M Audio Computer Hardware 1010LT User Manual

Delta 1010LT - Users Manual  
Version: D1010LT-121002  
Table of Contents  
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
What’s in the Box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
About the Delta 1010LT Digital PCI Audio Card . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3  
Product Features & Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Breakout Cable 1: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Setting the Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
Windows XP,2000, and ME Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Windows 98 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10  
Windows 95 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10  
Windows NT Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
Verifying Windows Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
Verifying Delta Control Panel Software Installation in Windows . . . . . . . . . . . . . .12  
Delta Driver Software Installation on the Mac . . . . . . . . . . . . . . . . . . . . . . . . . . . .13  
Delta Control Panel Installation on the Mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14  
Delta System Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14  
Delta’s Analog Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14  
The Digital Monitor Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15  
The Patchbay / Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15  
Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15  
Using the Delta 1010LT with your Music Software Application . . . . . . . . . . . . . . .16  
Delta 1010LT Control Panel Software - PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
Monitor Mixer Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
Patchbay/Router Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22  
Hardware Settings Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
S/PDIF Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27  
About Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28  
Save, Delete, Load Buttons; H/W Installed . . . . . . . . . . . . . . . . . . . . . . . . . . .28  
Delta 1010LT Control Panel Software - Mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29  
Patchbay/Router Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31  
Hardware Settings Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33  
S/PDIF Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37  
Delta 1010LT Recording Tutorials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39  
Typical Setup #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39  
Typical Setup #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45  
Transferring from DAT to Delta 1010LT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46  
Transferring from 1010LT to DAT, monitoring with DAT . . . . . . . . . . . . . . . .47  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49  
Troubleshooting Tips for Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . .52  
Before You Call Midiman/M-Audio Technical Support . . . . . . . . . . . . . . . . . . . . . .53  
Appendix A - Technical Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56  
Appendix B-If You Use An External Mixer... . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57  
Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Within the Delta 1010LT’s PCI chip is a hardware digital mixer. Controlled by the Delta  
Control Panel software, it may handle all of your mixdown needs, give you extra control  
of all left, right and stereo levels plus pans, solos, and mutes, or simply give you an  
alternate or headphone mix.  
Quick Start Guide  
There may not be any instant tips or tricks for understanding and using an audio interface  
that is as versatile as the Delta 1010LT. However, we may be able to include some  
“straight talk” to help light the way.  
On the PC: Following the installation procedures for both the Delta hardware and  
software will enable the 1010LT for use in Windows. The Delta 1010LT will become your  
Windows sound card simply by going to My Computer | Control Panel | Multimedia, and  
changing Audio settings to one of the Delta stereo pairs. In this way, the Delta card will  
be the default audio device for your Windows and other media players.  
On the Mac: Following the installation procedures for both the Delta hardware and  
software will enable the 1010LT to be configured for use in a music program that utilizes  
the ASIO drivers supplied with the Delta. Additionally, the Delta 1010LT can be used in  
the Apple Sound Manager for your system sounds or in a music/recording program that  
directs itself to the Sound Manager. The Delta 1010LT will become your Macintosh’s  
audio device simply by going to the Apple menu | Control Panel | Sound, and changing  
audio settings from “built-in” to the Delta. In this way, the Delta card will be the default  
audio device for your Apple applets and a variety of media players. If you wish only to  
use the Delta with an ASIO compliant music program, leave this setting on “built-in.”  
You will, however, need a music/recording software application to take full advantage of  
the Delta 1010LT as a production tool, and most likely that software will need to analyze  
and configure the Delta 1010LT--this usually occurs when first launching the program  
after the Delta 1010LT has been installed. On the PC, the 1010LT is also capable of  
playing an encoded surround sound signal from the S/PDIF output using some of the  
DVD player applications that exist on the market. This usually takes some audio output  
configuration within the player.  
The Delta Control Panel controls many of the card’s settings, and includes controls for the  
digital mixer that is contained on the Delta card. While all of those settings may seem daunting  
at first, it may help to know that by using only the default settings, the card is ready to playback  
audio files from your computer (the control panel is set to play audio outputs from software).  
This can be done from a media player or from your music application, provided the outputs  
are set to a Delta output port and the software and card are properly configured.  
You will be able to hear the Delta inputs under certain conditions. Using a recording  
program that utilizes the ASIO or EASI drivers with the Delta 1010LT, or (in Windows)  
using the Windows WDM drivers with programs that take full advantage of them, will allow  
you to monitor the Delta inputs through the program, and thereby continue to use the default  
settings in the Delta Control Panel (as mentioned, these are audio outputs from software).  
When using the Delta card and monitoring in this fashion, there is always some degree of  
latency, or delay between the the actual input signal and the monitoring of that input signal.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Another way to approach this is by directly monitoring those inputs. This can be done in  
the Delta Control Panel’s “Patchbay/Router” page by selecting the Delta input and  
connecting it directly to the Delta output. You can also use the Delta panel’s Monitor  
Mixer to send the signal at the inputs to the Delta outputs, as well as mix those signals  
with the software outputs, i.e., your music software sending audio to the Delta outputs.  
This, and other recording/monitoring scenarios are covered in the Tutorials section toward  
the end of the manual.  
Product Features & Specifications  
10x10 24-bit/96khz full-duplex recording interface.  
PCI host card with two external, color-coded breakout cables.  
8x8 analog I/O, balanced on female XLR and unbalanced on gold-plated RCA  
connectors, with output line level adjustments selectable within the Delta Control Panel.  
The two balanced analog inputs can be set via hardware jumpers to accept  
microphone level signals or line level signals.  
S/PDIF digital I/O supports a variety of settings, including AC3 or DTS surround  
(PC only) and copy protection schemes, which can be set via the Delta Control Panel.  
External synchronization up to 100kHz via word clock I/O on BNC connectors.  
1x1 MIDI I/O on standard DIN jacks.  
High dynamic range (A-weighted measured): D/A 101.5 dB, A/D 99.6 dB.  
Low distortion (measured THD @ 0dBFS): A/D and D/A less than 0.002%.  
Frequency Response: 22-22kHz, -0.2,-0.4dB @48kHz; 22-40kHz,-0.2,-0.7dB @96kHz  
All data paths support up to 24bit/96kHz performance, no upgrades necessary.  
Comprehensive digital mixing, routing, and monitoring capabilities with  
included Delta Control Panel software.  
Hardware sample-accurate sync will allow linking of multiple Delta units via S/PDIF.  
Windows XP, 2000/ME and 95/98 multi-card, multi-client drivers with ASIO1  
and ASIO2 multi-card, GSIF and EASI drivers included; Windows NT  
multi-card drivers also included.  
Macintosh control panel and drivers with ASIO1, ASIO2, and legacy ASIO  
support for OS 8.5.1 or higher.  
Minimum System Requirements  
Windows  
Windows 95, 98, NT, ME, 2000 or XP  
Pentium III 500Mhz - (96kHz operation)  
Pentium II 400 - (48kHz operation)  
128 MB of RAM - (96kHz operation)  
64 MB of SDRAM - (48kHz operation)  
UDMA EIDE  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Macintosh  
128 MB of RAM for 96kHz operation.  
64MB SDRAM for 48kHz or less.  
Mac G3 with 128 MB of RAM recommended. Some faster Power PCs will  
perform adequately.  
Mac OS 8.5.1 or higher.  
UDMA EIDE or fast SCSI HDD recommended.  
Breakout Cable 1:  
1. Word Clock Input: This female BNC connector is used to input word clock  
signals from external sources. The Delta 1010 is capable of synchronizing its  
sample rate with that of the incoming word clock signal. The input provides  
built-in 75-ohm termination. The use of 75-ohm coaxial cables (with male  
BNC connectors) is highly recommended. The connector cover is tan in color.  
2. Word Clock Output: This female BNC connector outputs a word clock signal that  
is in-sync with the present sample rate clock of the Delta 1010. The output  
circuitry is designed to drive a word clock signal across 75-ohm coaxial cables and  
into a device with 75-ohm termination. This connector cover is black in color.  
3. Coaxial S/PDIF Input: This RCA connector receives a S/PDIF stereo signal  
from your coaxial S/PDIF digital source such as a DAT, MiniDisc player or  
external A/D converter. This cable is tan in color to denote input, with the  
connector cover colored red to designate it as a digital input.  
4. Coaxial S/PDIF Output: This RCA connector sends a S/PDIF stereo signal to  
your coaxial S/PDIF digital target device such as a DAT, MiniDisc player or  
external D/A converter. This cable is black in color, denoting output.  
5. MIDI Input jack: This standard MIDI connector accepts a standard MIDI cable.  
Typically a MIDI controller or MTC source would be connected to the  
Delta 1010LT’s MIDI input jack. The cable is tan in color.  
6. MIDI Output jack: This standard MIDI connector accepts a standard MIDI  
cable. Typically a MIDI keyboard or sound module would be connected to the  
MIDI output jack. The cable is black in color.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
C
Breakout Cable 2:  
7. Host Cable connector: This 44-pin female D-sub connector is used to attach  
the breakout cable to the PCI host card’s male D-sub connector.  
8. Analog Inputs 3-8: These jacks input analog audio from a variety of external  
sources. Each jack is RCA coaxial and is compatible with RCA coaxial  
(unbalanced) connections. These cables are tan in color, with the jacks colored  
white for left and red for right for each stereo pair.  
9. Analog Outputs 1-8: These jacks output analog audio to a variety of external  
targets. Each jack is RCA coaxial and is compatible with RCA coaxial  
(unbalanced) connections. These cables are black in color, with the jacks  
colored white for left and red for right for each stereo pair.  
10. Analog Inputs 1-2: These jacks input analog audio from a variety of external  
sources. Each jack is female XLR and is compatible with two-conductor  
(typically XLR or TRS) balanced connections. Inputs 1&2 can be set via  
jumpers on the PCI card to accept either line level or mic level signals. These  
cables are tan in color, with the jacks colored white for left and red for right.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PCI Host Adapter Card:  
11. Host Cable connector 1: This 15-pin D-sub connector attaches to the supplied  
breakout cable #1 to allow communication between the PCI host card and  
external digital devices.  
12. Host Cable connector 2: This 44-pin D-sub connector attaches to the supplied  
breakout cable #2 to allow communication between the PCI host card and  
external analog devices.  
13. Line Level Jumper #1: This jumper set allows you to switch the XLR analog  
input #1 level setting from balanced microphone level to a +4dBu line level  
setting. The default setting shown is the microphone level setting.  
14. Line Level Jumper #2: This jumper set allows you to switch the XLR analog  
input #2 level setting from balanced microphone level to a +4dBu line level  
setting. The default setting shown is the microphone level setting.  
Setting the Jumpers  
The Delta 1010LT’s PCI card has two sets of jumpers that can be used to control the  
operating line level for the 1010LT’s analog inputs 1&2 on XLR jacks. The location of  
these jumpers is illustrated in the previous section under “PCI Host Adapter Card.”  
Two basic settings are possible, one for a microphone line level compatible with  
low impedance dynamic microphones (those that do not require phantom power,  
such as condenser mics), and the other is an operating line level of +4dBu  
(typical for balanced line levels). Two variations are possible for each of these  
line level settings. This is shown in the illustrations below.  
The default setting when you receive your 1010LT is with the jumpers set to the  
microphone line level setting. If you wish to use either or both inputs 1&2 as a +4dBu  
line level input, then you will need to change the jumper setting on the 1010LT PCI card.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the jumper setting is easy to do when the 1010LT PCI card is not  
installed in the computer. Since it is usually impossible to change the jumpers  
while the card is in the computer, it’s a good idea to make a decision now. If you  
wish to connect a dynamic or ribbon microphone directly to the Delta 1010LT’s  
XLR analog inputs 1&2, then leave the jumpers set to their default setting,  
+4dBu. If you wish to connect the XLR analog inputs 1&2 to the output of a  
balanced +4dBu device such as a pre amp or dynamics processor, you will need  
to change the jumper setting.  
Remember that you can change one set of jumpers and not the other, if that suits  
your needs. To change the jumper:  
1. Before removing the Delta 1010LT PCI host card from its protective anti-static bag,  
touch the metal power supply case of the computer in order to dissipate any static  
electricity your body may have accumulated. You might want to pick up a grounding  
wrist strap (available from electronics stores like Radio Shack) if you want to be  
doubly sure you aren't carrying a static charge that could damage the card.  
2. Either hold the PCI card in your hand, or place it on an anti-static surface  
(such as its protective bag). Using your fingertips or a tweezer, remove the  
plastic jumper that is covering the top-most and middle metal pins. See  
Illustrations 1 and 1a, below.  
3. Place the jumper over the middle and bottom-most metal pins. See  
Illustrations 2 and 2a, below.  
1
1A  
2
2A  
Mic Level  
+30dB gain  
Mic Level  
Attenuates  
+30dB by  
11dB (i.e.,  
+19dB gain)  
Line Level  
+14dBu peak Changes  
(+4 mode)  
Line Level  
Line Level to  
+3dBu peak  
(+4 mode)  
NOTE: Illustrations 1a and 2a show a variation on the mic level  
setting and the line level setting, respectively. If you find that your  
signal is too hot using the +4dBu selection in the Delta Control  
Panel’s “Variable Signal Level” section of the Hardware Settings  
page, then try these alternate settings.  
Hardware Installation  
To mechanically install the Delta 1010LT, do the following:  
1. Turn off your computer and unplug the AC cord.  
2. Remove the computer’s cover and position the computer so that you may  
easily access its PCI slots.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Select the PCI slot where you will install your Delta 1010LT PCI host card.  
Make sure the slot is a PCI slot. If you don't know what "PCI slot" means,  
check the owner’s manual for your computer. PCI slots are distinguishable  
from ISA slots by being shorter and set back farther from the outside of the  
computer, however some newer computers have only PCI slots.  
4. Before removing the Delta 1010LT PCI host card from its protective anti-static bag,  
touch the metal power supply case of the computer in order to dissipate any static  
electricity your body may have accumulated. You might want to pick up a grounding  
wrist strap (available from electronics stores like Radio Shack) if you want to be  
doubly sure you aren't carrying a static charge that could damage the card.  
5. Remove the metal bracket that covers the access hole on the back of the  
computer. This bracket is usually fastened to the computer with a single screw.  
6. Position the Delta 1010LT PCI host card over the target PCI slot and fit the card  
loosely over it with the card in the upright position. Press the card gently but  
firmly downward into the slot until the card is completely and squarely seated  
in the slot. If the card seems difficult to seat, a slight rocking motion may help.  
7. Screw the Delta 1010LT PCI host card’s metal bracket down into the screw hole  
on the back of your computer using the screw you removed in step 5 above.  
8. Place the cover back on your computer.  
IMPORTANT: Complete the attachment of your Delta 1010LT  
breakout cables to the PCI card before powering up your computer.  
Never attach a breakout cable to the PCI card while the computer  
is on. Doing so could damage the PCI card and void the warranty.  
With your computer turned off, it is now time to connect the Delta 1010LT breakout  
cables to the PCI host card that you have just installed. You may at this time also want to  
connect to audio gear that you using in conjunction with your Delta 1010LT.  
Delta Driver Software Installation - for PC  
The Delta 1010LT system includes a driver CD for Windows XP/2000/ME/98/95/NT (and  
Macintosh, too), containing all Windows drivers and Delta Control Panel software. To install  
these on your system, please follow these steps:  
Windows XP,2000, and ME Installation  
1. After installing the Delta 1010LT hardware, boot your system and start  
Windows. During the Windows boot procedure, new hardware will be  
automatically detected by the Add New Hardware Wizard announcing “New  
Hardware Found.” Click ‘Next>’.  
2. The ‘Add New Hardware Wizard’ will now ask how you want to find the  
driver. "Search for the best driver for your device" is already selected. Click  
‘Next>’.  
3. Windows will give you a selection of locations to search. Make sure that only  
“Choose a Path” is checked, or click on the check box to do so. Insert the Driver  
CD into your CD ROM drive. Type in the drive letter of your CD drive (we will  
assume here that it is D:\) and the path to the Delta drivers, which will be  
D:\Delta Series\Wdm. Click ‘Next>’.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. The ‘Wizard’ reports that its Windows driver file search has found the  
M-Audio Delta 1010LT. Click Next>. If announcements that “No Driver  
Signature” pop up, ignore them and continue with the installation procedure.  
5. Windows is now ready to install the driver files from the specified location.  
Click Next>. Windows will start to copy the files and show you a progress  
report screen.  
6. The Wizard reports that Windows has finished installing the software. Click  
‘Finish’. Your Delta 1010LT is ready for action.  
After completion of the driver installation, Windows may require you to restart. If it does  
request a restart, remove the Drivers CD Disk from the CD drive and respond “Yes.” The  
system will restart and your Delta 1010LT is ready for play.  
Windows 98 Installation  
1. After installing the Delta 1010LT hardware, boot your system and start  
Windows. During the Windows boot procedure, new hardware will be  
automatically detected by the Add New Hardware Wizard. Click ‘Next>’.  
2. The ‘Add New Hardware Wizard’ will now ask how you want to find the driver.  
"Search for the best driver for your device" is already selected. Click ‘Next>’.  
3. Windows will give you a selection of locations to search. Make sure that only  
“Choose a Path” is checked, or click on the check box to do so. Insert the  
Driver CD into your CD ROM drive. Type in the drive letter of your CD drive  
(we will assume here that it is D:\) and the path to the Delta drivers, which  
will be D:\Delta Products\Delta98. Click ‘Next>’.  
4. The ‘Wizard’ reports that its Windows driver file search has found the  
M-Audio Delta 1010LT. Click Next>.  
5. Windows is now ready to install the driver files from the specified location.  
Click Next>. Windows will start to copy the files and show you a progress  
report screen.  
6. The Wizard reports that Windows has finished installing the software. Click  
‘Finish’. Your Delta 1010LT is ready for action.  
After completion of the driver installation, Windows may require you to restart. If it does  
request a restart, remove the Drivers CD Disk from the CD drive and respond “Yes”. The  
system will restart and your Delta 1010LT is ready for play.  
Windows 95 Installation  
1. After installation of the Delta 1010LT hardware, boot your system and start  
Windows. During the Windows boot procedure, new hardware will be  
automatically detected.  
2. Choose the Install of "driver from disk provided by hardware manufacturer,"  
then click OK.  
3. An ‘Install From Disk’ will prompt you to copy files from the  
A:\ drive. Insert the Driver software CD into your CD ROM drive. Type in the  
drive letter of your CD drive (we will assume here that it is D:\) and the path  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
to the Delta drivers, which will be D:\Delta Products\Delta98 (these drivers  
also work in Win95). Click ‘Next>’.  
4. Windows will start to copy files, with a progress indicator on the screen. Once  
this process completes itself, your Delta 1010LT will be ready for action.  
After completion of the driver installation, Windows may require you to restart. If it does  
request a restart, remove the Drivers CD Disk from the CD drive and respond “Yes.” The  
system will restart and your Delta 1010LT is ready for play.  
Windows NT Installation  
1. Power up your computer after physically installing the Delta 1010LT interface  
card.  
2. Go to Start | Settings | Control Panel and double click on ‘Multimedia.’  
3. Click the ‘Devices’ tab, then click the ‘Add’ button.  
4. “Unlisted or Updated Driver" will be highlighted at the top of the list. Click  
OK.  
5. The ‘Install Driver’ box will prompt you to insert the driver disk, and the A:  
prompt will appear as the path. Insert the Drivers CD into your CD ROM  
drive. Type in the drive letter of your CD drive (we will assume here that it is  
D:\) and the path to the Delta drivers, which will be D:\Delta  
Products\DeltaNT. Click OK.  
6. The "M Audio Delta Interface Card" driver will appear in the Add Unlisted or  
Updated Driver dialog box. Click OK.  
7. Windows NT will require you to restart your computer for the changes to take  
effect. Choose "Restart Now." Upon restart, your Delta 1010LT will be ready  
for use.  
Verifying Windows Driver Installation  
Windows displays the Delta 1010LT driver status in the Device Manager page of the  
System Properties dialog box. The Device Manager page is opened via the Windows Start  
button: select Start | Settings | Control Panel | System | Device Manager. With the Device  
Manager displayed, click on the "+" next to "Sound, video and game controllers" to open  
a list of devices, the Delta 1010LT being a device of that nature. Below is an example view  
of the Device Manager.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This example shows the M-Audio Delta 1010LT entry in the Windows Device Manager device  
list. The Delta 1010LT is properly installed with no conflicts. If you do not see your M-Audio  
Delta 1010LT in your Device Manager in this fashion, please jump ahead to the  
"Troubleshooting" section of this manual located on pg 56.  
Verifying Delta Control Panel Software  
Installation in Windows  
In Windows, open the Windows Control Panel (do so via Start | Settings | Control Panel).  
If your Delta 1010LT hardware and Delta Control Panel software are properly installed, the  
Windows Control Panel should display an "M Audio Delta H/W" icon. By double-clicking  
on that icon, you can launch the Delta Control Panel software. For convenience, you may  
also create a shortcut on your desktop by dragging a copy of the "M Audio Delta H/W"  
icon from the Control Panel to your Windows desktop using your mouse or trackball. After  
completing the drag operation, a dialog box will ask you if you wish to create a shortcut --  
click on ‘Yes.’ Once the shortcut is installed, all you have to do is double-click on the  
shortcut icon on your desktop to launch the Delta Control Panel software.  
NOTE: When using a music software program that is ASIO capable,  
launch the Delta Control Panel software from within that program.  
Some of the control panel functions will be controlled from within  
that program, such as master clock setting and sample rate, so it  
is desirable to launch the music program first, and then the Delta  
Control Panel from the the program’s “launch” or “control panel”  
button. Without the music program open however, it is okay to  
open the Delta panel from your desktop or other location.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Delta Driver Software Installation on the Mac  
1. Open the System folder on your Macintosh hard drive. In the System folder,  
locate the Extensions folder.  
2. On you Drivers CD disk, open the Mac Delta Drivers folder. Place the  
extension file "Delta 1010LT Driver" in your Extensions folder by clicking on it  
and dragging it to the Extensions folder.  
3. If you are using a music program that uses ASIO drivers, it will also have an  
ASIO folder within the application’s folder. In your Mac Delta Drivers folder  
you will find three Delta 1010LT ASIO drivers. For Cubase versions 4.x, use the  
"ASIO2 Delta1010LT" driver. For Metro, or earlier versions of Cubase, use the  
"ASIO Delta1010LTv3" driver. For any music program that is not ASIO2 capable,  
use the “ASIO Delta 1010LT” driver instead (check your program’s  
documentation). Place the file "ASIO Delta" in your program's ASIO folder by  
clicking on it and dragging it to the ASIO folder.  
3. Drag the "DeltaPanel PPC" file onto your Macintosh hard drive. You can run the  
Delta Control Panel from any place that's convenient, though music software  
applications that use ASIO will allow you to launch the Delta panel from within the  
program. If not, we suggest creating an alias to the control panel by highlighting it  
and pressing Command (Apple key)+M. Then, drag the alias to the desktop.  
4. With the Delta 1010LT PCI card installed, restarting the computer will load the  
Delta 1010LT extension. You will be able to visually see the Delta extension  
icon pass by as your system loads extension.  
5. Go to theApple menu |Control Panel | Sound. You should see the “built-in” sound  
icon, plus the Delta icon if your Delta 1010LT is properly installed. If your music  
program does use ASIO, you may want to leave the Sound Manager driver set to  
"built-in" for both Sound In and Sound Out. If your program does not use ASIO  
(check your software’s documentation) and you will be using the Sound Manager  
to communicate with your Delta 1010LT, set Sound In and Sound Out to “Delta.”  
See the section “Hardware Settings Page” in the Delta 1010LT “Control Panel  
Software” section for information on selecting Sound Manger inputs and outputs.  
Your Delta 1010LT is now ready for audio input and output. To configure the Delta for MIDI,  
you will need to have Opcode’s OMS (Open Music System) installed first. OMS is provided on  
the CD that came with the unit. Opening the OMS 2.3.7 folder and double-clicking on the “Install  
OMS 2.3.7” program will install OMS in your system. To install the Delta MIDI driver once  
OMS is properly installed:  
1. Open the “Delta Products”folder on the driver CD, then the Delta 1010LT Mac  
folder. Locate the “Delta OMS Driver.”  
2. On your Macintosh hard drive, in your System folder, you will find an “OMS  
Folder.”Drag the Delta OMS Driver into the OMS Folder.  
3. Restart your computer.  
To Configure your Delta 1010LT MIDI in OMS, go to the Control Panel or Chooser under  
the Apple Menu, and make sure AppleTalk is turned off (this is recommended, although  
OMS will sense that it is on and prompt you to turn it off). If you are configuring OMS  
for the first time, follow these instructions to configure OMS.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. In the Opcode folder, which you will find on your hard drive, locate the OMS  
Applications folder, "then OMS Setup." Double click on OMS Setup.  
2. OMS will inform you that it has not yet been configured. Click OK.  
3. The Create A New Studio Setup dialog box now appears. Click OK.  
4. The "OMS Driver Search" box asks you to choose the port on which you've  
attached the Delta MIDI (either Modem or Printer). DO NOT choose a port,  
just click "Search." OMS begins Searching.  
5. "OMS Driver Setup" shows the "Delta" MIDI in a list when OMS successfully  
finds the driver. Click OK. OMS will now define (shows "Identifying") the  
Delta output port. The "OMS MIDI Device Setup" dialog box will appear  
showing the Delta's output port with a check box to the left of the port,  
indicating that the port is enabled. Now click on OK.  
6. Next, the "My Studio Setup" appears with a 'file save' dialog box over it. You  
will now need to save your new Studio Setup before you can assign an  
instrument to the Delta's MIDI output and input. Assign your instrument and  
you are done. You may now exit OMS Setup by quitting the application.  
Delta Control Panel Installation on the Mac  
The Delta Control Panel may be placed anywhere on your hard drive, or any partition of  
your hard drive that you find convenient. Once the control panel file has been dragged  
from the CD onto your hard drive, you may double click it to launch the Delta Control  
Panel software. You may also create an alias to the control panel by highlighting it, then  
holding Apple key+M. This alias can then be placed on your desktop.  
NOTE: When using a music software program that is ASIO capable,  
launch the Delta Control Panel software from within that program.  
Some of the control panel functions will be controlled from within  
that program, such as master clock setting and sample rate, so it  
is desirable to launch the music program first, and then the Delta  
Control Panel from the the program’s “launch” or “control panel”  
button. Without the music program open however, it is okay to  
open the Delta panel from your desktop or other location.  
Delta System Basics  
Delta’s Analog Inputs/Outputs  
The Delta 1010LT PCI Audio Card’s analog inputs and outputs are compatible with a wide  
variety of audio products. The Delta Control Panel software allows you to configure the  
signal level of each analog output individually, or all analog outputs as a group. Signal  
level settings of +4dBu, “Consumer” (-4dBu), and “-10” are available.  
+4dBu is considered a professional operating line level, and is generally associated with  
balanced, two-conductor cables and connectors such as the 1010LT’s analog inputs 1 & 2.  
The +4dBu setting will allow you to accept or output a “hotter” signal. The ‘Consumer’  
setting is preferred for semi-pro audio equipment and some consumer equipment that can  
output accept a ‘hotter’ signal than the ‘-10’ setting. The ‘Consumer’ setting offers  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
approximately 6dB more headroom than does the ‘-10’ setting. Semi-pro and consumer  
device signal levels vary from manufacturer-to-manufacturer and even product-to-  
product, so a little experimentation between Consumer and –10 settings may be required  
for optimal results.  
NOTE: Analog inputs 3 through 8 on the Delta 1010LT do not have  
microphone pre-amplifiers built into them. Therefore direct  
connection to a microphone is not recommended. Instead run the  
microphone signal through a microphone pre-amp (such as the  
M-Audio "Audio Buddy™" or M-Audio “DMP2™”) and then connect  
the pre-amp output to the input of the Delta 1010LT.  
Inputs 1 & 2 are female XLR connectors, and allow connection to balanced microphone  
or line level audio signals. All other analog jacks on the Delta 1010LT breakout cable are  
of the RCA (coaxial) variety. The RCA jacks allow connection to unbalanced (typically  
semi-pro or consumer) connections.  
The Digital Monitor Mixer  
The Delta 1010LT PCI Audio Card has a hardware digital audio mixer built into its PCI  
controller chip. It accepts digital audio streams from all hardware inputs and all outgoing  
software audio devices, mixes them with 36-bit internal precision and then provides the  
mixed output to one or more locations. For the purpose of monitoring, the output of the  
mixer may be routed, via the control panel’s Patchbay/Router page, to the first set of  
Delta 1010LT analog outputs (OUT1/OUT2 as a stereo pair) and/or the S/PDIF digital  
output. At the same time, the mixer may be used for stereo mix-down, with the mixer’s  
output recorded into the user’s application software. The digital audio mixer is configured  
and controlled by the included Delta Control Panel Software.  
The Patchbay / Router  
In addition to the built-in monitor mixer, the Delta 1010LT PCI Audio Card includes an  
output patchbay/router. The patchbay/router allows each output (analog or digital) to be  
connected to a variety of input sources. The 1010LT’s outputs may accept audio from  
software sources (these output devices are visible in your audio software applications) or  
from hardware sources such as the analog and digital inputs or the monitor mixer. This  
capability makes the Delta 1010LT quite flexible for playing and monitoring any audio  
file format, or directly connecting inputs to outputs for system test purposes.  
Synchronization  
For proper operation, the entire Delta 1010LT system is always synchronized to a single  
master clock. The master clock is chosen via the Delta Control Panel software and this  
clock may be derived from the Delta 1010LT’s internal crystal oscillators, S/PDIF In, or  
Word Clock In. Most of the time the master clock is taken from the internal crystal  
oscillators. However, the S/PDIF and Word Clock options are used in situations where  
the Delta 1010LT must be synchronized to external digital audio or sample rates derived  
from an external device.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the initial default setting, the master clock is derived from the internal crystal  
oscillators. Operation in this mode is similar to that of a generic sound card – for instance,  
when an audio file is played through the Delta drivers, the software application playing  
the audio file is responsible for setting the sample rate in the sound card hardware. The  
Delta 1010LT supports these sample rates by using either of its internal crystal oscillators  
and dividing the rate of that oscillator by some value to derive the proper sample rate.  
In situations where S/PDIF In is being used, the Delta 1010LT should usually be configured  
to get its master clock from the S/PDIF In data stream. The reason for this is simple – an  
S/PDIF data stream coming from an external source is rarely going to be in sync with the  
Delta 1010LT (or other digital audio devices in the system for that matter), even if the  
sample rates are set the same. If the master clock were set to use the internal crystal, then  
the incoming S/PDIF audio would have "pops," "crackles," and other undesirable audio  
artifacts present in it. Instead, setting the master clock to "S/PDIF In" will synchronize the  
Delta 1010LT to the S/PDIF input data and its digital audio will be transferred properly.  
There is one special case to consider, however. The external unit sending the S/PDIF digital  
audio to the Delta 1010LT may be "locked" to the word clock emitted from the Delta 1010,  
or both the external unit and the Delta 1010LT are locked to the same external word clock.  
In these cases, the Delta 1010LT and the external S/PDIF device are in-sync, and the  
S/PDIF data would therefore be in-sync with the Delta 1010LT system.  
We’ve discussed internal crystals and S/PDIF In as master clock sources. The third option  
is Word Clock. Word Clock is the desirable choice when you want to synchronize the  
Delta 1010LT with the word clock of something else in your system. That "something  
else" may be a another unit that has a word clock output, or it may be a dedicated house  
word clock generator.  
Finally, the Word Clock and S/PDIF In options may be used to operate the Delta 1010LT  
at non-standard sample rates. When one of these two options is selected, the  
Delta 1010LT’s sample rate will automatically match that of the incoming word clock or  
S/PDIF data stream.  
NOTE: When either the S/PDIF In or Word Clock is selected  
as the master clock source, the Delta 1010LT mixer’s  
frequency response will be affected by whatever sample  
rates you inject at the S/PDIF In or Word Clock In. This is  
because (1) the digital mixer operates at the same sample  
rate as the rest of the board, and (2) sample rate and  
frequency response are directly correlated.  
Using the Delta 1010LT with your Music  
Software Application  
Once the Delta 1010LT’s hardware and driver software are properly installed, it is ready for  
use with your music application software. Some of these applications may require you to  
highlight or enable the Delta 1010LT drivers within the program, and others may have a  
utility that analyzes or profiles the audio cards in your system and enables the drivers. Your  
software should have an audio device driver setup page.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WINDOWS MME AUDIO INPUT DEVICES: All Delta 1010LT analog and S/PDIF  
inputs may be used simultaneously for a total of 10 input channels. Within your software  
application(s), the names of the Delta 1010LT audio input devices are:  
PCM In 1/2 Delta-1010LT  
PCM In 3/4 Delta-1010LT  
PCM In 5/6 Delta-1010LT  
PCM In 7/8 Delta-1010LT  
S/PDIF In Delta-1010LT  
Mon. Mixer Delta-1010LT  
The PCM In devices allow recording a stereo stream directly from the specified analog  
input pairs. The S/PDIF In device allows you to record a stereo stream directly from the  
S/PDIF input. The Mon. Mixer device allows stereo recording from the digital "monitor"  
mixer built-into the Delta 1010LT. The audio data recorded from this device is the mix of  
input and output streams that is set up in the Delta Control Panel software’s Monitor  
Mixer page (see Delta 1010LT Control Panel Software section).  
Note that all of the input devices are stereo. Your application software may break these down  
further to "left" and "right" mono devices. Therefore you may see them as "Left PCM In 1/2  
Delta-1010LT, Right PCM In 1/2 Delta-1010LT," "Left S/PDIF In Delta-1010LT, Right S/PDIF  
In Delta-1010LT," or "Left Mon. Mixer Delta-1010LT, Right Mon. Mixer Delta-1010LT," etc.  
from within your recording software.  
WINDOWS MME AUDIO OUTPUT DEVICES: All Delta 1010LT analog and S/PDIF  
outputs may be used simultaneously for a total of 10 output channels. Within your  
software application(s), the names of the Delta 1010LT audio output devices are:  
WavOut 1/2 Delta-1010LT  
WavOut 3/4 Delta-1010LT  
WavOut 5/6 Delta-1010LT  
WavOut 7/8 Delta-1010LT  
WavOut S/PDIF Delta-1010LT  
All WavOut devices allow playing a stereo audio stream to the analog hardware outputs (for  
WavOut 1/2, 3/4, 5/6, 7/8), the S/PDIF hardware output (for WavOut S/PDIF), and/or into the  
hardware router or mixer. Your application software may break each of these stereo devices  
down further to "left" and "right" mono devices. Therefore you may see them as "Left  
WavOut 1/2 Delta-1010LT, Right WavOut 1/2 Delta-1010LT", or "Left WavOut S/PDIF  
Delta-1010LT, Right WavOut S/PDIF Delta-1010LT", etc. from within your music software.  
Other software will handle the outputs as stereo pairs, but allow you to pan audio left or right  
within the pair.  
Note that each device name begins with "WavOut." This is to remind you that these are  
software devices, and not always connected directly to output hardware. Instead they are  
connected to the Delta 1010LT’s internal patchbay/router and may be sent to one of many  
destinations. For more on the patchbay/router, see the Patchbay/Router section of the  
Delta Control Panel software discussion.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASIO or EASI DRIVER INPUT DEVICES: When using the ASIO or the EASI audio  
drivers with music programs that support this type of audio, the input devices are  
displayed as mono devices. Within these software applications, the names of the  
Delta 1010LT audio input devices are:  
Analog In1 Delta-1010LT  
Analog In2 Delta-1010LT  
Analog In3 Delta-1010LT  
Analog In4 Delta-1010LT  
Analog In5 Delta-1010LT  
Analog In6 Delta-1010LT  
Analog In7 Delta-1010LT  
Analog In8 Delta-1010LT  
S/PDIF In L Delta-1010LT  
S/PDIF In R Delta-1010LT  
Mon. Mixer L Delta-1010LT  
Mon. Mixer R Delta-1010LT  
Notice the S/PDIF In and Monitor Mixer names include "L" and "R" characters. "L" indicates  
the left channel of the stereo stream, while "R" indicates right channel.  
ASIO or EASI DRIVER OUTPUT DEVICES: The Delta 1010LT’s ASIO and EASI  
output devices appear in stereo pairs. Because each device is stereo, you may see "left"  
and "right" references within your software application. This allows the application to pan  
audio left and right under software control. To send a signal to a Delta ASIO output 1 (for  
example) as a mono output send, one would choose "Analog 1/2 Delta-1010LT" for that  
track’s output port, and then pan that output hard left. These outputs are named as follows:  
Analog 1/2 Delta-1010LT  
Analog 3/4 Delta-1010LT  
Analog 5/6 Delta-1010LT  
Analog 7/8 Delta-1010LT  
S/PDIF L/R Delta-1010LT  
MIDI DRIVERS: The Delta 1010LT MIDI drivers, once enabled in your software’s MIDI  
Setup, will appear as a MIDI source and a MIDI port within that program’s track  
configuration windows. The MIDI input driver is named "MIDI In Delta-1010LT," and the  
MIDI output driver is named "MIDI Out Delta-1010LT." Some software applications allow  
you to redefine/rename these devices per supplied or manually entered instrument definitions.  
WINDOWS MULTIMEDIA SETTINGS: Windows may be set up to use the  
Delta 1010LT as its default audio device, allowing system sounds to be sent out the  
Delta 1010LT. This also enables you to use the Delta 1010LT with the sound applets  
included with Windows. To set this up, go to Control Panel | Multimedia. In the Audio  
Properties page, set the Playback and Recording devices to the Delta 1010LT input and  
output devices of your choice.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Windows may also use the Delta 1010LT as its default MIDI device. This allows the  
Delta 1010LT to be used with the MIDI applications included with Windows. To set this  
up, go to Control Panel | Multimedia | MIDI. Set the Delta MIDI driver as the default  
Windows MIDI driver by clicking on the "MIDI Out Delta-1010LT" entry in the driver  
list, then selecting "OK" or "Apply."  
MACINTOSH SOUND MANAGER INPUTS AND OUTPUTS: The Apple Sound  
Manager limits the user to one stereo pair for input and one stereo pair for output. Within  
your music software, the device selection when using the Sound Manager drivers for input  
and output will be “Sound Manager” both for input source and for output port.  
To select the Sound Manager driver, open the Apple Menu and go to Control Panel |  
Sounds. For both “Sound In” and “Sound Out,” click and highlight the Delta icon, then  
exit. You may select which Delta hardware stereo input pair and stereo output pair will be  
used for the Sound Manager’s Sound In and Sound Out in the Delta Control Panel  
“Hardware Settings Page” (see section, “Hardware Settings Page”under “Delta Control  
Panel”). Whichever stereo pair you select, the software input and output device selection  
within your music program will remain the same, namely, “Sound Manager.”  
Delta 1010LT Control Panel Software - PC  
Once the Delta 1010LT is properly installed, an "M Audio Delta H/W" icon will be  
displayed in your Windows Control Panel. By double-clicking on that icon, you will  
launch the Delta Control Panel software. You may also launch the Delta Control Panel  
software from the desktop if you have previously created a shortcut there (see "Verifying  
Delta Control Panel Software Installation" section for instructions on how to do this).  
Once the Delta Control Panel software has been opened, you will see the main panel and  
its several tabs. To display a desired page, click on its tab. Below are functional  
descriptions of each page.  
NOTE: When using a music software program that is ASIO capable,  
launch the Delta Control Panel software from within that program.  
There will be a button in the ASIO or Audio setup page that will  
allow you to do so. Some of the control panel functions will be  
controlled from within that program, such as master clock setting  
and sample rate, so it is desirable to launch the music program  
first, and then the Delta Control Panel from the the program’s  
“launch” or “control panel” button. Without the music program  
open however, it is okay to open the Delta panel from your desktop  
or other location.  
Monitor Mixer Page  
The Monitor Mixer is the first page that appears when the Delta Control Panel is opened,  
and controls the digital mixer built into the Delta 1010LT’s PCI controller chip. As  
described in previous sections, the output of this mixer may be assigned to the  
OUT1/OUT2 analog outputs and/or the S/PDIF Out digital output (this selection is made  
in the Patchbay Router page). At the same time, the mixer outputs may be recorded in  
stereo by software.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Monitor Mixer Page is essentially a collection of volume level faders, audio level (or  
‘peak’) meters, and solo/mute controls. For each mixer output and input channel there is  
one of each: a volume fader, a peak meter, a solo control, and a mute control.  
LEVEL FADERS: Each volume fader may be controlled by dragging the fader ‘handle’  
vertically with the mouse, or by clicking on the ‘handle’ to make it active and then  
adjusting it with the up/down cursor keys of your computer keyboard. Because the mixer  
has no gain, these faders only attenuate (reduce) the signal levels. The highest setting is  
0dB, or ‘Unity Gain.’ The default fader setting is the quietest setting, –144dB, which  
essentially mutes the audio. A pair of level faders may be "ganged" so that both channels  
may be adjusted together as a stereo pair.  
Also, at the top of each fader and meter is a fader level "fine adjustment" control. Clicking  
on the small "up" and "down" arrows will adjust the corresponding fader setting in 0.5dB  
increments. Next to each fine adjustment control is a numerical fader readout that is always  
current and active.  
PEAK METERS: Each peak meter indicates an audio signal level in "dB relative to  
full-scale." This means that a full-scale signal is referred to as "0 dB" and a signal that is  
12dB "quieter" than full-scale is referred to as "-12dB." The meters are vertically  
color-coded into three sections: green, yellow and red. The green section represents a safe  
zone, ranging from approximately -48dB to -12dB. Most audio signals should  
appropriately fill this section of the meter. The yellow section ranges from -12dB to -3dB  
as the signal approaches a ‘hotter’ level. For best capture resolution, recording in this area  
is both safe and advised. The red section of the meter ranges from -3dB to 0dB. On the  
input level meters, a 0dB condition indicates overload and audio clipping may occur.  
Therefore be careful to adjust the incoming audio levels so that they do not peak in the red  
section too long (you might use the monitoring capability of the Delta 1010LT to let your  
ears be the judge). On all output level meters, 0dB indicates full-scale output. Unlike the  
inputs, clipping is impossible on the outputs because of the 36-bit resolution built into the  
mixer hardware.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MASTER VOLUME: At the left side of the Monitor Mixer page, you will see the ‘Master  
Volume’ faders and peak meters. These faders have the longest ‘throw’ and highest meter  
resolution of any level controls in the mixer page. They control the overall stereo level of  
the mixer output. The peak meters indicate the output signal levels with respect to full-scale  
and are directly affected by the settings of the master volume faders.  
MIXER INPUTS: The ‘Mixer Inputs’ are inputs to the monitor mixer. These inputs accept  
hardware audio streams (directly from the Delta’s analog and digital input ports) and  
software audio streams (digital audio generated in software to be output). This combination  
of streams makes the monitor mixer extremely flexible. Each mixer input channel has its  
own level fader and may be panned anywhere in the left/right stereo field. Each input also  
has its own peak meter. The peak meters indicate the incoming "pre-fader" levels of the  
incoming audio and are therefore not affected by the fader settings. However, the input  
faders do affect the levels of the signals exiting the mixer and you will see the affect of the  
input faders on the output "Master Volume" peak meters.  
Because of the large number of mixer inputs, not all inputs are displayed simultaneously.  
You may use the scroll bar at the bottom of the Delta Control Panel to scroll the view left  
or right. On the PC, from far left to right the inputs are labeled "WavOut 1/2” through  
“WavOut 7/8," then "WavOut S/PDIF." These inputs accept the digital audio streams being  
sent from your software application (or Windows) to the driver devices with those same  
names. Each name begins with "WavOut" to remind you that these are software streams  
and may not necessarily be routed to any physical outputs (see Patchbay/Router Page).  
Further to the right are more channels, labeled "H/W In S/PDIF" and "H/W In 1/2 through  
7/8." These mixer inputs are audio streams from the physical Delta 1010LT hardware  
inputs, hence the "H/W" at the front of each label.  
PAN: Each mixer input may be individually panned anywhere in the stereo output mix. A  
pan control is positioned directly under each input channel peak meter and has the  
appearance of a small vertical pointer. To make a coarse adjustment, click on the pan control  
with your mouse and drag it to the desired position. For finer adjustment (in 1% increments),  
you may click on the pan control to make it active, and then use the left/right or up/down  
cursor keys on your computer keyboard. Either way, while the pan setting is being adjusted,  
its value will appear numerically in the Master Volume’s status box (below the Master  
Volume Stereo Gang control) as a percentage from left pan to right pan: -100% represents  
far left, +100% represents far right, and 0% represents the center.  
SOLO: Each mixer input channel has a "Solo" checkbox associated with it. Clicking on and  
activating a Solo box will solo the selected channel by essentially muting all other signals.  
When more than one channel has Solo selected, all solo channels will be summed to the  
solo ‘buss(path), which is what one might consider an ‘in place’ solo as opposed to a PFL,  
or pre-fader listen (levels and pans still apply). Deactivating all solo boxes will return all  
input channels to their previous mute/unmute states.  
MUTE: Every mixer input channel has a "Mute" checkbox associated with it. Clicking on  
and activating the Mute box will remove that signal from the stereo buss. Deactivating the  
Mute box will add the signal back into the stereo buss.  
STEREO GANG: All input channel pairs have a "Stereo Gang" capability. Clicking on and  
activating the Stereo Gang checkbox will link (or "gang") the left/right faders so that both  
channels may be adjusted together as a stereo pair.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Patchbay/Router Page  
The Patchbay/Router page allows you to connect each of the Delta 1010LT’s hardware  
outputs (4 pairs of analog outputs and 1 pair of digital output channels) to specific audio  
sources within the Delta 1010LT board. To display this page, click the "Patchbay/Router"  
tab of the Delta Control Panel.  
The leftmost vertical column of Patchbay/Router page, "H/W Out 1/2," connects this  
analog stereo pair to one of eight stereo sources:  
1. The default setting, "WavOut 1/2," connects ports OUT1 and OUT2 to your  
music software or Windows multimedia applet. In other words, when music  
software plays audio to the device named "WavOut 1/2 Delta-1010LT" it will  
be routed directly to the "hardware" analog outputs 1 & 2 of your 1010LT  
breakout cable.  
2. The second option, "Monitor Mixer," connects ports OUT1 and OUT2 to the  
outputs of the Delta 1010LT monitor mixer. For more information of the  
capabilities of the monitor mixer, please see the section "Monitor Mixer Page."  
3. The third option, "S/PDIF In," connects ports OUT1 and OUT2 directly to  
the hardware S/PDIF input on the Delta 1010LT PCI host card. The left  
channel of the S/PDIF In is routed to OUT1 and the right channel of the  
S/PDIF In is routed to OUT2.  
4. The fourth option, "S/PDIF In (L/R Rev.)," functions identically to the third  
option, except that the left and right channels are swapped. Therefore in  
this mode, the left channel of the S/PDIF In is routed to OUT2 and the right  
channel of the S/PDIF In is routed to OUT1.  
5. Selections five through eight connect the hardware analog inputs 1 & 2, 3 &  
4, 5 & 6, or 7 & 8 (respectively) directly to the 1010LT’s hardware analog  
outputs 1 & 2. For example, if "H/W In 1/2" were selected, any signal  
present at the IN1 port will be copied to OUT1, and any signal present at the  
IN2 port will be copied to OUT2. This same behavior applies to "H/W In  
3/4," "H/W In 5/6," and "H/W In 7/8" when selected.  
The next three vertical columns of the Patchbay/Router page (from left to right), "H/W  
Out 3/4," "H/W Out 5/6," and "H/W Out 7/8," connect these hardware analog outputs to  
one of four sources. Since the three columns function identically, we’ll use "H/W Out 3/4"  
as the example:  
1. The default setting, "WavOut 3/4," connects ports OUT3 and OUT4 to your  
music software or Windows multimedia applet. In other words, when music  
software plays audio to the device named "WavOut 3/4 Delta-1010LT" it will  
be routed directly to the "hardware" analog outputs 3 & 4 of your 1010LT  
breakout cable.  
2. The second option, "S/PDIF In," connects ports OUT3 and OUT4 directly to  
the hardware S/PDIF input on the Delta 1010LT PCI host card. The left  
channel of the S/PDIF In is routed to OUT3 and the right channel of the  
S/PDIF In is routed to OUT4.  
3. The third option, "S/PDIF In (L/R Rev.)," functions identically to the second  
option, except that the left and right channels are swapped. Therefore in this  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
mode, the left channel of the S/PDIF In is routed to OUT4 and the right  
channel of the S/PDIF In is routed to OUT3.  
4. Options four through seven connect the hardware analog inputs 1 & 2, 3 & 4, 5 &  
6, or 7 & 8 (respectively) directly to the 1010LT’s hardware analog outputs 3 & 4.  
For example, if "H/W In 1/2" were selected, any signal present at the IN1 port  
will be copied to OUT3, and any signal present at the IN2 port will be copied to  
OUT4. This same behavior applies to "H/W In 3/4," "H/W In 5/6," and "H/W  
In 7/8" when selected.  
The rightmost vertical column of Patchbay/Router page, "H/W Out S/PDIF," connects the  
Delta 1010LT’s hardware S/PDIF outputs to one of eight sources:  
1. The default setting, "WavOut S/PDIF," connects the S/PDIF Out port to your  
music software or Windows multimedia applet. In other words, when music  
software plays audio to the device named "WavOut S/PDIF Delta-1010LT" it  
will be routed directly to the hardware S/PDIF output on your Delta 1010LT  
PCI host card.  
2. The second option, "Monitor Mixer," connects the S/PDIF Out port to the  
outputs of the Delta 1010LT monitor mixer. For more information on the  
capabilities of the monitor mixer, please see the section "Monitor Mixer Page."  
3. The third option, "S/PDIF In," connects the S/PDIF Out port directly to the  
hardware S/PDIF input on the Delta 1010LT PCI host card. The left channel  
of the S/PDIF In is routed to the left channel of S/PDIF Out and the right  
channel of the S/PDIF In is routed to the right channel of S/PDIF Out.  
4. The fourth option, "S/PDIF In (L/R Rev.)," functions identically to the third  
option, except that the left and right channels are swapped. Therefore in this  
mode, the left channel of the S/PDIF In is routed to the right channel of  
S/PDIF Out and the right channel of the S/PDIF In is routed to the left  
channel of S/PDIF Out.  
5. Selections five through eight connect the hardware analog inputs 1 & 2, 3 & 4,  
5 & 6, or 7 & 8 (respectively) directly to the 1010LT’s S/PDIF Out port. For  
example, if "H/W In 1/2" were selected, any signal present at the IN1 port will  
be sent to the left channel of the S/PDIF Out, and any signal present at the IN2  
port will be sent to the right channel of the S/PDIF Out. This same behavior  
applies to "H/W In 3/4," "H/W In 5/6," and "H/W In 7/8" when selected.  
At this point, you may begin to realize the versatility of the Monitor Mixer and the  
Patchbay/Router, and the relationship between the two. You may want to re-read this section  
and make some practice adjustments within the Delta Control Panel software to become  
proficient in routing and mixing, as well as check out the Tutorials section toward the end of  
this manual. If somewhere in the process you become confused, you may always restore the  
default settings to use the card as a straight 10-in 10-out device -- just choose the topmost  
option in each of the Patchbay/Router columns.  
Hardware Settings Page  
The Hardware Settings page of the Delta Control Panel gives you control over  
miscellaneous features of the Delta 1010LT. To display this page, click the "Hardware  
Settings" tab of the Delta Control Panel.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MASTER CLOCK: This section allows you to select the source of the board’s master  
clock: Internal Xtal (crystal), S/PDIF In, or Word Clock. Master clock operation is  
outlined in the Synchronization section of this manual. Internal Xtal is the default setting.  
Be sure to select "S/PDIF In" if you will be recording or monitoring an S/PDIF stream, or  
"Word Clock" if you wish to synchronize your digital audio with a source device that is  
Word Clock capable.  
NOTE: If "S/PDIF In" is selected as the master clock source, be  
sure to supply a valid S/PDIF signal to the board’s active S/PDIF  
input. Otherwise, erratic timing and/or improper sample rates will  
be experienced. The same is true for selecting "Word Clock" as the  
master clock setting – make sure there is a valid word clock signal  
present at the Delta 1010’s Word Clock In.  
Once a master clock source has been selected, its synchronization status is continually  
monitored and displayed below the master clock radio buttons. If internal crystal is selected,  
the status display will always say "Locked." On the other hand, if S/PDIF In or Word Clock  
is selected as the master clock source, the control panel will display "Locked" only when a  
valid S/PDIF or Word Clock signal is detected. It will display "Unlocked" when there is no  
signal at the selected input, or when the signal is corrupt or invalid for any reason.  
CODEC SAMPLE RATE: This section indicates the present board sample rate, as set by  
application software. The sample rate selected here will be used to drive the digital mixer  
and all outputs. The "Rate Locked" checkbox is used to force a sample rate upon the  
system. It is disabled by default to allow software access to all supported sample rates.  
When checked, it causes the driver to only operate at the selected sample rate. This means  
that any application that attempts to open the Delta 1010LT driver at a sample rate other  
than the one selected here will fail to do so and will post an error message. "Reset Rate  
When Idle" is selected when you want the sample rate to return to a particular setting  
when a software application is not actively using the board. This is particularly handy for  
keeping the digital mixer running at a specific sample rate.  
NOTE: Because the digital monitor mixer runs at the sample rate of  
the rest of the board, and because sample rate directly affects  
frequency response, it may be desirable to keep the sample rate at  
or above 44.1 kHz while using the monitor mixer. This is  
accomplished by enabling "Reset Rate When Idle" and selecting a  
sample rate of 44.1 kHz or greater.  
S/PDIF SAMPLE RATE: When using S/PDIF In as your master clock, this section tells the  
driver what the expected S/PDIF input sample rate is. The section is only displayed when the  
board is set to use S/PDIF In as the master clock source. From the list, select the sample rate  
closest to that of the S/PDIF input data. The sample rate selected here will be the only sample  
rate available to the software applications. Therefore, you must set your audio software  
application to this same sample rate or else the application will display an error message.  
NOTE: When S/PDIF In is the master clock source, the digital  
monitor mixer will run at the sample rate received at the S/PDIF In.  
Since frequency response and sample rate are directly related, the  
mixer frequency response will be directly related to the sample rate  
of the S/PDIF input data.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WORD CLOCK SAMPLE RATE: When using Word Clock In as your master clock, this  
section tells the driver what the expected word clock input sample rate is. The section is  
only displayed when the board is set to use Word Clock In as the master clock source.  
From the list, select the sample rate closest to that of the incoming word clock. The sample  
rate selected here will be the only sample rate available to the software applications.  
Therefore, you must set your audio software application to this same sample rate or else  
the application will display an error message.  
NOTE: When Word Clock is the master clock source, the digital  
monitor mixer will run at the sample rate received at the Word  
Clock in. Since frequency response and sample rate are directly  
related, the mixer frequency response will be directly related to the  
sample rate of the S/PDIF input data.  
MULTITRACK DRIVER DEVICES: The Delta 1010LT drivers intelligently synchronize the  
beginning of recording and playback across all audio devices on the board. When using  
application software that is capable of using multiple channels simultaneously, select "Single and  
In-Sync" to ensure that all audio channels will begin playback and/or recording at the same time.  
Otherwise select "Independent" to allow the audio channels to play independently – this setting  
may be desirable if more than one application needs to access the Delta 1010LT simultaneously.  
The selection “Multi-card Sync” will remain grayed out until a second Delta PCI card (of which  
there are a variety) is installed in the system. When you wish to synchronize two (or more, up  
to four) Delta cards, select Multi-card Sync on the second and successive cards. Then, select  
S/PDIF as your master clock, and connect the S/PDIF output of the first card to the S/PDIF input  
of the second card, etc. This ensures that when the application goes into record or playback, it  
waits until all audio ports are open before it commences with recording or playback of audio.  
DMA BUFFER SIZES: This section specifies the amount of system memory dedicated to  
digital audio buffering. Setting a buffer size that is too small may result in clicks or pops  
in the audio stream as some data may be lost. Larger buffers cause slightly more latency  
but prevent the pops and clicks that might occur with smaller buffer sizes – the default  
settings are recommended but you may desire to tweak these default settings to suit your  
tastes. This buffer size must be set in the Delta Control Panel before you launch your  
music software. When using ASIO with the Delta 1010LT, set the buffer size in the control  
panel, then exit the control panel. After doing so, launch your music software.  
VARIABLE SIGNAL LEVELS: This section has two layers, providing extremely  
versatile control of your Delta 1010LT’s input and output operating line levels.  
In the first layer there are three selections available for globally setting the operating line  
levels for the Delta 1010LT’s analog input and output ports. These selections are labeled  
“+4dBu,” “Consumer” (-4dB), and “-10dBV,” represented by sets of radio buttons each for  
both the Delta analog inputs and the Delta analog outputs. These sections are labeled “All  
Inputs” and “All Outputs,” respectively.  
The default setting is “Consumer” for both the input and output levels. Consumer is a  
good “middle of the road” setting, and will work well in many situations. The setting you  
choose ultimately should match the line level of the source audio device (for the inputs),  
and the target audio device (for the outputs). Check the user’s guide for these external  
devices for information on their input and/or output line levels.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
At the Delta analog outputs, a +4dBu setting will give the “hottest” output signal level.  
Generally, this signal level is associated with balanced audio inputs. The Delta 1010LT’s  
outputs are unbalanced, but can still interface successfully with balanced inputs. The  
Consumer and -10dBV settings are typically associated with unbalanced operation for both  
consumer and prosumer audio gear, with Consumer being less hot (-4dBV) and -10dBV  
being the least hot. As a rule of thumb, if your signal levels in the computer are sufficient  
but your target device is not receiving enough level, try a hotter output signal level setting.  
At the Delta analog outputs, a +4dBu setting will give the most headroom for recording,  
allowing the Delta 1010LT to accept a hotter signal level. If your source audio device puts  
out less signal, such as unbalanced consumer and prosumer equipment, then the lower  
settings of Consumer and -10dBV will lower the headroom, bringing record ceiling closer  
to the signal that you are recording. As a rule of thumb, the lower the signal level of your  
source audio, the lower the input signal level should be set.  
A unique case here are the Delta 1010LT’s inputs 1&2. While all of the other inputs and  
all of the outputs are unbalanced on RCA connectors (single conductor with a shield),  
inputs 1&2 will accept balanced cables on XLR jacks (two conductor with a shield). You  
may want to set these inputs to a +4dBu signal level setting while setting the rest of the  
inputs to a different line level setting.  
Eight faders are also available for setting each input and output level either individually  
or in stereo pairs. This should be considered an advanced settings page, useful when the  
source audio or target devices are diverse and need custom configuration. To access this  
second layer, click the button labeled “Sliders” located in the lower left-hand corner of the  
Variable Signal Levels section of the Hardware Settings page.  
Initially, the location of the faders will reflect the last radio button selection made in the  
first layer. After a change has been made in the second layer, the first layer will show no  
radio button selection, indicating that a custom setting has been made. The screenshot  
below shows this second layer with the first two faders adjusted to a line level of +4dBu  
for the two balanced inputs on XLR jacks.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
You will notice that the “Input” radio button is selected here, giving us a set of eight faders  
that control input levels. Click the “Output” radio button to access the output faders. Also,  
you can click the “Mono” button to control each fader individually, or the “Stereo” button  
to control faders in stereo pairs.  
At any time, the individual faders may be set to vary the input and output levels of a  
particular port or ports. You can use the +4dBu, Consumer, and -10dBV buttons as a  
starting point, or operate independently of them. The faders can be set incrementally in  
.5dB steps, of which there are 18. If working in surround sound, these faders can be used  
to calibrate speakers for monitoring purposes. If using the 1010LT inputs or outputs for  
other purposes, the faders allow you to address multiple sources and targets individually.  
S/PDIF Page  
The S/PDIF page of the Delta Control Panel configures the S/PDIF output format and  
displays the status of the S/PDIF input. To display this page, click the "S/PDIF" tab of the  
Delta Control Panel software.  
DIGITAL INPUT: This group box displays the current S/PDIF input status. The  
Delta 1010LT’s S/PDIF receiver is capable of recognizing a valid input signal versus an  
invalid, corrupt or non-present one. When a valid signal is detected at S/PDIF In, this  
group box displays "Valid Input Detected." When an invalid signal is detected or no signal  
is present, the group box displays "Invalid or Not Present." Below this message are two  
‘grayed-out’ buttons: "Coax(RCA)" and "Optical." These are functions of the Delta DiO  
2496, another product in the M-Audio Delta line, one with both optical and coaxial  
S/PDIF inputs. These controls do not apply to the Delta 1010LT.  
DIGITALOUTPUT FORMAT: Within the "Digital Output Format" group, you choose the digital audio  
format of the S/PDIF output. The default setting, "Consumer," is a true S/PDIF format and is recognized  
by all consumer devices. The alternate "Professional" setting is an AES/EBU type data stream, but  
electrically S/PDIF. This is a work-around that is recognized by some but not all AES/EBU devices.  
For both consumer and professional output formats, the "Advanced" checkbox will allow you  
to force a few particular status bits in the outgoing S/PDIF signal. The advanced option is for  
expert users only; however, if you decide to go exploring, change a few bit settings and get  
lost, you can always select the "Restore Defaults" button to restore the outgoing status bits to  
their factory settings. When "Consumer" and "Advanced" are both selected, the group  
"Consumer Format Advanced Settings" will appear. When "Professional" and "Advanced" are  
both selected, the group "Professional Format Advanced Settings" will appear. These groups  
are described below:  
CONSUMER FORMAT ADVANCED SETTINGS (Copy Mode): Copy protection, also  
known as Serial Copy Management System (SCMS), is written into the S/PDIF subcode, a  
reserved part of the S/PDIF digital stream that is independent of the actual audio data being  
transmitted. It can be used to inhibit the amount of copies that can be made, or allow for  
unlimited copying. Three SCMS modes are available. "Original (Copy Permitted)" indicates  
that the source material may be copied by a receiving device. "1st Generation" indicates that  
the source material is a first generation copy. Most devices that are capable of recording will  
reject material with this SCMS mode set. The final option is "No SCMS" which may be used  
to override the other two modes and allow a recording device to successfully record the audio  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
data. Different manufacturers’ products may interpret these codes differently and require you  
to set these bits by "trial-and-error" until proper operation is achieved.  
CONSUMER FORMATADVANCED SETTINGS (Emphasis): This status bit is used to indicate  
if pre-emphasis has been applied to the outgoing digital audio signal. The default is "None" and  
rarely will any user want to set the value to "50/15uSec" unless the transmitted audio has been  
encoded with 50/15uSec pre-emphasis.  
PROFESSIONAL FORMATADVANCED SETTINGS (Data Type): The user may assign the  
outgoing data as audio or non-audio data. Many devices ignore this setting. The obvious  
default is "audio," however, choosing “non-audio” is appropriate if you wish to send an AC3  
signal (Dolby Digital 5.1 surround sound) out of the S/PDIF output. Some software DVD  
players are capable of this, as well as AC3 or Dolby Digital encoding software.  
PROFESSIONAL FORMAT ADVANCED SETTINGS (Emphasis): The user may choose to  
indicate or not indicate if pre-emphasis has been applied to the outgoing digital audio signal.  
The default is "None" and rarely will any user want to set the value to "CCITT" or "50/15uSec"  
unless the transmitted audio has been encoded with one of those types of pre-emphasis.  
About Page  
The "About" page, while displaying the handsome M-Audio logo and applicable  
copyright information, also reports the driver version and control panel software version.  
If you have Internet browsing capabilities and are currently connected to the Internet,  
clicking on the Midiman copyright will link you to the M-Audio / Midiman web site.  
Save, Delete, Load Buttons; H/W Installed  
At the rightmost side of the Delta Control Panel are the Save, Load and Delete buttons as  
well as an "installed hardware" set of radio buttons. These controls appear regardless of  
what Delta Control Panel page is being displayed.  
SAVE, DELETE, LOAD: The Delta Control Panel always retains the last settings entered.  
However the Save, Delete, and Load functions expand this capability to store different  
sets of control panel settings using different configuration file names. These  
configurations are then available for recall at a later date and time.  
Clicking the ‘Save’ button brings up a dialog box prompting you to name the current  
configuration. Once you have done this, click ‘OK’, and your current configuration has been  
saved to disk. If you decide that you no longer need a particular configuration, click the  
‘Deletebutton. Highlight the name of the configuration file that you wish to delete, and click  
the ‘OK’ button. To recall or reload a saved configuration, click the ‘Load’ button. Highlight  
the name of the configuration file that you wish to recall, and click ‘OK’. Those settings will  
now appear in the Delta Control Panel and the driver will automatically update the hardware.  
H/W INSTALLED: Up to four Delta cards may be installed in a system at one time. This  
section displays all installed Delta cards, and allows you to select which particular card is  
under the control of the control panel software. To select a card for configuration, click  
the radio button to the left of that particular card in the “H/W Installed” list.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Delta 1010LT Control Panel Software - Mac  
The Delta Control Panel must be placed on the hard drive by dragging the application from  
the Drivers CD. Once this is done, an alias may be created by highlighting the Delta  
Control Panel on the hard drive and pressing the Apple key+M. Then, this alias may be  
dragged to the desktop. Double clicking either will launch the control panel. Once the Delta  
Control Panel software has been opened, you will see the main panel and its several tabs.  
To display a desired page, click on its tab. Below are functional descriptions of each page.  
NOTE: When using a music software program that is ASIO capable,  
launch the Delta Control Panel software from within that program.  
There will be a button in the ASIO or Audio setup page that will  
allow you to do so. Some of the control panel functions will be  
controlled from within that program, such as master clock setting  
and sample rate, so it is desirable to launch the music program  
first, and then the Delta Control Panel from the the program’s  
“launch” or “control panel” button. Without the music program  
open however, it is okay to open the Delta panel from your desktop  
or other location.  
Monitor Mixer Page  
The Monitor Mixer is the first page that appears when the Delta Control Panel is opened,  
and controls the digital mixer built into the Delta 1010LT’s PCI controller chip. As  
described in previous sections, the output of this mixer may be assigned to the  
OUT1/OUT2 analog outputs and/or the S/PDIF Out digital output (this selection is made  
in the Patchbay Router page). At the same time, the mixer outputs may be recorded in  
stereo by software.  
The Monitor Mixer Page is essentially a collection of volume level faders, audio level (or  
‘peak’) meters, and solo/mute controls. For each mixer output and input channel there is one  
of each: a volume fader, a peak meter, a solo control, and a mute control.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LEVEL FADERS: Each volume fader may be controlled by dragging the fader ‘handle’  
vertically with the mouse, or by clicking on the ‘handle’ to make it active and then  
adjusting it with the up/down cursor keys of your computer keyboard. Because the mixer  
has no gain, these faders only attenuate (reduce) the signal levels. The highest setting is  
0dB, or ‘Unity Gain.’ The default fader setting is the quietest setting, –144dB, which  
essentially mutes the audio. A pair of level faders may be "ganged" so that both channels  
may be adjusted together as a stereo pair.  
Also, at the top of each fader and meter is a fader level "fine adjustment" control. Clicking  
on the small "up" and "down" arrows will adjust the corresponding fader setting in 0.5dB  
increments. Next to each fine adjustment control is a numerical fader readout that is  
always current and active.  
PEAK METERS: Each peak meter indicates an audio signal level in "dB relative to  
full-scale." This means that a full-scale signal is referred to as "0 dB" and a signal that is 12dB  
"quieter" than full-scale is referred to as "-12dB." The meters are vertically color-coded into  
three sections: green, yellow and red. The green section represents a safe zone, ranging from  
approximately -48dB to -12dB. Most audio signals should appropriately fill this section of  
the meter. The yellow section ranges from -12dB to -3dB as the signal approaches a ‘hotter’  
level. For best capture resolution, recording in this area is both safe and advised. The red  
section of the meter ranges from -3dB to 0dB. On the input level meters, a 0dB condition  
indicates overload and audio clipping may occur. Therefore be careful to adjust the incoming  
audio levels so that they do not peak in the red section too long (you might use the monitoring  
capability of the Delta 1010LT to let your ears be the judge). On all output level meters, 0dB  
indicates full-scale output. Unlike the inputs, clipping is impossible on the outputs because of  
the 36-bit resolution built into the mixer hardware.  
MASTER VOLUME: At the left side of the Monitor Mixer page, you will see the ‘Master  
Volume’ faders and peak meters. These faders have the longest ‘throw’ and highest meter  
resolution of any level controls in the mixer page. They control the overall stereo level of  
the mixer output. The peak meters indicate the output signal levels with respect to  
full-scale and are directly affected by the settings of the master volume faders.  
MIXER INPUTS: The ‘Mixer Inputs’ are inputs to the monitor mixer. These inputs accept  
hardware audio streams (directly from the Delta’s analog and digital input ports) and  
software audio streams (digital audio generated in software to be output). This  
combination of streams makes the monitor mixer extremely flexible. Each mixer input  
channel has its own level fader and may be panned anywhere in the left/right stereo field.  
Each input also has its own peak meter. The peak meters indicate the incoming "pre-fader"  
levels of the incoming audio and are therefore not affected by the fader settings.  
However, the input faders do affect the levels of the signals exiting the mixer and you will  
see the affect of the input faders on the output "Master Volume" peak meters.  
Because of the large number of mixer inputs, not all inputs are displayed simultaneously.  
You may use the scroll bar at the bottom of the Delta Control Panel to scroll the view left or  
right. From far left to right the inputs are labeled "SM/ASIO 1/2” through “ SM/ASIO 7/8,"  
then "SM/ASIO S/PDIF." These inputs accept the digital audio streams being sent from your  
software application (or the Sound Manager) to those driver devices. Each name begins with  
"SM/ASIO" to remind you that these are software streams and may not necessarily be routed  
to any physical outputs, and need to be connected (see Patchbay/Router Page).  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Further to the right are more channels, labeled "H/W In S/PDIF" and "H/W In 1/2." These  
mixer inputs are audio streams from the physical Delta 1010LT hardware inputs, hence  
the "H/W" at the front of each label.  
PAN: Each mixer input may be individually panned anywhere in the stereo output mix. A  
pan control is positioned directly under each input channel peak meter and has the  
appearance of a small vertical pointer. To make a coarse adjustment, click on the pan  
control with your mouse and drag it to the desired position. For finer adjustment (in 1%  
increments), you may click on the pan control to make it active, and then use the left/right  
or up/down cursor keys on your computer keyboard. Either way, while the pan setting is  
being adjusted, its value will appear numerically in the Master Volume’s status box (below  
the Master Volume Stereo Gang control) as a percentage from left pan to right pan: -100%  
represents far left, +100% represents far right, and 0% represents the center.  
SOLO: Each mixer input channel has a "Solo" checkbox associated with it. Clicking on  
and activating a Solo box will solo the selected channel by essentially muting all other  
signals. When more than one channel has Solo selected, all solo channels will be summed  
to the solo ‘buss’ (path), which is what one might consider an ‘in place’ solo as opposed  
to a PFL, or pre-fader listen (levels and pans still apply). Deactivating all solo boxes will  
return all input channels to their previous mute/unmute states.  
MUTE: Every mixer input channel has a "Mute" checkbox associated with it. Clicking on  
and activating the Mute box will remove that signal from the stereo buss. Deactivating the  
Mute box will add the signal back into the stereo buss.  
STEREO GANG: All input channel pairs have a "Stereo Gang" capability. Clicking on  
and activating the Stereo Gang checkbox will link (or "gang") the left/right faders so that  
both channels may be adjusted together as a stereo pair.  
Patchbay/Router Page  
The Patchbay/Router page allows you to connect each of the Delta 1010LT’s hardware  
outputs (4 pairs of analog outputs and 1 pair of digital output channels) to specific audio  
sources within the Delta 1010LT board. To display this page, click the "Patchbay/Router"  
tab of the Delta Control Panel.  
The leftmost vertical column of Patchbay/Router page, "H/W Out 1/2," connects this  
analog stereo pair to one of eight stereo sources:  
1. The default setting, "SM/ASIO 1/2," connects ports OUT1 and OUT2 to your  
music software or Sound Manager applet (provided that Out 1/2 is your  
selection for Sound Manager output. See next section, Hardware Settings  
Page”). In other words, when music software plays audio to the device named  
"Sound Manager” or “Analog 1/2 Delta-1010LT," it will be routed directly to  
the "hardware" analog outputs 1 & 2 of your 1010LT breakout cable.  
2. The second option, "Monitor Mixer," connects ports OUT1 and OUT2 to the  
outputs of the Delta 1010LT monitor mixer. For more information of the  
capabilities of the monitor mixer, please see the section "Monitor Mixer Page.”  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. The third option, "S/PDIF In," connects ports OUT1 and OUT2 directly to the  
hardware S/PDIF input on the Delta 1010LT PCI host card. The left channel  
of the S/PDIF In is routed to OUT1 and the right channel of the S/PDIF In is  
routed to OUT2.  
4. The fourth option, "S/PDIF In (L/R Rev.)," functions identically to the third  
option, except that the left and right channels are swapped. Therefore in this  
mode, the left channel of the S/PDIF In is routed to OUT2 and the right  
channel of the S/PDIF In is routed to OUT1.  
5. Selections five through eight connect the hardware analog inputs 1 & 2, 3 & 4, 5  
& 6, or 7 & 8 (respectively) directly to the 1010LT’s hardware analog outputs 1 &  
2. For example, if "H/W In 1/2" were selected, any signal present at the IN1 port  
will be copied to OUT1, and any signal present at the IN2 port will be copied to  
OUT2. This same behavior applies to "H/W In 3/4," "H/W In 5/6," and "H/W  
In 7/8" when selected.  
The next three vertical columns of the Patchbay/Router page (from left to right), "H/W  
Out 3/4," "H/W Out 5/6," and "H/W Out 7/8," connect these hardware analog outputs to  
one of four sources. Since the three columns function identically, we’ll use "H/W Out 3/4"  
as the example:  
1. The default setting, "SM/ASIO 3/4," connects ports OUT3 and OUT4 to your  
music software or Sound Manager applet (provided that Out 3/4 is your  
selection for Sound Manager output. See next section, Hardware Settings  
Page”). In other words, when music software plays audio to the device named  
"Sound Manager” or Analog 3/4 Delta 1010LT" it will be routed directly to the  
"hardware" analog outputs 3 & 4 of your 1010LT breakout cable.  
2. The second option, "S/PDIF In," connects ports OUT3 and OUT4 directly to  
the hardware S/PDIF input on the Delta 1010 PCI host card. The left channel  
of the S/PDIF In is routed to OUT3 and the right channel of the S/PDIF In is  
routed to OUT4.  
3. The third option, "S/PDIF In (L/R Rev.)," functions identically to the second  
option, except that the left and right channels are swapped. Therefore in this  
mode, the left channel of the S/PDIF In is routed to OUT4 and the right  
channel of the S/PDIF In is routed to OUT3.  
4. Options four through seven connect the hardware analog inputs 1 & 2, 3 & 4, 5 &  
6, or 7 & 8 (respectively) directly to the 1010LT’s hardware analog outputs 3 & 4.  
For example, if "H/W In 1/2" were selected, any signal present at the IN1 port  
will be copied to OUT3, and any signal present at the IN2 port will be copied to  
OUT4. This same behavior applies to "H/W In 3/4,” "H/W In 5/6," and "H/W  
In 7/8" when selected.  
The rightmost vertical column of Patchbay/Router page, "H/W Out S/PDIF," connects the  
Delta 1010LT’s hardware S/PDIF outputs to one of eight sources:  
1. The default setting, "SM/ASIO S/PDIF," connects the S/PDIF Out port to  
your music software or Sound Manager applet (provided that S/PDIF is your  
selection for Sound Manager output. See next section, Hardware Settings  
Page”). In other words, when music software plays audio to the device named  
"Sound Manager” or “S/PDIF Delta-1010LT," it will be routed directly to the  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
hardware S/PDIF output on your Delta 1010LT PCI host card.  
2. The second option, "Monitor Mixer," connects the S/PDIF Out port to the  
outputs of the Delta 1010LT monitor mixer. For more information on the  
capabilities of the monitor mixer, please see the section "Monitor Mixer Page.”  
3. The third option, "S/PDIF In," connects the S/PDIF Out port directly to the  
hardware S/PDIF input on the Delta 1010LT PCI host card. The left channel  
of the S/PDIF In is routed to the left channel of S/PDIF Out and the right  
channel of the S/PDIF In is routed to the right channel of S/PDIF Out.  
4. The fourth option, "S/PDIF In (L/R Rev.)," functions identically to the third  
option, except that the left and right channels are swapped. Therefore in this  
mode, the left channel of the S/PDIF In is routed to the right channel of  
S/PDIF Out and the right channel of the S/PDIF In is routed to the left  
channel of S/PDIF Out.  
5. Selections five through eight connect the hardware analog inputs 1 & 2, 3 & 4,  
5 & 6, or 7 & 8 (respectively) directly to the 1010LT’s S/PDIF Out port. For  
example, if "H/W In 1/2" were selected, any signal present at the IN1 port  
will be sent to the left channel of the S/PDIF Out, and any signal present at  
the IN2 port will be sent to the right channel of the S/PDIF Out. This same  
behavior applies to "H/W In 3/4," "H/W In 5/6," and "H/W In 7/8" when  
selected.  
At this point, you may begin to realize the versatility of the Monitor Mixer and the  
Patchbay/Router, and the relationship between the two. You may want to re-read this  
section and make some practice adjustments within the Delta Control Panel software to  
become proficient in routing and mixing, as well as check out the Tutorials section toward  
the end of this manual. If somewhere in the process you become confused, you may  
always restore the default settings to use the card as a straight 4-in 10-out device -- just  
choose the topmost option in each of the Patchbay/Router columns.  
Hardware Settings Page  
The Hardware Settings page of the Delta Control Panel gives you control over  
miscellaneous features of the Delta 1010LT. To display this page, click the "Hardware  
Settings" tab of the Delta Control Panel. MASTER CLOCK: This section allows you to  
select the source of the board’s master clock: Internal Xtal (crystal), S/PDIF In, or Word  
Clock. Master clock operation is outlined in the Synchronization section of this manual.  
Internal Xtal is the default setting. Be sure to select "S/PDIF In" if you will be recording  
or monitoring an S/PDIF stream, or "Word Clock" if you wish to synchronize your digital  
audio with a source device that is Word Clock capable.  
NOTE: If "S/PDIF In" is selected as the master clock source, be  
sure to supply a valid S/PDIF signal to the board’s active S/PDIF  
input. Otherwise, erratic timing and/or improper sample rates will  
be experienced. The same is true for selecting "Word Clock" as the  
master clock setting – make sure there is a valid word clock signal  
present at the Delta 1010’s Word Clock In.  
Once a master clock source has been selected, its synchronization status is continually  
monitored and displayed below the master clock radio buttons. If internal crystal is  
selected, the status display will always say "Locked." On the other hand, if S/PDIF In or  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Word Clock is selected as the master clock source, the control panel will display "Locked"  
only when a valid S/PDIF or Word Clock signal is detected. It will display "Unlocked"  
when there is no signal at the selected input, or when the signal is corrupt or invalid for  
any reason.  
CODEC SAMPLE RATE: This section indicates the present board sample rate, as set by  
application software. The sample rate selected here will be used to drive the digital mixer  
and all outputs. The "Rate Locked" checkbox is used to force a sample rate upon the  
system. It is disabled by default to allow software access to all supported sample rates.  
When checked, it causes the driver to only operate at the selected sample rate. This means  
that any application that attempts to open the Delta 1010LT driver at a sample rate other  
than the one selected here will fail to do so and will post an error message. "Reset Rate  
When Idle" is selected when you want the sample rate to return to a particular setting  
when a software application is not actively using the board. This is particularly handy for  
keeping the digital mixer running at a specific sample rate.  
NOTE: Because the digital monitor mixer runs at the sample rate of  
the rest of the board, and because sample rate directly affects  
frequency response, it may be desirable to keep the sample rate at  
or above 44.1 kHz while using the monitor mixer. This is  
accomplished by enabling "Reset Rate When Idle" and selecting a  
sample rate of 44.1 kHz or greater.  
S/PDIF SAMPLE RATE: When using S/PDIF In as your master clock, this section tells the  
driver what the expected S/PDIF input sample rate is. The section is only displayed when the  
board is set to use S/PDIF In as the master clock source. From the list, select the sample rate  
closest to that of the S/PDIF input data. The sample rate selected here will be the only sample  
rate available to the software applications. Therefore, you must set your audio software  
application to this same sample rate or else the application will display an error message.  
NOTE: When S/PDIF In is the master clock source, the digital  
monitor mixer will run at the sample rate received at the S/PDIF In.  
Since frequency response and sample rate are directly related, the  
mixer frequency response will be directly related to the sample rate  
of the S/PDIF input data.  
WORD CLOCK SAMPLE RATE: When using Word Clock In as your master clock, this  
section tells the driver what the expected word clock input sample rate is. The section is  
only displayed when the board is set to use Word Clock In as the master clock source.  
From the list, select the sample rate closest to that of the incoming word clock. The sample  
rate selected here will be the only sample rate available to the software applications.  
Therefore, you must set your audio software application to this same sample rate or else  
the application will display an error message.  
NOTE: When Word Clock is the master clock source, the digital  
monitor mixer will run at the sample rate received at the Word  
Clock in. Since frequency response and sample rate are directly  
related, the mixer frequency response will be directly related to the  
sample rate of the S/PDIF input data.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MULTITRACK DRIVER DEVICES: The Delta 1010LT drivers intelligently synchronize  
the beginning of recording and playback across all audio devices on the board. When using  
application software that is capable of using multiple channels simultaneously, select "Single  
and In-Sync" to ensure that all audio channels will begin playback and/or recording at the  
same time. Otherwise select "Independent" to allow the audio channels to play independently  
– this setting may be desirable if more than one application needs to access the Delta 1010LT  
simultaneously.  
DMA BUFFER SIZES: This section specifies the amount of system memory dedicated to  
digital audio buffering. Setting a buffer size that is too small may result in clicks or pops  
in the audio stream as some data may be lost. Larger buffers cause slightly more latency  
but prevent the pops and clicks that might occur with smaller buffer sizes – the default  
settings are recommended but you may desire to tweak these default settings to suit your  
tastes. This buffer size must be set in the Delta Control Panel before you launch your  
music software. When using ASIO with the Delta 1010LT, set the buffer size in the control  
panel, then exit the control panel. After doing so, launch your music software.  
SOUND MANAGER: The Hardware Settings Page in the Delta Control Panel also contains  
software switches that allow you to select which Delta input and output stereo pair will be  
used by the Sound Manager, if and when you choose the Delta as the Sound Manager input  
and output device. If you go to the Apple menu | Control Panel |Sounds and highlight the  
Delta icon for Sound In and Sound Out, then your Apple system sounds will be routed to the  
Delta hardware output that you have selected here, and Alert Sounds, if you choose to  
record, will receive their input from the Delta hardware input that you select here.  
You will want to choose the Delta for input and output in the Sounds control panel if your  
music program does not use ASIO and the Delta ASIO drivers. If you are using the ASIO  
drivers (see Mac Software Installation), you may want to leave the Sounds control panel  
selection to “built-in.” With the Sounds control panel set to built-in, these Sound Manager  
settings in the Delta Control Panel will have no effect, and your system sounds will come  
from your internal sound card.  
The Sound Manager driver limits you to using only one of the Delta 1010LT stereo input  
pairs for audio input and only one of the stereo output pairs for output. These do not need  
to be matched pairs- you can use inputs 1&2 for Sound In and S/PDIF for Sound Out, for  
example, or any combination that you choose. The following screen shot shows the  
Hardware Settings page on the Mac with the Sound Manager I/O set to “Analog 1&2” for  
Input and “Analog 1&2” for Output. Once you have made a selection, go to the File menu  
and “Save as Preferences.”  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VARIABLE OUTPUT LEVELS: This section has two layers, providing extremely versatile  
control of your Delta 1010LT’s input and output operating line levels.  
In the first layer there are three selections available for globally setting the operating line  
levels for the Delta 1010LT’s analog input and output ports. These selections are labeled  
“+4dBu,” “Consumer” (-4dB), and “-10dBV,” represented by sets of radio buttons each for  
both the Delta analog inputs and the Delta analog outputs. These sections are labeled “All  
Inputs” and “All Outputs,” respectively.  
The default setting is “Consumer” for both the input and output levels. Consumer is a good  
“middle of the road” setting, and will work well in many situations. The setting you  
choose ultimately should match the line level of the source audio device (for the  
inputs), and the target audio device (for the outputs). Check the user’s guide for  
these external devices for information on their input and/or output line levels.  
At the Delta analog outputs, a +4dBu setting will give the “hottest” output signal  
level. Generally, this signal level is associated with balanced audio inputs. The  
Delta 1010LT’s outputs are unbalanced, but can still interface successfully with  
balanced inputs. The Consumer and -10dBV settings are typically associated with  
unbalanced operation for both consumer and prosumer audio gear, with Consumer  
being less hot (-4dBV) and -10dBV being the least hot. As a rule of thumb, if your  
signal levels in the computer are sufficient but your target device is not receiving  
enough level, try a hotter output signal level setting.  
At the Delta analog inputs, a +4dBu setting will give the most headroom for recording,  
allowing the Delta 1010LT to accept a hotter signal level. If your source audio device  
puts out less signal, such as unbalanced consumer and prosumer equipment, then the  
lower settings of Consumer and -10dBV will lower the headroom, bringing record  
ceiling closer to the signal that you are recording. As a rule of thumb, the lower the  
signal level of your source audio, the lower the input signal level should be set.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A unique case here are the Delta 1010LT’s inputs 1&2. While all of the other inputs  
and all of the outputs are unbalanced on RCA connectors (single conductor with a  
shield), inputs 1&2 will accept balanced cables on XLR jacks (two conductor with a  
shield). You may want to set these inputs to a +4dBu signal level setting while setting  
the rest of the inputs to a different line level setting.  
Eight faders are also available for setting each input and output level either individually or in  
stereo pairs. This should be considered an advanced settings page, useful when the source audio  
or target devices are diverse and need custom configuration. To access this second layer, click  
the button labeled “Sliders” located in the lower left-hand corner of the Variable Signal Levels  
section of the Hardware Settings page.  
Initially, the location of the faders will reflect the last radio button selection made in the first layer.  
After a change has been made in the second layer, the first layer will show no radio button  
selection, indicating that a custom setting has been made.  
You will notice when you access the second layer that the “Input” radio button is selected,  
giving us a set of eight faders that control input levels. Click the “Output” radio button to  
access the output faders. Also, you can click the “Mono” button to control each fader  
individually, or the “Stereo” button to control faders in stereo pairs.  
At any time, the individual faders may be set to vary the input and output levels of a particular  
port or ports. You can use the +4dBu, Consumer, and -10dBV buttons as a starting point, or  
operate independently of them. The faders can be set incrementally in .5dB steps, of which  
there are 18. If working in surround sound, these faders can be used to calibrate speakers for  
monitoring purposes. If using the 1010LT inputs or outputs for other purposes, the faders allow  
you to address multiple sources and targets individually.  
S/PDIF Page  
The S/PDIF page of the Delta Control Panel configures the S/PDIF output format and  
displays the status of the S/PDIF input. To display this page, click the "S/PDIF" tab of the  
Delta Control Panel software.  
DIGITAL INPUT: This group box displays the current S/PDIF input status. The  
Delta 1010LT’s S/PDIF receiver is capable of recognizing a valid input signal versus an  
invalid, corrupt or non-present one. When a valid signal is detected at S/PDIF In, this group  
box displays "Valid Input Detected." When an invalid signal is detected or no signal is present,  
the group box displays "Invalid or Not Present." Below this message are two ‘grayed-out’  
buttons: "Coax(RCA)" and "Optical." These are functions of the Delta DiO 2496, another  
product in the M-Audio Delta line, one with both optical and coaxial S/PDIF inputs. These  
controls do not apply to the Delta 1010LT.  
DIGITAL OUTPUT FORMAT: Within the "Digital Output Format" group, you choose the  
digital audio format of the S/PDIF output. The default setting, "Consumer," is a true  
S/PDIF format and is recognized by all consumer devices. The alternate "Professional"  
setting is an AES/EBU type data stream, but electrically S/PDIF. This is a work-around  
that is recognized by some but not all AES/EBU devices.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For both consumer and professional output formats, the "Advanced" checkbox will allow  
you to force a few particular status bits in the outgoing S/PDIF signal. The advanced  
option is for expert users only; however, if you decide to go exploring, change a few bit  
settings and get lost, you can always select the "Restore Defaults" button to restore the  
outgoing status bits to their factory settings. When "Consumer" and "Advanced" are both  
selected, the group "Consumer Format Advanced Settings" will appear. When  
"Professional" and "Advanced" are both selected, the group "Professional Format  
Advanced Settings" will appear. These groups are described below:  
CONSUMER FORMAT ADVANCED SETTINGS (Copy Mode): Copy protection, also  
known as Serial Copy Management System (SCMS), is written into the S/PDIF subcode,  
a reserved part of the S/PDIF digital stream that is independent of the actual audio data  
being transmitted. It can be used to inhibit the amount of copies that can be made, or allow  
for unlimited copying. Three SCMS modes are available. "Original (Copy Permitted)"  
indicates that the source material may be copied by a receiving device. "1st Generation"  
indicates that the source material is a first generation copy. Most devices that are capable  
of recording will reject material with this SCMS mode set. The final option is "No SCMS"  
which may be used to override the other two modes and allow a recording device to  
successfully record the audio data. Different manufacturers’ products may interpret these  
codes differently and require you to set these bits by "trial-and-error" until proper  
operation is achieved.  
CONSUMER FORMAT ADVANCED SETTINGS (Emphasis): This status bit is used to  
indicate if pre-emphasis has been applied to the outgoing digital audio signal. The default is  
"None" and rarely will any user want to set the value to "50/15uSec" unless the transmitted  
audio has been encoded with 50/15uSec pre-emphasis.  
PROFESSIONAL FORMAT ADVANCED SETTINGS (Data Type): The user may assign  
the outgoing data as audio or non-audio data. Many devices ignore this setting. The  
obvious default is "audio," however, choosing “non-audio” is appropriate if you wish to  
send an AC3 signal (Dolby Digital 5.1 surround sound) out of the S/PDIF output. Some  
software DVD players are capable of this, as well as AC3 or Dolby Digital encoding  
software.  
PROFESSIONAL FORMAT ADVANCED SETTINGS (Emphasis): The user may choose to  
indicate or not indicate if pre-emphasis has been applied to the outgoing digital audio signal.  
The default is "None" and rarely will any user want to set the value to "CCITT" or "50/15uSec"  
unless the transmitted audio has been encoded with one of those types of pre-emphasis.  
About Page  
The "About" page, while displaying the handsome M-Audio logo and applicable  
copyright information, also reports the driver version and control panel software version.  
Save, Delete, Load Buttons; H/W Installed  
To save your Delta control Panel settings, go to the File menu and select “Save,”or “Save  
as.” A dialog box will appear, prompting you to name the current configuration. Once you  
have done so, click the Save button. To save the current settings as your default, go to the  
File menu and choose “Save as Preferences.”  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
In the upper righthand corner of the control panel is a “H/W Installed” drop-down list. At  
the time of this writing, the Delta Mac ASIO drivers will support only a single Delta device,  
and of course the Sound Manager will support only one stereo pair regardless of how many  
audio cards are installed in your system. The H/W Installed list will display  
“Delta 1010LT” as the active device in the control panel.  
Delta 1010LT Recording Tutorials  
In this section we will explore a few sample setups for recording and playback using the  
Delta 1010LT PCI Audio Card. This is by no means an exhaustive tutorial but its intent is  
to help you understand most of the Delta 1010LT’s feature set. Before beginning, you  
should open your music software and profile the Delta 1010LT, enable its drivers, or  
otherwise setup the software for operation with the Delta 1010LT.  
NOTE: All of these examples refer to the Windows MME driver  
names. If you’re using ASIO drivers (or the Apple Sound Manager),  
you’ll need to substitute the appropriate driver names when  
referring to software inputs or outputs.  
Typical Setup #1  
Let’s assume for this setup that we’re recording two vocals, then overdubbing other vocal  
tracks while listening to the first tracks. The following diagram shows two dynamic  
microphones plugged into the Delta 1010LT’s analog inputs 1 & 2. Different instruments,  
such as MIDI modules or keyboards, may also be connected directly to the  
Delta 1010LT’s inputs.  
Delta 1010LT  
breakout 2  
breakout 1  
MIDI  
S/PDIF  
WORDCLOCK  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: Because improper connections may potentially make very  
loud noises, it’s a good idea to have all monitor levels set low or  
muted while hooking up audio equipment -- you may even choose  
to turn your computer off before making the connections.  
1. Plug the first microphone into the 1010LT’s Analog Input 1 XLR jack. Plug the  
second microphone into the Analog Input 2 XLR jack.  
2. Plug the hardware outputs 1 & 2 of the Delta 1010LT, that is the RCA output  
jacks 1 and 2, to a sound system or power amp with speakers.  
4. Turn on your equipment in this suggested order: pre-amp, computer, then  
sound system.  
We’re now physically set up to monitor, record, and play back audio. The next steps  
involve configuring the Delta Control Panel software and the music software into which  
you will be recording. We’ll start with the Delta Control Panel’s "Hardware Settings"  
page, then the "Patchbay/Router" page, and finally the "Monitor Mixer" page. We’re not  
using S/PDIF in this example so we’ll ignore the S/PDIF page.  
5. Open the Delta Control Panel by double clicking the icon in your Windows  
Control Panel, and then click on the ‘Hardware Settings’ tab.  
6. Select ‘Internal Xtal’ as the master clock source. This allows the Delta 1010LT  
to derive its sample rates from its internal clock oscillator. ‘Internal Xtal’ is the  
default setting for the Delta Control Panel, so selecting it may not be necessary  
(it may already be selected).  
7. Under "CODEC Sample Rate," verify that the "Rate Locked" checkbox is not  
activated. This will allow your application software to set the Delta 1010LT  
sample rate as it pleases.  
8. Since this example will include the use of the monitor mixer, we will activate  
the "Reset Rate When Idle" feature. This will make sure the monitor mixer is  
running at a decent sample rate while the system is idle – this prevents the  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
mixer sample rate from being set too low and therefore lowering its frequency  
response. Select a sample rate in the "CODEC Sample Rate" group to use as  
this idle sample rate. Choose a 44.1kHz or higher setting for best results, and  
select the same sample rate you will be using in your application if possible.  
We’ve chosen 48,000kHz for this example.  
Now click on the Delta Control Panel’s "Patchbay/Router" tab. In the first column of the  
Patchbay/Router page, click the radio button "Monitor Mixer" to connect the monitor  
mixer’s stereo output directly to Delta analog outputs OUT1 and OUT2. Now, everything  
that we hear at outputs 1 & 2 will reflect our settings in the Monitor Mixer page.  
Select the "Monitor Mixer" tab of the Delta Control Panel. The default Master Volume  
fader settings are 0dB and unmuted, and all other faders are set to full attenuation  
(-144dB) and muted. We will need to adjust these to our preference. The screen capture  
on the next page shows the settings that we wish to achieve.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. In the Mixer Input column labeled "WavOut 1/2," click on each fader handle  
and drag it up to the 0dB setting. Also, deactivate (uncheck) each WavOut 1/2  
mute box to unmute the channels. This will allow us, once we’ve recorded  
into a music software program, to hear those software outputs upon playback.  
10. Using the scroll bar at the bottom of the control panel, scroll to the right until  
you see the column labeled "H/W In 1/2." Test mic #1, and you should see an  
indication in the left meter, which represents signal levels from the Delta  
analog input 1. Test mic #2, and you should see an indication in the right  
meter, which represents signal levels from Delta hardware input 2.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. You want to be seeing a good level on the input meters, about –6dB to –3dB in  
the loudest parts (this is playing it a safe because you don’t want to hit 0dB  
and “clip” the signal). These are the levels at which the signals will be  
recorded. If your signal is too hot, i.e, clipping in the red, then go into the  
Variable Signal Level section of the Delta control Panel’s “Hardware Settings”  
page and raise the input line level setting to a higher setting. If your signal  
doesn’t seem hot enough, lower the input line level setting to a lower setting,  
i.e. Consumer or -10.  
12. Now let’s set the levels at which you will monitor both microphones while  
recording. These are not to be confused with the levels that are recorded by  
the software – these levels are merely monitor levels that appear in the mixer  
outputs (in this case at Delta 1010LT analog outs 1 & 2). Click on the left fader  
handle of H/W In 1/2, and drag it about halfway up. Test mic #1. If it’s not  
loud enough, bring it up all of the way. If it is still not loud enough, you will  
have to raise the listening level of your sound system. Make similar  
adjustments for microphone #2, using the right fader. You may want to set the  
pan position to suit your needs.  
13. Now fine-tune your monitor levels. Sing and otherwise test the microphones,  
adjusting your listening levels using the H/W In 1/2 faders so that you have  
a comfortable blend of mic levels.  
Now is the time to launch your music software and set it up to record and playback audio  
tracks. We’re going to speak in general terms here, since setup within software programs  
will vary somewhat. Minimize your Delta Control Panel so that you can easily access it  
from your Windows taskbar. Then open your music software program.  
14. First set up the sample rate in the software application. This operation will depend  
on the software. Choose a sample rate that is high enough to capture the  
frequency response of the vocals. A general rule of thumb is to multiply the  
highest frequency you would like to capture by two and add maybe a little on top  
of that – that gives you a suitable sample rate. Also keep in mind that if the final  
results of your work will end up on a CD-ROM burned from your audio file, you  
probably want to use 44.1kHz, the native sample rate of "redbook" CD audio.  
15. In your software application, set the ‘source’ or ‘input port’ to "Left PCM In  
1/2 Delta-1010LT" on track one, and "Right PCM In 1/2 Delta-1010LT" on  
track two. Arm the tracks for recording. Track one is now set up to record  
microphone #1, and track two microphone#2. If your software requires this,  
set the software’s clock source to ‘Audio.’  
16. Press record on your software’s transport bar. Record a take of your Vocals.  
Understand that while recording, you are monitoring the Delta inputs by way  
of the Monitor Mixer settings for H/W In 1/2, and according to the selection of  
‘Monitor Mixer’ within the Patchbay/Router page. At the same time, your  
software is recording from H/W In 1/2.  
17. When you are done playing, stop the recording software and rewind the take.  
Before playing back what you’ve recorded, you will need to assign the  
recorded tracks to output devices on the Delta 1010LT.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note: For efficiency’s sake, this step could have taken place while  
you were setting up the recording track assignments. However,  
since this step only affects playback and does not affect the  
recording setup in any way, we’ve placed it here to lessen  
confusion. This setting only needs to be made once, but may be  
changed if necessary.  
Assign software track 1 to output device "WavOut 1/2 Delta-1010LT" and pan  
the track (within your software) all the way to the left (hard left). Then assign  
track 2 to output device "WavOut 1/2 Delta-1010LT" and pan the track all the  
way to the hard right. Now, when you start playback, track one (mic #1) will  
be sent to the Delta software (WavOut) output 1, and track two (mic #2) to  
Delta software output 2 (you may also choose a panning scheme). These two  
software outputs are connected to the inputs of the monitor mixer, therefore  
the recorded vocal track channels will be sent to the monitor mixer, levels will  
be modified by the mixer and the output of the mixer will be heard at analog  
outputs 1 & 2.  
18. Start playback from your software’s transport bar. Open the Delta Control Panel  
and go to the Monitor Mixer page. Observe the meters at "WavOut 1/2" – these  
are the playback levels of your recorded vocal tracks. Adjust the faders and  
mute controls so that you may hear the vocal tracks at the appropriate levels and  
mix. These are the levels at which you may monitor the pre-recorded tracks while  
you overdub (record other tracks while listening to the first) additional parts.  
Let’s assume that you like this take, and wish to overdub an additional harmony vocals. We  
can still use hardware inputs 1 & 2 of the Delta. We’re set up to do so and there’s no reason  
to change these inputs. Let’s set ourselves up to overdub these next two tracks. We will  
record the next two tracks of material to tracks 3 & 4 of the software:  
19. Back in your music program, set the ‘source’ or ‘input port’ to "Left PCM In 1/2  
Delta-1010LT" on track three, and "Right PCM In 1/2 Delta-1010LT" on track four.  
Arm the tracks for recording. Track three is now set up to record the first  
microphone, and track four the second microphone. Usually at this point you  
would want to return to the Delta Control Panel monitor mixer to set up levels.  
However, because you will be recording the same instruments that you did on the  
first two tracks, you probably won’t need to adjust input or monitoring levels.  
20. Press record on your software’s transport bar. Record a take of your new vocal  
tracks. Because you have set up the first two tracks to play back through the  
monitor mixer, you should hear those original tracks along with the ones that  
you are now recording.  
21. When you are done playing, stop the recording software and rewind the take.  
Before playing back what you’ve recorded, you will need to assign the newly  
recorded tracks to output devices on the Delta 1010LT. In your software, set the  
output ports of tracks three and four to "WavOut 3/4 Delta-1010LT." Now track  
three (first mic) will be sent to the Delta software output 3, and track four  
(second mic) to Delta software output 4.  
22. Press play on your software’s transport bar. Understand now that the four  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
recorded tracks from the software are being sent to WavOut 1, WavOut 2,  
WavOut 3, and WavOut 4 simultaneously. Therefore they are all being input  
to the monitor mixer and their playback levels can be controlled at the  
corresponding channels of the monitor mixer. Open the Monitor Mixer page  
of the Delta Control Panel and adjust the levels of the four channels according  
to your taste. You may also experiment with the Mute and Solo controls while  
listening to the playback. Note also that the mixer continues to monitor the  
microphones at analog inputs 1 & 2.  
At this point, you should be able to see how this multi-tracking session is developing. As  
we add more tracks within our music software, we set them to the next pair of Delta  
software outputs (3/4, then 5/6…), and bring up the faders of those software inputs in the  
monitor mixer (WavOut 3/4, WavOut 5/6…). We continually monitor from the Delta  
hardware outs 1 & 2, via the ‘Mon. Mixer’ setting as the monitor ‘source’ in the  
Patchbay/Router page, and adjusting our mix of the software outputs (and the way we  
monitor our guitar and vocal at the inputs) via the Monitor Mixer settings.  
Notice that if we continue to overdub past track 8, we run out of WavOut devices to assign  
to. In this case, you may want to do some of your level mixing within the software  
application if it supports it. Most applications will allow you to assign more than one track  
to an output device and then set the relative levels of the tracks within the software, letting  
the software do the mixing. In this example you could have assigned all of the playback  
tracks to "WavOut 1/2" and let the software handle the mix.  
Typical Setup #2  
Let’s look at a setup that involves a typical transfer of information from DAT to computer  
and back to DAT. Here, we’ll be using the Delta 1010LT’s S/PDIF I/O, plus one of the  
analog output stereo pairs.  
For this setup, we will connect a DAT to the Delta 1010LT PCI Host card using coaxial  
S/PDIF cables (75-ohm impedance RCA-to-RCA). We’ll also connect the 1010LT’s  
analog outputs to a sound system for monitoring purposes. A setup like this might be used  
to transfer a number of mixes from a DAT into an audio editing program, performing the  
appropriate edits, and then transferring the edited material back to DAT.  
NOTE: Because improper connections can potentially make very  
loud noises, it’s a good idea to have monitor levels down while  
hooking up audio equipment -- you may even choose to turn your  
computer off before making the connections.  
The following examples, at first glance, may look rather long and laborious. However, you  
will find that most of the settings are factory defaults and will rarely need to be modified.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Transferring from DAT to Delta 1010LT  
Delta 1010LT  
S/PDIF IN  
MIDI  
WORDCLOCK  
1. Connect the DAT’s coaxial S/PDIF output to the S/PDIF In of the  
Delta 1010LT PCI host card, using a good quality cable.  
2. Connect the 1010LT analog outputs 1 & 2 to some type of amplified sound  
system. The sound system should be equipped with speakers or head-phones.  
3. Because you will be recording from the S/PDIF input, you will need to set up  
the Delta 1010LT to synchronize its master clock with the S/PDIF input. To do  
this, open the Hardware Settings page of the control panel software. Under  
Master Clock, select "S/PDIF In."  
4. Next, you will need to tell your application software the expected sample rate.  
We’ll use 44.1 kHz in this example. Therefore, on the Hardware Settings page,  
set the "S/PDIF Sample Rate" to 44,100.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. In order to monitor the digital signal coming into the 1010LT, switch to the  
Patchbay/Router page of the control panel software. In the "H/W Out 1/2"  
column, select the radio button named "S/PDIF In." This will copy all S/PDIF  
input audio directly over to the analog outputs – therefore in this example, the  
monitor mixer will be completely bypassed. Once this assignment is made,  
you may play the DAT material at any time and verify that it is making it into  
the Delta 1010LT successfully. This can be done regardless of whether or not  
your recording software is open.  
6. Within your recording software, select "S/PDIF In Delta-1010LT," as the audio  
input device. The Delta input appears as a stereo pair.  
7. Start your software recording and then start your DAT material playing. You  
should be able to hear the DAT material through your sound system.  
Transferring from 1010LT to DAT, monitoring with DAT  
Delta 1010LT  
S/PDIF IN  
MIDI  
WORDCLOCK  
S/PDIF IN  
analog out  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Connect the Delta 1010LT’s S/PDIF Out to the DAT’s coaxial S/PDIF Input using  
a good quality cable.  
2. Connect the DAT analog outputs to some type of amplified sound system. The  
sound system should be equipped with speakers or headphones.  
3. Because you will be playing back at the recorded sample rate, you will want to set  
the Delta 1010LT’s master clock to use the 1010LT internal crystal. Do this by  
opening the Hardware Settings page of the Delta Control Panel software and  
under Master Clock, selecting "Internal Xtal." Also, under the Codec Sample Rate  
section you may uncheck "Rate Locked" if it is previously checked. This allows for  
more flexible sample rate playback.  
4. In order to verify proper S/PDIF Output routing, open the Patchbay/Router  
page of the control panel software. In the "H/W Out S/PDIF" column, select the  
radio button named "WavOut S/PDIF." Now everything that is sent by your  
software to the "WavOut S/PDIF" device will be routed to the hardware S/PDIF  
output, and consequently to the DAT.  
5. Next let’s make sure the S/PDIF output format is correct. Open the S/PDIF page  
of the control panel software. Under Digital Output Format, choose "Consumer."  
Uncheck "Advanced" if it is checked previously. Now click on the "Restore  
Defaults" button to set the default S/PDIF outgoing status bits. This will disable  
copy protection and also set the emphasis to "none," allowing the DAT to accept  
and record the audio properly.  
6. Within your recording software, select "WavOut S/PDIF Delta-1010LT" as the  
audio output device.  
7. Start your DAT recording and then start your software playing. You should be able  
to hear the DAT material through your sound system. This verifies that the digital  
audio is making it into the DAT correctly.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
This section addresses potential problems that can occur in all operating system  
environments, with emphasis on hardware troubleshooting. Within the PC environment  
there are a limited number of hardware resources (I/O addresses, IRQs, and DMA  
channels) available for use. Since audio cards require many resources, most audio card  
installation problems arise from unavailable or improperly set resources. This is important  
enough to repeat:  
IMPORTANT: Most sound card installation problems result from  
attempting to use system resources (IRQs, address locations)  
already in use by other hardware (or software acting as “virtual”  
hardware) in the system.  
The Delta 1010LT has been carefully designed to minimize the number of resources  
consumed (it requires just one IRQ and does not require any DMA channel resources). It  
is also capable of sharing an IRQ in some cases. However, the possibility of resource  
conflicts still exists due to the nature of the Windows environment. Many resource conflicts  
are automatically recognized by Windows’ Plug-and-Play (PnP) system. When a resource  
conflict is detected, it is displayed in the Windows Device Manager. The Device Manager  
places a yellow exclamation point on top of the icon associated with the problem device.  
For an example of how the Device Manager should look when a Delta 1010LT is  
successfully installed, see the "Verifying Windows Driver Installation" section of this  
manual. If a yellow exclamation point does appear over your Delta 1010LT icon, you may  
have a resource conflict. There are several ways to approach this problem.  
NOTE: When resolving conflicts between PnP and non-PnP  
devices, it is recommended to re-adjust the resource settings of  
the non-PnP device first. Typically, Windows is only aware of the  
resource settings of the installed PnP devices and has no  
information available to it for adjusting the PnP devices’ resources  
around those of the non-PnP devices. The exceptions to this are  
when: (1) a non-PnP device has a true Windows 98/95 driver written  
for it, (2) the BIOS setup allows reserving an IRQ for a legacy device  
as opposed to a PnP device, or (3) resource requirements for the  
non-PnP device have been manually entered into the Windows  
Device Manager. In these cases Windows is aware of the non-PnP  
device’s resource requirements.  
One of the quickest ways to change the resources assigned to a PCI card like the  
Delta 1010LT is to merely relocate the card to another PCI slot. Before doing so, it is a  
good idea to locate the device in the Device Manager, highlight it, and click “Remove”  
(in 95/98) or select “Uninstall” from the Actions menu (in Win 2000). With the  
computer’s power off, remove the Delta 1010LT from its current PCI slot, move it to  
another available PCI slot, and turn your computer back on. More often than not, this will  
change the IRQ assignment of the Delta 1010LT when you re-enter Windows. After  
returning to Windows, follow the steps outlined in the "Verifying Windows Driver  
Installation" section of this manual. It might take more than one PCI slot relocation to find  
an open IRQ.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If relocating your card to another PCI slot does not cure the Delta 1010LT’s conflict(s),  
then you must do some further investigation to determine the exact nature of the  
conflict(s). Again, go to the Windows Device Manager, highlight the Delta 1010LT or  
other devices with conflicts and click the "Properties" button at the bottom of the Device  
Manager window. This will open the properties page for that device. Select the  
"Resources tab" in order to view the resource assignments, plus possible conflicts. You  
may learn more about a conflict by highlighting each item one-by-one (done by clicking  
on them, or scrolling through the list using your keyboard cursor keys) and examining the  
"Conflicting resource list:" at the bottom of the box.  
Sometimes it is possible that a resource problem is not showing up in the conflicting  
resource list or as a yellow exclamation point in the Device Manager. If you have any doubt  
about the configuration of your device (or just want to double-check), you can view all of  
the devices and their assigned resources by highlighting "Computer" at the top of the  
Device Manager list and clicking the Properties button. This will allow you to view a list  
of assigned IRQ numbers on the left, and the associated devices on the right. If a number  
does not show up in this list, it means that it is available for use. Look also for IRQs that  
are shared by more than one device. While the Delta 1010LT may share an IRQ with some  
devices, not all devices are capable of sharing IRQs. An entry that reads "IRQ Holder for  
PCI Steering" along with an installed PCI device (such as the Delta 1010LT) is normal. If  
you see another device showing up on the same IRQ as the Delta 1010LT (such as a video  
card, SCSI adapter, USB Host Controller or hard disk controller), then it is possible that  
this is the source of the conflict. Typically, if you move one of the conflicting cards to  
another PCI slot, an IRQ conflict will disappear.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Address conflicts are rare amongst PCI devices, but if there is no obvious IRQ conflict,  
why not check for I/O Address conflicts while in the Device Manager? You may view the  
list of assigned I/O addresses by selecting the "Input/output (I/O)" radio button below the  
"Interrupt Request (IRQ)" radio button at the top of the Device Manager page. I/O  
addresses are displayed as 16-bit hexadecimal numbers, therefore one might note that an  
address of 300h will read "0300" in this list.  
If scanning all the resource lists in the Device Manager does not provide an answer or clue  
to the resource conflict, you might want to exit Windows and do a final inspection of your  
computer’s BIOS setup. Some newer BIOS' (see your computer manual) allow the  
reservation of an IRQ for each PCI slot on the motherboard. This may be very handy in  
resolving IRQ assignments for PCI devices.  
Also, sometimes a BIOS is configured to direct a particular IRQ to an ISA legacy device  
(non-PnP ISA card), and needs to be told to look for a PCI/ISA PnP device (some systems  
default to this, especially with IRQs 3 and 4). Consult your computer or motherboard  
manual for advice on how to do this.  
With some systems you will reach the dead-end realization that you have no available  
IRQs – every one of them is assigned to some device in the system. This most typically  
occurs with pre-packaged computers made by the big-name O.E.M. computer companies.  
These computers have so many features packed into them that every IRQ is consumed. In  
this type of situation, some kind of reconfiguring or reprioritizing your system is in order.  
Optionally, Windows may allow you to create a second "hardware configuration" which  
disables some of the installed devices and makes their resources available for general use.  
See your Windows documentation for information on this subject.  
Windows 2000: ACPI mode is the default configuration for Windows 2000, which loads  
all devices configurable by the OS onto one IRQ. This will not work for most of us.  
Changing settings in the BIOS or moving devices to different PCI slots will not cause  
them to change IRQs.  
You can change your Windows 2000 system to “Standard PC” mode easily. This will  
cause your system to reconfigure ALL of the devices, including printer ports and COM  
ports. While this may sound like a scary proposition, doing so will then allow your devices  
to accept different IRQs, also allowing your BIOS to take control if your BIOS is capable  
of this.  
The best way to approach this is to change to Standard PC mode before you install your  
Delta card or any additional PnP expansion cards. If you’ve already installed these  
devices, you may need to completely start over to get each one to configure properly to  
its own IRQ. This means removing the device from the Device Manager, powering down,  
removing, and then installing each device one by one. It sounds sinister, but it is the best  
way to insure that each device configures properly.  
To remove a device from the Device Manager, right-click My Computer and select  
Properties. Click the Hardware tab, then select Device Manager. Locate the device in the  
list (clicking on the + sign opens the list for that device category), highlight it, then select  
“Uninstall” from the Actions menu. This is a good practice when reconfiguring a device,  
as it removes entries in the Registry for that particular device. Power down, and physically  
remove the expansion card from its PCI slot.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To change your system to Standard PC mode:  
1. Boot into Windows and open the Device Manager. Right-click the + sign next to  
“Computer.”  
2. Double-click the entry that appears under Computer, which should indicate that the  
computer is in ACPI mode. Click the Driver tab, then click the “Update Driver” button.  
3. The Upgrade Device Driver Wizard will appear. Click Next>. Select “Display a list of  
known drivers for this device...”and click Next>.  
4. Select the radio button “Show all hardware of this device class.” In the list on the right,  
select “Standard PC,”then click Next>. Follow the prompts, and restart your computer  
when instructed.  
Troubleshooting Tips for Frequently Asked Questions  
Problem: No Sound.  
Possible Cause 1: The Delta 1010LT hardware or software device drivers  
are not properly installed. See the installation sections of this manual for further  
information.  
Possible Cause 2: There is a resource conflict between the Delta 1010LT and  
another device in your computer. Check the Delta 1010LT configuration (Address, IRQ)  
against those of the other installed devices. If necessary, change the settings for the one or  
more of the devices.  
Possible Cause 3: Your application software has not been properly configured to  
use the Delta 1010LT as its audio output device.  
Possible Cause 4: Misrouted outputs in the Delta Control Panel. Check the Delta  
Control Panel’s Patchbay/Router page to verify output routing assignments. Also, make  
sure that if the output is routed from the digital mixer, that the mixer’s faders, solo and  
mute controls are set up properly.  
Possible Cause 5: Improper connections of the audio accessories. Verify that the  
Delta 1010LT analog audio outputs are properly connected to a digital mix deck or  
external mixer/amplifier, or the S/PDIF Out is connected to an external digital audio  
device capable of receiving S/PDIF.  
Problem: No visual activity on Audio Input volume (VU) meters of user software.  
Possible Cause 1: The Delta 1010LT input devices are not properly selected in  
the user’s application software.  
Possible Cause 2: If the software is recording from the Delta 1010LT’s monitor  
mixer device, be sure that the mixer’s faders, solo and mute controls are set up properly.  
Possible Cause 3: Improper connections to audio accessories.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem: Repetitious Sound.  
Possible Cause: An IRQ resource conflict. Often this will result in a small  
segment of sound (0.5 to 1 second) repeating itself over and over, sometimes completely  
locking up the computer. See the general troubleshooting suggestions at the beginning of  
this section.  
Problem: I’m getting some pops and clicks in my audio recording.  
Possible Cause 1: Input levels are too "hot," causing clipping or input distortion.  
Make sure you have the proper signal levels set on the Hardware Settings page of the Delta  
Control Panel. "Consumer" can handle hotter signals than "-10." If you find that you are  
still clipping at the Consumer setting, you will need to turn down the audio at the source.  
Possible Cause 2: If you are recording from the S/PDIF input, but you have the  
Delta 1010LT’s master clock set to something other than the S/PDIF input, you are  
recording an out-of-sync S/PDIF stream. This can result in lost or bogus samples being  
recorded.  
Possible Cause 3: Your application software may not have the proper audio  
buffer sizes set. Each software application handles this differently, but typically there is  
somewhere in the software’s setup to set the size of the playback and recording buffers  
used by the application. Some applications also require you to run a card calibration  
(sometimes called "profiling") the first time you use the software with a new audio card.  
Possible Cause 4: Some accelerated graphics cards use excessive amounts of  
system bandwidth, preventing the recording buffer of an audio card from keeping up with  
demand. This can cause clicks in the recording. Reducing or turning off the graphics  
card’s graphics acceleration feature often resolves this problem. In Windows, the level of  
graphics acceleration is accessed from Start |Settings | Control Panel | System |  
Performance | Graphics.  
Problem: The sound from the monitor mixer is muffled. It sounds as if it were  
running through a mixer with the treble control turned all the way down!  
Possible Cause: The current Delta 1010LT sample rate is too low. The monitor  
mixer is a digital device that runs at the current sample rate of the Delta 1010LT board. The  
frequency response of the mixer is roughly one-half of the sample rate. There is no way to  
prevent this lost frequency response while playing back or recording at a low sample rate.  
However, it may be prevented when the system is idle. See the "CODEC SAMPLE RATE"  
paragraph of the section ‘Hardware Settings Page’ for more information.  
Before You Call Midiman/M-Audio Technical Support  
The technical support team at Midiman/M-Audio wants to get you up and  
running in an efficient and timely manner. To help us help you, please read the  
following before calling technical support.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Use Midiman/M-Audio Resources  
In addition to your manuals, we also provide you with the following sources of  
information:  
Read Me Files: In your CD ROM, locate the Midiman/M-Audio product you own and  
open that folder. Find the appropriate Platform (Windows 95, 98, ME, 2000, Mac OS 9,  
X, etc.) that the folder may contain for your product. The Read Me Files often contain  
important information regarding updated drivers or driver installation procedures.  
Website: Studies show that over 75% of our calls can be avoided, thereby saving you the  
hold-time and inherent phone bill, by tapping into the resources our website has to offer.  
The Midiman/M-Audio web page is also available to you on your drivers CD ROM. There  
you will find FAQs, Tips & Tricks, and How-To Guides to walk you through installing  
your product as well as configuring it with some of today’s most popular software  
applications. You can also find updated web pages on the world wide web at  
How-To Guides and FAQs to read up on issues related to product drivers.  
Gather Important Information  
If you cannot find what you are looking for within the Midiman/M-Audio resources, you can  
call our technical support line. Please be ready to provide the following basic information.  
Product Name: Please know the exact name of the Midiman/M-Audio product you own  
(make and model— Example: “Midisport 2x2”, “Delta Audiophile 2496”). Tell the tech  
how long you have owned the product. If you start with the frame of mind of providing  
basic information, your tech call will go smoothly from the get-go.  
System Information: The next most important piece of information is what computer  
platform you are using—i.e. Is this a Macintosh or a PC, and what Operating System  
(O.S.) are you running with it Windows 98, ME, etc. or Mac OS 9.1, 9.2 etc.?  
Also tell us what kind of processor you are using (Athlon, G4, Pentium, etc.) and how  
much RAM you have.  
If you are a PC user, be prepared to let us know the following:  
What kind of chipset does your motherboard has? (Consult your motherboard manual or  
computer’s manual for help with this).  
Are devices such as Modems, Soundcards, Ethernet adapters embedded on the  
motherboard, or connected via USB, ISA, or PCI. How many PCI/ISA slots do you have  
and are you using any USB hubs?  
Are you recording to IDE or SCSI hard drives?  
These are extremely important pieces of information to know when calling us.  
Finally, Mac users using OS X must know what their System Administrator Password is.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Symptoms: Please be ready to describe the symptoms to the best of your abilities  
(crackle, stuck notes, jitter, etc.) and whether or not they are consistent (Do they happen  
at the same place at the same time —each time? Etc.). You may also want to note when  
you started experiencing these problems and whether it was related to any specific  
incident or not.  
After gathering this information, please have your telephone near your computer and/or  
Midiman/M-Audio product. If you’re calling from a cell phone, please prepare plenty of  
battery power as well as make sure that a cellular signal can be clearly reached where you  
are calling from. Sit back, try to relax and then dial. Our top-notch technical support team  
will be ready to help you fix your problems. Thanks for using Midiman/M-Audio products.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix A - Technical Specs  
Analog Audio  
Peak Analog Input Signal:  
+14.2 dBu (+4dBu setting  
+2.1dBV (-10dBV setting)  
Peak Analog Output Signal:  
+14.0dBu (+4dBu setting),  
+2.0dBV (-10dBV setting)  
Dynamic Range:  
Outputs:  
Inputs:  
101.5 dB (a-weighted),  
99.6 dB (a-weighted)  
THD (at 0dBFS):  
Outputs:  
Inputs:  
less than 0.002%,  
less than 0.002%  
Frequency Response:  
22Hz - 22kHz, -0.2, -0.4dB @ 48kHz;  
22Hz - 40kHz, -0.2, -0.7dB @ 96kHz  
Input Impedance:  
Input Connectors:  
Output Connectors:  
9.5k ohms minimum  
RCA, gold plated  
RCA, gold plated  
Digital Audio  
Digital Input Format:  
Digital Input Sample Rate:  
Digital Output Format:  
S/PDIF coaxial  
32kHz to 100kHz.  
S/PDIF coaxial, or AES/EBU data stream  
over S/PDIF coaxial.  
Digital Output Sample Rate:  
8kHz to 100kHz.  
Adapter Resource Requirements  
IRQ:  
One required  
I/O Addresses:  
Four blocks: 32, 16, 16, and 64 bytes  
DMA Channels:  
None required  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B-If You Use An External Mixer...  
Our main objective is to get the signal we want to record to the Delta 1010LT, and to  
monitor the outputs from the Delta 1010LT. The 1010LT has a mixer contained on its chip  
that allows you to mix hardware inputs and software outputs and send it to an analog  
stereo output pair and/or the S/PDIF out. The 1010LT also allows you to record that mix  
into your music software as a hardware input. Still, some of you may choose to use a  
mixing console to achieve your multi-tracking goals.  
A mixing console (sometimes referred to as mixing ‘board’ or ‘desk’) that is designed for  
multi-track recording has the ability to fulfill these two basic functions -- getting the  
signal to the recording device, and receiving the outputs of that recording device for  
mixing or monitoring. In this sense, a recording console is two mixers in one. A mixer  
designed for recording will also have the ability to send to one or more mixdown decks,  
to monitor these mixdown decks, to control separate control room and studio listening  
levels, as well as other recording-specific functions.  
There are two basic layouts for the recording console, "split section" and "in-line." The  
split section design is arranged with a recording or ‘channel’ section (to send the signal to  
the recording device) side-by-side with a monitoring section (to receive the outputs of the  
recording device). The in-line design has the recording and monitoring sections "in line"  
within each channel module, so that each channel has two line inputs.  
The recording section is distinguished by its bussing system, which takes the recording  
channel signal through a summing matrix to multiple outputs- usually in multiples of  
eight. It could be said that an ‘8-buss system’ is designed for 8 track recording, and a  
24-buss system for 24 track recording, etc., but this is not written in stone.  
What we are describing here is the extreme- a professional, costly piece of gear that has  
been purchased for this one specialized purpose. There are features inherent in other types  
of consoles, however, that will allow us to perform these two separate functions of  
recording and monitoring. A sound reinforcement or a broadcast console, and in some  
cases a recording console, might offer a bussing system in the form of "sub-mix outs."  
These are usually arranged in stereo pairs with a set of level control faders for each pair.  
This configuration can be effectively used for recording, as long as the record channels  
are taken out of the stereo buss. The difference here is that there is no real distinction  
between the recording and monitoring sections.  
Some line mixers have a number of effect or auxiliary sends for each channel. These sends  
will have their own individual level control and will receive the signal either pre fader or  
post fader, i.e. either independent or dependent on that channel’s fader level. It is possible  
to use these "aux sends" to send a signal to the recording device. A pre fader send is  
certainly preferable, since this will allow for a recording level that is separate from the  
monitoring level.  
The bottom line here is that you can not use the ‘main output’ of your mixer to send a  
signal to the recording device, and then take the outputs of that recording device back into  
the mixer (whose signal also goes to the main out). This creates a feedback loop, bad for  
your eardrums and bad for your equipment.  
One modern console design gets around that by offering an "alt out," which is an alternate  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
stereo buss or output. When selecting ‘alt out’ on a channel, it mutes that channel to the  
stereo buss and redirects it to the alt out buss. This could be viewed as a 2-buss system,  
and can be used effectively for recording purposes.  
In our Typical Setup 1 and 2 in the previous section, we used pre-amps to handle the  
recording. A line mixer that simply received the line outputs from the 1010LT and mixed  
them to stereo could handle the monitoring needs. Hopefully, the information here will  
give you some insight into how to use the gear that you own, or what to look for if you  
are seeking additional equipment to facilitate your hard disk recording.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited Lifetime Warranty  
MIDIMAN warrants that this product is free of defects in materials and workmanship  
under normal use so long as the product is: owned by the original purchaser; the original  
purchaser has proof of purchase from an authorized MIDIMAN dealer; and the purchaser  
has registered his/her ownership of the product by sending in the completed warranty  
card.  
This warranty explicitly excludes power supplies and included cables which may become  
defective as a result of normal wear and tear.  
In the event that MIDIMAN receives written notice of defects in materials or  
workmanship from such an original purchaser, MIDIMAN will either replace the product,  
repair the product, or refund the purchase price at its option. In the event any repair is  
required, shipment to and from MIDIMAN and a nominal handling charge shall be born  
by the purchaser. In the event that repair is required, a Return Authorization number must  
be obtained from MIDIMAN. After this number is obtained, the unit should be shipped  
back to MIDIMAN in a protective package with a description of the problem and the  
Return Authorization clearly written on the package.  
In the event that MIDIMAN determines that the product requires repair because of user  
misuse or regular wear, it will assess a fair repair or replacement fee. The customer will  
have the option to pay this fee and have the unit repaired and returned, or not pay this fee  
and have the unit returned unrepaired.  
The remedy for breach of this limited warranty shall not include any other damages.  
MIDIMAN will not be liable for consequential, special, indirect, or similar damages or  
claims including loss of profit or any other commercial damage, even if its agents have  
been advised of the possibility of such damages, and in no event will MIDIMAN's  
liability for any damages to the purchaser or any other person exceed the price paid for  
the product, regardless of any form of the claim. MIDIMAN specifically disclaims all  
other warranties, expressed or implied. Specifically, MIDIMAN makes no warranty that  
the product is fit for any particular purpose.  
This warranty shall be construed, interpreted, and governed by the laws of the state of  
California. If any provision of this warranty is found void, invalid or unenforceable, it will  
not affect the validity of the balance of the warranty, which shall remain valid and  
enforceable according to its terms. In the event any remedy hereunder is determined to  
have failed of its essential purpose, all limitations of liability and exclusion of damages  
set forth herein shall remain in full force and effect.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  

La Crosse Technology Clock WT 8008U User Manual
La Crosse Technology Portable Radio WD 3104U User Manual
La Crosse Technology Weather Radio K84315 User Manual
Lathem Time Clock 5000E Plus User Manual
Lennox Hearth Stove SDVCS User Manual
Linear Video Game Controller AP 1 User Manual
Lochinvar Water Heater CB 2066 User Manual
Loewe Projector Individual Sound Projector User Manual
Mad Catz Water Pump 5MPRA6C 146 User Manual
Micro Innovations Network Card USB50BT User Manual