METROLOGIC INSTRUMENTS, INC.
MS7120 Series Fixed Projection
Laser Scanner
Installation and User’s Guide
MLPN 2408
Printed in USA
December 1998
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Scanner and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operational Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Scanner Installation: Powered by External Power Supply . . . . . . . . . . . . . . . 5
Scanner Installation: Powered by the Host Device . . . . . . . . . . . . . . . . . . . . . 6
Scanner Installation: to the PC for the Scanner with built-in
PC Keyboard Wedge Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Scanner Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Audible Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Failure Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Visual Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Depth of Field Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Optimal Low Density Depth of Field . . . . . . . . . . . . . . . . . . . . . . 13
Optimal High Density Depth of Field . . . . . . . . . . . . . . . . . . . . . . 13
Close Depth of Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Normal Depth of Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Far Depth of Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Minimum Bar Code Element From Scanner Face . . . . . . . . . . . . . . . . . . . . 16
Optimal Low Density Depth of Field . . . . . . . . . . . . . . . . . . . . . . . 16
Optimal High Density Depth of Field . . . . . . . . . . . . . . . . . . . . . . 17
Close Depth of Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Normal Depth of Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Far Depth of Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-26
RS-232 Demonstration Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Application and Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents (continued)
Appendix A
Design Specifications
29, 30
31-35
36-38
Appendix B
Default Settings
Appendix C
Pin Assignments
Appendix D
Warranty and Disclaimer 39, 40
Appendix E
Notices
41, 42
43, 44
Index
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Orbit™ is an aggressive, omnidirectional laser bar code scanner. Light-weight
and rugged, Orbit is small in size, but BIG in performance. Designed for
applications where counter space is limited, Orbit is the ideal presentation
scanner for retail, convenience, liquor and specialty stores. In addition, Orbit’s
unique, contoured shape allows it to be picked-up and used as a hand-held
scanner when scanning large or bulky items.
Engineered with a large, easy-to-find optimal scan area, Orbit increases the
first pass read rate for maximum productivity. The scanning head can be tilted
vertically a full 30o for added flexibility when scanning various sized objects.
These features increase the scanning throughput without increasing the
scanner size.
SCANNER
7120-41
INTERFACE
Full RS-232C and Light Pen Emulation
7120-47
Keyboard Wedge, Stand-Alone Keyboard and
RS-232 Transmit/Receive
7120-9
7120-11
7120-67
OCIA and RS-232 Transmit/Receive
IBM 46XX/RS-232C
Full RS-232C and Light Pen Emulation
Orbit offers a great deal of features to the consumer:
‚
‚
‚
‚
‚
‚
Fully automatic scanning operation
PowerLink compatible
Data editing
7 beeper tones
Programmable depth of field
Easy programming
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanner and Accessories
The following is a list of the parts included in the MS7100 kit.
!
!
MS7120 Laser Scanner - Refer to page 28 for available
communication protocols
Power Transformer AC in 120V, 220V- 240V Continental
European or 220V- 240V UK. DC in regulates 5.2V@650mA
(MLPN45593/45591/45592)
RS-232, Light Pen, OCIA and 46xx scanners:
!
PowerLink cable with built in power jack:
Standard - MLPN 54xxx* - 2.1m (7') straight cord, short strain relief
or
Optional - MLPN 53xxx* - 2.7m (9') coiled cord, long strain relief
*xxx specifies connection to the host
Keyboard Wedge Scanners:
!
!
Keyboard Wedge PowerLink Cable with a 5-pin
DIN female connector and a 6-pin mini DIN male
connector (MLPN 19763)
Adapter Cable with a 5-pin DIN male
connector and a 6-pin mini DIN female
connector (MLPN 19716)
Available on the Metrologic Website (www.metrologic.com):
!
!
MetroSelect Programming Guide (MLPN 2407)
MS7120 User’s and Installation Guide (MLPN 2408)
Options
!
Counter/Wall Mount Kit (MLPN 45619)
Other items may be ordered for the specific protocol being used. To order additional
items, contact the dealer, distributor or call Metrologic’s Customer Service Depart-
ment at 1-800-ID-METRO or 1-800-436-3876.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
1.) Plug in the scanner. When the MS7120 is ready to scan,
the green LED will turn on, then the red LED will flash
and the scanner will beep once. (the red LED will
remain on for the duration of the beep).
2.) The scanner is shipped from the factory programmed with
default settings. To configure the MS7120 scanner to
meet the host system’s specific needs, refer to the Metro-
Select Programming Guide (MLPN 2407) for instructions
on how to enter the program mode and to select the
appropriate bar codes.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operational Test
Metrologic recommends using the external power supply provided with the
scanner when operating the MS7120. When using power supplied by the host,
the host system should supply a minimum of 250 mA of current @ 5VDC.
Keyboard Wedge Scanners:
1. Connect the 10-pin modular plug of the PowerLink cable into the
scanner jack. Connect the other end of the PowerLink Y-type cable
to the PC. Connect the 5-pin female DIN side of the Y-type cable
into the keyboard connector on the PC and connect the 6-pin male
mini-DIN side into the PC.
2. Check the AC input requirements of the power supply to make sure the
voltage matches the AC outlet. Connect AC power to the transformer.
3. Listen for a single beep that indicates the scanner is ready for use.
(steady green LED and the red LED will flash once)
RS-232, Light Pen, OCIA and 46xx scanners:
1. Connect the 10-pin modular plug of the PowerLink cable into the scanner
jack. Connect the other end of the PowerLink cable (the 9-pin D-type
connector) to the PC.
2. Check the AC input requirements of the power supply to make sure the
voltage matches the AC outlet. Connect AC power to the transformer.
3. Listen for a single beep that indicates the scanner is ready for use.
(steady green LED and the red LED will flash once)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanner Installation: Powered by External Power Supply
To maintain compliance with applicable standards, all circuits connected to the
scanner must meet the requirements for SELV (Safety Extra Low Voltage)
according to EN 60950.
1. Turn off the host system.
2. Make the necessary PowerLink cable connections to the scanner and
the host.
3. Connect the external transformer into the power jack on the Power Link
cable.
4. Check the AC input requirements of the power supply to make sure the
voltage matches the AC outlet. (the socket-outlet shall be installed near
the equipment and shall be easily accessible.) Connect AC power to the
transformer.
5. Turn on the host system.
NOTE:
a. When the scanner first receives power, the green LED will
turn on. Then the scanner will beep once and the red LED
will flash simultaneously.
b. Plugging the scanner into the serial port of the PC does not
guarantee that scanned information will appear at the PC. A
software driver and correct configuration setting are also
required for proper communication to occur.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanner Installation: Powered by Host Device
The MS7120 scanner interfaces terminate to a 10-pin modular jack. Connect
the 10-pin modular plug of the PowerLink cable into the jack then connect the
other end of the PowerLink cable to the host. Refer to Appendix C page 36 for
pin assignments.
1. Turn off the host system.
2. Make the necessary PowerLink cable connections to the scanner and the
host.
3. Turn on the host system.
NOTE:
a. When the scanner first receives power, the green LED will turn
on. Then the scanner will beep once and the red LED will
flash simultaneously.
b. Plugging the scanner into the serial port of the PC does not
guarantee that scanned information will appear at the PC. A
software driver and correct configuration setting are also
required for proper communication to occur.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanner Installation to the PC for the Scanner with Built-in
PC Keyboard Wedge Interface
To maintain compliance with applicable standards, all circuits connected to the
scanner must meet the requirements for SELV (Safety Extra Low Voltage)
according to EN 60950.
1. The MS7120 Keyboard Wedge scanner interface terminates to a 10-pin
modular jack. Connect the 10-pin modular plug of the PowerLink cable
into the jack. The Power Link cable is terminated with a 5-pin DIN
female connector on one end, and a 6-pin mini DIN male on the other.
Metrologic will supply an adapter cable with a 5-pin DIN male
connector on one end and a 6-pin mini DIN female connector on the
other. According to the termination required, connect the appropriate
end of the adapter cable to the PowerLink cable, leaving the necessary
termination exposed for connecting to the keyboard and the keyboard
port on the PC. Refer to Appendix C page 38 for pin assignments.
2. If the PC is on, exit the application and turn the PC off.
3. Disconnect the keyboard from the PC.
4. Connect the scanner as described in step 1. Connect the external
transformer into the power jack on the Power Link cable. Refer to
Manufacturer’s Recommendation below. Connect AC power to the
transformer.
5. Power up the PC.
Manufacturer’s Recommendation:
Metrologic recommends the use of an external power supply with MS7120-47
Keyboard Wedge applications. Powering the MS7120-47 directly from the com-
puter keyboard connector could interfere with the operation of the scanner or the
computer. Not all computers supply the same current through the keyboard port,
this explains why a scanner would work on one computer and not another.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanner Parts
Green and Red LEDs: During normal operation, the green
LED is on. This indicates that the laser is on and the unit is
ready to scan. On a successful read of a bar code, the red LED
will turn on. After communication to the host is complete, the
red LED will turn off. The LEDs are also used as diagnostic
indicators and mode indicators. Refer to pages 9-11 for details.
ú
Orbit Face:
Tilts 30o vertically
þ
for variable position-
ing of the scan pattern.
Output Window:
Laser light emits
º
from this aperture.
ü
Cable Connection:
The MS7120 scanner
has a 10-pin modular
jack. The 10-pin
modular plug on the
PowerLink cable
connects into the
MS7120 jack. Refer to
pages 5-7 for specific
protocol PowerLink
cable connections.
Side View
Top View
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Audible Indicators
When the MS7120 scanner is in operation, it provides audible feedback.
These sounds indicate the status of the scanner. Eight settings are available for
the tone of the beep (normal, 6 alternate tones and no tone). To change the
tone, refer to the MetroSelect Programming Guide MLPN 2407.
One Beep
*
When the scanner first receives power, the green LED will turn
on, then the red LED will flash and the scanner will beep once.
(The red LED will remain on for the duration of the beep.) The
scanner is now ready to scan.
When the scanner successfully reads a bar code, the red LED
will flash and the scanner beeps once (if programmed to do so).
If the scanner does not beep once and the red light does not
flash, then the bar code has not been successfully read.
Razzberry Tone
This is a failure indicator. Refer to failure modes page 10.
Three Beeps - during operation
* * *
During operation of the scanner, the red LED will flash while
the scanner simultaneously beeps three times (while going into
programming mode).
The red LED will continue to flash until the unit exits program
mode. Upon exiting program mode, the scanner will beep three
times and the red LED will stop flashing. When configured, 3
beeps can also indicate a communications timeout during normal
scanning mode.
When using one-code-programming, the scanner will beep
three times (the current selected tone), followed by a short
pause then by a high tone and a low tone. This tells the user
that the single configuration bar code has successfully con-
figured the scanner.
Three Beeps - on power up
This is a failure indicator. Refer to failure modes page 10.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Failure Modes
Flashing Green and One Razzberry Tone
This indicates the scanner has experienced a laser
subsystem failure. Return the unit for repair at an
authorized service center.
Flashing Red and Green and Two Razzberry
Tones
This indicates the scanner has experienced a motor
failure. Return the unit for repair at an authorized
service center.
Continuous Razzberry Tone with both LEDs off
If, upon power up, the scanner emits a continuous razz-
berry tone, then the scanner has an electronic failure.
Return the unit for repair at an authorized service
center.
Three Beeps - on power up
* * *
If the scanner beeps 3 times on power up then, the non-
volatile memory that holds the scanner configuration
has failed. Return the unit for repair at an authorized
service center.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Visual Indicators
There are a red LED and a green LED on the head of the Orbit MS7120.
When the scanner is on, the flashing or stationary activity of the LEDs
indicates the status of the current scan and the scanner.
No Red or Green LED
The LEDs will not be illuminated if the scanner is not receiving
power from the host or transformer.
Steady Green
When the laser is active, the green LED is illuminated. The green
LED will remain illuminated until the laser is deactivated.
During the power save mode, the laser will turn on and turn off.
During this period, the green LED remains illuminated.
Steady Green and Single Red Flash
When the scanner successfully reads a bar code, the red LED will
flash and the scanner will beep once. If the red LED does not flash
or the scanner does not beep once, then the bar code has not been
successfully read.
Steady Green and Steady Red
After a successful scan, the scanner transmits the data to the host
device. Some communication modes require that the host inform the
scanner when data is ready to be received. If the host is not ready to
accept the information, the scanner’s red LED will remain on until
the data can be transmitted.
Steady Green and Flashing Red
This indicates the scanner is in program mode. A razzberry tone
indicates that an invalid bar code has been scanned in this mode.
Steady Red, Green off
This indicates the scanner may be waiting for communication from
the host.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Labels
Each scanner has labels on the bottom of the unit. One label contains
information such as the model number, date of manufacture, serial number and
notes that the device is a Class IIa laser product. The other label states the
device is an LASERKLASSE 1 product. The following are examples of these
labels:
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth of Field Specifications
(based on 100% UPC bar codes)
Optimal Low Density Depth of Field (default)
Optimal High Density Depth of Field
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth of Field Specifications (continued)
(based on 100% UPC bar codes)
Close Depth of Field
Normal Depth of Field
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth of Field Specifications (continued)
(based on 100% UPC bar codes)
Far Depth of Field
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth of Field by Minimum Bar Code Element Width
Optimal Low Density Depth of Field (default)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth of Field by Minimum Bar Code Element Width
(continued)
Optimal High Density Depth of Field (default)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth of Field by Minimum Bar Code Element Width
(continued)
Close Depth of Field
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth of Field by Minimum Bar Code Element Width
(continued)
Normal Depth of Field
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth of Field by Minimum Bar Code Element Width
(continued)
Far Depth of Field
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Smudges and dirt can interfere with the proper scanning of a bar code.
Therefore, the output window will need occasional cleaning.
1. Spray glass cleaner onto lint free, non-abrasive cleaning cloth.
2. Gently wipe the scanner window.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
The following guide is for reference purposes only. Contact a Metrologic
representative at 1-800-ID-METRO or 1-800-436-3876 to preserve the
limited warranty terms on page 39.
All Interfaces
MS7120 Series Troubleshooting Guide
SYMPTOMS
POSSIBLE CAUSE(S)
SOLUTION
No LEDs, beep
or motor spin
No power is being supplied Check transformer, outlet and power
to the scanner
strip. Make sure the cable is plugged
into the scanner
No LEDs, beep
No power is being supplied Some host system’s cannot supply
to the scanner from host
Non-volatile RAM failure
RAM or ROM failure
VLD failure
enough current to power Orbit. Use
the power supply included with the
scanner.
3 beeps on
power up
Contact a Metrologic Representative,
if the unit will not hold the
programmed configuration
Continuous razz
tone on power
up
Contact a Metrologic Representative,
if the unit will not function
Razz tone and
green LED flash
at power up
Contact a Metrologic Representative
Contact a Metrologic Representative
Razz tone and
both LEDs flash
at power up
Scanner motor failure
Unit scans,
Communicates
and beeps twice
Same symbol timeout set
too short
Adjust same symbol timeout for a
longer time
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide (continued)
SYMPTOMS
POSSIBLE CAUSE(S)
SOLUTION
The unit powers
up, but does not
scan and/or beep
Beeper disabled. No tone
selected
Enable beeper. Select tone
The unit powers
up, but does not
scan and/or beep
Scanning a particular
symbology that is not
enabled
UPC/EAN, Code 39, interleaved 2 of
5, Code 93, Code 128 and Codabar
are enabled by default. Verify that the
type of bar code being read has been
selected
The unit powers
up, but does not
scan and/or beep
The scanner has been
programmed for a
Verify that the bar code that is being
scanned falls into the criteria. (Typical
of Non-UPC/EAN codes.) (The
scanner defaults to a minimum of 4
character bar code)
character length lock, or a
minimum length and bar
code being scanned does
not satisfy the programmed
criteria
The unit scans a
bar code, but
The scanner is configured
to support some form of
If the scanner is setup to support
ACK/NAK, RTS/CTS, XON/XOFF or
locks up after the host handshaking but is not D/E, verify that the host cable and host
first scan (red
LED stays on)
receiving the signal
are supporting the handshaking
properly
The unit scans,
but the data
transmitted to
the host is
The scanner’s data format
does not match the host
system requirements
Verify that the scanner’s data format
matches that required by the host.
Make sure that the scanner is
connected to the proper host port
incorrect
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide (continued)
SYMPTOMS
POSSIBLE CAUSE(S)
SOLUTION
Scanner beeps at
some bar codes
and NOT for
others of the
The print quality of the bar
code is suspect
Check print mode. The type of printer
could be the problem. Change print
settings. For example change to econo
mode or high speed
same bar code
symbology
Scanner beeps at
some bar codes
and NOT for
others of the
The aspect ratio of the bar
code is out of tolerance
Check print mode. The type of printer
could be the problem. Change print
settings. ie change to econo mode or
high speed
same bar code
symbology
Scanner beeps at
some bar codes
and NOT for
others of the
The bar code may have
been printed incorrectly
Check if it is a check digit/character/or
border problem
same bar code
symbology
Scanner beeps at
some bar codes
and NOT for
others of the
The scanner is not
configured correctly for
this type of bar code
Check if check digits are set properly
same bar code
symbology
Scanner beeps at
some bar codes
and NOT for
others of the
The minimum symbol
length setting does not
work with the bar code
Check if the correct minimum symbol
length is set
same bar code
symbology
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide (continued)
Keyboard Wedge Only
SYMPTOMS
POSSIBLE CAUSE(S)
SOLUTION
The unit scans
the bar code but
there is no data
Configuration is not
correct
Make sure the scanner is configured
for the appropriate mode. Check
internal jumper
The unit scans
but the data is
not correct
Configuration is not
correct
Make sure that the proper PC type AT,
PS2 or XT is selected. Verify correct
country code and data formatting are
selected. Adjust intercharacter delay
SYMPTOM
The unit is
transmitting
each character
Configuration is not
correct
Increase the interscan code delay
setting. Adjust whether the F0 break is
transmitted. It may be necessary to try
this in both settings.
Alpha characters
show as lower
case
Computer is in Caps Lock
mode
Enable Caps Lock detect setting of the
scanner to detect whether the PC is
operating in Caps Lock
Everything
works except for
a couple of
These characters may not
be supported by that
country’s key look up table
Try operating the scanner in Alt mode
characters
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide (continued)
RS-232 only
SYMPTOMS
POSSIBLE CAUSE(S)
SOLUTION
Power-up OK
and scans OK
but does not
communicate
properly to the
host
Com port at the host is not
working or configured
properly
Check to make sure that the baud rate
and parity of the scanner and the
communication port match and the
program is looking for “RS-232" data
Power-up OK
and scans OK
but does not
communicate
properly to the
host
Cable not connected to the
proper com port
Check to make sure that the baud rate
and parity of the scanner and the
communication port match and the
program is looking for “RS-232" data
Power-up OK
and scans OK
but does not
communicate
properly to the
host
Com port not operating
properly
Check to make sure that the baud rate
and parity of the scanner and the
communication port match and the
program is looking for “RS-232" data
The host is
receiving data
but the data does same interface font
not look correct
The scanner and host may
not be configured for the
Check that the scanner and the host
are configured for the same interface
font
Characters are
being dropped
Intercharacter delay needs
to be added to the
transmitted output
Add some intercharacter delay to the
transmitted output by using the
MetroSelect Programming Guide
MLPN 2407
26
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 Demonstration Program
If an RS-232 scanner is not communicating with your IBM compatible PC, key in the
following BASIC program to test that the communication port and scanner are working.
This program is for demonstration purposes only. It is only intended to prove that cabling
is correct, the com port is working, and the scanner is working. If the bar code data
displays on the screen while using this program, it only demonstrates that the hardware
interface and scanner are working. At this point, investigate whether the application
software and the scanner configuration match. If the application does not support RS-232
scanners, a software wedge program that will take RS-232 data and place it into a
keyboard buffer may be needed. This program tells the PC to ignore RTS-CTS, Data Set
Ready (DSR) and Data Carrier Detect (DCD) signals. If the demonstration program
works and yours still does not, jumper RTS to CTS and Data Terminal Reading (DTR) to
DCD and DSR on the back of your PC.
10
CLS
20
30
35
ON ERROR GOTO 100
OPEN “COM1:9600,S,7,1,CS0,DS0,CD0,LF” AS #1
PRINT “SCAN A FEW BAR CODES”
LINE INPUT #1, BARCODE$
40
50
60
70
100
110
PRINT BARCODE$
K$ = INKEY$: IF K$ = CHR$(27) THEN GOTO 32766
GOTO 40
PRINT “ERROR NO.”; ERR; “ PRESS ANY KEY TO TERMINATE.”
K$ = INKEY$: IF K$ = “” THEN GOTO 110
32766 CLOSE: SYSTEM
32767 END
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Applications and Protocols
The model number on each scanner includes the scanner number and
communications protocol.
Scanner Version Identifier Communication Protocol(s)
7120
7120
41
47
Full RS-232C and Light Pen Emulation
Keyboard Wedge, Stand-Alone Keyboard
and RS-232 Transmit/Receive
OCIA and RS-232 Transmit/Receive
IBM 46XX and Full RS-232C
Full RS-232C
7120
7120
7120
9
11
67
The MS7120 Hand-Held Laser Scanner with Built-in PC Keyboard
Wedge Interface is designed to be used for keyboard emulation only. However,
many RS-232 programmable functions that are available
in other Metrologic scanners are also available as keyboard wedge functions.
The most important selectable options specific to the key-
board wedge are the following:
Keyboard Type
!
!
!
** AT (includes IBM® PS2 models 50, 55, 60, 80)
XT
IBM PS2 (includes models 30, 70, 8556)
Keyboard Country Type
!
!
!
!
** USA
French
Italian
!
!
!
!
United Kingdom
German
Spanish
Belgium
Swiss
**Default setting. Refer to Appendix B pages 31-35 for default settings.
Refer to the MetroSelect Programming Guide (MLPN 2407) for infor-
mation on how to change the default settings.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Design Specifications
Operational
Light Source:
Depth of Field:
(programmable)
Scan Speed:
VLD 675 ± 5nm, 0.681 milliwatts (PEAK)
0 mm to 215 mm (0" to 8.5") at default
1200 scans/second
Scan Pattern:
Scan Lines:
5 fields of 4 parallel lines (omnidirectional)
20
Min Bar Width:
Decode Capability:
0.13 mm (5.2 mil)
Autodiscriminates all standard bar codes;
for other symbologies call Metrologic
PC Keyboard Wedge, RS-232, OCIA, Light Pen,
IBM 46xx, Stand Alone PC Keyboard
35% minimum reflectance difference
up to 80 data characters
System Interfaces:
Print Contrast:
No. Characters Read:
(Maximum number will vary based on symbology
and density)
Roll, Pitch, Yaw:
Beeper Operation:
Indicators (LED):
360E, 60E, 60E
7 tones or no beep
green = laser on, ready to scan
red = good read, decoding
Mechanical
Height:
150 mm (5.9")
Depth:
105 mm (4.1")
Width-Orb:
Width-Base:
Weight:
Termination:
Cable:
80 mm (3.1")
102 mm (4.0")
380 grams (13.4 oz.)
10-pin modular RJ45
Standard 2.1 m (7') straight; optional 2.7 m (9')
coiled; for other cables call Metrologic
30N vertical
Tilt - Orb:
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A (continued)
Electrical
Input Voltage:
Power :
5.2VDC ± 0.25V
1.1 W
Operating Current :
DC Transformers:
Laser Class:
225 mA
Class II; 5.2 V @650 mA
CDRH: Class IIa; EN 60 825-1: 1994/A11:1996
Class 1
EMC:
FCC Class A, CISPR Class A
Environmental
Operating Temperature: 0EC to 40EC (32EF to 104EF)
Storage Temperature:
Humidity:
Light Levels:
Shock:
Contaminants:
Ventilation:
-40EC to 60EC (-40EF to 140EF)
5% to 95% relative humidity, non-condensing
4840 LUX (450 foot candles)
Designed to withstand 1 m (3.1') drops
Sealed to resist airborne particulate contaminants
None required
Specifications subject to change without notice.
This METROLOGIC product may be covered by one or more of the following
U.S. Patents:
U.S. Patent No. 5,081,342; 5,216,232; 5,340,971; 5,525,789; 5,557,093;
5,627,359; 5,637,852
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Default Settings
Many functions of the scanner can be "programmed" - that is, enabled or
disabled. The scanner is shipped from the factory programmed to a set of
default conditions. The default parameter of the scanner has an asterisk ( * ) in
the charts on the following pages. If an asterisk is not in the default column
then the default setting is Off or Disabled. Every communication does not
support every parameter. If the communication supports a para-meter listed in
the charts on the following pages, a check mark will appear.
Parameter
Default
OCIA
RS-
232*
Light
Pen
IBM
46XX
KBW
UPC/EAN
*
*
*
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Code 128
Code 93
Codabar
Interleaved 2 of 5 (ITF)
MOD 10 Check on ITF
Code 11
*
*
Code 39
Full ASCII Code 39
MOD 43 Check on Code 39
MSI-Plessey
T
T
T
T
T
T
T
T
T
T
MSI-Plessey 10/10 Check
Digit
MSI-Plessey MOD 10 Check
Digit
*
T
T
T
T
T
Paraf Support
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
ITF Symbol Lengths
Minimum Symbol Length
Symbol Length Lock
Bars High as Code 39
Spaces High as Code 39
Bars High as Scanned
Spaces High as Scanned
DTS/SIEMENS
Variable
4
None
*
T
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B (continued)
Parameter
Default
*
OCIA
RS-
232*
Light
Pen
IBM
46XX
KBW
DTS/NIXDORF
NCR F
T
T
T
NCR S
Poll Light Pen Source
Beeper Tone
T
T
T
Normal
T
T
T
T
T
T
T
T
Beep/Transmit Sequence
Before
Transmit
Communication Timeout
Razzberry Tone on Timeout
Three Beeps on Timeout
No Beeps on Timeout
None
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
*
Enter Power Save Mode
10 mins.
Same Symbol Rescan
Timeout: 200 msecs
Same Symbol Rescan Timeout:
500 msecsProgrammable in 50
msec steps(MAX 6.35 seconds)
*
T
T
T
T
T
Same Symbol Rescan
Timeout: 1250 msecs
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Same Symbol Rescan
Timeout: 2000 msecs
Intercharacter Delay
Programm able in 1 msec steps
(MAX 255 msecs)
1 msecs
10msecs
in KBW
Number of Scan Buffers
Transmit UPC-A Check Digit
Transmit UPC-E Check Digit
Expand UPC-E
1
*
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Convert UPC-A to
EAN-13
Transmit Lead Zero on UPC-E
Convert EAN-8 to EAN-13
T
T
T
T
T
T
T
T
T
T
T
T
T
Transmit UPC-A Number
System
*
*
T
T
Transmit UPC-A
Manufacturer ID#
T
T
T
T
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B (continued)
Parameter
Default
*
OCIA
RS-
232*
Light
Pen
IBM
46XX
KBW
Transmit UPC-A Item ID#
T
T
T
T
T
T
T
T
T
Transmit Codabar
Start/Stop Characters
CLSI Editing (Enable)
T
T
T
T
T
T
T
T
Transmit Mod 43 Check Digit
on Code 39
Transmit Code 39
T
T
T
T
Stop/Start Characters
Transmit Mod 10/ITF
T
T
T
T
T
T
T
T
Transmit MSI-Plessey Check
Characters
Parity
Space
9600
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Baud Rate
8 Data Bits
7 Data Bits
*
Transmit Sanyo ID Characters
Nixdorf ID
T
T
T
T
T
T
T
T
T
T
LRC Enabled
UPC Prefix
UPC Suffix
Transmit AIM ID Characters
STX Prefix
ETX Suffix
Carriage Return
*
*
Line Feed - disabled by default
in KBW
Tab Prefix
T
T
T
T
T
Tab Suffix
"DE" Disable Command
"FL" Laser Enable Command
DTR Handshaking Support
RTS/CTS Handshaking
T
T
T
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B (continued)
Parameter
Default
*
OCIA
RS-
232*
Light
Pen
IBM
46XX
KBW
Character RTS/CTS
Message RTS/CTS
XON/XOFF Handshaking
ACK/NAK
T
T
T
T
Two Digit Supplements
Five Digit Supplements
Bookland
T
T
T
T
T
T
T
T
as code
39
T
T
T
T
T
T
T
T
as code
39
as code
39
977 (2 digit) Supplemental
Requirement
T
Supplements are not Required
Two Digit Redundancy
*
*
T
T
T
T
T
T
T
T
T
T
Five Digit Redundancy
T
T
T
T
T
T
T
T
T
T
100 msec to Find Supplement
Programmable in 100msec
steps (MAX 800 msec)
*
Coupon Code 128
T
T
T
as code
39
T
T
T
T
Programmable Code Lengths
7 aval.
T
T
T
Programmable Prefix
Characters
10 avail.
Suffix Characters
T
T
Prefixes for individual Code
Types
Editing
T
T
T
T
T
Inter Scan-Code Delay Pro-
gram mable (100 msec steps)
800 msec
1 msec
*
Function/Control Key Support
Minimum Element WidthPro-
grammable in 5.6 Fsec steps
T
T
Depth of Field
Variable Depth of Field
T
T
T
T
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B (continued)
Parameter
Default
*
OCIA
RS-
232*
Light
Pen
IBM
46XX
KBW
Normal Depth of Field
T
T
T
T
T
Extended Depth of Field
Long Depth of Field
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Ultra Close Depth of Field
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Pin Assignments
Pin Assignments for the PowerLink Cable
The MS7120 scanner interfaces terminate to a 10-pin modular jack.
Connect the 10-pin modular plug of the PowerLink cable into the jack
then connect the other end of the PowerLink cable to the host. (Refer to
page 6 for details). Due to the variations in current supplied by the many
available PC’s, Metrologic suggests the use of an external power supply.
“9" OCIA
“11" IBM 46XX/RS-232*
PIN FUNCTION
PIN FUNCTION
1
2
3
4
5
6
7
8
9
Ground
1
2
3
4
5
6
7
8
9
Ground
RS-232 Transmit Output
RS-232 Receive Input
RDATA
RDATA Return
Clock in
Clock out
Clock in Return/Clock out Rtrn
+5VDC
RS-232 Transmit Output
RS-232 Receive Input
RTS Output
CTS Input
DTR Input
IBM 46XX Transmit
IBM 46XX Receive
+5VDC
10 Shield Ground
10 Shield Ground
“67" RS-232/LTPN*
PIN FUNCTION
“41" RS-232/LTPN
PIN FUNCTION
1
2
3
4
5
6
7
8
9
Ground
1
2
3
4
5
6
7
8
9
Ground
RS-232 Transmit Output
RS-232 Receive Input
RTS Output
CTS Input
DTR Input/LTPN Source
Reserved
RS-232 Transmit Output
RS-232 Receive Input
RTS Output
CTS Input
DTR Input/LTPN Source
Reserved
LTPN Data
+5VDC
LTPN Data
+5VDC
10 Shield Ground
10 Shield Ground
*Preliminary
Options listed are program/cable selections
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C (continued)
Pin Assignments for the PowerLink Cable Keyboard Wedge
Interface
The MS7120 Keyboard Wedge scanner interface terminates to a 10-pin
modular jack. Connect the 10-pin modular plug of the PowerLink cable
into the jack then connect the other end of the PowerLink Y-type cable to
the host and keyboard (refer to page 7 for details). Due to the variations
in current supplied by the many available PC’s, Metrologic suggests the
use of an external power supply.
“47" Keyboard Wedge
PIN FUNCTION
1
2
3
4
5
6
7
8
9
Ground
RS-232 Transmit Output
RS-232 Receive Input
PC Data
PC Clock
KB Clock
PC +5V
KB Data
+5VDC
10 Shield Ground
Options listed are program/cable selections
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C (continued)
Pin Assignments for the 5-pin DIN and 6-pin mini-DIN MS7120 Hand-
Held Laser Scanner with Built-in PC Keyboard Wedge Interface
The MS7120 Keyboard Wedge scanner interface terminates to a 10-pin
modular jack. Connect the 10-pin modular plug of the PowerLink cable
into the jack. The Power Link cable is terminated with a 5-pin DIN female
connector on one end, and a 6-pin mini DIN male on the other. Metrologic
will supply an adapter cable with a 5-pin DIN male connector on one end
and a 6-pin mini DIN female connector on the other.
PowerLink Cable Connectors
Adapter Cable Connectors
5-pin Female
6-pin Male
5-pin Male
6-pin Female
According to the termination required, connect the appropriate end of the
adapter cable to the PowerLink cable, leaving the necessary termination
exposed for connecting to the keyboard and the keyboard port on the PC.
The pin assignments are as follows:
5-pin Female DIN
6-pin Male mini-DIN
Pin
Function
Pin
Function
1
2
3
4
5
Keyboard Clock
Keyboard Data
No Connect
Power Ground
+5 Volts DC
1
2
3
4
5
6
Keyboard Data
No Connect
Power Ground
+5 Volts DC
PC Clock
No Connect
5-pin Male DIN
6-pin Female mini-DIN
Pin
Function
Pin
Function
1
2
3
4
5
PC Clock
PC Data
No Connect
Power Ground
+5 Volts DC
1
2
3
4
5
6
Keyboard Data
No Connect
Power Ground
+5 Volts DC
Keyboard Clock
No Connect
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D
Warranty and Disclaimer
Limited Warranty
Products manufactured by Metrologic have a 2-year limited warranty from
date of manufacture.
This warranty is limited to repair, replacement or refund at Metrologic’s
discretion. Faulty equipment must be returned to the Metrologic facility in
Blackwood, New Jersey or Puchheim, Germany. To do this, contact
Metrologic Customer Service/Repair for a Returned Material Authorization
(RMA) number.
In the event that it is determined that the equipment failure is covered under the
warranty, Metrologic shall, as its sole option, repair, replace with a functionally
equivalent unit, or refund an amount equal to the purchase price to the original
purchaser, whether distributor, dealer/reseller, or retail consumer, and return the
equipment to the customer without charge for service or return freight.
This limited warranty does not extend to any Product which, in the sole judge-ment
of Metrologic, has been subjected to misuse, neglect, improper installation or
accident, nor does it extend to any Product which has been repaired or altered by
anyone who is not a Metrologic authorized representative.
THIS LIMITED WARRANTY, EXCEPT AS TO TITLE, IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR PURPOSE, ARISING BY LAW, CUSTOM OR
CONDUCT. THE RIGHTS AND REMEDIES PROVIDED HEREIN ARE EXCLUSIVE
AND IN LIEU OF ANY OTHER RIGHTS OR REMEDIES. IN NO EVENT SHALL
METROLOGIC BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY INJURY TO PROPERTY
OR PERSON OR EFFECT ON BUSINESS OR PROFIT, AND IN NO EVENT SHALL
ANY LIABILITY OF METROLOGIC EXCEED THE ACTUAL AMOUNT PAID TO
METROLOGIC FOR THE PRODUCT.
Metrologic Instruments, Inc.
90 Coles Road
Blackwood, NJ 08012
Customer Service Department
1-800-ID-METRO (1-800-436-3876)
TEL: 609-228-8100
FAX: 609-228-6673
Metrologic Instruments GmbH
Dornierstrasse 2
82178 Puchheim b.
Munich, Germany
TEL: 49-89-89019-0
FAX: 49-89-89019-200
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D (continued)
Disclaimer
Metrologic Instruments, Inc. and the author or authors make no claims or warranties with respect
to the contents or accuracy of this publication, or the product it describes, including any warranties
of fitness or merchantability for a particular purpose. Any stated or expressed warranties are in
lieu of all obligations or liability for any damages, whether special, indirect, or consequential,
arising out of or in connection with the use of this publication or the product it describes.
Furthermore, the right is reserved to make any changes to this publication without obligation to
notify any person of such changes. Metrologic also reserves the right to make any changes to the
product described herein.
Exclusion des responsabilités
Metrologic Instruments, Inc. et le/les auteur(s) ne sont ni garants, ni responsables pour l-
'exhaustivité et la correction des informations contenues dans cette brochure - que ce soit r-
elativement à leur teneur et à l' exactitude - ou pour le produit qui y est décrit. Ils ne sont en outre
responsables d'aucune garantie de propriété ou de qualité pour un usage particulier. Toutes les
assurances nommées ou exprimées excluent toute garantie ou responsabilité pour les dommages
spéciaux, indirects ou des suites de l'utilisation de cette brochure ou du produit qui y est décrit
respectivement. en rapport avec l'emploi de cette brochure et du produit qui y est décrit. Il leur est
également réservé le droit de procéder à des modifications de cette brochure sans avoir à en avertir
qui que ce soit. Metrologic se réserve en outre le droit de procéder à des modifications du produit
qui y est décrit.
Haftungsausschluß
Metrologic Instruments, Inc. und der/die Autor(en) übernehmen keinerlei Gewähr und haften nicht
für die Richtigkeit im Hinblick auf Inhalt oder Genauigkeit der Angaben dieser Veröffentlichung
oder des hierin beschriebenen Produkts. Sie übernehmen ebenso keinerlei Eignungsgarantie oder
Gewährleistung durchschnittlicher Qualität für einen bestimmten Zweck. Alle benannten oder
ausdrücklichen Zusicherungen schließen sämtliche Verpflichtungen oder Haftungen aus jeglichem
Schaden aus, ganz gleich ob speziell, indirekt oder als Folge der Verwendung dieser
Veröffentlichung oder des hierin beschriebenen Produkts bzw. in Zusammenhang mit der
Verwendung dieser Veröffentlichung oder des hierin beschriebenen Produkts. Darüber hinaus wird
das Recht vorbehalten, Änderungen an dieser Veröffentlichung vorzunehmen ohne die
Verpflichtung, irgend jemanden über solche Änderungen zu unterrichten. Metrologic behält sich
ferner das Recht vor, Änderungen an dem hierin beschriebenen Produkt vorzunehmen.
Esclusione della responsabilità
La Metrologic Instruments, Inc. e l’autore/gli autori non assumono nessuna garanzia e non
rispondono della correttezza per quanto riguarda il contenuto o la precisione di quanto indicato nel
presente Manuale o del prodotto in esso descritto. Neppure essi assumono una garanzia per
l’idoneità o una garanzia della qualità media per un determinato scopo. Tutte le garanzie citate o
fatte espressamente escludono qualsiasi obbligo o responsabilità derivanti da qualsiasi danno,
indipendentemente dal fatto che questo obbligo/questa responsabilità risulti in particolare, i-
ndirettamente o come conseguenza dall’uso del presente Manuale o del prodotto in esso descritto
oppure se è legato/a all’uso del presente Manuale o del prodotto in esso descritto. Inoltre ci si
riserva il diritto di modificare il presente Manuale senza essere obbligati ad informare persona
alcuna circa dette modifiche. Metrologic si riserva il diritto di apportare modifiche al prodotto
descritto nel presente Manuale.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E
Notices
Notice
This equipment has been tested and found to comply with limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his own expense. Any unauthorized
changes or modifications to this equipment could void the users authority to operate this device.
Notice
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Industry and Canada.
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous laser light. Under no circumstances should the customer attempt to service the
laser scanner. Never attempt to look at the laser beam, even if the scanner appears to be
nonfunctional. Never open the scanner in an attempt to look into the device. Doing so could result
in hazardous laser light exposure. The use of optical instruments with the laser equipment will
increase eye hazard.
Remarque
Après contrôle de cet appareil, on a noté qu'il répondait aux valeurs limites de la classe A,
conformément à la partie 15 des directives de l'administration fédérale américaine pour les
télécommunications. Ces valeurs limites ont été prévues pour garantir une protection suffisante
contre les effets nocifs dus à l'emploi de l'appareil dans un magasin. L'appareil génère et utilise une
énergie haute fréquence et peut, s'il n'est pas installé et utilisé conformément aux instructions
mentionnées dans le guide d'utilisation, entraîner des perturbations dans la radiocommunications.
L'utilisation de cet appareil dans une zone d'habitation entraînera très vraisemblablement des
perturbations. Dans ce cas, l'utilisateur est tenu de remédier à ces perturbations à ses propres frais.
Toute modification ou remplacement non autorisé sur cet appareil peut entraîner l'invalidité de
l'autorisation d'utilisation de l'appareil.
Remarque
Cet appareil numérique ne va pas contre les valeurs limites pour émissions de bruits radios des
appareils numérique de la classe A, conformément aux directives relatives aux perturbations des
radiocommunications du ministère canadien pour l'industrie.
Attention
L'emploi de commandes, réglages ou procédés autres que ceux décrits ici peut entraîner de graves
irradiations. Le client ne doit en aucun cas essayer d'entretenir lui-même le scanner ou le laser. Ne
regardez jamais directement le rayon laser, même si vous croyez que le scanner est inactif.
N'ouvrez jamais le scanner pour regarder dans l'appareil. Ce faisant, vous vous exposez à une
rayonnement laser mortel. L'emploi d'appareils optiques avec cet équipement laser augmente le
risque d'endommagement de la vision.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E (continued)
Anmerkung
Nach Überprüfung dieses Geräts wurde festgestellt, daß es den Grenzwerten für Digitalgeräte der
Klasse A gemäß Teil 15 der Richtlinien der US-amerikanischen Bundesbehörde für das
Fernmeldewesen entspricht. Diese Grenzwerte wurden festgelegt, um einen angemessenen Schutz
gegen schädliche Auswirkungen bei Einsatz des Geräts in einer Ladenumgebung zu gewähren.
Das Gerät erzeugt und verwendet Hochfrequenzenergie und kann diese ausstrahlen, und kann,
falls es nicht gemäß den im Bedienerhandbuch enthaltenen Anweisungen installiert und verwendet
wird, zu einer Störung des Funkverkehrs führen. Der Betrieb dieses Geräts in einem Wohngebiet
führt höchstwahrscheinlich zu Störungen. In diesem Fall ist der Bediener verpflichtet, die Störung
auf eigene Kosten zu beseitigen. Durch jegliche unerlaubte Auswechselung oder Änderung an
diesem Gerät könnte die Genehmigung des Bedieners zur Verwendung dieses Geräts ungültig
werden.
Anmerkung
Dieses Digitalgerät verstößt nicht gegen die Grenzwerte für Funkrauschemissionen von
Digitalgeräten der Klasse A gemäß den Richtlinien für Funkstörungen des kanadischen
Ministeriums für Industrie.
Achtung
Die Verwendung anderer als der hier beschriebenen Steuerungen, Einstellungen oder Verfahren
kann eine lebensgefährliche Laserstrahlung hervorrufen. Der Kunde sollte unter keinen
Umständen versuchen, den Laser-Scanner selbst zu warten. Sehen Sie niemals in den Laserstrahl,
selbst wenn Sie glauben, daß der Scanner nicht aktiv ist. Öffnen Sie niemals den Scanner, um in
das Gerät hineinzusehen. Wenn Sie dies tun, können Sie sich einer lebensgefährlichen
Laserstrahlung aussetzen. Der Einsatz optischer Geräte mit dieser Laserausrüstung erhöht das
Risiko einer Sehschädigung.
N.B.
Dal controllo di questo apparecchio risulta che esso risponde ai valori limite per apparecchi
digitali della classe A conf. parte 15 delle direttive sulle telecomunicazioni dell’Autorità federale
statunitense. Questi valori limite sono stati fissati per garantire una protezione adeguata contro gli
effetti nocivi se questo apparecchio viene usato all’intero di un negozio. L’apparecchio genera,
utilizza e può emettere energia ad alta frequenza e, se non viene installato ed utilizzato
conformemente alle indicazioni fornite nel Manuale utente, può provocare disturbi al servizio
radiofonico. L’uso di questo apparecchio in zone residenziali causa molto probabilmente dei
disturbi. In questo caso l’utente è obbligato ad eliminare questi disturbi a sue spese. Qualsiasi
sostituzione o modifica non autorizzata all’apparecchio potrebbe rendere invalida l’autorizzazione
dell’utente all’uso dell’apparecchio.
N.B.
Questo apparecchio digitale non supera I valori limite per l’emissione di radiorumori da parte di
apparecchi digitali della classe A conformemente alle direttive per radiodisturbi del Ministero
canadese per l’Industria.
Attenzione
L’utilizzo di sistemi di controllo, di regolazioni o di procedimenti diversi da quelli descritti nel
presente Manuale può provocare dei raggi laser pericolosi per la vita. Il cliente non deve
assolutamente tentare di riparare egli stesso lo scanner laser. Non guardate mai nel raggio laser,
anche se credete che lo scanner non sia attivo. Non aprite mai lo scanner per guardare dentro
l’apparecchio. Se tuttavia lo fate, potete esporVi a dei raggi laser pericolosi per la vita. L’uso di
apparecchi ottici con questo equipaggiamento laser aumenta il rischio di danni alla vista.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
Accessories
AC input/outlet 2, 4, 5, 7
Adapter
cable
Approvals
Assignments
pin
Audible indicators
Authorized service center 39
Autodiscriminates
2
Disclaimer
40
30
E
Electrical
External power supply
7, 36, 37
2, 7, 38
12
4, 5,
36-38
F
9
Failure indicator(s)
Failure modes
Female connector 2, 7,
38
Function(s)
9, 10,
9, 10
29
B
28, 31-38
Bar code
3, 8, 9, 11, 13,
16, 21, 23-25, 27, 29
Bar width 29
Beep(s) 3-6, 9-11, 22-24, 29
Beeper operation 29
Built-in PC keyboard wedge
interface 7, 28, 38
G
Green LED
3-6, 8, 9, 11,
22
Ground 36-38
H
Host
2-8, 11, 22, 23, 26
C
Cable
I
adapter 2, 7, 38
pin assignments 36-38
Indicators
Audible
Visual
9-10
11
PowerLink
2, 4-8,
36-38
LED 3-6, 8, 9, 11, 22, 23
Y-type 7, 37
Caution 41
CDRH 31
Characteristics 8-12
Input voltage
Installation
Interfaces
30
5-7
1, 6, 22, 28, 29,
36
Compliance
Configuration procedures 5-7
Connector(s) 39
5, 7
K
Keyboard Type(s)
Keyboard Wedge (KBW) 1, 2,
4, 7, 25, 28, 29, 36-38
29
Current 4, 7, 23, 31, 37, 38
Customer service 39
D
L
DC transformer 30
Decode capability 29
Default Settings 31-35
Labels 12
LEDs 3-6, 8, 9, 11, 22, 23
Light levels
30
Depth of field
13-20
Design specifications
29, 30
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Index(continued)
R
Razzberry tone 9-11
RDATA 36
Recommendation 7
Red led 3-6, 8, 9, 11, 23
Repair 10, 39
Rights
Light Pen
1, 2, 4, 6, 28,
36
29
Light source
List
2
M
property
warranty
39
39
Maintenance
Manufacturer’s recommendation
7
Mechanical
Min bar width
21
RMA 39
Roll, pitch, yaw 29
RS-232 1-6, 26-29, 36, 37
29
29
S
N
Scan lines
Scan pattern(s) 8, 13-20, 29
Scan speed 29
29
Normal depth of field
Notices 41, 42
14, 19
Scanner installation
SELV 5, 7
Service 39
5-7
O
OCIA 1, 2, 4, 6, 28, 29, 36
Operating current 30
Operating temperature
Operation
Operational
Operational test
Shock 30
30
1, 7, 9, 29
Specifications
29, 30
Storage temperature
System interfaces 29
30
29
4
Output 8, 21, 26, 36, 37
Output window 8, 21
T
Termination
Test
Transformers
Troubleshooting 22-26
Tones 1, 9, 10, 29
36-38
30
4
P
Parts
PC
8
1, 4-7, 25, 27, 28, 29,
36-38
Pin assignments 35-37
Port 5-8, 23, 26, 27, 38
Powered by 5, 6
PowerLink cable 2, 4-8, 36-38
V
Ventilation
30
Version 28, 36, 37
Visual indicators 11
Voltage 4, 5, 7, 30
Power supply
4, 5, 7, 22, 36,
37
Programming guide
2, 3,
9, 26, 28
W
Warranty
Weight 29
Window 8, 21
39
Protocols
28
Q
Quick start
3
44
Download from Www.Somanuals.com. All Manuals Search And Download.
|