Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
v
v
v
Carefully remove all packing from box.
Put all the oil from the phial supplied into the bearing housing - NOTE Remove bearing-housing dustcap.
Carefully put the Inner Platter into the bearing housing supporting it as it sinks down to prevent damage to
the bearing surfaces.
v Fit the Belt around the inner platter and motor pulley (see “Speed Selection"). NOTE – BE
CAREFUL NOT TO GET OIL ON THE BELT
v
Fit the Outer Platter and Mat onto the inner platter.
If your deck is fitted with a Linn AKITO tonearm, set the Tracking Weight as follows:-
NOTE – the cartridge should be fitted to the arm prior to this procedure – remove the arm from the turntable when
fitting the cartridge to the arm to prevent damaging the tonearm bearing during fitting.
v
Make sure the arm is clipped into its rest, the bias is off and the lift/lower device is lowered. With
tracking dial facing backward, screw the counterweight clockwise (as you look at the dial) onto the arm,
pushing gently to engage the thread. Remove the stylus guard. Holding the fingerlift, unclip the arm and
move it to between its rest and the platter.
Download from Www.Somanuals.com. All Manuals Search And Download.
v
v
Turn the counterweight to the position which balances the arm, i.e: where the stylus is floating at about
record height. Clip the arm back into its rest. Turn the tracking dial while holding the counterweight until
'0' is aligned with the line on top of the arm.
Check the arm is still balanced. If not you have moved the counterweight when setting the tracking dial, so
re-balance the arm and re-set the tracking dial to '0'. Turn the counterweight clockwise (as you look at the
dial) to the desired tracking force. Set the bias to the same value. (See General Installation for more
information).
v
Check the arm height is correct. The arm-tube should be parallel to the record surface. Adjustment can be
made by loosening the arm height adjustment screw with a 4mm hexagon key, moving the arm to the correct
height and locking the screw. To set the correct torque tighten the screw firmly using the alien key in
position 1, then turn the key to position 2 and tighten no more than a further 1/8 of a turn.
OVERTIGHTENING CAN WRECK BEARINGS.
Download from Www.Somanuals.com. All Manuals Search And Download.
SITING
Ensure the surface on which the turntable is to be used is level. For best results we recommend the following:-
FLOOR MOUNTING
Place deck on a small, light, rigid table e.g. small coffee table. Ensure the table is
sitting firmly on the floor and not rocking.
WALL MOUNTING
Wall mounting may be preferable where a highly sprung floor exists or where there is
risk of damage by children. The shelf used should be light and rigid, and it should be fully supported by, but not
firmly screwed or glued to its brackets.
To allow the lid to open fully, a clearance of 3" (7.5cm) is required behind the plinth and at least 13" (33cm)
above
Fit the arm cable to the arm pillar taking care to push it all the way home. The connector may be locked in place
with the small Alien screw on the side of the pillar (don't over-tighten). Ensure that neither the mains cable
nor the arm lead are under tension or interfere with the feet as this will prevent the suspension from working
correctly.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The power switch is on the underside of the plinth at the front left-hand side. A label indicates direction for
ON and OFF. This label is removable.
Lift and lower the lid carefully as it is coupled to the suspended plinth. If dropped or roughly handled it may
cause the arm to jump.
NOTE You may notice a little noise from the motor at first. This should disappear when the motor has
bedded-in for a few days.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEED SELECTION
To change the speed of the BASIK turntable, switch off, remove the mat and outer platter and move the belt to
the other level on the stepped pulley.
The larger diameter will give 45rpm, the smaller will give 33rpm.
If changing to 45rpm it is advisable to start up the motor with only the inner platter in place, to allow the belt
to find a stable position.
Once the belt is running straight, switch off, replace the outer platter and switch on again.
NOTE It is important to keep the belt clean - if it is contaminated with oil the sound quality will be degraded
and the belt may jump off the 45rpm pulley. If this occurs, clean the bell and pulley with a little solvent -
surgical spirits or other non-residue solvents.
Download from Www.Somanuals.com. All Manuals Search And Download.
TURNTABLE MAINTENANCE
The BASIK is designed for a long operational life. To preserve the appearance and maintain the performance of
your dock, you should note the following points:
OUTER PLATTER
Clean with a soft, dry cloth. DO NOT use any abrasive cleaner as this will remove the
protective lacquer and cause corrosion.
MAT
The felt mat can be cleaned with masking tape.
MOTOR
The motor pulley should be cleaned periodically. Remove the outer platter and belt,
and gently clean with a cloth impregnated with isopropyl alcohol or other non-residue
solvents.
PLINTH
OIL
This can be cleaned with a light duster or slightly damp cloth - make sure the
stylus guard is in place before you start. If you have to remove an oil slain from the
plinth, use a soft cloth and solvent.
The oil supplied for the bearing provides life-long protection. If the oil is lost from
the bearing housing it must only be replaced by factory-supplied oil which is available
from your Linn dealer. The turntable should never be operated without oil.
LID
The best method is to remove any dust with a damp cloth without any rubbing action
and then use a soft duster. Lids are more often damaged by cleaning than in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SYSTEM INSTALLATION
TRACKING WEIGHT & BIAS
Every arm and cartridge combination has an optimum tracking weight which your dealer will have advised you of.
RECORD CLEANING
Most record cleaning devices do more harm than good. The best method of cleaning records is to lot the stylus
remove any dirt in the groove, then clean the stylus.
STYLUS CLEANING
It is important that the stylus is kept scrupulously clean. We have found that dry vibrating pad cleaners work
well. Alternatively, Linn dealers can supply cleaning paper which is easy to use and gives excellent results.
CLEAN CONTACTS
Electrical contacts in a hi-fi system must be kept mechanically sound and clean. A poor contact between the
cartridge and arm will degrade performance. Checks on all contacts should be performed periodically.
INTERCONNECT LEADS
We recommend and supply good quality copper cable for interconnect leads and advise 4mm so multicore copper
cable, such as Linn K20, for speaker leads.
SPEAKER PLACEMENT
Speakers should be positioned correctly and should be mounted on rigid stands which are sitting firmly on the
floor and not rocking.
NOTE Linn speakers are designed to be placed close to the wall
TRANSPORTATION
Always keep all the packing for your BASIK turntable.
When transporting the BASIK turntable, remove the counterweight from the arm, remove the arm from the
plinth, remove the inner platter from the bearing housing and place it in its position in the packing. Replace the
bearing cap to prevent oil spillage.
If the deck is to be shipped anywhere it is important to pack it properly in the original packing, otherwise
damage will occur.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
GUARANTEE
The unit is guaranteed under the conditions that apply in the country of purchase.
Unauthorised servicing or dismantling of this turntable will invalidate the manufacturer's warranty. If you are
in any doubt, please contact your nearest Linn dealer.
In addition to any statutory rights the customer may have, we undertake to replace any parts, which have failed
due to faulty manufacture.
Keep a copy of the sales receipt, as this will establish the purchase date of the turntable.
Refer all enquiries to authorised dealers only. For information on your nearest dealer, contact the Linn factory
in the UK or an overseas distributor.
LINN PRODUCTS LTD., FLOORS ROAD, WATERFOOT, EAGLESHAM,
GLASGOW G76 OEP. SCOTLAND.
TELEPHONE
FACSiMILE
++44 (0)141 307 7777
++44 (0)141 644 4262
Download from Www.Somanuals.com. All Manuals Search And Download.
|