Milan Technology Switch MIL S500 User Manual

MIL-S500 User’s Guide  
5-Port 10/100 Switch  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To Contact MiLAN Technology  
For prompt response when calling for service information, have the following information  
ready:  
Product serial number and revision. Date of purchase and Vendor or place of purchase.  
You can reach MiLAN Technology  
technical support at: E-mail:  
Telephone: +1.408.744.2751  
Fax: +1.408.744.2771  
©Copyright 2004 MiLAN Technology  
MiLAN Technology  
1329 Moffett Park Dr  
Sunnyvale, CA 94089-1138  
United States of America  
Telephone: +1.408.744.2775  
Fax: +1.408.744.2793  
P/N 90000200 Rev C  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
MIL-S500 Switch  
User’s Guide  
Introduction  
The MIL-S500 Switch provides wire-speed, Fast Ethernet switching function  
that allows high-performance, low cost connections to full-duplex, half-duplex,  
10Mbps and 100Mbps Ethernet network. The MIL-S500 switch provides five  
auto-sensing 10/100Mbps RJ-45 ports that automatically detects the speed of  
the device that is plugged into it. This switching function allows 10Mbps,  
100Mbps, full-duplex and half-duplex devices to communicate on the same  
network without having to replace any infrastructure.  
Key Features  
Compliant with IEEE 802.3 & 802.3u standards  
Auto-negotiation for 10/100Mbps transmission  
Store-and-Forward switching architecture  
Auto-detect of full/half-duplex mode in all ports  
Back-pressure for Half-duplex , Pause frame for Full-duplex  
Plug-and-Play configuration auto addresses learning  
Embedded 1K-entry MAC address table and 1Mega Byte frame buffer  
LED-indicators for power, speed 100Mbps, link/activity  
Space-saving compact size  
Broadcast Storm protection  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDI/MDIX Auto-recognition (No cross over cable required)  
Magnets provide easy installation in modular office  
Package Contents  
Your package contents should include the following:  
MIL-S500 Switch  
Four rubber feet with adhesive pads  
Figure 2. Package Content  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
If any of these pieces are found missing or damaged, please contact your  
local dealer or reseller for replacement.  
Hardware Description  
The Front Panel  
The front panel consists of LED Indicators.  
Figure 3. Front view of MIL-S500 Switch  
LEDs  
Per Device  
Per Port  
Power  
100Mbps ( Link on 100Mbps )  
LINK/ACT ( Link/Activity )  
The Rear Panel  
The rear panel of the MIL-S500 Switch has a DC power connector and 5  
auto-sensing ports.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 4. Rear panel view of the MIL-S500 switch  
Auto-sensing ports for speed and Duplex  
Five Auto-sensing RJ-45 ports for 10Base-T or 100Base-TX connections.  
DC Power Connector  
Plug this connector female end into this device, and the male into a power  
outlet. Supported input voltages 9 VDC at 700 mA.  
Auto-sensing for MDI/MDIX  
No need for crossover  
LED-Indicators  
5
Figure 5. Front panel view of LED indications  
The Table lists the LEDs available and their respective function.  
LED  
Status  
On  
Color  
Green  
Green  
Description  
Power  
The hub is supplied with suitable power.  
The port is connecting with 100Mbps.  
On  
The connection between the hub and the device is  
10Mbps, if the LINK/ACT light is on.  
100Mbps  
Off  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
The port is successfully connecting with the  
device.  
On  
Blinking  
Off  
Green  
The port is receiving or transmitting data.  
LINK/ACT  
The port does not link successfully with the device.  
Installation  
Apply self-adherent rubber feet to the bottom of the Switch near each of the four corners.  
6
See Figure 6.  
If applying Switch to metal surface, install magnets as shown in Figure 6. Switch may  
then be installed on a metal surface.  
Plug in power adapter.  
Trouble Shooting  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Switch can be easily monitored through panel indicators that assist in the  
identification of problems. This section describes common problems you may  
encounter and where you can find possible solutions.  
Power  
If the power indicator does not turn on when the power cord is plugged in, you  
may have a problem with the power outlet, or power cord. However, if it  
powers off after running for a while, check for loose power connections, power  
losses or surges at the power outlet. Or, you may try to unplug the power cord  
on the Switch, wait for five seconds and then reconnect. If you still cannot  
resolve the problem, call our technical support hotline.  
Cabling  
Verify that the cabling type is correct. Be sure all cable connectors are securely seated  
in the required ports. Use all standard unshielded twisted-pair (UTP), Category 3, 4, or  
5 cables or Category 5 only when connecting with Fast Ethernet. Make sure the  
maximum distance between the Switch to the workstation, or Switch is 100 meters.  
Product Specification  
General Specification  
IEEE 802.3 10Base-T Ethernet  
Standard Compliance  
IEEE 802.3u & 802.3x 100Base-TX Fast Ethernet  
Number of Ports  
5X 10/100Mbps Auto-sensing RJ-45 ports  
Ethernet: 10Mbps(half duplex)  
20Mbps(full duplex)  
Fast Ethernet: 100Mbps(half duplex)  
200Mbps(full duplex)  
Data Transfer Rate  
Network Cables  
Topology  
Unshielded twisted-pair cable  
Star  
LED Indicators  
Per Device  
Per Port  
Power  
100Mbps, LINK/ACT  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Performance Specification  
Transmission Method  
Store and forward  
MAC address table  
Maximum Forwarding  
Rate(64byte packets)  
Maximum Filtering  
1K-entry MAC address table  
14,880 pps /10 BASE-T  
148,800 pps /100BASE-TX  
14,880 pps /10BASE-T  
Rate(64byte packets)  
148,800 pps/100BASE-TX  
Pause frame (Full-duplex)  
Back-pressure (Half-duplex)  
Flow control  
Duplex mode  
Supports both half-duplex and full-duplex mode  
Physical & Environmental Specification  
Power Supply  
Dimensions  
External power adapter,  
DC 9V, 700mA  
111mm×70mm×20mm (L×W×H)  
Operating temperature:  
0 to 45 (32 to 113)  
storage temperature:  
40 to 70 (-22 to 140)  
10% to 90% (non-conditioning)  
FCC Class B, CE mark  
UL, cUL  
Temperature  
Humidity  
EMI  
Safety  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P/N 90000200 Rev C  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Dishwasher G 851 SC Plus User Manual
MTD Snow Blower Attachment 190 822 User Manual
Newcon Optik Hunting Equipment NC 3 12X50 User Manual
Nikon Camera Accessories EN EL8 User Manual
Nokia Cell Phone 1200 User Manual
Nortel Networks Switch 8691SF User Manual
Omron Printer NT631 User Manual
Oregon Scientific MP3 Player VR383 User Manual
Panasonic Answering Machine KX F2710NZ User Manual
Panasonic Camcorder AG HVX200A User Manual