OPERATION AND PARTS MANUAL
SERIES
MODEL MVC80VH/VHW
ONE-WAY PLATE COMPACTOR
(HONDA GX160U1SM12 GASOLINE ENGINE)
Revision #3 (01/13/11)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Honda GX160U1SM12 Engine
Cylinder Head Assembly....................................38-39
Cylinder Barrel (Recoil) Assembly .....................40-41
Crankcase Cover Assembly...............................42-43
Crankshaft Assembly .........................................44-45
Piston/Rings Assembly.......................................46-47
Camshaft Assembly ...........................................48-49
Recoil Starter .....................................................50-51
Fan Cover Assembly ..........................................52-53
Carburetor Assembly .........................................54-55
Air Cleaner Assembly.........................................56-57
Muffler Assembly ...............................................58-59
Fuel Tank Assembly ...........................................60-61
Cooling Fan & Flywheel Assembly.....................62-63
Ignition Coil Assembly ........................................64-65
Control Assembly ...............................................66-67
MVC80VH/VHW
Plate Compactor
Proposition 65 Warning ............................................. 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Information................................................ 6-10
Specifications .......................................................... 11
Dimensions ............................................................. 12
General Information ................................................ 13
Components............................................................ 14
Basic Engine ........................................................... 15
Inspection........................................................... 16-17
Startup ............................................................... 18-19
Operation ................................................................ 19
Maintenance ...................................................... 20-22
Preparation For Long Term Storage ....................... 23
Troubleshooting ................................................. 24-25
Explanation Of Codes In Remarks Column ............ 26
Suggested Spare Parts ........................................... 27
Terms and Conditions Of Sale — Parts .................. 68
Component Drawings
Nameplate and Decals....................................... 28-29
Main Body Assembly.......................................... 30-31
Vibrator Assembly .............................................. 32-33
Water Tank Assembly (Option)........................... 34-35
Transport Wheel Assembly (lOption) .................. 36-37
NOTICE
Specification and part number are subject to
change without notice.
PAGE 4 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURE
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only)
Order parts on-line using Multiquip’s SmartEquip website!
:
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
Order via Phone:
1-800-427-1244
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
❒
❒
❒
❒
❒
Dealer Name and Address
✓ UPS/Fed Ex
✓ DHL
✓ Truck
■
■
Priority One
Ground
Shipping Address (if different than billing address)
Return Fax Number
■ Next Day
Second/Third Day
Applicable Model Number
■
Quantity, Part Number and Description of Each Part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
Lethal Exhaust Gases
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER,WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
l
PAGE 6 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
GENERAL SAFETY
CAUTION
NOTICE
„ This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
„ NEVER operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
„ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
„ Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
„ NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
„ NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
„ ALWAYS know the location of the nearest
fire extinguisher.
„ NEVER operate this equipment under the influence of
drugs or alcohol.
„ ALWAYS know the location of the nearest
first aid kit.
„ ALWAYS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance,doctor and fire department.
This information will be invaluable in the case of an
emergency.
„ ALWAYS check the equipment for loosened threads or
bolts before starting.
„ DO NOT use the equipment for any purpose other than
its intended purposes or applications.
„ ALWAYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
COMPACTOR SAFETY
DANGER
WARNING
„ DO NOT place hands or fingers inside engine
compartment when engine is running.
„ NEVER operate the equipment in an explosive
atmosphere or near combustible materials.An
explosion or fire could result causing severe
bodily harm or even death.
„ NEVER operate the engine with heat shields or
guards removed.
„ Keep fingers, hands hair and clothing away
from all moving parts to prevent injury.
WARNING
„ NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death.Disconnection of any of these
devices will void all warranties.
„ DO NOT remove the radiator cap while the
engine is hot. High pressure boiling water will gush out
of the radiator and severely scald any persons in the
general area of the compactor.
„ DO NOT remove the coolant drain plug
while the engine is hot. Hot coolant will
gush out of the coolant tank and severely
scald any persons in the general area of
the compactor.
CAUTION
„ NEVER lubricate components or attempt service on a
running machine.
NOTICE
„ DO NOT remove the engine oil drain plug while the
engine is hot. Hot oil will gush out of the oil tank and
severely scald any persons in the general area of the
compactor.
„ ALWAYS keep the machine in proper running condition.
„ Fix damage to machine and replace any broken parts
immediately.
CAUTION
„ ALWAYS store equipment properly when it is not being
used.Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
„ NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing equipment.
ENGINE SAFETY
DANGER
NOTICE
„ NEVER run engine without an air filter or with a dirty air
filter.Severe engine damage may occur.Service air filter
frequently to prevent engine malfunction.
„ The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
l
cause death if inhaled.
„ NEVER tamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
„ The engine of this equipment requires an adequate
free flow of cooling air. NEVER operate this equipment
in any enclosed or narrow
area where free flow of the
air is restricted. If the air
flow is restricted it will cause
injury to people and property
and serious damage to the
equipment or engine.
„ NEVER tip the engine to extreme angles during lifting as
it may cause oil to gravitate into the cylinder head, making
the engine start difficult.
PAGE 8 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
FUEL SAFETY
DANGER
BATTERY SAFETY (ELECTRIC START ONLY)
DANGER
„ DO NOT add fuel to equipment if it is placed inside truck
bed with plastic liner. Possibility exists of explosion or
fire due to static electricity.
„ DO NOT drop the battery.There is a possibility that the
battery will explode.
„ DO NOT expose the battery to open flames,
sparks, cigarettes, etc.The battery contains
combustible gases and liquids. If these
gases and liquids come into contact with a
flame or spark, an explosion could occur.
FUEL
WARNING
„ ALWAYS wear safety glasses when
handling the battery to avoid eye irritation.
The battery contains acids that can cause
injury to the eyes and skin.
FUEL
„ Use well-insulated gloves when picking up
the battery.
„ ALWAYS keep the battery charged. If the battery is not
charged, combustible gas will build up.
„ DO NOT start the engine near spilled fuel or combustible
fluids. Diesel fuel is extremely flammable and its vapors
can cause an explosion if ignited.
„ DO NOT charge battery if frozen. Battery can explode.
When frozen, warm the battery to at least 61°F (16°C).
„ ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
„ ALWAYS recharge the battery in a well-ventilated
environment to avoid the risk of a dangerous concentration
of combustible gases.
„ ALWAYS use extreme caution when working with
flammable liquids.
„ If the battery liquid (dilute sulfuric acid)
comes into contact with clothing or skin,
rinse skin or clothing immediately with
plenty of water.
„ DO NOT fill the fuel tank while the engine is running
or hot.
„ DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
„ If the battery liquid (dilute sulfuric acid) comes into
contact with eyes, rinse eyes immediately with plenty
of water and contact the nearest doctor or hospital to
seek medical attention.
„ Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
CAUTION
„ NEVER use fuel as a cleaning agent.
„ ALWAYS disconnect the NEGATIVE battery terminal
before performing service on the equipment.
„ DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
„ ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
TRANSPORTING SAFETY
CAUTION
„ NEVER allow any person or animal to stand underneath
the equipment while lifting.
NOTICE
„ Before lifting, make sure that the equipment parts (hook
and vibration insulator) are not damaged and screws are
not loose or missing.
„ Always make sure crane or lifitng device has been
properly secured to the lifting bail (hook) of the
equipment.
„ ALWAYS shutdown engine before transporting.
„ NEVER lift the equipment while the engine is running.
„ Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
„ Use adequate lifting cable (wire or rope) of sufficient
strength.
„ Use one point suspension hook and lift straight
upwards.
„ DO NOT lift machine to unnecessary heights.
„ ALWAYS tie down equipment during transport by
securing the equipment with rope.
ENVIRONMENTAL SAFETY
NOTICE
„ Dispose of hazardous waste properly.
Examples of potentially hazardous waste
l
are used motor oil, fuel and fuel filters.
„ DO NOT use food or plastic containers to dispose of
hazardous waste.
„ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
PAGE 10 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
TABLE 1. Specifications (Compactor)
MVC-80VH/MVC-80VHW
Models
Centrifugal Force
Number of Vibrations
Traveling Speed
2,928 lbs. (1,327 kg)
5,600 vibrations/min (93Hz)
72 ft./min (22 meters/min)
22.4 x 17.7 in.
570 x 450 mm
Plate Size (LxW)
36.6 x 17.7 x 39.4 in.
(930 x 450 x 1000 mm)
Overall Dimensions (L x W x H)
Operating Weight (VH)
Operating Weight (VHW)
161 lbs. (80.5 kg.)
183 lbs. ( 88.5 kg.)
Water Tank Capacity
(VHW Model Only)
13.8 qt. (13.0 liters)
Max. Area Of Compaction
6,827 sq. ft./hr. (660 sq. m/hr)
Table 2. Specifications (Engine)
Model
HONDA GX160U1SM12
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
Type
2.7 in. x 1.8 in.
(68 mm x 45 mm)
Bore X Stroke
Displacement
Max Output
163 cc (9.9 cu-in)
5.5 H.P./3600 R.P.M.
Engine
Approx. 0.95 U.S. gallons
(3.6 liters)
Fuel Tank Capacity
Unleaded Automobile
Gasoline
Fuel
Lube Oil Capacity
Speed Control Method
Starting Method
.60 liters (0.63 qts)
Centrifugal Fly-weight
Type
Recoil Start
Dimension
(L x W x H)
120 x 14.2 x 13.2 in.
(304 x 362 x 335 mm)
Dry Net Weight
23.1 lbs (10.48 Kg.)
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
E
A
F
D
C
B
TABLE 3. DIMENSIONS
DESCRIPTION
REFERENCE LETTER
DIMENSION in. (mm)
36 inches (1000 mm)
17 inches (450 mm)
24 inches (620 mm)
22 inches (570 mm)
37 inches (930 mm)
23 inches (590 mm)
Height (Handle Upright)
A
B
C
D
E
F
Width
Length (Handle Upright)
Plate Length
Length (Handle Lowered)
Height (Compactor Only)
35 x 19 x 26 inches
(860 x 480 x 670 mm)
Shipping Dimensions
PAGE 12 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
Definition of Plate Compactor
Frequency/Speed
The Mikasa MVC80VH/VHW is a walk behind, plate compactor
designed for the compaction of sand, mixed soils and asphalt.
This plate compactor is a powerful compacting tool capable of
applying a tremendous force in consecutive high frequency
vibrations to a soil surface. Its applications include compacting
for road, embankments and reservoirs as well as backfilling for
gas pipelines, water pipelines and cable installation work.
The compactor's vibrating plate has a frequency range between
5600 vpm (vibrations per minute). The travel speed of the
compactor is approximately 72 ft./minute (22 meters/minute).
Engine
The Mikasa MVC80VH/VHW Plate Compactor is equipped with
a Honda GX160U1SM12 gasoline engine.
Vibratory Plates
Controls
The vibratory plates of the MVC80VH/VHW produce low
amplitude high frequency vibrations, designed to compact
granular soils and asphalt.
Before starting the MVC80VH/VHW Plate Compactor identify
and understand the function of the controls and components.
The resulting vibrations cause forward motion.The engine and
handle are vibration isolated from the vibrating plate.
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
1
10
4
9
3
2
5
WATER TANK
(MVC-80VHW ONLY)
8
7
6
Figure 1. Plate Compactor Controls
Figure 1 shows the location of the basic controls and components
of the MVC80VH/VHW Plate Compactor.The function of each
control is described below:
6. Belt Cover – Remove this cover to gain access to the
V-belts.NEVER run the compactor without theV-belt cover.
If theV-belt cover is not installed, the possibility exists that
your hand may get caught between the V-belt and clutch,
causing serious injury and bodily harm.
1. Water Tank Cap (VHW Only) – Remove this cap to add
l
water to the water tank.
7. Vibrating Plate – A flat, open plate made of durable cast
2. FuelTank Cap – Remove this cap to add fuel.
iron construction used in the compacting of soil.
3.
Lifting Bale – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
8. Vibration Case – Encloses the eccentric, gears and
counter weights.
9. Water Shut-Off Valve (VHW only) – Turn this valve
downward to let water flow from the water tank to the water
tube.
4. Handle Bar – When operating the compactor use this
handle bar to maneuver the compactor.
5. Gasoline Engine – This plate compactor uses a HONDA
GX160U1SM12 engine. Refer to the HONDA owner's
manual for engine information and related topics.
10. Water Tank (VHW only) – Holds 13.8 quarts of water
(removable, no tools required).
PAGE 14 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC ENGINE
Figure 2. Engine Controls & Components
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
ENGINE COMPONENTS
the flow of fuel.
The engine (Figure 2) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
NOTICE
WARNING
Operating the engine without an air filter, with a damaged air
filter, or a filter in need of replacement will allow dirt to enter
the engine, causing rapid engine wear.
Add fuel to the tank only when the engine is
stopped and has cooled down. In the event
of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been
completely wiped up and the area
surrounding the engine is dry.
WARNING
Burn Hazard
Engine components can generate extreme
heat.To prevent burns, DO NOT touch these
areas while the engine is running or
immediatelyafteroperating. NEVER operate
the engine with the muffler removed.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward - SLOW, lever back toward operator -
FAST).
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
9. Muffler – Used to reduce noise and emissions.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
Before Starting
NOTICE
1.
Read safety instructions at the
The Oil Alert System will automatically stop the engine
before the engine falls below safe limits. Always be sure to
check the engine oil level prior to starting the engine.
beginning of manual.
2.
Clean the compactor, removing
dirt and dust, particularly the
engine cooling air inlet, carburetor
and air cleaner.
3.
4.
5.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
Table 4. Oil Type
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
Check carburetor for external dirt and dust. Clean with dry
compressed air.
Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
0°C or Lower
Engine Oil Check
DANGER
1.
To check the engine oil level, place the pump on secure
EXPLOSIVE FUEL!
level ground with the engine stopped.
Motor fuels are highly flammable and can
be dangerous if mishandled. DO NOT
smoke while refueling. DO NOT attempt to
refuel if the engine is hot or running.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 3) and wipe clean.
Fuel Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
Figure 3. Engine Oil Dipstick (Removal)
Insertandremovethedipsticklwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
3. When refueling, be sure to use a strainer for filtration. DO
3.
NOT top-off fuel. Wipe up any spilled fuel immediately!
4. If the oil level is low (Figure 4), fill to the edge of the oil filler
holewiththerecommendedoiltype(Table4).Maximum oil
capacity is 0.63 quarts (0.60 liters)
Figure 4. Engine Oil Dipstick (Oil Level)
PAGE 16 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
2. TheV-belt tension is proper if theV-belt bends 10 to 15 mm
(Figure 7) when depressed with finger at midway between
the clutch and vibration pulley shafts.
CAUTION
NEVER attempt to check theV-belt with the engine run-
ning.Severeinjurycanoccurofyourhand(Figure5)gets
caught between the V-belt and the clutch. Always use
safetygloves.
CLUTCH
PULLEY
Figure 7.V-BeltTension
3. A looseV-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
VIBRATOR
PULLEY
4. If theV-belt becomes worn or loose, replace it.
Figure 5.V-Belt Hazard
1. To check the V-belt tension, remove the three bolts that
secure the belt cover to the frame as shown in Figure 6.
Vibrator Oil Check
1. PlacetheMVC80VH/VHWplatecompactorhorizontallyon
aflatsurface.Makesurethecompactorislevelwhencheck-
ing the oil in the vibrator assembly.
2. Check vibratoroillevelbyremoving theplug (vibrator oilgauge)
asshowninFigure8. Theoillevelshouldbeuptotheoilplug.
Thevibratorholds 140cc(approximately4oz.).IMPORTANT,
if oil is required, replace using only SAE10W-30 motor oil.
Figure 8.Vibrator Oil Plug
Figure 6.V-Belt Cover Removal
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTUP
CAUTION
DO NOT attempt to run the compactor
NOTICE
The CLOSED position of the choke lever enriches the
fuel mixture for starting a COLD engine. The OPEN
position provides the correct fuel mixture for normal
operation after starting, and for restarting a warm engine.
D
until the Safety and Initial Start-up
sections have been read and understood.
1. Place the fuel valve lever (Figure 9) in the "ON" position.
4. Place the throttle lever (Figure 12) halfway between fast
andslow.
Figure 9. Fuel Valve Lever
2. Place the Engine ON/OFF switch (Figure 10) in the "ON"
position.
Figure 12. Throttle Lever
5. Grasp the starter grip (Figure 13) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingthecompressionpoint.Rewindtheropealittlefrom
that point and pull out sharply.
Starter Rope
CAUTION
Figure 10. Engine ON/Off Switch
DO NOT pull the starter rope all the way to the end
DO NOT release the starter rope after pulling.Allow it
to rewind as soon as possible.
3. PlacetheChokeLever(Figure11)inthe"OPEN"position.
l
nn
Figure 11. Choke Lever
Figure 13. Starter Grip
PAGE 18 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTUP/OPERATION
6. If the engine has started, slowly return the choke lever
(Figure 11) to the CLOSED position. If the engine has not
started, repeatsteps1through5.
Stopping the Engine
NOTICE
Stopping Engine
NEVER stop the engine suddenly while working at
high speeds.
7. Beforethecompactorisputintooperation,runtheenginefor
3-5minutes.
8. Check for abnormal engine noises or fuel leaks.
Normal Shutdown
Operation
1. Place the throttle lever (Figure 12) in slow position, and
listen for the engine speed to decrease.
CAUTION
2. PlacetheEngineON/OFFswitch(Figure10)inthe"OFF"
Makesuretofollowallsafetyrulesreferencedinthesafety
sectionofthismanualbeforeoperatingcompactor. Keep
work area clear of debris and other objects that could
cause damage to the compactor or bodily injury.
position.
3. Place the fuel valve lever (Figure 9) in the "OFF" position.
Emergency Shutdown
1. Oncetheenginehasstarted, movetheenginethrottlelever
1. Move the throttle lever quickly to the slow position, and
quickly to the fastposition.
place the Engine ON/OFF switch in the "OFF " position.
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the cen-
trifugalclutch.
NOTICE
ALWAYS move the throttle lever quickly without
hesitation, because increasing the engine speed slowly
causes the clutch to slip.
5. Firmlygraspthecompactor'shandlebar withbothhands, the
compactor will begin moving forward.
6. Slowlywalkbehindthecompactorandbeonthelookout for
anylargeobjectsorforeignmatterthatmightcausedamage
to the compactor or bodily injury.
7. Compactortravelingspeedmaydroponsoilswhichcontain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil.To
rectify this problem do the following:
■
Check the bottom plate to see if clay or equivalent material
has been lodged in the plate mechanism. If so, wash with
water and remove.
■
■
Remember the compactor does not work as efficiently on
clay or soils that have a high moisture content level.
If the soil has a high moisture level, dry soil to appropriate
moisture content level or carry out compaction twice.
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CAUTION
CAUTION
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number hours plate compactor is in use, and particular
working conditions.
Inspection and other services should always be carried
out on hard and level ground with the engine shutdown.
Inspection and Maintenance ServiceTables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 5 through 7.
CAUTION
Fuel piping and connections should be replaced every 2
years.
Table 5. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CHECK
lCLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
PAGE 20 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
3. Replace engine oil with recommended type oil as listed
in Table 4. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
TABLE 6. MACHINE INSPECTION
Item
Hours of Operation
4. Reinstall drain bolt with sealing washer and tighten se-
curely.
(Starting check)
Every 8 hours (every day)
Every 8 hours (every day)
Every 8 hours (every day)
Loose or lost screws
Damage of any part
Function of controlling
system part
Every 8 hours (every day)
Every 100 hours
Vibrator oil check
Vibrator oil
replacement
Every
300 hours
V-belt (clutch) check
Every 200 hour
Figure 14. Engine Oil (Draining)
Air Filter
Daily Service
■
■
■
Check for leakage of fuel or oil.
1. The air filter element should be cleaned because a clogged
air cleaner can cause poor engine starting, lack of power
and shorten engine life substantially.
Check engine oil.
Check for loose screws including tightness. See Table 6
below (tightening torque ), for retightening.
2. To clean or replace air filter loosen the wing nut on the air
filter housing (Figure 15), remove the cover and take out air
filter cartridge. If only cleaning of the air filter is desired blow
through the air filter cartridge from the inside, moving a jet of
dry compressed air up and down until all dust is removed.
TABLE 7.
TIGHTENING TORQUE (in. kg/cm) Diameter
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
4T
6-8T
11T
*
70
150
250
400
300
500
800
500
800
750
1,100 1,400 2,000
100
150
1,300 2,000 2,700 3,800
1,200 2,000 2,900 4,200 5,600
100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)
* (In case counter-part is of aluminum)
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt,
and screw.
ENGINEOIL
1. Replace the engine oil in first 20 hours of operation and
every 100 hours afterwards.
2. Drain the engine oil when the oil is warm after operation.
Removetheoilfillercapthenunscrewtheengineoildrain
pluglocatedatthebaseoftheengine. Draintheoldoilinto
a pan (Figure 14).
Figure 15. Air Cleaner
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Replacing the V-belt
Spark Plug
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway ofV-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that theV-belt will come off.
1. Remove and clean the spark plug (Figure 16).
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This
unit has electronic ignition, which requires no adjustments.
Reinstalling the V-belt
EngageV-belt to lower vibrator pulley and push theV-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
Checking Clutch
Check the clutch simultaneously withV-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked with
running check. If the shoe is worn, power transmission becomes
deficient and slipping will result.
Figure 16. Spark Plug Gap
Changing Vibrator Oil
1. When changing the vibrator oil, remove the drain plug
(Figure 8), and simply tip the compactor to drain the oil.
Note that the oil will drain more easily while it is hot.
Remember to use only 10W-30 motor oil when replacing
vibrator oil.
WARNING
NEVER attempt to check theV-belt with the engine run-
ning.Severeinjurycanoccurifyourhand(Figure 5)gets
caught between the V-belt and the clutch. Always use
safetygloves.
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover to
check theV-belt tension.Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
WARNING
Whenever the compactor's vibration becomes weak or lost
duringnormaloperationregardlessofoperationhours,check
theV-beltandclutchimmediately.
l
PAGE 22 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION FOR LONG-TERM STORAGE
Plate Compactor Storage
For storage of the plate compactor for over 30 days, the
following is required:
■
■
■
Drain the fuel tank completely or add STA-BIL to the fuel.
Run the engine until the fuel is completely consumed.
Completely drain the oil from the engine crankcase and
follow procedures described in the HONDA engine Owner's
Manual for engine storage.
■
■
■
Completely drain the compactor's hydraulic oil from the
vibrating case.
Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TABLE 8. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or
replace spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace
switch.
Replace ignition coil.
Set correct spark gap and
clean points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirtry?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Difficult to start, "fuel is available, spark
is present and compression is normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
l
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Apply lubricant to loosen fuel
cock lever, replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
PAGE 24 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE CAUSE
Air cleaner not clean?
SOLUTION
Clean or replace air cleaner
Check float adjustment, re-build
carbureator.
Improper level in carburetor?
"Weak in power" compression is
proper and does not misfire.
Defective Spark plug?
Defective Spark plug?
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Water in fuel system?
"Weak in power" compression is
proper but misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Replace with correct type of
spark plug.
Spark plug heat value improper?
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Recoil starter malfunction.
Check entire fuel system for
leaks or clogs.
Fuel flow restricted?
Recoil mechanism clogged with dust and Clean recoil assembly with soap
dirt?
and water.
Sprial spring loose?
Replace sprial spring.
TABLE 9. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Engine speed too low?
Clutch slips?
Set engine speed to correct RPM.
Check or replace clutch.
V-belt slips?
Adjust or replace V-belt.
Travel speed too low, and vibration is
weak.
Excessive oil in vibrator?
Drain excess oil and fill to proper level.
Check eccentric, gears and counter
weights.
Malfunction in vibrator housing?
Bearing Failure?
Replace Bearing
Insufficient engine output?
Check engine, compression etc.
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODES IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
WASHER, 3/8 IN....1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
NO. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
l
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
PAGE 26 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
MVC80VH/VHW COMPACTOR
WITH HONDA GX160U1SM12 ENGINE
1 to 5 Units
Qty.
P/N
Description
3 ......... 070100312 .............V-BELT
4 ......... 939010254 .............SHOCK ABSORBER
3 ......... 9807956846 ...........SPARK PLUG
1 ......... 28462ZH8003 ........ROPE, RECOIL STARTER
3 ......... 17210ZE1517 ........ELEMENT, AIR CLEANER
1 ......... 17620Z4H000 ........CAP, FUEL TANK
1 ......... 17672ZE2W01 .......FUEL FILTER, FUEL TANK
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
2
WATER TANK
(MVC-80VHW ONLY)
4
1
3
5
6
l
PAGE 28 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
NO
1
PART NO
PART NAME
QTY.
REMARKS
NAMEPLATE, SERIAL NO. ...................1........ CONTACT MQ PARTS DEPT.
DECAL, READ OWNERS MANUAL.......1........ NPA-329
DECAL, BELT GUARD WARNING .........1........ NPA-989
DECAL, MIKASA (120 X 60)) ................1........ WATERTANK
DECAL, MQ LOGO (71 X 55) ................2........ MQ/WATERTANK
DECAL, MIKASA LOGO (125 MM) ........1........ WATERTANK
DECAL, MOTOR OIL..............................1........ NPA-195
DECAL, MIKASA LOGO (TRIANGLE) ...1........ NPA-141
2
920203290
920203989
920101410
920201580
920105070
920201950
920101410
3
4
5
6
8
9
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN BODY ASSY.
MAIN BODY ASSY.
29
11
52
27
53
55
53
54
54
14-1
14-2
14-3
19
55
31
32
33
20
23
22-2
25
18
41
21
56
22-1
26-3
26-2
26-1
51
16
28-3
28-2
2
28-1
17
4
47-2
l
49
45
46
50
5
47-1
6
l
12
13
3
7
6
5
1
PAGE 30 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN BODY ASSY.
MAIN BODY ASSY.
NO
1
2
3
4
5
6
7
11
12
13
14-1
14-2
14-3
16
17
18
19
20
PART NO
PART NAME
VIBRATING PLATE 570X450
BASE
SHOCK ABSORBER D45-H41
EARTH WIRE
NUT M10
WASHER, LOCK M10
WASHER, FLAT M10
ENGINE ASSY. GX160U1SM12
BOLT, ENGINE
ENGINE NUT, REAR
BOLT 8X40 T
WASHER, LOCK M8
WASHER, FLAT M8
WASHER, FLAT M8
NYLON NUT M8
CLUTCH SPACER 20.2X25X9.4
CLUTCH ASSY.S-20-A1-124
KEY 5 X 5 X 35
QTY.
1
1
4
1
8
8
8
1
1
1
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
REMARKS
418118530
418216501
939010254
959404350
020310080
030210250
031110160
912216004
418457750
413436870
001220840
030208200
031108160
031108160
022710809
408421270
413332920
0053005201
952400130
001220820
030208200
070100312
418216470
001221035
030210250
031110160
418216480
001221053
030210250
031110160
418343420
020308060
030208200
031108160
418910070
404433430
952403450
001221020
030210250
413436720
001520845
020308060
418217060
416459340
009120407
416459320
418217050
21
WASHER 9304
BOLT 8 X 20 T
WASHER, LOCK M8
V-BELT RPF-3310
BELT COVER
22-1
22-2
23
25
26-1
26-2
26-3
27
28-1
28-2
28-3
29
31
32
33
41
45
46
47-1
47-2
49
50
51
BOLT 10X35 T
WASHER, LOCK M10
WASHER, FLAT M10
BELT COVER (INSIDE)
BOLT 10 X 65 T
WASHER, LOCK M10
WASHER, FLAT M10
COVER SEAL
NUT M8
WASHER, LOCK M8
WASHER, FLAT M8
VIB. PROOF HANDLE ASSY ................1........... INCLUDES ITEMS W/ #
RUBBER 20X32X28.5/52H
WASHER 11X35X4.5
BOLT 10X20 T
WASHER, LOCK M10
RUBBER, HANDLE
SOCKET HEAD BOLT 8X45 T
NUT M8
GRIP, HANDLE
RUBBER, VIB. PROOF HANDLE
BOLT, SUNK HEAD 10X20 T
NUT, VIB. PROOF HANDLE
VIB. PROOF HANDLE
2
2
2
2
2
2
2
1
2
2
2
1
52#
53#
54#
55#
56#
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
VIBRATOR ASSY.
PAGE 32 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
VIBRATOR ASSY.
NO
PART NO
PART NAME
VIBRATING CASE
BOLT 14X45 T
QTY.
1
4
4
4
1
1
1
2
8
1
1
2
2
1
1
1
REMARKS
61
418117730
001221445
030214350
031114260
418456950
060403020
418456960
418456970
002400820
418456990
418343630
040306307
040406307
418456981
951401920
952403450
002211030
953400270
953405260
418910110
*
62
63
64
65
66
67
68
69
70
71
72
72
73
74
75
77
78
79
80
WASHER, LOCK M14
WASHER, FLAT M14
CASE COVER/PULLEY
OIL SEAL TC-30458
CASE COVER/SHUT-OFF
PACKING
BOLT 8X20 SW, PW
COVER SEAL, VIB.
ECC. ROTOR SHAFT
BEARING 6307C3
BEARING 6307C4
PULLEY, VIBRATOR
KEY 7X7X30
*
*
*
*
*
*
*
*
*
*
*
*
*
*
WASHER 11X35X4.5
BOLT 10X30 H, SW
PLUG 1/4X14 10L
PACKING
1
1
1
VIBRATOR ASSY...................................... 1 ................. INCLUDES ITEMS W/
*
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER TANK ASSY.
153
152
103
104
154
154
152
102
151
101
153
109
112
107
105
108
116
91
110
111
92
113
115
114
l
92
PAGE 34 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER TANK ASSY.
NO
91
92
PART NO
PART NAME
GUARD HOOK
BOLT 10X25 H, SW
WATERTANK, ORANGE................. 1 ............ INCLUDES ITEM W/
CAP, WATER TANK
BOLT 10X30 U
WASHER 10.5X21X2 SUS.
NYLON NUT M10
COCK PT1/4, BH-1211 AL.
NUT PS-1/4
PACKING 11.5X19.5X2
PIPE HOLDER
SPRINKLING PIPE
FLANGE BOLT 8X2
WASHER, FLAT M8
NUT M8
QTY.
1
3
REMARKS
418118580
002211025
418910080
954300342
001241030
033910010
022910180
954403241
959403790
418458320
418345150
418345160
001740825
033910110
020308064
418459330
416453780
418217120
031118260
025203030
959300370
101
102
103
104
105
107
108
109
110
111
112
113
114
115
116
151
152
153
154
*
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
4
2
2
*
*
*
*
RUBBER CAP
PACKING 8X19X2T
SHAFT/CARRY
WASHER, FLAT M18
SPLIT COTTER PIN 3X30
WHEEL 200X50
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
CYLINDER HEAD ASSY.
5
11
15
11
14
7
6
14
9
12
14
4
2
12
1
14
8
10
10
3
9
l
PAGE 36 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CYLINDER HEAD ASSY.
NO. PART NO.
PART NAME
QTY. REMARKS
1%
2%
3
4%#
5
6
7
8
9
10
11
12
14
15
12204ZE1306
12205ZE1315
12210ZH8405
12216ZE5300
12251ZH1800
12310ZE1020
12391ZE1000
15721ZH8000
90013883000
90043ZE1020
90047ZE1000
9430110160
GUIDE, IN. VALVE (OS), OPTIONAL
1
GUIDE, EX. VALVE (OS) OPTIONAL........... 1 ...... INCLUDES ITEMS W/ #
HEAD COMP., CYLINDER ........................... 1 ...... INCLUDES ITEMS W/ %
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER, HEAD
GASKET, CYLINDER HEAD COVER
TUBE, BREATHER
BOLT, FLANGE (6 X 12)
BOLT, STUD ( 6 X 112)
BOLT, STUD (8 X 32)
PIN A, DOWELL (10 X 16)
BOLT, FLANGE (8 X 55)
SPARK PLUG BPR6ES (NGK)
1
1
1
1
1
4
2
2
2
4
1
957230806000
9807956846
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
CYLINDER BARREL ASSY.
15
3
2
16
19
17
7
19
10
12
17
18
1
13
9
8
11
11
14
13
9
l
PAGE 38 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CYLINDER BARREL ASSY.
NO. PART NO.
PART NAME
QTY. REMARKS
1
12000ZH8426
15510ZE1033
16510ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
90451ZE1000
90601ZE1000
90602ZE1000
91001ZF1003
91201Z0T801
91353671004
9405010000
CYLINDER BARREL ASSY. ......................... 1 ...... INCLUDES ITEMS W/ $
2
3
7
8
SWITCH ASSY., OIL LEVEL
GOVERNOR ASSY.
SLIDER, GOVERNOR
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER,THRUST (6MM)
WASHER, DRAIN PLUG (10.2MM)
CLIP, GOVERNOR HOLDER
BEARING, RADIAL BALL (6205)
OIL SEAL (25 X 41 X 6)
O-RING (14 MM)
NUT, FLANGE (10MM)
WASHER, PLAIN (6MM)
PIN, LOCK (8MM)
1
1
1
1
2
1
2
1
1
1
1
1
2
1
2
9
10
11
12
13$
14$
15
16
17
18
19
9410106800
9425108000
957010601200
BOLT, FLANGE (6 X 12)
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
CRANKCASE COVER ASSY.
l
PAGE 40 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CRANKCASE COVER ASSY.
NO. PART NO.
PART NAME
QTY. REMARKS
1
11300ZE1642
11381ZH8801
15600ZE1003
15600ZG4003
15625ZE1003
15625ZE1003
91201Z0T801
9430108140
COVER ASSY., CRANKCASE ..................... 1 ...... INCLUDES ITEMS W/
*
3
4
5
9#
10+
11
12
13
GASKET, CRANKCASE
CAP ASSY., OIL FILLER (GRAY) ................ 1 ...... INCLUDES ITEMS W/ #
CAP ASSY., OIL FILLER ............................. 1 ...... INCLUDES ITEMS W/ +
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
OIL SEAL (25 X 41 X 6)
PIN A, DOWEL (8 X 14)
BOLT, FLANGE (8 X 32)
BEARING, RADIAL BALL (6205)
1
1
1
1
2
6
1
*
957010803200
961006205000
14
*
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
CRANKSHAFT ASSY.
l
PAGE 42 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CRANKSHAFT ASSY.
NO. PART NO.
PART NAME
CRANKSHAFT
QTY. REMARKS
1
1
13310ZE1000
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
PISTON/RINGS ASSY.
l
PAGE 44 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PISTON/RINGS ASSY.
NO. PART NO.
PART NAME
QTY.
REMARKS
1
1
1
1
2
2
2
2
3
4
5
13010ZL0003
13011ZL0003
13012ZL0003
13013ZL0003
13101ZH8010
13102ZH8010
13103ZH8010
13104ZH8010
13111ZE1000
13200ZE1010
90001ZE1000
90551ZE1000
RING SET, PISTON (STD)
RING SET, PISTON (OS 0.25)
RING SET, PISTON (OS 0.50)
RING SET, PISTON (OS 0.75)
PISTON (STD)
1
1
1
1
1
1
1
1
1
PISTON (OS 0.25)
PISTON (OS 0.50)
PISTON (0.75)
PIN, PISTON
ROD ASSY., CONNECTING ................ 1 ......... INCLUDES ITEMS W/
BOLT, CONNECTING ROD
CLIP, PISTON PIN (18MM)
*
2
2
*
6
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMSHAFT ASSY.
CAMSHAFT ASSY.
2
11
12
12
14
13
15
9
10
7
1
4
4
6
17
6
8
18
7
17
16
8
18
l
PAGE 46 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO. PART NO.
PART NAME
QTY. REMARKS
1
2
4
6
7
8
9
12209ZH8003
14100ZE1812
14410ZE1010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF1000
14721ZF0000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE1010
90012ZE0010
90206ZE1000
SEAL, VALVE STEM
1
CAMSHAFT ASSY. ...................................... 1 ...... INCLUDES ITEMS W/
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, INLET
*
2
2
2
2
1
1
1
2
1
1
1
1
2
2
*
10
11
12
13
14
15
16
17
18
VALVE, EXHAUST
SPRING VALVE
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT (8MM)
NUT, PIVOT ADJ.
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOIL STARTER ASSY.
12
7
5
4
8
14
6 10
11
5
1
13
15
9
2
l
PAGE 48 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOIL STARTER ASSY.
NO. PART NO.
PART NAME
QTY. REMARKS
1
2
28400ZH8023ZB
STARTER ASSY., RECOIL .................................... 1 ..... INCLUDES ITEMS W/
*
28410ZH8003ZB
28421ZH8801
28422ZH8801
28431ZH8801
28433ZH8801
28441ZH8801
28442ZH8003
28443ZH8001
28461ZH8003
28462ZH8003
90003ZH8801
90008ZE2003
90008ZE2003
CASE, RECOIL STARTER
REEL, RECOIL STARTER
RATCHET, STARTER
PLATE, FRICTION
GUIDE, RATCHET
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
KNOB, RECOIL STARTER
ROPE, RECOIL STARTER
CLIP, CORD
BOLT, FLANGE (6 X 10)
BOLT, FLANGE (6 X 10)
1
1
2
1
1
1
1
2
1
1
1
1
1
*
4
5
*
*
6
7
*
*
8
9
*
*
10
11
12
13
14
15
*
*
*
*
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
FAN COVER ASSY.
14
6
25
2
22
16
21
17
10
20
20
20
l
PAGE 50 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
FAN COVER ASSY.
NO. PART NO.
PART NAME
QTY.
REMARKS
2
19610ZE1000ZC
COVER, FAN (BLACK)
PLATE, SIDE (OIL ALERT)
SHROUD
1
1
1
1
1
1
6
1
1
1
6
19611ZH8810
19630ZH8000
34150ZH7003
36101ZE1010
36100ZF6P81
90013883000
90022888010
90601ZH7013
957010600800
10
14
16
17
20
21
22
25
ALERT UNIT, OIL
CORD, STOP SWITCH (370MM)
SWITCH ASSY., ENGINE STOP
BOLT, FLANGE (6 X 12)
BOLT, FLANGE (6 X 20)
CLIP, HARNESS
BOLT, FLANGE (6 X 8)
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
CARBURETOR ASSY.
15
31
38
2
26
14
27
25
20
34
28
11
13
29
9
17
6
12
37
3
16
10
4
2
5
2
2
8
7
l
PAGE 52 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
2
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE0831
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH8W51
16124ZE0005
16166ZH8W50
16173001004
16211ZE1000
16212ZH8800
16220ZE1020
16221ZH8801
16610ZE1000
16953ZE1812
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030061H
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
*
3
*
4
*
5
CHAMBER SET, FLOAT ............................... 1 ...... INCLUDES O-RING
SCREW SET
SCREW SET, DRAIN ................................... 1 ...... INCLUDES GASKET
SCREW SET B ............................................ 1 ...... INCLUDES GASKET
*
6
1
*
7
*
8
*
9
CHOKE SET
1
*
10
CARBURETOR ASSY. (BE65B B) ................ 1 ...... INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
*
11
*
1
1
1
1
1
1
1
12
*
13
14
O-RING
*
INSULATOR, CARBURETOR
GASKET, INSULATOR
SPACER, CARBURETOR
GASKET, CARBURETOR
LEVER, CHOKE (STD) ................................ 1 ...... INCLUDES ITEMS W/ #
LEVER, VALVE
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN (3 X 6)
PIN, SPRING (2 X 12)
JET, MAIN (#70)
15
16
17
20
25
1
1
1
1
1
2
1
1
*
26
*
27
*
28
*
29
*
31
*
34#
37
99101ZH80700
99204ZE00350
*
38
*
JET, SET, PILOT (#35) ................................. 1 ...... INCLUDES GASKET
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR CLEANER ASSY.
10
1
4
12
2
8
10
5
3
9
7
6
7
11
11
l
PAGE 54 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR CLEANER ASSY.
NO. PART NO.
PART NAME
QTY. REMARKS
1
2
3
4
5
16271ZE1000
17210ZE1517
17218ZE1507
17230ZE1820
17232891000
17235ZE1831
17238ZE7010
17239ZE1000
17410ZE1020
90325044000
9405006000
GASKET, ELBOW
1
ELEMENT, AIR CLEANER ........................... 1 ........INCLUDES ITEMS W/*
FILTER (OUTER)
COVER, AIR CLEANER
GROMMET, AIR CLEANER
NOISE, MUFFLER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW, AIR CLEANER ............................... 1 ...... INCLUDES ITEMS W/ #
WINGNUT, TOOL BOX SETTING
NUT, CAP (6 MM)
1
1
1
1
2
1
*
*
6
7#
8#
9
10
11
12
1
2
1
957010602000
BOLT, FLANGE (6 X 20)
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
MUFFLER ASSY.
MUFFLER ASSY.
19
19
22
2
4
15
7
6
16
19
16
19
23
5
27
9
23
17
23
l
PAGE 56 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MUFFLER ASSY.
MUFFLER ASSY.
NO. PART NO.
PART NAME
QTY. REMARKS
2
18310ZH8810
18320ZF1H01
18325ZE1010
18340ZE1010
18355ZE1000
18381ZH8800
18522ZE1000
90002ZG0003
94001080000S
90050ZE1000
90055ZE1000
90055ZE1000
MUFFLER
1
1
1
1
1
1
1
2
2
4
1
4
4
5
6
7
PROTECTOR, MUFFLER
PROTECTOR, LOWER
DEFLECTOR CP
ARRESTER, SPARK
GASKET, MUFFLER
GUIDE, MUFFLER
SCREW, TAPPING (4 X 8)
NUT, HEX (8MM)
SCREW, TAPPING (5 X 8)
SCREW, TAPPING (4 X 6)
SCREW, TAPPING (4 X 6)
9
15
16
17
19
22
23
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL TANK ASSY.
12
13
14
11
18
20
24
17
28
21
27
28
7
3
l
PAGE 58 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL TANK ASSY.
NO. PART NO.
PART NAME
RUBBER, SUPPORTER (107MM)
JOINT, FUEL TANK
TANK, FUEL (BLACK)
CAP, FUEL FILLER ...................................... 1 ...... INCLUDES ITEMS W/
GASKET, FUEL FILLER CAP
FILTER, FUEL
BOLT, FLANGE (6 X 29)
WASHER (6.5 X 25 X 1.5)
O-RING (5.5 X 1.4)
QTY. REMARKS
3
16854ZH8000
16955ZE1000
17510ZE1020ZF
17620Z4H000
17631Z0T812
17672ZE2W01
90004ZH7003
90404680000
91319ME5003
91353671004
9405006000
1
1
1
7
11
12
13
14
17
18
20
21
24
27
27
28
*
1
1
1
2
2
1
2
1
1
2
*
O-RING (14 MM)
NUT, FLANGE (6MM)
FUEL TUBE (4.5 X 140)
BULK HOSE, FUEL (4.5 X 1M)
CLIP, TUBE
950014514040
950014500160M
9500202080
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
COOLING FAN AND FLYWHEEL ASSY.
l
PAGE 60 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
COOLING FAN AND FLYWHEEL ASSY.
NO. PART NO.
PART NAME
KEY, SPECIAL WOODRUFF (25 X 18)
FAN, COOLING
PULLEY, STARTER
FLYWHEEL
QTY. REMARKS
1
13331357000
19511ZE1000
28451ZH8001
31100ZE1010
90201878003
1
1
1
1
1
2
5
6
10
NUT, SPECIAL (14MM)
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
IGNITION COIL ASSY.
l
PAGE 62 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
IGNITION COIL ASSY.
NO. PART NO.
PART NAME
COIL ASSY., IGNITION
CAP ASSY.
WIRE, STOP SWITCH (370MM)
BOLT, FLANGE (6 X 25)
QTY. REMARKS
1
30500ZE1063
30700ZE1013
36101ZE1010
90121952000
1
1
1
2
2
7
11
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL ASSY.
28
5
21
7
25
18
24
3
8
23
12
26
13
17
11
25
18
24
6
10
14
20
27
20
15
16
l
PAGE 64 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL ASSY.
NO. PART NO.
3
PART NAME
QTY. REMARKS
16500ZH8U43
16551ZE0010
16555ZE1000
16561ZE1020
16562ZE1020
16571ZH8020
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16580ZH8813
16584883300
16592ZE1810
16594883010
90013883000
90015ZE5010
90114SA0000
90605230000
93500040060H
93500050160A
93500050250H
9405006000
CONTROL ASSY. ......................................... 1 ...... INCLUDES ITEMS W/
*
5
6
7
8
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
LEVER CONTROL
SPRING LEVER
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE CONTROL
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
HOLDER, WIRE
BOLT, FLANGE (6 X 12)
BOLT, GOVERNOR ARM
NUT, SELF-LOCK (6MM)
CIRCLIP
SCREW, PAN (4 X 6)
SCREW, PAN (5 X 16)
SCREW, PAN (5 X 25)
NUT, FLANGE (6MM)
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
2
1
1
1
10
11
12
13
14
15
16
17
18
20
21
23
24
25
26
27
28
*
*
*
*
*
*
*
*
*
*
*
*
*
*
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
LABELS ASSY.
2
6
7
4
l
PAGE 66 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
LABELS ASSY.
NO. PART NO.
PART NAME
MARK, OPERATOR CAUTION
EMBLEM (5.5)
MARK, CHOKE (GRAY)
MARK,THROTTLE INDICATION
QTY. REMARKS
2
4
6
7
87516ZH7000
87521ZH8030
87528ZH7000
87532ZH7000
1
1
1
1
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LIMITATIONS OF SELLER’S LIABILITY
MINIMUM ORDER
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
l
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
PAGE 68 — MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVC80VH/VHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #3 (1/13/11) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259
Fax: 310-943-2238
800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: (52) 222-285-0420 Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
Fax: 0161 339 3226
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2011, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks
are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|