USER MANUAL
4 Stroke Petrol Edger
SAFETY OPERATION MAINTENANCE
Your edger has been engineered and manufactured to our high standard for dependability,
ease of operation, and operator safety.
WARNING: To reduce the risk of injury, the user must read and understand the
operator’s manual before using this product.
Thank you for your purchase.
SAVETHIS MANUAL FOR FUTURE REFERENCE
Model No. ME240
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
n General Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
n Specific Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
n Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
n Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
n Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
n Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
n Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-16
n Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
INTROdUCTION
This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and
dependability have been given top priority in the design of this product making it easy to maintain and
operate.
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
This manual is written for a person with some
WarninG
mechanical ability. Like most service books, not all
the steps are described. Steps on how to loosen
or tighten fasteners are steps anyone can follow
with some mechanical ability. Read and follow these
instructions before you use the unit.
Look for this symbol to point out important
safety precautions. It means:“ Attention!
Become Alert!Your Safety Is Involved.”
WarninG
Know your product: If you understand the unit
and how the unit operates, you will get the best
performance.As you read this manual, compare
the illustrations to the unit. Learn the location and
the functions of the controls.To help prevent an
accident, follow the operating instructions and the
safety rules. Keep this manual for future reference.
Engine Exhaust, some of its constituents, and
certain vehicle components contain or emit
chemicals known to cause cancer and birth
defects or other reproductive harm.
WarninG
To prevent accidental starting when setting up,
transporting, adjusting or making repairs, always
disconnect spark plug wire and put wire where
it cannot contact the spark plug.
IMPORTANT: Many units are not assembled and
are sold in cartons. It is the responsibility of the
operator to make sure the assembly instructions in
this manual are exactly followed.
Other units are purchased in an assembled
condition. On assembled units, it is the responsibility
of the operator to make sure the unit is correctly
assembled.The operator must carefully check the
unit according to the instructions in this manual
before it is first used.
with the controls and the proper use of the edger
before starting. Know how to stop the edger and
disengage the controls quickly.
• Familiarise yourself with all the safety and
operating decals on this equipment.
•Thoroughly inspect the area where the edger is
to be used and remove all foreign objects.Your
equipment can propel small objects at high speed
causing personal injury or property damage.
Stay away from breakable objects, such as house
windows, auto glass, greenhouses, etc.
RESPONSIBILITY OF THE OPERATOR
The responsibility of the operator is to follow the
instructions below:
1. Carefully read and follow the rules for safe
operation.
2. Follow all the assembly and preparation
instructions.
• Check that all nuts and bolts are tight and
equipment is in good condition.
3. Regularly inspect the edger. Make sure parts are
not bent, damaged, or loose.
OPERATION SAFETY
4. Use this equipment for its intended purpose only.
5. Make sure that the operator of the unit knows
how to correctly use all standard and accessory
equipment.
• Never allow children or young teenagers to
operate the edger.
• Keep area of operation clear of all bystanders,
particularly small children and pets.
6. Operate the unit only with guards, shields, and
other safety items in place and working correctly.
7. Correctly adjust the unit.
8. Service the unit only with authorised or approved
replacement parts.
9. Complete all maintenance on the unit.
SAFE OPERATION PRACTICES BEFORE USE
• Read, understand, and follow all instructions on the
machine and in the manuals. Be thoroughly familiar
• Only allow responsible individuals, who are familiar
with the instructions, to operate the edger.
• Do not operate the edger while under the
influence of alcohol, drugs, or other medication
which can cause drowsiness or affect your ability
to operate this machine safely.
• Do not use this machine if you are mentally or
physically unable to operate the machine safely.
• Always wear ANSI/SAA compliant safety goggles
Download from Www.Somanuals.com. All Manuals Search And Download.
1
GENERAL SAFETY RULES
or safety glasses with side shields when operating
edger to protect your eyes from foreign objects,
which can be thrown from the unit.
on the handle and walk; never run. Never operate
the edger at high transport speeds on slippery
surfaces.
•Wear appropriate clothing such as a long sleeved
shirt or jacket.Also wear long trousers or slacks.
Do NOT wear shorts. Do NOT wear loose
clothing, which could get caught in this equipment.
• Always wear work gloves and sturdy footwear such
as leather work shoes or short boots.These will
protect ankles and shins from small sticks, splinters,
and other flying debris, and improve traction.
• It is advisable to wear protective headgear
to protect against being struck by small flying
particles, or being struck by low hanging branches,
• Look behind and use care when backing.
• Never operate the edger without good visibility
or light.
• Do not run the engine indoors or inside a closed
area.The exhaust fumes are dangerous, containing
CARBON MONOXIDE, an ODORLESS AND
DEADLY GAS.
• Never leave the edger unattended when the
engine is running. Stop the engine and make sure
all moving parts have stopped. Remove the wire
from the spark plug.
twigs, or other objects, which may be unnoticed by • Do not overload the edger capacity by attempting
the operator.
to till too deep at too fast a rate.
• Do not put hands or feet near or under rotating
parts.
• Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert for
hidden hazards or traffic.
• If the edger should start to vibrate abnormally,
stop the engine, disconnect the spark plug wire
and prevent it from touching the spark plug. Check
immediately for the cause.Vibration is generally a
warning of trouble.
• Exercise caution to avoid slipping or falling.
Always besure of your footing; keep a firm hold
•Watch for holes, ruts, bumps, or other rough
ground.Tall grass can hide obstacles.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
SPECIFIC SAFETY RULES
FUEL SAFETY
• Handle fuel with care; it is highly flammable.
• Use an approved container.
• Check fuel supply before each use, allowing space
for expansion as the heat of the engine and/or sun
can cause fuel to expand.
• Fill fuel tank outdoors with extreme care. Never
fill fuel tank indoors.
•When servicing or repairing the edger, do not
tip the machine over or up unless specifically
instructed to do so in this Manual. Service and
repair procedures can be done with the edger in
an upright position. Some procedures will be easier
if the machine is lifted on a raised platform or
working surface.
• Use only original equipment or authorised
replacement parts.
• Never tamper with safety devices. Check their
proper operation regularly.
• Never remove petrol cap or add fuel with the
engine running.Allow engine to cool before
refueling.
• Do not smoke while refueling.
• After refueling, replace fuel tank cap securely and
wipe up spilled fuel.
• Never store fuel or edger with fuel in the tank inside
a building where fumes may reach an open flame.
• Do not change the engine governor setting or
over-speed engine.
• Clean and replace safety and instruction decals as
necessary.
•To guard against engine over-heating, always have
engine air filter mounted and clean.
STORAGE SAFETY
• Always refer to the operator’s manual instructions
for important details if the edger is to be stored
for an extended period.
• Never store the edger with fuel in the fuel tank
inside a building where ignition sources are
present such as water heaters, space heaters,
clothes dryers, etc.
•To reduce fire hazard, keep edger free of grass,
leaves, or other debris build-up.
• Allow the engine to cool before storing in any
enclosure.
CHILdREN SAFETY
•Tragic accidents can occur if the operator is not
alert to the presence of children. Children are
often attracted to the edger and the edging activity.
• Keep children out of the edging area and under the
watchful care of a responsible adult.
• Never assume that children will remain where you
last saw them.
• Be alert and turn edger off if children enter the
area.
• Before and while moving backwards, look behind
and down for small children.
REPAIR, MAINTAINANCE, ANd AdJUSTMENT SAFETY
• After striking a foreign object, stop the engine.
Remove the spark plug lead from the spark plug
and keep the spark plug lead away from the plug
to prevent accidental starting.Thoroughly inspect
the edger for any damage. If damaged, have the
equipment repaired by a trained technician before
restarting and operating.
• Never allow children to operate the edger.
• Use extra care when operating near blind corners,
shrubs, trees, or other objects that may obstruct
vision.
• Stop the engine before cleaning, repairing, or
inspecting the unit. Make sure all moving parts have
stopped. Let the engine cool, disconnect the spark
plug lead and move it away from the spark plug.
• Never attempt to make any adjustments while
the engine is running except when specifically
recommended by the manufacturer.
• Keep the edger in safe working condition. Check
all fasteners at frequent intervals for proper
tightness.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
SYMBOLS
CONTROL ANd OPERATING SYMBOLS
IMPORTANT:
Many of the following symbols are located on your unit or on literature supplied with the product. Before
you operate the unit, learn and understand the purpose for each symbol.
ENGINE STOP
ENGINE STOP
OIL
FUEL
RUN
CHOKE
OIL FILL
SAFETY ALERT SYMBOLS
Indicates danger, warning, or caution.Attention is required in order to avoid serious personal injury.The
signal word (DANGER,WARNING, OR CAUTION) is used with the alert symbol to alert you to special
instruction about a particular operation that may be hazardous if performed incorrectly or carelessly.
Observe them carefully.
syMBol
dANGER
exPlanation
Failure to obey a safety warning will result in serious personal injuries or
deaths.
Failure to obey a safety warning can result in serious personal injuries or
deaths.
WARNING
CAUTION
Failure to obey a safety warning may result in minor or moderate injuries.
When used without the alert symbol, could result in damage to your engine
or other property.
CAUTION
Download from Www.Somanuals.com. All Manuals Search And Download.
4
SYMBOLS
SAFETY WARNING SYMBOLS
syMBol
DeFinition
IndicatesWARNING, DANGER, or CAUTION.
Read operator’s manual before operating this machine. Failure to follow directions
could result in serious injury.
Thrown objects. Do not use if children or bystanders are present. Remove all objects
which could be thrown by machine. Read operator’s manual before operating this
machine.
Rotating parts can cause serious injury. Keep away from rotating parts. Stop engine
and disconnect spark plug wire before making adjustments.
Wear eye protection complying with SAA ANSI Z87.1 and hearing protection.
Disconnect spark plug wire before servicing unit.
Engine emits carbon monoxide. Do not run indoors or in enclosed area.
Do not touch hot muffler or cylinder.These parts are extremely hot from
operation and may remain hot for a short time after operation.
To reduce risk of fire, clean spilled gas and oil and keep unit free from debris. Petrol
is extremely flammmable.Allow machine to cool before refueling.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
FEATURES
Engine Displacement. . . . . . . . . . . . . . . . . . . . . . 87cc
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . .[400 ml]
Spark Plug Model . . . . . . . . . . . . . . . . . . . . . . E7RTC
Spark Plug Gap . . . . . . .0.027-0.031 in. [0.7-0.8 mm]
Edger Blade Size . . . . . . . . . . . . . . . . . 9 in. [228 mm]
Petrol Capacity . . . . . . . . . . . . . . . . . . . . . . . . . .1.6 L
PetrolType . . . . . . . . . . . . . . . . . . Unleaded Regular
OilType (API SG-SL). . . . . . . . . . . . . . . . . . . . SAE 30
KNOW YOUR EDGER
READTHE OPERATOR’S MANUAL AND ALL SAFETY RULES BEFOREYOU OPERATE the edger. To
familiarise yourself with the location of the controls, compare Figure 1 with your edger. Save this manual for
future reference.
REAR VIEW
FRONT VIEW
Clutch Lever
Spark Plug/
Spark Plug Lead
Start Lever
Control Rod
Recoil Starter
Handle
Oil Fill Cap/
Dipstick
Angle Cut Lever
Choke Control
Blade Guard
Throttle Control
Adjustable Rear
Wheel
Adjustable FrontWheel
Figure 1
from side to side for balance.The front wheel can
also adjust down for curb-hopping.
Throttle Control Controls the engine speed.
Start Lever Lever on handle which allows the
engine to run.When lever is released, engine will
stop.
Recoil Starter Handle The engine is equipped
with an easy pull recoil starter.
Angle Cut Lever Permits adjusting the cutting
angle to 15 degrees, 0 degrees (vertical), or -15
degrees.To change the angle, pull the lever and
rotate the quill assembly to the desired angle.
Choke Control Restricts the air intake.This allows
for an enriched fuel-air mixture which helps to start
the engine.
Clutch Lever Use to start and stop the blade and
Blade Guard Use to prevent stones and debris
control the depth of cut.
from being thrown at the operator.
Adjustable RearWheel Right rear wheel is
adjustable to level the edger when edging along a
curb (curb-hopping).
Spark Plug/Spark Plug Lead Provides spark to
ignite air/ fuel mixture.The Spark Plug Lead must be
disconnected and moved away from the Spark Plug
when servicing the unit.
Adjustable Front Wheel Front wheel is adjustable
Download from Www.Somanuals.com. All Manuals Search And Download.
6
ASSEMBLY
Read and follow the assembly and adjustment
The following components will be found in the
carton with the quantities shown in ( ):
(1) Edger Operator’s Manual
(1) Upper Handle
instructions. All fasteners are in the parts bag. Do
not discard any parts or materials until the unit is
assembled.
(1) Lower Handle
(1) Handle Panel
WARNING
Before doing any assembly or maintenance to
the unit, remove the lead from the spark plug.
(1) Control Rod
(1) 400 ml container of engine oil
(1) Parts Bag containing the following:
(4) Pipe Bolts
NOTE:Torque is measured in foot-pounds (metric
unit is Nm).This measurement describes how tight a (4) M8X16 Bolts
nut or bolt must be.The torque is measured with a
torque wrench.
(8) M8 Nuts
(2) Cotter pins
(2) Cable ties
WARNING
Figure 2 shows the edger completely assembled.
Always wear ANSI/SAA compliant safety glasses
with side shields while assembling the edger.
References to the right or left side of the edger
are from the viewpoint of the operator’s position
behind the unit.
The following tools will be required for assembly of
the edger with the quantities shown in ( ):
(2) AdjustableWrenches
(1) Utility Knife to Cut Carton
(1) BladeType Screwdriver
(1) Pliers
(1) Oil Funnel
(1)TorqueWrench to Check FastenerTightness
Figure 2
Download from Www.Somanuals.com. All Manuals Search And Download.
7
ASSEMBLY
HOW TO ASSEMBLE THE HANDLE
1. Mount the lower handle to the inside of the edger
frame with the (4) M8X16 bolts, and (4) M8 Nuts
(See Figure 3).As you tighten the fasteners, pull back
on the handle.The torque for all nuts and bolts in the
handle should be 7.4-11.8 foot-pounds [10-16 Nm].
2.Assemble panel with nuts and bolts provided. Insure
that the nuts are to the inside.Assemble the top
folding handle with the 2 handle lock levers and
bolts provide.Tighten folding Handles in to position
by tightening locking handles by hand.
3.
Connect the wires using the plastic connectors fitted.
Secure wires with handle clips provided. (See Figure
Figure 4
4)
Cotter Pin
4. Use the (2) cable ties to secure the loose cable
coming from the start lever to the handle. Use (1)
cable tie on the right side of the upper handle and
(1) cable tie on the left side of the lower handle.
Make sure cable goes behind handle panel.
5. Slide one end of the control rod from left to right
through the hole in the clutch lever. Secure with the
cotter pin. (See Figure 5)
6. Move the clutch lever to the first depth position.
Attach the other end of the control rod to the quill
support arm with the cotter pin. (See Figure 5)
7. Move the clutch lever back to the “N” NEUTRAL
position.
NOTE: If it is difficult to move the clutch lever to the
“N” NEUTRAL position,loosen the fasteners that hold
the lower handle to the edger frame (See Figure 5).Raise
the handle until the clutch lever will easily move to the
“N” NEUTRAL position.Tighten the fasteners.
8.When the clutch lever is in the NEUTRAL position,
the quill support arm must be close to the screw.
(See Figure 6)
Neutral Position
Upper
Handle
Control
Rod
Locking
Handles
Quill
Support
Arm
M8 Nut
Cotter
Pin
Locking
Handles
Lower
Handle
Figure 5
Quill
Support
Arm
Edger Engine
M8x16
M8x16
Screw
M8 Nuts
M8x16
M8x16
Edger Frame
Figure 3
Figure 6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
ENGINE PREPARATION
ENGINE DOES NOT CONTAIN OIL OR PETROL WHEN SHIPPED
iMPortant: This unit is equipped with an internal
combustion engine and must not be used on or near
Before you use the unit, read the information on safety, any forest-covered, brush-covered or grass-covered
operation, maintenance, and storage.This edger was
shipped with a 400 ml contain er of SAE30 motor oil.
This oil is to be added to the engine before operating.
Follow the below procedure to fill the crankcase with
oil.
land unless the engine’s exhaust system is equipped
with a spark arrestor meeting applicable local or state
laws. If a spark arrestor is used, the operator must
maintain it in effective working order.
cHecKlist
FIRST TIME FILL
For the best performance and satisfaction from this
quality product, please review the following checklist
before you operate the edger:
• All assembly instructions have been completed.
• Check carton to make sure no parts are remaining.
• All fasteners have been properly tightened.
1. Place the edger on a level surface and make sure the
adjustable wheels are set so the main frame of the
edger is level.
2. Remove the oil fill cap/dipstick.
note: the crankcase is shipped empty. Fill with 400
ml of oil.
3.When adding oil, use a funnel or a nozzle for the oil
container to reduce spillage.
4. DO NOT OVERFILL. Check the oil level by
following the instructions below.
As you learn how to use the edger, pay extra attention
to the following important items:
• Engine oil is at proper level.
• Fuel tank is filled with a fresh, clean, regular unleaded
petrol.
TO CHECK THE OIL LEVEL ANd FILL TO PROPER LEVEL
1. Place the edger on a level surface and make sure the
curb-hoping wheels are set so the main frame of the
edger is level.
2. Remove the oil fill cap/dipstick and wipe clean with
cloth. (See Figure 7)
• Become familiar and understand the function of all
controls. Before you start the engine, operate all
controls.
FuelTank
Oil Fill Cap/
Dipstick
3. Replace dipstick and do NOT screw it. Remove and
check oil level.
4.When oil level is full, the oil will be at upper limit on
dip stick. (See Figure 8)
5. If the oil level is near or below the lower limit mark
on the dipstick (See Figure 8), add oil slowly and
recheck until oil level reaches upper limit of dipstick.
DO NOT OVERFILL.
6. Replace and tighten dipstick.
7. Clean up any spilled oil.
note: When adding oil, frequently insert the oil fill
cap/dipstick and check the amount of oil in the engine.
DO NOT OVERFILL.
Figure 7
Oil Fill Cap/
Dipstick
WarninG
Follow the user manual instructions for the type
of petrol and oil to use.Always use a safety petrol
container. Do not smoke when adding petrol to
the engine.When inside an enclosure, do not
fill with petrol. Before you add petrol, stop the
engine. Let the engine cool for several minutes.
Upper Limit
Lower Limit
Figure 8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
OPERATION
WarninG
Debris thrown from the edger can result in
Throttle Control
foreign objects being thrown into eyes, which
can cause severe eye damage.Always wear
ANSI/SAA compliant safety glasses or eye
shields when operating the edger. If you wear
eyeglasses, use aWideVision Safety Mask over
your eyeglasses.
Increasing
Speed
Decreasing
Speed
HOW TO USE THE THROTTLE CONTROL
1. During normal use, run the engine at full speed.
2. Move the throttle control rearward to increase
engine speed, or forward to decrease engine
speed. (See Figure 9)
IDLE
Figure 9
HOW TO USE THE CHOKE
Choke Lever
To start the the engine, slide the choke lever to the
CHOKE
running for 2-5 seconds, slide the choke lever to the
RUN position. (See Figure 10)
position.After the engine has been
RUN
HOW TO USE THE CLUTCH LEVER
1.To engage the cutting blade, move the clutch lever
forward. (See Figure 11)
Choke
2. Select the edging depth you need.There are five
selections down to approximately 70 mm deep.
FILLING TANK
1. Clean surface around fuel cap to prevent
contanimation.
2. Remove fuel cap slowly. Place the cap on a clean
surface.
3. Carefully pour fuel into the tank.Avoid spillage.
4. Prior to fitting the fuel cap, clean and inspect the
gasket.
Figure 10
Forward
Start
Lever
Clutch
Control
5. Immediately refit fuel cap and hand tighten.Wipe
up any spillage.
note: It is normal for smoke to be emitted from a
new engine after the first use.
Neutral
Full
Depth
Figure 11
Download from Www.Somanuals.com. All Manuals Search And Download.
10
OPERATION
HoWto starttHe enGine
DO NOT allow the starter rope to snap back. Let
the starter rope slowly rewind. If the engine does
not start in 5 or 6 tries, see the instruction in the
“Troubleshooting Chart”.
note:tHe start leVer Hasto Be
alWays HelD aGainsttHe HanDle
FortHe enGineto run.
note: DO NOT BE ALARMED; your engine will
smoke the first time it is started. It is burning off
the protective coating that is on the internal engine
parts.
note: Make sure engine is level before starting.
10.After the engine starts, wait 2-5 seconds and
slide the choke back to the RUN position.
11.When the engine is running, move the throttle
control lever forward (SLOW Position) to
decrease speed or backwards (FAST position)
to increase speed. During normal use keep the
throttle in the FAST position. (See Figure 9)
iMPortant: Before you start the engine, move
the edger to the desired location. Operate the
controls several times. Make sure all controls move
freely.
1. Check the oil.
2. Fill the fuel tank with regular unleaded petrol.
Make sure the petrol is clean. Leaded petrol will
increase deposits and shorten the life of the
valves.
HoWto stoPtHe eDGer
Release the start lever.This will ground the flameout
wires and stop the engine.
note: Do not use gasohol or methanol. Do not
use premium-unleaded petrol.
WarninG
Never run the engine indoors or in a poorly
ventilated area. Engine exhaust contains
carbon monoxide, an odorless and deadly gas.
Keep hands, feet, hair, and loose clothing away
from any moving parts.Avoid the muffler and
surrounding areas.Temperatures can exceed
150 degrees.
WarninG
Always use a safety petrol container. Do not
smoke when adding petrol to the fuel tank.
When inside an enclosure, do not add petrol.
Before you add petrol, stop the engine and let
the engine cool for several minutes.
3. Make sure the spark plug lead is connected to the
spark plug.
4. Pull the clutch lever all the way back to raise and
disengage the blade
5. Move the throttle control lever all the way to full
throttle.
6. Slide the choke to the CHOKE position. (See
Figure 10)
7. Hold the recoil starter handle firmly with your
right hand.
8. Hold the edger handle firmly with your left hand,
pulling the start lever against the handle.
tHe enGineWill not start iFtHe
start leVer is not PulleD aGainst
tHe HanDle (FiGure 11).
9. Pull the recoil slowly, until you feel tension in the
starter rope.Then quickly pull the recoil starter
handle to completely unwind the starter rope.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
OPERATION
HoWto usetHe anGle cut leVer
For a BeVeleD eDGe
The index lever has positions that will provide a
beveled edge (15, 0, -15 degrees).A bevel edge cut
along a sidewalk or driveway makes a trench and will
reduce the need to edge as often.
1. Stop the engine and disconnect the spark plug
wire from the spark plug.
2. Loosen the front wheel knob (See Figure 12). Slide
the front wheel all the way to the right side.This
will prevent the blade from hitting the wheel.
3. Securely tighten the front wheel knob.
4. Disengage the angle cut lever (See Figure 13).
Move the angle cut lever to the desired notch
(15, 0 or -15 degrees).
FrontWheel Knob
FrontWheel
Figure 12
5. Before you start the engine, line up the edger as if
you were going to bevel cut. Move the clutch lever
down to test the blade location. Return the clutch
lever to the “N” NEUTRAL position.
6. Reconnect the spark plug wire to the spark plug.
7. Start the engine.
8. Move the clutch lever to the desired cutting
depth.
Angle Cut Lever
Figure 13
Download from Www.Somanuals.com. All Manuals Search And Download.
12
OPERATION
HoWto usetHe curB-HoPPinG
Feature
eDGinGtiPs
Because the front wheel and the right rear wheel
are adjustable, the edger can be used on uneven
surfaces, such as a curb shown in Figure 14. Set the
wheel position as follows:
1. Stop the engine.
2. Disconnect the spark plug wire from the spark
plug.
3. Loosen the front wheel knob.
4. Slide the front wheel to the best position to clear
the curb and balance the unit.
WarninG
Read the Operator’s manual. Know location
and functions of all controls. Keep all safety
devices and shields in place. Never allow
children or uninstructed adults to operate the
edger. Shut off engine before unclogging blade
or making repairs. Keep bystanders away from
machine. Keep away from the blade and all
rotating parts, which cause injury.
5. Securely tighten the front wheel knob.
6. Use the curb height adjustment lever to lower the
front wheel. Lower the front wheel until the front
wheel is level with the left rear wheel and the unit
is sitting on the curb. (See Figure 14)
7. Loosen the rear wheel knob.
8. Lower the right rear wheel until the edger is level
and the left rear wheel is on the curb.
9. Securely tighten the rear wheel knob.
10. Connect the spark plug wire to the spark plug.
• Edging is best performed when conditions are
dry. If the soil is too wet, dirt becomes packed
around the blade causing premature belt wear and
decreased performance.
• If dirt does become packed around the blade, stop
the engine and remove the wire from the spark plug.
Remove the front guard cover, clean around the
blade and then refit the guard cover.
• For deep edging,first cut at shallow depths.Then,cut
at greater depths until the desired depth is obtained.
• For uniform edging, make sure the blade guide
rides on the surface.
• Edging can be customised by varying the number
of passes and by the distance the blade is from the
FrontWheel Knob
Blade Guard
Spark PlugWire
Support Rod
RearWheel Knob
Right RearWheel
FrontWheel
FrontWheel Adjustment Lever
Figure 14
Download from Www.Somanuals.com. All Manuals Search And Download.
13
MAINTENANCE
PERIODIC MAINTENANCE SCHEDULETABLE
Service Records Fill in dates
as you complete regular
service
After
First 2
Hours
Before
Each Use
Every 10 Every 25
Before
Each
Season
Before
Storage
Hours
Hours
Lubriate All Pivot Points
LubricatesWheel Axles
Check Engine Oil
Check Spark Plug
Check Drive Belt
Check Fasteners forTightness
Check Blade forWear or
Damage
GENERAL RECOMMENDATIONS
The warranty on this edger does not cover items that have been subjected to operator abuse or negligence.
To receive full value from the warranty, the operator must maintain the edger as instructed in this manual.
Some adjustments must be made periodically to properly maintain your edger.
All adjustments in the Maintenance section of this manual must be checked at least once each season.
STORAGE AND TRANSPORTATION
FOLDING HANDLE
1. Remove retaining pin from control rod (upper) (Fig A)
2. Loosen lock knobs (Fig B)
3. Fold handle down (Fig C) make sure control rod is clear of other parts
Figure A
Figure B
Figure C
Download from Www.Somanuals.com. All Manuals Search And Download.
14
MAINTENANCE
enGine Maintenance
Use the following maintenance section to keep your
unit in good operating condition. Before you start the
engine, read this book.
luBrication
1.After each 10 hours, apply a small amount of engine
oil to all pivot points
2.After each 25 hours, apply a small amount of engine
oil to the wheels.
HoWto cHanGetHe oil
1. Shut off engine and wait for it to cool.
Drain Plug andWasher
2. Disconnect spark plug wire from the spark plug.
3. Remove the drain plug and washer. (See Figure 15)
4.Tilt edger to drain all the engine oil into a flat pan.
5. Fill the engine crankcase. DO NOT OVERFILL. Refer
to Engine Preparation section for instructions on
filling oil to proper level.
Figure 15
Spacer
6. Connect the spark plug wire to the spark plug.
Engine Pulley
HoWto reMoVetHe Belt
The belt is made of a special compound. If the belt
becomes worn or breaks, replace the belt with an
original equipment belt.The belt length is 32.6 in.
[828.04 mm] and the section is 4L.
Rear Belt
Guide
Screw
1. Disconnect the spark plug wire from the spark plug.
2. Pull the clutch lever back to the “N” Neutral
position to release tension from the belt.
3. Remove the two screws and spacers from the top
of the engine pulley cover. Remove the engine pulley
cover. (See Figure 16)
4.Loosen,do not remove,the screw that holds the rear
belt guide.Then,move the belt guide away from the belt.
5.Remove the screws from the belt guard. Undo pulley
nut,remove pulley washer.(See Figure 17)
Engine
Pulley
Cover
Rear
Guard
Screws
Figure 16
6.Remove the old belt from the engine and quill assembly
pulleys.Replace with an original equipment belt.
7.To install a new belt, reverse the above steps.
•The rear guard fasteners should be tightened to 7.4-
11.8 foot-pounds [10-16Nm].
Front Guard
Screws
•The front guard fasteners should be tightened to 7.4-
11.8 foot-pounds [10-16Nm].
•The rear belt guide fasteners should be tightened to
34-45 foot-pounds [47-61Nm].
Pulley Nut
•The front belt guide fasteners should be tightened to
7.4-11.8 foot-pounds [10-16Nm].
Front Guard
Screws
Belt Guard
Figure 17
Download from Www.Somanuals.com. All Manuals Search And Download.
15
MAINTENANCE
HoWto rePlacetHe BlaDe
The blade is subject to wear and damage, such as nicks
To replace the blade, follow the steps below.
(Figure 18A & 18B)
and dents.This will not generally affect its function.
1. Disconnect the spark plug wire from the spark plug.
2. Remove blade cover by undoing the 3 wingnuts
(Fig 18A).
3. Remove blade locknut that holds the blade to the
drive shaft. (Fig 18B)
The blade is designed to not require sharpening. Do
not attempt to sharpen the blade.The blade is also
reversible. If nicks or dents are excessive, remove
the blade and turn it around.This will provide a fresh
cutting edge. Replace the blade if both sides are worn
or damaged.
WarninG
To remove or tighten the blade locknut, always use
the method shown in Figure 18B.Always position
the holding wrench on the nut behind the blade.
WarninG
4. Remove the blade.
Do not sharpen the blade. Sharpening can
damage the blade and cause it to break, which
can cause injury to you or to others.
5. Install a new blade and blade locknut.Tighten the
blade locknut to a torque of 40-45 foot-pounds
[54-61 Nm].
6. Refit blade cover.
Wing Nuts
Blade Lock Nut
Figure 18B
Figure 18A
1. Let the engine run until it is out of petrol.
2. Remove the spark plug from the cylinder. Pour few
drops of oil into the cylinder. Slowly pull the recoil-
start grip so that the oil will protect the cylinder.
Install a new spark plug in the cylinder. Pull starter
handle slowly a few times to distribute oil.
3. Clean the dirt and debris from the cylinder cooling
fins and the engine housing.
storaGe
WarninG
Never store the edger indoors with fuel in the
fuel tank. Never store in an enclosed, poorly
ventilated area where fumes could reach an open
flame, a spark or a pilot light as on a furnace,
water heater or clothes dryer.Allow engine to
cool before storing unit.
4. Completely clean the edger. Remove all dirt,
grease,leaves, etc.
5. Check the edger for worn or damaged parts. Have
damaged parts replaced if necessary.
6.Tighten all loose hardware.
7.Apply lubrication as directed in Maintenance section.
8. Put the unit in a building that has good ventilation.
9.When engine completely cold, Cover the edger
with a suitable protective cover that does not retain
moisture. Do not use plastic. Plastic cannot breathe
which allows condensation to form and will cause
your unit to rust.
WarninG
Do not remove petrol while inside a building,
near a fire, or while you smoke. Petrol fumes can
cause an explosion or a fire.
NOTE:A yearly checkup or tune-up at an authorised
service centre will make sure that the edger will
provide maximum performance for the next season.
When the edger is put in storage for thirty days or
more, the following steps should be followed to make
sure the edger is in good condition the next season.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
TROUBLESHOOTING
Problem
Possible cause
solution
Engine difficult to start
Stale fuel
Drain fuel tank. Fill with fresh fuel.
Clogged fuel filter
Replace fuel filter.
Engine runs erratically
Dirt in fuel tank or out of fuel
Fouled spark plug
Clean fuel tank.
Clean and set spark plug gap.
Clean or replace air filter.
Engine will not run at full
speed
Dirty air filter
Choke is in the CHOKE position Slide choke to RUN position.
Clogged air filter Clean or replace air filter.
Choke is in the CHOKE position Slide choke to RUN position.
Engine smokes
excessively
Cutting blade will not rotate
Debris interfering with blade
Loose blade
Clean debris from blade.
Tighten blade nut.
ReplaceV-belt.
DefectiveV-belt
Blade will not cut properly
Excessive vibration
Damage or worn blade
Loose parts
Reverse or replace the blade.
Stop engine immediately.
Tighten all fasteners. If vibration
continues, take the unit to an
Authorised Service Centre.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
|