300

Wide – Tele

degree

inch

12.6

16.8

25.3

28.2

30.3

33.7

35.4

37.9

42.1

50.5

63.2

75.8

84.2

88.4

101.1

109.9

113.7

126.3

147.4

168.5

189.5

210.6

inch

3.6

4.8

7.3

8.1

inch

46.4 – 57.0

62.4 – 76.4

94.5 – 115.3

105.8 – 128.9

113.8 – 138.6

126.6 – 154.1

133.0 – 161.9

142.7 – 173.6

158.7 – 193.0

190.8 – 231.8

239.0 – 290.1

287.1 – 348.4

319.2 – 387.2

335.3 – 406.7

383.4 – 464.9

417.1 – 505.7

431.6 – 523.2

479.7 – 581.5

560.0 – 678.6

640.2 – 775.7

720.5 – 872.9

800.7 – 970.0

15.2 - 12.5

15.1 - 12.4

15.0 - 12.4

14.9 - 12.3

14.8 - 12.3

14.7 - 12.3

14.7 - 12.2

8.7

9.7

10.2

10.9

12.1

14.5

18.2

21.8

24.2

25.4

29.1

31.6

32.7

36.3

42.4

48.5

54.5

60.6

100

120

150

180

200

210

240

261

270

300

350

400

450

500

120

144

160

168

192

209

216

240

280

320

360

400

Screen Size

Width

Diagonal

762

Height

457

Wide – Tele

degree

321

610

1178 - 1448

1586 - 1942

2401 - 2928

2686 - 3274

2890 - 3520

3216 - 3915

3379 - 4113

3624 - 4409

4032 - 4902

4847 - 5889

6070 - 7369

7293 - 8849

8108 - 9836

8516 -10329

9739 -11810

10595 -12846

10962 -13290

12185 -14770

14223 -17237

16261 -19704

18299 -22171

20338 -24638

15.2 - 12.5

15.1 - 12.4

15.0 - 12.4

14.9 - 12.3

14.8 - 12.3

14.7 - 12.3

14.7 - 12.2

1016

1524

1702

1829

2032

2134

2286

2540

3048

3810

4572

5080

5334

6096

6629

6858

7620

8890

10160

11430

12700

813

610

914

428

642

716

770

855

898

962

1069

1283

1604

1925

2139

2246

2567

2792

2888

3209

3744

4279

4814

5349

123

184

206

221

246

258

277

307

369

461

554

615

646

738

803

831

923

1077

1231

1385

1539

1219

1361

1463

1626

1707

1829

2032

2438

3048

3658

4064

4267

4877

5304

5486

6096

7112

8128

9144

10160

1021

1097

1219

1280

1372

1524

1829

2286

2743

3048

3200

3658

3978

4115

4572

5334

6096

6858

7620

E-24

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Setting Up the Screen and theProjector

B = Vertical distance between lens center and screen center

C = Throw distance

D = Vertical distance between lens center and bottom of screen

α = Throw angle

NOTE: Distances may vary +/-5%.

Screen Size

Width

inch

Diagonal

inch

Height

inch

108

120

126

144

157

162

180

210

240

270

300

Wide – Tele

degree

inch

12.6

16.8

25.2

28.1

30.2

33.6

35.3

37.8

42.0

50.4

63.0

75.6

84.0

88.2

100.8

109.7

113.4

126.1

147.1

168.1

189.1

210.1

inch

3.6

4.8

7.2

8.0

35.7 - 43.4

48.2 - 58.4

73.2 - 88.5

81.9 - 99.0

88.1 - 106.5

98.1 - 118.6

103.1 - 124.6

110.6 - 133.6

123.1 - 148.6

148.1 - 178.7

185.5 - 223.8

223.0 - 268.9

248.0 - 298.9

260.5 - 314.0

297.9 - 359.1

324.1 - 390.6

335.4 - 404.1

372.8 - 449.2

435.3 - 524.4

497.7 - 599.6

560.1 - 674.7

622.5 - 749.9

19.4 - 16.2

19.2 - 16.0

19.0 - 15.9

18.9 - 15.8

18.8 - 15.8

18.8 - 15.7

18.7 - 15.7

18.6 - 15.7

8.6

9.6

10.1

10.8

12.0

14.4

18.0

21.6

24.0

25.2

28.8

31.4

32.4

36.1

42.1

48.1

54.1

60.1

100

120

150

180

200

210

240

261

270

300

350

400

450

500

120

144

160

168

192

209

216

240

280

320

360

400

Screen Size

Width

Diagonal

762

Height

457

Wide – Tele

degree

320

610

907 - 1102

1224 - 1484

1858 - 2248

2080 - 2515

2239 - 2706

2493 - 3011

2620 - 3164

2810 - 3393

3127 - 3775

3761 - 4538

4713 - 5684

5664 - 6829

6298 - 7593

6615 - 7975

7567 - 9120

8233 - 9922

8518 -10265

9470 -11411

11055 -13320

12641 -15229

14227 -17138

15813 -19046

19.4 - 16.2

19.2 - 16.0

19.0 - 15.9

18.9 - 15.8

18.8 - 15.8

18.8 - 15.7

18.7 - 15.7

18.6 - 15.7

1016

1524

1702

1829

2032

2134

2286

2540

3048

3810

4572

5080

5334

6096

6629

6858

7620

8890

10160

11430

12700

813

610

914

426

640

715

768

853

896

960

1067

1280

1601

1921

2134

2241

2561

2785

2881

3202

3735

4269

4803

5336

122

183

204

219

244

256

274

305

366

458

549

610

641

732

797

824

916

1068

1221

1374

1526

1219

1361

1463

1626

1707

1829

2032

2438

3048

3658

4064

4267

4877

5304

5486

6096

7112

8128

9144

10160

1021

1097

1219

1280

1372

1524

1829

2286

2743

3048

3200

3658

3978

4115

4572

5334

6096

6858

7620

E-25

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Setting Up the Screen and theProjector

WARNING

Installing your projector on the ceiling must be done by a qualified tech-

nician. Contact your NEC dealer for more information.

•

Do not attempt to install the projector yourself.

Only use your projector on a solid, level surface. If the projector falls to

the ground, you can be injured and the projector severely damaged.

•

Do not use the projector where temperatures vary greatly.The projector

must be used at temperatures between 41˚F (5˚C) and 95˚F (35˚C).

Do not expose the projector to moisture, dust, or smoke.This will harm

the screen image.

Ensure that you have adequate ventilation around your projector so

heat can dissipate. Do not cover the vents on the side or the front of the

projector.

Reflecting the Image

Using a mirror to reflect your projector's image enables you to enjoy a

much larger image. Contact your NEC dealer if you need a mirror. If you're

using a mirror and your image is inverted, use the MENU and SELECT

buttons on your projector cabinet or ̆̄ buttons on your remote control to

correct the orientation. (See page E-95.)

E-26

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS

Making Connections

Wiring Diagram

Monitor

Document Camera

VCR, DVD Player or

LaserDisc Player

To video, S-video, and au-

dio inputs on the projector.

RGB Signal cable (supplied)

Optional 15-pin-to-RCA

To mini D-Sub 15-pin connector on the pro-

jector. It is recommended that you use a com-

mercially available distribution amplifier if con-

necting a signal cable longer than the sup-

plied cable.

(female)

3 cable

(ADP-CV1)

DVD Player

(with component output)

IBM VGA or Compatibles

(Desktop type or notebook type)

Macintosh

(Desktop type or notebook type)

NOTE: When using with a notebook PC, be sure to connect between the projector

and the notebook PC before turning on the power to the notebook PC. In most

cases signal cannot be output from RGB output unless the notebook PC is turned

on after connecting with the projector.

If the screen goes blank while using your remote control, it may be the result of

the computer's screen-saver or power management software.

If you accidentally hit the POWER button on the remote control, wait 90 sec-

onds and then press the POWER button again to resume.

E-27

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Making Connections

To connect SCART output (RGB)

Before connections: An exclusive SCART adapter (ADP-SC1) and a com-

mercially available SCART cable are required for this connection.

NOTE:

•

Audio signal is not available for this connection.

The RGB IN 2 connector does not support SCART signal and Plug & Play.

Video equipment

such as DVD player

Y B D N

C N A C

C R U

D R

N E

Projector

To RGB IN 1

ADP-SC1

Commercially available SCART cable

Female

1. Turn off the power to the projector and your video equipment.

2. Use the NEC ADP-SC1 SCART adapter and a commercially available

SCART cable to connect the RGB 1 input of your projector and a SCART

output (RGB) of your video equipment.

3. Turn on the power to the projector and your video equipment.

4. Use the RGB 1 button on the remote control to select the RGB 1 input.

5. Press the MENU button on the remote control to display the menu.

6. From the Advanced menu, select [Projector Options] → [Setup] → [Page

3] → [Signal Select RGB1] → [Scart].

SCART is a standard European audio-visual connector for TVs, VCRs

and DVD players. It is also referred to as Euro-connector.

NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in

Europe. Contact your NEC dealer in Europe for more information.

E-28

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Making Connections

Connecting Your PC or Macintosh Computer

AUDIO IN

RGB IN1

RGB IN2

RGB signal cable (supplied)

To mini D-Sub 15-pin connector on the

Audio cable (not supplied)

projector. It is recommended that you use

a commercially available distribution am-

plifier if connecting a signal cable longer

than the supplied one.

PHONE

IBM VGA or Compatibles (Note-

book type) or Macintosh (Note-

book type)

IBM VGA or Compatibles (Desktop type)

or Macintosh (Desktop type)

NOTE: For older Macintosh, use a commercially available pin adapter (not sup-

plied) to connect to your Mac's video port.

E-29

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Making Connections

Connecting your PC or Macintosh computer to your projector will enable

you to project your computer's screen image for an impressive presenta-

tion.

To connect to a PC or Macintosh, simply:

1. Turn off the power to your projector and computer.

2. Use the supplied signal cable to connect your PC or Macintosh to the

projector.

3. Turn on the projector and the computer.

4. If the projector goes blank after a period of inactivity, it may be caused

by a screen saver installed on the computer you've connected to the pro-

jector.

NOTE: The LT260K/LT240K is not compatible with video decoded outputs of

NEC ISS-6020 and ISS-6010.

E-30

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Making Connections

Connecting an External Monitor

RGB OUT

You can connect a separate, external monitor to your projector to simulta-

neously view on a monitor the RGB analog image you're projecting.To do

so:

1. Turn off the power to your projector, monitor and computer.

2. Use a 15-pin cable to connect your monitor to the RGB OUT (Mini D-Sub

15 pin) connector on your projector.

3. Turn on the projector, monitor and the computer.

NOTE: The RGB OUT connector outputs RGB signal during idle mode (See page

E-100). When the projector goes into idle mode, the image on an external monitor

disappears for a moment. Note that the RGB OUT connector will not output RGB

signal during Standby mode.

• Daisy chain connection is not possible.

E-31

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Making Connections

Connecting Your Video Equipment

Connecting Your DVD Player

RGB IN1 or IN2

Optional 15-pin-to-RCA

(female)

3 cable (ADP-CV1)

Audio Equipment

Component video

RCA

3 cable

(not supplied)

AUDIO IN

DVD player

AUDIO OUT

COMPONENT OUT

Audio cable (not supplied)

You can connect your projector to a DVD player with component output or

Video output. To do so, simply:

1. Turn off the power to your projector and DVD player.

2. If your DVD player has the component video (Y,Cb,Cr) output, use a com-

mercially available component video cable (RCA

3) and the optional

15-pin-to-RCA (female)

3 cable to connect your DVD player to the RGB

IN1 or IN2 connector on the projector.

For a DVD player without component video (Y,Cb,Cr) output, use com-

mon RCA cables (not provided) to connect a composite VIDEO output of

the DVD player to the Video Input of the projector.

3. Turn on the projector and DVD player.

NOTE: Refer to your DVD player's owner's manual for more information about

your DVD player's video output requirements,

E-32

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Making Connections

Connecting Your VCR or Laser Disc Player

VIDEO IN

S-VIDEO IN

S-video cable (not supplied)

Audio equipment

Video cable (not supplied)

AUDIO IN

VCR/ Laser disc player

AUDIO OUT

S-VIDEO OUT

VIDEO OUT

Audio cable (not supplied)

Use common RCA cables (not provided) to connect your VCR, laser disc

player or document camera to your projector.

To make these connections, simply:

1. Turn off the power to the projector and VCR, laser disc player or docu-

ment camera.

2. Connect one end of your RCA cable to the video output connector on the

back of your VCR or laser disc player, connect the other end to the Video

input on your projector. Use an audio cable (not supplied) to connect the

audio from your VCR or laser disc player to your audio equipment (if

yourVCR or laser disc player has this capability). Be careful to keep your

right and left channel connections correct for stereo sound.

E-33

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Making Connections

3. Turn on the projector and the VCR or laser disc player.

NOTE: Refer to your VCR or laser disc player owner's manual for more informa-

tion about your equipment's video output requirements.

NOTE: An image may not be displayed correctly when a Video or S-Video source

is played back in fast-forward or fast-rewind via a scan converter.

E-34

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS Ͼ Making Connections

Connecting the Supplied Power Cable

Connect the supplied power cable to the projector.

First connect the supplied power cable's three-pin plug to the AC IN of the

projector, and then connect the other plug of the supplied power cable in

the wall outlet.

E-35

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

(BASIC OPERATION)

This section describes how to turn on the projector and to project a picture

onto the screen.

Turning on the Projector

NOTE:

•

When plugging in or unplugging the supplied power cable, make sure that the

main power switch is pushed to the off[O] position. Failure to do so may

cause damage to the projector.

•

The projector has two power switches: main power switch and POWER but-

ton (POWER ON and OFF on the remote control)

The projector has a feature to prevent itself from being used by unauthorized

individuals. To use this feature, register your PC card as a protect key. See

"Security" in "Projector Options" on page E-114 for more details.

To turn on the main power to the projector, press the Main Power switch to

the ON position ( I ).

Before you turn on your projector, ensure that the computer or video source

is turned on and that your lens cap is removed.

Only after you press the ON/STAND BY button on the projector cabinet or

POWER ON button on the remote control for a minimum of 2 seconds will

the power indicator turn to green and the projector become ready to use.

E-36

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE Ͼ Turning on the Projector

Note on Startup screen (Menu Language Select screen)

When you first turn on the projector, you will get the Startup screen. This

screen gives you the opportunity to select one of the seven menu lan-

guages: English, German, French, Italian, Spanish, Swedish and Japa-

nese.

To select a menu language, follow these steps:

1. Use the SELECT ̆ or ̄ button to select one of the seven languages for

the menu.

SELECT

2. Press the ENTER button to execute the selection.

SELECT

E-37

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE Ͼ Turning on the Projector

3. The Basic menu will be displayed in the language you have selected.

SELECT

To close the menu, press the CANCEL button.

After this has been done, you can proceed to the advanced menu opera-

tion.

If you want, you can select the menu language later. See "Language" on

page E-93.

NOTE: To turn the projector on by plugging in the power cable, first turn on the

Main Power switch to ON and use the menu and enable the "Auto Start" feature.

(See page E-99.)

Immediately after turning on the projector, screen flicker may occur. This is not a

fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.

When the Lamp mode is set to Eco, the Lamp indicator will light green.

If one of the following things happens, the projector will not turn on.

* If the internal temperature of the projector is too high, the projector

detects abnormal high temperature. In this condition the projector

will not turn on to protect the internal system. If this happens, wait for

the projector's internal components to cool down.

* When the lamp reaches its end of usable life, the projector will not

turn on. If this happens, replace the lamp.

* If the lamp fails to light, and if the STATUS indicator flashes on and

off in a cycle of six times, wait a full minute and then turn on the

power.

E-38

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

Selecting a Source

Selecting the computer or video source

Using the Remote Control

OFF

POWER

S-VIDEO RGB1

VIDEO

AUTO ADJ.

RGB2

LASER

Press any one of the RGB1,

RGB2, VIDEO, S-VIDEO or

VIEWER buttons.

ASPECT FREEZE 3D REFORM

HELP

POINTER VIEWER

VOLUME MAGNIFY

SLIDE

PICTURE

FOLDER

SLIDE

PIC-MUTE

LIST

NOTE: If no input signal is available, the projector will display a blue back-

ground (factory preset).

Selecting from Source List

Source List

Press and quickly release the SOURCE button on the projector cabi-

net to display the Source list.Each time the SOURCE button is pressed,

the input source will change as follows: "Video" (VCR, document cam-

era, or laser disc player), S-Video", "RGB1" or "RGB2" (computer or

DVD with component output) , "Viewer" (slides on a PC card), or "LAN"

(wired or wireless signal aired from a PC).

To display the selected source, press the ENTER button.

E-39

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE Ͼ Selecting a Source

Detecting the Signal Automatically

Press and hold the SOURCE button for a minimum of ONE second,

the projector will search for the next available input source. Each time

you press and hold the SOURCE button, the input source will change

as follows:

→ RGB1 → RGB2 → Video → S-Video → Viewer 

If no input signal is present, the input will be skipped. When the input

source you wish to project is displayed, release the button.

Press the ENTER button.

E-40

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

Adjusting the Picture Size and Position

Place your projector on a flat level surface and ensure that the projector is

square to the screen.

Lift the front edge of the projector to center the image vertically.

Move the projector left to center the image horizontally on the screen.

Use the 3D REFORM feature for proper adjustment. See page E-44.

Geometric Correction Tool

If you use a special shaped screen such as a cylindrical or spherical

screen, a downloadable program, Geometric Correction Tool is available.

This program (Geometric Correction Tool) enables the geometrical distor-

tion correction of an image when projected onto a special shaped screen

with a NEC projector. Additionally, this program allows control of the pro-

jector via a computer.

For additional information visit:

US : http://www.necvisualsystems.com

Europe : http://www.nec-europe.com/

Global : http://www.nec-pj.com/

E-41

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE Ͼ Adjusting the Picture Size and Position

Adjust the Tilt Foot

q Lift the front edge of the projector.

Y B

D N

E C N

E C R U

- C

E S

N E

Adjustable Tilt

Foot Lever

Adjustable Tilt Foot

w Push up the Adjustable Tilt Foot Lever on the front of the projector to

extend the adjustable tilt foot (maximum height).

e Push down the Adjustable Tilt Foot Lever.

Y B

D N

E C N

C R U

E S

N E

r Lower the front of the projector to the desired height and release the

Adjustable Tilt Foot Lever to lock the Adjustable tilt foot. There is ap-

proximately 7 degrees of up and down adjustment for the front of the

projector.

E-42

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE Ͼ Adjusting the Picture Size and Position

The rear foot height can be changed. Rotate the rear foot to the desired

height, but the vertical distance from the bottom to the desk or floor should

be 1" (25 mm) to make the projector horizontal on the flat surface.

Down

* If the projected image does not appear square to the screen then

use the 3D Reform feature for proper adjustment. See page E-44.

CAUTION:

Do not use the tilt-foot for purposes other than originally intended. Mis-

uses such as gripping the tilt-foot or hanging on the wall can cause

damage to the projector.

Zoom

Use the Zoom lever to fine adjust

the image size on the screen

Focus

Use the Focus ring to obtain the

best focus.

E-43

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

Correcting the Horizontal and Vertical Keystone Distortion (3D Reform)

Use the 3D Reform feature to correct keystone (trapezoidal) distortion to

make the top or bottom and the left or right side of the screen longer or

shorter so that the projected image is rectangular.

You can also use a mouse to correct the Cornerstone distortion. To do so

with your mouse, pick and left-click on one corner of the image you want to

correct.

Do this for the remaining 3 corners. Right-click to display the confirmation

screen.

1. Project an image so that the screen is smaller than the area of the raster.

2. Pick up any one of the corners and align the corner of the screen with the

one of the image.

Projected image

Screen

(The drawing shows the upper right corner.)

3. Press the 3D REFORM button on the remote control.

The CORNERSTONE adjustment screen is displayed.

NOTE: Press the 3D REFORM button to toggle between "Cornerstone" and "Key-

stone."

E-44

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

4. Use the SELECT ̆̄̇̈ button to select one icon which points in the

direction you wish to move the projected image frame.

Screen

5. Press the ENTER button.

6. Use the SELECT ̆̄̇̈ button to move the projected image frame as

shown on the example.

7. Press the ENTER button.

Screen

8. Use the SELECT ̆̄̇̈ button to select another icon which points in

the direction.

On the Cornerstone adjustment screen,

select “Exit”and then “OK”, or press the

CANCEL button on the remote control.

Screen

The confirmation screen is displayed.

E-45

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

9. Press the SELECT ̇ or ̈ button to highlight the [OK] and press the

ENTER button.

This completes the keystone correction.

Selecting “Cancel” will return to the adjustment screen without saving

changes (Step 3).

Selecting "Reset" will return to the factory default.

Selecting "Undo" will exit without saving changes.

NOTE: To return the 3D Reform correction setting values to the factory default,

press and hold the 3D REFORM button for a minimum of 2 seconds.

NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be

available. Should this happen, first reset the 3D Reform data and then do each

setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/or

Screen setting can limit 3D Reform in its adjustable range.

The adjustable ranges for 3D Reform are as follows:

Horizontal ............. Max 30° approx. (Max 25° approx. on LT240K)

Vertical ................. Max 40° approx.

* The following are conditions at the above maximum angle when all of

the following are met

• Image is projected in Wide (Zoom)

• Resolution is XGA

Higher resolution than XGA limits 3D Reform in its adjustable range.

• Menu items should be set as follows:

Aspect Ratio........... 4:3

Screen Type ........... 4:3

• Horizontal and Vertical are adjusted separately.

A combination of both adjustments limits 3D Reform in its adjustable

range.

E-46

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

Optimizing RGB Picture Automatically

Adjusting the Image Using Auto Adjust

Optimizing RGB image automatically

Press the Auto Adjust button to optimize an RGB image automatically.

[Poor picture]

AUTO ADJ.

[Normal picture]

Press the Auto Adjust button to fine-tune the computer image or to remove

any vertical banding that might appear and to reduce video noise, dot

interference or cross talk (this is evident when part of your image appears

to be shimmering). This function adjusts the clock frequencies that elimi-

nate the horizontal banding in the image. This function also adjusts the

clock phase to reduce video noise, dot interference or cross talk. (This is

evident when part of your image appears to be shimmering.)

This adjustment may be necessary when you connect your computer for

the first time.

NOTE:

•

Some signals may not be displayed correctly or take time.

The Auto Adjust function does not work for component and video signal.

If the Auto Adjust operation cannot optimize the RGB signal, try to adjust

Clock and Phase manually. See page E-88.

E-47

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

Turning Up or Down Volume

Sound level from the speaker and the AUDIO OUT mini jack on the projec-

tor can be adjusted.

VOLUME

Volume bar

increase volume

decrease volume

Using the Laser Pointer

You can use the laser to draw your

audience's attention to a red dot that you

can place on any object.

Press and hold the LASER button to acti-

vate the laser pointer.

-V

LASER

-M

LID

CAUTION:

• Do not look into the laser pointer while it is on.

• Do not point the laser beam at a person.

E-48

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

Setting the function switch

There are two switches on the bottom of

the battery case: an applicable projector

selector switch (1) and laser enable/dis-

able switch (2). Check the projector be-

ing used and decide whether to enable

or disable laser, then set these switches

as necessary using the tip of a thin ball-

point pen. On this model, an applicable

projector selector switch (1) is not used.

OFF

Switch (2)

On: Enabled (the laser lights when the LASER button is pressed)

[Factory default]

Off: Disabled (the laser does not light even when the LASER button

is pressed)

Disable the laser when using in an environment in which the unit is acces-

sible to children.

E-49

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE

Turning off the Projector

To turn off the projector:

OFF

POWER

S-VIDEO RGB1

First press the POWER (ON/STAND BY) but-

ton on the projector cabinet or the POWER OFF

button on the remote control for a minimum of

two seconds. The power indicator will glow or-

ange. After the projector turns off, the cooling

fans keep operating for 90 seconds (Cooling-

off time).

VIDEO

AUTO ADJ.

RGB2

LASER

ASPECT FREEZE 3D REFORM

HELP

POINTER VIEWER

SLIDE

VOLUME MAGNIFY

Second, turn off the Main Power switch. The

power indicator will go out. Last unplug the

power cable.

PICTURE

FOLDER

SLIDE

PIC-MUTE

LIST

CAUTION

Do not unplug the power cable from the wall

outlet or do not turn off the main power under

any one of the following circumstances. Doing

so can cause damage to the projector:

•

While the Hour Glass icon appears.

While the message "Please wait a moment."

appears. This message will be displayed

after the projector is turned off.

•

While the cooling fans are running. (The

cooling fans continue to work for 90 sec-

onds after the projector is turned off).

While accessing a PC card. (The PC Card

Access indicator lights.)

E-50

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

Using the Remote Mouse Function

The built-in remote mouse function enables you to operate your computer's

mouse functions from the remote control (Computer mode). It is a great

convenience for clicking through your computer-generated presentations.

To return to the projector operation mode (Projector mode), press the PJ

button (lit red).

Connecting to your computer for the remote mouse

fuction

If you wish to use the remote mouse function, use the supplied USB cable

to connect the USB port (type B) of the projector and the USB port (type

A) of your computer.

NOTE: Depending on the type of connection or OS installed on your computer,

you may have to restart your computer or change you computer settings.

When using the USB Port

For PC, the mouse receiver function can only be used with a Windows 98,

Windows ME, Windows XP or Windows 2000 operating system.

Type B

Type A

NOTE: Wait at least 5 seconds after disconnecting the USB cable before recon-

necting it and vice versa. The computer may not identify the built-in mouse re-

ceiver if it is repeatedly connected and disconnected in rapid intervals.

E-51

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES Ͼ Using the Remote Mouse Function

Switching operation mode between computer and pro-

jector

The three shaded buttons shown on the drawing work as a computer mouse

in the Computer mode.

In the Computer mode the PJ button is not lit.

Works as a mouse

for your computer.

Works as the Select button

on the projector.

OFF

POWER

S-VIDEO RGB1

POWER

S-VIDEO RGB1

VIDEO

AUTO ADJ.

RGB2

LASER

VIDEO

AUTO ADJ.

RGB2

LASER

SELECT

Works as the Cancel

button on the

projector.

Works as a right-

click button for

your computer.

Not lit

Lit red

FOCUS

HELP

ZOOM

SHIFT

FOCUS

HELP

ZOOM

SHIFT

POINTER PC CARD

KEYSTONE MAGNIFY

SLIDE

KEYSTONE MAGNIFY

SLIDE

FREEZE

VOLUME

FOLDER

SLIDE

FREEZE

VOLUME

FOLDER

SLIDE

PIC-MUTE

LIST

Works as a left-click button

for your computer.

Works as the Enter button

on the projector.

E-52

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES Ͼ Using the Remote Mouse Function

• When the MENU button is pressed, the PJ button lights red to indi-

cate that you are in the Projector mode, which allows the projector

menu operation using the three buttons.

• When the POINTER button is pressed, the PJ button lights red to

indicate that you are in the Projector mode and that the SELECT

̆̄̇̈ button works as a moving button for the POINTER or magni-

fied image.

• If no buttons are pressed within 60 seconds, the PJ button's light

goes out to indicate that you are in the Computer mode. To enable

the projector menu operation again, press the PJ button to light red.

To move the pointer or a magnified image again, turn off the pointer

and then turn on the pointer (press the POINTER button two times).

• When the PJ button is lit, if you want to use the mouse function im-

mediately, press the PJ button to return to the Computer mode (not

lit).

During Computer mode:

In Computer mode, by pressing the ENTER button for 2 seconds or more

then releasing, the drag mode is set and the drag operation can be per-

formed simply by pressing the SELECT ̆̄̇̈ (mouse) button.To set the

drag-and-drop, press the ENTER (left click) button again. To cancel the

drag mode, press the CANCEL (right click) button.

E-53

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

Turning Off the Image and Sound

PIC-MUTE

Press the Picture Mute button to turn off the image

and sound for a short period of time. Press again to

restore the image and sound.

Freezing a Picture

FREEZE

Press the Freeze button to freeze a picture. Press

again to resume motion.

Using the Projector Pointer

You can use one of nine pointers to draw your

audience's attention to the portion of a projected

image you want.

POINTER

Press the Pointer button to dis-

play the projector pointer.

Press the Pointer button to display the projector pointer.

SELECT

Use the Select button to

move the projector pointer.

Use the Select button to move the projector pointer.

E-54

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

Enlarging and Moving a Picture

You can enlarge the area you want up to 400 percent.

To do so:

1. Press the Pointer button to display the projector pointer.

POINTER

2. Move the projector pointer to the area you want to enlarge.

SELECT

3. Enlarge the selected area.

When the Magnify (+) button is pressed, the pointer is changed to a mag-

nifying glass. To move the magnifying glass, use the SELECT button.

MAGNIFY

4. Return the image to the original size.

MAGNIFY

E-55

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

Getting the On-line Help

You get the contents about Help.

HELP

SELECT

Display Help

Exit Help

USB Memory Device or USB Memory Card Reader Support

The projector is compatible with either a USB memory device or USB

memory card reader which supports the viewer and security features.

•

To use a USB memory device or USB memory card reader, connect

the device to the USB port (type A).

Select one of the Drive icons in theViewer toolbar, Capture toolbar and

PC Card File setting screen. Up to four drives can be accepted.

To use a USB memory device as a Protect key for Security function,

select one from the Drive icons in the Security setting screen.

E-56

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

NOTE:

•

Some USB memory devices (brands) or USB memory card readers may not

work.

•

You cannot use a USB memory device and a USB memory card reader when

connecting a USB mouse to the projector.

Using a USB HUB that allows multiple USB memory devices or card readers

is not supported either.

•

Do not do the following while the USB memory device or USB memory card

reader’s access indicator is lit or flashing (while data is being accessed.)

Doing so can damage your USB memory device or USB memory card in the

reader. Back up your data in case it will need to be restored.

Pulling out the USB memory device or USB memory card reader from the

USB port of the projector.

•

Pulling out the memory card from the USB memory card reader

Turning off the main power switch or unplugging the power cable.

The drive for ”USB 1-4” is displayed only when the USB memory device or

USB memory card reader is connected to the projector. The drive for “USB 1-

4” may be displayed differently from the one in the USB memory card reader.

Some USB memory devices (brands) or USB memory cards cannot be used as

Protect key for the projector’s Security function.

•

E-57

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

Using a USB Mouse

Using a USB mouse gives you a smooth operation. A commercially avail-

able USB mouse is required.

Type A

USB

NOTE: There may be some brands of USB mouse that the projector does not

support.

Operate the Menus using the USB mouse

Mouse Cursor

When connecting a USB mouse to the projector, you get a mouse cur-

sor on the screen.

Unless you use your USB mouse within 10 seconds, the mouse cursor

disappears.

Menu Display

Clicking with a mouse button displays the menu.

Clicking ̈ displays the pull-down menu. To close the menu, click any-

where in the background.

Adjusting and Setting Display

You can select a menu item and click with a mouse button to make

adjustments and setting.

Using the middle button on the mouse

The projector supports the middle button on your mouse. With the

middle button you can use a scroll bar when it is available or click the

middle button to display or hide the Chalkboard toolbar.

E-58

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

Examples

Click (or press and hold) the mouse button ̇ or ̈ to adjust the bright-

ness. Or click and drag the mouse button on the slide bar horizontally

to adjust it.

To save the adjustments, click . The display is closed. If you click

anywhere in the background while displaying adjustment and setting

menu or dialog box, you will get the main menu at the clicking point.

Changing Background Logo

You can change the default background logo using the PC Card Files fea-

ture.

NOTE: File size must be 256KB or less. Other file formats than JPEG and BMP

are not available.

1. From the menu, select [Tools] → [PC Card Files] to display a list of all the

files stored in the PC card so that you can select a file you want to use as a

background logo.

2. The Logo button allows you to select a background logo from graphic

files on a PC card and change to it as the background logo.

3. Use the SELECT ̆ or ̄ button to select a JPEG or BMP file for your

background logo.

E-59

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES Ͼ Changing Background Logo

4. Use the SELECT ̈ and then ̄ button to select "Logo".

5. Press the ENTER on the remote control or the cabinet. You will get the

confirmation dialog box.

6. Select "OK" and press the ENTER button. This completes changing a

logo for the background.

Once you have changed the background from the NEC logo to an-

other, you cannot return the logo to background even by using Factory

Default.To do so, repeat the above steps.The NEC logo file is included

on the supplied CD-ROM NEC Projector User Supportware (/Logo/

nec_b_x.jpg).

E-60

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

Making Freehand Drawings on a Projected Image (ChalkBoard)

The ChalkBoard feature allows you to write and draw messages on a pro-

jected image.

NOTE: The ChalkBoard feature is available only when a USB mouse is used.

From the menu, select [Tools] → [ChalkBoard] to display the ChalkBoard

tool bar that cotains the following icons.

Eraser

Hide

Pen

Drag

Exit

Color

Clear

Capture

Drag ..... Drags to move the tool bar by clicking on the blue part. (for USB

mouse operation only)

Pen ....... Left-click and drag to draw. Left-click [̆] or right-click the pen

icon to display the pen palette containing four lines of different

thickness from which you can select a line you prefer by left-

clicking.

Color..... Selects a color. Left-click to display the color palette from which

you can select a color you prefer by left-clicking.

Capture Left-click to capture and save freehand drawings in the PC card.

Eraser... Left-click and drag to erase part of a drawing. Left-click [̆] or

right-click the eraser icon to display the eraser palette contain-

ing four eraser of different thickness from which you can select

an eraser you prefer by left-clicking.

Clear..... Left-click to clear the drawing completely from the ChalkBoard

screen.

Hide ...... Hides the tool bar by left-clicking. Right-clicking anywhere on

the screen displays the ChalkBoard tool bar again.

Exit ....... Clears the complete drawing and exits the ChalkBoard.

NOTE:

•

The menu is not available while you display the ChalkBoard screen.

Switching slides clears a drawing completely.

E-61

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

NOTE: To use the Viewer, first you need to create presentation materials on your

PC using the Dynamic Image Utility 2.0 contained on the supplied NEC Projec-

tor User Supportware CD-ROM.

For installation, see the printed Application Guide. For creating presentation

materials, see the Slide show function on the on-line manual of the Dynamic Im-

age Utility 2.0.

Making the Most out of the Viewer Function

Features

You can view presentation data, capture, and play images on the projec-

tor. A PC card is used to view presentation data prepared on the computer

and to capture and play images projected with the projector.

The Viewer feature allows you to view slides stored on a PC memory card

(referred to as PC card in this manual) on the projector. Even if no com-

puter is available, presentations can be conducted simply with the projec-

tor.This feature is convenient for holding presentations at meetings and in

offices, as well as for playing images taken on digital cameras.

Easy to use

• Presentations can be started immediately simply by inserting a PC

card (not supplied)

• Easy slide switching

• Remote control operation

• Jumping to list of slides or any specific slide

High quality images

• High resolution up to 1024 x 768 dots

• 24-bit full color playback

• Viewing of digital camera images

E-62

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

Simple utility software (for computer)

• Dynamic Image Utility 2.0 operable on Windows 98/Me/XP/2000

• Slides can be created by capturing the currently displayed image

• Control screen for displaying lists of slides and editing

* Microsoft, Windows and PowerPoint are registered trademarks of

Microsoft Corporation.

Inserting and Removing a PC Card

Inserting the PC Card

• Hold the PC card horizontally and insert it slowly into card slot with

its top facing up.

• The eject button pops out once the PC card is fully inserted. Check

that the PC card is fully inserted.

NOTE: Do not try to force the PC card into the slot.

PC card (not supplied)

E-63

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

Removing the PC Card

Press the eject button. The PC card pops out a little. Grasp the edges

of the PC card and pull it out.

NOTE: Do not eject the PC card while its data is being accessed.

Eject button

Direction for Inserting the PC Card

The PC card has a top and bottom and must be inserted into the PC card

slot in a specific direction.It cannot be inserted backwards or upside-down.

Attempting to force it into the slot in the wrong direction may break the

internal pin and damage the card slot. Refer to the PC card's operating

instructions for the proper direction of insertion.

PC Card Type

The PC Card slot accepts PCMCIA Type II only.

CAUTION:

•

Do not use CompactFlash type cards except for flash memory cards.

Using a CompactFlash card with the help of a PC card adapter could

cause damage to the CompactFlash card.

•

Back up your PC card's data in case it will need to be restored.

E-64

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

Operating the Viewer Function from the Projector (playback)

This section describes the operation for showing slides of presentation

documents created using the Viewer function with the projector. It is also

possible to make slides directly from the images projected with the projec-

tor.

Projecting slides (Viewer)

1. Insert a PC card into the PC card slot.

Insert the PC card with the side with the insertion direction arrow on the

top.

Press the eject button to eject the card.

2. Select the "Viewer" from the Source Select menu.

3. Project slides.

Checking "Show Folder List", means that selectingViewer input displays

a list of the folders in the PC card and if "Auto Play" is checked the pro-

jector automatically starts to play slides at the first slide of the folder you

have selected.

A tool bar will appear when you press the MENU button on the remote

control or the projector cabinet or clicking with the right button of a mouse.

Play Jump

Drive

Delete

Drag

Setup

Stop Select

View

The tool bar includes the following buttons:

Drag ...........Drags to move the tool bar.This is available for USB mouse

operation only.

Prev ............Returns to the previous slide or folder. Or this lets you

play slides back in reverse.

Next ............Advances to the next slide or folder. Or this lets you play

slides back.

E-65

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

Play ............Plays back automatically or manually depending on the

setting on Viewer Options of the menu.This allows you to

move on to the next slide when "Manual Play" is selected.

Stop............This allows you to stop Auto Play while you are playing

back and to resume playing from the selected slide or folder

when "Auto Play" is selected.

Jump ..........Displays a list of slides while you are playing back.

Select .........Displays a list of folders while you are playing back.

Drive...........Switches between PC Card slot and USB port (type A).

Setup..........Displays the Viewer Options dialog box on Page 2 of the

Setup dialog box.

Delete.........Deletes a captured slide(s) or all the captured slides in

the Capture - specific folder.

View ...........Hides the tool bar while you are playing back. Pressing

the MENU button or clicking with the right button of a

mouse shows it again.

NOTE: If no memory card is inserted in the PC CARD slot, there is no signal, and

a black, blue or logo background is displayed, depending on the setting.

Playback is stopped when SLIDE +/- button on the remote control or ̇̈ button

on the cabinet is pressed in Auto Play mode.

Up to 12 indexes can be displayed on the list of folders. The folder in the right

bottom is always a folder exclusively for captured images, but is only displayed

when images have been captured.

E-66

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

When the tool bar is not displayed:

Press the FOLDER LIST button or the SLIDE LIST button on the remote con-

trol to display folders or slides from a PC card in the projector's PC Card slot.

Multi cursor (blue marks)

Folder

FOLDER

Folder

02 : 0001 / 0008

Current folder

number

Number of all slides

in folder

Current slide

number

Use the SLIDE +/- button to advance to

the next folder or return to the previous

folder.

Folder

SLIDE

Use the SLIDE +/- button to advance to the next slide or return to the

previous slide.

Slide(Table) cursor

(green marks)

Slide

02 : 0004 / 0008

E-67

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

NOTE: You can also use the ̇ and ̈ button on the remote control to select

folders or slides.

If you use the ̇ and ̈ button on the remote control for Viewer operation, press

the PJ button to switch to the Projector mode and the PJ button lights red.

Works as the Select button

SELECT

on the projector.

Lit red

Auto Play Mode

If the "Auto Play" option is selected in "Viewer Options" of the menu, any

given slide will start to play automatically.

You can also specify Auto Play Interval between 5 and 300 seconds.

Switching to Slides Directly from Other Input Modes

With this function it is possible to switch directly to a slide when the picture

of a VCR or computer is being projected.

Example: When conducting presentations using a combination of slides

and moving pictures from a VCR, etc., it is possible to switch from a

Viewer slide to the video picture then back to theViewer slide simply by

using the Viewer button.

NOTE: Even if you switch the current Viewer source to another source, the cur-

rent slide is retained. When you return back to the Viewer, you will get the slide

that has been retained.

The PC card editing operation cannot be performed from the projector. Do so

using the Dynamic Image Utility 2.0 software.

E-68

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

Viewing Digital Images

Digital images can be played with theViewer if the following conditions are

met:

• If the image can be stored on an MS-DOS format PC card

• If the image can be stored in a format supported by the Viewer. With

the Viewer, images on the card are searched for in directories and

images in JPEG or BMP format are recognized as slides. Searchable

directories are directories within two steps from the root directory,

and searchable images are images within the first 12 files in the di-

rectory. Only file and slide switching are possible.

NOTE: The maximum number of images recognized as slides within one directory

is 128.

Storing Images Displayed on the Projector on the PC

card (Capture)

The Capture features allows you to capture an image from a source that is

currently being displayed. The image is saved as JPEG in the PC card.

When you select Capture from the menu, you will get a tool bar. You can

capture an image directly using the tool bar when the menu is not dis-

played.

The tool bar includes the following buttons:

Capture

Drag

Freeze

Exit

Drive

Drag ...........Drags to move the tool bar by clicking on the blue part.

(for USB mouse operation only)

Capture ......Captures an image and saves it as a JPEG file on a PC

card.

Freeze ........Freezes and unfreezes images.

Drive...........Switches between PC Card slot and USB port (type A).

Exit .............Exits the Capture function.

E-69

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

NOTE:

Unless a PC card is inserted into the PC Card slot of the projector, the Cap-

ture feature is not available.

The "Card Error" display means that the free space of the PC card is insuffi-

cient for saving images. Make more space available on the card by erasing

unwanted images with your PC. The number of images that can be captured

depends on the size of the PC card.

Be sure not to turn off the power or remove the PC card while capturing an

image. Doing so could cause a loss of the data in the PC card or damage to

the card itself.

Preparations:

Insert the PC card into the card slot.

Insert the PC card so that the end with the insertion direction arrow on the

top goes in first.

* Press the eject button to eject the card.

1. Project the image you wish to store on the projector.

Capture

Drag

Freeze

Exit

Drive

2. Select the "Capture" from the Tools menu.

3. A tool bar will appear.

The tool bar includes the following buttons:

Drag ...........Drags to move the tool bar by clicking on the blue part (for

USB mouse operation only).

Capture ......Captures an image and save it as a JPEG file on a PC

card.

Freeze ........Freezes and unfreezes images.

Drive...........Switches between PC Card slot and USB port (type A).

E-70

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

Exit .............Exits the Capture function.Another option to exit the Cap-

ture function is to press MENU or CANCEL button on the

remote control or projector cabinet.

NOTE:

You can compress a captured file (JPEG) using the Capture Options in the Setup

dialog. See page E-97.

Captured images with higher resolution than the projector's native resolution

cannot be displayed correctly.

•

File size of the captured image varies depending on the resolution of an input

signal.

An hourglass indicating that an image is being captured appears on the

projector's display. Do not eject the PC card or turn off the projector's power

while this icon is displayed. Doing so will damage the PC card data. If the PC

card data is damaged, use a computer to repair the data.

•

Up to 12 indexes can be displayed on the list of folders. The folder in the right

bottom is always a folder exclusively for captured images, but is only dis-

played when images have been captured.

E-71

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

Deleting Captured Images

Using the Delete button on the tool bar for Viewer can delete captured

images.

Play Jump

Drive

Delete

Drag

Setup

Stop Select

View

To delete captured images:

1. Select Viewer and display a folder list of captured images.

2. Use

button to select the Capture folder [Cap] in the right bottom of

the screen.

3. Press the MENU button to display the tool bar.

4. Use the ̇ or ̈ button to select the Delete icon and press the ENTER

button or click with a mouse button.

Using the PC Card Files Fucntion (PC Card Files)

The PC Card Files function allows you to display a list of all the files stored

in the PC card so that you can select a file you want to display. You can

also sort files by file name or date, or display the file. Although a list of all

the files in the PC card is displayed, you can view files in idx, text, HTML,

JPEG and BMP format only. Selecting BMP and JPEG files automatically

switches to the Viewer source. See also page E-81.

NOTE: This option is not available for selection unless a PC card is inserted

properly.

Selecting "Execute" displays the file you selected.

When you select a JPEG or BMP file and press the Enter button on the

remote or the cabinet, or "Execute" on the above, you will get a toolbar.

This toolbar is used to return to the PC Card Files screen.

Drag ...........Drags to move the tool bar.(for USB mouse operation only)

Return ........Returns to the PC Card Files screen.

Close ..........Close the toolbar.

E-72

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU

Basic Menu Operation

Using the Menus

NOTE: The on-screen menu may not be displayed correctly while interlaced mo-

tion video image is projected.

1. Press the MENU button on the remote control or projector cabinet to

display the Basic, Advanced or Custom Menu.

NOTE: When using a USB mouse, click the mouse button to display the menu.

For other operations, do the same way as you use your PC mouse.

2. Press the SELECT ̆̄ buttons on the remote control or the projector

cabinet to highlight the menu for the item you want to adjust or set.

3. Press the SELECT ̈ button or the ENTER button on the remote control

or the projector cabinet to select a submenu or item.

4. Adjust the level or turn the selected item on or off by using SELECT ̇ or

̈ buttons on the remote control or the projector cabinet.

The on-screen slide bar will show you the amount of increase or decrease.

5. Changes are stored until you adjust it again.

ENTER .......Stores the setting or adjustments.

CANCEL ....Return to the previous screen without storing settings or

adjustments.

NOTE:You can close the main and sub menus simultaneously by pressing the

PJ button on the remote control to cancel the Projector mode.

6. Repeat steps 2-5 to adjust an additional item, or press the CANCEL but-

ton on the projector cabinet or the remote control to quit the menu dis-

play.

E-73

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Basic Menu Operation

Customizing the Menu

The Custom menu can be customized to meet your requirements. Select-

ing a menu item from the "Custom Menu Edit" list, allows you to custom

tailor the menu items to your needs.

1. Select "Custom Menu Edit" to display the "Custom Menu Edit" screen.

2. Use the SELECT ̆ or ̄ buttons to highlight your selection and press the

Enter button to place a check mark next to an option.

This action enables that feature. Press the Enter button again to clear the

check box.

If you select an item with a solid triangle ̈ and press the Enter button on

the remote control or the projector cabinet, you can enable all the items

within that submenu. Also you can turn on an item within the submenu

without placing a check mark on the main menu item.

NOTE: Up to 12 main menu items (within Custom Menu Edit, not including

submenu items) can be selected.

3. In order for the changes to take effect, use the SELECT ̇ or ̈ button on

the remote control or the projector cabinet to highlight "OK", then press

the Enter button. To cancel the changes, use the SELECT ̆ or ̄ buttons

to highlight "Cancel" and press the ENTER button.

To return to the factory default, select "Reset" then press the ENTER

button.

The default Custom Menu items are:

Source Select (RGB 1/2, Video, S-Video, Viewer and LAN), Picture, Vol-

ume, Image Options (Aspect Ratio), Picture Management, Projector Op-

tions (3D Reform, Menu, Setup, Screen and LAN Mode), Tools (Sleep

Timer, Capture, PC Card Files and ChalkBoard) and Help (Contents and

Information).

NOTE: Once you have selected OK on the Custom Menu Edit screen, you cannot

cancel the changes on the Menu screen. However, you can reedit the menu items

over again as described in the steps above.

E-74

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Basic Menu Operation

NOTE: If the "Advanced Menu" item has been selected on the Menu mode, you

get the "Confirmation Change Menu" upon completion of "Custom Menu" edit-

ing. In this case, selecting "Yes" then "Enter" will close all the menus and apply

the changes from the Advanced menu to the Custom Menu. If you select "No" then

"Enter" functions, then all menu items will return to the Advanced menu, but your

changes will still be available within the "Custom Menu" selection. To display the

previously tailored Custom Menu, select "Custom Menu" from the "Menu Mode".

An item "To Advanced Menu" will be added to the bottom of the Custom

Menu.

Selecting this item and pressing the ENTER button will display the "Ad-

vanced Menu" features.

E-75

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Basic Menu Operation

Menu tree

Advanced Menu

Source Select

Picture

RGB1

RGB2

Video

S-Video

Viewer

LAN

Volume

User1

Image Options

Picture Management

Projector Options

Tools

User2

User3

Entry List

Help

Picture

Brightness, Contrast, Color,

Hue, Sharpness

Factory Default

Volume

Aspect Ratio

4:3, Letter Box, Wide Screen, Crop / 4:3

Window, Letter Box, Wide Screen, 4:3 Fill

Top, Bottom, Left, Right

Horizontal, Vertical, Clock, Phase

Auto, Native

Blanking

Position/Clock

Resolution

Overscan

0%, 5%, 10%, 25%

Video Filter

Noise Reduction

Off, Less, More

Off, Low, Medium, High

Picture Management

Presentation, sRGB, Graphic, Video,

Movie, User 1, User 2, User 3, User 4

E-76

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Basic Menu Operation

Advanced Menu

Source Select

Picture

Cornerstone

Keystone

Horizontal, Vertical

Volume

Page 1

Image Options

Picture Management

Projector Options

Tools

3D Reform

Language

English, Deutsch,

Français, Italiano,

Español, Svenska

Setup

Screen

Help

LAN Mode

Password

Security

Menu Mode

Basic Menu,

Factory Default

Custom Menu,

Advanced Menu

Custom Menu Edit

Pointer 1-9

Setup

Page 1

Projector Pointer

Mouse Pointer

Pointer 1-9

Lamp Mode

Orientation

Normal, Eco

Menu Display Time Manual, Auto 5sec,

Auto 15sec,

Desktop Front, Ceiling Rear,

Desktop Rear, Ceiling Front

Blue, Black, Logo

Auto 45sec

Background

RGBOUT Terminal Last, RGB1, RGB2

Page 2

Closed Caption

Off, Caption1-4, Text1-4

Source Display

Message

On, Off

Menu Color Select Color, Monochrome

Page 2

Page 3 Signal Select

Viewer Options

Show Folder List

RGB1 RGB/Component, RGB,

Component, Scart

Auto Play, Manual Play, Interval

High Quality, Normal,

High Compression

Capture Options

Mouse Button

RGB2 RGB/Component, RGB,

Component

Right Hand, Left Hand

Video, Auto, NTSC3.58, NTSC4.43, PAL,

S-Video PAL-M, PAL-N, PAL60, SECAM

Sensitivity Fast, Medium, Slow

Page 4

Page 5

Auto Adjust, Auto Start, Power Management,

Power Off Confirmation, 3D Reform Save,

High Speed Fan Mode, Idle Mode,

Clear Lamp Hour Meter

Communication 4800, 9600, 19200,

Speed

38400

Default Source Last, Auto, Select (RGB1,

Select

RGB2, Video, S-Video,

Viewer, LAN)

Control Panel

Key Lock

Enable, Disable

E-77

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Basic Menu Operation

Screen Type 4:3, 16:9 / Position

LAN Mode

IP Address

Automatic

Advanced Menu

Source Select

Picture

3D Reform

Volume

Manual

IP Address,

Image Options

Picture Management

Projector Options

Tools

Subnet Mask,Gateway

Setup

Projector Name

DNS Configuration

Domain Name

Screen

LAN Mode

Password

Security

Help

Network Type

Mode

Factory Default

Infrastructure,

802.11 Ad Hoc,

Ad Hoc

Sleep Timer

Capture

Easy Connection

SSID

Channel

TX rate

PC Card Files

ChalkBoard

1-14

Automatic, 11M,

5.5M, 2M, 1M,

1M-2M-Automatic

Contents

Information

WEP

Disable, 64bit, 128bit

Key1-4

Key Select

Key1-4

Factory Default

All Data,

Current Signal

Mail

Alert Mail

Sender's Address

SMTP Server Name

Recipient's Address 1

Recipient's Address 2

Recipient's Address 3

Test Mail

Security

Enable, Disable, Keyword,

Use Protect key, Drive,

Read, Register, Delete

Logo

Status

IP Address

Subnet Mask

MAC Address

DHCP

Host Name Option

Client-identifier Option

E-78

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Basic Menu Operation

Menu Elements

Tab

Help Button

Title bar

Close Button

Radio button

Highlight

OK Button

Cancel Button

Solid triangle

Check box

Drag

Slide bar

Tool bar

Menu windows or dialog boxes typically have the following elements:

Title bar ........... Indicates the menu title.

Highlight .......... Indicates the selected menu or item.

Solid triangle ... Indicates further choices are available. A highlighted

triangle indicates the item is active.

Tab .................. Indicates a group of features in a dialog box. Selecting

on any tab brings its page to the front.

Radio button.... Use this round button to select an option in a dialog

box.

E-79

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Basic Menu Operation

Check box ....... Place a checkmark in the square box to turn the option

On.

Slide bar .......... Indicates settings or the direction of adjustment.

OK button ........ Press to confirm your setting.You will return to the pre-

vious menu.

Cancel button .. Press to cancel your setting.You will return to the pre-

vious menu.

Close button .... Click to close the window with saving changes. (USB

mouse only)

Help button...... Indicates that help about that feature is available (USB

mouse only).Press the Help button on the remote con-

trol to display help.

Toolbar ............ Contains several icons for specific tasks. It is also re-

ferred to as “launcher”.

Drag ................ Point the mouse here, and click and drag to move a

toolbar.

Entering Alphanumeric Characters by Using the Menu

Alphabet or numeric characters are used for your IP address or projector

name.To enter IP Address or projector name, use the software keyboard.

For using the software keyboard, see page E-137.

E-80

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU

Menu Descriptions & Functions

Source Select

Selecting a Source

Enables you to select a video source such as aVCR, DVD player, laser

disc player, computer or document camera depending on what is con-

nected to your inputs. Press the SELECT ̆̄ button on the projector

cabinet or on your remote control to highlight the menu for the source

you want to project.

RGB

Selects the computer connected to your RGB1, RGB2 or component

signal.

NOTE: An optional component cable (Component V or ADP-CV1 cable) is

needed for a component signal.

Video

Selects what is connected to your Video input-VCR, laser disc player,

DVD player or document camera.

S-Video

Selects what is connected to your S-Video input-VCR, DVD player, or

laser disc player.

NOTE: A frame may freeze for a brief period of time when a video is played

back in fast-forward or fast-rewind with a Video or S-Video source.

Viewer

This feature enables you to make presentations using a PC card that

contains captured images and slides created with the exclusive Dy-

namic Image Utility 2.0 contained in the CD-ROM. See the supplied

Application Guide for installing the Dynamic Image Utility 2.0.The start-

ing screen for theViewer varies depending on the settings of the Setup's

Page 2. See Setup on page E-96.

E-81

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

NOTE: Even if you switch the current Viewer source to another source, the cur-

rent slide is retained. When you return back to the Viewer, you will get the slide

that has been retained. A launcher will appear when you press the MENU button.

A press of the MENU button displays the toolbar; a press of the MENU

button again displays the Menu and hereafter each press of the MENU

button switches displaying between the Menu and the toolbar.

The launcher is a tool bar including the following buttons:

Play Jump

Drive

Delete

Drag

Setup

Stop Select

View

Drag ................ Drags to move the tool bar. (for USB mouse operation

only)

Prev................. Returns to the previous slide or folder.

Next ................. Advances to the next slide or folder.

Play ................. Plays back automatically or manually depending on the

setting onViewer Options of the menu.This allows you

to move on to the next slide when "Manual Play" is

selected.

Stop................. Stops Auto Play while you are playing back and to re-

sume playing from the selected slide or folder when

"Auto Play" is selected.

Jump ............... Displays a list of slides while you are playing back.

Select .............. Displays a list of folders while you are playing back.

Drive................ Switches between PC Card slot and USB port (type

A).

Setup............... Displays the Viewer Options dialog box on Page 2 of

the Setup dialog box.

Delete.............. Deletes a captured slide(s) or all the captured slides in

the selected folder.

View ................ Hides the tool bar while you are playing back. Clicking

with the right button of a mouse shows it again.

Provides access to controls for your image. Use the

SELECT button on the projector cabinet or the remote

control to highlight the menu for the item you want to

adjust.

E-82

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

LAN

Selects a signal from a LAN card plugged into the projector's card slot.

Entry List

Displays the list of the entry signals. Use the SELECT ̆̄ buttons on

your remote control or the projector cabinet to select the signal and

press the ENTER button on the remote control or the projector cabinet

to display the Entry Edit Command screen.

Using the Entry List

Making any adjustments to the current picture will automatically regis-

ter its adjustments to the Entry List.The registered signal can be loaded

any time from the Entry List.

NOTE: Up to 100 presets can be registered.

Entry Edit Command

You can edit signals on the Entry List.

Load: Enables you to select a signal from the list.

Store: Enables you to store the currently projected signal.

Cut: Enables you to remove a selected signal from the list and place it

on the "clipboard" in the projector.

Copy: Enables you to copy a selected signal from the list and place it

on the "clipboard" in the projector.

Paste: Enables you to paste the signal placed on the "clipboard" to any

other line of the list.To do this, select "Paste" and then select the line

number you want to paste to. Last press ENTER.

Edit: Enables you to change source names or add source names to

"More" in the Sorce Select.

Source Name:Enter a signal name.Up to 18 alphanumeric characters

can be used.

InputTerminal: Change the input terminal.RGB1 and RGB2 are avail-

E-83

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

able for RGB signal; Video and S-Video are available for composite

signal.

Source List: Set signal selection method.

Lock: Set so that the selected signal cannot be deleted when "All De-

lete" is executed.

Skip: Set so that the selected signal will be skipped during auto search.

When complete, select OK and press ENTER. To exit without storing set-

ting, select Cancel. Select "Source Name" and press ENTER to display

the Source Name Edit window.You can change source name on this win-

dow. Press [̄] to display the software keyboard, which you can enter al-

phanumeric characters. See page E-137 for the key function of the soft-

ware keyboard.

The following buttons are not available for the currently projecting signals:

1) The Cut and Paste buttons on the Entry Edit Command screen

2) The Input Terminal button on the Entry Edit screen

All Delete: This feature enables you to delete all the registered signals

in the Entry List.

NOTE: When all the signals in the Entry List are deleted, the currently pro-

jected signal will be also deleted except locked signals.

Select "Input Terminal" and press ENTER to display the Input Termi-

nal window.

E-84

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Picture (not available for Viewer and LAN)

Adjusting Brightness, Contrast, Color, Hue, and Sharpness

Brightness ....... Adjusts the brightness level or the back raster inten-

sity.

Contrast .......... Adjusts the intensity of the image according to the in-

coming signal.

Color ............... Increases or decreases the color saturation level (not

valid for RGB).

Hue ................. Varies the color level from +/- green to +/-blue.The red

level is used as reference.This adjustment is only valid

for Video and Component inputs (not valid for RGB).

Sharpness....... Controls the detail of the image for Video (Not valid for

RGB).

Volume

Controllling Volume

Adjusts the sound level of the projector speaker and AUDIO OUT.

E-85

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Image Options

Selecting Aspect Ratio (not available for Viewer and LAN)

Aspect Ratio allows you to select the best Aspect mode to display your

source image.

When screen size 4:3 is selected for the source, the following selec-

tions will display:

4:3 ................... Standard 4:3 aspect

Letter Box........ Reduced to display the true aspect with black borders

on top and bottom

Wide Screen ... Left & Right stretched with black borders on top and

bottom

Crop ................ Left & Right streched.

Left & Right sides cut. Available for 4:3 only.

When screen size 16:9 is selected for the source, the following selec-

tions will display:

4:3 Window ..... Reduced to display the true aspect with black borders

on right and left

Letter Box........ Standard 16:9 aspect

Wide Screen ... Left and right streched to display the true aspect

4:3 Fill ............. Stretched to display in 16:9 aspect ratio

NOTE: You can adjust image positions vertically for source with black borders.

See page E-101 for setting image positions.

Please note that using this projector for the purpose of commercial gain or the

attraction of public attention in a venue such as a coffee shop or hotel and em-

ploying compression or expansion of the screen image with a "Aspect Ratio" or

"Screen" setting may raise concern about the infringement of copyrights which

are protected by copyright law.

E-86

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

NOTE: During 3D Reform adjustment, "Aspect Ratio" may not be available.

Should this happen, first reset the 3D Reform data and then do setting again.

Second repeat the 3D Reform adjustment.

Changing the aspect ratio can limit 3D Reform in its adjustable range.

Input

Signal

Screen

Type

Squeeze

4:3

Letter Box

4:3 Screen

Letter Box

Crop

Wide Screen

16:9 Screen

4:3 Fill

4:3 Window

Wide Screen

Masking Unwanted Area (Blanking)

This feature allows you to mask any unwanted area of the screen im-

age.

Adjust the Top, Bottom, Left or Right blanking with the SELECT ̇ or ̈

button.

Adjusting Position and Clock

This allows you to manually adjust the image horizontally and verti-

cally, and adjust Clock and Phase.

Horizontal/Vertical Position:

........................ Adjusts the image location horizontally and vertically

using the SELECT ̇ and ̈ buttons. This adjustment

is made automatically when the Auto Adjust is turned

on. See "Auto Adjust" on page E-98 for turning on or

off the Auto Adjust feature.

E-87

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Clock ............... Use this item to fine tune the computer image or to

remove any vertical banding that might appear. This

function adjusts the clock frequencies that eliminate

the horizontal banding in the image.

Press the SELECT ̇ and ̈ buttons until the banding

disappears. This adjustment may be necessary when

you connect your computer for the first time. This ad-

justment is made automatically when the Auto Adjust

is turned on.

Phase .............. Use this item to adjust the clock phase or to reduce

video noise, dot interference or cross talk. (This is evi-

dent when part of your image appears to be shimmer-

ing.) Use the SELECT ̇ and ̈ buttons to adjust the

image.

Use "Phase" only after the "Clock" is complete. This

adjustment is made automatically when the Auto Ad-

just is turned on.

Selecting Resolution

This allows you to activate or deactivate the Advanced AccuBlend fea-

ture.

Auto ................. Turns on the Advanced AccuBlend feature. The pro-

jector automatically reduces or enlarges the current

image to fit the full screen.

Native .............. Turns off the Advanced AccuBlend feature. The pro-

jector displays the current image in its true resolution.

See "Auto Adjust" on page E-98 for turning on or off

the Auto Adjust feature.

E-88

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

NOTE:

When "Resolution" is set to "Native", "Overscan", "3D Reform", "Aspect

Ratio" and "Screen" are not available.

While you are displaying an image with higher resolution than the

projector’s native resolution, "Resolution" is not available.

Selecting Overscan Percentage

Select overscan percentage (0%, 5%, 10% and 25%) for signal.

NOTE: When "Resolution" is set to "Native", this feature is not available, and

the stored settings and adjustments are invalid.

NOTE: When "4:3 Fill" or "Crop" is selected in "Aspect Ratio", this feature is

not available.

Selecting Video Filter Level (not available for Video, Viewer and LAN)

This function reduces video noise.

Off ................... The filter is removed.

Less ................ The low-pass filter is applied partially.

More ................ The low-pass filter is applied fully.

Selecting Noise Reduction Level (not available for RGB, Viewer and LAN)

Select one of the three levels for reducing video noise: Low, Medium or

High.

NOTE: The lower the Noise Reduction level, the better the image quality by

way of higher video bandwidth.

E-89

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Picture Management

This option allows you to adjust neutral tint for yellow, cyan or magenta.

There are 5 factory presets optimized for various types of images, or

you can set 4 user adjustable settings.

Presentation .... Recommended for making a presentation using a

PowerPoint file

sRGB .............. Standard color values

Graphic ........... Recommended for graphics

Video ............... Recommended for regular picture such asTV program

Movie .............. Recommended for movie

User 1-4 .......... User adjustable

NOTE: When "sRGB", "Graphic", "Video" or "Movie" is selected, the bright-

ness decreases slightly when compared to "Presentation." This is not a mal-

function.

User Adjust (when using User 1 to 4)

When selecting one of four user adjustable presettings (User 1 through 4),

the submenu will be displayed.

You can customize each gamma or color. To do so, first select [Setting]

and press the ENTER button, and then proceed the following steps.

Selecting Gamma Correction Mode

Use the ̇ or ̈ buttons to choose one mode from three options.

Each mode is recommended for :

Dynamic .......... For true color reproduction of natural tones

Black Detail ..... For dark portions of a picture

Natural ............ Normal settings

E-90

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Selecting Color Correction

Adjusts red, green, blue, yellow, magenta, cyan and color gain each

independently to correct the tint on whole screen.

Selecting White Peaking

Adjust the brightness of the white areas by using the slide bar. As the

picture becomes dim, it looks more natural.

Adjusting Color Temperature and White Balance

This feature adjusts the color temperature using the slide bar.

Checking "Color Temperature" enables the color temperature slide bar

and disables the “White Balance” button.

Press the White Balance button to access the Contrast/Brightness ad-

justment for each R, G, and B.

NOTE: "Color Temperature" and "White Balance" are a trade-off.

The White Balance is not available for Viewer and LAN.

NOTE: When "Presentation" is selected, the available items are "Gamma"

and "White Balance" only.

E-91

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Selecting Base Setting

This feature allows you to use color correction or gamma values as

reference data to optimize for various types of images.You can select

one of the following five settings.

• Presentation

• Graphic

• Video

• sRGB

• Movie

Projector Options

Using 3D Reform

This feature corrects trapezoidal distortion so that the projected image

is rectangular.

Two options are available for correcting procedures.

You can save adjustment settings by using the 3D Reform Save option

on Setup (See page E-99).

Cornerstone

See page E-44

Keystone

1. Press the SELECT ̇̈ button to adjust the horizontal keystone.

2. Press the SELECT ̆̄ button to select "Vertical".

3. Press the SELECT ̇̈ button to adjust the vertical keystone.

4. After completing, press the ENTER button. This will return to the

menu screen.

When "Resolution" is set to "Native", "Cornerstone" and "Keystone"

are not available.

E-92

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Allows you to set preferences for the on-screen menu. Press "OK" to

save your changes for all the features of Page 1 and Page 2.

[Page1]

Selecting Menu Language [Language]:

You can choose one of seven languages for on-screen instructions.

The options are: English, German, French, Italian, Spanish, Swed-

ish and Japanese.

Selecting Menu Mode [Menu Mode]:

This feature allows you to select 3 menu modes: Advanced Menu,

Custom Menu and Basic Menu.

Advanced Menu

........................ This is the menu that contains all the available menus

and commands.

Basic Menu ..... This is the basic menu that contains minimum essen-

tials of menus and commands.

Custom Menu.. This is the menu that you can customize using the

Custom Menu Edit to fit your needs.

Customizing the Menu:

See page E-74 for instructions about how to customize the Menu.

Selecting a Projector Pointer Icon [Projector Pointer]:

This enables you to select one of nine different Pointer icons for the

"Pointer" button on your remote control.

After moving your Pointer icon to the area you want on the screen,

press the Magnify button on the remote control to enlarge the se-

lected area on the screen. See page E-54 for more details.

NOTE: There may be cases where the Pointer function is not available (ex.

a non-interlace signal at 15kHz such as video game.)

E-93

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Selecting a Mouse Pointer Icon [Mouse Pointer]:

This option enables you to select one of nine different mouse point-

ers when using a USB mouse.

Selecting Menu Display Time :

This option allows you to select how long the projector waits after

the last touch of a button to turn off the menu.

The preset choices are "Manual", "Auto 5 sec", "Auto 15 sec", and

"Auto 45 sec". The "Auto 45 sec" is the factory preset.

Manual ............ The menu can be turned off manually.

Auto 5 sec ....... The menu will automatically be turned off in 5 seconds

if no buttons are pressed within 5 seconds.

Auto 15 sec ..... The menu will automatically be turned off in 15 sec-

onds if no buttons are pressed within 15 seconds.

Auto 45 sec ..... The menu will automatically be turned off in 45 sec-

onds if no buttons are pressed within 45 seconds.

[Page 2]

Turning On / Off Source Display [Source Display]:

This option turns on or off input name display such as RGB1/2,

Video, and No Input to be displayed in the top right corner of the

screen.

Turning On / Off Message [Message]:

This option turns on and off messages for lamp life warning, 3-minute

before power off time and "Please wait a moment".

Selecting Menu Color [Menu Color Select]:

You can choose between two color modes for menu color:color and

monochrome.

E-94

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Setup

Enables you to set operating options.

Press "OK" to save your changes for all the features of Page 1, Page 2,

Page 3, Page 4 and Page 5.

[Page 1]

Setting Lamp Mode to Normal or Eco [Lamp Mode]:

This feature enables you to select two brightness mode of the lamp:

Normal and Eco modes. The lamp life can be extended up to 3000

hours by using the Eco mode.

Normal Mode .. This is the default setting (100% Brightness).

Eco Mode ........ Select this mode to increase the lamp life (80% Bright-

ness).

Selecting Projector Orientation [Orientation]:

This reorients your image for your type of projection. The options

are: desktop front projection, ceiling rear projection, desktop rear

projection, and ceiling front projection.

Selecting a Color or Logo for Background [Background]:

Use this feature to display a blue/ black screen or logo when no

signal is available. The default background is blue.You can change

the logo screen using the PC Card Files feature. See pages E-59

and 118.

E-95

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Setting RGB 1 or 2 for RGB OUT [RGBOUT Terminal]

This option allows you to determine which RGB source is output

from the RGBOUT connector during Idle mode.

Last ............ The signal from the last RGB input will be output to the

RGBOUT connector.

RGB 1 ........ The signal from RGB IN1 will be output to the RGBOUT

connector.

RGB 2 ........ The signal from RGB IN2 will be output to the RGBOUT

connector.

NOTE: The AUDIO OUT mini jack will not output sound during the Idle

mode.

Setting Closed Caption

This option sets several closed caption modes that allows text to be

superimposed on the projected image.

CAPTION 1-4 ....... Text is superimposed.

TEXT 1-4.............. Text is displayed in full screen.

OFF ...................... This exits the closed caption mode.

[Page 2]

Setting Viewer Options [Viewer Options]

Show Folder List:

If this option is checked, when the Viewer source is selected on the

projector, the folder lists will be displayed and allows you to select

the presentation from a PC card.

Auto Play:

If this option is checked, when the Viewer source is selected on the

projector any given slide will start to play automatically.

E-96

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Auto Play Interval:

You can specify interval time between 5 and 300 seconds.

NOTE: The Auto Play Interval time set on “Slide Show Settings” of the

Dynamic Image Utility 2.0 overrides the one set here.

Manual Play:

Views a slide manually when the Viewer source is selected.

Selecting Capture Options [Capture Option]: (available for JPEG only)

These options are used for the Capture function that you can select

from Tools. You have three options for JPEG compression quality:

High quality, Normal and High Compression.

High Quality ................... Gives quality of JPEG a priority.

Normal ........................... Gives normal JPEG quality.

High Compression ......... Gives compression a priority.

Setting Mouse Button and Sensitivity [Mouse]:

This option lets you to change your USB mouse settings.The mouse

settings feature is available for USB mouse only. Choose the set-

tings you want:

Mouse Button................. "Right Hand" or "Left Hand"

Mouse Sensitivity ........... "Fast", "Medium" or "Slow"

E-97

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

[Page 3]

Selecting Signal Format [Signal Select]

RGB1/2:

Allows you to choose "RGB" for an RGB source such as a com-

puter, or "Component" for a component video source such as a DVD

player. Normally select "RGB/Component" and the projector auto-

matically detects an either incoming signal. However there may be

some component signals that the projector is unable to detect. If

this is the case, select "Component".Select "Scart" in RGB 1 for the

European Scart.

VIDEO and S-VIDEO:

This feature enables you to select composite video standards manu-

ally. Normally select "Auto". Select the video standard from the pull-

down menu. This must be done for Video and S-Video separately.

[Page 4]

Enabling Auto Adjust [Auto Adjust]:

When "Auto Adjust" is set to "On", the projector automatically deter-

mines the best resolution for the current RGB input signal to project

an image using NEC's Advanced AccuBlend Intelligent Pixel Blend-

ing Technology.

The image can be automatically adjusted for position and stability;

"Horizontal Position", "Vertical Position", "Clock", "Phase", and

"Resolution".

On .............. Automatically adjusts image "Horizontal Position", "Ver-

tical Position", "Clock", "Phase" and "Resolution".

Off .............. User can adjust the image display functions ("Horizon-

tal Position", "Vertical Position", "Clock", "Phase" and

"Resolution") manually.

E-98

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Enabling Auto Start [Auto Start]:

Turns the projector on automatically when the power cable is in-

serted into an active power outlet and the main power switch is

turned on. This eliminates the need to always use the "Power" but-

ton on the remote control or projector cabinet.

Enabling Power Management [Power Management]:

When this option is on and there is no input for five minutes or more,

the projector will automatically turn itself off.

Enabling Power Off Confirmation [Power Off Confirmation]:

This option determines whether a confirmation dialog for turning off

the projector will appear or not.

NOTE: When the confirmation message is displayed, you must be in the

Projector mode to operate your projector using the remote control. If not,

press the PJ button on the remote control to change your projector to the

Projector mode. The button lights to indicate that you are in the Projector

mode.

Enabling Horizontal and Vertical Keystone Correction Save:

[3D Reform Save]

This option enables you to save your current 3D Reform settings.

Saving your change once affects all sources.The changes are saved

when you turn off the projector.

Enabling High Speed Fan Mode [High Speed Fan Mode]:

This option allows you to select two modes for fan speed:high-speed

mode and normal speed mode.

When you wish to cool down the temperature inside the projector

quickly, check this box.

NOTE: Enable High-Speed Fan mode if you continue to use the projector

for consecutive days.

E-99

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Enabling Idle Mode [Idle Mode]:

The projector has two standby modes: Standby and Idle.

Standby is the mode that allows you to put the projector in the standby

condition which consumes less power than the idle mode. The pro-

jector is preset for Standby at the factory.

When this check box is turned on, you allow the RGB OUT connec-

tor to output RGB signal during Idle mode.

NOTE:

The RGB OUT connector will not output signal during the Standby mode.

Via the serial interface the projector can be turned on from your PC

using Dynamic Image Utility 2.0 during the Standby or Idle mode. On

the LAN connection the projector can be controlled or monitored

from your PC using Dynamic Image Utility 2.0 only in the Idle mode.

The HTTP server functions are not available during Standby mode.

Clearing Lamp Hour Meter [Clear Lamp Hour Meter]:

Resets the lamp clock back to zero. Pressing this button appears a

confirmation dialog box. To reset the lamp usage hour, press "OK".

NOTE: The projector will turn off and go into standby mode after 2100

hours (up to 3100 hours in Eco mode) of service. In this condition you

cannot clear the lamp hour meter on the menu. If this happens, press the

"Help" button on the remote control for ten seconds to reset the lamp clock

back to zero. Do this only after replacing the lamp.

[Page 5]

Selecting Communication Speed [Communication Speed]:

This feature sets the baud rate of the PC Control port (Mini DIN 8

Pin). It supports data rates from 4800 to 38400 bps.

The default is 38400 bps. Select the appropriate baud rate for your

equipment to be connected (depending on the equipment, a lower

baud rate may be recommended for long cable runs).

Selecting Default Source [Default Source Select]:

You can set the projector to default to any one of its inputs each

time the projector is turned on.

E-100

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Last ............ Sets the projector to default to the previous or last ac-

tive input each time the projector is turned on.

Auto............ Searches for an active source in order of RGB1 →

RGB2 → Video → S-Video → Viewer → RGB1 and

displays the first found source.

Select ......... Displays the selected source input every time the projec-

tor is started up. Select an input from the pull-down menu.

Disabling the Cabinet Buttons [Control Panel Key Lock]:

This option turns on or off the Control Panel Key Lock function.

NOTE:

This Control Panel Key Lock does not affect the remote control and the

PC Control functions.

When the cabinet buttons are disabled, pressing and holding the CAN-

CEL button for about 10 seconds will change the setting to enabled.

Selecting Aspect Ratio and Position for Screen [Screen]

Screen Type:

Select either 4:3 Screen or 16:9 Screen for the screen to be used.

See also "Aspect Ratio" on page E-86.

NOTE: When "Resolution" is set to "Native", this selection is inactive.

Position:

This feature adjusts the vertical position of the image when viewing

video with an aspect ratio selected.

When some aspect ratios are selected in Image Options, the image

is displayed with black borders on the top and bottom.

You can adjust the vertical position between top and bottom.

NOTE: This option is available only when "16:9" is selected in Screen Type.

NOTE: During 3D Reform adjustment, "Screen Type" and "Screen Position"

may not be available. To make available, first reset the 3D Reform data and then

do settings again. Secondly repeat the 3D Reform adjustment. Changing "Screen

Type" and "Screen Position" can limit 3D Reform in its adjustable range.

E-101

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Setting LAN Mode

This feature allows you to set various setting items when the projector is

used on your network.

Consult with your network administrator about these settings.

NOTE: A LAN card is required for LAN connection; NEC's optional wireless LAN

card is available. For more information on inserting or ejecting a LAN card, see

pages E-63 and 64.

CAUTION: Make sure that the LAN card is removed during Standby mode

(NOT Idle mode) or with the main power off.

Failure to do so may cause damage to the PC card.

CAUTION: Do not use CompactFlash type cards except for flash memory

cards. Using a CompactFlash card with the help of a PC card adapter

could cause damage to the CompactFlash card.

NOTE: LAN card is not available when a PC card is used for the Viewer function.

Viewer is not available when LAN card is used for LAN connection.

IP Address

An IP address can be automatically assigned to this projector by your

DHCP server. If your network does not automatically assign IP address,

ask your network administrator for an address, and then register it manu-

ally.

E-102

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Automatic ........ Automatically assigns an IP address to the projector

from a DHCP server.

Manual ............ Provides a space for you to register the IP address or

subnet mask number obtained from your network ad-

ministrator.

IP Address ...... Set your IP address. Press

keyboard and type in 12 numeric characters.

Subnet Mask ... Set your subnet mask number. Press to display the

software keyboard and type in 12 numeric characters.

to display the software

Projector Name

........................ Specify a unique projector name. Press

to display

the software keyboard and type in. Up to 16 alphanu-

meric characters can be used.

Gateway .......... Set the default gateway of the network connected to

the projector.Press to display the software keyboard

and type in 12 numeric characters.

Checking this box will make the set default route valid.

When data is sent from the LAN card, the transfer lo-

cation will be searched according to the previously set

routing information; however, when the transfer loca-

tion has not been found as a result of the search, the

data will be sent to the device that holds the IP ad-

dress set here.The IP address that is set here must be

one that can be identified by a search of the routing

information.

DNS Configuration

........................ Type in the IP address of DNS server on the network

connected to the projector. 12 numeric characters are

used.

Domain Name . Type in domain name of the network connected to the

projector. Up to 60 alphanumeric characters can be

used.

E-103

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Network Type (required for wireless only)

Mode:

Select communication method when using wireless LAN.

Infrastructure ... Select this option when communicating with one or

more equipment connected to the wireless or wired

LAN network via an access point.

802.11 Ad Hoc Select this option when using the wireless LAN to com-

municate with a computer in a one-to-one correspon-

dence. This is a method that meets the IEEE802.11

wireless standard.

Ad Hoc ............ Select this option when using the wireless LAN to com-

municate with a computer in a one-to-one correspon-

dence.

Easy Connection

........................ This allows you to easily set up wireless LAN connec-

tion.See the supplied Software Utility Installation Guide

for more information.

E-104

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

SSID (Network name):

Enter an identifier (SSID) for wireless LAN when selecting [Infrastruc-

ture] or [802.11 Ad Hoc] in [Mode]. Communication can be done only

with equipment whose SSID matches SSID for your wireless LAN. Up

to 32 alphanumeric characters can be used.

NOTE: To disable SSID, select a space (null) or "ANY"(All caps).

Channel:

Set this option when selecting [802.11 Ad Hoc] or [Ad Hoc] in [Mode].

Select a channel number from the pull-down list. The channel must

match for all wireless devices communicating on your wireless LAN.

NOTE: Channels in the pull-down list are different depending on which coun-

try you live in.

TX rate:

Select a wireless transmission speed. Normally leave it as Automatic.

Try another transmission speed when the connection fails.

E-105

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

WEP (for Wireless only)

Select this option whether using the WEP (Wired Equivalent Privacy)

key for encryption or not. To use encryption, specify WEP key.

Disable ............ Will not turn on the encryption feature.Your communi-

cations may be monitored by someone.

64bit ................ Uses 64-bit datalength for secure transmission.

128bit .............. Uses 128-bit datalength for secure transmission. This

option will increase privacy and security when com-

pared to use of 64bit datalength encryption.

NOTE: The WEP settings must be the same as communication devices such as PC

or access point in your wireless network. When you use WEP, your image trans-

mission speed will slow down.

Key Select:

Selects one key from the four keys below when selecing [64bit] or [128bit]

in [WEP].

E-106

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Key1-4:

Enter encryption key when selecting [64bit] or [128bit] in [WEP].

Up to 5 characters can be set in 64 bit and up to 13 characters in 128

bit. Press the “HEX” button to change to “ASCII” to set the key in ASCII

digit.You can toggle this button between “ASCII” and “HEX”.

The key can also be set in hexadecimal digit.

* Hexadecimal uses 0 to 9 and A to F.

* Up to 10 characters can be set in 64 bit and up to 26 characters in

128 bit.

Mail

NOTE: To the Mail Alert feature on wireless LAN connection, select "Infrastruc-

ture" for "Mode" in "Network Type."

"Test Mail" is available only when there is a LAN card in the PC card slot of the

projector.

Alert Mail:

Checking this box enables Alert Mail feature.

This option notifies your computer of an error message via e-mail when

using wireless or wired LAN. The error message will be notified when

the projector lamp has reached the end of its usable life or an error

occurs in the projector.

E-107

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Sample of a message sent from the projector:

The lamp is at the end of its usable life. Please replace the lamp.

Projector Name: X X X X

Lamp Hour Meter: xxxx [H]

Projector Usage: xxxxxx [H]

Sender's Address:

Specify the senders address. Use the Software keyboard. Up to 60

alphanumeric and symbols characters can be used. See "Using Soft-

ware Keyboard" in Appendix for more details.

SMTP Server Name:

Type in the SMTP server name to be connected to the projector. Up to

60 alphanumeric characters can be used.

Recipient's Address 1 to 3:

Type in your recipient's address. Up to 60 alphanumeric and symbols

characters can be used.

Test Mail:

Send a test mail to check if your settings are correct.

NOTE: If you entered an incorrect address in a test, you may not receive an

Alert mail. Should this happen, check if the Recipient's Address is correctly

set.

NOTE: Unless any one of the "Sender's Address", "SMTP Server's Name" or

"Recipient's Address 1-3" is selected, "Test Mail" is not available.

NOTE: Be sure to highlight “OK” and press the ENTER button before execut-

ing “Test Mail”.

E-108

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Status

Displays the status of the LAN settings.

IP Address ...... Indicates the IP address of the projector.

Subnet Mask ... Indicates the subnet mask of the projector.

Gateway .......... Indicates the gateway of the network connected to the

projector.

MAC Address .. Indicates the MAC address of the LAN card.

Reconnect ....... Use this button to connect the projector to a network.

E-109

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

DHCP

Depending on your network environment, acquiring an IP address from a

DHCP server may not be possible.

Should this happen, consult your network administrator to make changes

to the following settings.

Host Name option

Select whether or not to add option hostname for DHCP.

None ......................... Not add

Request..................... Add at the time of DHCP_REQUEST.

Discover/Request ...... Add at the time of DHCP_DISCOVER and

DHCP_REQUEST.

Host Name

Type in a hostname.This field is available only when “Request” or “Dis-

cover/Request.”

E-110

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Client-identifier option

Select whether or not to add option client identifier for DHCP.

None ......................... Not add

Request..................... Add at the time of DHCP_REQUEST.

Discover/Request ...... Add at the time of DHCP_DISCOVER and

DHCP_REQUEST.

Use MAC address

Turn on to use MAC address for Client-identifier.

Client-identifier

Type in a client identifier.

E-111

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Setting a Password

A password can be set for your projector to avoid operation by an unau-

thorized person.

There are two password options: one for menu and the other for logo.

When a password is set, doing any one of the following four operations will

display the Password input screen.

For Menu:

* Changing the menu to Advanced

* Editing the custom menu

For Logo:

* Changing the background

* Changing the logo data in PC Card Files

Procedures for Password setting apply to both Menu and Logo.

Entry

To assign your password:

NOTE: Up to 15 alphanumeric characters can be assigned.

1. Type a password.

Highlight "Entry" and press the ENTER button.

The "Enter the Password screen" will be displayed.

Make sure that [̄] is highlighted and then press the ENTER button.

The Software keyboard appears. Use the Software keyboard to type a password and

then highlight "OK" on the “Enter the Password” screen and press the ENTER button.

The [Confirm Password] screen will be displayed.

2. Type the same password again. Highlight "OK" on the “Enter the Password” screen

and press the ENTER button.

Your password will be assigned.

E-112

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Delete

To delete your password:

1. Highlight [Delete] and press the ENTER button. The "Current Password" screen will

be displayed.

2. Use the Software keyboard to type your password. Highlight "OK" on the “Current

Password” screen and then press the ENTER button.

Your password will be deleted.

In case you forget your password, follow the steps below to delete it.

1. Select the Advanced menu from the Basic menu.The "Password" entry screen will be

displayed.

2. Use the Software keyboard to type "1111".

Highlight "OK" on the “Password” entry screen and then press the ENTER button.

The "Password Warning!!" message will be displayed.

3. Use the Software keyboard to type "3333".

Highlight "OK" on the “Password” entry screen and then press the ENTER button.

The "Password Warning!!" message will be displayed.

4. Use the Software keyboard to type "5555".

Highlight "OK" on the “Password” entry screen and then press the ENTER button.

The "Delete Password. Are you sure? Yes/No" dialog box will be displayed.

5. Use the SELECT ̇ or ̈ button to highlight "Yes" and press the ENTER button.

Your password will be deleted.

E-113

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Security

The Security function enables you to protect your projector so that the

projector will not project a signal unless you enter a keyword.There is also

an option to lock the projector by using a registered PC card as a protect

key. Once you have registered your PC card as a protect key, you are

required to insert the registered PC card into the PC card slot of the pro-

jector each time you turn on the projector. You can enable the Security

function by using a keyword only.

Enable/Disable .......... This turns the Security function on or off.

Keyword .................... Enter an appropriate keyword when you use the

Security function.

(Up to 10 characters can be used.)

The Security function is available only when your

keyword is entered.

Use Protect key ......... Check this box to lock your projector when us-

ing a PC card. To use a keyword without a PC

card, do not check this box.

Drive.......................... Switches between PC Card slot and USB port

(type A).

Read ......................... Reads data of a PC card.

The Security function is not available unless at

least one PC card is registered. (if the “Use Pro-

tect key” check box is selected)

Up to 5 PC cards can be registered.

Delete........................ Deletes data of a registered PC card.

E-114

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

To set up a keyword to enable the Security function without using a regis-

tered PC card

1. Use the SELECT ̆̄ button to select “Keyword” and use the software

keyboard to enter a keyword.

NOTE: Please make a note of your keyword.

2. Use the SELECT ̆̄ button to select “Enable” and use the SELECT

̆̄ button to select “OK”, then the Security function will be enabled. An

“Are you sure?” message will appear. Use the SELECT ̇̈ button and

press the ENTER button.

The Security function takes effect.

To register a PC card as a protect key

1. Insert a PC card into the PC card slot of the projector.

2. Use the SELECT ̆̄ button to select “Use Protect key” and press the

ENTER button. A check mark will be placed.

3. Use the SELECT ̆̄ button to select "Read" and press the ENTER but-

ton.

Data of the PC card will be read into the projector.

4. Use the SELECT ̆̄ button to select "Register" and press the ENTER

button.

Downloaded data will be registered and be displayed in the list window.

5. Use the SELECT ̆̄ button to select "Keyword" and use the software

keyboard to enter a keyword.

NOTE: To use a PC card as a protect key, you must also set up a keyword. Please

make a note of your keyword.

This completes registration of your PC card.

To enable Security, use the SELECT ̆̄ button to select "Enable" and

use the SELECT ̆̄ button to select "OK" and "Security function will be

enabled. An “Are you sure?" message will appear. Use the SELECT ̇̈

button and press the ENTER button.

The Security function takes effect.

E-115

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

To turn on the projector when Security is enabled (when using your key-

word only)

1. Press and hold the POWER button for a minimum of two seconds.

The projector will be turned on and display a message to the effect that

the projector is security-protected.

2. Select [Projector Options] → [Security] from the menu and press the EN-

TER button.

The Release Code input screen will be displayed.

3. Enter your keyword in the Release Code input screen.

You can view the projected image.

NOTE: Do not forget your keyword. However, if you forget your keyword, NEC or

your dealer will provide you with your Release Code. See more information at the

end of this section.

To turn on the projector when Security is enabled (when using a PC card

as a protect key)

1. Insert your registered PC card into the PC card slot.

2. Press and hold the POWER button for a minimum of two seconds.

The projector will turn on and then recognize the PC card. Once the im-

age has been projected, it will stay on without the PC card.

•

The security disable mode is maintained until the main power is turned

off (by setting the main power switch to “ć” or unplugging the power

cord).

In the following cases you will be asked to check the protect key or

input the keyword:

(1) When “OK” is selected at an image for which security is set and the

power is turned off then back on

(2) When the main power is turned off then back on while the security

function is enabled

(3) When you attempt to display an image for which security is set while

the security function is enabled

•

Blanks (spaces) cannot be used in the Keyword section.

E-116

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

To delete PC card data you registered

1. Use the SELECT ̆̄ button to select "Delete" and use the SELECT ̇

button to select the list window.

2. Use the SELECT ̆̄ button to select the PC card data you wish to de-

lete.

3. Press the SELECT ̈ button to select "Delete" and press the ENTER

button.

The PC card data will be deleted.

If you've lost your registered PC card, proceed as follows:

NOTE: NEC or your dealer will provide you with your Release Code in ex-

change for your registered keyword and Request Code. See more information

at the end of this section.

1. Press and hold the POWER button for a minimum of two seconds.

The projector will be turned on and display a message to the effect that

the projector is security-protected.

2. Select [Projector Options] → [Security] from the menu and press hte EN-

TER button.

The Release Code input screen will be displayed as well as your Request

Code (24 alphanumeric characters).

3. Enter your Release Code in the Release Code Input screen.

The projector will turn on.

If the projector is turned on by entering the Release Code, your Secu-

rity will be disabled.

NOTE:

* Some types of PC cards cannot be registered as your protect key.

* It is recommended that you register two or more PC cards in case you lose or

damage your registered PC card.

* Formatting your registered PC card will disable your protect key function.

NOTE:

For additional information visit:

US : http://www.necvisualsystems.com

Europe : http://www.nec-europe.com/

Global : http://www.nec-pj.com/

E-117

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Tools

Provides tools for setting sleep timer, capturing images, displaying files or

changing your background logo in a PC Card and drawing.

NOTE: The "Capture" and "PC Card Files" features are required for a PC card.

Using Sleep Timer

1. Select your desired time between 30 minutes and 16 hours: Off, 0:30, 1:00,

2:00, 4:00, 8:00, 12:00, 16:00.

2. Select “Set” and press the ENTER button on the remote control.

3. The remaining time starts counting down.

4. The projector will turn off after the countdown is complete.

NOTE:

•

To cancel the preset time, set "Off" for the preset time or turn off the power.

When the remaining time reaches 3 minutes before the projector is turned off,

the "Projector will turn off in 3 minutes" message will be displayed on the

bottom of the screen.

Using Capture

Allows you to capture an image from a source that is currently being dis-

played. The image is saved as JPEG in the PC card. When you select

Capture from the menu, you will get a tool bar.You can capture an image

directly using the tool bar when the menu is not displayed.

See page E-69.

Using PC Card Files

The PC Card Files feature allows you to display a list of all the files stored

in the PC card so that you can select a file you want to display. You can

also sort files by file name or date, or display the file. See page E-59.

E-118

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

Changing Background Logo:

You can change the default background logo using the PC Card Files

feature.

NOTE: File size must be 256KB or less. Other file formats than JPEG and

BMP are not available. See page E-59.

Using ChalkBoard

The ChalkBoard feature allows you to write and draw messages on a pro-

jected image. See page E-61

NOTE: This feature is available only when using with USB mouse. See page E-58.

Help

Contents

Provides an online help about how to use the menus. An underlined link

means that you can move to an adjustment item directly.

Selecting the underlined link and pressing ENTER moves to the corre-

sponding adjustment item.

Information

Displays the status of the current signal, and the lamp and the projector

usage hours. This dialog box has three pages.

The information included are as follows:

[Page 1]

[Page 2]

[Page 3]

Source Name

Input Terminal

Entry No.

Signal Type

Video Type

Sync Type

Remaining Lamp Time (%)

Lamp Hour Meter (H)

Projector Usage (H)

Horizontal Frequency Interlace

Vertical Frequency

Sync Polarity

E-119

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU Ͼ Menu Descriptions & Functions

NOTE: The progress indicator shows the percentage of remaining bulb life. The

value informs you of the amount of lamp and projector usage respectively.

Remaining Lamp Time Display:

When the remaining lamp time reaches 0, the Remaining Lamp Time

bar indicator changes from 0% to 100 Hours and starts counting down.

If the remaining lamp time reaches 0 hours, the projector will not turn

on regardless of whether the lamp mode is set to Normal or Eco.

Returning to Factory Default

The Factory Default feature allows you to change adjustments and setting

to the factory preset for source.

All Data ........... Reset all the adjustments and settings for all the sig-

nals to the factory preset except Remaining LampTime,

Lamp Hour Meter, Projector Usage, Language, Back-

ground, Entry List, Communication Speed, LAN Mode,

Security and Password.(To reset the lamp usage time,

see “Clear Lamp Hour Meter” on page E-100)

Current Signal . Resets the adjustments for the current signal to the

factory preset levels.

All the items in "Picture", "Volume", "Image Options"

and "Picture Management" can be reset.

E-120

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

This section describes the simple maintenance procedures you should

follow to replace the lamp, and to clean the cabinet and the lens.

Replacing the Lamp

After your lamp has been operating for 2000 hours (up to 3000 hours :Eco

mode) or longer, the "Lamp" indicator in the cabinet will blink red and the

message will appear. Even though the lamp may still be working, replace

it at 2000 hours (up to 3000 hours : Eco mode) to maintain optimal projec-

tor performance.

CAUTION

• DO NOT TOUCH THE LAMP immediately after it has been used. It

will be extremely hot. Turn the projector off, wait 90 seconds, turn off

the main power switch, and then disconnect the power cable. Allow

at least one hour for the lamp to cool before handling.

• DO NOT REMOVE ANY SCREWS except the lamp cover screw and

two lamp case screws.You could receive an electric shock.

• The projector will turn off and go into stand by mode after 2100 hours

(up to 3100 hours : Eco mode) of service. If this happens, be sure to

replace the lamp. If you continue to use the lamp after 2000 hours

(up to 3000 hours : Eco mode) of use, the lamp bulb may shatter, and

pieces of glass may be scattered in the lamp housing. Do not touch

them as the pieces of glass may cause injury.

If this happens, contact your NEC dealer for lamp replacement.

E-121

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

To replace the lamp:

1. Loosen the lamp cover screw until the screwdriver goes into a freewheel-

ing condition and remove the lamp cover. The lamp cover screw is not

removable.

2. Loosen the two screws securing the lamp housing until the screwdriver

goes into a freewheeling condition. The two screws are not removable.

3. Remove the lamp housing by pulling out the handle.

NOTE: There is an interlock on this case to prevent the risk of electrical shock.

Do not attempt to circumvent this interlock.

Interlock

E-122

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

4. Insert a new lamp housing until the lamp housing is plugged into the

socket.

CAUTION

Do not use a lamp other than the NEC replacement lamp (LT60LPK).

5. Secure it in place with the two screws.

Be sure to tighten the screws.

6. Reattach the lamp cover.

7. Tighten the lamp cover screw.

Be sure to tighten the screw.

E-123

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

8. After you install a new lamp, from the menu select [Projector Options] →

[Setup] → [Page 4] → [Clear Lamp Hour Meter] to reset the lamp usage

hours.

If the projector will not be turned on after using 2100 hours (up to 3100

hours : Eco mode) of service, press and hold the [Help] button on the

remote control for ten seconds or longer to reset the lamp time clock to

zero.

Cleaning

Cleaning the Cabinet and the Lens

E R

A T U

S T

M P

L A

I G

E C N

R D

P C - C A

S E L E C T

1. Turn off the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a

mild detergent. Never use strong detergents or solvents such as alcohol or

thinner.

3. Use a blower or lens paper to clean the lens, and be careful not to scratch

E C N

P C - C A R D

or mar the lens.

E-124

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

Lens Protector

The lens barrel has threads on the outside for mounting a commercially

available lens protector (φ 62mm for LT260K and φ 72mm for LT240K) to

protect the lens from dirt, dust, scratches and damage. Note that both a

lens protector and the supplied lens cap cannot be used at the same time.

CAUTION: Use only transparent lens protectors designed for lens protec-

tion. Use of filters for light reduction and special effects, such as ND (Neu-

tral Density) filters and color filters, can absorb heat, resulting in damage

to the filter and the projector.

E-125

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

This section helps you resolve problems you may encounter while setting up or

using the projector.

Power Indicator

Indicator Condition

Off

Projector Condition

Note

The main power is off

–

Blinking light

Steady light

Green blinking

0.5 sec ON,

0.5 sec OFF

2.5 sec ON,

0.5 sec OFF

0.5 sec ON,

0.5 sec OFF

The projector is getting ready Wait for a moment.

to turn on.

Green blinking

Orange blinking

The projector is in Sleep mode.

–

The projector is cooling down. Wait for a moment.

Green

The projector is turned on.

The projector is in Standby or

Idle.

–

Orange

Status Indicator

Indicator Condition

Off

Red blinking

Projector Condition

Note

Normal

–

Blinking light

1 cycle (0.5 sec ON, Lamp cover error

2.5 sec OFF)

Replace the lamp

cover correctly.

The projector is

overheated. Move

the projector to a

cooler location.

Power unit will not

work correctly.

Fans will not work

correctly.

2 cycle (0.5 sec ON, Temperature error

0.5 sec OFF)

3 cycle (0.5 sec ON, Power error

0.5 sec OFF)

4 cycle (0.5 sec ON, Fan error

0.5 sec OFF)

6 cycle (0.5 sec ON, Lamp error

0.5 sec OFF)

Lamp fails to light.

Wait a full minute and

then turn on again.

The projector is re-

firing.

Green blinking

Orange

Re-firing the lamp

Control key locked

Steady light

You have pressed

control panel key

when Control Key

Lock is enabled.

–

Green

Idle condition

E-126

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Lamp Indicator

Indicator Condition

Off

Projector Condition

Normal

Note

–

Blinking light

Steady light

Red

Lamp has reached its end of Replace the lamp.

life. Lamp replacement mes-

sage will be displayed.

Red

Lamp has been used beyond Replace the lamp.

its limit. The projector will not

turn on until the lamp is re-

placed.

Green

Lamp mode is set to Eco mode

–

E-127

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Common Problems & Solutions

Problem

Check These Items

Does not turn on

•

Check that the power cable is plugged in and that the power button on the projector

cabinet or the remote control is on. See pages E-35 and 36.

•

Ensure that the lamp cover is installed correctly. See page E-123.

Check to see if the projector has overheated or the lamp usage exceeds 2100 hours

(up to 3100 hours : Eco mode). If there is insufficient ventilation around the projec-

tor or if the room where you’re presenting is particularly warm, move the projector

to a cooler location.

No picture

•

Use the menu to select your source (RGB 1/2, Video, S-Video, Viewer or LAN). See

page E-39.

•

Ensure your cables are connected properly.

Use menus to adjust the brightness and contrast. See page E-85.

Remove the lens cap.

Reset the settings or adjustments to factory preset levels using the Factory Default

in the Adjustment Menu. See page E-120.

Image isn’t square to the

screen

•

Reposition the projector to improve its angle to the screen. See page E-41 or 42.

Use the 3DReform function to correct the trapezoid distortion. See page E-44.

Picture is blurred

•

Adjust the focus. See page E-43.

Reposition the projector to improve its angle to the screen. See page E-41 or 42.

Ensure that the distance between the projector and screen is within the adjustment

range of the lens. See page E-22-26.

•

Condensation may form on the lens if the projector is cold, brought into a warm

place and is then turned on. Should this happen, let the projector stand until there is

no condensation on the lens.

Image is scrolling verti-

cally, horizontally or

both

•

Use menus or Source button on the remote control or the cabinet to select the

source you want to input.

Remote control does

not work

•

Install new batteries. See page E-19.

Make sure there are no obstacles between you and the projector.

Stand within 22 feet (7 m) of the projector. See page E-20.

Make sure that you are in the Projector mode and the PJ button lights in red. If not,

press the PJ button. See page E-52.

Indicator is lit or blink-

ing

•

See the Status Indicator on pages E-126 and 127.

Cross color in RGB

mode

If Auto Adjust is off, turn it on or adjust the image manually with the Position/Clock

in the Image Options. See pages E-87, 88 and 98.

USB mouse does not

work

Make sure that your USB mouse is properly connected to the projector.

The projector may not support some brands of a USB mouse.

E-128

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

When using the Viewer function

Problem

Check These Items

No picture

• Is “Viewer” selected from the Source menu?

• Is the PC card seated in the PC Card slot completely?

• Are slide data stored in the PC card?

• Have the contents of the PC card been destroyed?

Contents of PC Card are • Use a computer, etc., to repair the data.

damaged

For more information contact your dealer.

E-129

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

This section provides technical information about the LT260K/LT240K Projector's

performance

Model Number

LT260K/LT240K

Optical

DMD™

Resolution

Lens

Single Chip Digital Micromirror Device(DMD™)

1024

768 pixels* up to UXGA with Advanced AccuBlend

Manual zoom and focus:

LT260K: F2.2 - 2.5 f=28.4mm - 34.0mm

LT240K: F2.5 - 2.8 f=22.4mm - 27.0mm

220 W DC standard

Lamp

Image Size

Projection Distance

30 inches - 500 inches (0.8 m - 12.7 m) diagonal

LT260K: 3.8ft - 80.7ft / 1.18m - 24.6m

LT240K: 2.95ft - 62.3ft / 0.90m - 19.0m

LT260K: 14.7°-15.2°(wide) / 12.2°-12.4°(tele)

LT240K: 18.6°-19.4°(wide) / 15.7°-16.2°(tele)

Projection Angle

Electrical

Inputs

2 RGB, 1 S-Video, 1 Video, 1 PC Card, 1 Stereo Mini

Audio, 1 (L/R) RCA Audio, 1 PC Control

1 RGB, 1 Stereo Mini Audio

Outputs

USB Port

1 A Type, 1 B Type

Video Compatibility

NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM,

HDTV:1080i, 720p, 480p, 480i (w/optional cable)

Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)

Vertical: 50 Hz to 120 Hz

Scan Rate

Video Bandwidth

Pixel Clock Freq

RGB: 100 MHz (-3dB)

Less than 135 MHz

Color Reproduction

Horizontal Resolution

16.7 million colors simultaneously, Full color

NTSC / NTSC4.43/PAL / YCbCr: 540 TV lines

SECAM: 300 TV lines

RGB: 1024 dots (H)

768 dots (V)

* Effective pixels are more than 99.99%.

E-130

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

External Control

RS232, IR, LAN (optional)

Sync Compatibility

Built-in Speakers

Power Requirement

Input Current

Separate Sync / Composite Sync / Sync on G

1 (monaural)

100 - 120V AC / 200 - 240V AC, 50 / 60 Hz

3.0A (100 - 120V AC) / 1.5A (200 - 240V AC)

280W (0.6W at Standby)

Power Consumption

Mechanical

Installation

Orientation: Desktop/Front, Desktop/Rear, Ceiling/Front,

Ceiling/Rear

Dimensions

Net Weight

10.2" (W)

3.6" (H)

10.8" (D)

260mm (W)

92mm (H)

275mm (D)

(not including protrusions)

LT260K: 6.5 lbs / 2.9 kg

LT240K: 7.1 lbs / 3.2 kg

Environmental Considerations

Operational Temperatures :

41° to 95°F (5° to 35°C), 20% to 80% humidity

(non-condensing)

Storage Temperatures :

14° to 122°F (-10° to 50°C), 20% to 80% humidity

(non-condensing)

Regulations

UL Approved (UL 1950, CSA 950)

Meets DOC Canada Class B requirements

Meets FCC Class B requirements

Meets AS/NZS3548 Class B

Meets EMC Directive (EN55022:1998, EN55024-1998,

EN61000-3-2, EN61000-3-3)

Meets Low Voltage Directive (EN60950, TUV GS Ap-

proved)

For additional information visit:

US : http://www.necvisualsystems.com

Europe : http://www.nec-europe.com/

Global : http://www.nec-pj.com/

Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks

of Texas Instruments.

The specifications are subject to change without notice.

E-131

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Cabinet Dimensions

92 (3.6")

260 (10.24")

57 (2.24")

* LT240K: 319mm (12.56”)

E-132

Unit = mm (inch)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Pin Assignments of D-Sub RGB Input Connector

Mini D-Sub 15 Pin Connector

Signal Level

Video signal : 0.7Vp-p (Analog)

Sync signal : TTL level

* RGB 1 Input only

15 14 13 12 11

Pin No.

RGB Signal (Analog)

YCbCr Signal

Red

Green or Sync on Green

Blue

Ground

Red Ground

Cr Ground

Y Ground

Cb Ground

Green Ground

Blue Ground

No Connection

Sync Signal Ground

Ground

Bi-directional DATA (SDA)*

Horizontal Sync or Composite Sync

Vertical Sync

Data Clock*

E-133

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Compatible Input Signal List

Signal

Resolution

( Dots )

Frequency H. Refresh Rate

Dot Clock

( MHz )

( kHz )

( Hz )

NTSC

PAL

–

15.734

15.625

31.47

34.97

–

SECAM

VESA

IBM

–

640

480

640

480

640

480

640

480

640

480

640

480

640

480

640

480

640

480

720

350

720

400

720

350

720

400

800

600

800

600

800

600

800

600

800

600

832

624

1024

768

1024

768

1024

768

1024

768

1024

768

1024

768

1152

864

1152

870

1152

900

1152

900

1280

960

1280

1024

59.94

25.175

31.334

30.24

31.5

31.49

MAC

VESA

IBM

66.67

72.81

37.86

37.5

39.375

43.269

31.469

37.927

39.44

35.16

37.879

48.077

46.88

53.674

49.725

35.5

VESA

IBM

85.01

70.09

85.04

87.85

56.25

60.32

72.19

28.322

35.5

VESA

IBM

VESA

MAC

VESA

MAC

VESA

MAC

SUN

49.5

56.25

57.283

44.9

85.06

74.55

43 Interlaced

48.363

56.476

60.241

60.023

68.677

67.5

70.07

74.93

75.03

78.75

94.5

108

68.681

61.796

71.736

75.06

65.95

76.05

100

92.94

105.6

108

SGI

VESA

63.981

60.02

108

E-134

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Signal

Resolution

( Dots )

Frequency H. Refresh Rate

Dot Clock

( MHz )

( kHz )

( Hz )

MAC

1280

1024

1280

1024

1280

1024

1280

1024

1280

1024

69.89

78.125

81.13

79.976

91.146

33.75

28.13

65.2

118.5

135

72.01

SUN

VESA

76.11

135

75.03

135

85.02

157.5

74.25

HDTV (1080i)(1125i)1920

1080

HDTV (1080i)(1125i)1920

1080

HDTV (720p)(750p)1280

720

60 Interlace

50 Interlace

60 Progressive 74.25

59.94 Progressive 27

SDTV (480p)(525p)

VESA

–

31.47

75.0

1600

1200

1600

1200

1600

1200

1600

1200

–

162

VESA

81.3

175.5

189

VESA

87.5

VESA

93.75

15.734

15.625

202.5

DVD YCbCr

59.94 Interlaced –

50 Interlaced

–

#:Images in above flagged with # are compressed with Advanced

AccuBlend on LT260K and LT240K.

NOTE: Some composite sync signals may not be displayed correctly.

Signals other than those specified in the table above may not be displayed cor-

rectly. If this should happen, change the refresh rate or resolution on your PC.

Refer to Display Properties help section of your PC for procedures.

UXGA (1600

1200) is supported for separate sync signal only.

E-135

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

PC Control Codes and Cable Connection

PC Control Codes

Function

Code Data

POWER ON

02H

00H

01H

03H

10H

11H

12H

13H

14H

15H

00H

02H

00H

02H

03H

01H

12H

13H

14H

15H

16H

17H

POWER OFF

02H

INPUT SELECT RGB 1

INPUT SELECT RGB 2

INPUT SELECT VIDEO

INPUT SELECT S-VIDEO

INPUT SELECT VIEWER

PICTURE MUTE ON

PICTURE MUTE OFF

SOUND MUTE ON

SOUND MUTE OFF

ON SCREEN MUTE ON

ON SCREEN MUTE OFF

02H

01H

02H

06H

0BH

1FH

09H

0AH

0EH

13H

27H

02H

NOTE: Contact your local dealer for a full list of PC Control Codes if needed.

Cable Connection

Communication Protocol

Baud rate : 38400 bps

Data length : 8 bits

Parity : No parity

Stop bit : One bit

X on/off : None

Communications procedure : Full duplex

NOTE: Depending on the equipment, a lower baud rate may be recommended for

long cable runs.

PC Control Connector (DIN-8P)

To RxD of PC

NOTE: Pins 2, 3, 5, 6 and 8 are used

inside the projector.

To GND of PC

To TxD of PC

E-136

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Using Software Keyboard

1 to 0 and Characters ......... Use to type in IP address or projector

name

SP ....................................... Inserts a space

BS ....................................... Deletes one character backward

̇ ......................................... Returns to the previous

̈ ......................................... Advances to the next

OK ....................................... Executes the selection

Cancel ................................. Cancels the selection

Drag bar .............................. Use to move the software keyboard on the

screen.

MODE ................................. Selects one of three modes for alphabet

and special characters.

HEX/ASCII .......................... Toggles between “HEX” and “ASCII”.

E-137

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Operation Using an HTTP Browser

Overview

The use of HTTP server functions will allow control of the projector from a

web browser without the installation of special software. Please be sure to

use “Microsoft Internet Explorer 4.x”or a higher version for the web browser.

(This device uses “JavaScript” and “Cookies” and the browser should be

set to accept these functions. The setting method will vary depending on

the version of browser. Please refer to the help files and the other informa-

tion provided in your software.)

NOTE:

* The use of HTTP server functions is not available during Standby mode.

* The display’s or button’s response can be slowed down or operation may not be

accepted depending the settings of your network. Should this happen, consult

your network administrator.

* The projector may not respond if its buttons are repeatedly pressed in rapid

intervals. Should this happen, wait a moment and repeat. If you still can’t get

any response, pull out and then re-insert the LAN card.

Access is gained to the HTTP server functions by specifying

http:// <the projector’s IP address> /index.html

in the entry column of the URL.

CAUTION:

Do not use the HTTP Server functions and the Dynamic Image Utility in-

cluded on the supplied CD-ROM. Using both at the same time may result

in a connection failure or slow response.

E-138

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Preparation Before Use

Make network connections and set up the projector and confirm that it is

complete before engaging in browser operations.(See “Setting LAN Mode”

on page E-102.)

Operation with a browser that uses a proxy server may not be possible

depending on the type of proxy server and the setting method. Although

the type of proxy server will be a factor, it is possible that items that have

actually been set will not be displayed depending on the effectiveness of

the cache, and the contents set from the browser may not be reflected in

operation. It is recommended that a proxy server not be used unless it is

unavoidable.

Handling of the Address for Operation via a Browser

Regarding the actual address that is entered for the address or entered to

the URL column when operation of the projector is via a browser, the host

name can be used as it is when the host name corresponding to the IP

address of the projector has been registered to the domain name server

by a network administrator, or the host name corresponding to the IP ad-

dress of the projector has been set in the “HOSTS” file of the computer

being used.

Example 1:

When the host name of the projector has been set to

“pj.nec.co.jp”,

http://pj.nec.co.jp/index.html

is specified for the address or the entry column of the URL.

When the IP address of the projector is “192.168.73.1”,

access is gained to the

Example 2:

HTTP server functions by specifying

http://192.168.73.1/index.html

for the address or the entry column of the URL.

E-139

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Structure of the HTTP Server

Power: This controls the power of the projector.

On ................... Power is switched on.

Off ................... Power is switched off.

Volume: This controls the volume of the projector.

̆ ..................... Increments the volume adjustment value.

̄ ..................... Decrements the volume adjustment value.

Mute: This controls the mute function of the projector.

All On .............. Mutes each of the video, audio, and on-screen display

functions.

All Off .............. Cancels the muting of each of the video, audio, and

on-screen display functions.

Picture On ....... Mutes the video.

Picture Off ....... Cancels the video muting.

Sound On ........ Mutes the audio.

Sound Off ........ Cancels the audio muting.

OSD On .......... Mutes the on-screen display.

OSD Off .......... Cancels the muting of the on-screen display.

E-140

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Picture: Controls the video adjustment of the projector.

Brightness ̆ ... Increments the brightness adjustment value.

Brightness ̄ ... Decrements the brightness adjustment value.

Contrast ̆ ...... Increments the contrast adjustment value.

Contrast ̄ ...... Decrements the contrast adjustment value.

Color ̆ ........... Increments the color adjustment value.

Color ̄ ........... Decrements the color adjustment value.

Hue ̆ ............. Increments the hue adjustment value.

Hue ̄ ............. Decrements the hue adjustment value.

Sharpness ̆ ... Increments the sharpness adjustment value.

Sharpness ̄ ... Decrements the sharpness adjustment value.

The functions that can be controlled will vary depending on the signal

being input to the projector.

Source Select: This switches the input connector of the projector.

RGB1 .............. Switches to the RGB 1 connector.

RGB2 .............. Switches to the RGB 2 connector.

Video ............... Switches to the Video connector.

S-Video ........... Switches to the S-Video connector.

Viewer ............. Switches to the Viewer.

LAN ................. Switches to a LAN signal.

Projector Status: This displays the condition of the projector.

Remaining Lamp Time ... Displays the remaining life of the lamp as a per-

centage.

Lamp Hour Meter ...... Displays how many hours the lamp has been

used.

Projector Usage ........ Displays how many hours the projector has been

used.

Error Status ............... Displays the status of errors occurring within the

projector.

Refresh ..................... Updates the display of the following conditions.

E-141

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

TravelCare Guide

TravelCare - a service for international travelers

This product is eligible for "TravelCare", NEC's unique international war-

ranty.

Please note that TravelCare coverage differs in part from coverage under

the warranty included with the product.

Services offered with TravelCare

This warranty allows customers to receive service on their product at the

NEC and NEC-designated service stations in the countries listed herein

when temporarily traveling internationally for business or pleasure.

For details on services offered by the different service stations, please

refer to the "List of TravelCare Outlets" below.

1 Repair services

The product will be repaired and delivered within 10 business days, not

including shipping time.

During the term of warranty, the cost of maintenance parts, labor costs

for repairs and shipping costs within the service station's coverage area

are covered by the warranty.

2 Replacement product rental service

If the customer desires, he or she can rent a replacement product while

the original product is being repaired.

Fee: US$200 for 12 days

This fee must be paid at the local service station in cash or credit card.

The $200 rental fee is non-refundable even if the customer rents it less

than 12 days before returning.

The replacement product will be delivered within 3 business days.

If the customer did not return the replacement product within 12 days,

the customer will be charged the price of the unit.

If the customer returned the replacement product in a faulty or dam-

aged condition, the repair cost will be charged to the customer.

E-142

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Note that this service is not offered in all countries and regions. Please

refer to the "List of TravelCare Outlets".

In addition, this replacement product rental service is not offered after

the product's warranty has expired.

Term of warranty

a. Upon presentation of the warranty or receipt received upon purchase:

Valid for the term indicated on the warranty or the normal term of war-

ranty for the country of purchase.

b. When only the product is brought in:

Valid for a period of within 14 months of the date of manufacture indi-

cated by the serial number attached to the product.

2 When a product whose term of warranty is expired is brought in:

Repairs will be offered for a fee. In this case the customer is not eligible

for the replacement product rental service.

3 In the following cases, repairs may be charged, even if the product's

warranty is still in effect:

1) If the term of warranty, model name, serial number and name of the

store of purchase are not indicated on the warranty or have been al-

tered.

2) Problems or damage caused by dropping or shocks during shipment or

movement by the customer or by improper handling by the customers.

3) Problems or damage caused by improper usage or unwarrantable al-

terations or repairs by the customer.

4) Problems or damage caused by fire, salt damage, gas damage, earth-

quakes, lightning damage, storm or flood damage or other natural di-

sasters or such external factors as dust, cigarette smoke, abnormal

voltage, etc.

5) Problems or damage caused by use in hot or humid places, in vehicles,

boats or ships, etc.

6) Problems or damage caused by expendable supplies or devices con-

nected to the product other than those designated by NEC.

E-143

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

7) Problems caused by natural consumption, wear or deterioration of parts

under normal usage conditions.

8) Problems or damage to lamps and other expendable supplies, included

parts or optional parts.

9) Other conditions stipulated in the warranty included with the product

also apply.

The product can be used overseas with voltages of 100 to 120V and 200 to 240V

by using a power cable suited for the standards and power source voltage of the

country in which the product is being used.

✍

List of TravelCare Outlets

This list applies as of June 1, 2002.

For the most up-to-date information, please refer to the websites of the

service stations in the various countries on the List of TravelCare Outlets

or to the NEC website at http://www.nec-pj.com.

List of TravelCare Outlets

In Europe

NEC Europe, Ltd. / European Technical Centre

Address:

Telephone:

Fax Line:

Unit G, Stafford Park 12, Telford TF3 3BJ, U.K.

+44 1952 237000

+44 1952 237006

Email Address: [email protected]

WEB Address: http://www.neceur.com

(Regions Covered)

EU: Austria*, Belgium*, Denmark*, Finland*, France*, Germany*,

Greece*, Ireland*, Italy*, Luxembourg*, The Netherlands*,

Portugal*, Spain*, Sweden* and the United Kingdom*

EEA: Norway*, Iceland and Liechtenstein

E-144

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

In North America

NEC Solutions (America), Inc.

Address:

1250 Arlington Heights Road, Itasca,

Illinois 60143, U.S.A.

+1 800 836 0655

+1 800 356 2415

Telephone:

Fax Line:

Email Address: [email protected]

WEB Address: http://www.necvisualsystems.com

(Regions Covered)

U.S.A. *, Canada*

In Oceania

NEC Australia Pty., Ltd.

Address:

New South Wales;

184 Milperra Road, Reversby 2212

Victoria;

480 Princess Hwy Noble Park 3174

South Australia;

84A Richmond Road, Keswick 5035

Queensland;

116 Ipswich Road, Woollongabba 4102

Western Australia;

45 Sarich Court Osborne Park 6017

131 632 (from domestic)

+61 8 8375 5706 (from overseas)

+61 8 8375 5757

Telephone:

Fax Line:

Email Address: [email protected]

WEB Address: http://www.nec.com.au

(Regions Covered)

Australia*, New Zealand

E-145

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

In Asia and Middle East

NEC Viewtechnology, Ltd.

Address:

686-1, Nishioi, Oi-Machi, Ashigarakami-Gun,

Kanagawa 258-0017, Japan

+81 465 85 2369

+81 465 85 2393

Telephone:

Fax Line:

Email Address: [email protected]

WEB Address: http://www.nec-pj.com

(Regions Covered)

Japan*

NEC Hong Kong Ltd.

Address:

11th Floor, Tower B, New Mandarin Plaza, 14 Science

Museum Road,

Tsim Sha Tsui East, Kowloon, Hong Kong

+852 2369 0335

+852 2795 6618

Telephone:

Fax Line:

Email Address: [email protected]

WEB Address: http://www.nec.com.hk

(Regions Covered)

Hong Kong

NEC Taiwan Ltd.

Address:

7F, No.167, SEC.2, Nan King East Road, Taipei,

Taiwan, R.O.C.

Telephone:

Fax Line:

+886 2 8500 1734

+886 2 8500 1420

Email Address: [email protected]

WEB Address: http://www.nec.com.tw

(Regions Covered)

Taiwan

E-146

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

NEC Singapore Pte. Ltd

Address:

401 Commonwealth Drive, #07-02, Haw ParTechnocentre,

Singapore 149598

+65 6 273 8333

+65 6 274 2226

Telephone:

Fax Line:

Email Address: [email protected]

WEB Address: http://www.nec.com.sg

(Regions Covered)

Singapore

Hyosung Data System, Ltd.

Address:

7th Floor, Cheongdam Building, 52, Cheongdam-Dong,

Kangnam-Ku, Seoul, Korea 135-100

+82 2 510 0234

+82 2 540 3590

Telephone:

Fax Line:

Email Address: [email protected]

(Regions Covered)

South Korea

Lenso Communication Co., Ltd.

Address:

292 Lenso House 4, 1st Floor, Srinakarin Road,

Huamark, Bangkapi, Bangkok 10240, Thailand

+66 2 375 2425

+66 2 375 2434

Telephone:

Fax Line:

Email Address: [email protected]

WEB Address: http://www.lenso.com

(Regions Covered)

Thailand

E-147

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

ABBA Electronics L.L.C.

Address:

Tariq Bin Ziyad Road, P.O.Box 327, Dubai,

United Arab Emirates

+971 4 371800

+971 4 364283

Telephone:

Fax Line:

Email Address: [email protected]

(Regions Covered)

United Arab Emirates

Samir Photographic Supplies

Address:

Telephone:

Fax Line:

P.O.Box 599, Jeddah 21421, Saudi Arabia

+966 2 6828219

+966 2 6830820

Email Address: [email protected]

(Regions Covered)

Saudi Arabia

In countries designated with an asterisk(*), replacement product rental service

are offered.

✍

E-148

Download from Www.Somanuals.com. All Manuals Search And Download.

P-1/

Date:

TO: NEC or NEC's Authorized Service Station:

FM:

(Company & Name with signature)

Dear Sir (s),

I would like to apply your TravelCare Service Program based on attached registration and qualification

sheet and agree with your following conditions, and also the Service fee will be charged to my credit card

account, if I don't return the Loan units within the specified period. I also confirm following information is

correct. Regards.

Application Sheet for TravelCare Service Program

Country,

product purchased :

User's Company Name :

User's Company Address :

Phone No., Fax No. :

User's Name :

User's Address :

Phone No., Fax No. :

Local Contact office :

Local Contact office Address :

Phone No., Fax No. :

User's Model Name :

Date of Purchase :

Serial No. on cabinet :

Problem of units per User :

Required Service :

(1) Repair and Return

(1) Credit Card

(2) Loan unit

Requested period of Loan unit :

Payment method :

(2) Travelers Cheque

(3) Cash

In Case of Credit Card :

Card No. w/Valid Date :

E-149

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Condition of your TravelCare Service Program

Enduser is requested to understand following condition of TravelCare Ser-

vice Program and fill necessary information into the application sheet.

1. Service Options:

There are 3 types of "Service" available. Enduser has to understand fol-

lowing condition and is required to fill in the Application Sheet.

1) Repair and Return:

The 'Faulty unit' is sent or collected from the customer. It is repaired

and returned within 10 days to the customer, excluding transport time.

There may have a case, repair and return can't be done by NEC Autho-

rized Service Station, because of shortage of spare parts due to same

model is not sold in the territory.

2) Repair and Return with Loan: (This service is limited to some Service

Stations)

This service is offered to the Enduser, who cannot wait until their unit is

repaired.

The customer can borrow a unit for $200 up to 12 days. Customer then

sends in inoperable unit to nearest NEC Authorized Service Station for

service. In order to prevent collection problem, Enduser is required to

fill in Application Sheet.

Enduser needs to confirm the availability of the Service to NEC Autho-

rized Service Stations.

3) Loan Only:

For this service, NEC Authorized Service Station supplies the customer

with a loan unit for US$200 up to 12 days. Customer keeps the inoper-

able unit and when customer returns home, customer arranges to have

the projector serviced in the home country.

E-150

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

2. Warranty Exclusions:

This program does not apply if the Projector's serial number has been

defaced, modified or removed.

If, in the judgement of NEC Authorized Service Station or its agent the

defects or failures result from any cause other than fair wear and tear or

NEC neglect, or fault including the following without limitation:

1) Accidents, transportation, neglect, misuse, abuse, water, dust, smoke

or default of or by the Customer its employees or agents or any third

party;

2) Failure or fluctuation of electrical power, electrical circuitry, air condi-

tioning, humidity control or other environmental conditions such as use

it in smoking area;

3) Any fault in the attachments or associated products or components

(whether or not supplied by NEC or its agents which do not form part of

the Product covered by this warranty);

4) Any act of God, fire, flood, war, act of violence or any similar occur-

rence;

5) Any attempt by any person other than any person authorized by NEC

to adjust, modify, repair, install or service the product.

6) Any Cross-border charges such as, duty, insurance, tax etc.

3. Charges for Warranty Exclusions and Out of Warranty Case:

In case faulty unit is under warranty exclusions case or under Out of War-

ranty period, NEC Authorized Service Station will Inform estimation of actual

service cost to the Enduser with reason.

4. Dead on Arrival (DOA):

Enduser must take this issue up with their original supplier in the country

of purchase.

NEC Authorized Service Station will repair the DOA unit as a Warranty

repair, but will not exchange DOA unit with new units.

E-151

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

5. Loan Service Charges and Conditions:

Upon acceptance of this NEC Projector, Customer agrees to assume li-

ability for this loan unit.

The current cost of use of this loan unit is $200.00 USD for 12 calendar

days.

If Customer does not return the unit within the 12 calendar days, Cus-

tomer will be charged the next highest cost up to and including the full list

price to Credit Cards, which price will be informed by NEC Authorized

Service Stations.Please see the attached listing of contacts for each country

to arrange for pickup of the loan unit.

If you return to their country of origin with the loan unit, you will be charged

additional freight to return the unit to the loaning country.

Thank you for your understanding of this program.

E-152

Download from Www.Somanuals.com. All Manuals Search And Download.

Nikon Camera Accessories MB D15 User Manual
Nikon Camera Flash SB 400 User Manual
NuTone Lawn Mower PM44 User Manual
Olympus Camera Accessories PPO E04 User Manual
Omnimount TV Mount 100 W C User Manual
Oricom Cordless Telephone SLIM 9000 User Manual
Panasonic Switch AW HB505 User Manual
Panasonic TV Video Accessories AW LK50 User Manual
Panasonic Ventilation Hood FV 08VQCL6 User Manual
Parker Products Video Game Keyboard OPS1200 User Manual