INSTALLATION INSTRUCTIONS FOR PART 95-8224
APPLICATIONS
Toyota Matrix 2009-10
Pontiac Vibe 2009-10
(Excluding Factory Navigation Models)
95-8224
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
• A) Double Din Trim Plate • B) Double DIN Brackets
B
A
Harness & Antenna Connections (sold separately)
• 70-1761 - Toyota Harness 87-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Socket Set
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
95-8224 DASH DISASSEMBLY
Toyota Matrix/Pontiac Vibe 2009-10
A
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
PASSENGER
SECURITY
2
3
Unclip and remove the radio trim
panel including the a/c vent. (Figure A)
Remove (4) 10 MM bolts securing the
radio. Unplug and remove the radio.
(Figure B)
Continue to kit preparation.
2
A/C
B
1
Download from Www.Somanuals.com. All Manuals Search And Download.
95-8224 KIT PREPARATION
DOUBLE DIN RADIO PROVISION
STACKED ISO MOUNT UNITS
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
Snap the Double DIN Trim plate into
the rear of the factory radio trim
panel. (Figure A)
Continue to kit assembly.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
95-8224 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
STACKED ISO MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Attach the Double DIN brackets to the
Double DIN or the stacked ISO mount
unit(s) using the screws supplied with
the unit(s). (Figure A)
1
Continue to final assembly.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
95-8224 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
95-8224
NOTES
5
Download from Www.Somanuals.com. All Manuals Search And Download.
95-8224 INSTRUCTIONS
1-800-221-0932
REV. 04/27/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST95-8224
Download from Www.Somanuals.com. All Manuals Search And Download.
|