NETGEAR 54 Mbps
Wireless USB 2.0 Adapter
WG111v2 User Manual
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
202-10081-03
January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Caution: Any change or modification to the product not expressly approved by Netgear could void the user’s
authority to operate the device.
FCC RF Radiation Exposure and SAR Statements
SAR Statement
The Netgear WG111v2 has been tested for body-worn Specific Absorption Rate (SAR) compliance. The FCC has
established detailed SAR requirements and has established that these requirements have been met while installed in host
notebook computer.
RF Exposure Information
The radio module has been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the
requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency
devices. This model meets the applicable government requirements for exposure to radio frequency waves. The highest
SAR level measured for this device was 0.532 W/kg.
Canadian Department of Communications Industry Canada (IC) Notice
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet appareil numérique de la classe B
est conforme à la norme NMB-003 et CNR-210 du Canada.
“To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to
licensing.”
“Pour empêcher que cet appareil cause du brouillage au service faisant l’objet d’une licence, il doit être utilisé à
l’intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son
antenne d’émission) est installé à l’extérieur, il doit faire l’objet d’une licence.”
Europe - EU Declaration of Conformity with Regard to R&TTE Directive 1999/5/EC
A printed copy of the EU Declaration of Conformity certificate for this product is provided in the WG111v2 product
package.
Èesky
[Czech]
NETGEAR, Inc. tímto prohlašuje, že tento NETGEAR 54 Mbps Wireless USB2.0
Adapter WG111v2 je ve shodì se základními požadavky a dalšími pøíslušnými
ustanoveními smìrnice 1999/5/ES.
Dansk
[Danish]
Undertegnede NETGEAR, Inc. erklærer herved, at følgende udstyr NETGEAR 54 Mbps
Wireless USB2.0 Adapter WG111v2 overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt NETGEAR, Inc., dass sich das Gerät NETGEAR 54 Mbps Wireless
USB2.0 Adapter WG111v2 in Übereinstimmung mit den grundlegenden Anforderungen
und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab NETGEAR, Inc. seadme NETGEAR 54 Mbps Wireless USB2.0
Adapter WG111v2 vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
iii
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Hereby, NETGEAR, Inc., declares that this NETGEAR 54 Mbps Wireless USB2.0
Adapter WG111v2 is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente NETGEAR, Inc. declara que el NETGEAR 54 Mbps Wireless
USB2.0 Adapter WG111v2 cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR, Inc. ΔΗΛΩΝΕΙ ΟΤΙ NETGEAR 54 Mbps Wireless
USB2.0 Adapter WG111v2 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ
ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente NETGEAR, Inc. déclare que l'appareil NETGEAR 54 Mbps Wireless
USB2.0 Adapter WG111v2 est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente NETGEAR, Inc. dichiara che questo NETGEAR 54 Mbps Wireless
USB2.0 Adapter WG111v2 è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo NETGEAR, Inc. deklarç, ka NETGEAR 54 Mbps Wireless USB2.0 Adapter
WG111v2 atbilst Direktîvas 1999/5/EK bûtiskajâm prasîbâm un citiem ar to saistîtajiem
noteikumiem.
Lietuviø
Šiuo NETGEAR, Inc. deklaruoja, kad šis NETGEAR 54 Mbps Wireless USB2.0 Adapter
[Lithuanian]
WG111v2 atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart NETGEAR, Inc. dat het toestel NETGEAR 54 Mbps Wireless USB2.0
Adapter WG111v2 in overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, NETGEAR, Inc., jiddikjara li dan NETGEAR 54 Mbps Wireless USB2.0
Adapter WG111v2 jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li
hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, NETGEAR, Inc. nyilatkozom, hogy a NETGEAR 54 Mbps Wireless USB2.0
Adapter WG111v2 megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC
irányelv egyéb elõírásainak.
Polski [Polish] Niniejszym NETGEAR, Inc. oœwiadcza, ¿e NETGEAR 54 Mbps Wireless USB2.0
Adapter WG111v2 jest zgodny z zasadniczymi wymogami oraz pozosta³ymi stosownymi
postanowieniami Dyrektywy 1999/5/EC.
Português
NETGEAR, Inc. declara que este NETGEAR 54 Mbps Wireless USB2.0 Adapter
[Portuguese] WG111v2 está conforme com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.
Slovensko
[Slovenian]
NETGEAR, Inc. izjavlja, da je ta NETGEAR 54 Mbps Wireless USB2.0 Adapter
WG111v2 v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloèili direktive 1999/5/
ES.
Slovensky
[Slovak]
NETGEAR, Inc. týmto vyhlasuje, že NETGEAR 54 Mbps Wireless USB2.0 Adapter
WG111v2 spåòa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/
ES.
iv
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Suomi
[Finnish]
NETGEAR, Inc. vakuuttaa täten että NETGEAR 54 Mbps Wireless USB2.0 Adapter
WG111v2 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar NETGEAR, Inc. att denna NETGEAR 54 Mbps Wireless USB2.0
Adapter WG111v2 står I överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Product and Publication Details
Model Number:
WG111v2
Publication Date:
Product Family:
January 2007
Wireless Adapter
Product Name:
NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2
Home or Business Product:
Language:
Home
English
Publication Part Number:
202-10081-03
v
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
About This Manual
Audience, Conventions, and Scope ................................................................................. ix
What You Need Before You Begin .....................................................................................1
Verify System Requirements .......................................................................................1
Observe Wireless Location and Range Guidelines .....................................................1
What Is in the Box .......................................................................................................2
Default Wireless Settings ............................................................................................2
Installation Instructions ......................................................................................................3
Connecting to Wireless Networks and the Internet ...........................................................6
The Smart Wizard Status Bar ......................................................................................7
Icon Colors ..................................................................................................................8
Placing the USB Adapter Cradle .......................................................................................8
Removing the Software .....................................................................................................9
Upgrading the Wireless Adapter Software ......................................................................10
Understanding the Smart Wizard ....................................................................................12
Viewing Wireless Networks in Your Area .........................................................................12
Finding a Network ............................................................................................................14
Profiles .............................................................................................................................15
Adding Profiles ..........................................................................................................15
Setting up a Profile to Connect to an Access Point or Router .........................................15
Setting up a Computer-to-Computer (Ad Hoc) Profile .....................................................17
Starting a Computer-to-Computer (Ad Hoc) Network Connection ............................19
Wireless Security .............................................................................................................20
Know Your Wireless Network Settings ......................................................................20
Wireless Network Name (SSID) and Security Settings ...................................................21
vii
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up WEP Encryption Security ...............................................................................22
Setting up WPA2-PSK Security .......................................................................................23
Setting up WPA-PSK Security .........................................................................................24
Advanced Settings ....................................................................................................25
Statistics Page .................................................................................................................26
About Page ......................................................................................................................27
Troubleshooting
Troubleshooting Tips .......................................................................................................29
Frequently Asked Questions ...........................................................................................29
Ad Hoc mode is not working correctly .......................................................................30
The Wireless Adapter is not getting an IP address ...................................................31
Why do I see two Wireless Adapter icons in the System Tray? ................................31
Default Configuration Settings and Technical Specifications
Default Configuration Settings .........................................................................................33
Technical Specifications ...................................................................................................34
Related Documents
viii
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
Audience, Conventions, and Scope
This manual assumes that you have basic to intermediate computer and Internet skills. However,
tutorial information is provided on the NETGEAR website.
This manual uses the following typographical conventions:
Italics
Emphasis, books, CDs, URL names
User input
Bold
This manual uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest.
Tip: This format is used to highlight a procedure that will save time or resources.
This manual is written according to these specifications:
Product Version
NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2
January 2007
Manual Publication Date
Note: Product updates in English language are available on the NETGEAR website at
ix
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
x
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Setup
The NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2 lets you connect a PC computer to
wireless networks. It is designed for PC computers running Microsoft Windows. For information
about product features and compatible NETGEAR products, please see the NETGEAR website at
This chapter describes how to install your wireless USB adapter and set up basic wireless
connectivity on your Wireless Local Area Network (WLAN). Advanced wireless network set up is
covered in “Network Connections and Wireless Security” on page 11.
What You Need Before You Begin
You must verify that your computer meets the minimum system requirements and identify the
wireless network settings of the wireless network where you will connect before you can set up
your wireless USB adapter and connect.
Verify System Requirements
Before installing the Wireless Adapter, make sure that these minimum requirements have been
met. You must have a computer with:
•
•
•
•
A Pentium 300 MHz or higher compatible processor with an available USB port.
A CD drive.
10 MB of free hard disk space.
Windows 2000, XP, or Vista.
Observe Wireless Location and Range Guidelines
Computers can connect over wireless networks indoors at a range which vary significantly based
on the location of the computer with the Wireless Adapter. For best results, avoid potential sources
of interference, such as:
•
•
•
Large metal surfaces
Microwave ovens
2.4 GHz Cordless phones
1
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
In general, wireless devices can communicate through walls. However, if the walls are constructed
with concrete, or have metal, or metal mesh, the effective range will decrease if such materials are
between the devices.
What Is in the Box
The product package should contain the following items:
•
•
•
•
NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2
Installation Guide
Plastic cradle and fasteners to hold the WG111v2
NETGEAR CD, including:
–
–
Driver and Configuration Utility Software
This User Manual
•
Warranty and Support information card
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product.
Default Wireless Settings
If this is a new wireless network installation, use the factory default settings to set up the network
and verify wireless connectivity. If this is an addition to an existing wireless network, you need the
wireless network and wireless security settings that are already defined.
Your Wireless Adapter factory default basic settings are:
•
Network Name Service Set Identification (SSID): ANY
Note: In order for the Wireless Adapter to communicate with a wireless access point
or wireless adapter, all devices must be set up to use the same wireless network
name (SSID).
•
•
Network Mode (Infrastructure or Ad-hoc): Infrastructure
Data security WEP, WPA2-PSK, or WPA-PSK encryption: Disabled
The section below provides instructions for setting up the Wireless Adapter for basic wireless
connectivity to an access point.
2
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
The instructions in this chapter are for an Access Point (Infrastructure) installation. Wireless
security, advanced settings, and Computer-to-Computer (Ad Hoc) instructions are covered in
“Network Connections and Wireless Security” on page 11.
Follow the instructions below to install the Wireless Adapter.
1. First, install the software. Insert the NETGEAR CD. If the CD main page does not appear,
double click Autorun.exe on the CD.
a. Click Install the Software.The Check for Updates window will open.
b. If you are connected to the Internet, click Check for Updates. If not, you can choose to
install from the CD.
c. When the Installation Complete message appears, click Next.
d. On the Smart Wizard screen, click Next to proceed with the Smart Wizard setup.
Figure 1
2. Now, when prompted, insert your wireless USB adapter.
a. Click Next to proceed. Windows will discover the adapter and continue the software
installation process.
3
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
b. Follow the Windows prompts to complete the software installation.
c. If a Windows logo certification warning appears, click Continue to proceed with the
installation.
d. When the Windows software installation is complete, click Finish.
Figure 2
either with the NETGEAR Smart Wizard (recommended) or the Windows Configuration
•
NETGEAR Smart Wizard: Reveals more information about each network and makes it
easier to troubleshoot network connection problems. See “The Smart Wizard Status Bar”
on page 7 and “Statistics Page” on page 26.
•
Windows Zero Configuration Utility: See the Windows documentation or see the link to
“Windows XP and Vista Wireless Configuration Utilities” on page 35.
Figure 3
4
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
4. Use the Smart Wizard to set up your Wireless Adapter
a. When prompted, click Next to let the wizard help you connect to a network
(recommended).
Figure 4
b. Select the wireless network from the drop-down list, and the wizard records your choice.
Note: Hidden networks do not broadcast the Network Name (SSID). These
networks are in the drop-down list, but the Network Name (SSID) is blank
If the network uses security, then the Smart Wizard detects it..
Figure 5
c. Follow the Wizard steps for Security (if used) and for saving a Profile.
d. After you have reviewed the settings, click Finish.
5
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
The
icon appears in the System Tray and on the desktop. The wizard initiates your
wireless connection. It could take up to a minute for your wireless connection to be
established.
The Smart Wizard Settings page opens.
Figure 6
5. Use the status bar to verify your wireless connectivity. For more information about
connecting, see “Connecting to Wireless Networks and the Internet” on page 6.
Connecting to Wireless Networks and the Internet
The Wireless Adapter has indicators that show the status of your connection to a wireless network
and to the Internet:
•
Icon: After you install the software, this icon appears on the desktop and in the lower
right of the Windows task bar. It is color coded to show the status of the connection. See “The
Smart Wizard Status Bar” on page 7.
•
Smart Wizard Status Bar: Clicking on the system tray icon opens the Smart Wizard. The
status bar at the bottom of the page shows details about your wireless and Internet connection.
6
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
The Smart Wizard Status Bar
Click the
icon to open the Smart Wizard so you can view the status bar. The Smart Wizard
Settings page opens. The status bar is at the bottom of the page.
signal strength
connection
status
Router/Internet
connection indicator
Unlocked: Network does not use security
Locked: Network uses security
Figure 7
•
•
Connection Status: The color shows the connection status.
Signal Strength: Shows the signal strength of the wireless network. If the signal is poor, then
try moving closer to the wireless access point.
•
•
Lock icon: Shows if security is used on the network.
Router/Internet connection indicator: This shows the progress of your connection. By
default, this feature is on.
Figure 8
If you selected Europe during the WG111v2 installation, this feature is disabled.
The Router/Internet connection indicator is useful in isolating a problem. For example, if you are
connected to a router, but not to the Internet, then check the router’s Internet connection.
Connection Indicator
Description
Connected to Internet
or IP Address
Wireless Internet connection OK.
Connected to Router
Wireless connection to router OK but no Internet
connection at router.
___.___.___.___ or
169.254..x.x
Wireless connection to a router OK but there is a
problem with the router. See “Troubleshooting”.
If you right-click the System Tray icon, you can disable the Internet notification feature by
clearing the check mark on this line. If you do so, then only the IP address is shown.
7
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Figure 9
If you selected Europe during the WG111v2 installation, you will not see the “Enable Internet
Connected Notification” option.
Icon Colors
The icon is on the desktop and in the Windows System Tray. The System Tray resides on one end
of the taskbar in the Microsoft Windows desktop.
Color
Condition
Description
Red
The wireless USB adapter
has no connection to any
other wireless node.
The Wireless Adapter can not link to any other wireless node
or the link is lost. Check your configuration or try moving to a
location where the wireless signal quality is better.
Yellow
Green
The wireless USB adapter
has a connection with another spot, such as closer to the wireless access point. Also, look
wireless node.
The wireless link is weak. You may need to move to a better
for possible interference such as a 2.4 GHz cordless phone or
large metal surface.
The wireless USB adapter
The wireless USB adapter has established good
has a connection with another communication with an access point and the signal quality is
wireless node. strong.
Placing the USB Adapter Cradle
You can attach the Wireless Adapter directly to a USB port on your computer, or use the USB
cable to extend the range and obtain better wireless reception.
Follow these instructions to use the USB cable, plastic cradle, and loop and hook fastener provided
in the package for better USB Adapter placement on a notebook computer:
1. The Wireless Adapter comes with three black fasteners. Locate the one that has a prickly side
and attach it to the plastic cradle on the middle of the outside rear.
2. Insert the Wireless Adapter in the plastic cradle.
8
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
3. Place one of the other pieces of loop and hook fastener on the back of the monitor near the top
for better reception.
Tip: Place the last piece of fastener on the side of monitor nearest your wireless
access point.
4. Join the pieces of the fastener to attach the USB Adapter in the plastic cradle to the notebook
or desktop monitor.
Figure 10
See the installation instructions for your operating system before attaching the USB cable to the
USB Adapter and your computer
Removing the Software
You can remove the Wireless Adapter software in these two ways:
•
Navigate the Windows Start menu to the NETGEAR 54 Mbps Wireless USB2.0 Adapter
WG111v2 program group, select the uninstall option, and follow the screen prompts.
•
Navigate the Windows Start menu to the Control Panel Add or Remove Program item, select
the NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2 option, and follow the screen
prompts.
9
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Upgrading the Wireless Adapter Software
Upgrades may be available at the NETGEAR website. To install an upgrade, follow these steps.
2. Click the latest version of upgrade.
3. Examine the Release Note. Make sure to read any warnings and Known Problems.
4. Download the upgrade using the link in the Release Note.
5. Follow the Release Note installation instructions.
10
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Connections and Wireless Security
This chapter explains how to use your Wireless Adapter to connect to your Wireless Local Area
Network (WLAN) and how to set up wireless security for the Wireless Adapter so that it matches
the wireless security settings for your network.
Disabling the Windows Zero Configuration Utility
If you chose the Windows XP or Windows Vista Zero Configuration utility during installation, and
now you want to use the Smart Wizard, then you need to disable the Windows utility.
To disable the Windows Zero Configuration utility:
1. Attach the wireless adapter to a USB port for your computer.
2. Go to Windows Start menu and select Network Connections.
3. On the Network connections page, select the Wireless Network Connection and right-click to
choose the Properties option.
Figure 11
4. Click the Wireless Networks tab. Then clear the “Use Windows to configure my wireless
settings” check box.
11
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Understanding the Smart Wizard
These instructions explain how to use the NETGEAR WG111v2 Smart Wizard to change the
WG111v2 wireless settings.
When you have installed the software from the NETGEAR CD, the
icon appears on your
desktop and in the Windows System Tray. The Windows System Tray is located on the Windows
taskbar. You can either double-click this icon on the desktop, or click it in the System Tray at any
time, to use the Smart Wizard. This software automatically restarts when you reboot your
computer.
The Smart Wizard provides a complete and easy to use set of tools to:
•
•
•
•
•
View details about wireless networks in your area.
Choose the network that you want to use.
Configure wireless settings for your wireless USB adapter
Save your wireless network settings in profiles.
Remove or reinstall the wireless adapter software.
The following sections in this chapter explain how to use the Smart Wizard.
Viewing Wireless Networks in Your Area
You can use the Networks tab to view all available wireless networks in your area. You can also
scan to search for wireless networks and refresh the page.
To view information about wireless networks:
1. Use the
icon to open the Smart Wizard. The Settings tab page opens.
2. Click the Networks tab to view the following page.
12
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
You can click a column
heading to sort.
If many networks use
the same channel they
can interfere with each
other.
The Status bar shows
your network connection
and Internet connection.
Figure 12
The screen shows the following information for each network scanned:
•
Network Name (SSID): The name assigned to a wireless network. This is the same as the
SSID or ESSID configuration parameter. Note that as a security measure, some wireless
access points do not broadcast their SSID. In such cases, the SSID field will be blank even
though the rest of the information will still be displayed.
•
•
•
•
Channel: The channel determines which operating frequency will be used.
Security: Identifies whether the wireless network uses WEP or WPA-PSK security settings.
Signal: Identifies the signal strength of the communications.
MAC Address: Identifies the hardware address (MAC Address) of the wireless device
broadcasting this information.
•
to-Computer (Ad Hoc)
The buttons located at the bottom of the Networks tab are:
•
Help: Display online help.
•
•
•
Find a Network: Find and connect to a network. See “Finding a Network” on page 14.
Connect: Connect to the network that you selected.
Scan: Check for wireless networks. Clicking Scan refreshes the page.
•
Close: Close the window of the Wizard.
13
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Finding a Network
During the Wireless Adapter software installation, the Smart Wizard lists the available networks.
After installation you can use the Find a Network button on the Network tab at any time to view
the available networks and select the one that you want to use.
Note: Make sure that you know the security settings for the network that you want to use.
For example, if WEP is used then you need to know the WEP key. If you use
secure networks frequently, set up profiles for each network with the wireless
network and security settings.
To find a Network, follow these steps:
1. Use the
icon to open the Smart Wizard.
The Settings tab page opens.
2. Click Find a Network.
3. Select a network from the
drop-down list. If you select a hidden network then you must enter the SSID. Click Next.
4. Follow the steps of the wizard to specify the wireless security if used, and to create a profile.
5. Review you settings, and click Finish.:
Hidden
Figure 13
14
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
The Smart Wizard initiates your wireless connection. You can use the Status Bar to verify your
network connection. For more information, see “The Smart Wizard Status Bar” on page 7.
Profiles
The WG111v2 Smart Wizard uses profiles to store all the settings for a particular wireless
network. There are two special profile names: Default and Profile.
•
Default: The Profile named Default automatically scans for any available network. You
cannot change this profile name.
•
Profile: If you do not enter a name in the Profile Name box, then the name Profile is used to
save your settings. If you do this more than once then you will be asked if you want to replace
the previous settings stored in Profile.
Adding Profiles
You can store multiple profiles and recall the one which matches the network you want to join.
If you use your computer to connect to different wireless networks, you can create a profile for
each wireless network. Then, you can easily load the profile that has all the settings that you need
to join the network you are using at the time.
There are two types of wireless network profiles that you can set up:
•
Access Point (Infrastructure) – Connect to an access point or router with the 802.11
infrastructure mode. For example, this mode is used when computers in a house connect to an
access point that is attached to a router, which lets multiple computers share a single cable or
DSL broadband Internet connection.
•
Computer-to-Computer (Ad Hoc) – Connect directly to another computer with the 802.11
ad hoc mode. For example, Ad Hoc mode is used when two Windows computers are
configured with file and print sharing enabled and you want to exchange files directly between
them.
For more information on 802.11 wireless network modes, see the wireless reference document at:
Setting up a Profile to Connect to an Access Point or Router
To set up the Wireless Adapter to connect to a wireless access point or router:
15
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
1. Use the
icon to open the Smart Wizard. The Settings page opens.
2. Enter the network settings.
a. In the Network Type section, be sure that Access Point (Infrastructure) is selected.
b. In the Profile box, type the name of the profile.
c. In the Network Name (SSID) field select a network or enter the SSID.
Figure 14
Note: You will not get a wireless network connection unless the network SSID
matches exactly the SSID used by the access point.
3. Save your settings in a Profile.
a. Click Save Profile.
All the configuration settings are saved in this profile.
b. Click Apply.
c. Click Close to exit the wizard, or Cancel to return to the previous settings.
your browser to connect to the Internet, or check for file and printer access on your network.
If you cannot connect, check the Status bar in the Smart Wizard. See “The Smart Wizard
Status Bar” on page 7. For problems with accessing network resources, the Windows Client
and File and Print Sharing software might not be installed and configured properly on your
computers. See the link to “Internet Networking and TCP/IP Addressing” on page 35.
16
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Setting up a Computer-to-Computer (Ad Hoc) Profile
The Computer-to-Computer setting uses Ad Hoc mode. Ad Hoc mode is an 802.11 networking
framework in which devices or computers communicate directly with each other, without the use
of an access point. For example, this mode is used when two Windows computers are configured
with file and print sharing enabled and you want to exchange files directly between them.
Note: Ad Hoc mode will not work using DHCP settings. Ad Hoc mode requires either
static IP addresses (such as 192.168.0.1) or the IPX protocol. For instructions on
setting up static IP addresses on a Windows PC, refer to the PC Networking
Tutorial included on the NETGEAR CD.
To create an Ad Hoc mode profile:
1. Use the
icon to open the Smart Wizard. The Settings page opens.
2. Enter the network settings.
a. Select Computer-to-Computer (Ad Hoc) for the Network Type.
b. Select or enter the Network Name (SSID) for the Ad Hoc network.
c. In the Profile box, type the name of the profile.
d. Click Apply
Figure 15
17
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
3. Save your settings in a Profile.
a. Click Save Profile.
All the configuration settings are saved in this profile.
b. Click Apply.
c. Click Close to exit the Smart Wizard, or Cancel to return to the previous settings.
4. Configure the PC network settings.
a. Configure each PC with either a static IP address or with the IPX protocol.
b. Restart the PCs.
5. Verify wireless connectivity between your peer devices.
You can use the ping utility to verify your wireless connection
a. On the Windows taskbar click Start, and then click Run.
b. Assuming the target PC is configured with 192.168.0.1 as its IP address, type ping -t
192.168.0.1 and then click OK.
Figure 16
c. This sends a continuous ping to the device with the 192.168.0.1 static IP address. The ping
response should change to “reply.”
Figure 17
18
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
At this point the connection is established. For more information about using ping, see
Note: If you cannot connect, see “Placing the USB Adapter Cradle” on page 8. Also,
for problems with accessing network resources, the Windows Client and File
and Print Sharing software might not be installed and configured properly on
your computers. Please see the link to “Internet Networking and TCP/IP
Addressing” on page 35.
Starting a Computer-to-Computer (Ad Hoc) Network Connection
1. On the Settings tab page of the Smart Wizard, select or type the Network Name (SSID).
2. Select the Computer-to-Computer (Ad Hoc) network type.
3. Click Initiate Ad Hoc. The Ad Hoc Setting dialog box opens:
Figure 18
4. In the Start Ad Hoc field, choose the wireless standard (802.11b, or 802.11g) for your Ad Hoc
computer-to-computer network.
5. In the Channel field, Automatic should work.
Note: If there is interference from another nearby wireless device, use the Networks
tab page to see which channels are in use in your area. Then use a different
channel. For example, if your neighbors use channel 6 and the signal strength
is strong, then channels 4-8 would probably be poor choices for you.
6. Click OK. The Wireless Adapter automatically selects the highest connection speed.
19
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Wireless Security
Many networks use wireless security to encrypt wireless data communications. If you try to
connect to a network with wireless security the Smart Wizard detects it. Before you can use that
network you must set up the Wireless Adapter with the same SSID, wireless security, and security
settings as that network. If you do not know what these are, contact the person who set up the
network.
The Wireless Adapter supports the following types of wireless security:
•
•
•
Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK)
Wi-Fi Protected Access Pre-Shared Key (WPA-PSK)
Wired Equivalent Privacy (WEP)
For more information about wireless security, see the Web link to “Wireless Communications” on
page 35 or the wireless reference document at:
In addition to the wireless security features, networks should use LAN network security features
such as requiring a user name and password to access the shared resources in the network.
The procedures below explain how to configure the wireless encryption settings of your Wireless
Adapter.
Know Your Wireless Network Settings
You will need to know the settings for your wireless network. The form on the next page is set up
so that you can record this information. You can use either of these two methods to keep track of
these settings:
•
Print the form on the next page and fill it out. If you are uncomfortable writing out secure
information, put a “hint” to yourself instead of the actual information. Put the form where it
will be very easy for you to remember, or save two copies and put them in different places.
•
Save the information in a document on your computer. Later you can search for words such as
SSID to locate the information.
20
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Wireless Network Name (SSID) and Security Settings
Print this form, fill in the configuration parameters and put it in a safe place for possible future
reference. For an existing wireless network, the person who set up the network will have this
information.
•
Network Name (SSID): The Service Set Identification (SSID) identifies the wireless local
area network. Any (First available network) is the default WG111v2 wireless network name
(SSID). You may customize it using up to 32 alphanumeric characters. Write your customized
wireless network name (SSID) on the line below.
Note: The SSID in the wireless access point is the SSID you configure in the wireless
USB adapter. For the access point and wireless nodes to communicate with
each other, all must be configured with the same SSID.
Wireless network name (SSID): ______________________________
•
If WEP Authentication is Used.
–
WEP Encryption key size. Identify one: 64-bit or 128-bit. The encryption key size must
the wireless network settings.
–
Data Encryption (WEP) Keys. There are two methods for creating WEP data encryption
keys. Whichever method you use, record the key values in the spaces below.
•
Passphrase method. ______________________________ These characters are case
sensitive. Enter a word or group of printable characters and click the Generate Keys
button. Not all wireless devices support the passphrase method.
•
Manual method. These values are not case sensitive. For 64-bit WEP, enter 10 hex
digits (any combination of 0-9 or a-f). For 128-bit WEP, enter 26 hex digits.
Key 1: _____________________________ Key 2: _____________________________
Key 3: _____________________________ Key 4: _____________________________
•
If WPA2-PSK or WPA-PSK Authentication is Used.
–
Passphrase: ______________________________ These characters are case sensitive.
Enter a word or group of printable characters. When you use WPA-PSK, the other devices
in the network will not connect unless they are set to WPA-PSK as well and are configured
with the correct Passphrase.
Use the procedures below to set up basic security settings in the WG111v2.
21
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Setting up WEP Encryption Security
Follow the steps below to configure WEP Encryption Security.
1. Run the Wireless Adapter Smart Wizard.
a. Make sure the software is installed and the Wireless Adapter is into the USB port in your
computer.
b. Use the
icon to open the Smart Wizard. The Settings tab page opens.
Figure 19
2. Configure the Security settings.
a. In the Profile box, select the profile or type in a profile name.
b. In the Network Name (SSID) field select the network, or enter the SSID.
Note: You will not get a wireless network connection unless the network SSID
matches exactly what is configured in the access point.
c. In the Security section, select WEP.
3. Select the WEP encryption strength you will use.
The choices are:
•
•
64-bit WEP data encryption
128-bit WEP data encryption
Note: The 128-bit encryption keys require more processing, and slow performance
slightly.
22
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
4. Select Create with Passphrase and enter the passphrase. The configuration utility will
automatically generate the WEP keys.
Note: The characters are case sensitive. Be sure to use the same passphrase for all the
wireless devices in the network.
If the passphrase method is not available in the other devices, you must manually enter the
keys to match exactly what is in the access point and other 802.11b wireless devices.
5. Save your settings in a Profile.
a. Click Save Profile. All the configuration settings are saved in this profile.
b. Click Apply.
c. Click Close to exit the configuration utility.
Setting up WPA2-PSK Security
Follow the steps below to configure WPA2-PSK Security.
1. Run the Wireless Adapter Smart Wizard.
a. Make sure the software is installed and the Wireless Adapter is fully inserted in a USB
port in your computer.
b. Use the
icon to open the Smart Wizard. The Settings tab page opens.
Figure 20
2. Configure the Security settings.
a. In the Profile box, select the profile or type in a profile name.
23
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
b. In the Network Name (SSID) field select the network, or enter the SSID.
matches exactly what is configured in the access point.
c. In the Security section, select WPA2-PSK [AES].
For more information about WPA2-PSK security, see the Web link to “Wireless
Communications” on page 35.
3. Save your settings in a Profile.
a. Click the Save Profile button. All the configuration settings are saved in this profile.
b. Click Apply.
c. Click Close to exit the Smart Wizard.
Setting up WPA-PSK Security
Follow the steps below to configure WPA-PSK Security.
1. Run the Wireless Adapter Smart Wizard.
a. Make sure the software is installed and the Wireless Adapter is fully inserted in a USB
port in your computer.
b. Use the
icon to open the Smart Wizard. The Settings tab page opens.
Figure 21
2. Configure the Security settings.
a. In the Profile box, select the profile or type in a profile name.
24
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
b. In the Network Name (SSID) field select the network, or enter the SSID.
matches exactly what is configured in the access point.
c. In the Security section, select WPA-PSK [TKIP].
For more information on WPA security, see the Web link to “Wireless Communications”
on page 35.
3. Save your settings in a Profile.
a. Click Save Profile. All the configuration settings are saved in this profile.
b. Click Apply.
c. Click Close to exit the Smart Wizard.
Advanced Settings
Most people do not need to change the Wireless Adapter Advanced Settings. If you cannot connect
without making changes, or if your Internet Service Provider (ISP) or network administrator
recommend changes, then some of these will be important to you.
On the Settings tab click Advanced Settings. Use the Help button to understand these options.
25
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Statistics Page
The Statistics page provides real time and historical trend information on the data traffic and
performance of your wireless adapter.
Figure 22
•
•
•
•
Transmit/Receive Performance (%): A real time graph identifying the total, receive, and
transmit utilization as a percentage the total possible.
Transmit, Receive, and Total (TxRx): Radio buttons let you select whether to display the
transmit performance, the receive performance, or both in the same graph.
Transmit Statistics: Identifies transmit megabits per second (Mbps), transmit packets per
second (Tx Packets/s), total transmitted packets, and transmit errors.
Receive Statistics: Identifies receive megabits per second (Mbps), receive packets per second
(Rx Packets/s), total received packets, and reception errors.
26
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
About Page
The About page displays the current software version information.
Figure 23
The following information is displayed in the About page:
•
Regional Domain: This is the region setting for the wireless adapter. The approved channels
for the region are automatically scanned. Governments regulate the channels used for wireless
transmission. Operating the wireless adapter in a different region may violate local laws.
•
•
•
Driver Version: The wireless adapter driver version.
Driver Date: The wireless adapter driver date.
MAC Address: The MAC address of the adapter. The Media Access Control address is a
unique 48-bit hardware address assigned to every network interface card. Some wireless
networks will restrict access based on a list of known MAC addresses. If you are
communicating with such a network, you would have to provide the address shown here to the
network administrator before you would be allowed to connect. Restricting access by MAC
address adds an obstacle against unwanted access to your network. However, if the only
wireless security that your network uses is MAC addressing, your data is easy for hackers to
read.
•
•
IP Address: The IP address assigned to this adapter.
Smart Wireless Utility: The version and date of the Smart Wizard.
27
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
28
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
This chapter provides information about troubleshooting your wireless USB adapter. After each
information about connecting to wireless networks and the Internet, see “Connecting to Wireless
Networks and the Internet” .
Also, for problems with accessing network resources, the Windows software might not be installed
and configured properly on your computers. Please refer to the link to “Internet Networking and
TCP/IP Addressing”.
Troubleshooting Tips
Symptom
Cause
Solution
I can connect to an This could be a
Check to make sure that the access point is physically
connected to the Ethernet network.
access point, but I
cannot connect to
physical layer
problem or a network Make sure that the IP addresses and the Windows networking
other computers on configuration
parameters are all configured correctly.
Restart the cable or DSL modem, router, access point, and
notebook PC.
the network or the
Internet.
problem.
Frequently Asked Questions
Use the information below to solve common problems you may encounter. Also, please refer to the
problem right away, go online and upgrade to the latest firmware for your adapter, using the link
above.
The Smart Wizard keeps asking me to save my settings
This is because you have made changes to the settings and the Smart Wizard is offering you the
chance to save the changes. If you want to avoid these Profile setting prompts, simply click Apply
before you close the Smart Wizard.
29
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Ad Hoc mode is not working correctly
You need to click the Initiate Ad Hoc button before you click Apply. Here is how you start an Ad
Hoc network:
1. Fill in the Network Name (SSID).
2. Select the Computer-to-Computer (Ad Hoc) Network Type.
3. Click Initiate Ad Hoc.
4. Accept the default settings or make your changes and click OK
5. Click Apply.
Note: Be sure all computers in your Ad Hoc network are configured with static IP
addresses in the same subnet.
Did the Wireless Adapter receive a valid IP address from the
Wireless Router/AP?
The easiest way is to click the System Tray icon to open the Wireless Adapter Smart Wizard. Then
check the IP address in the About page.
I cannot connect to the AP that I want from the Networks Tab.
On the Networks tab click Scan to refresh the list. If the ahe access point is available and there is
good signal strength there are a few possibilities:
•
If the access point (AP) is WPA-PSK protected, you need the correct WPA-PSK passphrase.
Otherwise, the Wireless Adapter will still be connected to the previous access point and you
will not be able to change to the WPA-PSK access point.
•
If the access point is WEP protected (either 64-bit or 128-bit encryption), you will be
prompted to enter the WEP encryption security information.
30
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
The Wireless Adapter is not getting an IP address
You probably upgraded your Wireless Adapter software and did not reboot your system.
To get an IP address assigned, you can either restart your computer or choose another access point
to connect to. If there are no additional access points for you to choose from, restart your system
and connect to your desired access point again.
Note: It does not usually help to shut down the Smart Wizard or disable/enable the
adapter.
Why do I see two Wireless Adapter icons in the System Tray?
If you see two icons in the System Tray at the bottom right corner of the screen, you have an older
software version installed on your system and it needs to be removed. See “Placing the USB
Adapter Cradle” or “Upgrading the Wireless Adapter Software” .
31
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
32
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Default Configuration Settings and Technical
Specifications
Default Configuration Settings
The following table lists the default settings of your Wireless Adapter.
Feature
Description
Smart Wizard
Wireless
Enabled
Wireless Communication
Enabled
Wireless Network Name (SSID)
Security
Any (first available network)
Disabled
Network Type
Infrastructure
Transmission Speed
Country/Region
Operating Mode
Data Rate
Autoa
United States (varies by region)
g and b, up to 54 Mbps
up to 54 Mbps
a. Maximum wireless signal rate (IEEE Standard 802.11n draft specification). Actual throughput will vary.
Network conditions and environmental factors, including volume of network traffic, building materials and
construction, and network overhead, lower actual data throughput rate.
33
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
Technical Specifications
This table below describes technical specifications for the NETGEAR 54 Mbps Wireless USB2.0
Adapter WG111v2.
Antennas
Standards
Radio Data Rate
Frequency
LED
Printed internal antenna
802.11g, 802.11b
1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps (Auto Rate Sensing)
2.4GHz to 2.5GHz CCK and OFDM Modulations
Single LED
-- sold indicates connected to network
-- blinking indicates attempting to connect to network
Power
5V bus powered
Emissions
FCC Part 15 Class B, CE
USB 2.0
Bus interface
Provided drivers
Operating Environment
Encryption
Microsoft Windows 2000, XP, and Vista
Operating temperature: 0 to 45 degree C
40-bit (also called 64-bit) and 128-bit WEP data encryption, WPA2-PSK,
and WPA-PSK
Warranty
Limited 1-year warranty
34
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Documents
This appendix provides links to reference documents you can use to gain a more complete
understanding of the technologies used in your NETGEAR product.
Document
Link
Windows XP and Vista
Wireless Configuration
Utilities
Internet Networking and
TCP/IP Addressing
Preparing a Computer for
Network Access
(VPN)
Glossary
35
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
36
v3.0, January 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
|