OPERATION AND PARTS MANUAL
BA-SERIES
WALK-BEHIND TROWEL
EXPORT VERSION
ORIGINAL INSTRUCTIONS
MODEL #
SERIAL #
Revision #2 (03/19/04)
MULTIQUIP (UK)
HANOVER MILL
FITZROY STREET
ASHTON-UNDER-LYNE
LANCASHIRE, OL7 OTL
UNITED KINGDOM
PH. 0161-339-2223
FAX. 0161-339-3226
E-MAIL:mq@multiquip.com
www.multiquip.com
Atlanta • Boise • Newark •
Montreal, Canada • Manchester, UK
Rio De Janiero, BR • Puebla, MX
P/N 21618
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
MULTIQUIP CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
Tel. (800)-421-1244
Fax (310)-537-3927
Contact:mq@multiquip.com
MEXICO
MQ CIPSA
Carr.Fed.Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact:pmastretta@cipsa.com.mx
Tel. (52) 222-225-9900
Fax (52) 222-285-0420
UNITEDKINGDOM
MULTIQUIP (UK) LIMITED HEAD OFFICE
HanoverMill,FitzroyStreet,
Ashton-under-Lyne,
Tel. 0161 339 2223
Fax 0161 339 3226
Lancashire OL7 0TL
Contact:kcassell@multiquip.com.uk
CANADA
MULTIQUIP
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact:jmartin@multiquip.com
Tel. (450) 625-2244
Fax (450) 625-8664
BRAZIL
MULTIQUIP
Av.Evandro Lins e Silva, 840 - grupo 505
Barra deTijuca - Rio de Janeiro
RJ CEP 22631-470
Tel. 011-55-21-3433-9055
Fax 011-55-21-3433-9055
Contact:cnavarro@multiquip.com.br,srentes@multiquip.com.br
Visit our website at: www.multiquip.com
Your Local Dealer is:
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— TABLE OF CONTENTS
HONDA GX-240K1 ENGINE
Here's How To Get Help ............................................ 3
Air Cleaner Assy.................................................70-71
Camshaft Assy. ..................................................72-73
Carburetor Assy. ................................................74-75
Control Assy. ......................................................76-77
Crankcase Cover Assy. ......................................78-79
Crankshft Assy. ..................................................80-81
Cylinder Barrel Assy. ..........................................82-83
Cylinder Head Assy. ...........................................84-85
Fan Cover Assy. .................................................86-87
Flywheel Assy.....................................................88-89
Fuel Tank Assy. ..................................................90-91
Gasket Kit................................................................ 93
Ignition Coil Assy. ...............................................94-95
Muffler Assy........................................................96-97
Piston Assy. ........................................................98-99
Recoil Starter Assy.........................................100-101
Tools ...............................................................102-103
Labels ............................................................104-105
Table Of Contents ..................................................... 4
Dimensions ............................................................... 6
Specifications (Engines)............................................ 7
Specifications (Trowel Weights) ................................ 7
Training Checklist ...................................................... 8
Daily Pre-Operation Checklist ................................... 9
Safety Message Alert Symbols ..........................10-11
Rules For Safe Operation ..................................12-13
Operation And Safety Decals.................................. 14
General Information ................................................ 15
MQ WHITEMAN — BA-SERIES TROWEL
Controls and Components .................................16-17
Basic Engine ........................................................... 18
Assembly and Installation ..................................19-21
Pre-Inspection ....................................................22-23
Initial Start-Up (Gasoline Engine) ......................24-25
Operation ...........................................................26-27
Options...............................................................28-29
Maintenance ......................................................30-35
Troubleshooting (Trowel) ...................................36-37
Troubleshooting (Engine)........................................ 38
Explanation of Codes in Remarks Column ............. 40
Suggested Spare Parts ........................................... 41
Nameplate and Decals.......................................42-43
Standard Handle Assy. .......................................44-45
Quick Pitch™ Handle Assy................................46-48
Thrust Bearing Kit Assy. .....................................50-51
3 and 4 Blade spider Assy. ................................52-53
Gearbox and Engine Mounts .............................54-56
Engines, Honda, Robin, & Briggs & Stratton .....58-59
Hand Clutch Assy. ..............................................60-61
Guard Ring Assy. ...............................................62-63
Stabilizer Ring Assy............................................64-65
Blades and Adjustment Fixture Assy. ................66-67
Lifting Bale Assy. (Option) ..................................68-69
ROBIN EH25-2 ENGINE
Crankcase Assy. ............................................106-107
Crankshaft Assy. ............................................108-109
Intake and Exhaust Assy................................110-111
Governor Assy. ..............................................112-113
Cooling and Starting Assy..............................114-115
Fuel Tank Assy. ..............................................116-117
Carburetor Assy. ............................................118-119
Recoil Start Assy. ...........................................120-121
Oil Sensor Assy. .............................................122-123
Terms and Conditions of Sale — Parts ................. 124
Specifications and part
numbers are subject to
change without notice.
PAGE 4 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL— DIMENSIONS
SideView
Figure 1. BA-Series Trowel Dimensions
Table 1. BA-Series Trowel Specifications
A– Height (Lifting Hook)
B– Height Engagement Lever)
87.62 cm (34.5 in.)
104.4 cm (41.1 in.)
116.84 cm (46.0 in.)
C–Width
191.0 cm (75.2 in.)
See Table 3
97 db
D–Length
Weight – Operating
Sound Pressure
Vibration
(6.3 m/s2)
Ring Diameter
117 cm (46 in.)
3 or 4
1,478 fpm (7.5 m/s)
60 to 125
Number of Blades
Blade Tip Speed – FPM (m/s)
Rotor – RPM (Gasoline)
Path Width – cm (in.)
233 cm (48 in.)
NOTE:
1.
2.
The vibration level indicated is the maximum RMS (Root
Mean Square) value obtained at the handle grip at full
throttle on dry concrete, using a QP Handle and manual
clutch with the blades slightly pitched.Values were obtained
from all three axes of motion.The values shown represent
the maximum RMS value from these measurements.
Sound pressure is a weighted measure. Measured at the
operators ear position while the walk-behind trowel is
operating at full throttle on concrete in a manner most often
experienced in “normal” circumstances. Sound pressure
may vary depending upon the condition of the concrete.
Hearing protection is always recommended.
PAGE 6 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL— SPECIFICATIONS (ENGINES)
Table 2. Specifications (Engines)
Model
HONDA GX240K1
ROBIN EH-25-2
Air-cooled 4 stroke, Single
Cylinder, OHV,
Air-cooled 4 stroke, Single
Cylinder, OHV,
Type
Horizontal Shaft
Horizontal Shaft
Gasoline Engine
Gasoline Engine
73 mm x 58 mm
(2.90 in. X 2.30 in.)
75 mm x 57 mm
(2.95 in. x 2.24 in.)
Bore X Stroke
Displacement
Max Output
14.81 cc
15.31 cc
Engine
5.97kW (8.0 H.P.)/3600 R.P.M.
6.34kW (8.5 H.P.)/4000 R.P.M.
Approx. 6 Liters
(1.59 U.S. Gallons)
Approx. 6 Liters
(1.59 U.S. Gallons)
Fuel Tank Capacity
Fuel
Unleaded Automobile Gasoline
1.1 Liters (2-1/3 U.S. pints)
Centrifugal Fly-weight Type
Recoil Start
Unleaded Automobile Gasoline
.95 Liters (2 U.S. pints)
Centrifugal Fly-weight Type
Recoil Start
Lube Oil Capacity
Speed Control Method
Starting Method
Dimension
(L x W x H)
355 X 430 X 410 mm
(14.0 x 16.9 X 16.1 in.)
366 X 412 X 440 mm
(14.40 x 16.20 X 17.32 in.)
Dry Net Weight
25 Kg. (55.1 lbs)
23 Kg. (50.7 lbs)
Table 3. Specifications (Trowel Weights)
MODEL
BA-4-8BS
BA-4-7R
POWER SOURCE
8 HP Briggs and Stratton
7.5 HP Robin
OPERATING WEIGHT
103 kg. (228 lbs.)
107 kg. (237 lbs.)
107 kg. (237 lbs.)
110 kg. (242 lbs.)
110 kg. (242 lbs.)
SHIPPING WEIGHT
126 kg (278 lbs.)
130 kg. (287 lbs.)
130 kg. (287 lbs.)
132 kg. (292 lbs.)
132 kg. (292 lbs.)
BA-4-7RM
BA-4-8H
7.5 HP Robin, Manual Clutch
8.0 HP Honda
BA-4-8HM
8.0 HP Honda, Manual Clutch
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— TRAINING CHECKLIST
TRAINING CHECKLIST
This checklist will lists some of the minimum requirements for
machine maintenance and operation. Please feel free to detach
it and make copies. Use this checklist whenever a new operator
is to be trained or it can be used as a review for more experienced
operator’s.
TRAINING CHECKLIST
DESCRIPTION
Read Operator’s Manual completely.
NO.
OK?
DATE
1
Machine layout, location of components, checking of engine and
gearbox fluid level.
2
3
4
Fuel system, refueling procedure.
Operation of controls (machine not running).
Safety controls, Engine-Off Safety Switch operation.
Emergency stop procedures.
Startup of machine.
5
6
7
8
Maneuvering.
9
Pitching.
10
11
12
13
Concrete finishing techniques.
Shutdown of machine.
Lifting of machine (optional equipment).
Machine transport and storage.
Operator _________________________________________ Trainee __________________________________________
COMMENTS:
PAGE 8 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— DAILY PRE-OPERATION CHECKLIST
DAILY PRE-OPERATION CHECKLIST
DAILY PRE-OPERATION CHECKLIST
1
2
3
4
5
Engine Oil Level.
Gearbox Fluid Level
.
Condition of Blades
.
Blade Pitch Operation.
Clutch Operation.
Engine Shutdown Safety Switch
Operation
6
COMMENTS:
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — SAFETY MESSAGE ALERT SYMBOLS
HAZARD SYMBOLS
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand and comply with
the Safety Messages and Operating Instructions could result in
injury to yourself and others.
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
This Owner's Manual has been
developed to provide complete
instructions for the safe and
efficient operation of the MQ
Whiteman BA SERIES TROWEL.
For engine maintenance
information, please refer to the
Explosive Fuel
engine
manufacturers
instructions for data relative to its
safe operation.
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
Before using this WALK-BEHIND TROWEL, ensure that the
operating individual has read and understands all
instructions in this manual.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Burn Hazards
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. NEVER operate the engine with
heat shields or heat guards removed.
DANGER
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
WARNING
Rotating Parts
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair
and clothing away from all moving parts to
prevent injury.
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
Potential hazards associated with BA SERIES TROWEL
operation will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
PAGE 10 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine ON/OFF
switch in the OFF position, when the
trowel is not in use.
ALWAYS wear approved respiratory protection.
Over Speed Conditions
Sight and Hearing hazard
NEVER tamper with the factory settings of the
engine governor or settings. Personal injury
and damage to the engine or equipment can
result if operating in speed ranges above
maximum allowable.
ALWAYS wear approved eye and hearing
protection.
Equipment Damage Messages
Other important messages are provided throughout this manual
to help prevent damage to your trowel, other property, or the
surrounding environment.
CAUTION
This walk-behind trowel, other property, or the
surrounding environment could be damaged
if you do not follow instructions.
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — RULES FOR SAFE OPERATION
■
NEVER operate this equipment when not feeling well due to
RULES FOR SAFE OPERATION
fatigue, illness or taking medicine.
■
NEVER operate the trowel under the influence or drugs or
WARNING
alcohol.
Failure to follow instructions in this manual may lead to serious
injury or even death! This equipment is to be operated by
trained and qualified personnel only! This equipment is for
industrial use only.
■
Replace nameplate, operation and safety decals when they
become difficult to read.
■
ALWAYS check the trowel for loosened hardware such as
nuts and bolts before starting.
The following safety guidelines should always be used when
operating the BA Series.
■
NEVERtouchthehotexhaustmanifold, muffler
or cylinder. Allow these parts to cool before
servicing the trowel.
SAFETY
■
DO NOT operate or service this equipment
before reading this entire manual. The
manual must be kept available and accessible
totheoperator.
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot! components can cause serious burns.
■ This equipment should not be operated by persons under the
minimum statutory age limit.
■
The engine of this
trowel requires an adequate
free flow of cooling air.
NEVER operate the trowel
in any enclosed or narrow
area where free flow of the
air is restricted. If the air flow
is restricted it will cause
serious damage to the
engine and may cause injury
to people. Remember the
■
NEVER use this machine for any purpose other than those
described in this manual.
■
NEVER operate the trowel without proper protective clothing,
shatterproof glasses, steel-toed boots and other protective
devices required for the job.
engine gives off DEADLY carbon monoxide gas.
■ ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■
ALWAYS use extreme caution when working with flammable
liquids. When refueling, STOP the engine and allow it to cool.
■
NEVER operate the trowel in an
explosive atmosphere where fumes are
present, or near combustible materials.
An explosion or fire could result in
severe bodily harm or even death.
■
NEVER use accessories or attachments which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■
Manufacturer does not assume responsibility for any accident
due to equipment modifications. Unauthorized equipment
modification will void all warranties. Any modification which
could lead to a change in the original characteristics of the
machine should be made only by the manufacturer who shall
confirm that the machine is in conformity with appropriate
safety regulations.
■
NEVER smoke around or near the machine.
Fire or explosion could result from fuel
vapors, or if fuel is spilled on a hot! engine.
■ Topping-off to filler port is dangerous, as it tends to spill fuel.
■ NEVER use fuel as a cleaning agent.
PAGE 12 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — RULES FOR SAFE OPERATION
■
When placing the trowel inside a truck-bed for transport,
always tie-down the trowel.
■
NEVER Run engine without air filter. Severe engine damage
may occur. Service air filter frequently to prevent carburetor
malfunction.
■
ALWAYS use proper lifting techniques when moving the
trowel.
■
NEVER place your feet or hands inside the guard rings
while starting or operating this equipment.
Maintenance Safety
■
■
AVOID wearing jewelry or loose fitting clothing that may snag
on the controls or moving parts as this can cause a serious
injury.
NEVER lubricate components or attempt service on a running
trowel.
■
ALWAYS allow the trowel a proper amount of time to cool
before servicing.
■
■
ALWAYS keep clear of rotating or moving parts while
operating the trowel.
■
■
Keep the trowel in proper running condition.
Moving Parts – Shut down the engine before performing
service or maintenance functions. Contact with moving parts
can cause serious injury.
Fix damage to the trowel immediately and always replace
broken parts.
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■
ALWAYS check to make sure that the operating area is clear
before starting the engine.
DO NOT use food or plastic containers to dispose of
hazardous waste.
■
■
NEVER leave the machine unattended while running.
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using trowel.
■
ALWAYS keep the work area well organized.
Emergencies
■ ALWAYS clear the work area of any debris, tools, etc. that
would constitute a hazard while the trowel is in operation.
■ ALWAYS know the location of
the nearest fire extinguisher.
WARNING
ALWAYS check to make sure that the
operating area is clear before starting the
engine.
■ ALWAYS know the location of the
nearest and first aid kit.
■
No one other than the operator is to be in the working area
when the saw is in operation.
■
■
Always observe all applicable compulsory regulations
relevant to environmental protection, especially, fuel storage,
the handling of hazardous substances, and the wearing of
protective clothing and equipment. Instruct the user as
necessary, or, as the user, request this information and
training.
■
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information is invaluable in the case of an
emergency and could keep a serious situation from
becoming a tragic one .
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
Transporting
■
■
ALWAYS shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to prevent
fuel from spilling.
■
Drain fuel when transporting trowel over long distances or
bad roads.
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— OPERATION AND SAFETY DECALS
OPERATION AND SAFETY DECALS
The BA-Series walk-behind trowel is equipped with a number of operation,safety, and maintenance decals. Should any of these
decals become unreadable, replacements can be obtained from your dealer.
P/N 11092
P/N 2942 WHITE TEXT 13”
P/N 20936
I
C
C
U
K
H
Q
P
I
T
C
H
™
T
E
E
P
-
H
F
L
A
N
R
C
K
C
I
D
O
O
L
U
E
N
Q
O
R
C
FINISHER
BOISE, IDAHO USA
I
T
P
O
U. S. PATENT
XXXXXXX
L
E
P/N 12405
P/N: 13118
W
W
B
E
O
O
A
S
R
R
T
I
S
C
U
E
,
O
R
E
N
O
H
C
H
S
I
I
D
A
R
E
TE
I
N
F
P/N 1848
P/N 1492
P/N 1758
WARNING
To avoid injury,
you MUST read
and understand
operator’s manual
before using this
machine.
WARNING!
INJURY COULD RESULT IF FINISHER IS LIFTED
WITHOUT PITCH HANDLE FIRMLY ENGAGE
This machine to
be operated by
qualified
CLOCKWISE
BELT DRIVE
P/N 20526
personnel only.
Ask for training
as needed.
P/N 35137
WARNING!
DO NOT OPERATE HANDLE UNTIL IT IS
SECURELY FASTENED TO POWER TROWEL
& INSTRUCTIONS HAVE BEEN READ
GEAR DRIVE GEAR DRIVE
P/N 35137
CHECK
CHECK
P/N 20527
P/N 1940
CAUTION
COUNTER
CLOCKWISE
HOT
DO NOT LIFT MACHINERY BY GUARD
RING. MAY CAUSE DAMAGE TO
GUARD RING SHOCK MOUNTS
USE LIFT HANDLES ONLY
P/N1499
LIFTING POINT LIFTING POINT
PRELOAD TRIM INDICATOR
FINISH
FINISH
P/N: 1261
COMBO
COMBO
J
B
P/N 1735
LUBRICATION
LUBRICATION
P/N 36099 (ISO Blue)
WARNING
LUBRICATION
LUBRICATION
P/N: 21455
P/N: 11246
Engine exhaust and some of
its constituents,and some dust created
by power sanding, sawing, grinding,
drillingandotherconstructionactivities
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Someexamplesofthesechemicalsare:
P/N 1736
Leadfromlead-basedpaints.
Crystallinesilicafrombricks.
Cementandothermasonryproducts.
Arsenicandchromiumfromchemically
treatedlumber.
ROTATING BLADE
HAZARD
ATTENTION
PUSH PITCH CONTROL TO
FULL FORWARD POSITION
BEFORE FOLDING HANDLE
Keep hands
and feet clear
of guard rings.
Stop engine
before servicing.
P/N 35168
Your risk from these exposures varies,
dependingonhowoftenyoudothistype
of work. To reduce your exposure to
MODEL
SERIAL NO.
these chemicals: ALWAYS work in
a
well ventilated area, and work with
approved safety equipment, such as
dust masks that are specially designed
to filter out microscopic particles.
CONTACT
SERVICE DEPARTMENT
P/N 35168
P/N 10732 (WHITE TEXT)
P/N 20525
Figure 2. BA-Series Trowel Decals
PAGE 14 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— GENERAL INFORMATION
Intended Use
Spider
Operate the BA Series Trowel, tools and components in
accordance with the manufacturer's instructions. Use of any
other tools for stated operation is considered contrary to
designated use. The risk of such use lies entirely with the user.
The manufacturer cannot be held liable for damages as a result
of misuse.
The vertical output shaft of the gearbox connects to a cast hub
called the spider.The spider has either 3 or 4 arms that extend
outward that are used for attachment of blades or other
accessories. Remember as the gearbox output shaft rotates so
does the spider assembly.
Blades
BA-Series Trowel Familiarization
The blades of the trowel finish the concrete as they are rotated
around the surface. Blades are classified as combination
(203mm wide [8 in.]), float (254 mm [10 in.]) or (203 mm wide
[8 in.] ), and finish (152 mm wide [6 in.]).This trowel comes
equipped with either three or four blades per rotor equally
spaced in a radial pattern and attached to vertical rotating
shaft by means of a spider assembly.
This walk-behind trowel is designed for the floating and
finishing of concrete slabs.
Take a walk around the trowel. Take notice of all the major
components (see Figure 2, page18) like the engine, blades,
quick pitch control, air cleaner, centrifugal stop switch, etc.Check
that there is always oil in the engine.
Centrifugal Stop Switch
Read all the safety instructions carefully.Safety instructions will
be found throughout this manual and on the trowel. Keep all
safety information in good, readable condition. Operators should
be well trained on the operation and maintenance of the trowel.
In the event of a trowel runaway condition (operator releases
the handle), a centrifugal stop switch or manual clutch
depending on which trowel you have, will stop the engine
and bring the trowel to a halt.
Before using your trowel, test it on a flat watered down section of
finished concrete that is free of any debris and other objects.
This trial test run will increase your confidence in using the trowel
and at the same time it will familiarize you with the trowel’s
controls. In addition you will understand how the trowel handles
under actual conditions.
CAUTION
NEVER attempt to lift the trowel by yourself. ALWAYS get
the assistance of another person to help lift the trowel or use
a crane or lifting device to move the trowel.
Engines
This trowel is available with a 5.97kW (8.0 HP) HONDA, 6.34
kW (8.5 HP) ROBIN, or a 5.97kW (8.0 HP) Briggs and Stratton
gasoline engine. Refer to the engine owner’s manual for
instructions regarding the operation and maintenance of your
engine.The engine manual is included with your trowel at the
time of shipment from Whiteman. Please contact your nearest
Multiquip Dealer for a replacement should the original manual
disappear.
Moving the BA-Series Walk-BehindTrowel
This walk-behind trowel is designed to be moved and handled
in several ways. The easiest way to lift the trowel is to use the
auxiliary lifting tube that is attached to the main handle. See
page 24, Figure 21. When using the auxiliary tube, always use
two persons to lift the trowel.
Drive System
Power is transferred from the engine to the gearbox input shaft
via a V-belt pulley drive system. The pulley engages using a
manual clutch. See Parts section of this manual.
Some models have a lifting bale (option) installed. A strap or
chain can be attached to the lifting bale, allowing a forklift or
crane to lift the trowel up onto a slab of concrete. Use a lifting
device of adequate lifting capacity to lift the trowel.
Gearbox
The gearbox is located beneath the engine and transfers power
to the rotor or spider assembly. The gearbox controls the
rotational speed of the trowel and is equipped with two shafts
(input and output).
Training
For proper training, please use the “TRAINING CHECKLIST”
located in the front of this manual (Page 8). This checklist will
provide an outline for an experienced operator to provide training
to a new operator
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— CONTROLS AND COMPONENTS
4
5
3
6
2
1
QUICK PITCH ™
HANDLE
7
8
O
B
M
R
O
O
COMBO
TO
A
C
I
B
D
N
INDICA
H
IS
M
IN
I
FINISH
R
TRIM
O
13
B
M
D
O
A
COMBO
O
L
E
J
R
PRELOAD
H
IS
IN
FINISH
W
9
4
5
11
12
3
6
2
20
7
8
15
Figure 3. BA-Series Walk-Behind Trowels
STANDARD
HANDLE
13
14
W
18
10
16
17
PAGE 16 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— CONTROLS AND COMPONENTS
Figures 3 shows the location of the basic controls or components,
15. Engine – This trowel uses Honda, Robin and Briggs and
for the BA-Series trowel. Listed below is a brief explanation of
each control or component
Stratton type gasoline engines.
16. Trowel Arm – NEVER operate the trowel with a bent,
broken or out of adjustment trowel arm. If the blades show
uneven wear patterns or some blades wear out faster than
others, the trowel arm may need to be adjusted. Use the
trowel arm adjustment tool P/N 1817 to adjust the trowel
arms.
1.
Quick Pitch™ Control Handle – To adjust the pitch of
the blades, grasp the handle then squeeze and either move
the handle forward or backward to achieve the desired
blade pitch.
2.
Handlebar Adjuster – Change the angle/height of the
handle bars by loosening star wheel, adjust handlebars to
desired location, tighten starwheel firmly to hold handlebars
in that position.
17. Blades –This trowel is equipped with combination blades.
These blades are versatile and should take care of most
troweling needs. In addition float discs can be attached to
the trowel arms that will allow the trowel to float on "wet"
concrete.
3.
4.
Hand Grip/Handle Bar – When operating the trowel, place
both hands on each grip to maneuver the trowel. Replace
hand grips when they become worn or damaged.
18. V-Belt Cover – Remove this cover to gain access to theV-
belt. NEVER operate the trowel with this cover removed.
Throttle Control Grip – Controls the speed of the engine.
Rotate the hand grip away from the operator to increase
engine speed (high), toward the operator to decrease
engine speed (low).
20. Stabilizer Ring – Reduces trowel arm vibration. Helps
stabilize trowel arm.
5.
6.
Throttle – Controls engine speed when throttle control
grip is rotated.
Hand Grip/Handle Bar – When operating the trowel, place
both hands on each grip to maneuver the trowel. Replace
hand grips when they become worn or damaged.
7.
8.
9.
Centrifugal Engine-Off Safety Switch – In the event the
operator loses control of the trowel, this switch will shut-
down the engine.
Auxiliary LiftingTube - Use this tube to lift the trowel onto
a slab.Tube is to be inserted into socket located in front of
the gearbox.
Weights – The trowel may be equipped with two 4.5 kg
(10 lb.) weights. The weights may be removed to reduce
the operating weight of the trowel.
10. Trowel Lifting Point – Insert the auxiliary lifting tube here.
See Figure 21.
11. Pitch Control (standard models) -Turn this "Star Wheel"
clockwise for increase blade pitch, and counter-clockwise
for decrease blade pitch.
12. Clutch Lever - Clutch engagement lever.When this lever
is engaged, the blades will begin to rotate. May be used
with either Quick Pitch™ or Standard handle.
13. MainTube - When disassembling components inside the
tube exercise extreme CAUTION! Tube is spring-loaded,
severe injury could result if not disassembled correctly.
14. Guard Ring- NEVER! put hands or feet inside guard ring.
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— BASIC ENGINE
Figure 4. Engine Controls and Components
INITIAL SERVICING
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions & details of operation and servicing. The
engine shown above is a HONDA engine, operation for other
types of engines may vary somewhat.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Operating the engine without an air
filter, with a damaged air filter, or a
filter in need of replacement will
NOTE
DANGER
allow dirt to enter the engine, causing
rapid engine wear.
Adding fuel to the tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until
the fuel residue has been completely wiped
up, and the area surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap according to engine manufacturer's
instructions. Clean spark plug once a week.
9. Muffler – Used to reduce noise and emissions.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
11. Oil Drain Plug – Remove this plug to remove oil from the
engine's crankcase.
12. Dipstick/Oil Filler Cap – Remove this cap to determine if
the engine oil is low. Add oil through this filler port as
recommended in Table 3.
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
PAGE 18 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — ASSEMBLY AND INSTALLATION
Assembly and Installation
Before the trowel can be put into operation there are some
components that must be installed before the trowel can be used.
This section provided general instructions on how to install those
components. Instruction sheet P/N 20485 provides further details
for the handle assembly.
HandleTube Installation (All Models)
1.
Install the handle tube to the gearbox as shown in (Figure 5).
The mounting hardware should be contained in the shipping
container.
Figure 6. Handlebar Installation
Throttle Cable Installation (Honda and Robin Engines)
1.
Set the throttle (Figure 7) to the idle position by rotating
the grip toward the operator and away from the engine.
Figure 7. Throttle
Figure 5. HandleTube Installation
2. Feedthethrottlecablethroughthecablehousing. Makesure
the throttle indicator is on 25.4mm (1 in.).
2.
On Quick-Pitch™ models, pivot the T-handle back
(full pitch) (Figure 6). This will relax the spring inside the
handle tube. On either model, spread the handle bar ends
just enough to engage the teeth on the handle tube. Attach
the hand wheel assembly, position handlebar to desired
location, and tighten hand wheel firmly.
3. Connectthethrottlecabletotheengine. (Figure8), Honda
and (Figure 9), Robin. There should be a piece of wire
installed on the trowel to show where to route the throttle
cable. When connecting the cable housing, make sure that
no more than 6 mm (1/4 in.) of the cable housing protrudes
past the housing clamp on the engine.
THROTTLE
CABLE END
CAUTION
The Quick-Pitch™ handle is spring loaded, personal injury
or damage could result from improper handling or
installation. Be careful when installing this component.
ENGINE
THROTTLE
LEVER
SWIVEL STOP
SCREW
Considerable force may be
required when moving the Quick-
Pitch T-handle forward or
backward.
NOTE
™
CABLE
HOUSING
CLAMP
CABLE HOUSING
Figure 8. Throttle Cable Connection (HONDA)
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — ASSEMBLY AND INSTALLATION
ENGINE-OFF
SAFETY SWITCH
RED
WIRE
FROM
SWITCH
Figure 9. Throttle Cable Connection (ROBIN)
RED WIRE
FROM
ENGINE
4.
5.
Tighten cable clamp screw and swivel stop screw.
After the cable has been installed on the engine, adjust
and tighten operator position of the handle to lock the
throttle cable at the proper length.
Figure 11. Engine-Off Safety SwitchWire Connection
Pitch Cable Installation
6.
Adjust cable tension by rotating the barrel adjuster.(Figure
10)
1.
Expose the pitch cable to maximum by adjusting the handle
pitch to the "no pitch" position. On the standard model turn
the pitch control counter-clockwise, (Figure 12). On the
Quick-Pitch™ model, pivot the pitch handle forward or no
pitch, (Figure 13).
BARREL ADJUSTER
Figure 10. Barrel Adjuster
7. These are general instructions. Installation of the throttle
cable may vary for different engine configurations. Please
lookformoredetailedinstructionsinsidetheboxcontaining
thehandle.Thesemoredetailedinstructionsshouldprovide
adequate guidance for installing.
Figure 12. "No Pitch" Position (Standard)
Handle Height Adjustment
Ifhandleheightadjustmentisdesired,ahandlewedgekitcanbe
purchasedforyourtrowelbyorderingP/N2576fromyourMultiquip
dealer.These wedges are placed between the handle and the
gearbox to adjust the operating height of the handle. This kit
comes complete with wedges, new bolts and installation
instructions.Thiswillmoveyouroperatinghandlepositionupor
down approximately 76mm (3 in.).
Engine-Off Safety SwitchWire
Locate the RED wire protruding from the handle tube (Figure11)
and connect it to the RED tail wire on the engine.Test the Engine-
Off Safety Switch to insure proper operation.
Figure 13. "No Pitch" Position (Quick-Pitch™)
PAGE 20 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — ASSEMBLY AND INSTALLATION
Pre-load Adjustment (Quick-Pitch™ Models Only)
2.
3.
4.
Lock the spring in the compressed position, by releasing
the blade pitch adjustment trigger, (Quick-Pitch™ model).
1.
After the Quick-Pitch™ handle has been installed on the
trowel, spring pre-load adjustment will be required.
Remove one brass set nut from the blade pitch cable end
as shown in (Figure 14).
2.
Locate the adjustment screw on the underside of the handle
tube (Figure 16).
Thread the second brass set nut towards the cable as far
as possible.
Figure 14. Blade Pitch Cable
5.
Insert the cable end through the yoke eyelet (Figure 15)
Tighten the first brass set nut by hand to remove all the
slack from the cable.
Figure 16. Pre-load Adjustment
3.
4.
A decal has been placed on the side of the handle tube to
6
Using a wrench, tighten the second brass set nut up against
the yoke boss.This will lock the cable in place.
assist the user in the adjustment of the spring.
Align the arrow on the adjustment screw with the letter "B"
COMBO on the decal.The letter "B" stands for BA-Series
Walk-Behind trowel.
7.
Use a wrench and finish tightening the first brass set nut up
against the yoke boss.
5.
Test the pitch control operation and adjust if necessary.
YOKE
THREAD CABLE END
THROUGH YOKE EYELET
TIGHTEN SECOND
BRASS SET NUT
AGAINST YOKE BOSS
USE A WRENCH TO
TIGHTEN FIRST BRASS
SET NUT AGAINST YOKE BOSS
Figure 15. CableYoke Attachment
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— PRE-INSPECTION
DANGER
NEVER operate the trowel in a confined
area or enclosed area structure that does
not provide ample free flow of air.
CAUTION
ALWAYS wear approved eye and hearing
protection before operating the trowel.
Figure 17. Engine Oil Dipstick (Removal)
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
NEVER place hands or feet inside the guard
rings while the engine is running.ALWAYS
shut the engine down before performing any
kind of maintenance service on the trowel.
4. Iftheoillevelislow(Figure18), filltotheedgeoftheoilfiller
holewiththerecommendedoiltype(Table4).Maximum oil
capacity is 400 cc.
It is recommended that the trowel's Engine-Off Safety Switch
be used to stop the engine after every use. Doing this will verify
that the switch is working properly and presents no danger to the
operator.
Reference manufacturer engine
manual for specific servicing
instructions.
NOTE
Before Starting
1. Read safety instructions at the beginning of manual.
2. Clean the trowel, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
3. Check theairfilterfor dirtanddust. Ifairfilterisdirty,replace
air filter with a new one as required.
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
5. Checkfasteningnutsandboltsfortightness.
Figure 18. Engine Oil Dipstick (Oil Level)
Table 4. Oil Type
Engine Oil Check
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
1. Tochecktheengineoillevel,placethe trowelonsecurelevel
ground with the engine stopped.
2. Remove the filler dipstick from the engine oil filler hole
(Figure 17) and wipe it clean.
0°C or Lower
PAGE 22 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL— PRE-INSPECTION
Blade Check
DANGER
Check for worn or damaged blades. Check to see if one blade is
worn out while the others look new.If this is the case there could
be a blade pitch problem. Refer to the maintenance section of
this manual for blade pitch adjustment procedure. Replace any
worn blades.
EXPLOSIVE FUEL!
Motor fuels are highly flammable and can
be dangerous if mishandled. DO NOT
smoke while refueling. DO NOT attempt
to refuel the trowel if the engine is hot or
running.
CONTROLS
Fuel Check
Safety Engine-Off Switches
This trowel has been equipped with a safety Engine-Off switch or
a hand operated clutch. Safety Engine-Off switches or hand
clutches should be tested every time the engine is started.
1. Remove the gasoline cap located on top of fuel tank.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NEVER disable or disconnect the
NOT top-off fuel. Wipe up any spilled fuel.
Engine-Off Switch. It is provided for
NOTE
operator safety.Injury may result if it
is disable, disconnected or
improperly maintained.
Gearbox Oil
1.
Determine if the gearbox oil is low by removing the oil
plug located on the side of the gearbox. This plug will be
marked by the "check" decal. See Figure 19.The correct
level of the lubrication oil should be to the bottom of the fill
plug.
CentrifugalType Engine-Off Switch
(Figure 20) The switching mechanism of this switch should
operatefreelyandshouldalwaysbekeptinthiscondition.With
theswitchintheOFFposition,theengineshouldnotstartorrun.
The purpose of this switch is to stop the engine in a runaway
situation,(i.e.-theoperatorreleasingthehandleduringoperation).
GEARBOX
OIL SIGHT/
FILL PLUG
DRAIN
PLUG
Figure 19. Gearbox
2.
3.
If lubrication oil begins to seep out as the drain plug is
being removed, then it can be assumed that the gearbox
has a sufficient amount of oil.
Figure 20. Centrifugal Engine-Off Switch
Hand Clutch
If lubrication oil does not seep out as the drain plug is
being removed, fill with type ISO 680 (Whiteman P/N 10139)
gearbox lubricant oil until the oil filler hole overflows.
Some finisher models are equipped with a hand operated
clutch. These units are not equipped with an Engine-Off Switch.
The unit automatically stops rotating when the clutch lever is
released.
V-belt Check
DO NOT let the machine sit unused with the engine at high speed
for an extended period of time. It will cause premature belt wear
or may destroy the belt. Always set the engine speed to idle when
the hand clutch is disengaged.
A worn or damagedV-belt can adversely affect the performance
of the trowel.If aV-belt is defective or worn simply replace theV-
belt as outlined in the maintenance section of this manual.
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — INITIAL START-UP
This section is intended to assist the operator with the initial
start-up of the walk-behind trowel. It is extremely important that
this section be read carefully before attempting to use the trowel
CAUTION
The trowel is heavy and awkward to move around. Use
proper heavy lifting procedures and DO NOT lift the trowel
by the guard rings.
in the field.
DO NOT use your trowel until this section is thoroughly
understood.
Lifting theTrowel Onto a Slab.
Auxiliary Lifting Tube
CAUTION
DO NOT attempt to operate the trowel until the Safety,
General Information and Inspection sections of this manual
have been read and thoroughly understood. Depending on
engine manufacturer, operating steps may vary.See engine
manufacturer's operating manual. The following start-up
procedure makes reference to a HONDA 5.97 kW (8 HP)
Engine (Manual Start).
Removetheauxiliaryliftingtubelocatedontopofthemainhandle.
Insert the tube into the socket located on the opposite side of the
gearbox (Figure 21) from the handle.
Make sure that the hole in the tube engages with the pin in the
socket. With one person lifting from the main handle, and another
lifting from the auxiliary lifting tube pick up the machine to move
onto a slab.
Starting the Engine (HONDA engine)
1. Place the engine fuel valve lever (Figure 22) to the "ON"
position.
Figure 21. Lifting the Trowel
Figure 22. Engine FuelValve Lever
CAUTION
The trowel must be stabilized by the person carrying the
operator’s handle (Figure 21). If it is not stabilized properly
the handle may swing around and flip the trowel, thus causing
damage to the trowel and bodily injury.
2. Rotate the throttle (Figure 23) to the "idle" position.
Lifting Bale (Option)
The lift bale is optional on new trowels. It provides an optimal lift
point for moving the trowel. Lift bales or forklift can be used to
lift a trowel up onto a building with a crane. See “Optional
Equipment” section in this manual for ordering information.
Using a crane to move a machine with a lift bale is highly
recommended, and is perfectly safe for the machine. Extra care
should be taken when lifting the machine off the ground, though.
Serious damage to the machine or personal injury could be
caused by dropping a trowel.
Figure 23. Throttle (Idle Position)
PAGE 24 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — INITIAL START-UP
3. Placethecentrifugal Engine-Offswitch(Figure24)inthe
"ON" position. For models that use this feature.
WARNING
NEVER disable or disconnect the centrifugal Engine-Off
switch. It is provided for the operators’ safety and injury may
result if it is disabled, disconnected or improperly maintained.
Figure 26. Starter Grip
6. If the engine has started, slowly return the choke lever
(Figure 25) to the CLOSED position. If the engine has not
started repeat steps 1 through 5.
7. Before the trowel is placed into operation, run the engine for
several minutes. Check for fuel leaks, and noises that would
associate with a loose guard ring and/or covers.
Figure 24. Centrifugal Engine-Off Switch
8. To begin troweling, rotate the throttle (Figure 27) toward the
"RUN" position.
4. Place theChokeLever(Figure25)inthe"OPEN "position
Figure 27. Throttle (Run Position)
Figure 25. Engine Choke Lever
5. Grasp the starter grip (Figure 26) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — OPERATION
Maneuvering the Trowel
The following steps are intended as a basic guide to machine
operation, and are not to be considered a complete guide to
concrete finishing. We suggest that all operators (experienced
and novice) read “Slabs on Grade” published by the American
Concrete Institute, Detroit, Michigan. Read the “Training”
section of this manual for more information.
1. Get into the operator’s position behind the handle. With a
secure foothold and a firm grasp on the handles slowly
increase the engine speed until the desired blade speed is
obtained.
If your trowel has a hand clutch (Figure 30), set your engine
speed with the throttle, then pull on the hand clutch lever to
startthebladesturning. Adjustthebladespeedafterthehand
clutch is fully engaged.
PitchingThe Blades
Quick Pitch Handle
1. To pitch the blades upwards using the "Quick-Pitch™"
T-handle, (Figure 28) simply squeeze the trigger lock
and pull the T-handle towards the operator. Pushing
theT-handle towards the engine will cause the blades
to lay flat.
Figure 30. Hand Clutch Lever
2. To maneuver the trowel, gently lift up on or press down on the
main trowel handle. To move the machine to the operator’s
left, lift up on the handle, to move machine to the right, push
down on the handle.
Figure 28. Quick-Pitch™ T- Handle
Standard Handle
3. The best method for finishing concrete is to slowly walk
backwards (Figure 31) with the trowel, guiding the trowel
from side to side.This will cover all footprints on wet concrete.
1. To pitch the blades upwards using the "Standard" handle,
(Figure29)simplyturnthestar-wheelclockwise.Turningthe
starwheelcounterclockwise willcausethebladestolayflat.
4. Remember that if you let go of the trowel, just step away and
let the trowel come to a complete stop before trying to recover
the trowel.
Figure 29. Standard Handle
PAGE 26 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — OPERATION
Continue to practice maneuvering the trowel.Try to practice as if
you were finishing a slab of concrete. Practice edging and
covering a large area. Remember a good finishing technique is
to work backwards. Be careful when moving backwards so that
hazards can be avoided.The best way to get accustomed to the
trowel is repeated use.
Figure 32 below illustrates a typical walk-behind trowel
application.Practice maneuvering the trowel.The trick is to "let
the trowel do the work".
Figure 31. Maneuvering The Trowel
CAUTION
CAUTION
NEVER place your feet or hands inside the guard rings
while starting or operating this equipment.
ALWAYS keep clear of rotating or moving parts while
operating this equipment.
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — OPTIONS
Clip-On Float Blades (Optional)
Blades
These blades will clip (Figure 34) on to an existing installed blade,
allowing your finisher to float on “wet” concrete so that the
troweling operation can begin as early as possible. They are
easily removable, so that after the floating operation, when the
concrete is sufficiently cured, they can be removed to expose the
finish blades for continued troweling.
Blades should be changed when
they fail to finish concrete in a
satisfactory manner.
NOTE
Blades are a vital part of finishing concrete. This trowel, or
finisher, has been designed to finish concrete and the blades are
built to stringent quality standards out of the finest trowel steel. If
you need replacement blades, consult your parts list in this
manual for part numbers and order them from your Multiquip parts
dealer or importer.
Figure 34. Clip-On Float Blade
Float Discs (Optional)
Combo Blades
This trowel was equipped with combination float/finish (Figure
32) blades as original equipment. These blades have been
designed for optimum performance in both the floating and
finishing operations. These blades are versatile and should take
care of most troweling needs.
These round discs (Figure 35) attach to the spiders and allow the
machine to “float” on “wet” concrete.The disc design allows early
floating and easy movement from wet to dry areas.They are also
very effective in embedding large aggregates and surface
hardeners.
Figure 32. Combination Blade
Finish Blades (Optional)
These blades (Figure 33) have been specifically designed for
finish operations with this trowel. They will provide a premium
surface finishing capability from your trowel.They should only be
used after the concrete has set to the point where the trowel does
not sink into the concrete when placed on it.
Figure 35. Float Disk
Figure 33. Finish Blade
PAGE 28 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — OPTIONS
Trowel Arm Adjustment Tool
Grinding Attachments
If blades show uneven wear patterns or some tend to wear out
faster than others, the trowel arms may need to be adjusted.
Whiteman makes a special tool (Figure 38) that will adjust all of
the trowel arms consistently.The Trowel Arm Fixture P/N is 1817.
Available grinding attachments are used for grinding surface
imperfectionsorjoints.Theseattachmentsallowgreaterutilization
ofyourtrowel.Figure36illustratesatypicalgrindingdiskassembly,
complete with hub and stone mounting plate.
Figure 38.Trowel Arm Adjustment Fixture
Figure 36. Grinding Disk
Lifting Bale
There is a heavy duty, center balance type lifting bale (Figure 37)
made specifically for your trowel. These bales are ideal for lifting
and transporting your trowel.They are designed to lift the finisher
and balance it on it’s center of gravity, providing great stability
while lifting.This option is not available on electric trowel models.
Figure 37. Lifting Bale
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — MAINTENANCE
The following procedure should be
followed to adjust trowel arms when
it becomes apparent that the trowel
is finishing poorly or in need of
routine maintenance.
See the engine manual supplied with
your machine for appropriate engine
maintenance schedule and
troubleshooting guide for problems.
NOTE
NOTE
Trowel Arm Adjustment Procedure
At the front of the book (Page 7) there is a “Daily Pre-Operation
Checklist ”. Make copies of this checklist and use it on a daily
basis.
A level, clean area to test the trowel prior to and after is essential.
Any unlevel spots in the floor or debris under the trowel blades
will give an incorrect perception of adjustment.Ideally, a 13 cm x
13 cm (5 x 5 in.), 19 mm (3/4 in.) thick flat steel plate should be
used for testing.
WARNING
ALWAYS disconnect spark plug and secure away from the
engine before performing service or maintenance.
1. To determine which blades need adjustment, place the
trowelinthetestarea(three-quarterinchthickplate)andlook
for the following conditions:
■
Pitch the blades as flat as possible and look at the
adjustment bolts.They should all barely make contact
with the lower wear plate on the spider. If you can see
that one of them is not making contact, some adjustment
will be necessary.
CAUTION
ALWAYS allow the engine to cool before
servicing. NEVER attempt any maintenance
work on a hot! engine.
■
Is the machine wearing out blades unevenly (i.e. one
blade is completely worn out while the others look new)?
MAINTENANCE SCHEDULE
Daily (8-10 Hours)
Figure 39 below illustrates a "worn spider bushings or bent
trowel arms". Check to see that adjustment bolt is barely
touching (.25 mm [.010 in.] max. clearance) lower wear plate. All
alignment bolts should be spaced the same distance from the
lower wear plate.
1.
Check the oil level in the engine crankcase and gear box,
fill as necessary.
2.
CheckV-belt.
Weekly (50-60 Hours)
1.
2.
3.
Relube arms, thrust collar and clutch.
Replace blades if necessary.
Check and clean or replace the engine air filter as
necessary.
4.
Replace engine oil and filter as necessary, see engine
manual.
Figure 39. Worn Spider Plate
Figure 40 below illustrates the "correct alignment " for a spider
plate (as shipped from the factory).
Monthly (200-300 Hours)
1.
Remove, clean, reinstall and relube the arms and thrust
collar.Adjust the blade arms.
2.
Remove, clean, reinstall clutch.
Yearly (2000-2500 Hours)
1.
Check and replace if necessary the arm bushings, thrust
collar bushings and shaft seals.
2.
3.
Check pitch control cables for wear.
Adjust blade speed.
Figure 40. Correct Spider Plate Alignment
PAGE 30 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — MAINTENANCE
2. Start engine, and bring trowel blades up to full speed and look
forthefollowingconditions:
b. Loosen the jam nut and cone point square head set
screw,andcarefullylifttheuppertrowelassemblyoff
ofthespiderassembly. Aslighttapwitharubbermallet
maybenecessarytodislodgethespiderfromthemain
shaftofthegearbox.
■
Does the trowel have a perceived rolling or bouncing
motion when in use?
■
Look at the trowel while it is running, does the guard
ring “rock up and down” relative to the ground?
c. If the trowel is equipped with an outer stabilizer ring
(Figure 42), remove the four bolts at the end of each
spiderarm.
Spider Removal
1. Onceitisdeterminedthatanadjustmentisrequired,remove
the spider assembly from the gearbox shaft as follows:
a. Locate the cone point square head set screw (Figure 41)
and attached jam nut found on the side of the spider
assembly.
Figure 42. Stabilizer Ring
d. Examinestabilizerringforoutofroundorbends.Ifring
isdamaged,replacering.Ifringisfoundtobecorrectwith
no damage, set aside.
Trowel Arm Removal
1. Each trowel arm is held in place at the spider plate by a hex
headbolt (zerkgreasefitting)andarollpin.Removeboththe
hex head bolt and the roll pin (Figure 43) from the spider
plate.
2. Remove the trowel arm from the spider plate.
Figure 41. Spider/Gearbox Removal
Figure 43. Removing Roll Pin
and Zerk Grease Fitting
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — MAINTENANCE
Trowel Arm FlatnessTest
3. Should the trowel arm inserts (bronze bushing ) come out
withthetrowelarm,removethebushingfromthetrowelarm
andsetasideinasafeplace.Ifthebushingisretained inside
the spider plate, carefully remove the bushing.
1. Usingapieceof19mm (3/4in.)thicksteelplateoranysurface
whichistrueandflat,checkallsixsidesofeachtrowelarm
forflatness.
4. Examine the bronze trowel arm bushing insert (Figure 44),
cleanifnecessary.Replacebushingifoutofroundorworn.
2. Check each of the six sides of the trowel arm (hex section
only) using a ten thousands of an inch (max.) feeler gauge
(Figure 46) between the flat of the trowel arm and an ex-
tremelyflat testsurface.
Figure 44. Bronze Bushings
Trowel Blade Removal
WARNING
ALWAYS disconnect spark plug and secure away from the
engine before performing service or maintenance.
1. Removethetrowelbladesfromthetrowelarmbyremoving
thethreehexheadbolts(Figure45)fromthetrowelarm.Set
blades aside.
Figure 46. Trowel Arm FlatnessTest
3. If the trowel arm is found to be uneven or bent, replace the
trowelarm. Abenttrowelwillnotallowthetroweltooperate
in a smooth fluid rotation.
4. Next,checkeachofthesixsidesof theroundmachinedshaft
sectionofthetrowelarm.Eachsectionshouldhavethesame
clearance betweentheroundofthetrowelarmshaftandthe
testsurface.
Trowel arms can be damaged by
rough handling or by striking
exposed plumbing or forms while in
Figure 45. Trowel Blades
NOTE
operation. ALWAYS look-out for
objects which might cause damage
to the trowel arms.
2. Wirebrushanybuild-upofconcretefromallsixsidesofthe
trowel arm. Repeat this for the remaining three arms.
PAGE 32 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — MAINTENANCE
Trowel Arm Adjustment
3. Un-screwthelockingboltsontheadjustmenttool,andplace
thetrowelarmintotheadjustmentfixturechannelasshown
Shown in Figure 47 is the adjustment fixture with a trowel arm
inserted. As each trowel arm is locked into the fixture, the arm bolt
is adjusted to where it contacts a stop on the fixture. This will
consistently adjust all of the trowel arms, keeping the finisher as
flat and evenly pitched as possible.
inFigure48. Athinshimmayberequiredtocovertheblade
holes on the trowel arm. Make sure to align the trowel
adjustmentboltwiththefixtureadjustmentbolt.
4. Using an allen wrench, tighten the locking bolts on the
adjustment tool and securely lock the trowel arm in place.
1. Locate the trowel arm adjustment tool P/N 1817. Set the
adjustmenttoolfora clock-wisebladerotation,meaningthe
fixture arm is in the "UP" position.
5. Loosenthelockingnutonthetrowelarmlever,thenturnthe
trowel arm adjusting bolt until it barely touches (.25 mm
[.010in.]) the adjusting bolt on the fixture.
6. Afterthecorrectadjustmenthasbeenmade,tightenlocknut
on trowel arm lever to lock in place.
7. Loosen locking bolts on adjustment fixture, and remove
trowelarmfromfixture.
8. Repeat steps 2-7 for the remaining trowel arms.
Re-Assembly
1. Clean and examine the upper/lower wear plates and thrust
collar.Examine the entire spider assembly.Wire brush any
concreteorrustbuild-up.Ifanyofthespider componentsare
found to be damaged or out of round, replace them.
2. Makesurethatthebronzetrowelarmbushingisnotdamage
oroutofround.Cleanthebushingifnecessary.Ifthebronze
bushing is damage or worn, replace it.
3. Reinstall bronze bushing onto trowel arm.
4. Repeat steps 2 -3 for each trowel arm.
5. Makesurethatthespringtensionerisinthecorrectposition
to exert tension on the trowel arm.
6. Insertalltrowelarmswithleversintospiderplate(withbronze
bushingalreadyinstalled)usingcaretoaligngreaseholeon
bronze bushing with grease hole fitting on spider plate.
7. Lock trowel arms in place by tightening the hex head zerk
grease fitting and jam nut.
Figure 47. Trowel Arm AdjustmentTool
8. Re-install the blades back onto the trowel arms.
9. Install stabilizer ring onto spider assembly.
2. TrowelsmanufacturedpriortoJuneof1982requirethatthe
distancefromtheendoftheadjustingboltandthefixturearm
must be 22 mm (7/8 in.) (Figure 48). Conversely, trowels
manufactured after June of 1982 require that the distance
fromtheendoftheadjustingboltandthefixturearmmustbe
13 mm (1/2 in.).
10. Reinstall lower wear plate, thrust collar and upper wear
ringinthereverse order thattheyweredis-assembledonto
the spider shaft. Make sure that there is little or no lateral
movement between the thrust collar and the spider shaft.
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — MAINTENANCE
Hand Clutch - Optional CE Compliant Trowels
11. Carefully lift the upper trowel assembly, line up the key-
wayongearboxmainshaftandinsertintospiderassembly.
CEcomplianttrowels are equippedwithoneoftwotypesof hand-
operatedclutchesinsteadofanautomaticcentrifugalclutch. Both
arebelt-tightenertypeclutchesandoperatebyremovingslackin
the V-belt which then transmits power from the engine to the
gearbox.
12. Reinstall square head cone point into spider plate and
tighten in place.Tighten jam nut. Use care in making sure
point of set screw engages groove in gear box main shaft.
13. Lubricate all grease points (zerk fittings) with premium
"Lithum 12" based grease, conforming to NLG1 Grade #2
consistency.
There are two reasons to adjust the hand clutch: 1) operator
comfort;2)initialbeltstretchandbreak-in.
The easiest and most simple adjustment is to adjust the clutch
cablehousingusingtheadjustmentnut(Figure48)locatedonthe
clutch lever. Rotating the nut provides either more or less
(depending upon the direction of rotation) clutch engagement.
Testing
1. Place trowel in test area, start engine and test trowel for
smoothness.
2. If trowel bounces has excessive vibration or does not run
smoothlyrepeatalignmentprocedure.
Changing a Blade
Whiteman recommends that all the blades be changed at the
same time.The machine may wobble or bounce if only some of
the blades are changed at one time.
Figure 48. Hand Clutch Adjustment
Hand Clutch Disengagement
WARNING
ALWAYS disconnect spark plug and secure away from the
engine before performing service or maintenance.
1. Startthetrowelasoutlinedinthe"InitialStart-up"sectionin
this manual. Move the throttle lever so that the engine is
running about 1/4 to 1/3 of full speed.
1. Place the machine on a flat, level surface. Adjust the blade
pitchcontroltomakethebladesasflataspossible.Notethe
blade orientation on the trowel arm.
2. Gripthetrowelhandlefirmlyandcarefullyengagetheclutch
bysqueezingtheclutchlevertowardthehandlewithyourleft
hand.Afterthetrowelisstabilizedandyoufeelcomfortable
with its operation, use your right hand to adjust the housing
adjustmentnut.
Before removing the blades,
NOTE
please note the orientation of the
blade on the trowel arm.
3. Rotating the nut so that it backs out of the lever housing
increases the engagement and also the squeezing force
required to keep it engaged.
1. Remove the three bolts and lock washers that secure the
blade to the trowel arm. Remove the blade.
Too much squeezing force may cause premature hand
fatigue. Too little squeezing force may cause belt slippage
and premature belt wear. Each operator should experiment
with the adjustment to get the optimum combination of
squeeze force and belt grip.
2. Usingawirebrush,scrapeallconcreteparticles andforeign
debris from the trowel arm.
3. Install the new trowel blade onto the trowel arm. Make sure
blade is installed correctly, maintaining the proper orienta-
tion for direction of rotation.
4. After initial break-in (approximately 8 hours) the above
procedure should be repeated to attain optimum operator
comfort and belt wear.
4. Reinstall the three bolts and lock washers that secure the
blade to the trowel arm.Tighten all three bolts securely.
5. After considerable belt wear, the adjustments mentioned
abovemayhavealittleornoeffectonclutchengagement.If
this is the case, the belt should be replaced.
5. Repeat steps 1-4 for all remaining blades.
PAGE 34 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — MAINTENANCE
1. Lower finisher onto pan with blades (item #1) adjacent to Z-
Clips (item #4).
Installing Pans Onto Finisher Blades
2. Rotate blades into position under Z-Clips. Ensure that the
blades are rotated in the direction of travel when the machine
is in operation or use the engine to rotate the blades into
position.
3. Attach the blade tie-downs (item #3) to the far side of the Z-
Clip brackets (item #4) with tie-down knobs (item #2) as
shown in figure 49.
4. Check to make certain that the blade edges are secured
under the Z-Clips and the tie-downs are secured completely
overtheedgesofthebladebarbeforethemachineisputback
into operation.
WARNING
ALWAYS install pans either on the work area or on an area
that is next to and level with the work area. DO NOT lift the
trowel when the pans are attached.
Refer to Figure 49 when installing pans onto finisher blades.
2
3
1
4
1
2
3
4
BLADE ASSEMBLY
KNOB, TIE DOWN Z-CLIP PANS
TIED OWN, BLADE
Z-CLIP, PAN
Figure 49. Pan Installation
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — TROUBLESHOOTING (TROWEL)
TABLE 6. TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Make sure that the Engine-Off switch is ON or replace switch if
necessary.
Engine-Off switch malfunction?
Engine running rough or not at
all.
Look at the fuel system. Make sure there is fuel being supplied to
the engine. Check to ensure that the fuel filter is not clogged.
Fuel?
Check to ensure that the ignition switch has power and is
functioning correctly.
Ignition?
Other problems?
Consult engine manufacturer’s manual.
Check wiring. Replace as necessary.
Loose wire connections?
Safety Engine-Offl switch not
functioning.
Bad contacts?
Replace switch.
Make certain blades are in good condition, not excessively worn.
Finish blades should measure no less than 2" (50mm) from the
blade bar to the trailing edge, combo blades should measure no
less that 3.5" (89mm). Trailing edge of blade should be straight
and parallel to the blade bar.
Blades?
Check that all blades are set at the same pitch angle as
measured at the spider. A field adjustment tool is available for
height adjustment of the trowel arms (see Optional Equipment).
Spider?
Check the spider assembly for bent trowel arms. If one of the
arms is even slightly bent, replace it immediately.
Bent trowel arms?
If trowel “bounces, rolls
concrete, or makes uneven
swirls in concrete”.
Check the trowel arm bushings for tightness. This can be done by
moving the trowel arms up and down. If there is more than 1/8"
(3.2 mm) of travel at the tip of the arm, the bushings should be
replaced. All bushings should be replaced at the same time.
Trowel arm bushings?
Check the flatness of the thrust collar by rotating it on the spider.
If it varies by more than 0.02" (0.5 mm) replace the thrust collar.
Thrust collar?
Check the thrust collar by rocking it on the spider. If it can tilt
more than 3/32" (2.4 mm) [as measured at the thrust collar O.D.],
replace the bushing in the thrust collar.
Thrust collar bushing?
Thrust bearing worn?
Check the thrust bearing to see that it is spinning free. Note:
Thrust cap, replace if necessary.
The main output shaft of the gearbox assembly should be
checked for straightness. The main shaft must run straight and
cannot be more than 0.003" (0.08 mm) out of round at the spider
attachment point.
Main shaft?
Machine has a perceptible
rolling motion while running.
Check to make sure that both fingers of the yoke press evenly on
the wear cap. Replace yoke as necessary.
Yoke?
Check to ensure that each blade is adjusted to have the same
pitch as all other blades. Adjust per maintenance section in
manual.
Blade Pitch?
PAGE 36 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — TROUBLESHOOTING (TROWEL)
TABLE 6. TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Worn V-belts?
SOLUTION
Replace V-belt.
Dirty centrifugal clutch?
Disassemble and clean clutch.
Defective or worn out
centrifugal clutch?
Replace entire clutch.
Clutch slipping or sluggish
response to engine speed
change.
Hand clutch out of adjustment?
Adjust per instructions in maintenance section of this manual.
Replace parts as necessary.
Worn or defective hand clutch
parts?
Rotate input shaft by hand. If shaft rotates with difficulty, check
the input and output shaft bearings. Replace as necessary.
Worn bearings in gearbox?
Worn or broken gears in
gearbox?
Verify that the gearbox shaft rotates when the input shaft is
rotated. Replace both the worm and worm gear as a set.
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — TROUBLESHOOTING (ENGINE)
TABLE 7. TROUBLESHOOTING (ENGINE)
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or
replace spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace
switch.
Replace ignition coil.
Set correct spark gap and
clean points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirty?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Close Choke.
Difficult to start, "fuel is available, spark
is present and compression is normal".
Choke Open?
Suction/exhaust valve stuck or protruded?
Re-seat valves.
Replace piston rings and or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low".
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fuel filter clogged?
Fill with correct type of fuel.
Replace fuel filter.
No fuel present inside priming bulb.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
PAGE 38 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — EXPLANATION OF CODES IN REMARKS COLUMN
How to read the marks and remarks used in this parts book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
All parts with same symbol in the number column, , #,
, belong to the same assembly or kit.
+
, %, or
*
■
If more than one of the same
reference number is listed, the last
one listed indicates newest (or latest)
part available.
NOTE
NOTE
The contents of this parts catalog
are subject to change without
notice.
PAGE 40 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — SUGGESTED SPARE PARTS
BA-SERIES TROWEL 1 TO 3 UNITS WITH
HONDA GX-240K1 ENGINE.
BA-SERIES TROWEL 1 TO 3 UNITS WITH
ROBIN EH25-2 ENGINE.
1 to 3 Units
1 to 3 Units
Qty......... P/N.............................. Description
3 ............ 20478 .................... GRIP
Qty......... P/N.............................. Description
3 ............ 20478 .................... GRIP
2 ............ 20856 .................... SAFETY SWITCH
1 ............ 20285 .................... CABLE STANDARD HANDLE
1 ............ 20297 .................... CABLE QUICK-PITCH™
1 ............ 20435 .................... THROTTLE CABLE
4 ............ 1157 A .................. BUSHING
2 ............ 20856 .................... SAFETY SWITCH
1 ............ 20285 .................... CABLE STANDARD HANDLE
1 ............ 20297 .................... CABLE QUICK-PITCH™
1 ............ 20435 .................... THROTTLE CABLE
4 ............ 1157 A .................. BUSHING
1 ............ 2828...................... ARM (298 mm [11-3/4 in.])
4 ............ 1162 A .................. LUBE CAP
1 ............ 2828...................... ARM (298 mm [11-3/4 in.])
4 ............ 1162 A .................. LUBE CAP
4 ............ 1167 A .................. SCREW
4 ............ 1456...................... NUT
4 ............ 1167 A .................. SCREW
4 ............ 1456...................... NUT
4 ............ 1875...................... WASHER
4 ............ 1322...................... SCREW
4 ............ 1875...................... WASHER
4 ............ 1322...................... SCREW
1 ............ 21046 .................... GASKET KIT
1 ............ 21047 .................... BEARING KIT
4 ............ 1247...................... RUBBER GROMMET
4 ............ 1245...................... SPACER
1 ............ 21046 .................... GASKET KIT
1 ............ 21047 .................... BEARING KIT
4 ............ 1247...................... RUBBER GROMMET
4 ............ 1245...................... SPACER
1 ............ 2827...................... ARM (419 mm [16-1/2 in.])
2 ............ 0261...................... BELT (A-31) HONDA
2 ............ 0262...................... BELT (A-33) HONDA W/HANDCLUTCH
1 ............ 10968 .................... THRUST COLLAR KIT
2 ............ 9807955846 .......... SPARK PLUG HONDA
2 ............ 17620ZH7023 ....... TANK CAP (HONDA)
2 ............ 17210ZE2505 ....... AIR CLEANER ELEMENT (HONDA)
2 ............ 17218ZE2505 ....... FILTER OUTER (HONDA)
1 ............ 2827...................... ARM (419 mm [16-1/2 in.])
2 ............ 0152 1 ................... BELT (A-30) (ROBIN)
1 ............ 10968 .................... THRUST COLLAR KIT
2 ............ 0650140031 .......... SPARK PLUG (ROBIN)
2 ............ 0430430015 .......... TANK CAP (ROBIN)
2 ............ 2703261008 .......... AIR CLEANER ELEMENT (ROBIN)
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — NAMEPLATE AND DECALS
NAMEPLATES AND DECALS
3
2
4
1
QUICK PITCH ™
HANDLE
5
O
B
R
M
O
O
COMBO
TO
A
IC
B
D
INDICA
H
IS
IN
IM FINISH
R
TRIM
8
9
O
B
M
D
O
A
COMBO
O
L
E
J
R
PRELOAD
H
6
IS
IN
FINISH
7
W
12
STANDARD
HANDLE
11
10
13
14
15
16
W
17
19
18
PAGE 42 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO.
1
PART NO.
1758
PART NAME
DECAL: QUICK-PITCH™ HANDLE
QTY. REMARKS
1
2
12405
DECAL: QUICK-PITCH™ HANDLE INSERT
2
3
20527
20526
2942
1736
1735
DECAL: QUICK-PITCH™WARNING .................1....... SAFETY ITEM
DECAL: QUICK-PITCH™ LATCH WARNING ....... 1 ....... SAFETY ITEM
4
5
6
7
8
9
DECAL: MQ WHITEMAN 13"
DECAL: ARROWS
DECAL: PRE-LOAD INDICATOR
1
1
1
11246
DECAL: OIL CHECK ............................................. 1 ....... PART OF DECAL KIT P/N 12620
NAMEPLATE.......................................................... 1 ....... CONTACT MULTIQUIP
.......................................................................................... SERVICE DEPT.
10
11
12
1940
11092
11246
DECAL: MQ WHITEMAN (SMALL)
DECAL: CE
DECAL: GEAR DRIVE .......................................... 1 ....... SAFETY ITEM,
1
1
.......................................................................................... PART OF DECAL KIT P/N 12620
13
14
1492
1147
DECAL: STANDARD HANDLE (FINISHER)
1
DECAL: HELMET, FOOT AND GLOVE ................. 1 ....... SAFETY ITEM,
.......................................................................................... PART OF DECAL KIT P/N 12620
DECAL: HOT ......................................................... 1 ....... SAFETY ITEM,
.......................................................................................... PART OF DECAL KIT P/N 12620
DECAL: DO NOT LIFT .......................................... 1 ....... SAFETY ITEM
15
11246
16
17
18
19
1261
1848
2938
11246
DECAL: POWER TROWEL
DECAL: METRIC
1
1
DECAL: BELT DRIVE ........................................... 1 ....... SAFETY ITEM,
.......................................................................................... PART OF DECAL KIT P/N 12620
DECAL: WARNING, READ MANUAL .................... 1 ....... SAFETY ITEM
DECAL: WARNING, ROTATING BLADE HAZ........ 1 ....... SAFETY ITEM
DECAL: WARNING, LIFTING/CRUSH HAZ........... 1 ....... SAFETY ITEM
20
21
22
35137
35168
21455
SEE DECAL ILLUSTRATIONS ON PAGE 12
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — STANDARD HANDLE
STANDARD HANDLE
40
3
4
21
5
7
8
6
22
9
10
14
18
DETAIL “A”
17
43
16
11
42
44
15
19
20
2
SEE
DETAIL “B”
21
22
23
27
24
39
SEE
1
DETAIL “A”
12
3
13
30
25
26
31
ASM
41
32
38
12
3
37
33
2
28
1
36
35
29
DETAIL “B”
APPLY THREAD LOCK (LOCTITE
242 BLUE OR EQUIVALENT).
1
PART OF ENGINE ASSEMBLY.
34
2
3
CABLE IS ATTACHED TO THROTTLE
AND SEALED AT THE FACTORY.
ORDERABLE AS A UNIT ONLY.
PAGE 44 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — STANDARD HANDLE
STANDARD HANDLE
NO.
1
2
PART NO.
20463
20774
20818
20817
0281
20282
0122 C
3615
PART NAME
GRIP, HANDLE RIGHT
COVER, PAD HANDLE
QTY.
1
1
REMARKS
3
DECAL, STD PITCH............................................1...OBSOLETE ON LATER MODELS
4*
5*
6*
7*
8*
9*
10
11
12
13
14
15
16
17
18
19
20
21
WHEEL, HAND J-B HANDLE
BEARING, THRUST, NICE 607
BEARING, TROWEL CONTROL
SCREW, SHS 3/8-16 X 1/2
COLLAR, SET 3/4 ID
SHAFT,TROWEL CONTROL
GRIP, HANDLE LEFT
HANDLE, ADJUSTABLE
THROTTLE, J-B
WHEEL ASSY, HAND
DECAL, CUSTOM 2 1/2 CHROME
SCREW, HHC 3/8-16 X 5.00
SCREW, BHC 1/4- 20 X 3/8 NYL PATCH, NP
SPACER, .360 X 17/64 X 1/8L
SLIDE BLOCK TROWEL CONTROL
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1478
20478
12556
20435
20439
1492
20438
0786
0786 A
20287
20285
20856
1602
CABLE ASSY, LENGTH 1.227m (48.29” )STD FIN.1
SWITCH ASSY, ENGINE-STOP SAFETY .............1.................. SAFETY ITEM
SCREW, RHM 10-24 X 3/8....................................1 ................. COMES WITH #20
.................................................................................................... SWITCH ASSY
22
23
24
25#
26#
27#
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
20988
20514
1662
20275
1118
20279
21017
1493
12567
2942
20434
20845
1116
10133
20392
20471
1261
SCREW, FHSC PHILLIPS 8-32 X 1 1/4
WIRE ASSY, ENGINE-OFF SAFETY SWITCH
TIE, CABLE TY-RAP, BLACK
BLOCK, SUPPORT
PULLEY, SUPPORT BLOCK
PIN, SUPPORT BLOCK 3/8 X 1.59
SCREW, HHC 3/8-16 X 3 1/2 FULL THREAD
SCREW, HHC 3/8-16 X 3 1/4
HANDLE, J/B STD
DECAL, MQ WHITEMAN, 330 mm (13”)
HOUSING, CABLE 1.88 m (74”)
SWIVEL, THROTTLE CABLE
NUT, BRASS JAM 5/16-18
NUT, NYLOC 3/8-16
BRACKET, LIFT TUBE
HANDLE, LIFT ASSY
DECAL, CAUTION, LIFT HANDLE
BLOCK, CABLE ASSY.........................................1.........INCLUDES ITEMS W/ #
HAND WHEEL ASSY, PITCH CONTROL................1.........INCLUDES ITEMS W/ *
HANDLE ASSY, STD FINISHERS..........................1.........CONTACT SALES DEPT.
CABLE, CNTL 5/32 GALV AIRCRFT 1.17m (46")
CLEVIS, BALL END CONTROL CABLE
END-BOLT, CNTL CABLE
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
20280
20819
20299
20301
20421
A8638
1
1
1
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — QUICK-PITCH™ HANDLE
QUICK-PITCH ™T-HANDLE
2
3
25
55
4
20
19
5
14
26
21
1
18
DETAIL “A”
22
58
6
7
3
60
24
10
25
23
SEE
DETAIL “A”
17
SEE
DETAIL
“B”
8
26
27
59
16
28
15
11
9
10
11
50
46
45
ASM
54
12
13
48
30
49
29
ASM
57
31
6
3
32
33
43
40
51
47
2
1
44
34
52
42
41
38
DETAIL “B”
39
56
37
35
36
53
APPLY THREAD LOCK (LOCTITE
242 BLUE OR EQUIVALENT).
1
PART OF ENGINE ASSEMBLY.
2
3
CABLE IS ATTACHED TO THROTTLE
AND SEALED AT THE FACTORY.
ORDERABLE AS A UNIT ONLY.
PAGE 46 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — QUICK-PITCH™ HANDLE
QUICK-PITCH HANDLE
NO.
1
2
3
4
5
6
7
8*
PART NO.
20463
20774
20478
12556
20526
20435
20527
20389
1746
12405
1729
1706
20437
4568
1711
PART NAME
QTY.
REMARKS
GRIP, HANDLE RIGHT
COVER, PAD HANDLE
GRIP, HANDLE LEFT
HANDLE, ADJUSTABLE
1
1
1
1
DECAL, LATCH WARNING .....................................1.................. SAFETY ITEM
THROTTLE, J-B
DECAL, Q.P.WARNING .........................................1.................. SAFETY ITEM
1
HANDLE, QUICK-PITCH
™
1
1
2
3
1
1
1
1
1
1
1
1
1
1
1
1
9*
TRIGGER, QP CHROMED
DECAL, WHITEMAN QUICK-PITCH
PIN, ROLL 3/16 X 1 1/4
SPRING, ENCLOSED QP CLAMP
PIN, QP LATCH
PIN, ROLL 3/16 X 1
SHAFT, CONTROL QP
BUSHING, PIVOT PLATE
WHEEL ASSY, HAND
SCREW, HHC 3/8-16 X 5.00
PIN, ROLL 1/4 X 3/4
ARM, SLIDE CONTROL
CONNECTOR, QP CONTROL ARM
LINKAGE, QP CONTROL
PIN, ROLL 1/4 X 1 3/4
SWITCH ASSY, ENGINE-OFF SAFETY ................1.................. SAFETY ITEM
SCREW, RHM 10-24 X 3/8....................................1...COMES W/ #24 SWITCH ASSY
SCREW, FHSC PHILLIPS 8-32 X 1 1/4
WIRE ASSY, ENGINE-OFF SAFETY SWITCH .....1.................. SAFETY ITEM
CABLE ASSY, QP CONTROL, 1.143 m (45”)
DECAL, MQ WHITEMAN, 330 mm (13”)
SPRING, COUNTER BALANCE
BLOCK, QP ADJUSTMENT
DECAL, PRELOAD TRIM INDICATOR
SCREW, HHC 3/8-16 X 3 1/2 FULL THREAD
TIE, CABLE, TY-RAP BLACK
BLOCK, SUPPORT
PULLEY, SUPPORT BLOCK
PIN, SUPPORT BLOCK 3/8 X 1.59
SCREW, HHC 3/8-16 X 3 1/4
SNAP RING,TRUARC #5100-50
WASHER, 1/2 X 1/32, HARDENED
10*
11
12*
13*
14
15
16
17
18
19+
20+
21+
22+
23+
24
25
26
27
28
29
30
31
32
33
34
35#
36#
37#
38
39
40
™
1719
20439
20438
1731
20443
1709
20269
20276
20856
1602
20988
20514
20297
2942
1715
20270
1735
21017
1662
20275
1118
20279
1493
1737
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1733
CONTINUED NEXT PAGE
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIES TROWEL — QUICK PITCH™ HANDLE
QUICK PITCH HANDLE
NO.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
PART NO.
1736
1718
1732
1717
PART NAME
QTY.
REMARKS
DECAL, ARROW
1
1
1
1
1
1
1
1
NUT, QP TRIM CTRL ADJ
BOLT, STRIPPER 3/8 X 1/2
SCREW, QP TRIM ADJUSTMENT
TUBE, MAIN HANDLE
DECAL, PATENT QP
SWIVEL, ENGINE THROTTLE CABLE
HOUSING, THROTTLE CABLE 1.88 m (74”)
12642
1758
20845
20434
1261
20471
20392
10133
1116
20390
20293
20280
12645
20421
A8638
20271
DECAL, CAUTION, LIFT HANDLE .........................1......... SAFETY ITEM
HANDLE, LIFT ASSY
BRACKET, LIFT TUBE
NUT, NYLOC 3/8-16
1
1
1
2
NUT, BRASS JAM 5/16-18
TRIGGER, QP ASSY .............................................1........INCLUDES ITEMS W/ *
LINKAGE, QP CONTROL ASSY............................1.........INCLUDES ITEMS W/ +
BLOCK, CABLE ASSY..........................................1.........INCLUDES ITEMS W/ #
HANDLE ASSY, MAIN............................................1........CONTACT SALES DEPT.
CLEVIS, BALL END CONTROL CABLE
END-BOLT, CNTRL CABLE
1
1
CABLE, CNTL 5/32 GALV AIRCRFT 1.1m (43.19") 1
PAGE 48 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL —THRUST BEARING KIT ASSY
THRUST BEARING KIT ASSEMBLY.
PAGE 50 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL —THRUST BEARING KIT ASSY
THRUST BEARING KIT ASSEMBLY.
NO.
PART NO. PART NAME
QTY.
REMARKS
1
*
2
*
3
*
4
*
5
*
6
12208
12778
10793
1471
WEAR RING
1
1
1
1
1
1
FLANGE BEARING
THRUST COLLARW/BUSHING
BUSHING
LOWER WEAR PLATE
THRUST BEARING KIT
1154 A
10968
INCLUDES ITEM W/
*
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — 3 AND 4-BLADE SPIDER ASSY
3 AND 4 BLADE SPIDER ASSY
PAGE 52 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — 3 AND 4-BLADE SPIDER ASSY
3 AND 4 BLADE SPIDER ASSY
NO.
PART NO. PART NAME
QTY.
1
1
REMARKS
1
*
2
*
3
*
4
*
12208
12778
10793
1154 A
1157 A
0164 B
1875
WEAR RING
FLANGE BEARING
THRUST COLLAR ............................................................. 1 ........... INCLUDES ITEMS W/#
WEAR PLATE
BEARING INSERT
RADIUS HEAD 3/8- 16 x 1-1/4” ..................................... 3,4 ........... FULLTHREAD
INT. SHKP. WASHER 3/8” 3,4
JAM NUT 3/8- 16 ........................................................... 3,4 ........... CLASS 2B
1
3,4
5
%
6
%
7
%
8%
1876
9
%
0105
0161 C
1156
2827
2828
1163
4164
1316
1161
1322
1456
1167 A
0166 A
1210
1215
1162 A
10968
HHCS 5/16- 18 x 1-1/2”
LOCKWASHER 5/16”
SPIDER PLATE ONLY ...................................................... 1 ........... 3 BLADE ONLY
TROWEL ARM EXTENDED, 16-1/2"
TROWEL ARM 11-3/4
TROWEL ARM LEVER
ROLL PIN 5/16 x 1-3/4”
SPRING (RIGHT HAND)
SPIDER PLATE ONLY ...................................................... 1 ........... 4 BLADE ONLY
RETAINING SCREW ASSY
HEX NUT 3/8-16
6,8
6,8
10
11
12
12
13
14
15
16
17
18
19
20
21
21
22
23
%
%
%
%
%
%
%
%
%
%
%
%
3,4
3,4
3,4
3,4
3,4
1
1
3,4
1
SHSS 3/8-16 x 1-1/2” CONE POINT
LOCK WASHER 3/8”
SPIDER PLATE ASSY (3 BLADE)
SPIDER PLATE ASSY (4 BLADE)
LUBRA- CAP
INCLUDES ITEMS W/
INCLUDES ITEMS W/
%
%
1
3,4
THRUST BEARING KIT .................................................... 1 ........... INCLUDES ITEMS W/
*
24 # 1471
THRUST COLLAR BUSHING
1
*
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — GEARBOX AND ENGINE MOUNTS ASSY
GEARBOX AND ENGINE MOUNTS ASSY
1
2
1
36
12
13
37
35
8
3
39
38
4
5
4
34
6
7
11
9
7
6
14
2
10
15
16
17
18
32
31
30
19
6
X
O
B
G
E
AR
I
20
19
18
QTY. 1
GEARBOX REQUIRES
283 g (22 U.S.OZ.) OF
LUBRICATING OIL
FOR OPERATION.
33
32
GEARBOX ASSEMBLY
40
31
22
GASKET/SEAL KIT
BEARING KIT
41
42
21
23
24
APPLY THREAD LOCK (LOCTITE
242 BLUE OR EQUIVALENT).
5
1
APPLY SEALANT (LOCTITE
572 OR EQUIVALENT).
2
3
.
TORQUE TO 20.3 N m (15 LB/FT.)
25
26
SHIM AS NECESSARY
FOR .127 - .254 mm (0.005 - 0.010in.)
INPUT SHAFT END PLAY.
4
SHIM AS NECESSARY
FOR 0 -.076 mm (0.000 - 0.003)
OUTPUT SHAFT END PLAY.
5
6
29
27
28
USE SPECIALLY FORMULATED
WHITEMAN GEARBOX LUBRICANT
P/N 10139 OR ISO OIL.
3
PAGE 54 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — GEARBOX AND ENGINE MOUNTS ASSY
GEARBOX AND ENGINE MOUNTS ASSY
NO.
1%*
2%
3%
4%*
PART NO.
0753
PART NAME
QTY.
1
4
1
1
1
1
1
1
1
2
2
1
1
1
1
1
3
2
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
4
4
1
1
2
2
1
1
2
REMARKS
SEAL, OIL NATIONAL #470954
SCREW, HHC 1/4-20 X 3/4
FLANGE, INPUT SHAFT
0131 A
12876
20395
20397
20398
20399
20400
20401
20466
20465
0627
1851
12874
1132
0655
0300 B
20476
21033
0121 A
1138
RING, O -139 BUNA N
5%*
SHIM, INPUT 0.002 THICK
SHIM, INPUT 0.003 THICK
SHIM, INPUT 0.005 THICK
SHIM, INPUT 0.010 THICK
SHIM, INPUT 0.020 THICK
BEARING, CUP, TIMKEN #LM11910
BEARING, CONE, TIMKEN #LM11949
KEY, SQUARE 3/16 X 1 1/4
GEAR, WORM & SHAFT ASSY
CASE, GEAR, J, B FINISHER
VENT, AIR
SCREW, HHC 5/16-18 X 3/4
WASHER, FLAT 5/16 SAE
SCREW, HHC 1/4-28 X 3/8
SIGHT GLASS, 3/4 M PIPE STEEL
FITTING, PLUG 3/8 MP SQ HEAD
RING, SNAP, TRUARC 5100-112
BEARING, CUP TIMKEN #M86610
BEARING, CONE TIMKEN #M86647
GEAR, WORM, BRONZE
SHAFT, OUTPUT J/B FIN
KEY, WOODRUFF #21 HARDENED
KEY, WOODRUFF #25
6%#
7%#
8%
9%
10%
11%
12
13
14%
15%
16%
17%
18%# 20475
19%# 20474
20%
21%
22%
23
1140
20470
1139
1238
24%* 20402
SHIM, OUTPUT 0.002 THICK
SHIM, OUTPUT 0.003 THICK
SHIM, OUTPUT 0.005 THICK
SHIM, OUTPUT 0.010 THICK
SHIM, OUTPUT 0.020 THICK
RING, O -257 BUNA N
20403
20404
20405
20406
25%* 20396
26%
27%
28%
12875
10235
1146
COVER, GEARBOX
WASHER, C/S EXT. SHKP
SCREW, FHSC 5/16-18 X 1, NYLOC NP
SEAL, OIL, NATIONAL #470712
ARM, YOKE
RING, SNAP, TRUARC 5100-37 OR EQUIV.
SPACER, .50 OD X .40 ID X 0.25L
PIN, YOKE
29%* 0254
30
31
32
33
34
35
1150
20802
20803
20801
20811
1810
STATIONARY GUARD RING
WEIGHT
CONTINUED NEXT PAGE
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — GEARBOX AND ENGINE MOUNTS ASSY
GEARBOX AND ENGINE MOUNTS ASSY
NO.
36
36
36
37
37
37
37
38
39
40
41
42
PART NO.
1958
1965
20536
1964
20954
20545
20558
1247
PART NAME
QTY.
REMARKS
FRONT ENGINE MOUNT (HONDA)
FRONT ENGINE MOUNT (ROBIN)
FRONT ENGINE MOUNT (BRIGGS)
REAR ENGINE MOUNT (HONDA 8HP)
1
1
1
1
REAR ENGINE MNT.(HONDA W/HAND CLUTCH) 1
REAR ENGINE MOUNT (ROBIN)
REAR ENGINE MOUNT (BRIGGS)
GROMMET 1/4 X .875 ID X 1-5/8 OD
BUSHING, GUARD RING
GEARBOX ASSY.................................................1.........INCLUDES ITEMS W/ %
GASKET/SEAL KIT..............................................1.........INCLUDES ITEMS W/ *
BEARING KIT......................................................1.........INCLUDES ITEMS W/ #
1
1
4
4
1245
20407
21046
21047
PAGE 56 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — ENGINES, HONDA, ROBIN, BRIGGS & STRATTON
ENGINES, 5.96 Kw HONDA, 5.96 Kw ROBIN, & 5.96 Kw HP BRIGGS AND STRATTON
ENGINES, 8 HP HONDA, 8 HP ROBIN, & 8 HP BRIGGS AND STRATTON
PAGE 58 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — ENGINES, HONDA, ROBIN, BRIGGS & STRATTON
ENGINES, 5.96 Kw HONDA, 5.96 Kw ROBIN, & 5.96 Kw HP BRIGGS AND STRATTON
ENGINES, 8 HP HONDA, 8 HP ROBIN, & 8 HP BRIGGS AND STRATTON
NO.
1
1
1
2
PART NO.
1387
20469
1256
0310
PART NAME
QTY.
REMARKS
ENGINE 5.96 kW HONDA
ENGINE 5.96 kW B & S
ENGINE 5.96 kW ROBIN
SQUARE KEY 1/4X1/4X1.1/2"
1
1
1
1
3
0250
AUTOMATIC CLUTCH 1" BORE ..... 1 .......... INCLS. ALL ITEMS W/*
4*
5*
6*
7*
8*
9*
10*
11*
12
13
14
15
16
17
18
19
20
21
0252
0251
0458
0454
0855
0253
0457
0456
0261
1127
1335
0181 B
2577
0300 B
0161 C
10181
1391
SPINDLE 1" BORE
1
1
1
1
1
1
1
1
1
1
CLUTCH HOUSING DRUM
CLUTCH HSNG DRUM BUSHING
WEIGHT SET (INCL 4 WEIGHTS)
SPRING
CLUTCH EXPANSION PLATE
HSSS 3/8-24X1/2"
BELT RUNNER (BEARING)
BELT (A31)(HONDA,B&S)
PULLEY
BELT GUARD .................................. 1 .......... SAFETY ITEM
LOCK WASHER 1/4"
T-BOLT 1/4-20
FLAT WASHER 5/16"
LOCK WASHER 5/16"
HHCS 5/16-24 x 1-1/4"
HHCS 5/16-24 x 1-1/2"
2
2
4
4
4
4
LIFT STRAP ................................... 1 .......... CONTACT UNIT SALES DEPT.
...................................................................... ACCESSORY ITEM
28
0152 1
BELT (A30) GATES (ROBIN)
1
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — MANUAL CLUTCH ASSY CE COMPLIANT OPTION
MANUAL CLUTCH ASSY- CE COMPLIANT OPTION
1
2
13
4
6
5
3
4
10
9
25
24
26
12
7
23
22
21
4
14
20
11
19
1
8
8
16
17
16
18
15
SEE GEARBOX AND ENGINE
MOUNTS ITEM 36 PAGE 52.
1
PAGE 60 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — MANUAL CLUTCH ASSY CE COMPLIANT OPTION
MANUAL CLUTCH ASSY- CE COMPLIANT OPTION
NO.
1
2
3
4
5
6
7
8
PART NO.
1387
PART NAME
ENGINE DR ASSY 5.96kW HONDA1
CLUTCH ASSIST HANDLE ASSY 1
HEX FINISH NUT 5/16-24
FLAT WASHER 5/16”
SCREW, HHC 5/16-24X1.1/4”
SHSS 10-32X1/4”
KEY, CLUTCH 1/4 x 1/4 x 1.1/2"
LOCKWASHER 1/4”
SCREW, HHC 3/8-24 x 1”
HAND CLUTCH CABLE ASSY
SHOULDER BOLT 5/16X1.1/2”
PULLEY,ENGINE
HAND CLUTCH CONTROL LEVER 1 ................. SAFETY ITEM
BELT GUARD MOUNT
BELT GUARD .................................. 1 ................. SAFETY ITEM
QTY.
REMARKS
10036
6014 C
0300 B
10181
10450
0310
0181 B
1672
10936
10971
2469
1
5
1
1
1
4
1
1
1
1
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1512
10831
10833
0730
0262
1127
10229
0161 C
10898
10281
10935
20981
13351
1
HHCS 1/4-20X1”
4
1
1
2
2
1
1
1
1
BELT,(A33)(HONDA)
PULLEY,DRIVEN(HONDA)
HHCS 5/16-24X1”
LOCKWASHER 5/16”
CLUTCH BRKT.
BOLT, SHOULDER 3/8-x 1.1/2”
PULLEY,IDLER
SHOE, BELT HAND CLUTCH
WASHER, FLAT 3/8 USS
........................ EXT THK HI STR
10822 CLUTCH IDLER LEVER
1
1
26
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — GUARD RING ASSY
GUARD RING ASSY
PAGE 62 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — GUARD RING ASSY
GUARD RING ASSY
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
2273
STATIONARY GUARD RING ................................ 1 ......... SAFETY ITEM,
.......................................................................................... REPLACES P/N 1244
SPIDER PLATE ASSY 16-1/2" ARM (EXT) ........ 1 ......... 3-BLADE MODEL
SPIDER PLATE ASSY 16 1/2" ARM (EXT) ........ 1 ......... 4-BLADE MODEL
2
2
1489
1490
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — STABILIZER RING ASSY
STABILIZER RING ASSY
SEE DETAIL “A”
5
DETAIL “A”
4
1
4
3
1
1
2
APPLY LOCTITE 242 BLUE
OR EQUIVALENT.
1
PAGE 64 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — STABILIZER RING ASSY
STABILIZER RING ASSY
NO
1
2
PART NO
0161 C
1237
PART NAME
QTY.
REMARKS
WASHER, LOCK, 5/16 MED
4
SCREW, SCH 5/16-18 X 7/8 ........... 4 .......... NYL, NP
3
1723
ROD END, 5/16-24 MALE
4
4
5
6014 C
1482
NUT, HEX FINISH 5/16-24
RING, STABILIZER, ........................ 1 .......... 368 mm/14-1/2" ARM
8
...................................................................... 3-BLADE MODEL, REPLACES P/N 1234
RING, STABILIZER, ........................ 1 .......... 368 mm/14-1/2" ARM
5
1483
...................................................................... 4-BLADE MODEL, REPLACES P/N 1235
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — BLADES & ADJUSTMENT FIXTURE ASSY
(OPTIONS)
BLADES & ADJUSTMENT FIXTURE ASSY
PAGE 66 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — BLADES & ADJUSTMENT FIXTURE ASSY
BLADES & ADJUSTMENT FIXTURE ASSY
NO.
20
20
21
22
22
23
24
26
27
28
28
29
30
31
32
33
34
35
36
39
39
40
40
41
42
44
46
47
48
49
50
PART NO.
PART NAME
QTY. REMARKS
COMBO FLOAT & FINISH BLADE ........... 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
ENDURO COMBO FLOAT &FINISH BLD . 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
FLOAT BLADE .......................................... 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
FINISH BLADE ......................................... 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
ENDURO FINISH BLADEW/ROTATING ... 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
0202
0201
1434
1162 A
1482
1483
6014 C
1237
0490
0487
0489
0488
HHCS 5/16-18X1" RING
GUARD RING LUG RING
TROWEL LUG (FINISH BLADE ONLY)
LUBRA-CAP
STABILIZER RING 368.3 mm (14.5") ARM 1 ....... (B-3 MODEL)
STABILIZER RING 368.3 mm (14.5") ARM 1 ....... (B-4 MODEL)
HEX NUT 5/16-24
HHCS 5/16-18X7/8" NY-LOC
SHCS 7/16-14X1"
SHCS 3/8-16X1/2"
3,4
3,4
3,4
3,4
6,8
3,4
3
20
1
GRINDING DISC HUB
STONE MOUNT PLATE
1
GRINDING DISC STONE ONLY................ 1 ....... CONTACT UNIT SALES DEPT./ACC. ITEM
GRINDING DISC ASSY ............................ 1 ....... CONTACT UNIT SALES DEPT./ACC. ITEM
UNIVERSAL COMBO BLADE .................. 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
ENDURO UNIVERSAL COMBO BLADE .. 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
UNIVERSAL FINISH BLADE .................... 3,4.... CONTACT UNIT SALES DEPT./ACC. ITEM
ENDURO UNIVERSAL FINISH BLADE .... 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
UNIVERSAL MOUNTING BAR ................. 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
SNAP PIN 1/4"X1.3/4" .............................. 6,8 .... CONTACT UNIT SALES DEPT./ACC. ITEM
0166 A
1723
LOCK WASHER 3/8"
3,4
TROWEL ARM ADJ. FIXTURE ASSY ...... 1 ....... CONTACT UNIT SALES DEPT./ACC. ITEM
REVERSIBLE COMBO BLADE ................ 3,4 .... CONTACT UNIT SALES DEPT./ACC. ITEM
MALE R.H. ROD END 5/16"
FLOAT DISC ............................................. 1 ....... CONTACT UNIT SALES DEPT./ACC. ITEM
FLOAT DISC LATCH PIN .......................... 4 ....... CONTACT UNIT SALES DEPT./ACC. ITEM
1
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — LIFTING BALE ASSY (OPTION)
LIFTING BALE ASSY (OPTION)
PAGE 68 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
BA-SERIESTROWEL — LIFTING BALE ASSY (OPTION)
LIFTING BALE ASSY (OPTION)
NO.
1
PART NO.
PART NAME
QTY.
REMARKS
LIFTING BALE ASSY ..................... 1 .......... SAFETY ITEM
...................................................................... CONTACT UNIT SALES DEPT./ACC. ITEM
2
3
4
10229
0161 C
HHCS 5/16-24X1"
LOCK WASHER 5/16"
LIFTING BALE ASSY ..................... 1 .......... SAFETY ITEM
4
4
...................................................................... CONTACT UNIT SALES DEPT. /ACC. ITEM
5
6
7
8
0205
1394
0166 A
1897
HHCS 3/8-16X1"
FHSCS 3/8-16X1"
LOCK WASHER 3/8"
SPACER (ROBIN ENGINE)
3
1
3
4
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — AIR CLEANER ASSY
AIR CLEANER ASSY
PAGE 70 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — AIR CLEANER ASSY
AIR CLEANER ASSY
NO.
1
2
2
3
3
5
6
8
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
2
1
1
1
2
1
2
REMARKS
16271ZE2000
17210ZE2505
17210ZE2822
17218ZE2505
17218ZE2821
17231ZH9820
17232891000
17238ZE2310
17239ZE1000
17410ZE2020
90203ZA0800
90325044000
90009ZE2003
9405006000
GASKET, ELBOW
ELEMENT, AIR CLEANER, DUAL
ELEMENT, AIR CLEANER, DUAL
FILTER, OUTER
FILTER, OUTER
COVER, AIR CLEANER
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW COMP., AIR CLEANER
WINGNUT 6MM
WINGNUT, TOOL BOX SETTING
BOLT- WASHER 6 X 22
NUT, FLANGE 6MM
9
10
12
13
14
15
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CAMSHAFT ASSY
CAMSHAFT ASSY
PAGE 72 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CAMSHAFT ASSY
CAMSHAFT ASSY
NO.
1
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NO.
PART NAME
QTY.
1
1
1
2
2
2
2
1
1
1
2
1
1
1
1
2
REMARKS
14100ZE2W00
14100ZE2W01
14100ZE2306
14410ZE2013
14431ZE2010
14441ZE2000
14451ZE1013
14568ZE1000
14711ZE2000
14721ZE2000
14751ZE2003
14771ZE2000
14773ZE2000
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
CAMSHAFT ASSY
CAMSHAFT ASSY
CAMSHAFT
ROD PUSH
ARM VALVE ROCKER
LIFTER VALVE
PIVOT ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN.
VALVE, EX.
SPRING, VALVE
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR,VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
NUT, PIVOT ADJ.
2
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CARBURETOR ASSY
CARBURETOR ASSY
PAGE 74 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CARBURETOR ASSY
CARBURETOR ASSY
NO.
1
2
3
4
4
5
6
7
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
REMARKS
16010ZE2812
16011ZA0931
16013ZA0931
16015ZE2005
16015ZE8005
16016ZHW01
16024ZE1811
16028ZE0005
16028ZE2005
16100ZE2W71
16124ZE0005
16166ZE2W70
16172ZE3W10
16173001004
16211ZE2000
16220ZA0702
16221ZA0800
16223ZA0800
16610ZE1000
16953ZE1406
16953ZE1811
16953ZE1812
16954ZE1811
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
93500030080G
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
CHAMBER SET, FLOAT
CHAMBER SET, FLOAT
SCREW SET
SCREW SET, DRAIN
SCREW SET B
8
9
CHOKE SET
CARBURETOR ASSY
SCREW, THROTTLE STOP
NOZZLE, MAIN
COLLAR, SET
O-RING
INSULATOR, CARBURETOR
SPACER COMP., CARBURETOR
GASKET, CARBURETOR
GASKET, INSULATOR
LEVER COMP., CHOKE, STD.
LEVER, VALVE
10
11
12
13
14
15
16
17
18
19
19
19
20
20
21
22
23
24
24
25
26
26
26
27
28
LEVER, VALVE
LEVER, VALVE
PLATE, LEVER SETTING
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN 3 X 6
SCREW, PAN 3 X 8
PIN, SPRING 2 X 12
JET, MAIN #82, OPTIONAL
JET, MAIN #85, OPTIONAL
JET, MAIN #88
99101ZH80820
99101ZH80850
99101ZH80880
99204ZE20400
16015ZE8005
JET SET, PILOT #40
CHAMBER SET, FLOAT
1
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CONTROL ASSY
CONTROL ASSY
PAGE 76 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CONTROL ASSY
CONTROL ASSY
NO.
2
3
4
5
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
REMARKS
16551ZE2000
16555ZE2000
16561ZE2000
16562ZE2000
16570ZE2W20
16571ZE2W00
16574ZE1000
16575ZE2W00
16576891000
16578ZE1000
16581ZE2W00
16584883300
16592883310
90013883000
90015ZE5010
90114SA0000
93500050280A
93500050160A
9405006000
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
CONTROL ASSY, REMOTE
LEVER, CONTROL
SPRING, LEVER
WASHER, CONTROL LEVER
8
10
11
12
13
14
15
16
17
19
20
21
24
26
27
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE COMP., CONTROL
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
BOLT, FLANGE 6 X 12 CT200
BOLT, GOVERNOR ARM
NUT, SELF-LOCK 6MM
SCREW, PAN 5 X 28
1
1
1
SCREW, PAN 5 X 16
NUT, FLANGE 6MM
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CRANKCASE COVER ASSY
CRANKCASE COVER ASSY
PAGE 78 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CRANKCASE COVER ASSY
CRANKCASE COVER ASSY
NO.
2
3
3
4
5
5
6
7
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
REMARKS
11400ZE2601
11381ZE2800
11381ZE2801
15600ZG4003
15600735003
156000735700
15620ZG4910
15621896010
15625ZE1000
15625ZE1003
16510ZE2811
16511ZE2000
16512ZE2811
16513ZE2000
16531ZE2000
90473147000
90602ZE1000
90701HC4000
91201890003
9410106800
COVER ASSY, CRANKCASE
GASKET, CASE COVER
GASKET, CASE COVER
CAP ASSY, OIL FILLER
CAP ASSY, OIL FILLER
CAP ASSY, OIL FILLER
CAP, OIL FILLER
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
GOVERNOR ASSY, BALANCER
WEIGHT, GOVERNOR
HOLDER, GOVERNOR WEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
WASHER 6 X 16
CLIP, GOVERNOR HOLDER
PIN, DOWEL 8 X 12
OIL SEAL 30 X 46 X 8
WASHER, PLAIN 6MM
BOLT, FLANGE 8 X 35
BEARING, RADIAL BALL 6202
BEARING, RADIAL BALL 6206
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1
2
1
1
7
1
957010803500
961006202000
961006206000
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CRANKSHAFT ASSY
CRANKSHAFT ASSY
PAGE 80 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CRANKSHAFT ASSY
CRANKSHAFT ASSY
NO.
2
8
10
12
PART NO.
PART NAME
QTY.
REMARKS
13320ZE2601
13351ZE2010
90745ZE2600
961006206000
CRANKSHAFT COMP., Q- TYPE
WEIGHT, BALANCER
KEY 6.3 X 6.3 X 43
1
1
1
1
BEARING, RADIAL BALL 6206
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CYLINDER BARREL ASSY
CYLINDER BARREL ASSY
PAGE 82 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CYLINDER BARREL ASSY
CYLINDER BARREL ASSY
NO.
1
2
2
2
3
3
4
5
6
7
8
9
10
11
12
12
13
14
15
16
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
REMARKS
12000ZE2834
15510ZE2023
15510ZE2033
15510ZE2043
16541ZE2000
16541ZE2010
32197ZE2003
90013883000
90131896650
90446KE1000
91201890003
91353671003
9405010000
9410912000
9425108000
9425110000
957010601200
961006202000
90013883000
34150ZH7003
CYLINDER ASSY, BALANCER + OIL ALERT
SWITCH ASSY, OIL LEVEL
SWITCH ASSY, OIL LEVEL
SWITCH ASSY, OIL LEVEL
SHAFT, GOVERNOR ARM
SHAFT, GOVERNOR ARM
SUB- HARNESS
BOLT, FLANGE 6 X12 CT200
BOLT, DRAIN PLUG
WASHER 8.2 X17X0.8
OIL SEAL 30X46X8
O-RING 14MM ARAI
NUT FLANGE 10MM
WASHER, DRAIN PLUG 12MM
PIN, LOCK 8MM
PIN, LOCK 10MM
BOLT, FLANGE 6X12
2
1
1
1
BEARING, RADIAL BALL 6202
BOLT, FLANGE 6X12 CT200
ALERT UNIT, OIL
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CYLINDER HEAD ASSY
CYLINDER HEAD ASSY
PAGE 84 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — CYLINDER HEAD ASSY
CYLINDER HEAD ASSY
NO.
1
2
3
4
5
6
7
8
10
11
12
12
13
14
15
16
17
17
17
17
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
2
2
2
1
2
1
4
REMARKS
12200ZH9000
12204ZE2306
12205ZE2305
12216ZE2300
12251ZE2800
12310ZE2020
12391ZE2020
14775ZE2010
90014ZE2000
90042ZE2000
90047ZE2000
92900080320E
90441ZE2010
9430112200
CYLINDER HEAD COMP.
GUIDE, VALVE, OS, OPTIONAL
GUIDE, EX. VALVE, OS, OPTIONAL
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER COMP., HEAD
GASKET, CYLINDER HEAD COVER
SEAT, VALVE SPRING
BOLT, HEAD COVER
BOLT, STUD 8X123
BOLT, STUD 8X47
BOLT 2, STUD 8X32
WASHER COMP., HEAD COVER
PIN A, DOWEL 12X20
BULK HOSE, VACUUM 11X1000, 11X100
BOLT, FLANGE 10X80
950051100130M
957011008000
9807955846
9807955855
9807956846
SPARK PLUG, BPR5ES, NGK
SPARK PLUG, W16EPR-U, DENSO, OPTIONAL
SPARK PLUG, BPR6ES, NGK
SPARK PLUG, W20EPR-U, DENSO
1
1
1
1
9807956855
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — FAN COVER ASSY
FAN COVER ASSY
PAGE 86 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — FAN COVER ASSY
FAN COVER ASSY
NO.
1
2
2
3
4
5
5
7
PART NO.
PART NAME
QTY.
REMARKS
16731ZE2003
19610ZE2010ZA
19610ZE2010ZC
19631ZE2D00
32197ZH8003
36100ZE1015
36100ZH7003
90013883000
90684ZA0601
CLIP, TUBE
1
1
1
1
1
1
1
6
1
COVER COMP., FAN *R8* BRIGHT RED
COVER COMP., FAN *NH1* BLACK
SHROUD
SUB-HARNESS
SWITCH ASSY, ENGINE STOP
SWITCH ASSY, ENGINE STOP
BOLT, FLANGE 6X12, CT200
CLIP, WIRE HARNESS
9
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — FLYWHEEL ASSY
FLYWHEEL ASSY
PAGE 88 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — FLYWHEEL ASSY
FLYWHEEL ASSY
NO.
1
2
4
7
PART NO.
PART NAME
QTY.
REMARKS
19511ZE2000
28450ZE2W11
31100ZE2010
90201ZE3V00
90741ZE2000
FAN, COOLING
1
1
1
1
1
PULLEY COMP., STARTER, SCREEN GRID
FLYWHEEL COMP.
NUT, SPECIAL 16MM
KEY, SPECIAL WOODRUFF 25X18
8
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — FUELTANK ASSY
FUEL TANK ASSY
PAGE 90 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — FUELTANK ASSY
FUEL TANK ASSY
NO.
1
2
3
3
4
5
6
7
PART NO.
PART NAME
RUBBER SUPPORTER 107MM
JOINT, FUEL TANK
TANK COMP., FUEL *NH31*, MCKINLEY WHITE
TANK COMP., FUEL *NH1*, BLACK
CAP COMP., FUEL FILLER
CAP COMP., FUEL FILLER
GASKET, FUEL FILLER CAP
GASKET, FUEL FILLER CAP
FILTER, FUEL
FILTER, FUEL
HOLDER, FUEL FILTER
O-RING 14MM, ARAI
NUT, FLANGE 8MM
BULK HOSE, FUEL 4.5X3000, 4.5X222
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
2
REMARKS
16854ZH8000
16955ZE1000
17510ZE2010ZA
17510ZE2020ZD
17620ZE2W00
17620ZH7023
17631ZH7003
17631329003
17672ZE2W01
17672880000
17673893000
91353671003
9405008000
8
9
10
11
12
13
14
15
950014500360M
9500202080
957010802500
CLIP, TUBE, B8
BOLT, FLANGE 8X25
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
PAGE 92 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — GASKET KIT
GASKET KIT ASSY
NO.
PART NO.
PART NAME
QTY.
REMARKS
06111ZE2408
11381ZE2800
11381ZE2801
12251ZE2800
12391ZE2020
16221ZA0800
16223ZA0800
18333ZE3800
18333ZK6Y00
GASKET KIT
1
1
1
1
1
1
1
1
1
1
1
2
3
4
5
6
6
GASKET, CASE COVER
GASKET, CASE COVER
GASKET, CYLINDER HEAD
GASKET, CYLINDER HEAD COVER
GASKET, CARBURETOR
GASKET, INSULATOR
GASKET, EX. PIPE
GASKET, EX. PIPE, WACKER
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 93
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — IGNITION COIL ASSY
IGNITION COIL ASSY
PAGE 94 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — IGNITION COIL ASSY
IGNITION COIL ASSY
NO.
1
2
6
8
PART NO.
PART NAME
QTY.
REMARKS
30500ZE2023
30700ZE1013
31512ZE2000
36101ZE1010
90015883000
COIL ASSY, IGNITION
CAP ASSY, NOISE SUPPRESSOR
GROMMET, WIRE
1
1
1
1
2
WIRE, STOP SWITCH 370MM
BOLT, FLANGE 6X28
11
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 95
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — MUFFLER ASSY
MUFFLER ASSY
PAGE 96 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — MUFFLER ASSY
MUFFLER ASSY
NO.
1
2
3
4
5
6
6
7
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
1
6
3
1
5
REMARKS
18310ZE2W00
18320ZE2W01
18323ZE2W00
18330ZE2W00
18331ZE2810
18333ZE3800
18333ZK6Y00
18355ZE2010
18381ZE2W10
90013883000
90050ZE1000
90055ZE1000
90050ZE1000
9405008000
MUFFLER COMP.
PROTECTOR COMP., MUFFLER
PROTECTOR, EX. PIPE
PIPE, EX.
CAP, MUFFLER
GASKET, EX. PIPE
GASKET, EX. PIPE, WACKER
ARRESTER, SPARK
GASKET, MUFFLER, ARRESTER
BOLT, FLANGE 6X12 CT200
SCREW, TAPPING 5X8
SCREW, TAPPING 4X6
SCREW, TAPPING 5X8
NUT, FLANGE 8MM
8
10
11
12
13
14
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 97
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — PISTON ASSY
PISTON ASSY
PAGE 98 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — PISTON ASSY
PISTON ASSY
NO.
1
1
1
1
1
2
2
2
2
3
4
4
5
6
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
2
2
REMARKS
13010ZE2013
13011ZE2013
13011ZE2014
13012ZE2013
13013ZE2013
13101ZE2W00
13102ZE2W00
13103ZE2W00
13104ZE2W00
13111ZE2000
13200ZE2000
13200ZE2305
90001ZE8000
90551ZE1000
RING SET, PISTON, STD.
RING SET, PISTON, OS 0.25, OPTIONAL
RING SET, PISTON, OS 0.25, OPTIONAL
RING SET, PISTON, OS 0.50, OPTIONAL
RING SET, PISTON, 0.75, OPTIONAL
PISTON, STANDARD
PISTON, OS 0.25, OPTIONAL
PISTON, OS 0.50, OPTIONAL
PISTON, 0.75, OPTIONAL
PIN, PISTON
ROD ASSY, CONNECTING STANDARD
ROD ASSY, CONNECTING, US 0.25, OPT.
BOLT, CONNECTING ROD
CLIP, PISTON PIN 18MM
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 99
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — RECOIL STARTER ASSY
RECOIL STARTER ASSY
PAGE 100 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — RECOIL STARTER ASSY
RECOIL STARTER ASSY
NO.
1
1
2
2
3
4
5
6
7
8
10
11
PART NO.
PART NAME
QTY.
REMARKS
28400ZE2W01ZA
28400ZE2W01ZB
28410ZE2W01ZA
28410ZE2W01ZB
28421ZE2W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28461ZE2W02
28462ZE2W01
STARTER ASSY, RECOIL *R8* BRIGHT RED
STARTER ASSY, RECOIL *NH1*, BLACK
CASE COMP., RECOIL STARTER *R8* BRT. RED
CASE COMP., RECOIL STARTER *NH1*, BLACK
PULLEY, RECOIL STARTER
RATCHET, STARTER
1
1
1
1
1
2
1
1
2
1
1
1
SPRING, FRICTION
SPRING, STARTER RETURN
SPRING RATCHET
RETAINER, SPRING
GRIP, STARTER
ROPE, RECOIL STARTER , NA USE ALT:08550-
ZG921-11
11
12
13
14
28462ZE2W11
28469ZE2W01
90004ZE2W01
90008ZE2003
ROPE, RECOIL STARTER
GRIP, REINFORCEMENT
SCREW, CENTER
1
1
1
3
BOLT, FLANGE 6X10
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 101
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE —TOOLS
TOOLS ASSY
PAGE 102 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE —TOOLS
TOOLS ASSY
NO.
4
PART NO.
89218ZE1000
PART NAME
WRENCH COMP., SPARK PLUG
QTY.
1
REMARKS
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 103
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — LABELS
LABELS ASSY
PAGE 104 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX-240K1 ENGINE — LABELS
LABELS ASSY
NO.
1
2
3
5
8
8
15
16
PART NO.
PART NAME
QTY.
REMARKS
87521ZE2W01
87522ZE1810
87522ZH9000
87528ZE2810
87532ZB4G60
87532ZB4H50
87586ZH7W00
87532ZH8810
EMBLEM, INTERNAL
1
1
1
1
1
1
1
1
MARK, CAUTION, EXTERNAL
LABEL, CAUTION
MARK, CHOKE, EXTERNAL
MARK, OIL ALERT, GERMAN
MARK, OIL ALERT, FRENCH
LABEL, FUEL CAUTION
MARK, OIL ALERT, E
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 105
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — CRANKCASE ASSY
CRANKCASE ASSY
PAGE 106 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — CRANKCASE ASSY
CRANKCASE ASSY
NO.
PART NO.
PART NAME
QTY.
REMARKS
10
2541010131
2541010231
13212AA080
0440300030
0600300020
0600150010
0310060020
1425560103
0105080290
0401140030
0211140020
2541100301
0440300030
0600300020
0600150010
1600280010
2344500101
2054190103
2276360107
2276360107
0213160020
0213160020
2541600103
0011308300
2541750213
0043505100
2701300101
2541500113
0110100040
2701550303
2701600403
0310060020
0110060020
2541430101
2541440111
2461600603
2461600713
0851080000
0851080000
2549900107
CRANKCASE CP
1
CRANKCASE CP ........................................1.................. ELECTRIC START TYPE
VALVE GUIDE ............................................2.................. STANDARD
OIL SEAL ....................................................1.................. 30 X 45 X 8
BALL BEARING ..........................................1.................. BB-6206C3 060-03002-20
BALL BEARING ..........................................1.................. BB-6202C3
20
30
40
45
50
55
60
80
DOWEL PIN
2
PIPE .......................................................... 2................... ELECTRIC START TYPE
STUD
PLUG
GASKET
2
2
2
90
210
220
230
235
MAIN BEARING COVER CP ..................... 1................... METRIC
OIL SEAL ................................................... 1................... 30 X45 X 8
BALL BEARING ......................................... 1................... BB-6206C3 060-03002-20
BALL BEARING ......................................... 1................... D,DS TYPE BB-6202C3
BALL BEARING ......................................... 1................... BB-62/28C3
GOVERNOR GEAR CP
GOVERNOR SLEEVE
OIL GAUGE ASSY
OIL GAUGE ASSY..................................... 1................... W/OIL SENSOR
GASKET
GASKET .................................................... 1................... W/OIL SENSOR
GASKET, BEARING COVER
BOLT AND WASHER ASSY
OIL SHELTER (SENSOR) .......................... 1................... W/OIL SENSOR
SCREW AND WASHER ASSY .................. 3................... W/OIL SENSOR
CYLINDER HEAD CP
GASKET, HEAD
FLANGE BOLT
ROCKER COVER
GASKET, ROCKER COVER
DOWEL PIN
FLANGE BOLT
BREATHER COVER CP
BREATHER PLATE CP
GASKET, BREATHER COVER
GASKET, BREATHER PLATE
RUBBER PIPE ........................................... 1................... 8 X11 X 60
RUBBER PIPE ........................................... 1................... CYCLONE TYPE 8 X 11 X 75
GASKET SET
250
260
270
1
1
2
-280
2
290
300
330
340
610
620
630
680
690
700
710
810
820
830
840
850
1
8
1
1
4
1
1
2
6
1
1
1
1
960
1
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 107
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — CRANKSHAFT ASSY
CRANKSHAFT ASSY
PAGE 108 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — CRANKSHAFT ASSY
CRANKSHAFT ASSY
NO.
PART NO.
PART NAME
QTY.
REMARKS
10
2542090101
2542100101
2542120101
2542020101
2542030101
2542070101
0230300170
0230300180
0230300190
0021808000
0032018000
0323030010
2542410103
2542250100
2462300103
2702330103
2702340103
2702340203
2702340303
2542350107
2542350207
2542350307
0565180010
CRANKSHAFT CP ..................................... 1................... SAE 1” KEYED SHAFT
CRANKSHAFT CP ..................................... 1................... SAE PUMP SHAFT
CRANKSHAFT CP ..................................... 1................... SAE TAPER SHAFT
CRANKSHAFT CP ..................................... 1................... METRIC DS TYPE
CRANKSHAFT CP ..................................... 1................... METRIC PUMP TYPE
CRANKSHAFT CP ..................................... 1................... METRIC GENERATOR TYPE
SPACER T=0.6........................................... 1................... SELECT 1 SPACER ONLY
SPACER T=0.8........................................... 1................... SELECT 1 SPACER ONLY
SPACER T=1.0........................................... 1................... SELECT 1 SPACER ONLY
40
50
60
70
210
310
320
350
360
NUT
1
1
1
1
1
2
1
SPRING WASHER
WOODRUFF KEY
BALANCER SHAFT
CONNECTING ROD ASSY
CONNECTING ROD BOLT
PISTON PIN
PISTON ..................................................... 1 ................... STANDARD
PISTON ..................................................... 1 ................... OVERSIZE 0.25 MM
PISTON ..................................................... 1 ................... OVERSIZE 0.50 MM
PISTON RING SET ................................... 1 ................... STANDARD
PISTON RING SET ................................... 1 ................... OVERSIZE 0.25 MM
PISTON RING SET ................................... 1 ................... OVERSIZE 0.50 MM
370
380
CLIP
2
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 109
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — INTAKE AND EXHAUST ASSY
INTAKE AND EXHAUST ASSY
PAGE 110 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — INTAKE AND EXHAUST ASSY
INTAKE AND EXHAUST ASSY
NO.
10
35
36
37
50
60
70
80
PART NO.
PART NAME
QTY.
1
1
1
1
2
2
2
1
1
4
2
2
2
2
1
1
1
1
2
4
1
1
1
1
REMARKS
2543170141
2543640113
0051904100
0031522000
2393330113
2463361103
2463371103
2703340103
2703350103
2463550103
2703530103
26136001A3
2693580103
0170060090
2703650103
2703010101
2543420111
2463520103
0170080030
0152006090
0152060100
0011008160
2703480103
2463700107
0150040060
2543300101
0105060191
2543261310
2343600308
2073269008
2703260100
2343600308
2703265008
2703261008
2343260407
2343290103
2463600113
0011308280
2343590203
2263921200
0023806000
0011006120
2304390101
CAMSHAFT CP
RELEASE LEVER
SPRING PIN
SNAP RING
TAPPET
VALVE SPRING
SPRING RETAINER
INTAKE VALVE
EXHAUST VALVE
COLLET VALVE
PUSH ROD
ROCKER ARM
BOLT, PIVOT
NUT
90
95
210
220
230
240
260
310
320
340
350
360
363
365
430
440
445
500
505
510
-2
GUIDE PLATE
MUFFLER CP
MUFFLER COVER
GASKET, MUFFLER
NUT
TAPPING BOLT
TAPPING BOLT
BOLT AND WASHER ASSY
EXHAUST PIPE COVER
DEFLECTOR ASSY
TAPPING SCREW
INTAKE PIPE CP
STUD
AIR CLEANER ASSY ................................ 1................... CYCLONE, TOP INLET TYPE
PACKING ................................................... 1................... CYCLONE, TOP INLET TYPE
GROMMET ................................................ 1................... CYCLONE, TOP INLET TYPE
AIR CLEANER ASSY ................................ 1................... FOAM AIR CLEANER TYPE
PACKING ................................................... 1................... FOAM AIR CLEANER TYPE
PLATE ........................................................ 1................... FOAM AIR CLEANER TYPE
CLEANER ELEMENT ................................ 1................... FOAM AIR CLEANER TYPE
ELEMENT SET .......................................... 1................... CYCLONE TYPE
3
1
2
-3
510
-2
-13
-520
520
540
555
556
560
570
INSULATOR
1
1
3
2
GASKET, INTAKE PIPE
BOLT AND WASHER ASSY
GASKET 2, INSULATOR
NUT AND WASHER ASSY ........................ 2................... CYCLONE, TOP INLET TYPE
FLANGE NUT............................................. 2................... FOAM AIR CLEANER TYPE
BOLT AND WASHER ASSY ...................... 2................... CYCLONE, TOP INLET TYPE
CHOKE KNOB ........................................... 1................... CYCLONE, TOP INLET TYPE
580
650
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 111
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — GOVERNOR ASSY
GOVERNOR ASSY
PAGE 112 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — GOVERNOR ASSY
GOVERNOR ASSY
NO.
10
20
30
40
50
60
70
80
PART NO.
PART NAME
QTY.
REMARKS
2544230123
2464220123
2544270101
2544280103
0031306000
0011406300
0186060020
2544250113
2704330200
2704330100
2704330201
2704330101
2274360103
2704350103
0043104250
2694550303
2274500203
0043106300
0022706000
0110060050
0110060030
2544420123
0043104080
0022706000
GOVERNOR LEVER
GOVERNOR SHAFT
GOVERNOR ROD CP
ROD SPRING
1
1
1
1
2
1
1
1
CLIP
BOLT AND WASHER ASSY
NUT
GOVERNOR SPRING
SPEED CONTROL ASSY ..................... 1 ............. MANUAL W/REMOTE CABLE OPT.
SPEED CONTROL ASSY ..................... 1 ............. MANUAL ONLY CONTROL
SPEED CONTROL CP.......................... 1 ............. MANUAL W/REMOTE CABLE OPT.
SPEED CONTROL................................ 1 ............. MANUAL ONLY CONTROL
KNOB
STOP PLATE
SCREW
IDLE SET SPRING
SPRING WASHER
SCREW
310
320
330
340
345
346
350
360
370
380
1
1
1
1
1
1
1
NUT
FLANGE-BOLT...................................... 1 ............. MANUAL W/REMOTE CABLE OPT.
FLANGE BOLT...................................... 1 ............. MANUAL ONLY CONTROL
WIRE BRACKET................................... 1 ............. MANUAL W/REMOTE CABLE OPT.
SCREW ................................................. 1 ............. MANUAL W/REMOTE CABLE OPT.
NUT ....................................................... 1 ............. MANUAL W/REMOTE CABLE OPT.
410
440
450
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 113
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — COOLING AND STARTING ASSY
COOLING AND STARTING ASSY
PAGE 114 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — COOLING AND STARTING ASSY
COOLING AND STARTING ASSY
NO.
PART NO.
PART NAME
QTY.
REMARKS
10
2545345001
2545355011
2709170303
0110060020
0732004950
2545270103
2705020100
2705011508
2705012008
2705011008
2615010008
2705012508
2275013108
2705014508
2705026108
2275015208
0110060010
BLOWER HOUSING CP ....................... 1 ............. BLACK
BLOWER HOUSING CP ....................... 1 ............. BLACK, ELECTRIC START TYPE
LABEL, TRADE MARK ......................... 1 ............. ROBIN/SUBARU
FLANGE BOLT
LABEL, RECOIL OHV
HEAD COVER
RECOIL STARTER ASSY ..................... 1 ............. D TYPE
SPIRAL SPRING
REEL
STARTER ROPE
STARTER KNOB
RATCHET
FRICTION SPRING
STARTER PULLEY
RATCHET GUIDE.................................. 1 ............. D TYPE
SET SCREW
FLANGE BOLT
20
40
45
90
210
-1
-2
-3
-4
-5
5
1
1
1
1
1
1
2
1
1
-6
-11
-35
-49
220
1
4
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 115
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — FUELTANK ASSY
FUEL TANK ASSY
PAGE 116 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — FUELTANK ASSY
FUEL TANK ASSY
NO.
10
20
30
40
50
-1
-2
-3
-4
-8
-15
70
80
90
105
PART NO.
PART NAME
QTY.
REMARKS
2546105011
0732003900
0430430015
0641360010
0642008600
0642004110
0642001430
0642001410
0642002360
0642002790
0642003230
2346260101
0851060000
0561110020
0011308200
FUEL TANK CP ..................................... 1 ............. BLACK
LABEL, CAUTION
FUEL TANK CAP CP
FUEL FILTER CP
FUEL STRAINER ASSY
FILTER
RUBBER PACKING
CLIP
LOCK NUT
1
1
1
1
1
1
1
1
1
1
1
LOCK BOLT
SPRING
FUEL PIPE CP
RUBBER PIPE ...................................... 1 ............. 6 X 12 X 75
HOSE CLAMP
BOLT AND WASHER ASSY
2
4
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 117
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — CARBURETOR ASSY
CARBURETOR ASSY
PAGE 118 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — CARBURETOR ASSY
CARBURETOR ASSY
NO.
PART NO.
PART NAME
QTY.
REMARKS
210
2546252300
2546256010
2396253508
2096235108
2546252508
2376245108
2546242008
2466243608
2306244808
2346252108
2346252008
2396256008
2346255008
2546253108
2546253008
2246254408
2266255008
2246231208
2146251508
2246255208
2076234508
2066254008
2346250608
2546244008
2546240308
2546240208
2466245508
2246256918
2266270118
1066239208
2466243508
2306244608
2476255008
2366268008
2466242508
1566235108
2466255108
CARBURETOR ASSY ........................... 1 ............. CYCLONE, TOP INLET TYPE
CARBURETOR ASSY ........................... 1 ............. FOAM AIR CLEANER TYPE
-1
-2
-3
-4
-5
-6
-7
-8
THROTTLE VALVE
SCREW
VALVE, CHOKE
SCREW, PANHEAD
PILOT JET
ADJUSTER
SPRING
1
2
1
2
1
1
1
CHOKE LEVER ASSY.......................... 1 ............. CYCLONE, TOP INLET TYPE
CHOKE LEVER ASSY.......................... 1 ............. FOAM AIR CLEANER TYPE
RING ..................................................... 1 ............. CYCLONE, TOP INLET TYPE
RING ..................................................... 1 ............. FOAM AIR CLEANER TYPE
SHAFT ASSY, THROTTLE.................... 1 ............. CYCLONE, TOP INLET TYPE
SHAFT ASSY, THROTTLE.................... 1 ............. FOAM AIR CLENAER TYPE
-9
-11
-12
-13
-14
-15
-16
-17
-18
-19
-20
-22
BOLT
RING
1
1
1
1
NEEDLE VALVE ASSY
FLOAT PIN
FLOAT CHAMBER BODY1
INSERT WASHER
PACKING, CHAMBER
FLOAT ASSY
1
1
1
1
MAIN NOZZLE
MAIN JET ............................................. 1 ............. CYCLONE, TOP INLET TYPE
MAIN JET ............................................. 1 ............. FOAM AIR CLEANER TYPE
BOLT ..................................................... 1 ............. CYCLONE,TOP INLET TYPE
CLIP ...................................................... 1 ............. CYCLONE, TOP INLET TYPE
CLIP ...................................................... 1 ............. FOAM AIR CLEANER TYPE
SEAL..................................................... 1 ............. CYCLONE, TOP INLET TYPE
-23
-24
-32
-40
-41
-61
-62
-89
-101
-121
ADJUST SCREW
SPRING
1
1
CAP....................................................... 1 ............. CYCLONE, TOP INLET TYPE
SEAL..................................................... 1 ............. CYCLONE, TOP INLET TYPE
GUIDE HOLDER
PACKING .............................................. 1 ............. CYCLONE, TOP INLET TYPE
CAP
1
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 119
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — RECOIL START ASSY
RECOIL START ASSY
PAGE 120 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — RECOIL START ASSY
RECOIL START ASSY
NO.
10
11
30
60
70
90
PART NO.
PART NAME
QTY.
REMARKS
2347020111
2547943021
0011406250
0660000361
0150040090
0566000190
0566120050
0650140031
0650140150
0650141030
RL86C
FLYWHEEL CP
IGNITION COIL CP
BOLT AND WASHER ASSY
SWITCH ASSY
TAPPING SCREW
CLAMP
1
1
2
1
2
1
CLAMP.................................................. 1 ............. W/OIL SENSOR
SPARK PLUG........................................ 1 ............. NGK B-6HS
SPARK PLUG........................................ 1 ............. EXPORT (CE) NGK (BR-6HS)
SPARK PLUG........................................ 1 ............. CHAMPION (L86C)
SPARK PLUG........................................ 1 ............. EXPORT (CE) CHAMPION
100
110
0655000051
SPARK PLUG CAP
1
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 121
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — OIL SENSOR ASSY
OIL SENSOR ASSY
PAGE 122 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH25-2 ENGINE — OIL SENSOR ASSY
OIL SENSOR ASSY
NO.
700
760
790
PART NO.
PART NAME
QTY.
REMARKS
KS31102801
2147312201
2147900301
OIL SENSOR CP 19 ............................. 1 ............. W/OIL SENSOR
WIRE 22 CP .......................................... 1 ............. W/OIL SENSOR
CLAMP CP............................................ 1 ............. W/OIL SENSOR
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 123
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Parts must be in new and resalable PRICINGANDREBATES
condition,intheoriginalMultiquippackage
(ifany),andwithMuiltiquippartnumbers
clearlymarked.
Terms of payment for parts are net 10 days.
FREIGHTPOLICY
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspecific
dateandallordersreceivedonorafterthatdate
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
willbebilledattherevisedprice. Rebatesfor
price declines and added charges for price
increaseswillnotbemadeforstockonhandat
thetimeofanypricechange.
a. Obsolete parts. (If an item is in the
pricebookandshowsasbeingre-
placedbyanotheritem,itisobsolete.)
Multiquip reserves the right to quote and sell
directtoGovernmentagencies,andtoOriginal
EquipmentManufacturer(OEM)accountswho
useourproductsasintegralpartsoftheirown
products.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
andotherrubberparts)thatwere
purchasedmorethansixmonths
priortothereturndate.
MINIMUMORDER
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
SPECIALEXPEDITINGSERVICE
c. Anylineitemwithanextendeddealer
netpriceoflessthan$5.00.
A$35.00surchargewillbeaddedtotheinvoice
forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
Returnshipmentswillbeacceptedandcredit
will be allowed, subject to the following
provisions:
f.
Paint,chemicals,andlubricants.
LIMITATIONSOFSELLER’SLIABILITY
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
itemwithrespecttowhichdamagesareclaimed,
andinnoeventshallMultiquipbeliableforloss
of profit or good will or for any other special,
consequentialorincidentaldamages.
1. AReturnedMaterialAuthorization(RMA)
must be approved by Multiquip prior to
shipment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Sales that defines item numbers,
quantities,anddescriptionsoftheitemsto
bereturned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returnedtothesenderathisexpense.
LIMITATIONOFWARRANTIES
Nowarranties,expressedorimplied,aremade
in connection with the sale of parts or trade
accessories nor as to any engine not
manufacturedbyMultiquip.Suchwarranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it any
other obligation or liability whatever in
connectionwiththesaleofitsproducts.Apart
fromsuchwrittenstatementofwarranty,there
are no warranties, expressed, implied or
statutory,whichextendbeyondthedescription
oftheproductsonthefacehereof.
a. Thepartsnumbersanddescriptions
mustmatchthecurrentpartsprice
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. Thelistmuststatethereason(s)for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhich
theitemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. Thelistmustincludethenameand
phonenumberoftheperson
requestingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspecific
dateandallordersreceivedonorafterthatdate
willbebilledattherevisedprice. Rebatesfor
price declines and added charges for price
3. A copy of the Return Material
Authorizationmustaccompanythereturn
shipment.
4. Freight is at the sender’s expense. All increaseswillnotbemadeforstockonhandat
partsmustbereturnedfreightprepaidto thetimeofanypricechange.
Multiquip’sdesignatedreceivingpoint.
PAGE 124 — BA-SERIES WALK-BEHIND TROWEL— OPERATION & PARTS MANUAL — REV. #2 (03/19/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
BA-SERIES WALK-BEHIND TROWEL — OPERATION & PARTS MANUAL — REV. #2 (03/19/04) — PAGE 125
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION & PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
MULTIQUIP CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
Tel. (800)-421-1244
Fax (310)-537-3927
Contact:mq@multiquip.com
MEXICO
MQ CIPSA
Carr.Fed.Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact:pmastretta@cipsa.com.mx
Tel. (52) 222-225-9900
Fax (52) 222-285-0420
UNITEDKINGDOM
MULTIQUIP (UK) LIMITED HEAD OFFICE
HanoverMill,FitzroyStreet,
Ashton-under-Lyne,
Tel. 0161 339 2223
Fax 0161 339 3226
Lancashire OL7 0TL
Contact:kcassell@multiquip.com.uk
CANADA
MULTIQUIP
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact:jmartin@multiquip.com
Tel. (450) 625-2244
Fax (450) 625-8664
BRAZIL
MULTIQUIP
Av.Evandro Lins e Silva, 840 - grupo 505
Barra deTijuca - Rio de Janeiro
RJ CEP 22631-470
Tel. 011-55-21-3433-9055
Fax 011-55-21-3433-9055
Contact:cnavarro@multiquip.com.br,srentes@multiquip.com.br
Visit our website at:www.multiquip.com
MULTIQUIP (UK)
HANOVER MILL
FITZROY STREET
ASHTON-UNDER-LYNE
LANCASHIRE, OL7 OTL
UNITED KINGDOM
PH. 0161-339-2223
FAX. 0161-339-3226
E-MAIL:mq@multiquip.com
www.multiquip.com
Atlanta • Boise • Newark •
Montreal, Canada • Manchester, UK
Rio De Janiero, BR • Puebla, MX
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Miller Electric Welder OM 234 016D User Manual
Milwaukee Saw 6278 59 User Manual
Multiquip Portable Generator CDA45SSIU3 User Manual
Niles Audio Car Amplifier SI 275 User Manual
NuTone Home Theater System 301T User Manual
Onkyo CD Player CR B8 User Manual
Optoma Technology Projection Television ES520 User Manual
Palsonic CRT Television 8010PF User Manual
Panasonic Answering Machine KX TCD545E User Manual
Parkside Paint Sprayer PFS 100 B2 User Manual