Multi Tech Equipment Trash Compactor MVH306DS2 User Manual
OperatiOn and parts Manual  
series  
MOdel MVH306ds2/  
MVH306dsCpas  
reVersiBle plate COMpaCtOr  
(YanMar l70V6GJ1r1aas5 diesel enGine)  
Revision #7 (02/04/14)  
To find the latest revision of this  
publication, visit our website at:  
www.multiquip.com  
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TAblE Of CONTENTS  
Yanmar l70V6 Diesel Engine  
MVH306DS2/MVH306DSCpAS  
Reversible plate Compactors  
Electric Device Assembly ................................ 52-53  
Cylinder Block Assembly.................................. 54-55  
Cylinder Head Assembly .................................. 56-57  
Air Cleaner Assembly....................................... 58-59  
Muffler Assembly.............................................. 60-61  
Crankshaft And Camshaft Assembly................ 62-63  
Piston Assembly............................................... 64-65  
Lub Oil Pump And Governor Assembly............ 66-67  
Cooling And Starting Device Assembly............ 68-69  
Fuel Injection Pump Assembly ......................... 70-71  
Fuel Tank And Fuel Line Assembly .................. 72-73  
Starting Motor And Dynamo Assembly ............ 74-75  
Tool, Label, And Gasket Assembly................... 76-77  
Proposition 65 Warning ........................................... 2  
Table Of Contents.................................................... 4  
Parts Ordering Procedures................................. 5-10  
Specifications ........................................................ 11  
Dimensions............................................................ 12  
General Nformation ............................................... 13  
Components .......................................................... 14  
Basic Engine.......................................................... 15  
Inspection ......................................................... 16-17  
Operation.......................................................... 18-23  
Maintenance..................................................... 24-29  
Explanation Of Code In Remarks Column............. 30  
Suggested Spare Parts ......................................... 31  
Terms And Conditions Of Sale — Parts ................ 78  
Compactor Component Drawings  
Nameplate And Decals..................................... 32-33  
Vibrating Plate Assembly.................................. 34-35  
Base And Engine Assembly ............................. 36-39  
Vibrator Assembly ............................................ 40-41  
Control Handle Assy. ....................................... 42-45  
Hand Pump Assembly...................................... 46-47  
Battery Assembly.............................................. 48-49  
Compaction Analyzing System Assembly ........... 50-51  
NOTICE  
Specifications and part numbers are subject to change  
without notice.  
page 4 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
pARTS ORDERING pROCEDuRES  
Ordering parts has never been easier!  
Choose from three easy options:  
Effective:  
January 1st, 2006  
Best deal!  
Order via internet (dealers Only):  
Order parts on-line using Multiquip’s SmartEquip website!  
If you have an MQ Account, to obtain a Username  
and Password, E-mail us at: parts@multiquip.  
com.  
I View Parts Diagrams  
I Order Parts  
I Print Specification Information  
To obtain an MQ Account, contact your  
District Sales Manager for more information.  
Use the internet and qualify for a 5% discount  
on Standard orders for all orders which include  
complete part numbers.*  
Goto www.multiquip.com and click on  
to log in and save!  
Order Parts  
Note: Discounts Are Subject To Change  
Fax your order in and qualify for a 2% discount  
on Standard orders for all orders which include  
complete part numbers.*  
Order via Fax (dealers Only):  
All customers are welcome to order parts via Fax.  
domestic (us) Customers dial:  
1-800-6-PARTS-7 (800-672-7877)  
Note: Discounts Are Subject To Change  
domestic (us) dealers Call:  
1-800-427-1244  
Order via phone:  
non-dealer Customers:  
International Customers should contact  
their local Multiquip Representatives for  
Parts Ordering information.  
Contact your local Multiquip Dealer for  
parts or call 800-427-1244 for help in  
locating a dealer near you.  
When ordering parts, please supply:  
Ì
dealer account number  
Ì
specify preferred method of shipment:  
Ì
Ì
Ì
Ì
Ì
dealer name and address  
ꢀ UPS/Fed Ex ꢀ  
Priority One ꢀ  
DHL  
Truck  
I
shipping address (if different than billing address)  
Return Fax number  
applicable model number  
I
Ground  
I Next Day  
I
Second/Third Day  
Quantity, part number and description of each part  
NOTICE  
All orders are treated as Standard Orders and will  
ship the same day if received prior to 3PM PST.  
We aCCepT aLL maJOR CRediT CaRds!  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
Do not operate or service the equipment before reading  
the entire manual. Safety precautions should be followed  
at all times when operating this equipment.  
Failure to read and understand the safety  
messages and operating instructions could  
result in injury to yourself and others.  
Potential hazards associated with the operation of this  
equipment will be referenced with hazard symbols which  
may appear throughout this manual in conjunction with  
safety messages.  
SAFETY MESSAGES  
The four safety messages shown below will inform you  
about potential hazards that could injure you or others.The  
safety messages specifically address the level of exposure  
to the operator and are preceded by one of four words:  
dangeR,WaRning, CauTiOn or nOTiCe.  
SAFETY SYMBOLS  
dangeR  
Indicates a hazardous situation which, if not avoided,  
WiLL result in DEATH or seRiOus inJuRY.  
WaRning  
Indicates a hazardous situation which, if not avoided,  
COuLd result in DEATH or seRiOus inJuRY.  
CauTiOn  
Indicates a hazardous situation which, if not avoided,  
COuLd result in minOR or mOdeRaTe inJuRY.  
NOTICE  
Addresses practices not related to personal injury.  
page 6 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
geneRaL saFeTY  
CauTiOn  
NOTICE  
„ This equipment should only be operated by trained and  
qualified personnel 18 years of age and older.  
„ neveR operate this equipment without proper protective  
clothing, shatterproof glasses, respiratory protection,  
hearing protection, steel-toed boots and other protective  
devices required by the job or city and state regulations.  
„ Whenever necessary, replace nameplate, operation and  
safety decals when they become difficult read.  
„ Manufacturer does not assume responsibility for any  
accident due to equipment modifications. Unauthorized  
equipment modification will void all warranties.  
„ neveR use accessories or attachments that are not  
recommended by Multiquip for this equipment. Damage  
to the equipment and/or injury to user may result.  
„ neveR operate this equipment when not  
feeling well due to fatigue, illness or when  
under medication.  
„ ALWAYS know the location of the nearest  
„ neveR operate this equipment under the influence of  
drugs or alcohol.  
fire extinguisher.  
„ ALWAYS know the location of the nearest  
first aid kit.  
„ ALWAYS know the location of the nearest phone or keep  
a phone on the job site. Also, know the phone numbers  
of the nearest ambulance,doctorand fire department.  
This information will be invaluable in the case of an  
emergency.  
„ ALWAYS check the equipment for loosened threads or  
bolts before starting.  
„ dO nOT use the equipment for any purpose other than  
its intended purposes or applications.  
„ ALWAYS clear the work area of any debris, tools, etc.  
that would constitute a hazard while the equipment is  
in operation.  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
COMPACTOR SAFETY  
WaRning  
dangeR  
„ dO nOT place hands or fingers inside engine  
compartment when engine is running.  
„ neveRoperate the equipment in an explosive  
atmosphere or near combustible materials.An  
explosion or fire could result causing severe  
bodily harm or even death.  
„ neveR operate the engine with heat shields or  
guards removed.  
„ Keep fingers, hands hair and clothing away  
from all moving parts to prevent injury.  
WaRning  
„ neveR disconnect any emergency or safety devices.  
These devices are intended for operator safety.  
Disconnection of these devices can cause severe injury,  
bodily harm or even death.Disconnection of any of these  
devices will void all warranties.  
„ dO nOT remove the radiator cap while the  
engine is hot. High pressure boiling water will gush out  
of the radiator and severely scald any persons in the  
general area of the compactor.  
„ dO nOT remove the coolant drain plug  
while the engine is hot. Hot coolant will  
gush out of the coolant tank and severely  
scald any persons in the general area of  
the compactor.  
CauTiOn  
„ neveR lubricate components or attempt service on a  
running machine.  
NOTICE  
„ dO nOT remove the engine oil drain plug while the  
engine is hot. Hot oil will gush out of the oil tank and  
severely scald any persons in the general area of the  
compactor.  
„ ALWAYS keep the machine in proper running condition.  
„ Fix damage to machine and replace any broken parts  
immediately.  
CauTiOn  
„ ALWAYS store equipment properly when it is not being  
used.Equipment should be stored in a clean, dry location  
out of the reach of children and unauthorized personnel.  
„ neveR touch the hot exhaust manifold,  
muffler or cylinder.Allow these parts to cool  
before servicing equipment.  
engine saFeTY  
dangeR  
NOTICE  
„ neveR run engine without an air filter or with a dirty air  
filter.Severe engine damage may occur.Service air filter  
frequently to prevent engine malfunction.  
„ The engine fuel exhaust gases contain poisonous carbon  
monoxide. This gas is colorless and odorless, and can  
cause death if inhaled.  
„ neveR tamper with the factory settings  
of the engine or engine governor. Damage  
to the engine or equipment can result  
if operating in speed ranges above the  
maximum allowable.  
„ The engine of this equipment requires an adequate  
free flow of cooling air. neveR operate this equipment  
in any enclosed or narrow  
area where free flow of the  
air is restricted. If the air  
flow is restricted it will cause  
„ neveR tip the engine to extreme angles during lifting as  
it may cause oil to gravitate into the cylinder head, making  
the engine start difficult.  
injury to people and property  
and serious damage to the  
equipment or engine.  
page 8 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
FueL saFeTY  
dangeR  
BaTTeRY saFeTY (eLeCTRiC sTaRT OnLY)  
dangeR  
„ dO nOT add fuel to equipment if it is placed inside truck  
bed with plastic liner. Possibility exists of explosion or  
fire due to static electricity.  
„ dO nOT drop the battery. There is a possibility that the  
battery will explode.  
„ dOnOTexpose the battery to open flames,  
sparks, cigarettes, etc.The battery contains  
combustible gases and liquids. If these  
gases and liquids come into contact with a  
flame or spark, an explosion could occur.  
-306  
H
V
M
WaRning  
„ ALWAYS wear safety glasses when  
handling the battery to avoid eye irritation.  
The battery contains acids that can cause  
injury to the eyes and skin.  
MVH-306  
„ Use well-insulated gloves when picking up  
the battery.  
„ ALWAYS keep the battery charged. If the battery is not  
charged, combustible gas will build up.  
„ dO nOTstart the engine near spilled fuel or combustible  
fluids. Diesel fuel is extremely flammable and its vapors  
can cause an explosion if ignited.  
„ dO nOT charge battery if frozen. Battery can explode.  
When frozen, warm the battery to at least 61°F (16°C).  
„ ALWAYS refuel in a well-ventilated area, away from  
sparks and open flames.  
„ ALWAYS recharge the battery in a well-ventilated  
environmenttoavoidtheriskofadangerousconcentration  
of combustible gases.  
„ ALWAYS use extreme caution when working with  
flammable liquids.  
„ If the battery liquid (dilute sulfuric acid)  
comes into contact with clothing or skin,  
rinse skin or clothing immediately with  
plenty of water.  
„ dO nOT fill the fuel tank while the engine is running  
or hot.  
„ dO nOT overfill tank, since spilled fuel could ignite if it  
comes into contact with hot engine parts or sparks from  
the ignition system.  
„ If the battery liquid (dilute sulfuric acid) comes into  
contact with eyes, rinse eyes immediately with plenty  
of water and contact the nearest doctor or hospital to  
seek medical attention.  
„ Store fuel in appropriate containers, in well-ventilated  
areas and away from sparks and flames.  
CauTiOn  
„ neveR use fuel as a cleaning agent.  
„ ALWAYS disconnect the negaTive battery terminal  
before performing service on the equipment.  
„ dO nOT smoke around or near the  
equipment. Fire or explosion could result  
from fuel vapors or if fuel is spilled on a  
hot engine.  
„ ALWAYS keep battery cables in good working condition.  
Repair or replace all worn cables.  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAfETY INfORMATION  
„ When the life cycle of this equipment is over, remove  
battery and bring to appropriate facility for lead  
reclamation. Use safety precautions when handling  
batteries that contain sulfuric acid.  
TRanspORTing saFeTY  
CauTiOn  
„ NEVER allow any person or animal to stand underneath  
the equipment while lifting.  
„ When the life cycle of this equipment is over, it is  
recommended that the trowel frame and all other metal  
parts be sent to a recycling center.  
NOTICE  
Metal recycling involves the collection of metal from  
discarded products and its transformation into raw  
materials to use in manufacturing a new product.  
„ Before lifting, make sure that the equipment parts (hook  
and vibration insulator) are not damaged and screws are  
not loose or missing.  
Recyclers and manufacturers alike promote the process  
of recycling metal. Using a metal recycling center  
promotes energy cost savings.  
„ Always make sure crane or lifitng device has been  
properly secured to the lifting bail (hook) of the  
equipment.  
emissiOns inFORmaTiOn  
„ ALWAYS shutdown engine before transporting.  
NOTICE  
„ neveR lift the equipment while the engine is running.  
The diesel engine used in this equipment has been  
designed to reduce harmful levels of carbon monoxide  
(CO), hydrocarbons (HC) and nitrogen oxides (NOx)  
contained in diesel exhaust emissions.  
„ Tighten fuel tank cap securely and close fuel cock to  
prevent fuel from spilling.  
„ Use adequate lifting cable (wire or rope) of sufficient  
strength.  
This engine has been certified to meet US EPA Evaporative  
emissions requirements in the installed configuration.  
„ Use one point suspension hook and lift straight  
upwards.  
Attempting to modify or make adjustments to the engine  
emission system by unauthorized personnel without proper  
training could damage the equipment or create an unsafe  
condition.  
„ dO nOT lift machine to unnecessary heights.  
„ ALWAYS tie down equipment during transport by  
securing the equipment with rope.  
Additionally, modifying the fuel system may adversely affect  
evaporative emissions, resulting in fines or other penalties.  
enviROnmenTaL saFeTY/deCOmmissiOning  
NOTICE  
emission Control Label  
Decommissioning is a controlled process used to safely  
retire a piece of equipment that is no longer serviceable.  
If the equipment poses an unacceptable and unrepairable  
safety risk due to wear or damage or is no longer cost  
effective to maintain (beyond life-cycle reliability) and is to  
be decommissioned (demolition and dismantlement),be  
sure to follow rules below:  
The emission control label is an integral part of the emission  
system and is strictly controlled by regulations.  
The label must remain with the engine for its entire life.  
If a replacement emission label is needed, please contact  
your authorized Kohler Engine Distributor.  
„ dO nOT pour waste or oil directly onto the ground, down  
a drain or into any water source.  
„ Contact your country's Department of  
Public Works or recycling agency in your  
area and arrange for proper disposal of  
any electrical components, waste or oil  
associated with this equipment.  
page 10 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SpECIfICATIONS  
Table 1. mvh306ds2/dsCpas Reversible  
plate Compactor specifications  
Centrifugal Force  
10,116 lbs. (4,588 kg)  
vibration Frequency  
Traveling speed  
plate size (L xW)  
3,600 vpm (60 Hz)  
0 to 75 ft/min (0 to 23 m/min)  
18 x 34 in (45.72 x 86.36 cm)  
24 x 34 in (60.96 x 86.36 cm)  
6,750 sq. ft. (2,057 sq. meters)  
62 in (1,575 mm)  
external plate size (L xW)  
max. area of Compaction (no extensions)  
Overall Length  
OverallWidth  
18.0 in (457 mm )  
Overall height (with handle)  
Overall height (without handle)  
Operating Weight  
55 in (1,397 mm )  
34 in (864 mm )  
725 lbs. (329 kg.)  
Operating Weight (extension plates)  
Lubricating Oil in vibration Case  
824 lbs. (374 kg.)  
20.28 fl. oz. (600 cc)  
Table 2. engine specifications  
engine make  
engine model  
Engine Type  
YANMAR  
L70V6GJ1R1AAS5  
Air-cooled 4-cycle Diesel Engine  
3.07 x 2.51 in (78 x 64 mm)  
10.34 fl oz (306 cm3)  
Cylinder Bore X stroke  
displacement  
maximum Ouput  
6.5 HP @3,600 RPM  
FuelTank Capacity  
Oil Capacity  
3.5 quarts (3.31 liters)  
1.16 quarts (1.10 liters)  
starting method d/ds  
dry netWeight Recoil/electric  
dimensions (L xW x h)  
Recoil/Electric  
72.75 lbs. (33 kg)/83.77 lbs. (38 kg)  
15.11 x 16.57 x 17.71 in (384 x 421 x 450 mm)  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIMENSIONS  
MVH-306  
A
E
C
B
D
Figure 1. MVH306DS2/DSCPAS Reversible Plate  
Compactor Dimensions  
Table 3. dimensions  
A
B
55 in. (1,387 mm.)  
18 in. (445 mm.)  
C
D
E
34 in. (860 mm.)  
62 in. (1570 mm.)  
34 in. (856 mm.)  
page 12 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GENERAl NfORMATION  
plate Compactor  
Frequency/speed  
The Mikasa MVH306DS2/DSCPAS is a walk behind,  
reversible plate compactor designed for the compaction of  
sand, clay and asphalt.This plate compactor is a powerful  
compacting tool capable of applying a tremendous force in  
consecutive high frequency vibrations to a soil surface. Its  
applications include soil compacting for road, embankments  
and reservoirs as well as backfilling for gas pipelines, water  
pipelines and cable installation work.  
The compactor's vibrating plate maximum frequency is  
4400 vpm (vibrations per minute).The forward and reverse  
travel speed of the compactor is approximately 75 ft./minute  
(23 meters/minute).  
Engine  
This plate compactor is equipped with a YANMAR  
L70V6GJ1R1AAS5 diesel engine.  
vibratory plates  
Controls  
The vibratory plates of this plate compactor produce low  
amplitude high frequency vibrations, designed to compact  
granular soils.  
Before starting this plate compactor, identify and understand  
the function of the controls and all components.  
The resulting vibrations cause forward motion.The engine  
and handle are vibration isolated from the vibrating plate.  
The heavier the plate, the more compaction force it  
generates.  
Reversible vibratory plates  
Reversible vibratory plates have two eccentric weights that  
allow a smooth transition for forward and reverse travel, plus  
increased compaction force as the result of dual weights.  
Due to their weight and force, reversible plates are ideal  
for semi-cohesive soils.  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMpONENTS  
16  
2
10  
1
4
12  
14  
15  
3
MVH-306  
6
5
9
7
13  
12  
11  
8
Figure 2. MVH306DS2/DSCPAS Reversible Plate Compactor Components  
Figure 2 illustrates the location of the major components for  
the MVH306DS2/DS2CPAS Reversible Plate Compactor.  
The function of each component is described below:  
8. Belt Cover – Remove this cover to gain access to the  
V-belts. neveR run the compactor without the V-belt  
cover. If the V-belt cover is not installed, the possibility  
exist that your hand may get caught between theV-belt  
and clutch, thus causing serious injury and bodily harm.  
1. hand grip – When operating the compactor use this  
hand grip to maneuver the compactor.  
9. Base plate – Designed to compact sand, clay, and  
asphalt.  
2. Forward & Reverse Lever – Push the lever forward,  
the compactor will move in a forward direction, pull the  
lever backwards, the compactor will move in backwards  
direction. Placing the lever in the middle (midway) will  
cause the compactor not to move (neutral).  
10. Oil Reservoir – Fill with Shell Tellus Oil 46 or  
equivalent grade hydraulic oil.  
11. vibration Case – Encloses the eccentric, gears and  
counter weights.  
3. handle Bar – When operating the compactor, this  
handle is to be in the downward position. When the  
compactor is to be stored, move the handle bar to  
the upright position.  
12. hydraulic Cylinder – Activated by moving the travel  
lever. The cylinder controls the direction of movement  
by the plate compactor.  
4. guard hook - Used to lift the machine with crane or  
other lifting device.  
13. shock absorber – Protects plate compactor from  
damage by absorbing vibration during operation.  
5. Stopper - Locks the handle in place in the upward  
position for stowing.  
14. Throttle Lever – Controls speed of the plate  
compactor. Place straight vertically to start, push fully  
counterclockwise for full throttle and fully clockwise to  
stop plate compactor.  
6. Engine – This plate compactor uses a YANMAR  
L-70V6 diesel engine. Refer to the owner’s manual for  
engine information and related topics.  
15. ignition switch (Option) – Provided for electric start  
models only.  
7. Battery (Option) -This unit uses a 12-volt battery.See  
maintenance of this manual for proper care of battery.  
16. COMPAS – Compaction Analysing System, monitors  
soil stiffness. Available only on the MVH306DSCPAS.  
page 14 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bASIC ENGINE  
9
3
4
1
2
10  
5
7
6
8
Figure 3. Yanmar L70V6 Engine Components  
engine COmpOnenTs  
Figure 3 illustrates the location of the major components  
for the Yanmar L70V6 diesel engine. The function of each  
component is described below  
6. Recoil Starter – Manual-starting method. Pull the  
starter grip until resistance is felt, then pull briskly and  
smoothly.  
1. Fuel Filler Cap – Remove this cap to add unleaded  
gasoline to the fuel tank. Make sure cap is tighten  
securely. dO nOT over fill.  
7. Oil Filler Cap / dipstick – Remove this cap to add oil  
to the engine crankcase. Read dipstick to determine if  
oil level is low. dO nOT over fill.  
2. Fuel Tank – Capacity is 3.5 quarts (3.31 liters) of  
diesel fuel.  
8. Oil Drain Plug – Unscrew plug to drain oil from engine  
crankcase. Dispose of oil in a safe manner.  
3. Air Cleaner – Prevents dirt and other debris from  
entering the fuel system. Remove wing-nut on top of  
air filter cannister to gain access to filter element.  
9. decompression Lever – Press down before starting  
engine.To prevent damage to engine, dO nOT use for  
any other purpose.  
4. muffler – Used to reduce noise and emissions.  
10. Fuel Cock – Controls the flow of diesel fuel to the  
carburetor. Must be in the ON position when starting  
and running the engine.  
5. Recoil starting handle (pull rope) – Type of engine  
starting method. Alternate type would be electric start  
(ignition key).  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSpECTION  
UPPER  
LEVEL  
Before starting  
1. Read safety instructions at the beginning  
of manual.  
2. Familiarize yourself with the operating and control  
elements of the machine and the working environment.  
This includes obstacles in the working area, bearing  
capacity of the ground and the necessary safety  
provisions.  
LOWER  
LEVEL  
3. Check the air filter for dirt and dust. If air filter is dirty,  
replace air filter with a new one as required.  
Figure 5. Engine Oil Level  
4. Check fastening nuts and bolts for tightness. Loose  
threads may cause damage to the machine when  
vibrating.  
Table 4. Oil Tyoe  
season  
Temperature  
Oil Type  
5. Understand the geographical features and regulations  
of the job site.  
Summer  
25°C or Higher  
SAE 10W-30  
SAE 10W-  
30/20  
6. Clean the compactor, removing dirt and dust.  
Particularly, the bottom of the plate, engine cooling  
air inlet.  
Spring/Fall  
Winter  
25°C~10°C  
0°C or Lower  
SAE 10W-10  
Checking engine Oil Level  
Checking the hydraulic Oil Level  
1. To check the engine oil level, place the compactor on  
secure level ground with the engine stopped.  
1. To check the engine oil level, place the compactor on  
secure level ground with the engine stopped.  
2. Remove the dipstick from the engine oil filler hole  
(Figure 4) and wipe it clean.  
2. Remove the hydraulic oil breather cap located at the  
top of the hydraulic oil tank (Figure 6).  
3. Insert and remove the dipstick without screwing it into  
the filler neck.Check the oil level shown on the dipstick.  
3. Using a 24 mm wrench, remove the hydraulic oil filler  
plug.  
4. Visually inspect to determine if hydraulic oil level is  
low. If oil level is low add Shell Tellus 46 hydraulic oil or  
equivalent through the hand pump oil filler port.  
OIL  
TANK  
BREATHER  
CAP  
Figure 4. Engine Oil Dipstick Removal  
4. If the oil level is low (Figure 5), fill to the edge of the  
oil filler hole with the recommended oil type (Table 4).  
Maximum oil capacity is 1.16 quarts (1.10 liters).  
HYDRAULIC  
OIL PLUG  
(24 MM WRENCH)  
Figure 6. Hydraulic Oil Filler Plug Removal  
page 16 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSpECTION  
3. Remove the air cleaner element (Figure 9) and inspect  
it for signs of wear or dirt. If air cleaner element is dirty,  
clean or replace element.  
CauTiOn  
dO nOT overfill hydraulic oil tank. This could cause  
oil leaks and sluggish operation. Clean cap and  
surrounding area before opening to prevent dirt from  
entering oil tank.  
ELEMENT  
5. When adding hydraulic oil, only fill to the specified oil  
level as marked on the front of the hydraulic oil tank  
(Figure 7). dO nOT overfill.  
OIL  
TANK  
Figure 9. Air Cleaner Element  
OIL LEVEL  
dangeR  
eXpLOsive FueL!  
Motor fuels are highly flammable and can  
be dangerous if mishandled. dO nOT  
smoke while refueling. dO nOT attempt  
to refuel if the engine is hot or running.  
Figure 7. Oil Tank (Front View)  
CheckingThe Fuel  
Checking the air Cleaner  
1. Remove the fuel cap located on top of fuel tank.  
1. To check the engine oil level, place the compactor on  
secure level ground with the engine stopped.  
2. Visually inspect to see if fuel level is low. If fuel is low,  
replenish with diesel fuel (Figure 10 ).  
2. Loosen the wing nut (Figure 8), remove the air cleaner  
cover.  
3. When refueling, be sure to use a strainer for filtration.  
dO nOT top-off fuel. Wipe up any spilled fuel.  
AIR  
CLEANER  
WING  
NUT  
Figure 8. Checking the Air Cleaner  
Figure 10. Refueling  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OpERATION  
3. When the handle is raised to the desired height, tighten  
the butterfly screw.  
CauTiOn  
dOnOTattempt to operate the compactor  
until the Safety, General Information and  
Inspection sections of this manual have  
been read and thoroughly understood.  
This section is intended to assist the operator with the initial  
start-up of the compactor. It is extremely important that  
this section be read carefully before attempting to use the  
compactor in the field.  
Figure 12. Handle Adjustment  
Refer to Figure 3 for the location of controls and components.  
Releasing the Handle  
sTaRTingThe engine  
Electric Start (Option)  
1. Pull the handle release pin, (Figure 11) then push down  
on the hand grip to release the handle.  
1. Place the fuel cock (Figure 13) in the open position.  
MVH-306  
Figure 13. Fuel Cock Open Position)  
2. Place the throttle lever (Figure 14) in the START  
position (center). Place the travel lever in the neutral  
position (center)  
TRAVEL  
LEVER  
HANDLE  
RELEASE  
PULL UP  
PIN  
NEUTRAL  
REVERSE  
TO RELEASE  
HANDLE  
FORWARD  
THROTTLE  
LEVER  
Figure 11. Handle Release Pin  
adjusting handle height  
START  
(CENTER POSITION)  
The height of the handle is adjustable for your comfort .  
1. Loosen the butterfly screw (Figure 12).  
Figure 14. Travel/Throttle Lever  
(Start Position)  
2. Turn the grip clockwise to raise the handle or  
counterclockwise to lower the handle.  
page 18 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OpERATION  
Recoil Start  
NOTICE  
1. Place the fuel cock in the Open position (Figure 13).  
When starting a unit with an electric strart capability, a  
decompressor is not normally required.However, when  
ambient temperature or battery charger level is low, use  
of a decompressor will help make the start-up easier.  
2. Move the throttle lever to the START position  
(Figure 14).  
3. Grasp the starter grip (Figure 16) and slowly pull it  
out. The resistance becomes the hardest at a certain  
position, corresponding to the compression point. Pull  
the starter grip briskly and smoothly for starting.  
3. Insert the ignition key into the ignition switch and turn  
it to the Run position (Figure 15). The buzzer should  
sound at this time.  
4. Turn the ignition key further to the right to the START  
position to start the engine.Buzzer stops sounding and  
the engine starts.  
5. If the engine fails to start, dO nOT continue to rotate  
the ignition key for more than 5 seconds. Return the  
key to the Run position and wait 10 seconds before  
starting again  
Figure 16. Engine Start Handle  
STOP  
RUN  
4. Push down decompression lever (Figure 17) and  
release.  
START  
Figure 15. Starter Switch (Option)  
;
CauTiOn  
While the engine is running, never try to turn the ignition  
key to the START position.  
6. After starting the engine, continue to warm up the  
engine for about 3 to 10 seconds especially in cold  
weather.  
Figure 17. Decompression Lever  
7. If the buzzer does not stop sounding after the engine  
has started, shutdown engine immediately and check  
engine oil level. The buzzer functions as a engine oil  
level alarm warning device.  
5. If the engine does not start, repeat steps 1 thru 4  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OpERATION  
4. To make the compactor move in the reverse direction  
pull the travel lever ( Figure 19) backwards.  
TRaveLing  
CauTiOn  
5. Firmly gasp the compactor's hand grip, the compactor  
will begin moving in the desired position when the  
direction lever has been placed in the desired position.  
Make sure to follow all safety rules referenced in  
the safety section of this manual before operating  
compactor. Keep work area clear of debris and other  
objects that could cause damage to the compactor or  
bodily harm.  
6. Slowly walk behind the compactor and be on the  
lookout for any large objects or foreign matter that  
might cause damage to the compactor or bodily injury.  
1. Grasp the compactor's hand grip, and move the engine  
throttle lever (Figure 18) quickly to the fast position.  
7. If travel lever is placed in the neutral position, the  
machine will vibrate in place.  
2. With the throttle lever in the fast position, the engine  
speed should be around 3,600 RPM, therefore  
engaging the centrifugal clutch.  
8. To move the compactor laterally, hold the hand grip  
firmly and swing compactor. dOnOTswing compactor  
while gripping the travel lever.  
HAND  
GRIP  
normal shutdown  
1. Return the throttle lever to the START position  
(Figure 14). Allow the machine to cool down for 2 to  
3 minutes.  
FULL THROTTLE  
POSITION  
2. Place the travel lever in the neuTRaLposition (Figure 20).  
3. Place the throttle lever in the STOP position (Figure 20)  
to stop the engine.  
Figure 18. Throttle Lever (Fast)  
NOTICE  
TRAVEL  
LEVER  
ALWAYS move the throttle lever quickly without  
hesitation, because increasing the engine speed slowly  
causes the clutch to slip.  
NEUTRAL  
POSITION  
3. To make the compactor move in the forward direction  
push the travel lever ( Figure 19) forward.  
STOP  
POSITION  
TRAVEL  
LEVER  
THROTTLE  
LEVER  
NEUTRAL  
REVERSE  
Figure 20. Throttle Lever (Stop)  
FORWARD  
Figure 19. Travel Lever  
page 20 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OpERATION  
4. If using an electric start unit, return the key switch to the  
STOP position (Figure 21) as soon as the engine stops.  
emergency shutdown  
1. For a recoil start type engine, move the throttle lever  
quickly to the STOP position.  
2. For an electric start type engine, place the engine  
ignition switch in the OFF position.  
sTOWingThe handLe  
1. Push up the handle upward (Figure 23) until the handle  
locks in place.  
Figure 21. Starter Switch (STOP)  
5. Place the fuel cock (Figure 22) in the closed position.  
MVH-306  
Figure 22. Fuel Cock (Closed Position)  
Figure 23. Stowing The Handle  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OpERATION  
When the plate compactor is in idle mode the green LED  
will begin flashing and the red LED will turn on. As the  
engine RPM's are increased and compaction begins, the  
green LED will stop flashing and turn on (solid). The red  
LED will turn off and the #1 yellow LED will turn on. As  
compaction progresses the number of yellow LEDs, 2 thru  
8 will turn on (Figure 25).  
COmpaCTiOn sensOR (mvh306 dsCpas Only)  
Compaction Analyzing System (COMPAS) is a system that  
uses an acceleration sensor to show real-time soil stiffness  
via LED's (light-emitting diode) turning on with each pass  
of the compactor.  
This COMPAS improves compaction work efficiency  
because it can prevent an already properly compacted area  
from being compacted more than necessary and identify  
an area where more compaction is needed.  
The number of yellow status LEDs that will turn on is soil  
dependent.  
NORMAL OPERATION  
(GREEN LED ON)  
COMPAS also has a function to detect abnormalities such  
as vibration trouble (insufficient vibration frequency), ground  
trouble (soft soil) and other functional issues (Figure 24).  
NORMAL OPERATION  
(GREEN LED ON)  
COMPACTION LIMIT  
LED’S 1 THRU 8 ON  
PLUS RED LED ON  
VIBRATION ABNORMALITY  
(GREEN LED FLASHING)  
SOIL PROBLEM,  
GREEN, AND RED  
LED’S ON  
INITIAL COMPACTION YELLOW LED#1 ON  
COMPACTION PROGRESSION LED’S 2 THRU 8 ON  
COMPACTION PROGRESSION LED’S 1 THRU 8 ON  
Figure 25. Compaction Progression  
Figure 24. Compaction Sensor (COMPAS)  
normal Compaction (Compaction Limit)  
NOTICE  
The compaction limit (Figure 26) is achieved when all the  
yellow LED's 1 thru 8 including the red LED are all on,  
depending on type of soil being compacted . At this point  
the machine cannot compact any further.If the compaction  
results are not satisfactory then check and make sure the  
soil type, moisture content, lift and number of passes are  
proper for this machine.  
COMPAS can only show progression of the soil stiffness  
and is not meant to measure absolute soil density.  
When using COMPAS always calculate appropriate soil  
density by conducting proper testing such as plate load  
test and dynamic load test to best compliment the LED  
lighting progression with the actual measurement value.  
DURING COMPACTION YELLOW  
LED’S 1 THRU 8 ON  
normal Compaction (Compaction progression)  
NOTICE  
Not all yellow status LEDs will turn on.The progression  
of the yellow status LEDs depends on the type of  
soil being compacted. If compacting gravel (stiff soil)  
potentially all status LEDs will turn ON.  
RED LED ON  
If compacting sand (soft soil), fewer status LED's will  
turn ON. Remember dO nOT over compact.  
Figure 26. Compaction Limit  
page 22 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OpERATION  
VIBRATION ABNORMALITY DUE TO  
IMPROPER ENGINE RPM  
system diagnostics to detect Operational  
abnormalities  
GREEN LED  
FLASHING  
Detection of ground trouble and soft ground  
1. For a case of unstable ground or soft ground (soil  
containing high clay content) for which the use of this  
machine is not suitable, only the green and red LEDs  
will be on (Figure 27), with no yellow LED's on.  
Figure 28. Vibration Abnormality  
Improper Engine RPM's  
If this occurs it would be challenging to achieve the  
desired compaction results. Check to make sure the  
ground conditions are prepared to specification before  
proceeding with the compaction process.  
Function to detect electric system abnormality  
Sensor wire disconnection (between acceleration  
sensor and sensor panel)  
GROUND TROUBLE  
GREEN  
LED ON  
OR  
SOFT GROUND  
3. If red and green LEDs are flashing alternately as shown  
in Figure 29 then please check the sensor wire because  
there is a possibility that it is disconnected.  
RED  
LED ON  
RED LED  
FLASHING  
Figure 27. Ground Trouble or Soft Ground  
Detection of Vibration Abnormality  
2. When appropriate vibration frequency cannot be  
achieved during operation due to improper engine  
RPMs (Figure 28) the green LED will flash. When this  
occurs check the engine RPMs and the V-belt tension  
as it could be loose.  
GREEN LED  
FLASHING  
Figure 29. Sensor Wire Disconnection  
Power cable disconnection (between battery and  
sensor panel)  
4. If there are no LEDs on or flashing even when the key  
switch is turned on then please check the power cable  
because there is a possibility it is disconnnected.  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
Table 6. mvh-306ds2/dsCpas engine Check  
CauTiOn  
item  
hours of Operation  
Inspection and other services should always be carried  
out on hard and level ground with the engine shutdown.  
Oil or Fuel Leak  
Every 8 hours (every day)  
inspection and maintenance serviceTables.  
Tightness of Fastening  
Threads  
Every 8 hours (every day)  
To make sure your plate compactor is always in good  
working condition before using, carry out the maintenance  
inspection in accordance with Table 5 thru Table 7.  
Every 8 hours (every day) (Re-  
plenish to specified maximum  
level)  
Engine Oil Check and Re-  
plenishment  
Table 5. mvh-306ds2/dsCpas machine inspection  
After first 25 hours then every 50  
to 100 hours  
Engine Oil Replacement  
Air Filter Cleaning Every  
item  
hours of Operation  
100 hours  
Loose or Missing Screws  
Every 8 hours (every day)  
See separate engine manual for details on engine check.  
Damaged Parts  
Every 8 hours (every day)  
daily service  
Function of Controlling  
System Part  
Every 8 hours (every day)  
Every 100 hours  
„ Check for leakage of fuel or oil.  
Hydraulic System Leak  
Vibrator Oil Check Every  
Vibrator Oil Replacement  
Hydraulic Oil Check Every  
Hydraulic Oil Replacement  
V-belt (clutch) Check  
„ Check for loose screws including tightness. See Table 7  
below (tightening torque ), for retightening:  
Every 100 hours  
Table 7. TighteningTorque  
(in. kg/cm) diameter  
Every 300 hours  
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm  
Every 100 hours  
4T  
70 150 300 500 750 1,100 1,400 2,000  
First after 200 hours, then every  
1,000 hours  
6-8T 100 250 500 800 1,300 2,000 2,700 3,800  
11T  
*
150 400 800 1,200 2,000 2,900 4,200 5,600  
Every 200 hours  
Every 100 hours  
300~ 650~  
100  
350 700  
Battery Check  
* (In case counter-part is of aluminum)  
(Threads in use with this machine are all right handed)  
Material and quality of material is marked on each bolt, and screw.  
CauTiOn  
„ Remove soil and clean the bottom of compaction plate.  
These inspection intervals are for operation under  
normal conditions. Adjust your inspection intervals  
based on the number hours plate compactor is in use,  
and particular working conditions.  
„ Check hand pump, piping and hose for any leakage. A  
loosened hydraulic hose can be a cause for leakage.  
Check hydraulic hose connections with wrench applied  
for tightness.  
„ Check engine oil.  
NOTICE  
Fuel piping and connections should be replaced every  
2 years.  
page 24 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
engine Oil Replacement:  
1. Replace engine oil, in first 25 hours of operation and  
every 50 to 100 hours afterwards.  
CLUTCH  
V-BELT  
2. Oil may be drained more easily when it is warm  
afteroperation (For more details, see separate engine  
Owner's Manual).  
VIBRATOR PULLEY  
BELT COVER  
air Filter (every 6 months or 400 hours)  
1. The air filter element (Figure 30) should be cleaned  
because a clogged air cleaner can cause poor  
engine starting, lack of power and shorten engine life  
substantially.  
Figure 32. V-Belt Check  
Replacing the v-belt  
„ Remove the belt cover (Figure 32). Engage an offset  
wrench 3/4”(19 mm) or the like to vibrator pulley (lower)  
fastening bolt. Engage wastecloth or the like at midway  
ofV-belt on the left side and whilepulling it back strongly,  
rotate the offset wrench clockwise so that the V-belt will  
come off.  
Reinstalling the v-belt  
Figure 30. Engine Air Filter and Element  
„ EngageV-belt to lower vibrator pulley and push theV-belt  
to leftside of upper clutch and, in the same manner as  
in removal, rotate offset wrench clockwise so that the  
V-belt goes back on.  
2. To clean or replace air filter loosen the wing nut on the  
air filter housing (Figure 30) remove the cover and take  
out air filter cartridge. If only cleaning of the air filter  
is desired blow through the air filter cartridge from the  
inside, moving a jet of dry compressed air up and down  
until all dust is removed.  
Checking Clutch  
„ Check the clutch simultaneously with V-belt checking.  
With belt cover removed, check outer drum of the clutch  
for seizure and "V" groove for wear or damage with your  
eyes. Clean the "V" groove as necessary. If the shoe is  
worn, power transmission becomes deficient and slipping  
will result.  
CauTiOn  
neveR attempt to check the V-belt with the engine  
running. Severe injury can occur if your hand gets  
caught between the V-belt and the clutch (Figure 31).  
Always use safety gloves.  
Replacing Clutch  
„ Remove V-belt. Remove bolt at engine power output by  
giving a light tap with a hammer to an engaged wrench  
and rotate bolt counterclockwise. Remove clutch with a  
pulley extractor. To reinstall, reverse the procedure.  
CLUTCH  
PULLEY  
CauTiOn  
When ever the compactor's vibration becomes weak  
or lost during normal operation regardless of operation  
hours, check the V-belt and clutch immediately.  
VIBRATOR  
PULLEY  
Figure 31. V-Belt Hazard  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
4. After hydraulic oil has been completely drained from  
machine, fill with 10W-30 motor oil to the appropriate  
safe operating level (Figure 33).  
vibrator Oil Level Check  
NOTICE  
ALWAYS clean the area around the vibrator oil level  
check plug before removing oil check plug. This will  
prevent dirt and debris from entering the system.  
5. Reinstall drain plug into vibrating plate assembly.Apply  
seal tape or Loctite #575 to thread portion of drain plug.  
draining hydraulic Oil  
1. In every 100 hours of operation, with the machine  
positioned horizontally, use a 3/4”(19 mm) wrench and  
remove vibratoroil level check plug (Figure 33).Visually  
inspect and see if vibrator oil level is up to filler port.  
Be sure to clean area around check hole to prevent  
dirt and dust from entering.  
1. Disconnect the hydraulic hose (Figure 34) connected  
to the hydraulic oil cylinder.  
2. Push the travel lever back and forth to drain the hydraulic  
oil from the hand pump (hydraulic oil reservoir).  
HYDRAULIC  
HOSE  
OILGAUGE/  
DIPSTICK  
ADD 10W-30 WT.  
MOTOR OIL  
HERE  
DRAIN  
BOLT  
HYDRAULIC  
CYLINDER  
OILGAUGE/  
DIPSTICK  
CORRECT  
Figure 34. Hydraulic Oil Cylinder/Hose  
FILL TO 600CC  
MAXIMUM  
DRAIN  
BOLT  
3. After draining hydraulic oil, reconnect hydraulic oil  
hose to cylinder.  
EXCITER OIL LEVEL CASING NORMAL  
INCORRECT  
4. Place handle in upright position.Pull travel lever all the  
way back (reverse), and using a rope, secure travel  
lever to hand grip.  
EXCITER OIL LEVEL CASING OVERFILLED  
adding hydraulic Oil  
Figure 33. Vibrator Oil Drain and Check Plugs  
1. Remove the breather cap and oil plug (Figure 35) from  
thehydraulic oil tank using a 24mm hex socket.  
draining vibrator Oil  
1. Replace vibrator oil after first 200 hours and in every  
1,000 hours of operation. Oil capacity is 600 cc.  
OIL  
TANK  
BREATHER  
CAP  
2. Position handle bar vertically (storage position).  
3. Using a 14 mm wrench remove the vibrator oil drain  
plug (Figure 33) from the vibrating plate assembly.  
HYDRAULIC  
OIL PLUG  
(24 MM WRENCH)  
NOTICE  
For draining oil through level check hole, have the  
machine inclined with a sleeper or the like placed under  
the compaction plate on opposite side.  
Figure 35. Hydraulic Oil Tank  
page 26 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
2. Using a funnel, add Shell Tellus Oil #32 or equivalent  
to the hydraulic oil tank through the oil filler port  
(Figure 36). Oil tank capacity is 18.7 fl. oz (550 cc).  
CauTiOn  
ALWAYS wear safety glasses or face mask, protective  
clothes, and rubber gloves when working with battery.  
HYDRAULIC  
OIL TANK  
BaTTeRY mainTenanCe (Option)  
S
H
T
E
L
FILL TO  
THIS LEVEL  
E
0I  
L
L
L
U
L
S
#
4
Mishandling of the battery shortens the service life of the  
battery and adds to maintenance cost.When handling the  
battery do the following:  
6
OIL LEVEL  
„ The battery electrolyte contains sulfuric acid, be careful  
not to let the battery electrolyte come in contact with your  
body or clothing.  
„ Always check the battery terminals periodically to ensure  
that they are in good condition.  
REAR VIEW  
FRONT VIEW  
Figure 36. Adding Hydraulic Oil  
„ Always wear eye protection and rubber gloves, since the  
battery contains sulfuric acid which burns skin and eats  
through clothing.In case of contact, flush thoroughly with  
water and contact a doctor immediately.  
CauTiOn  
Make sure hydraulic oil is at a normal safe operating  
level. dO nOT over fill. Over filling (excessive oil) will  
cause excess oil to blow out of breather plug.  
„ Use wire brush or sand paper to clean the battery  
terminals.  
3. Loosen bleeder plug located at top of hydraulic cylinder  
on side of vibrator (Figure 37). Air remaining in the  
circuit will be forced out of the bleeder plug. Once all  
air has been purged from the hydraulic system, tighten  
bleeder plug securely  
„ Always check battery for cracks or any other damage.  
If white pattern appears inside the battery or paste has  
accumulated at the bottom, replace the battery.  
„ If the compactor will not be in operation for a long period  
of time, store in cool dry place and check the battery  
charge level every month to maintain the performance  
of the battery.  
4. Reinsert oil plug into hydraulic oil tank and tighten  
securely. Reinstall breather cap.  
„ Check the battery regularly and make sure that each  
electrolyte level is to the bottom of the vent well (Figure 38).  
If necessary add only distilled water in a well-ventilated area.  
NOTICE  
The bleeder plug should only be loosened, but not  
removed.  
BLEEDER  
PLUG  
HYDRAULIC  
CYLINDER  
Figure 37. Bleeder Plug  
Figure 38. Battery Electrolyte Levels  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BaTTeRY ChaRging  
BaTTeRY CaBLe COnneCTiOn (Option)  
„ dO nOT charge battery with the battery cables  
connected to the compactor.The diodes will be damage  
by the high voltage.  
1. Take off the battery cover by removing the M6 nuts that  
secure the battery holder to the cover.  
2. When removing battery cables, disconnect the ground  
side (normally negative) first (Figure 39).  
„ Batteries generate hydrogen gas which  
can be highly explosive. dO nOT smoke  
or allow flames or sparks near the battery,  
especially during charging of the battery.  
3. When installing battery cable connect the ground side  
(normally negative) last.  
„ Charge the battery in a open air environment (plenty of  
ventilation).  
„ Before charging , remove the cap from each cell of the  
battery.  
„ Connect the positive (+) lead of the charger to the  
positive (+) terminal of the battery and the negative (-)  
lead of the charger to the negative (-) terminal of the  
battery. dO nOT reverse the polarity when charging.  
Reverse polarity will damage the charger rectifier or  
the battery.  
Figure 39. Removing Battery Cover  
CheCKing FueL FiLTeR  
„ Battery fluid will be lost through continuous charging  
and discharging.  
1. Clean the fuel filter every 3 months or 200 hours.  
2. Replace fuel filter every 6 months or 400 hours.  
„ Discontinue charging if the electrolyte temperature  
exceeds 117° F (45° C).  
3. To clean the fuel filter, loosen the nuts (Figure 40) of  
the fuel cock and pull out the filter from the F.O. tank  
filler port.Wash the filter thoroughly with diesel fuel oil.  
NOTICE  
During summer much more battery fluid is lost than in  
winter. Before starting, check battery electrolyte levels  
and replenish with distilled water to the upper mark on  
the battery.  
4. Reinstall fuel filter and connect all associated hardware  
DRAIN  
PLUG  
NUTS  
page 28 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
Figure 40. Fuel Filter  
Figure 42. Recoil Starter Grip  
5. For electric start type compactors, turn the engine for  
2 or 3 seconds with the decompression lever set in the  
non-decompression position, and the starter key at the  
START position. dO nOT start the engine.  
LOngTeRm sTORage  
When storing your compactor for long periods do the  
following:  
1. Run the engine at idle speed for 3-5 minutes.  
6. Pull the decompression lever up. Pull the recoil starter  
grip slowly. STOP when it feels tight. This closes the  
intake and exhaust valves (compression position) , and  
helps prevents ruts from forming.  
2. Stop the engine. Drain the engine crankcase oil while  
the engine is still warm. Fill Engine crankcase with  
fresh oil.  
7. Wipe any oil or dirt that may have accumulated on the  
compactor.  
3. Remove the rubber plug (Figure 41) on the rocker  
arm cover and add about 2 cc of lube oil. Reinstall  
rubber plug.  
8. Store compactor in a cool dry place out of the reach  
of children or unauthorized personnel  
RUBBER  
PLUG  
DECOMPRESSION  
LEVER  
Figure 41. Decompression Lever  
4. For recoil type compactors, push the decompression  
down (non-decompression position) and hold it while  
you pull the recoil starter grip (Figure 42) rope 2 or 3  
times. dO nOT start the engine.  
STARTER  
GRIP  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ExplANATION Of CODE IN REMARkS COluMN  
The following section explains the different symbols and  
QTY. Column  
remarks used in the Parts section of this manual. Use the  
help numbers found on the back page of the manual if there  
are any questions.  
numbers used — Item quantity can be indicated by a  
number, a blank entry, or A/R.  
A/R (As Required) is generally used for hoses or other  
parts that are sold in bulk and cut to length.  
NOTICE  
The contents and part numbers listed in the parts  
section are subject to change withoutnotice.Multiquip  
does not guarantee the availability of the parts listed.  
A blank entry generally indicates that the item is not sold  
separately.Other entries will be clarified in the “Remarks”  
Column.  
sampLe paRTs LisT  
REMARKS Column  
nO. paRT nO. paRT name  
QTY. REMARKS  
Some of the most common notes found in the “Remarks”  
Column are listed below. Other additional notes needed  
to describe the item can also be shown.  
1
2%  
12345  
BOLT .....................1 .....INCLUDES ITEMS W/%  
WASHER, 1/4 IN. ..........NOT SOLD SEPARATELY  
WASHER, 3/8 IN. ..1 .....MQ-45T ONLY  
2% 12347  
3
4
12348  
12349  
HOSE ..................A/R ...MAKE LOCALLY  
BEARING ..............1 .....S/N 2345B AND ABOVE  
assembly/Kit — All items on the parts list with the  
same unique symbol will be included when this item is  
purchased.  
nO. Column  
Indicated by:  
unique symbols — All items with same unique symbol  
(@, #, +, %, or >) in the number column belong to the  
same assembly or kit, which is indicated by a note in the  
“Remarks” column.  
“INCLUDES ITEMS W/(unique symbol)”  
serial number Break — Used to list an effective serial  
number range where a particular part is used.  
duplicate item numbers — Duplicate numbers indicate  
multiple part numbers, which are in effect for the same  
general item, such as different size saw blade guards in  
use or a part that has been updated on newer versions  
of the same machine.  
Indicated by:  
“S/N XXXXX AND BELOW”  
“S/N XXXX AND ABOVE”  
“S/N XXXX TO S/N XXX”  
specific model number use — Indicates that the part  
is used only with the specific model number or model  
number variant listed. It can also be used to show a  
part is NOT used on a specific model or model number  
variant.  
NOTICE  
When ordering a part that has more than one item  
number listed, check the remarks column for help in  
determining the proper part to order.  
Indicated by:  
paRT nO. Column  
“XXXXX ONLY”  
“NOT USED ON XXXX”  
numbers used — Part numbers can be indicated by a  
number, a blank entry, or TBD.  
“make/Obtain Locally” — Indicates that the part can  
be purchased at any hardware shop or made out of  
available items.Examples include battery cables, shims,  
and certain washers and nuts.  
TBD (To Be Determined) is generally used to show a  
part that has not been assigned a formal part number  
at the time of publication.  
A blank entry generally indicates that the item is not sold  
separately or is not sold by Multiquip. Other entries will  
be clarified in the “Remarks” Column.  
“not sold separately”— Indicates that an item cannot  
be purchased as a separate item and is either part of an  
assembly/kit that can be purchased, or is not available  
for sale through Multiquip.  
page 30 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SuGGESTED SpARE pARTS  
MVH306DS2/DSCPAS W/YANMAR L70V6 DIESEL ENGINE  
1 to 3 Units  
Qty.  
1............956100054............THROTTLE WIRE  
p/n  
description  
2............070200373............V-BELT  
3............11425012580........ELEMENT W/ PRE-FILTER  
1............16081076630........STARTER ROPE  
2............11425055121........FUEL FILTER W/GASKET  
1............11428855010........CAP, FUEL TANK W/GASKET  
1............11425035110........LUBE OIL STRAINER  
1............11425055100........FUEL STRAINER  
1............955300680............IGNITION SWITCH W/ KEY  
3............955000010............KEY, IGNITION SWITCH  
NOTICE  
Part numbers on this Suggested Spare Parts list may  
supersede/replace the part numbers shown in the  
following parts lists.  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NAMEplATES AND DECAlS  
page 32 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NAMEplATES AND DECAlS  
nO.  
1
2
3
4
5
6
7
8
paRT nO.  
920201950  
920105070  
920110370  
920209620  
920211090  
920204580  
920203330  
920211060  
920213920  
920216620  
920201580  
920211010  
920106760  
920214100  
920216610  
paRT name  
DECAL: OIL SAE 10W-30  
QTY.  
REMARKS  
1
DECAL: MIKASA LOGO....................................1................ELECT. START MODEL ONLY  
DECAL: MODEL LOGO MVH-306  
DECAL: CAUTION  
DECAL: SHELL TELLUS OIL 32  
DECAL: FULL THROTTLE  
DECAL: EAR PROTECTION  
DECAL: CAUTION (TRAVEL LEVER)  
DECAL: SERIAL NO. ........................................1................CONTACT MQ PARTS DEPT.  
DECAL: SERIAL NO. (PAS)...............................1................CONTACT MQ PARTS DEPT.  
1
1
1
1
1
1
9
9
10  
11  
12  
14  
15  
DECAL: MQ LOGO  
1
1
1
1
1
DECAL: V-BELT HDPF-5370  
DECAL: STOP-RUN-START  
DECAL: E/G FIRE WARNING  
DECAL: CAUTION (FOR WASHING)  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIbRATING plATE ASSY.  
page 34 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIbRATING plATE ASSY.  
nO.  
1
2
3
4
5
6
7
8
paRT nO.  
464117840  
464460660  
953402930  
953400270  
953405260  
939010260  
020316130  
030216400  
001221635  
001221830  
58407  
030216400  
939010010  
020310080  
031110160  
030210250  
464343730  
011008015  
030208200  
52993  
paRT name  
VIBRATING PLATE  
DRAIN PLUG  
COPPER PACKING 19X30X1  
PLUG 1/4X14 10L  
PACKING 1/4 (CU)  
SHOCK ABSORBER 110X60H  
NUT M16  
QTY.  
REMARKS  
1
1
1
1
1
4
4
4
4
8
WASHER, LOCK M16  
BOLT 16X35 T  
BOLT 18X30 T  
9
10  
11  
12  
15  
16  
17  
18  
19  
20  
21  
31  
32  
33  
WASHER, LOCK M18 .......................................8................REPLACES P/N 030218460  
WASHER, LOCK M16  
SHOCK ABSORBER, STOPPER 45  
NUT M10  
WASHER, FLAT M10  
WASHER, LOCK M10  
COVER, VIBRATING PLATE  
BOLT 8X15 T .....................................................8................REPLACES P/N 001220815  
WASHER, LOCK M8  
EXTENSION PLATE .........................................2................REPLACES P/N 456210690  
BOLT 18X50 T ...................................................8................REPLACES P/N 001221850  
WASHER, LOCK M18 .......................................8................REPLACES P/N 030218460  
4
4
4
4
4
2
8
012218050  
58407  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bASE AND ENGINE ASSY.  
page 36 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bASE AND ENGINE ASSY.  
nO.  
1
2
3
4
5
6
7
8
paRT nO.  
464117850  
914410026  
012210040  
030210250  
031110160  
464216560  
011208025  
030208200  
0401450080  
464343670  
464457360  
456343340  
951406790  
952400690  
011208030  
030208200  
464216640  
092006010  
464343660  
464216590  
001521050  
464117920  
456449950  
011208030  
030208200  
0401450080  
022710809  
paRT name  
BASE  
QTY.  
REMARKS  
1
ENGINE ASSY. L70V6 (YANMAR) 1  
BOLT 10X40 T ...................................................4................REPLACES P/N 001221040  
WASHER, LOCK M10  
WASHER, FLAT M10  
BELT COVER (IN)  
BOLT 8X25 T .....................................................4................REPLACES P/N 001220825  
WASHER, LOCK M8  
WASHER, FLAT M8 ..........................................4................REPLACES P/N 031108160  
DUST-PROOF SPONGE (IN)  
SPACER/MVH-306  
CLUTCH ASSY./CHM03/W.FAN  
KEY 7X7X36 RR ...............................................1................REPLACES P/N 22512070360  
WASHER 9X35X4.5  
BOLT 8X30 T .....................................................1................REPLACES P/N 001220830  
WASHER, LOCK M8  
DUST-PROOF COVER  
FLAT HEAD SCREW 6X10  
DUST-PROOF SPONGE (OUT)  
BELT COVER (OUT)  
SOCKET HEAD BOLT 10X50 T  
RUBBER COVER (GUARD FRAME)  
PLATE, COVER  
BOLT 8X30 T .....................................................3................REPLACES P/N 001220830  
WASHER, LOCK M8  
WASHER, FLAT M8 ..........................................3................REPLACES P/N 031108160  
NYLON NUT M8  
4
4
1
4
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
35  
36  
37  
38  
39  
40  
1
1
1
1
1
1
3
1
1
4
1
1
3
3
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bASE AND ENGINE ASSY. (CONTINuED)  
page 38 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bASE AND ENGINE ASSY. (CONTINuED)  
nO.  
41  
42  
43  
44  
45  
46  
47  
48  
49  
51  
52  
53  
59  
60  
61  
62  
63  
64  
65  
66  
70  
71  
72  
paRT nO.  
2556390111  
2556380103  
0091720000  
0211140020  
R0401140030  
464457380  
014208020  
030208200  
454010020  
464118780  
012214030  
030214350  
459455560  
459010110  
070200373  
459000020  
2067550101  
58151  
paRT name  
QTY.  
REMARKS  
UNION TIP, DRAIN ...........................................1................REPLACES P/N 459010060  
DRAIN HOSE ....................................................1................REPLACES P/N 459010070  
HOSE BAND .....................................................2................REPLACES P/N 459010090  
GASKET (OIL DRAIN) ......................................2................REPLACES P/N 459010080  
PLUG ................................................................1................REPLACES P/N 459010100  
DRAIN JOINT  
BOLT 8X20 T .....................................................1................REPLACES P/N 001220820  
WASHER, LOCK M8  
CLAMP TC-100  
GUARD HOOK  
1
1
1
1
BOLT 14X30 T ...................................................4................REPLACES P/N 001221430  
WASHER, LOCK M14  
UNION, OIL DRAIN  
SEAL WASHER 16S  
V-BELT  
4
1
1
1
1
RETURN SPRING  
CLAMP CP. .......................................................1................REPLACES P/N 151010680  
WASHER, FLAT M5 ..........................................1................REPLACES P/N 031105080  
NUT M6, H=4.2  
NUT M6 (SPECIAL-L10)  
CLIP D6 (FOR M10)  
020406040  
959406800  
959407260  
012210015  
030210250  
1
1
1
BOLT 10X15 T ...................................................1................REPLACES P/N 001221015  
WASHER, LOCK M10  
1
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIbRATOR ASSY.  
page 40 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIbRATOR ASSY.  
nO.  
A
1#  
2
3
4
5#  
6#  
8#  
9#  
paRT nO.  
464910020  
464117880  
001221470  
001221450  
030214350  
047920120  
457212410  
951405370  
456327150  
080200550  
060105030  
951404970  
464343700  
009120301  
456337670  
009120302  
456337380  
456010010  
464343720  
040306911  
953010030  
042506000  
0080000010  
455435051  
455010070  
080100260  
456327130  
456210636  
050101050  
0105091025  
030210250  
011008015  
953404600  
455010020  
031110160  
952405470  
464343710  
464457370  
012012030  
030212300  
464216600  
001520852  
paRT name  
VIBRATING ASSY..............................................1................INCLUDES ITEMS W/ #  
QTY.  
REMARKS  
VIBRATING CASE  
BOLT 14X150 T  
BOLT 14X50 T  
WASHER, LOCK M14  
ROLLER BEARING NJ310EMC4  
ROTARY SHAFT, DRIVE  
KEY 15X10X39 RR  
GEAR, DRIVE  
STOP RING S-55  
OIL SEAL SB-50729  
KEY 12X8X30 R  
ECCENTRIC ROTATOR  
SOCKET HEAD BOLT 16X40 T  
ROTARY SHAFT, DRIVEN  
SOCKET HEAD BOLT 16X30 T  
PISTON ROD  
1
6
4
10  
4
1
1
1
2
1
1
4
2
1
2
1
1
1
2
1
2
10#  
11#  
12#  
13#  
14#  
15#  
16#  
17#  
18#  
19#  
20#  
21#  
25#  
26#  
27#  
28#  
29#  
30#  
31#  
33#  
34#  
35#  
36#  
37#  
38#  
39#  
43#  
46#  
47#  
48#  
49#  
51  
KNOCK PIN 10X70  
GEAR (DRIVEN)  
BEARING 6911  
SEAL CAP/SC72-8N  
BEARING 6000ZZSG  
STOP RING S-10 ..............................................1................REPLACES P/N 080200100  
PISTON, 22.4D  
1
1
1
1
1
2
PACKING USH-22.4X30X5  
STOP RING R-26  
BEARING COVER  
CYLINDER (L)/(AC)  
O-RING G-105  
BOLT 10X25 T ...................................................8................REPLACES P/N 001221025  
WASHER, LOCK M10  
BOLT 8X12 T .....................................................1................REPLACES P/N 001220812  
8
COPPER PACKING 8X16X2  
ELBOW 45 DEG. 15-0404  
WASHER, FLAT M10  
SHIM 90X110X0.5  
PULLEY  
1
1
8
2
1
1
WASHER  
BOLT 12X30 T ...................................................1................REPLACES P/N 001221230  
WASHER, LOCK M12  
BELT COVER (LOWER)  
SOCKET HEAD BOLT 8X60 T  
1
1
5
52  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROl HANDlE ASSY.  
page 42 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROl HANDlE ASSY.  
nO.  
1
2
3
4
5
7
8
9
paRT nO.  
464343680  
456336420  
012212035  
030212300  
031112230  
456336400  
456449940  
456449930  
001221681  
032124400  
025306016  
0401450160  
020316130  
020416100  
455434950  
455010030  
939010060  
020310080  
020412070  
022411635  
954404230  
011206020  
030206150  
031106100  
020106050  
501402870  
501402880  
959403460  
020310080  
456449980  
953405260  
031110160  
464343690  
0105050616  
030206150  
031106100  
464457710  
464457720  
paRT name  
HANDLE BRACKET  
QTY.  
REMARKS  
1
HANDLE BRACKET (R)  
BOLT 12X35 T ...................................................4................REPLACES P/N 001221235  
1
WASHER, LOCK M12  
WASHER, FLAT M12  
RUBBER COUPLING  
SHOCK ABSORBER  
RUBBER PLATE  
BOLT 16X250 T  
CONICAL SPRING WASHER M24  
SPRING PIN 6X16 ............................................2................REPLACES P/N 025406016  
WASHER, FLAT M16 ........................................2................REPLACES P/N 031116260  
4
4
2
2
2
1
2
10  
11  
12  
13  
14  
15  
18  
19  
20  
21  
22  
23  
25  
26  
27  
28  
29  
34  
35  
36  
37  
38  
39  
40  
43  
44  
45  
46  
47  
48  
NUT M16  
1
1
1
1
1
NUT M16, H=10  
SPINDLE  
KNOB  
SHOCK ABSORBER  
NUT M10, H=6 ..................................................1................REPLACES P/N 020410060  
NUT M12, H=7  
WING NUT M16  
CLAMP SA120-18  
1
1
1
BOLT 6X20 T .....................................................1................REPLACES P/N 001220620  
WASHER, LOCK M6  
WASHER, FLAT M6  
1
1
NUT M6 .............................................................1................REPLACES P/N 020306050  
HANDLE STOPPER  
SPRING/HANDLE (1.4X18X44)  
BALL GRIP 32D-M10  
NUT M10, H=6 ..................................................1................REPLACES P/N 020410060  
RUBBER PACKING 9D-20D-5T  
PACKING 1/4 (CU)  
1
1
1
1
1
1
1
WASHER, FLAT M10  
HANDLE COVER  
BOLT 6X15 T .....................................................6................REPLACES P/N 001220615  
WASHER, LOCK M6  
WASHER, FLAT M6  
PACKING A, HANDLE COVER  
PACKING B, HANDLE COVER  
6
6
1
1
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROl HANDlE ASSY. (CONTINuED)  
page 44 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROl HANDlE ASSY. (CONTINuED)  
nO.  
61  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
93  
94  
95  
96  
99  
101  
103  
104  
104  
paRT nO.  
464117890  
464216630  
464457400  
012010030  
030210250  
464216620  
030210250  
031110160  
020310080  
011208025  
030208200  
464457340  
959403840  
464457420  
464457350  
014208020  
0401450160  
458450660  
033910080  
464457440  
464010010  
011606025  
020106050  
464010020  
001520520  
58151  
paRT name  
QTY.  
REMARKS  
COLUMN, HANDLE  
TRAVEL LEVER  
HANDLE BOSS  
1
1
1
BOLT 10X30 T ...................................................2................REPLACES P/N 001221030  
WASHER, LOCK M10  
HANDLE W/GRIP RUBBER  
WASHER, LOCK M10  
WASHER, FLAT M10  
NUT M10  
2
1
2
2
2
BOLT 8X25 T .....................................................2................REPLACES P/N 001220825  
WASHER, LOCK M8  
THROTTLE LEVER  
BAR GRIP I.D. 12 MM  
COVER, THROTTLE  
ARM, THROTTLE  
SOCKET HEAD BOLT 8X20 T ..........................1................REPLACES P/N 001520820  
WASHER, FLAT M16 ........................................1................REPLACES P/N 031116260  
WASHER 16.4-35-0.6  
CONICAL SW 16.3 X 31.5 X 1.2  
STEEL BALL D6 (SUJ)  
DRY BUSHING/ LBF-1620  
BOLT 6X25 T .....................................................2................REPLACES P/N 001220625  
NUT M6 .............................................................2................REPLACES P/N 020306050  
ROD END M5  
SOCKET HEAD BOLT 5X20 T  
WASHER, FLAT M5 ..........................................1................REPLACES P/N 031105080  
2
1
1
1
1
2
3
1
1
1
1
020305040  
954002270  
956100054  
454010020  
959021815  
959021810  
NUT M5  
1
1
1
1
1
OIL HOSE W/SPRING 1/4 X 920  
THROTTLE WIRE  
CLAMP TC-100  
SPIRAL TUBE 6D-330L  
SPIRAL TUBE KEP6/ L=500 ............................1................REPLACES P/N 959021810  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HAND puMp ASSY.  
page 46 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HAND puMp ASSY.  
nO.  
B%  
C%  
2%  
3%  
4%  
9%  
paRT nO.  
464910040  
464910080  
464010040  
464010050  
464010060  
464010070  
paRT name  
ACCUMLATOR  
QTY.  
REMARKS  
1
O-RING DUST, SEAL, SET ...............................1................ INCLUDES ITEMS W/#  
CONTROL SHAFT  
BUSH  
CAM  
STOPPER  
SOCKET HEAD SCREW 5X5 T  
PLUG  
PIN,STOPPER  
PLUG  
BREATHER  
SOCKET HEAD BOLT 6X20 T ..........................1................REPLACES P/N 001520620  
O-RING P-20  
O-RING P-22 ....................................................2................REPLACES P/N 050200220  
O-RING S-38  
O-RING P-18  
1
2
1
2
2
1
2
2
1
10% 099205005  
11% 464010080  
12% 464010090  
13% 464010100  
14% 458010080  
15% 014206020  
16#% 050200200  
17#% 050210220  
18#% 050300380  
2
1
1
19#  
050200180  
22% 464010111  
26#% 050300400  
27#% 050200150  
28#% 050100400  
50% 464010120  
51% 458451630  
52#% 069904010  
53#% 069901010  
81% 984010060  
82% 984010040  
83% 984010050  
ACCUMULATOR CASE.....................................1................S/N N2419 AND ABOVE  
O-RING S-40  
O-RING P-15  
O-RING G-40  
SPRING PLUG  
BREATHER CAP  
1
1
1
1
1
DUST SEAL SER-40 .........................................1................S/N N2419 AND ABOVE  
DUST SEAL SER-15  
1
1
1
1
S/N N2419 AND ABOVE  
SPRING COMPRESSION TOOL  
DISASSEMBLING TOOL A  
DISASSEMBLING TOOL B  
84  
464216721  
HAND PUMP ASSY. ..........................................1................INCLUDES ITEMS W/%  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bATTERY ASSY.  
page 48 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
bATTERY ASSY.  
nO.  
1
2
3
4
5
6
7
8
paRT nO.  
464457460  
464457470  
464216660  
456447590  
456447600  
012210020  
030210250  
955010090  
955300490  
955300470  
955300480  
955300460  
464021020  
464457410  
011208025  
030208200  
464457390  
022710809  
0401450080  
464343740  
paRT name  
QTY.  
REMARKS  
BATTERY CORD (-) 400L  
BATTERY CORD (+) 550L  
CRADLE, BATTERY  
1
1
1
1
2
RUBBER PLATE (E) 28X240X5  
RUBBER PLATE 50X240X10  
SOCKET HEAD BOLT 10X20 T ........................2................REPLACES P/N 001221020  
WASHER, LOCK M10  
BATTERY 55B24L  
BATTERY TERMINAL (-)  
TERMINAL COVER (-)  
BATTERY TERMINAL (+)  
TERMINAL COVER (+)  
COVER, BATTERY  
FIXED PLATE, BATTERY COVER  
BOLT 8X25 T .....................................................4................REPLACES P/N 001220825  
WASHER, LOCK M8  
BATTERY BOLT  
NYLON NUT M8  
2
1
1
1
1
1
1
2
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
4
2
2
WASHER, FLAT M8 ..........................................2................REPLACES P/N 031108160  
HOLDER, BATTERY  
1
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMpACTION ANAlYZING SYSTEM ASSY. (MVH3O6DSCpAS)  
24  
BATTERY CRADLE  
23  
25  
page 50 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMpACTION ANAlYZING SYSTEM ASSY. (MVH3O6DSCpAS)  
nO.  
1
2
3
4
5
6
7
8
paRT nO.  
465350490  
464350510  
009110062  
952404470  
030206150  
022710607  
464350500  
464464350  
H5HB051000  
030205130  
959021812  
464350390  
515450380  
464464520  
paRT name  
COMPACTION SENSOR PANEL  
PACKING,SENSOR  
SOCKET HEAD SCREW 6X20  
WASHER, FLAT M6...........................................4................REPLACES P/N 031106100  
WASHER, LOCK M6  
NYLON NUT M6  
ACCELERATION SENSOR ASSY. ....................1................INCLUDES ITEMS W/ #  
SENSOR HOLDER COVER  
SOCKET HEAD BOLT 5X10 T...........................2................REPLACES P/N 001520510  
WASHER, LOCK M5  
SPIRAL TUBE 6D-800L  
WIRE HARNESS, SENSOR  
WIRE HARNESS  
QTY.  
REMARKS  
1
1
4
4
4
1
9
10  
11#  
12  
13  
14  
2
1
1
1
FUSE HOLDER, SENSOR ................................1................INCLUDES ITEMS W/ %  
FUSE 2 AMP......................................................1................MVH306DSCPAS  
15% 464010140  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
506010070  
464022020  
001521030  
959408330  
030210250  
0105091025  
031110160  
464457410  
030208200  
011208025  
CLAMP TC-150  
7
COVER,BATTERY .............................................1................MVH306DSCPAS ONLY  
SOCKET HEAD BOLT 10X30 T  
WIRE CLIP,SENSOR  
WASHER, LOCK M10  
2
1
3
BOLT 10X25 T....................................................1................REPLACES P/N 001221025  
WASHER, FLAT M10  
FIXED PLATE, BATTERY COVER  
WASHER, LOCK M8  
1
2
4
BOLT 8X25 T .....................................................4................REPLACES P/N 001220825  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ElECTRIC DEVICE ASSY.  
page 52 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ElECTRIC DEVICE ASSY.  
nO.  
1
2
24  
26  
28  
30  
41  
paRT nO.  
464457460  
464457470  
464459260  
454010020  
955300400  
506010070  
955300680  
paRT name  
QTY.  
REMARKS  
BATTERY CORD (-) 400L  
BATTERY CORD (+) 550L  
WIRE CP  
1
1
1
3
1
1
CLAMP TC-100  
BUZZER (EBL)  
CLAMP TC-150  
IGNITION SWITCH ASSY..................................1................INCLUDES ITEMS W/ #  
41A# 955000010  
44 10519878570  
IGNITION KEY  
HARNESS (C), WIRE  
1
1
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — CYlINDER blOCk ASSY.  
page 54 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — CYlINDER blOCk ASSY.  
nO.  
1
5
paRT nO.  
paRT name  
QTY.  
REMARKS  
11421001010  
11439501330  
11435001380  
11429901800  
11429901830  
11425001841  
22312040080  
23875020000  
11429901600  
26226060182  
26226060222  
26366060002  
11435001412  
11421001460  
11435002100  
11429935150  
26106080352  
10542501690  
11469901760  
24311000180  
22190160002  
11429902030  
11435002113  
16011002220  
16011002220  
24162152116  
26106080122  
11435002200  
11435002210  
12125239450  
CYLINDER BLOCK ASSY.  
CYLINDER HEAD GASKET ASSY.  
O-RING  
1
1
1
1
1
1
2
1
2
1
2
3
1
11  
12  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
35$  
37  
38  
39  
40  
42#  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
SHIM SET  
COVER (FO PUMP)  
GASKET  
PIN 4X8 STRAIGHT  
PLUG PT 1/4 STEEL  
PIN, 8X12  
STUD M6X18 PLATED  
STUD M6X22 PLATED  
NUT M6  
CRANKCASE GASKET  
CRANKCASE COVER D ...................................1................INCLUDES ITEMS W/ $  
MAIN BEARING US=STD.  
L.O. INLET PIPE  
BOLT M 8X35 PLATED  
PLUG M16  
1
1
15  
2
OIL GAUGE CAP, W/LUB ..................................2................INCLUDES ITEMS W/ #  
O-RING  
SEAL WASHER 16S  
RETAINER  
BALL BEARING  
OIL SEAL  
OIL SEAL  
NEEDLE BEARING  
BOLT M8X12 PLATED  
MAIN BEARING US=0.25..................................1................UNDERSIZED PART  
MAIN BEARING US=0.50..................................1................UNDERSIZED PART  
2
2
1
1
1
1
1
1
OIL PRESSURE SENDER  
1
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — CYlINDER HEAD ASSY.  
page 56 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — CYlINDER HEAD ASSY.  
nO.  
1
2
3
7
paRT nO.  
paRT name  
QTY.  
REMARKS  
11421001200  
11421001210  
11421011020  
11421011100  
11421011110  
11421011120  
11421011180  
11421011930  
11421011250  
11421011260  
11421011280  
11421011650  
CYLINDER HEAD A BOLT  
CYLINDER HEAD B BOLT  
CYLINDER HEAD ASSY.  
INTAKE VALVE  
2
2
1
1
1
2
2
2
8
9
EXHAUST VALVE  
VALVE SPRING  
SPRING RETAINER  
COTTER ASSY.  
10  
11  
13  
14#  
15#  
16#  
SUPPORT ASSY. ROCKER ..............................1................INCLUDES ITEMS W/ #  
ROCKER ARM SUPPORT  
C TYPE RETAINING PIN  
1
2
INTAKE ARM ASSY. .........................................1................INCLUDES ITEMS W/ +  
18#+ 11429911240  
19#+ 26856060002  
ADJUSTING SCREW  
LOCK NUT 6  
1
1
20#  
11421011660  
EXHAUST ARM ASSY. .....................................1................INCLUDES ITEMS W/ $  
22#$ 11429911240  
23#$ 26856060002  
ADJUSTING SCREW  
LOCK NUT 6  
VALVE STEM SEAL  
NOZZLE GASKET  
NOZZLE SPACER  
VALVE CAP  
VALVE SPRING WASHER  
NOZZLE RETAINER  
SPRING PIN 4X8  
BOLT M6X40 PLATED  
STUD M6X55  
1
1
2
1
1
2
2
1
1
2
2
2
1
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
11435011340  
11477111461  
11429511470  
10501011490  
11429911600  
11421011900  
22351040008  
26106060402  
26226060552  
26366060002  
11421011310  
11421011950  
NUT M6  
BONNET GASKET  
BONNET HEAD ASSY.......................................1................INCLUDES ITEMS W/ %  
37% 11421003590  
40% 11429903640  
42% 22312030160  
DECOMP SHAFT ASSY.  
DECOMP SPRING  
PARALLEL PIN 3X16  
BOLT M6X55 PLATED  
1
1
1
1
45  
26106060552  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — AIR ClEANER ASSY.  
page 58 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — AIR ClEANER ASSY.  
nO.  
1
paRT nO.  
paRT name  
AIR CLEANER ASSY.........................................1................INCLUDES ITEMS W/#  
QTY.  
REMARKS  
11421012511  
11421012020  
11421012520  
11421012560  
11421012580  
11421012590  
11421012600  
11429912300  
11421012210  
26106060202  
26226060302  
2#  
3#  
4#  
6#  
7#  
10#  
11  
12  
13  
14  
AIR CLEANER BODY  
AIR CLEANER COVER  
WING NUT  
1
1
1
1
1
1
3
1
1
3
STUD BOLT  
ELEMENT ASSY.  
KNOCKING KNOB  
U-NUT  
AIR CLEANER GASKET  
BOLT M6X20 PLATED  
STUD M6X30  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — MufflER ASSY.  
page 60 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — MufflER ASSY.  
nO.  
15  
16  
22  
23  
24  
25  
26  
paRT nO.  
paRT name  
QTY.  
REMARKS  
11429913200  
11439913520  
26106060142  
26216080182  
26366080002  
11424913600  
11425213910  
MUFFLER GASKET  
MUFFLER ASSY.  
BOLT M6X14 PLATED  
STUD M8X18 PLATED  
NUT M8  
1
1
2
2
2
1
1
CLAMP  
EXHAUST DEFECTOR  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — CRANkSHAfT AND CAMSHAfT ASSY.  
page 62 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — CRANkSHAfT AND CAMSHAfT ASSY.  
nO.  
1
6
paRT nO.  
paRT name  
CAMSHAFT ASSY.  
TAPPET  
ROLLER TAPPET ASSY.  
PUSH ROD ASSY.  
CRANKSHAFT (D) ASSY.  
NUT  
QTY.  
REMARKS  
71421014580  
11421014200  
11421014300  
11421014400  
71421021740  
11429921220  
11439921590  
11436221600  
11429921550  
22512040120  
71421028510  
26106080202  
16031014550  
22512070360  
24101062030  
1
2
1
2
1
1
7
12  
13  
21  
22  
25#  
26  
27  
45  
62  
63  
64  
65  
FLYWHEEL (DE) ASSY......................................1................INCLUDES ITEM W/ #  
RING GEAR  
FLYWHEEL WASHER  
KEY 4X12  
BALANCER SHAFT ASSY.  
BOLT M 8X20 PLATED  
WASHER  
1
1
1
1
1
1
1
2
KEY 7X36 RR  
BEARING  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — pISTON ASSY.  
page 64 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — pISTON ASSY.  
nO.  
28  
28  
28  
30#  
30$  
paRT nO.  
paRT name  
QTY.  
REMARKS  
71421022720  
71421022620  
71421022580  
71487022502  
11487222140  
PISTON W/ RINGS STD....................................1................INCLUDES ITEMS W/#  
PISTON W/RINGS OS = 0.25 ...........................1................INCLUDES ITEMS W/$  
PISTON W/RINGS OS = 0.50 ...........................1................INCLUDES ITEMS W/%  
PISTON RINGS SET = STD.  
PISTON RING SET OS = 0.25  
PISTON RING SET OS = 0.50  
PISTON PIN  
1
1
1
1
2
30% 11487222150  
36  
37  
38  
11439922300  
22252000210  
71421023701  
CIRCLIP 21  
CONNECTING ROD ASSY................................1................INCLUDES ITEMS W/@  
41@ 11820023200  
42@ 11421023600  
ROD BOLT  
CRANK PIN BEARING STD.  
2
1
42  
42  
11421023610  
11421023620  
CRANK BEARING PIN U.S. = 0.25 ...................1................UNDERSIZED PART  
CRANK BEARING PIN U.S. = 0.50 ...................1................UNDERSIZED PART  
44@ 11438023910  
PISTON PIN BUSH  
1
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — lub OIl puMp AND GOVERNOR ASSY.  
page 66 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — lub OIl puMp AND GOVERNOR ASSY.  
nO.  
1
7
8
9
paRT nO.  
paRT name  
QTY.  
REMARKS  
11425032010  
11429932070  
11429932570  
22312030160  
26106060122  
11425035110  
24341000224  
26106060162  
11421061500  
22322030200  
22322030200  
71421061700  
11421061290  
11429961600  
11477061610  
11429961190  
11477161810  
11477161830  
11429561940  
11477166600  
11477166690  
11478061090  
22451060000  
11477061520  
11425266051  
18336066110  
11429966250  
11429966440  
10522566990  
26106060142  
26106060202  
26756060002  
11421066010  
11429966200  
11477161890  
LUB. OIL PUMP ASSY.  
LUB. OIL PUMP COVER  
O-RING COVER  
1
1
1
1
3
PARALLEL PIN 3X16  
BOLT M 6X12 PLATED  
LUBE OIL FILTER COMPLETE.........................1................INCLUDES ITEMS W/ $  
O-RING 1A S- 22.4  
BOLT M 6X16 PLATED  
LEVER ASSY. ...................................................1................INCLUDES ITEMS W/ #  
10  
11  
13$  
14  
15  
27#  
32#  
35  
36+  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
1
1
TAPER PIN 3X20  
TAPER PIN 3X20  
1
1
GOVERNOR ASSY. ..........................................1................NCLUDES ITEMS W/ +  
GOVERNOR WEIGHT ASSY.  
OIL SEAL  
THRUST WASHER  
GOVERNOR WASHER  
PLAIN WASHER 14  
PLATE  
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
NUT  
FUEL LIMITER ASSY.  
NUT M14  
LEAD  
WIRE 0.6  
NEEDLE BEARING  
REGULATOR HANDLE  
REGULATOR BRACKET  
RETURN SPRING  
ADJUSTING BOLT  
SCREW  
BOLT M 6X14 PLATED  
BOLT M 6X20 PLATED  
LOCK NUT M6 PLATED  
REGULATOR SPRING  
RETURN SPRING  
PROTECTOR COMPLETE................................1................INCLUDES ITEMS W/ %  
65% 11477161960  
66% 24311000180  
SPACER  
O-RING 1A P- 18.0  
1
1
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — COOlING AND STARTING DEVICE ASSY.  
page 68 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — COOlING AND STARTING DEVICE ASSY.  
nO.  
1
2
3
4
5
6
7
8
paRT nO.  
paRT name  
QTY.  
5
1
1
1
1
1
5
1
4
4
1
1
1
4
4
1
REMARKS  
11429945220  
11421045260  
11421045270  
11421045300  
11421045310  
11439945320  
11435045340  
11421045350  
26106060082  
26106060202  
26226060852  
26366060002  
11421045100  
11429945300  
11429945310  
11429945330  
11429945350  
11439976251  
11439976510  
11439976521  
11439976530  
11439976540  
11439976550  
11439976560  
11439976570  
11439976580  
11439976620  
11439976630  
11439976590  
26106060082  
26106060122  
TANK GROMMET  
SIDE COVER B (13)  
SIDE COVER A (13)  
TOP COVER, BLACK (13)  
DAMPER  
SEAL RUBBER  
CYLINDER COLLAR COVER  
TOP COVER SPACER  
BOLT M 6X 8 PLATED  
BOLT M 6X 20 PLATED  
BOLT STUD 6X85  
NUT M 6  
FAN CASE (SILVER) (17)  
CUSHION RUBBER  
FAN CASE COLLAR  
FAN CASE SEAL  
FAN CASE BOLT  
RECOIL STARTER (D) ASSY. ...........................1................  
STARTER CASE  
RECOIL REEL  
RATCHET  
SPIRAL SPRING  
RATCHET COVER  
SPRING  
RETURN SPRING  
SCREW  
STARTER KNOB  
STARTER ROPE  
STARTER PULLEY  
BOLT M 6X 8 PLATED  
BOLT M 6X 12 PLATED  
9
10  
11  
12  
13  
14  
15  
16  
17  
19  
20#  
21#  
22#  
23#  
24#  
25#  
26#  
27#  
28#  
29#  
30  
31  
32  
4
INCLUDES ITEMS W/ #  
1
1
1
1
1
1
1
1
1
1
1
4
3
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — fuEl INJECTION puMp ASSY.  
page 70 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — fuEl INJECTION puMp ASSY.  
nO.  
1
18  
paRT nO.  
paRT name  
QTY.  
REMARKS  
71424951400  
71421053100  
11421053000  
11421053080  
11421053330  
11421053120  
11421053130  
11421053140  
11421053410  
11421053420  
11421053430  
11421053440  
11421053450  
11421053460  
11421053470  
11421053480  
11421053490  
11421053500  
11421053510  
11421053520  
11421053530  
11421053540  
11421053550  
11421053560  
11421053570  
11421053580  
11421053590  
11421053600  
11421053610  
FUEL INJECTION PUMP ASSY. .......................1................INCLUDES ITEMS W/*  
FUEL INJECTOR...............................................1................INCLUDES ITEMS W/$  
19$  
21$  
23$  
24$  
25$  
26$  
27$  
27  
27  
27  
27  
27  
27  
27  
27  
27  
27  
27  
27  
27  
NOZZLE ASSY.  
NOZZLE NUT  
PIN  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
NOZZLE SPRING  
SPRING SEAT  
VALVE SPACER ASSY.  
SHIM (T=1.00)  
SHIM (T=1.05)  
SHIM (T=1.10)  
SHIM (T=1.15)  
SHIM (T=1.20)  
SHIM (T=1.25)  
SHIM (T=1.30)  
SHIM (T=1.35)  
SHIM (T=1.40)  
SHIM (T=1.45)  
SHIM (T=1.50)  
SHIM (T=1.55)  
SHIM (T=1.60)  
SHIM (T=1.65)  
SHIM (T=1.70)  
SHIM (T=1.75)  
SHIM (T=1.80)  
SHIM (T=1.85)  
SHIM (T=1.90)  
SHIM (T=1.95)  
SHIM (T=2.00)  
27  
27  
27  
27  
27  
27  
27  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — fuEl TANk AND fuEl lINE ASSY.  
SEE FUEL  
INJECTION ASSY.  
SEE FUEL  
INJECTION ASSY.  
page 72 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — fuEl TANk AND fuEl lINE ASSY.  
nO.  
1
3@  
4@  
5@  
paRT nO.  
paRT name  
FUEL TANK, BLACK..........................................1................INCLUDES ITEMS W/@  
QTY.  
REMARKS  
71424955020  
11429955080  
23414080000  
11428855041  
DRAIN PLUG  
PACKING 8  
1
1
FUEL TANK CAP ASSY. ....................................1................INCLUDES ITEMS W/+  
7@+ 11428855081  
CAP VALVE  
1
1
1
2
4
8
11425055100  
11435055150  
10385455220  
11425055201  
11423955120  
11425055130  
11421055210  
11421055230  
11424055300  
24341000150  
11421055810  
22117080000  
26106060162  
26106080452  
26366060002  
11478059060  
23080014000  
11423959300  
FILTER, FUEL  
PIPE GUAGE  
CLAMP  
10  
11  
12  
13  
14#  
15  
16  
17  
18$  
19  
20  
21  
22  
23  
25>  
26>  
27  
FUEL TANK DAMPER  
FUEL FILTER.....................................................1................INCLUDES ITEMS W/#  
GASKET  
FUEL TANK STAY A  
FUEL TANK STAY B  
1
1
1
FUEL COCK ASSY. ...........................................1................INCLUDES ITEMS W/ $  
O-RING 1A S- 15.0  
LIFTING BOLT  
WASHER 8  
BOLT M 6X 16 PLATED  
BOLT M 8X 45 PLATED  
NUT M6  
1
1
1
2
1
2
1
2
FUEL OIL PIPE  
CLAMP 14  
RETURN PIPE ASSY.........................................1................INCLUDES ITEMS W/%  
28% 12472259050  
29% 11465059060  
CLAMP 9  
FUEL RETURN PIPE  
CLAMP 8  
PROTECT TUBE  
RETAINER  
1
1
1
1
1
1
1
30  
12406659100  
31% 11465259310  
32% 12175059890  
33  
39  
11421059800  
11421059850  
FUEL INJECTION PIPE  
INJECTION PIPE SUPPORT  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — STARTING MOTOR AND DYNAMO ASSY.  
page 74 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — STARTING MOTOR AND DYNAMO ASSY.  
nO.  
1
paRT nO.  
paRT name  
STARTER...........................................................1................INCLUDES ITEMS W/ $  
QTY.  
REMARKS  
71436277011  
11438177110  
X2114811000  
X2114715500  
11438177130  
11438177140  
11437177160  
2 $  
3 $  
4 $  
5 $  
6 $  
7 $  
ARMATURE  
1
1
1
1
1
THRUST WASHER KIT  
PINION STOPPER SET  
FIELD COIL ASSY.  
REAR COVER  
BRUSH HOLDER ASSY.....................................1................INCLUDES ITEMS W/#  
8 $# 11437179040  
9 $# 11437179050  
10 $# 11437179060  
11 $ X211445508  
12 $ 11438177151  
13 $ 11437177170  
14 $ 11437177180  
BRUSH (-)  
BRUSH (+)  
BRUSH SPRING  
PINION ASSY.  
GEAR HOUSING ASSY.  
DUST COVER KIT  
SHIFT LEVER KIT  
MAGNET SWITCH  
THROUGH BOLT  
BOLT M6X37  
TERMINAL COVER  
BOLT M10X30 PLATED  
NUT M8  
STATOR ASSY.  
DYNAMO WHEEL  
CORD CLAMP  
BOLT M6X12 PLATED  
BOLT M6X20 PLATED  
SCREW M6X15  
HARNESS BRACKET  
SCREW M4X10  
2
1
4
1
1
1
1
1
2
2
1
2
1
1
1
1
1
3
3
1
2
15$  
12969877020  
16 $ 11926077260  
17 $ 11437179070  
18 $ 12125477810  
19  
20  
22  
23  
24  
25  
26  
27  
30  
31  
32  
26106100302  
26716080002  
11439978730  
11439978740  
16026078700  
26106060122  
26106060202  
26577060152  
11434077400  
26023040102  
11435177540  
WIRE HARNESS ..............................................1................INCLUDES ITEMS W/ %  
33% 29411200000  
CARTRIDGE FUSE 20A  
REGULATOR  
BOLT M6X18 PLATED  
BOLT M6X20 PLATED  
JOINT  
2
1
2
2
1
34  
35  
36  
37  
11434077710  
26106060182  
26106060202  
11435177520  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — TOOl, lAbEl, AND GASkET ASSY.  
page 76 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR l70V6 — TOOl, lAbEl, AND GASkET ASSY.  
nO.  
3
4
5
6
7
8
11  
paRT nO.  
paRT name  
AIR COOLED LABEL  
YANMAR LABEL  
CAUTION LABEL  
HOW TO START- E LABEL  
DIESEL LABEL  
DECOMPRESSION LABEL  
QTY.  
REMARKS  
11429907100  
11429907110  
11421007120  
11421007130  
11429907160  
11421007200  
11429992590  
1
1
1
1
1
1
TOOL ASSY. .....................................................1................INCLUDES ITEMS W/ %  
12% 11429992600  
13% 11429992710  
14% 11429992720  
15% 11429992730  
16% 11429992740  
TOOL BAG  
1
1
1
1
1
WRENCH, BOX  
WRENCH, BOX  
DRIVER  
FUEL FITTING  
17  
71421092600  
11439501330  
11435001380  
11435001412  
24311000180  
11425001841  
22190160002  
11435011340  
11477111461  
11421011310  
11421012210  
11429913200  
11429932570  
24341000100  
23414080000  
24341000224  
24341000150  
GASKET SET (NON- ASB)................................1................INCLUDES ITEMS W/ #  
18#  
24#  
25#  
26#  
27#  
28#  
29#  
30#  
31#  
32#  
33#  
34#  
35#  
36#  
37#  
38#  
CYLINDER HEAD GASKET ASSY.  
O-RING  
1
1
1
2
1
2
2
1
1
1
1
1
1
1
1
1
CRANK CASE GASKET  
O-RING  
GASKET  
WASHER SEAL 16S  
VALVE STEM SEAL  
NOZZLE GASKET  
BONNET GASKET  
AIR CLEANER GASKET  
MUFFLER GASKET  
O-RING COVER  
O-RING 1A S- 10.0  
PACKING 8  
O-RING 1A S- 22.4  
O-RING 1A S-15.0  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TERMS AND CONDITIONS Of SAlE — pARTS  
5. Parts must be in new and resalable  
condition, in the original Multiquip  
package (if any), and with Multiquip part  
numbers clearly marked.  
Multiquip reserves the right to quote and  
sell direct to Government agencies, and to  
Original Equipment Manufacturer accounts  
who use our products as integral parts of their  
own products.  
paYmenT TeRms  
Terms of payment for parts are net 30 days.  
FReighT pOLiCY  
6. The following items are not returnable:  
All parts orders will be shipped collect or  
prepaid with the charges added to the invoice.  
All shipments are F.O.B. point of origin.  
Multiquip’s responsibility ceases when a  
signed manifest has been obtained from the  
carrier, and any claim for shortage or damage  
must be settled between the consignee and  
the carrier.  
a. Obsolete parts. (If an item is in the  
price book and shows as being  
replaced by another item, it is  
obsolete.)  
speCiaL eXpediTing seRviCe  
A $35.00 surcharge will be added to the  
invoice for special handling including bus  
shipments, insured parcel post or in cases  
where Multiquip must personally deliver the  
parts to the carrier.  
b. Any parts with a limited shelf life  
(such as gaskets, seals, “O” rings,  
and other rubber parts) that were  
purchased more than six months  
prior to the return date.  
LimiTaTiOns OF seLLeR’s LiaBiLiTY  
minimum ORdeR  
Multiquip shall not be liable hereunder for  
damages in excess of the purchase price of  
the item with respect to which damages are  
claimed, and in no event shall Multiquip be  
liable for loss of profit or good will or for any  
other special, consequential or incidental  
damages.  
The minimum charge for orders from Multiquip  
is $15.00 net. Customers will be asked for  
instructions regarding handling of orders not  
meeting this requirement.  
c. Any line item with an extended  
dealer net price of less than  
$5.00.  
d. Special order items.  
ReTuRned gOOds pOLiCY  
Return shipments will be accepted and  
credit will be allowed, subject to the following  
provisions:  
e. Electrical components.  
f. Paint, chemicals, and lubricants.  
g. Decals and paper products.  
h. Items purchased in kits.  
LimiTaTiOn OF WaRRanTies  
No warranties, express or implied, are  
made in connection with the sale of parts or  
trade accessories nor as to any engine not  
manufactured by Multiquip. Such warranties  
made in connection with the sale of new,  
complete units are made exclusively by a  
statement of warranty packaged with such  
units, and Multiquip neither assumes nor  
authorizes any person to assume for it  
any other obligation or liability whatever in  
connection with the sale of its products. Apart  
from such written statement of warranty,  
there are no warranties, express, implied or  
statutory, which extend beyond the description  
of the products on the face hereof.  
1. A Returned Material Authorization  
must be approved by Multiquip prior to  
shipment.  
7. The sender will be notified of any material  
received that is not acceptable.  
8. Such material will be held for five  
working days from notification, pending  
instructions. If a reply is not received  
within five days, the material will be  
returned to the sender at his expense.  
2. To obtain a Return Material Authorization,  
a list must be provided to Multiquip  
Parts Sales that defines item numbers,  
quantities, and descriptions of the items  
to be returned.  
9. Credit on returned parts will be issued  
at dealer net price at time of the original  
purchase, less a 15% restocking  
charge.  
a. The parts numbers and descriptions  
must match the current parts price  
list.  
b. The list must be typed or computer  
generated.  
10. In cases where an item is accepted, for  
which the original purchase document  
can not be determined, the price will be  
based on the list price that was effective  
twelve months prior to the RMA date.  
c. The list must state the reason(s)  
for the return.  
Effective: February 22, 2006  
d. The list must reference the sales  
order(s) or invoice(s) under  
which the items were originally  
purchased.  
11. Credit issued will be applied to future  
purchases only.  
pRiCing and ReBaTes  
e. The list must include the name  
and phone number of the person  
requesting the RMA.  
Prices are subject to change without prior  
notice. Price changes are effective on a  
specific date and all orders received on or  
after that date will be billed at the revised price.  
Rebates for price declines and added charges  
for price increases will not be made for stock  
on hand at the time of any price change.  
3. AcopyoftheReturnMaterialAuthorization  
must accompany the return shipment.  
4. Freight is at the sender’s expense. All  
parts must be returned freight prepaid to  
Multiquip’s designated receiving point.  
page 78 — mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
mvh306ds2/dsCpas pLaTe COmpaCTOR • OpeRaTiOn and paRTs manuaL — Rev. #7 (02/04/14) — page 79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OperatiOn and parts Manual  
HERE’S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL  
NUMBER ON-HAND WHEN CALLING  
UNITED STATES  
Multiquip Corporate Office  
MQ Parts Department  
18910 Wilmington Ave.  
Carson, CA 90746  
Contact: [email protected]  
Tel. (800) 421-1244  
Fax (310) 537-3927  
800-427-1244  
310-537-3700  
Fax: 800-672-7877  
Fax: 310-637-3284  
Service Department  
Warranty Department  
800-421-1244  
310-537-3700  
Fax: 310-537-4259  
Fax: 310-943-2238  
800-421-1244  
310-537-3700  
Fax: 310-943-2249  
Technical Assistance  
800-478-1244  
UNITED KINGDOM  
CANADA  
Multiquip  
Multiquip (UK) Limited Head Office  
4110 Industriel Boul.  
Laval, Quebec, Canada H7L 6V3  
Contact: [email protected]  
Tel: (450) 625-2244  
Tel: (877) 963-4411  
Fax: (450) 625-8664  
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223  
Fax: 0161 339 3226  
Globe Lane,  
Dukinfield, Cheshire SK16 4UJ  
Contact: [email protected]  
© COPYRIGHT 2014, MULTIQUIP INC.  
Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property  
of their respective owners and used with permission.  
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.  
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in  
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published  
in this publication at any time without notice and without incurring any obligations.  
Your Local Dealer is:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Freezer KFN 14927 SD User Manual
Miele Washer Dryer W 2240 User Manual
Miller Electric Welding System 400P 500 X User Manual
Milwaukee Portable Multimedia Player SM102 User Manual
Mr Heater Fan MH24T User Manual
MTX Audio Stereo Amplifier 6304 User Manual
NAD CD Player T 751751 User Manual
Nilfisk Advance America Vacuum Cleaner Dry Vacuum Cleaner User Manual
Nortel Networks Answering Machine P0908524 User Manual
OWI Speaker IC6 710 User Manual