LS7500CD 08/03/00 2:49 PM Page 1
OWNER'S MANUAL
LS7500CD
AM/FM Stereo Receiver and Compact Disc Player
Designed for In-Wall Installation of All Recreational Vehicles, Motor Homes and Mobile Housings
12 Volts DC
®
A Registered Trademark of Magnadyne Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 3
CONTROLS AND FUNCTIONS
1. On/Off Button
9. Skip Up Button
Press this button in to turn the unit on. Press again to turn the
unit off.
To skip to the next higher track on the compact disc, press
this button.
2. AM/FM/CD Function Knob
After turning the unit on, select the desired playing mode with
this knob.
10. Program Button
Use the program button to arrange the tracks on the disc to
play in the order you wish. (See compact disc operation)
3. FM Stereo Indicator Light
11. Dial Indicator
When the tuner is receiving a strong stereo FM signal, the
stereo light will be lit.
The dial indicator will move up and down the scale as you
rotate the tuning knob (4) indicating the station you are
listening to.
4. Radio Station Tuning Knob
12. 3-Band Graphic Equalizer
Rotate this knob to locate the radio station that you desire.
Rotating it clockwise will take you up the frequency band and
rotating it counter-clockwise will take you down the frequency
band.
These controls will tailor the overall tone of the unit. Slide
these controls up and down to achieve a tone that will suit
your taste.
13. Balance Control Knob
5. Compact Disc Door Button
Sliding this knob from left to right will allow you to balance
the sound to suit your taste.
By pressing the compact disc door button the door will open
to allow you to insert a compact disc.
14. Volume Control Knob
6. Play/Pause Button
Rotate this knob to increase the volume of the unit.
After inserting a compact disc press this button to begin
compact disc play. Pressing this button again will stop the
compact disc until the button is pressed again.
15. Speaker A/B Selector Buttons
To play the "A" set of speakers, press the "Speaker A"
button. To play the "B" set of speakers, press the "Speaker
B" button. To play the "A" and "B" speakers at the same
time, press both buttons in.
7. Stop Button
When this button is pressed, compact disc play will stop.
8. Skip Down Button
16. Headphone Output
To skip to the next lower track on the compact disc, press
this button.
The headphone jack accepts a standard walkman type
headphone plug (3.5mm). When the headphones are
plugged into the headphone jack, all external speakers are
turned off.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 4
CONTROLS AND FUNCTIONS
17. Random Button
Compact Disc Operation
Use the random button to play the disc tracks in an random
order selected by the disc player computer.
1. Press the on/off button (1) in to turn the unit on.
2. Use the function knob (2) to select CD operation.
3. Press the open button (5) and gently pull the compact disc
door open fully.
18. Intro Button
Use the intro button to listen to the first 10 seconds of all the
tracks on the compact disc.
4 Insert a disc onto the disc hub and press gently in the
center until the disc is secure and supported by the hub.
5. Close the compact disc door until it snaps into place.
6. Press the skip up/down buttons (8 / 9) to select a specific track.
7. Press the play button (6) and adjust the volume, balance
and 3 band graphic equalizer controls as desired.
19. Repeat Button
Use the repeat button to continuously play one song repeatedly
or to continuously play the entire disc repeatedly.
20. Compact Display
This display contains all the information about the disc that
is playing and all the modes the disc can play under.
(See compact disc operation)
Warning ! Never touch the laser eye. Moisture and oils
from your fingers can impair proper operation.
Radio Operation
1. Press the on/off button (1) in to turn the unit on.
2. Use the function knob (2) to select the AM orFM radio band.
3. Tune in the desired radio station by rotating the tuning knob (4).
4. Adjust the volume, balance and 3-band graphic equalizer
controls as desired.
TUNING
PGM
REP1
INTRO
AM 540 600 700 800 1000 1200 1400 1600 KHZ
TRACK
RANDOM INTRO REPEAT
FM 88 92
96
100
104
108
MHZ
STEREO
PLAY/
PAUSE
SKIP
DOWN
SKIP
UP
STOP
PROG
PHONES
POWER
A
B
SPEAKER SELECTION
VOLUME
FM Stereo Operation
MIN
The unit will automatically switch from FM mono to FM stereo
when the signal strength increases to a stereo level. If the signal
should become weak on stereo reception, the unit will switch
back to the mono mode.
L
-12
R
BALANCE
Note: Stereo operation is indicated by the stereo light (3) on the
front of the unit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 5
CONTROLS AND FUNCTIONS
Using the Program Feature:
Using the Random Feature:
The random feature allows the disc player to select the disc
tracks in an uncontrolled random play order. To initiate the
random play feature, press the random button (17) before
pressing the play button (6). When the play button is pressed,
a moving random indicator will appear in the display area while
the computer is searching for a track selection. When a song
has finished playing, the moving random indicator will appear
in the display again until the selection is made.
If you desire to have the song selection of the disc played in a
different order than arranged on the disc, repeat the following
procedures to program the playing order.
1. Press the program button (10). PGM
00 will appear in the display.
☛
2.Use the skip up/down buttons (8/9)
to select the first song to play. Press
the program button to lock the
selection.
Moving Random Indicator
3.Repeat step #2 as many times as
needed to determine the playing
order. You can program up to 21
selections.
☛
4.After programming is completed,
press the play button (6) to initiate
the program.
Using the Intro Feature:
The intro feature allows the disc player to play the beginning of
each track for 10 seconds and then move on to the next track.
This allows the unit to preview each song quickly or to find a
selection where the title may be unknown but the melody is
familiar.
1. Press the intro button (18) INTRO will
appear in the display
Note 1: After the program sequence has completed, pressing
the play button will start the play program again.
☛
Note 2: Pressing the stop button (7) will stop the program. To
re-start the program, press the program button (10) and then
press the play button (6).
2. Press the play button (6) to start
playing the first song.
Note: When you find the song you want
to listen to, press the intro button once
again to turn off the intro feature (intro is
off when INTRO is not being displayed.
Note 3: Opening the compact disc door by pressing the open
button (5) this will clear the play selection programming.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 6
CONTROLS AND FUNCTIONS
Using the Repeat Feature:
Handling the Disc:
The repeat feature has two modes of operation. A single track can
be continuously repeated or the entire disc can be continuously
repeated.
1. When inserting the disc, hold the disc with your thumb,
middle finger and index finger and press the center with
your index finger.
2. When removing the disc, always pull at the left or right edge
of the disc until it snaps loose from the disc hub. There are
indentations in the plastic for your fingers at these points.
1. Press the repeat button one time while a track is playing.
REP1 will show in the display area. The track that is playing
will continuously repeat.
2x
2. Press the repeat button two times while a track is playing.
REP will be displayed. When the last track on the disc has
finished playing, play will start over at track #1.
3. Always keep your disc’s clean and free from cracks,
fingerprints and dirt.
3x
3. To turn off the repeat feature, press the repeat button (19) a
third time (the REP indicator will be off in the display).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 7
INSTALLATION
Wall Panel
End Caps
Structural
Stud
Caution: Do not install radio without rear
cover installed. No user-serviceable parts
inside. Rear cover provides protection
against potential fire hazard.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 8
POWER CONNECTIONS
This unit for use only with a 12 volt DC power
source with a negative ground.
RED Wire (+)
To 12 Volt DC Power
BLACK Wire (-) Ground
8
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 9
SPEAKER CONNECTIONS
Left Speaker (A)
+
Right Speaker (A)
+
_
_
BROWN Wire
GRAY Wire
WHITE Wire
ORANGE Wire
_
_
GREEN Wire
BLUE Wire
+
+
Left Speaker (B)
Right Speaker (B)
Speaker Connections: Do not confuse the A and B speaker sets
9
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 10
ANTENNA CONNECTIONS
External Automotive
Type Antenna Socket
Either
or
External Automotive
Type Antenna (Not Provided)
DP36AXT In-Wall Antenna (Not Provided)
If an automotive antenna is not available or is undesired, we
recommend the use of a Magnadyne DP36AXT di-pole
antenna substitute. Plug the male plug from the DP36AXT
into the female receptacle of the LS7500CD unit and allow
the cable of the antenna to lay inside the wall.
The LS7500CD have a provision for a standard automotive
antenna. If an automotive antenna is used, plug the male
plug from the antenna into the female receptacle provided
on the unit.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 11
SAFETY INSTRUCTIONS
Read Instructions: All the safety and operating instructions
should be read before the appliance is operated.
Outdoor Antenna Grounding: If an outside antenna is
connected to the receiver, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built up static charges. Section 810 of the National
Electrical Code, ANSI/NFPS no. 70-1983, provides information
with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See figure 1.
Retain Instructions: The safety and operating instructions
should be retained for future reference.
Heed Warnings: All warnings on the appliance and in the
operating instructions should be adhered to.
Follow Instructions: All operating and use instructions should
be followed.
Object and Liquid Entry: Care should be taken so that objects
do not fall and liquids are not spilled into the enclosure through
openings.
Water and Moisture: The appliance should not be used near
water-- for example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool, etc.
Wall or Ceiling Mounting: The appliance should be mounted
to a wall or ceiling only recommended by the manufacturer.
Example of Antenna Grounding as per
National Electrical Code. Instructions
Contained in Artical 810-"Radio and
Television Equipment"
Heat: The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
Antenna Lead-In Wire (B)
Mast
Antenna Discharge
Unit (C)
Power Supply: The appliance should be connected to a power
supply only of the type described in the operating instructions
or as marked on the appliance.
Ground
Clamp
To Receiver
Ground
Wire
(A,B)
Cleaning: The appliance should be cleaned only as
recommended by the manufacturer.
Grounding
Clamps
Power Lines: An outdoor antenna should be located away
from power lines.
Figure 1.
Grounding Electrode
Drivin 8' Into the Earth
2.44 Meters
A) Use No. 10 AWG (5.3mm2) copper, No 8 AWG (8.4mm2) aluminum, No. 17
AWG (1.0mm2) copper clad steel or bronze wire, or larger, as ground wire.
B) Secure antenna lead-in and ground wires to house with stand-off insulators
spaced from 4 feet (1.22m) to 6 feet (1.83m) apart.
C) Mount antenna discharge unit as close as possible to where lead-in enters
house.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LS7500CD 08/03/00 2:49 PM Page 12
WARRANTY
ONE (1) YEAR LIMITED WARRANTY
OPERATION AND MAINTENANCE
Damage Requiring Service: The appliance should be serviced
by qualified service personnel when:
Magnadyne Corporation or its authorized agents will within 1 year from the
date of sale to you, repair, replace or refund the retail sales price of said
product or any part thereof, at the option of the Magnadyne Corporation or
its authorized agents, if said product or part is found defective in materials or
workmanship, when properly connected and operating on the correct power
requirements designated for the specific product. This warranty and
Magnadyne Corporation or its authorized agents obligations hereunder do
not apply where the product was; damaged while in the possession of the
consumer, subjected to unreasonable or unintended use, not reasonably
maintained, utilized in commercial or industrial operations, or serviced by
anyone other than Magnadyne Corporation or its authorized agents, or
where the warning seal on the product is broken or the power and/or plugs
are detached from the unit. Magnadyne Corporation or any of its authorized
agents will not assume any labor costs for the removal and re-installation of
any product found to be defective, or the cost of transportation to
Magnadyne Corporation or its authorized agents. Such costs are the sole
responsibility of the purchaser.
This warranty does not cover the cabinet appearance items or accessories
used in connection with this product, or any damaged to recording or
recording tape, or any damage to the to the products resulting from
improper installation, alteration, accident, misuse, abuse or acts of nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT
BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES OR CLAIMS EXCEPT THOSE ACCORDED BY LAW. NO
EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT
THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND
BEYOND 1 YEAR FROM THE DATE OF SALE.
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has spilled into the appliance;or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or
exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure
damaged.
Servicing: The user should not attempt to service the appliance
beyond that described in the operating instructions. All other
servicing should be referred to qualified service personnel.
Caution:
Compact disc should be stored in a container or vinyl bag to
prevent contamination. Disc should not be placed in locations
exposed to sunlight or heat.
Warnings
This warranty extends only to the original purchaser of the product and is not
transferable.
Some states do not allow limitations on how long an implied warranty lasts,
and some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusion may not apply
to you. This warranty gives you specific legal rights, and you may have other
rights that vary from state to state.
Handle CD’s
Properly
Do Not Touch
Do Not Get Dirt
Do Not Write on
CD’s
on CD’s
CD’s
104
40
F
C
Defective merchandise should be returned to the original point of purchase
or secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton
CA 90220, or 2061 Cohen Street, Montreal, Quebec H4R 2N7. Return
Authorization must be obtained before sending, or merchandise may be
refused.
0
Do Not Scratch
Keep Below 104
Fahrenheit
Do Not Bend CD’s
CD’s
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|