Undercounter, Prep Table
and Low Boy Refrigerators
and Freezers
Installation, Use & Care Manual
This manual is updated as new information and models are released.
America’s Quality Choice in Refrigeration
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Section 1
General Information
Model Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sandwich/Salad Prep Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pizza Prep Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Undercounter Refrigerators and Freezers . . . . . . . . . . . . . . . . . . . . . . . . .
Work Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Boy Chef Stands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Read Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Undercounters / Sandwich / Salad Prep Table Example . . . . . . . . . . . . . .
Work Table / Chef Stand Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pizza Prep Table Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model/Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Coverage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Labor Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exclusions from Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-1
1-1
1-1
1-1
1-2
1-2
1-2
1-3
1-4
1-4
1-4
1-4
1-4
1-4
Section 2
Installation Instructions
Locating the Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-1
2-2
2-2
2-3
2-3
2-3
2-3
2-4
2-5
2-6
2-6
2-6
2-6
2-6
2-6
2-7
2-7
Pre-installation Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uncrating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leveling the Cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shelf/Tray Slide Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shelves — Undercounter Units & Sandwich/Salad Units . . . . . . . . . . . . . .
Shelves — Pizza Prep Units & Refrigerated Work Tables . . . . . . . . . . . . .
Tray Slides (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condensate Water Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defrost Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defrost Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defrost Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Defrost Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting Defrost Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Part Number 14514 2/08
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents (continued)
Section 3
Operation
Sequence of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading Pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Checks and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door Hinge Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rehinging Doors — Single Door Models . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1
3-1
3-1
3-2
3-2
3-2
3-2
Section 4
Maintenance
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Condenser Coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condenser Cleaning Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Fan Blades and Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Evaporator Drain Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-1
4-1
4-1
4-1
4-2
4-2
Section 5
Before Calling for Service
Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
ii
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
General Information
WORK TABLES
Model Numbers
Refrigerated Work Tables (1 Door)
This manual covers the following models:
SANDWICH/SALAD PREP TABLES
Sandwich / Salad Prep Tables
STA-10-RSE
STS-10-RSE
STSS-20-RSE
LTS-10-RSE
STSA-10-RSE
LTA-10-RSE
Refrigerated Work Tables (2 Door)
P-6
P-10-8
P-10-12
P-15-12
P-15-16
STA-20-RSE
STSA-20-RSE
LTA-20-RSE
STS-10-RSE
STSS-20-RSE
LTS-20-RSE
Super Sandwich / Salad Prep Tables
Refrigerated Work Tables (3 Door)
ST-27-2
ST-45-3
ST-45-4
ST-59-3
ST-59-4
STA-30-RSE
STSA-30-RSE
LTA-30-RSE
STS-30-RSE
STSS-30-RSE
LTS-30-RSE
Super Prep Tables
Refrigerated Work Tables (Remote)
ST-45-12
ST-59-16
STSA-20-RRE
STSA-30-RRE
STA-20-RRE
STA-30-RRE
LTA-20-RRE
LTA-30-RRE
STSS-20-RRE
STSS-30-RRE
STS-20-RRE
STS-30-RRE
LTS-20-RRE
LTS-30-RRE
Smoothie Table
FST-45-2EN
PIZZA PREP TABLES
Pizza Prep Tables
Freezer Work Tables (1 Door)
PTA-1
PTA-2
PTA-2D
PTA-3
PTS-1
PTS-2
PTS-2D
PTS-3
STA-10-FSE
STSA-10-FSE
LTA-10-FSE
STS-10-FSE
STSS-10-FSE
LTS-10-FSE
PTA-3D
PTS-3D
Freezer Work Tables (2 Door)
STA-20-FSE
STSA-20-FSE
LTA-20-FSE
STS-20-FSE
STSS-20-FSE
LTS-20-FSE
UNDERCOUNTER REFRIGERATORS AND
FREEZERS
Freezer Work Tables (3 Door)
Refrigerated Undercounters — Solid Door Glass Door
STA-30-FSE
STSA-30-FSE
LTA-30-FSE
STS-30-FSE
STSS-30-FSE
LTS-30-FSE
R-6E
RS-6E
RSC-6E
R-10E
RS-10E
RSC-10E
R-15E
RS-15E
RSC-15E
R-10EGD
RS-10EGD
RSC-10EGD
Freezer Work Tables (Remote)
STSA-20-FRE
STSA-30-FRE
STA-20-FRE
STA-30-FRE
LTA-20-FRE
LTA-30-FRE
STSS-20-FRE
STSS-30-FRE
STS-20-FRE
STS-30-FRE
LTS-20-FRE
LTS-30-FRE
Freezer Undercounter Units
F-6E
FS-6E
FSC-6E
R-10E
FS-10E
FSC-10E
LOW BOY CHEF STANDS
Low Boy Chef Stands
LBS-2D-ST
LBS-4D-ST
LBS-6D-ST
LBS-2D-LT
LBS-4D-LT
LBS-6D-LT
LBR-2D-ST
LBR-4D-ST
LBR-6D-ST
LBR-2D-LT
LBR-4D-LT
LBR-6D-LT
Compact Low Boy Chef Stand
LBS-4DS-ST
Part Number 14514 2/08
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
Section 1
How to Read Model Numbers
UNDERCOUNTERS / SANDWICH / SALAD PREP TABLE EXAMPLE
Prefix
Body Type
Suffix
P–15–16
Undercounters
E - Series
Undercounters
R - Refrigerator
F - Freezer
Sandwich / Salad Prep Table
P - Pan top (30" depth)
ST - Supertop (34" depth)
Sandwich / Salad Prep Table
P Series
6 - 6 Pans
8 - 8 Pans
12 - 12 Pans
16 - 16 Pans
6 - 27" Wide
10 - 45" Wide
15 - 59" Wide
27 - Supertop 27"
45 - Supertop 45"
49 - Supertop 59"
ST Series
2 - 2 Cutouts, 6 Pans each
3 - 3 Cutouts, 6 Pans each
4 - 4 Cutouts, 6 Pans each
Superprep
12 - 12 Pans
16 - 6 Pans
WORK TABLE / CHEF STAND EXAMPLE
Prefix
Body Type
Suffix
STS A–30–R S E
Work Tables
ST - Stainless steel flat top
LT - Sub top
Work Tables
R - Refrigerator
STS - Stainless steel top
with backsplash
Work Tables
20 - 2 Door
S - Self-contained
E - Series
Chef Stands
30 - 3 Door
Chef Stands
LBS - Low boy chef stand
self-contained
LBR - Low boy chef stand
remote
Chef Stands
2D - 2 Drawers
4D - 4 Drawers
6D - 6 Drawers
LT - Galvanized flat top
ST - Stainless steel “V” edge top
Work Tables Only
A - Aluminum interior
S - Stainless steel interior
1-2
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
General Information
PIZZA PREP TABLE EXAMPLE
Model Prefix
Body Type
PT–A–2
1 - 1 Door
2 - 2 Door
3 - 3 Door
PT - Pizza Top Table
A - Aluminum Interior
A - Stainless Steel Interior
Part Number 14514 2/08
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
Section 1
EXCLUSIONS FROM WARRANTY
Model/Serial Number Location
1. Normal start-up, maintenance, adjustments, and
cleaning.
The McCall data plate which includes the model number
and serial number, as well as important electrical and
technical information, is located on the left interior wall of
the cabinet.
2. Damage caused by improper installation of the
McCall cabinet as outlined in this manual.
For convenience and quick reference, record the model
and serial numbers, voltage, and installation date in the
spaces below:
3. Labor charges resulting from the inaccessibility of
the McCall cabinet.
4. Damage to parts due to misuse, abuse, neglect, or
accidents.
Model Number ________________________________
Serial Number ________________________________
Voltage ______________________________________
Installation Date _______________________________
Warranty Coverage
5. Premium labor rates due to holidays, overtime,
travel time, mileage, etc., not specifically authorized
by McCall prior to service.
6. Miscellaneous tools or materials charges.
7. Repairs due to modifications to the McCall cabinet
or refrigeration system not authorized by McCall in
writing.
Warranty coverage on a McCall cabinet begins on the
date it is installed. Please read the warranty certificate
included with the cabinet for details.
8. Claims for indirect or consequential damages,
including food spoilage or product loss.
PARTS COVERAGE
1. McCall warrants the cabinet, refrigeration, and
mechanical components against defects in materials
and workmanship for a period of one (1) year from
the date of original installation.
9. Damage due to faulty or incorrect power supply,
floods, storms, or other acts or God.
WARRANTY SERVICE
To ensure warranty coverage, a qualified service
company, authorized by McCall, must perform the
warranty repair.
2. Refrigerator and freezer compressors are covered
for five (5) years from the date of original installation.
LABOR COVERAGE
If the dealer the McCall cabinet was purchased from
does not perform warranty service, please contact the
McCall Service Department for assistance.
Labor is covered for (1) year from the date of original
installation.
1-4
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
Pre-installation Checklist
Important
These instructions are of the utmost importance in
assuring that the McCall cabinet operates as
designed. Follow them closely.
Install the cabinet in an indoor environment
only.
Please call your local McCall dealer or the McCall
Service Department if you have any questions regarding
proper installation.
The air temperature entering the refrigerator or
freezer condenser should be between 55°F
(13°C) and 100°F (38°C).
Locating the Cabinet
Allow space for air circulation in the refrigeration
condensing unit compartment on refrigerators
and freezers. The minimum space requirements
are shown below.
Caution
!
When selecting a permanent location for the unit,
observe the following guidelines. Failure to do so
may cause reduced performance and efficiency,
cause damage, and/or void your warranty.
The floor must be strong enough to support the
weight of the cabinet and product load.
NOTE: A fully loaded cabinet can weigh more than
2,000 pounds.
CHEF STANDS
3.00"
(7.6 cm)
Front View
Side View
6.00"
(15.2 cm)
(Load Height)
PIZZA TABLES AND
REFRIGERATED BASES
COMPACT UNDERCOUNTERS
REFRIGERATOR AND FREEZERS
6.00"
(15.2 cm)
1.00"
(2.5 cm)
1.00"
(2.5 cm)
1.00"
(2.5 cm)
Line
Cover
Note:
1" side clearance
is recommended
on 27" and 45"
freezers.
No side clearance
is needed on
refrigerators.
Front View
Side View
Front View
Side View
6.00"
6.00"
(15.2 cm)
(15.2 cm)
(Load Height)
(Load Height)
E-3045-B
Cabinet Clearances (Typical Single Door Cabinet Shown)
Part Number 14514 2/08
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Uncrating
Section 2
!
Warning
Never attempt to tilt the cabinet alone. Always use
two or more people when tilting the cabinet to
remove the shipping skid or to move it through
doorways.
Thread Leveling
Leg into Base of
Cabinet
1. Remove the bottom shipping skid using one of the
methods below:
-
Lay the cabinet on its back, elevated and
supported by wooden blocks. Remove the skid
mounting bolts and separate the skid from the
cabinet.
-
Tilt the cabinet from side to side and remove the
mounting bolts. Support the weight of the cabinet
apart from the skid.
Thread Foot in
as Far as
2. Install the legs or casters and torque them to
360 inch-pounds (41 Nm). Refer to the drawing at
right.
Possible
3. Return the cabinet to the upright position.
4. Remove any remaining crating materials.
SV1342
Installing Cabinet Legs
Leveling the Cabinet
Caution
!
If the cabinet was placed on its back while moving it
or while removing the bottom shipping skid, wait at
least two hours after returning the cabinet to the
upright position before starting the refrigeration
system.
The cabinet must be leveled after it is positioned in its
permanent location. This insures proper door alignment
on all cabinets, adequate condensate water drainage
and proper refrigeration system operation.
Caution
!
If casters are installed instead of legs, the floor must
be leveled before final positioning of the cabinet.
Caution
!
Never use sharp instruments to cut the plastic or
cardboard crating materials. Damage to the cabinet
exterior may result.
1. Move the cabinet to its permanent location.
2. Place a level on top of the cabinet.
3. Turn the leveling foot of the lowest corner leg to
center the bubble in the level.
4. Adjust each of the other corners until the bubble is
centered and the cabinet is stable.
5. Re-check the cabinet from side to side and from
front to rear with the level.
2-2
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
TRAY SLIDES (OPTIONAL)
Shelf/Tray Slide Installation
Refrigerated pizza tables include a chrome plated steel
pan or tray rack (Model RA-11-T) behind one door
opening on 2- and 3-door models. All other tray slides for
pizza tables and refrigerated work tables are optional
accessories and are included only when ordered. To
install a tray slide:
SHELVES — UNDERCOUNTER UNITS & SANDWICH/
SALAD UNITS
Shelf clips are factory-installed on undercounter
refrigerators and freezers, and on regular and super top
sandwich/salad prep units.
To install the shelves, simply unpackage the shelves
from the cardboard container and place one on each set
of clips.
1. Locate the appropriate square shelf standard holes
at the desired height.
2. Insert the tabs of each slide into the 3/8" holes in the
shelf support standards and pull it straight down to
lock it into place (refer to drawing below).
SHELVES — PIZZA PREP UNITS & REFRIGERATED
WORK TABLES
Pizza prep units and work tables are factory-fitted with
shelf support standards. The shelf clips are packaged
separately and must be installed as shown in the
drawing below.
Extensions are required when using
18" wide (left to right) trays or pans
Four shelf clips are required for each shelf. Make sure
that the clips are level side-to-side and front-to-rear.
Place one shelf on each set of clips.
Shelf
Support
Standard
Tray
Slide
Note: Shelf support
standards are shown
outside for clarity.
SV1342
Tray Slide Installation
Shelf Installation
Part Number 14514 2/08
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Electrical
Section 2
As a rule, the power lines must be enclosed inside a
conduit secured to the power junction boxes on both
ends.
All cord-connected units must be plugged into a
grounded and properly sized electrical outlet with
appropriate overcurrent protection. Refer to the drawing
below for electrical plug configurations.
NOTE: Power installation must be in compliance with the
National Electrical Code and all applicable local and
state codes.
!
Warning
Never use an extension cord.
Never alter the power cord or plug supplied with the
cabinet. Failure to follow this warning could result in
serious injury or death.
After the power source has been connected, turn on the
main power switch. The switch is located on the cabinet
top, behind the front louvered panel.
5-20P
5-15P
SER.4
5-20P and 5-15P Electrical Plug Configurations
All permanently connected (hard wired) units are fitted
with a power junction box and 6" pigtail wires for power
connection.
Connect one end of the power line to the pigtail from the
cabinet junction box. Connect the other end to a properly
sized electrical source.
2-4
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
ELECTRICAL SPECIFICATIONS
Product
Type
Self-Contained
Voltage/Cycles/
Phase
Total
Amps
Maximum
ANSI Electrical
Plug Configuration
Base Models
R-6E, RS-6E, RSC-6E
R-10E, RS-10E, RSC-10E
R-15E, RS-15E, RSC-15E
F-6E, FS-6E, FSC-6E
F-10E, FS-10E, FSC-10E
RP-6EN
Fuse Size
15 amp
15 amp
15 amp
15 amp
15 amp
15 amp
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
6.0
8.0
6.0
8.0
8.5
6.0
NEMA 5-15
NEMA 5-15
NEMA 5-15
NEMA 5-15
NEMA 5-15
NEMA 5-15
Undercounter
Refrigerators
Undercounter
Freezers
RP-10-6EN, RP-10-8EN,
RP-10-12EN
115/60/1
8.0
15 amp
NEMA 5-15
RP-15-8EN, RP-15-12EN,
RP-15-16EN
115/60/1
115/60/1
115/60/1
10.0
6.0
15 amp
15 amp
15 amp
NEMA 5-15
NEMA 5-15
NEMA 5-15
RST-27-2EN
RST-45-2EN, RST-45-3EN,
RST-45-12EN
8.0
RST-59-3EN, RST-59-4EN,
RST-59-16EN
Sandwich/Salad
Units
115/60/1
115/60/1
10.0
7.0
15 amp
15 amp
NEMA 5-15
NEMA 5-15
LTA-10-RSE, LTS-10-RSE,
STA-10-RSE, STS-10-RSE,
STSA-10-RSE, STSS-10-RSE
LTA-20-RSE, LTS-20-RSE,
STA-20-RSE, STS-20-RSE,
STSA-20-RSE, STSS-20-RSE
115/60/1
115/60/1
10.0
12.0
7.0
15 amp
15 amp
15 amp
15 amp
15 amp
NEMA 5-15
NEMA 5-15
NEMA 5-15
NEMA 5-15
Hard Wired
LTA-30-RSE, LTS-30-RSE,
STA-30-RSE, STS-30-RSE,
STSA-30-RSE, STSS-30-RSE
LTA-10-FSE, LTS-10-FSE,
STA-10-FSE, STS-10-FSE,
STSA-10-FSE, STSS-10-FSE
115/60/1
Refrigerated
Work
LTA-20-FSE, LTS-20-FSE,
STA-20-FSE, STS-20-FSE,
STSA-20-FSE, STSS-20-FSE
Tables
115/60/1
12.0
11.8
LTA-30-FSE, LTS-30-FSE,
STA-30-FSE, STS-30-FSE,
STSA-30-FSE, STSS-30-FSE
208-230/60/1
LBS-2D-ST, LBS-2D-LT
LBS-4D-ST, LBS-4D-LT
LBS-6D-ST, LBS-6D-LT
PTA-10, PTS-10
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
7.0
15 amp
15 amp
15 amp
15 amp
15 amp
20 amp
NEMA 5-15
NEMA 5-15
NEMA 5-15
NEMA 5-15
NEMA 5-15
NEMA 5-20
Low Boy
Chef
Stands
10.0
12.0
10.0
12.0
16.0
Pizza
Prep
Tables
PTA-20, PTS-20
PTA-30, PTS-30
Part Number 14514 2/08
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
Condensate Water Removal
McCall cabinets are equipped with condensate vaporizer
systems.
Remote units use an electrically operated system.
Most self-contained units use either an energy-free
automatic type or an electrically-operated type. No drain
connection is required.
Defrost Systems
GENERAL
Refrigerator coils are kept below the freezing point
(32°F). During compressor off time, the evaporator fan
continues to circulate 38°F refrigerator compartment air
through the evaporator coil. This air circulation raises the
coil temperature above the freezing point, melting any
accumulated frost. The run-off water is drained into the
vaporizer pan and is evaporated.
Freezer coils are defrosted electrically.
NOTE: A freezer’s evaporator fans do not run
immediately upon start-up or during and immediately
following the defrost cycles. The fans start when the coil
reaches a cold temperature. This prevents the fans from
blowing heated air on the stored products.
DEFROST TIMERS
Defrost Timer
Important
Set the defrost timer to defrost the cabinet during
the lowest usage periods.
Undercounter freezer models F-10E, FS-10E, and
FSC-10E use an adjustable defrost timer which may be
custom-set to initiate defrost periods. All other models
use non-adjustable freezer defrost timers, which
automatically initiate at pre-set intervals and for a
pre-determined duration.
SETTING DEFROST TIME
DEFROST SETTINGS
The defrost timer must be set to real time after the power
is turned on, or after a power failure.
The defrost timer is factory preset to defrost the
evaporator coil each day at 2:00 AM, 8:00 AM,
2:00 PM, and 8:00 PM.
To set the time:
If you wish to change the defrost times, remove the pins
from the outer dial and re-insert them into the desired
time slots. (Refer to drawing.)
1. Grasp the knob in the center of the inner dial.
2. Turn it counterclockwise to rotate the outer dial.
3. Line up the current time of day on the outer dial with
the pointer.
Caution
!
Leave at least one hole between adjacent pins.
2-6
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Installation Instructions
Important
Setting the temperature control to the coldest setting
may cause the coil and/or air ducts to freeze and ice
up. This will eventually result in a warmer cabinet
temperature.
ADJUSTING DEFROST DURATION
The defrost cycle is terminated by a temperature-
sensing switch located on the suction line, adjacent to
the evaporator coil.
The defrost duration is factory-set. Normally, no
adjustment is required. For a longer defrost time, press
down on the inner dial pointer and rotate the pointer until
the desired time lines up.
If ice accumulation occurs and the temperature is
lower than the guidelines, turn the control knob to a
warmer setting.
Important
The coil defrosts only until the temperature-sensing
switch terminates the cycle, regardless of the
defrost duration that is set.
Caution
!
Allow the cabinet to reach proper operating
temperature before filling it with product. Do not
place hot or steaming foods in the cabinet.
TEMPERATURE CONTROLS
The temperature controls are factory-set to maintain an
average temperature of 38°F in refrigerators, and an
average temperature of 0°F in freezers.
Caution
!
Store products with high acid content (such as
lettuce, other fresh vegetables or fruits, salad
dressings, etc.) in closed containers. This will
prevent corrosion on the evaporator coil and other
metal parts in the air distribution system.
The temperature variance is 6-8 degrees. A freezer
should run between -2 to -3°F and +3 to +4°F. A
refrigerator should run between +35 to +36°F and +41 to
+42°F.
For a different cabinet temperature setting, turn the
temperature control knob or screw, located on the
evaporator coil/blower housing.
Part Number 14514 2/08
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Section 2
THIS PAGE INTENTIONALLY LEFT BLANK
2-8
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
Operation
Sequence of Operation
Important
LOADING SHELVES
Uncovered food will dehydrate much more rapidly
than covered food. For best food quality, always
store in covered container.
For maximum operating efficiency, load the shelves with
space between the stored items. This allows air to
circulate properly. Refer to the drawings below.
LOADING PANS
Caution
!
Pan-top refrigerators are designed for operation with all
pans in place, even if some pans are to be left empty.
For maximum food freshness, fill the pans only with an
amount than can be used in a specific usage period
(breakfast, lunch, dinner, etc). During non-use or
slow-use periods, close the lid cover.
Store products with high acid content (such as
lettuce, other fresh vegetables or fruits, salad
dressings, etc.) in closed containers. This will
prevent corrosion on the evaporator coil and other
metal parts in the air distribution system.
Supply Air
Evaporator Fan
Supply Air
Shelf
Evaporator Coil
Evaporator Coil
Return Air
Shelf
Compressor
COMPACT UNDERCOUNTER
REFRIGERATOR AND FREEZERS
Return Air
Evaporator Coil
Return Air
Supply Air
Shelves
CHEF STANDS
PIZZA TABLES AND
REFRIGERATOR BASES
0301
Loading the Shelves
Part Number 14514 2/08
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Section 3
Operating Checks and Adjustments
HingePin
Screw
DOOR HINGE ADJUSTMENT
1. Loosen 2 Phillips head screws on the top and
bottom hinges where the hinges fasten to the
cabinet exterior front facing.
Hinge Mechanism
Mounting Screws
2. Firmly press the door tight to the cabinet front while
re-tightening the hinge screws.
Hinge Pin
NOTE: For some adjustments, it may be necessary to
add shims behind the hinges.
REMOVING DOORS
Remove 2 Phillips head screws from the top door hinge
and 2 Phillips head screws from the bottom hinge.
Carefully lift the door off the cabinet front.
REHINGING DOORS — SINGLE DOOR MODELS
McCall’s one door models are factory-shipped hinged on
the right side (facing the unit front). If it becomes
necessary to change the hinging on a door:
Removable
Mechanism
1. Remove 2 Phillips head screws from the top and
bottom door hinges.
0302
Hinge Removal
2. Carefully lift the door off of the cabinet.
3. Remove the (3) screws securing the door handle
and remove the handle.
4. Turn the door 180 degrees.
5. Attach handle at the position indicated by the pre-
punched mounting holes.
6. Remove the hinges from the door as shown in the
drawing.
7. Position and attach the new hinge
(Part #HAH-0702-001 for the top hinge,
Part #2HAH-0704-001 for the bottom hinge).
8. Remove and reposition the hinge cartridge
mechanism.
9. Attach the door to the cabinet using the screws
removed earlier.
10. Perform the “Door Hinge Adjustment” procedure
above.
3-2
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Maintenance
Cleaning
Cleaning the Condenser Coil
EXTERIOR
!
Warning
Clean cabinet exterior surfaces with a solution of mild
soap and water. To minimize streaking, follow with a
fresh water rinse.
Disconnect electric power before cleaning. Failure
to follow this warning could result in serious injury or
death.
If stainless steel becomes discolored, scrub only in the
direction of the finished grain.
For efficient operation, it is very important to clean the
condenser coil surface and keep it free of dust, dirt, and
lint. McCall recommends checking the condition of the
condenser coil once a month.
For high shine, see your kitchen equipment dealer for a
high-quality stainless steel polish.
Caution
!
The condensing unit fan draws dust, lint and small
particles to the condenser coil, where it forms a “blanket”
on the coil surface. This is normal and should be
periodically removed.
Do not use steel wool, caustic soap, or abrasive
cleaners, as these may damage the metal finish.
Alcohol-based cleaners may damage the nylon door
cams.
Caution
!
If the cabinet has a synthetic cutting board, remove it by
simply lifting the board straight up. Make sure the board
and the metal cabinet surface are completely dry before
replacing the cutting board.
Failure to clean and maintain the condenser coil
properly will result in reduced air circulation through
the condenser fins. This will cause reduced
efficiency, high operating pressures, and can
shorten compressor life.
The condensate evaporator pan, located underneath the
cabinet, should be cleaned periodically with soapy water
to remove any mineral deposits.
CONDENSER CLEANING PROCEDURES
INTERIOR
One or more of the following methods may be used to
clean the condenser coil surface, depending upon the
extent of the build-up on the fins.
Clean cabinet interior surfaces with warm water and
baking soda, applied with a cloth or sponge.
The air duct and shelf support standards can be
removed without special tools to facilitate cleaning.
!
Warning
Condenser fins are sharp. Use care when working
around them.
Wash door gaskets weekly with a mild soap and water
solution, followed by a fresh water rinse.
While cleaning, check the door gaskets for proper
sealing. Adjust if needed.
Method 1
Remove light build-up with a soft brush or a vacuum with
a brush attachment. Brush the condenser fins from top
to bottom, not from side to side. Shine a light through the
fins to check for dirt inside the condenser.
Caution
!
Do not clean cabinet interior surfaces with any
cleaning product not specifically approved for use
where food may come into contact.
Method 2
Clean moderately dirty fins with compressed air, blowing
from the inside out. Follow by brushing, if necessary.
Caution
!
Method 3
Do not use steel wool, caustic soap, or abrasive
cleaners, as these may damage the metal finish.
Clean with a commercial condenser coil cleaner,
available from a kitchen equipment dealer. Follow the
directions and precautions supplied with the cleaner.
Part Number 14514 2/08
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Section 4
After cleaning, straighten any bent condenser fins with a
fin comb.
CLEANING THE FAN BLADES AND MOTOR
If necessary, clean the fan blades and motor with a soft
cloth. If it is necessary to wash the fan blades, cover the
fan motor to prevent moisture damage.
Comb
Down Only
CLEANING THE EVAPORATOR DRAIN PAN
Fin Comb
The evaporator drain pan, located at the bottom of the
evaporator blower panel, should be cleaned periodically
to remove any food, debris, etc. that may have fallen or
been drawn into the pan.
Condenser
To clean the pan drain outlet, gently insert a pliable wire,
such as a pipe cleaner, 3-4" (7-10 cm) into the mouth of
the outlet. Remove any obvious debris in the pan
bottom.
fin_comb
Using a Fin Comb
4-2
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
Before Calling for Service
Troubleshooting Guide
If a problem arises during operation of your refrigerator
or freezer, follow the checklist below before calling
service. Routine adjustments and maintenance
procedures are not covered by the warranty.
!
Warning
Disconnect electric power before performing any
service. Failure to follow this warning could result in
injury or death.
Problem
Cabinet not running
Possible Cause
Fuse blown or circuit breaker tripped.
To Correct
Replace fuse or reset circuit breaker.
Plug in power cord.
Power cord unplugged.
Thermostat set too high.
Main power switch turned off.
Set thermostat to lower temperature.
Turn main power switch on.
Wait for defrost cycle to finish.
Cabinet in defrost cycle.
(Freezer models)
Condensing unit runs
for long periods or
continuously
Excessive amount of warm product
placed in cabinet.
Allow adequate time for product to cool
down.
Prolonged door openings or door(s) ajar. Make sure door(s) are closed when not in
use. Avoid prolonged door openings.
Door gasket(s) not sealing properly.
Check gasket condition. Adjust door or
replace gasket if necessary.
Dirty condenser coil.
Clean the condenser coil.
Evaporator coil iced over.
Turn unit off and allow coil to defrost.
Make sure thermostat is not set too cold.
Also, check gasket condition.
Cabinet temperature
is too high
Thermostat set too high.
Set thermostat to lower temperature.
Poor air circulation in cabinet.
Re-arrange product to allow proper air
circulation.
Exterior thermometer is out of calibration. Re-calibrate thermometer.
Excessive amount of warm product
placed in cabinet.
Allow adequate time for product to cool
down.
Prolonged door openings or door(s) ajar. Make sure door(s) are closed when not in
use. Avoid prolonged door openings.
Dirty condenser coil.
Clean the condenser coil.
Evaporator coil iced over.
Turn unit off and allow coil to defrost.
Make sure thermostat is not set too cold.
Also, check gasket condition.
Cabinet is noisy
Loose part(s).
Locate and tighten loose part(s).
Tubing vibration.
Insure tubing is free from contact with
other tubing or components.
Refrigerator is freezing product
Compressor will not
start — hums and trips on overload
protector
Thermostat is set too low.
Dirty condenser coil.
Set thermostat to higher temperature.
Clean the condenser coil.
Not enough cabinet clearance for proper Move cabinet or make other adjustments
refrigeration system operation.
to gain proper cabinet clearances.
Low voltage to cabinet.
Check and correct incoming voltage to
cabinet.
Part Number 14514 2/08
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Calling for Service
Section 5
THIS PAGE INTENTIONALLY LEFT BLANK
5-2
Part Number 14514 2/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2008 Manitowoc
Continuing product improvements
may necessitate change of
specifications without notice.
Part Number 14514 2/08
McCall Refrigeration, Inc.
81 West Holly Street
Parsons, TN 38363, USA
Ph: 731-847-5365 Fax: 731-847-9012
Visit us online at: www.manitowocfsg.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|