January 1997
Form: OM-175 104B
Effective With Serial No. KG191348
OWNER’S
MANUAL
Bobcat 225G
(Kohler-Powered)
CC/CV AC/DC Welding Generator For SMAW, FCAW, GMAW, GTAW Welding
Weld
Output
Range
Rated
Welding
Output
Maximum
Open-Circu
it Voltage
Welding
Mode
Auxiliary Power
Rating
Fuel Capacity
Engine
225 A, 25 V
100% Duty
Cycle
,
CC/AC
CC/DC
CV/DC
50 – 225 A
50 – 210 A
17 – 28 V
80
72
33
Kohler CH18
Air-Cooled, Two-Cylinder,
Four-Cycle, 18 HP
Gasoline Engine
210 A, 25 V
100% Duty
Cycle
,
Single-Phase,
8 kVA/kW, 70/35 A,
120/240 V AC, 60 Hz
8.5 gal (32 L) Tank
200 A, 20 V
100% Duty
Cycle
,
1997 MILLER Electric Mfg. Co.
cover_om 4/95 – Ref. ST-801 188-A
PRINTED IN USA
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 – SAFETY PRECAUTIONS FOR ARC WELDING
safety_rom1 4/95
1-1. Symbol Usage
Y
Marks a special safety message.
Means Warning! Watch Out! There are possible hazards with this
procedure! The possible hazards are shown in the adjoining symbols.
.
Means NOTE; not safety related.
This group of symbols means Warning! Watch Out! possible ELECTRIC SHOCK, MOVING
PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary
actions to avoid the hazards.
1-2. Arc Welding Hazards
WARNING
The symbols shown below are used throughout this manual to call attention to and identify possible hazards.
When you see the symbol, watch out, and follow the related instructions to avoid the hazard. The safety
information given below is only a summary of the more complete safety information found in the Safety
Standards listed in Section 1-5. Read and follow all Safety Standards.
Only qualified persons should install, operate, maintain, and repair this unit.
During operation, keep everybody, especially children, away.
terminal in disconnect box or that cord plug is connected to a
properly grounded receptacle outlet.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal
shocks or severe burns. The electrode and work
circuit is electrically live whenever the output is on.
The input power circuit and machine internal
circuits are also live when power is on. In
semiautomatic or automatic wire welding, the wire,
wire reel, drive roll housing, and all metal parts
touching the welding wire are electrically live.
Incorrectly installed or improperly grounded
equipment is a hazard.
7. When making input connections, attach proper grounding
conductor first – double-check connections.
8. Frequently inspect input power cord for damage or bare wiring –
replace cord immediately if damaged – bare wiring can kill.
9.
Turn off all equipment when not in use.
10. Do not use worn, damaged, undersized, or poorly spliced
cables.
1. Do not touch live electrical parts.
2. ear dry, hole-free insulating gloves and body protection.
3. Insulate yourself from work and ground using dry insulating
mats or covers big enough to prevent any physical contact with
the work or ground.
4. Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according
to OSHA 29 CFR 1910.147 (see Safety Standards).
5. Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
6. Always verify the supply ground – check and be sure that input
power cord ground wire is properly connected to ground
11. Do not drape cables over your body.
W
12. If earth grounding of the workpiece is required, ground it directly
with a separate cable – do not use work clamp or work cable.
13. Do not touch electrode if you are in contact with the work,
ground, or another electrode from a different machine.
14. Use only well-maintained equipment. Repair or replace
damaged parts at once. Maintain unit according to manual.
15. Wear a safety harness if working above floor level.
16. Keep all panels and covers securely in place.
17. Clamp work cable with good metal-to-metal contact to
workpiece or worktable as near the weld as practical.
ARC RAYS
ARC RAYS can burn eyes and skin;
NOISE can damage hearing; FLYING
SLAG OR SPARKS can injure eyes.
2. Wear a welding helmet fitted with a proper shade of filter to
protect your face and eyes when welding or watching (see ANSI
Z49.1 and Z87.1 listed in Safety Standards).
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Noise from some
processes can damage hearing. Chipping,
grinding, and welds cooling throw off pieces of
metal or slag.
3.
Wear approved safety glasses with side shields.
4. Use protective screens or barriers to protect others from flash
and glare; warn others not to watch the arc.
NOISE
5. Wear protective clothing made from durable, flame-resistant
material (wool and leather) and foot protection.
1. Use approved ear plugs or ear muffs if noise level is high.
5. Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained
watchperson nearby. Welding fumes and gases can displace air
and lower the oxygen level causing injury or death. Be sure the
breathing air is safe.
FUMES AND GASES can be hazardous
to your health.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
6. Do not weld in locations near degreasing, cleaning, or spraying
operations. The heat and rays of the arc can react with vapors to
form highly toxic and irritating gases.
1. Keep your head out of the fumes. Do not breathe the fumes.
2. If inside, ventilate the area and/or use exhaust at the arc to
remove welding fumes and gases.
7. Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the
weld area, the area is well ventilated, and if necessary, while
wearing an air-supplied respirator. The coatings and any metals
containing these elements can give off toxic fumes if welded.
3. If ventilation is poor, use an approved air-supplied respirator
.
4. Read the Material Safety Data Sheets (MSDSs) and the
manufacturer’s instruction for metals, consumables, coatings,
cleaners, and degreasers.
OM-175 104 Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Never drape a welding torch over a gas cylinder
5. Never allow a welding electrode to touch any cylinder
6. Never weld on a pressurized cylinder – explosion will result.
7. Use only correct shielding gas cylinders, regulators, hoses, and
fittings designed for the specific application; maintain them and
associated parts in good condition.
.
CYLINDERS can explode if damaged.
.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode.
Since gas cylinders are normally part of the welding
process, be sure to treat them carefully
.
1. Protect compressed gas cylinders from excessive heat,
mechanical shocks, slag, open flames, sparks, and arcs.
2. Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
3. Keep cylinders away from any welding or other electrical
circuits.
8. Turn face away from valve outlet when opening cylinder valve.
9. Keep protective cap in place over valve except when cylinder is
in use or connected for use.
10. Read and follow instructions on compressed gas cylinders,
associated equipment, and CGA publication P-1 listed in Safety
Standards.
6. Be aware that welding on a ceiling, floor, bulkhead, or partition
can cause fire on the hidden side.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks,
hot workpiece, and hot equipment can cause fires
and burns. Accidental contact of electrode to metal
objects can cause sparks, explosion, overheating,
or fire. Check and be sure the area is safe before
doing any welding.
7. Do not weld on closed containers such as tanks, drums, or
pipes, unless they are properly prepared according to AWS F4.1
(see Safety Standards).
8. Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock and fire hazards.
9. Do not use welder to thaw frozen pipes.
1. Protect yourself and others from flying sparks and hot metal.
2. Do not weld where flying sparks can strike flammable material.
10. Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
3. Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
11. Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
4. Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
12. Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
5. Watch for fire, and keep a fire extinguisher nearby
.
1-3. Engine Hazards
WARNING
1. Use equipment outside in open, well-ventilated areas.
2. If used in a closed area, vent engine exhaust outside and
away from any building air intakes.
ENGINE EXHAUST GASES can kill.
Engines produce harmful exhaust gases.
2. Do not add fuel while smoking or if unit is near any sparks or
open flames.
ENGINE FUEL can cause fire or
explosion.
Engine fuel is highly flammable.
3. Do not overfill tank – allow room for fuel to expand.
4. Do not spill fuel. If fuel is spilled, clean up before starting
engine.
1. Stop engine and let it cool off before checking or adding fuel.
3. Have only qualified people remove guards or covers for
MOVING PARTS can cause injury.
Moving parts, such as fans, rotors, and belts can
cut fingers and hands and catch loose clothing.
maintenance and troubleshooting as necessary
4. To prevent accidental starting during servicing, disconnect
negative (–) battery cable from battery
.
.
5. Keep hands, hair, loose clothing, and tools away from moving
parts.
6. Reinstall panels or guards and close doors when servicing is
finished and before starting engine.
1. Keep all doors, panels, covers, and guards closed and
securely in place.
2. Stop engine before installing or connecting unit.
1. Always wear a face shield when working on a battery
2. Stop engine before disconnecting or connecting battery
cables.
.
SPARKS can cause BATTERY GASES
TO EXPLODE; BATTERY ACID can
burn eyes and skin.
3. Do not allow tools to cause sparks when working on a battery
.
4. Do not use welder to charge batteries or jump start vehicles.
5. Observe correct polarity (+ and –) on batteries.
Batteries contain acid and generate explosive
gases.
1. If the engine is warm and checking is needed, follow steps 2
and 3.
STEAM AND PRESSURIZED HOT
COOLANT can burn face, eyes, and
skin.
2.
Wear safety glasses and gloves and put a rag over cap.
3. Turn cap slightly and let pressure escape slowly before
completely removing cap.
It is best to check coolant level when engine is
cold to avoid scalding.
OM-175 104 Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4. Additional Installation, Operation, And Maintenance Hazards
WARNING
MOVING PARTS can cause injury.
READ INSTRUCTIONS.
1. Before working of generator, remove spark plugs
or injectors to keep engine from kicking back or
starting.
2. Block flywheel so that it will not turn while working
on generator components.
1. Use only genuine MILLER replacement parts.
2. Reinstall injectors and bleed air from fuel system
according to engine manual.
DO NOT LET ENGINE EXHAUST SPARKS
CAUSE FIRE.
1. Use approved engine exhaust spark arrestor in
required areas – see applicable codes.
FLYING PIECES OF METAL or DIRT can
injure eyes.
1. Wear safety glasses with side shields or face
shield.
LOW VOLTAGE AND FREQUENCY CAN
DAMAGE electrical equipment such as
MOTORS.
1. Turn off or unplug equipment before starting or
stopping engine.
STATIC ELECTRICITY can damage parts
on circuit boards.
1. Put on grounded wrist strap BEFORE handling
boards or parts.
2. Use proper static-proof bags and boxes to store,
move, or ship PC boards.
OVERUSE can cause OVERHEATED
EQUIPMENT.
1. Allow cooling period.
MAGNETIC
CURRENTS can affect pacemaker
operation.
FIELDS
FROM
HIGH
2. Reduce current or reduce duty cycle before
starting to weld again.
1. Pacemaker wearers keep away.
2.
Wearers should consult their doctor before going
3. Follow rated duty cycle.
near arc welding, gouging, or spot welding
operations.
TILTING OF TRAILER can cause injury.
1. Use tongue jack or blocks to support weight.
2. Properly install welding generator onto trailer
HOT PARTS can cause severe burns.
1. .Allow cooling period before maintaining.
2. Wear protective gloves and clothing when working
on a hot engine.
according to instructions supplied with trailer
.
BATTERY ACID can BURN SKIN AND
EYES.
1. Do not tip.
FALLING EQUIPMENT can cause serious
personal injury and equipment damage.
1. Use lifting eye to lift unit only, NOT running gear,
gas cylinders, or any other accessories.
2. Replace damaged battery
.
2. Use equipment of adequate capacity to lift unit.
3. Flush eyes and skin immediately with water
.
1-5. Principal Safety Standards
Safety in Welding and Cutting, ANSI Standard Z49.1, from American
Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet
P-1, from Compressed Gas Association, 1235 Jefferson Davis
Highway, Suite 501, Arlington, VA 22202.
Safety and Health Standards, OSHA 29 CFR 1910, from
Superintendent of Documents, U.S. Government Printing Office,
Washington, D.C. 20402.
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale
Boulevard, Rexdale, Ontario, Canada M9W 1R3.
Recommended Safe Practices for the Preparation for Welding and
Cutting of Containers That Have Held Hazardous Substances,
American Welding Society Standard AWS F4.1, from American
Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126
Safe Practices For Occupation And Educational Eye And Face
Protection, ANSI Standard Z87.1, from American National Standards
Institute, 1430 Broadway, New York, NY 10018.
National Electrical Code, NFPA Standard 70, from National Fire
Protection Association, Batterymarch Park, Quincy, MA 02269.
Cutting And
Welding Processes, NFPA Standard 51B, from National
Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
1-6. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
To reduce magnetic fields in the workplace, use the following
procedures:
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around the body.
The following is a quotation from the General Conclusions Section of
the U.S. Congress, Office of Technology Assessment, Biological
Effects of Power Frequency Electric & Magnetic Fields – Background
Paper, OTA-BP-E-53 (Washington, DC: U.S. Government Printing
Office, May 1989): “. . . there is now a very large volume of scientific
findings based on experiments at the cellular level and from studies
with animals and people which clearly establish that low frequency
magnetic fields can interact with, and produce changes in, biological
systems. While most of this work is of very high quality, the results are
complex. Current scientific understanding does not yet allow us to
interpret the evidence in a single coherent framework. Even more
frustrating, it does not yet allow us to draw definite conclusions about
questions of possible risk or to offer clear science-based advice on
strategies to minimize or avoid potential risks.”
4. Keep welding power source and cables as far away as
practical.
5. Connect work clamp to workpiece as close to the weld as
possible.
About Pacemakers:
The above procedures are also recommended for pacemaker
wearers. Consult your doctor for complete information.
OM-175 104 Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2 – DEFINITIONS
2-1. Symbol Definitions
Fast
Fast/Slow
(Run/Idle)
Stop Engine
Slow (Idle)
Volts
(Run, Weld/Power)
Read Operator’s
Manual
Start Engine
Engine Oil
Amperes
A
V
Fuel
Battery (Engine)
Engine
Check Valve
Clearance
Do not switch
while welding
Engine Choke
Positive
W
ork Connection
Alternating Current
(AC)
Negative
Output
Gas Metal Arc
Shielded Metal Arc
W
elding Arc
Gas Tungsten Arc
elding (TIG)
W
elding (GMAW),
W
elding (SMAW),
(Electrode)
W
Wire
Stick
Protective Earth
(Ground)
Hours
Seconds
Time
h
s
Temperature
Circuit Breaker
OM-175 104 Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3 – INSTALLATION
3-1. Installing Welding Generator
Movement
Airflow Clearance
Location
18 in
(460 mm)
18 in
(460 mm)
18 in
(460 mm)
OR
OR
18 in
(460 mm)
18 in
(460 mm)
Grounding
1
2
3
Generator Base
3
Metal Vehicle Frame
1
GND/PE
4
Equipment Grounding
Terminal
4
Grounding Cable
OR
Use #10 AWG or larger insulated
copper wire.
Electrically bond generator frame to
vehicle frame by metal-to-metal
contact.
2
2
install1* 3/96 – Ref. ST-800 652 / Ref. ST-800 477-A / ST-158 936-A / S-0854
3-2. Dimensions, Weights, And Operating Angles
Dimensions
A
B
Height
Width
Depth
A
31 in (787 mm)
18-3/4 in (476 mm)
46 in (1164 mm)
18 in (457 mm)
C
Y
Y
Do not exceed operating angles while
running or engine damage will occur
.
Do not move or operate unit where it could
tip.
D
G
4 Holes
E
25°
F
B
16-1/2 in (419 mm)
3/4 in (19 mm)
25°
25°
25°
C
D
E
F
3-1/8 in (79 mm)
32-3/4 in (832 mm)
45-1/2 in (1156 mm)
13/32 in (10 mm) Dia.
angles_1 3/96
Weight
Engine End
Net: 567 lb (258 kg)
Ship: 608 lb (276 kg)
ST-800 426
G
OM-175 104 Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
3-3. Fuel Consumption
2.0
1.8
1.5
1.3
1.0
0.8
0.5
0.3
0.0
1.67
1.46
7.57
6.62
5.67
4.73
3.78
2.84
1.89
0.95
AUX POWER
3750 RPM
DC WELD
3750 RPM
1.25
1.04
AC WELD
3750 RPM
0.84
0.63
0.42
0.21
CV WELD
3750 RPM
IDLE
2200 RPM
0
0
25
50
75 100 125 150 175 200 225 250 275
WELD AMPERES AT 100% DUTY CYCLE
1.0
2.0 3.0 4.0
5.0 6.0 7.0 8.0 9.0 10.0 11.0
POWER KVA AT 100% DUTY CYCLE
Ref. SB-179 939
3-4. Engine Prestart Checks
Check all fluids daily. Engine must
be cold and on a level surface. Unit
is shipped with 10W30 engine oil.
1
Low Oil Pressure Shutdown
Switch
Engine stops if oil pressure gets
too low
.
Full
2
Anti-Icing Control
Use control to prevent carburetor
icing in cold weather
.
1/2 in
(13 mm)
2
Full
Below
Above
Gasoline
45°F
(7°C)
1
Ref. ST-801 188-A / Ref. ST-801 221
OM-175 104 Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5. Connecting The Battery
Y
Connect (–) cable last.
–
+
Tools Needed:
3/8, 1/2 in
Ref. ST-800 394-B / Ref. ST-178 079-A / Ref. S-0756-D
3-6. Weld Output Terminals And Selecting Cable Sizes
Y
ARC WELDING can cause Electromagnetic Interference.
To reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the
floor. Locate welding operation 100 meters from any sensitive electronic equipment. Be sure this welding machine is
installed and grounded according to this manual. If interference still occurs, the user must take extra measures such
as moving the welding machine, using shielded cables, using line filters, or shielding the work area.
Total Cable (Copper) Length In Weld Circuit Not Exceeding
150 ft
(45 m)
200 ft
(60 m)
250 ft
(70 m)
300 ft
350 ft
400 ft
100 ft (30 m) Or Less
10 – 60% 60 – 100%
(90 m) (105 m) (120 m)
Welding
Amperes
Weld Output Terminals
Duty
Cycle
Duty
Cycle
10 – 100% Duty Cycle
100
150
200
250
300
350
4
3
4
3
4
2
3
2
1/0
1
1/0
3/0
1/0
3/0
1
2/0
3
2
1
1/0
2/0
3/0
4/0
2/0
3/0
4/0
4/0
2
1
1/0
2/0
3/0
3/0
4/0
2-2/0
2-3/0
2-3/0
2-2/0
2-3/0
1
1/0
2/0
4/0
2-2/0
2-3/0
WORK ELECTRODE
1/0
2-2/0
2-4/0
ST-800 396-A
Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.
S-0007-D
OM-175 104 Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4 – OPERATING WELDING GENERATOR
4-1. Front Panel Controls
4
5
1
6
2
3
Ref. ST-178 079-A
1
Engine Control Switch
gine starts. Do not crank engine if engine is
Use switch to select weld amperage range
when Weld Process Selector switch is in
Stick/Tig position, or voltage range when
switch is in Wire position.
still turning. Set anti-icing control (see Sec
tion 3-4).
-
Use switch to start engine, select speed,
and stop engine. In Run/Idle position, en-
gine runs at idle speed at no load, and weld/
power speed under load. In Run position,
engine runs at weld/power speed.
To Stop: turn Engine Control switch to Off
position.
. For best arc starts, use lowest amper-
age range possible.
3
Weld Process Selector Switch
5
Fine Adjust Control
. Place switch in Run position to operate
Use switch to select type of weld output.
Use control to select weld amperage (Stick/
Tig) or voltage (Wire) within the range se-
lected by the Coarse Adjust switch. Control
may be adjusted while welding. Weld output
would be 110 A DC based on control set-
tings shown (50% of 70 to 150 A).
most GMAW equipment.
Use a positive (+) position for Direct Current
Electrode Positive (DCEP) and a negative
(–) position for Direct Current Electrode
Negative (DCEN). Use AC position for alter
nating current.
2
Engine Choke Control
Use control to change engine air-fuel mix.
-
To Start: pull out choke and turn Engine
Control switch to Start position. Release
switch and slowly push choke in when en-
4
Coarse Adjust Switch
6
Engine Hour Meter
OM-175 104 Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2. Duty Cycle
Duty cycle is the percentage of 10
minutes that unit can weld at rated
load without overheating.
Y
Exceeding duty cycle can
damage unit and void war-
ranty.
100% Duty Cycle at 225 Amperes AC, 210 Amperes CC/DC, 200 Amperes CV/DC
Continuous
Welding
SB-119 454-A
OM-175 104 Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 – OPERATING AUXILIARY EQUIPMENT
5-1. Standard Receptacles
. Auxiliary power decreases as
weld current increases.
Set Fine Adjust control R1 at
10 for full auxiliary power
.
1
120 V 15 A AC Receptacles
GFCI-2 And GFCI-3
GFCI-2 and GFCI-3 supply 60 Hz
single-phase power at weld/power
speed. Maximum output from each
receptacle is 2.4 kVA/kW (CSA:
1.8 kVA/kW).
3
4
If a ground fault is detected, Reset
button pops out and the circuit
opens to disconnect the faulty
equipment. Check for faulty tools,
1
cords, etc. connected to the recep
-
tacle. Press reset button to resume
operation.
2
. At least once a month, run en-
gine at weld/power speed and
press Test button to verify
GFCI is working properly
.
2
240 V 50 A AC Receptacle
RC1
RC1 supplies 60 Hz single-phase
power at weld/power speed. Maxi
mum output is 8 kVA/kW.
-
3
Circuit Breakers CB1 And
CB2
CB1 and CB2 protect RC1 from
overload. If CB1 or CB2 opens,
RC1 and one of the 120 volt recep
-
tacles does not work. 120 volts
may still be present at RC1.
4
Circuit Breakers CB3 And
CB4
CB3 and CB4 protect GFCI-2 and
GFCI-3 from overload. If CB3 or
CB4 opens, the receptacle does
not work.
. If a circuit breaker continues to
open, contact a Factory Au-
thorized Service Agent.
Total output of receptacles limited
to 8 kVA/kW. Example: If 20 A is
drawn from GFCI-2 and GFCI-3,
only 13 A is available at RC1:
2
=
x (120 V x 20 A) + (240 V x 13 A)
7.9 kVA/kW
Ref. ST-178 079-A
OM-175 104 Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2. Optional Auxiliary Power Receptacles
Y
If unit does not have GFCI
receptacles, use GFCI-pro-
tected extension cord.
. Auxiliary power decreases as
weld current increases.
Set Fine Adjust control R1 at
10 for full auxiliary power
.
1
Combined output of all receptacles
limited to 8 kVA/kW rating of the
generator.
120 Volt Receptacle Option
1
120 V 15 A AC Receptacles
RC2 And RC3
RC2 and RC3 supply 60 Hz single-
phase power at weld/power speed.
Maximum output from RC2 or RC3
is 2.4 kVA/kW (CSA: 1.8 kVA/kW).
Circuit breaker protection is the
same as standard receptacles.
South African And Australian
Receptacle Options
2
240 V 16 A AC South African
Receptacles RC1, RC2, And
RC3
4
3
240 V 15 A AC Australian
Receptacles RC1, RC2, And
RC3
Receptacles supply 60 Hz single-
phase power at weld/power speed.
5
Maximum output from each recep
tacle is 3.6 kVA/kW.
-
4
Circuit Breakers CB1, CB2,
CB3
CB1, CB2, and CB3 protect RC1,
RC2, and RC3 from overload. If a
circuit breaker opens, the recep-
tacle does not work. Press button
to reset breaker
.
2
5
Circuit Breaker CB4
CB4 protects all the receptacles
from overload. If CB4 opens, none
of the receptacles work.
. If a circuit breaker continues to
open, contact a Factory Au-
thorized Service Agent.
4
5
3
Ref. ST-172 786-B / Ref. ST-181 714
OM-175 104 Page 1
1
Download from Www.Somanuals.com. All Manuals Search And Download.
5-3. Wiring Optional 240 Volt Plug
The plug can be wired for a 240 V
,
2-wire load or a 120/240V, 3-wire
load. See circuit diagram.
1
Plug Wired For 120/240 V
3-Wire Load
,
7
When wired for 120 V loads, each
duplex receptacle shares a load
with one half of 240 V receptacle.
Current Available In Amperes
240 V
Receptacle*
Each 120 V Duplex
Receptacle
2
Plug Wired For 240 V, 2-Wire
Load
1
3
4
5
6
7
Neutral (Silver) Terminal
Load 1 (Brass)Terminal
Load 2 (Brass) Terminal
Ground (Green) Terminal
3
35
30
25
20
15
0
5
10
15
20
4
Amperes Available Using
120/240 V Plug
V x A = Watts
*One 240 V load or two 120 V loads.
120V
5
120V
240V
6
2
3
4
240V
6
5
Tools Needed:
ST-120 813-D
OM-175 104 Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6 – MAINTENANCE AND TROUBLESHOOTING
6-1. Routine Maintenance
Y
Stop engine before maintaining.
. See also Engine Manual and mainte-
nance label. Service engine more often
if used in severe conditions.
Recycle engine
fluids.
8 h
Check Fluid
Levels.
See Section 3-4.
Wipe Up
Spills.
20 h
Check And
Clean Optional
Spark Arrestor
Screen. See
Section 6-7.
Service Air
Cleaner Foam
Element. See
Section 6-3.
50 h
Clean And
ighten Weld
Terminals.
T
100 h
Check Air
Cleaner
Paper
Element. See
Section 6-3.
Change Oil. See
Check
Spark
Plugs.
Section 6-4 And
Maintenance
Label.
Clean Cooling
Clean And
Tighten
Battery
System.
See Engine
Manual.
Connections.
200 h
500 h
Change Oil
Filter. See Section
6-4 And
Maintenance
Label.
Replace
Replace
Unreadable
Labels.
Fuel Filter
See Section
6-4.
.
Repair Or Replace
Cracked Cables.
1000 h
Blow Out Or Vacuum Inside.
During Heavy Service,
Clean Monthly
OR
.
OM-175 104 Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2. Maintenance Label
KOHLER CH18 GAS ENGINE
Air Filter Service
Air Filter Element
.
.
. . . 100 hours or less – see
Owner’s Manual
. . . MILLER 067 272,
Kohler 4708303
See Engine Manual for complete engine care. Give
engine Specification and Serial Number when ordering
parts.
Air Filter Wrapper . . . . MILLER 067 273,
Kohler 2408302
Check
daily.
°C
°F
+100
+30
+20
+10
0
12 Volt Battery
.
. . . . . BCI Group 58
+
Cranking Performance at 0°F (-18°C) . . . . 430 Amps
min.
T
o Drain Oil:
+32
0
Push And
Turn CCW
-10
-20
-30
1/2 in. ID Hose
Pull
Engine RPM – No Load
Weld/Power . 3700
Idle . . . . . . . . . 2200
Recommended Oil
Oil Change . . . . . . . . 100 hours
Oil Filter Change . . . 200 hours
Oil Filter . . . . . . . . . . . MILLER 066 698, Kohler 1205001
.
. . API Service Classification SF-SG/CC-CD
.
.
Spark Plug Gap
.
. . . . 0.040 in. (1.02 mm)
.
Spark Plug . . . . . . . . Champion RC-12YC
.
Oil Capacity . . . . . . . . 1.75 qt (1.7 L) or 2 qt (1.9 L) with filter
change
Use only resistor spark plugs and wires.
Fuel Capacity
.
. . . . . . 8.5 gal (32.2 L)
Fuel Grade
Fuel Filter
.
. . . . . . . . Unleaded, 87 Octane min.
Spark Arrestor Inspection And Service . . . . . . . . . . .
20 operating hours - see Owner’s Manual
.
. . . . . . . . . MILLER 066 113,
Kohler 2505003
Gasoline
S-173 088
6-3. Servicing Air Cleaner
Y
Y
Stop engine.
1
2
Do not run engine without
air cleaner or with dirty ele-
ment.
1
Precleaner
Wash precleaner with soap and
water solution. Allow precleaner to
air dry completely
.
Spread 1 tablespoon SAE 30 oil
evenly into precleaner. Squeeze
out excess oil.
2
Element
Replace element if dirty or oily
.
oil
aircleaner3 6/96 – ST-156 852 / Ref. ST-178 079-A / S-0759
OM-175 104 Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4. Changing Engine Oil, Oil Filter, And Fuel Filter
Y
1
Stop engine and let cool.
Oil Drain Valve
1/2 ID x 12 in Hose
Oil Filter
2
3
4
Oil Fill Cap
5
Oil Dipstick
Change engine oil and filter ac-
cording to engine owner s manual.
’
Y
Close valve and valve cap
before adding oil and run-
ning engine.
Fill crankcase with new oil to full
mark on dipstick (see Section 6-2).
4
6
7
Fuel Filter
Fuel Line
Replace line if cracked or worn.
Install new filter. Wipe up any
spilled fuel.
Start engine, and check for fuel
leaks.
6
7
Y
Stop engine, tighten con-
nections as necessary, and
wipe up fuel.
3
2
5
1
Tools Needed:
Ref. ST-801 188-A / Ref. ST-801 221 / Ref. ST-178 079-A / ST-800 395 / S-0842
OM-175 104 Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5. Adjusting Engine Speed
After tuning engine, check engine
speeds with a tachometer (see
table). If necessary, adjust speeds
as follows:
2200 ± 50 rpm
Start engine and run until warm.
Turn Fine Adjust control to 10.
3700 ± 50 rpm
Idle Speed Adjustment
Move Engine Control switch to
Run/Idle position.
1
1
2
3
Throttle Solenoid
Mounting Screws
Idle Speed Screw
Loosen mounting screws. Adjust
solenoid position so engine runs at
idle speed. If necessary, back out
idle speed screw so solenoid can
be moved to correct position.
Tighten mounting screws. Be sure
5
2
4
solenoid linkage works smoothly
.
Turn idle speed screw for fine ad-
justments.
Weld/Power Speed Adjustment
Move Engine Control switch to Run
position.
4
Weld/Power Speed Adjust
ment Nut
-
5
Lock Nut
Loosen lock nut. Turn adjustment
nut until engine runs at weld/power
3
speed.
Tighten lock nut.
Y
Stop engine.
Top View
Tools Needed:
1/4, 3/8 in
Ref. ST-801 188-A / ST-801 209-A
OM-175 104 Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
6-6. Overload Protection
Y
Stop engine.
1
Fuse F1 (See Parts List)
F1 protects the generator excita-
tion circuit. If F1 opens, there will
be no/low weld and auxiliary power
output.
1
2
Fuse F6 (See Parts List)
F6 protects the engine wiring har-
ness. If F6 opens, the engine does
not crank.
Replace any open fuses. Reinstall
panel before operating unit.
. If any fuse continues to open,
contact Factory Authorized
Service Agent.
2
Tools Needed:
3/8 in
ST-801 226-A / Ref. ST-801 221
6-7. Inspecting And Cleaning Optional Spark Arrestor
Y
Stop engine and let cool.
1
Spark Arrestor Screen
Clean and inspect screen. Re-
place spark arrestor if screen wires
are broken or missing.
1
Tools Needed:
1/4 in
ST-801 206 / Ref. ST-801 221 / Ref. ST-172 782-A
OM-175 104 Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
6-8. Troubleshooting
A. Welding
Trouble
Remedy
No weld output.
Check control settings.
Check weld connections.
Check fuse F1 and replace if open (see Section 6-6).
Be sure all equipment is disconnected from receptacles when starting unit.
Have Factory Authorized Service Agent check brushes, slip rings, and integrated rectifier SR2.
Check plug PLG6 connection.
Low weld output.
Check fuse F1 and replace if open (see Section 6-6).
Check control settings.
Check and adjust engine speed (see Section 6-5).
Service air cleaner according to engine manual.
Have Factory Authorized Service Agent check brushes and slip rings.
Check control settings.
High weld output.
Check and adjust engine speed (see Section 6-5).
Check control settings.
Erratic weld output.
Tighten and clean connections to electrode and workpiece.
Use dry, properly-stored electrodes for SMAW and GTAW.
Remove excessive coils from weld cables.
Tighten and clean connections both inside and outside welding generator.
Check and adjust engine speed (see Section 6-5).
Have Factory Authorized Service Agent check brushes and slip rings.
B. Auxiliary Power
Trouble
Remedy
No output at auxiliary power recep
tacles.
-
Reset circuit breakers (see Sections 5-1 and 5-2).
Press receptacle Reset button (see Section 5-1).
Check fuse F1 and replace if open (see Section 6-6).
Check plug PLG6 connection.
Have Factory Authorized Service Agent check brushes, slip rings, and integrated rectifier SR2.
Check and adjust engine speed (see Section 6-5).
Check fuse F1 and replace if open (see Section 6-6).
Increase Fine Adjust control R1 setting.
High power output.
Low power output.
Erratic power output.
Check fuel level.
Check and adjust engine speed (see Section 6-5).
Check receptacle wiring and connections.
Have Factory Authorized Service Agent check brushes and slip rings.
OM-175 104 Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Engine
Trouble
Remedy
Check fuse F6, and replace if open (see Section 6-6).
Check battery voltage.
Engine will not crank.
Check battery connections and tighten if necessary
.
Check plug PLG4 and plug PLG8 connections.
Have Factory Authorized Service Agent check Engine Control switch S2.
Check fuel level.
Engine will not start.
Check battery voltage.
Check battery connections and tighten if necessary
.
Check oil level. Check low oil pressure shutdown switch (see Section 3-4).
Have Factory Authorized Service Agent check fuel shutoff solenoid FS1.
Check oil level. Check low oil pressure shutdown switch (see parts list for location).
Engine starts but stops when Engine
Control switch returns to Run position.
Check and refill crankcase with proper viscosity oil for operating temperature, if necessary
.
Engine stopped during normal opera
-
Check fuel level.
tion.
Check oil level. Check low oil pressure shutdown switch (see Section 3-4).
Periodically recharge battery (approximately every 3 months).
Replace battery
.
Check voltage regulator and connections according to engine manual.
Have Factory Authorized Service Agent check fuel shutoff solenoid FS1.
Battery Discharges between uses.
Clean battery, terminals, and posts with baking soda and water solution; rinse with clear water
.
Periodically recharge battery (approximately every 3 months).
Replace battery
.
Check voltage regulator and connections according to engine manual.
Engine idles but does not come up to
weld speed.
Have Factory Authorized Service Agent check auto idle module PC1, and current transformer CT1.
Unstable or sluggish engine speeds.
Readjust throttle linkage if necessary. Check throttle solenoid TS1 for smooth operation.
Tune-up engine according to engine manual.
Engine does not return to idle speed.
Remove weld and auxiliary power loads.
Check throttle linkage for smooth, non-binding operation.
Have Factory Authorized Service Agent check idle module PC1, current transformer CT1, Engine Con
trol switch S2, and throttle solenoid TS1.
-
OM-175 104 Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 – ELECTRICAL DIAGRAM
SB-180 690-B
Figure 7-1. Circuit Diagram For Welding Generator
OM-175 104 Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8 – PARTS LIST
ST-801 432-B
Figure 8-1. Main Assembly
OM-175 104 Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 8-1. Main Assembly
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .
. .
. .
. .
. .
. .
. .
. .
. .
. .
. .
1
1
2
3
3
4
5
6
7
8
9
. . . . . . . . . . . . +159 907 . . . COVER, top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . ♦+169 441 . . . COVER, top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 108 487 . . . LABEL, warning: falling equipment can cause serious injury . . . . . . . . . . .
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
4
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
. . . . . . . . . . . . . . 169 329 . . .
. . . . . . . . . . . . ♦169 442 . . .
P
ANEL, side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PANEL, side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 159 914 . . . UPRIGHT, base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 168 640 . . . SEAL, tank fuel filler neck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 164 928 . . . SEAL, barrel 11.78 ID x .378thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 178 497 . . . PANEL, rear lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 147 601 . . . CAP, tank screw-on w/vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 178 498 . . . TANK, fuel 8.5gal (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 10 . . . . . . . . . . . . . . 178 632 . . . . . FITTING, stand pipe hose .250 x 7.325 lg . . . . . . . . . . . . . . . . . . . . . . . . .
. . 11 . . . . . . . . . . . . . . 121 652 . . . FILTER KIT, fuel w/clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 12 . . . . . . . . . . . . . . 173 088 . . . LABEL, engine maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 13 . . . . . . . . . . . . . . 173 065 . . . MUFFLER, exhaust engine w/heat shield (Included w/engine) . . . . . . . . .
. . 14 . . . . . . . . . . . . +173 042 . . . ENGINE, gas elec start (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 15 . . . . . . . . . . . . . . 165 271 . . . . . VALVE, oil drain 3/8-18NPTF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . TS1 . . . . . . . . . . . . . . . . . . SOLENOID, 14VDC .53A (see engine parts list) . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BRACKET, mtg solenoid (see engine parts list) . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 180 096 . . . TUNE-UP & FILTER KIT, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 066 698 . . . . . OIL FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 121 652 . . . . . FILTER/CLAMPS, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 067 272 . . . . . ELEMENT, air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 067 273 . . . . . AIR FILTER, wrapper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 067 007 . . . . . SPARK PLUG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 16 . . . . . . . . . . . . . . . Fig 8-3 . . . GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 24 . . . . . . . . . . . . . . 182 361 . . . KIT, holddown battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 18 . . . . . . . . . . . . . . 168 385 . . . LABEL, warning battery explosion can blind . . . . . . . . . . . . . . . . . . . . . . . . .
. . 19 . . . . . . . . . . . . +159 917 . . . DOOR, access battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 20 . . . . . . . . . . . . . . 173 921 . . . CABLE, bat pos (included w/engine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 21 . . . . . . . . . . . . . . 168 037 . . . BATTERY, stor 12V 430crk 75rsv GP58 dry . . . . . . . . . . . . . . . . . . . . . . . . .
. . 22 . . . . . . . . . . . . . . 082 319 . . . CABLE, bat neg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 172 669 . . . CABLE, bat neg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 23 . . . . . . . . . . . . . . 173 043 . . . BRACKET, mtg engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 24 . . . . . . . . . . . . . . 165 660 . . . BRACKET, mtg generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 25 . . . . DC-Z . . . . 165 578 . . . STABILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 26 . . . . AC-Z . . . . 176 301 . . . REACTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 27 . . . . . . . . . . . . . . 164 920 . . . BRACKET, mtg stab/reactor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 28 . . . . . . . . . . . . . . 159 906 . . . PAN, base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 29 . . . . . . . . . . . . . . 160 844 . . . COVER, base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 30 . . . . . . . . . . . . +180 628 . . . PANEL, front lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 31 . . . . . . . . . . . . . . . Fig 8-2 . . . PANEL, front w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 32 . . . . SR1 . . . . 142 503 . . . RECTIFIER, si 1 ph 300A 400PIV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 33 . . . . . . . . . . . . . . 173 734 . . . LINK, jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 34 . . . . . 1T . . . . . 172 661 . . . BLOCK, stud connection 6 position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 35 . . . . . D4 . . . . . 135 184 . . . DIODE BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 36 . . . . SR2 . . . . 035 704 . . . RECTIFIER, integ 40A 800V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 37 . . . . . . . . . . . . . . 172 731 . . . HOLDER, fuse mintr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 38 . . . . . F1 . . . . *169 296 . . . FUSE, mintr gl 25A 125V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 39 . . . . . C1 . . . . . 176 719 . . . CAPACITOR, elctlt 1000uf 75VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 40 . . . . . . . . . . . . . . 177 136 . . . CLAMP, capacitor 2.500dia clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 41 . . . . CT1 . . . . . 179 494 . . . TRANSFORMER, current sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 42 . . . . . R2 . . . . . 165 599 . . . RESISTOR, WW adj 225W 0-6 ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . RC4 . . . . 116 045 . . . CONNECTOR & PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . PLG6 . . . . 136 810 . . . CONNECTOR & PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . PLG4 . . . . . . . . . . . . . . . CONNECTOR, (see engine parts list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . RC6 . . . . 168 844 . . . CONNECTOR, rect 4 pin/skt rcpt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 43 . . . . . . . . . . . . . . 134 792 . . . LABEL, warning general precautionary . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
♦ Part of Optional 043 051 Stainless Steel kit.
*Recommended Spare Parts.
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
OM-175 104 Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 8-2. Panel, Front w/Components (Fig 8-1 Item 44)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .
. .
. .
. .
. .
. .
. .
. .
. .
1
2
3
4
5
6
7
8
9
. . . . . . . S1 . . . . . . 162 671 . . . SWITCH, polarity 5 position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . NAMEPLATE, (order by model and serial number) . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 165 602 . . . PANEL, front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . S3 . . . . . . 165 487 . . . SWITCH, selector 4 position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . R1 . . . . . . 117 243 . . . RHEOSTAT, WW 100W 10 ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . PC1 . . . . . . 142 724 . . . MODULE, pull to idle 5 pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . S2 . . . . . . 176 606 . . . SWITCH, ignition 4 position w/out handle . . . . . . . . . . . . . . . . . . . . . . . .
. . . . GFCI2,3 . . . . 147 939 . . . RECEPTACLE, str dx grd 2P3W 15A 125V . . . . . . . . . . . . . . . . . . . . . . .
. . . . . CB1,2 . . . . . 117 501 . . . CIRCUIT BREAKER, man reset 1P 40A 250VAC . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
2
2
2
1
1
1
1
2
1
1
3
3
1
4
2
1
. . 10 . . . . . CB3,4 . . . . . 093 996 . . . CIRCUIT BREAKER, man reset 1P 20A 250VAC . . . . . . . . . . . . . . . . . .
. . 11 . . . . . . HM . . . . . . 145 247 . . . METER, hour 12-24VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 12 . . . . . . . . . . . . . . . . . 175 010 . . . CONTROL, push/pull . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 13 . . . . . . . . . . . . . . . . . 119 014 . . . LEVER, switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 14 . . . . R3,VR1 . . . . 046 819 . . . SUPPRESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 15 . . . Work, Elect . . 099 255 . . . TERMINAL, pwr output neutral . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 16 . . . . . . RC1 . . . . . . 164 704 . . . RECEPTACLE, str 3P4W 50A 125/250V . . . . . . . . . . . . . . . . . . . . . . . . .
. . 17 . . . . . . . . . . . . . . . . . 083 030 . . . STUD, brs .250-20 x 1.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 18 . . . . . . . . . . . . . . . . . 010 915 . . . WASHER, flat .250 ID brs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 19 . . . . . . . . . . . . . . . . . 601 836 . . . NUT, .250-20 brs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 20 . . . . . . . . . . . . . . . . . 159 921 . . . BEZEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 21 . . . . . . . . . . . . . . . . . 147 195 . . . NUT, .375-27 nyl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 22 . . . . . . . . . . . . . . . . . 148 956 . . . HANDLE, switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 23 . . . . . . . . . . . . . . . . . 097 924 . . . KNOB, pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
3
4
5
6
7
8
9
10
24
23
22
21
20
17
14
13
12
11
18
19
16
ST-800 816-A
15
Figure 8-2. Panel, Front w/Components
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
OM-175 104 Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Part
No.
Description
Quantity
Figure 8-3. Generator (Fig 8-1 Item 21)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .
. .
. .
. .
. .
. .
. .
. .
. .
1
2
3
4
5
6
7
8
9
. . . . 013 367 . . LABEL, warning moving parts can cause serious injury . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 165 818 . . LABEL, warning engine fuel can cause fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . +179 500 . . STATOR, generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 159 909 . . ROTOR, generator (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 053 390 . . . . BEARING, ball rdl sgl row 1.370 x 2.830 x .6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 160 566 . . . . FAN, rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 172 683 . . ADAPTER, engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 142 156 . . SCREW, .375-16 x 1.750hexhd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 160 573 . . STUD, stl .375-16 x 17.125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
4
4
1
2
2
2
1
4
4
1
1
. . 10 . . . . 125 548 . . HOLDER, brush elect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 11 . . . . 005 614 . . HOLDER, brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 12 . . . *126 984 . . BRUSH w/SPRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 13 . . . . 161 306 . . CAP, brushholder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 14 . . . . 047 879 . . BAR, retaining brushholder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 15 . . . . 010 910 . . WASHER, flat .406 ID stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 16 . . . . 010 909 . . NUT, .375-16 stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 17 . . . . 160 943 . . ENDBELL, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 18 . . . . 143 220 . . . . O-RING, 2.859 ID x .139CS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
4
5
2
3
7
1
8
9
10
11
12
13
18
17
14
15
ST-800 798
16
Figure 8-3. Generator
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
*Recommended Spare Parts.
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
OM-175 104 Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
|