INSTALLATION INSTRUCTIONS FOR PART 99-7603
APPLICATIONS
Nissan Versa
2007-2011
99-7603
KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Mount Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Trim Plate
Harness & Antenna Connections (sold separately)
• 70--7552 - Nissan Harness 07-up
• 40-NI12 - Nissan Adapter 07-up
B
A
D
C
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603 DASH DISASSEMBLY
NISSAN VERSA 2007-2011
A
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
2
3
Unclip and remove the panel above
the radio. (Figure A,B)
Remove (2) Phillips screws securing
the radio trim panel then unclip and
remove the entire panel surrounding
the radio and a/c controls. (Figure C)
B
C
1
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603 DASH DISASSEMBLY
NISSAN VERSA 2007-2011
D
4
5
Remove (4) Phillips screws securing
radio, unplug and remove radio.
(Figure D)
RADIO
CD
PRESET A-B-C
LOAD
DISP
CLOCK
6CD CHANGER
RPT
SCRL
1
2
3
4
RDM
SEEK
TUNE
FF-REW
FOLDER
PUSH
PWR
TRACK AUDIO
FILE
5
6
AUX
SCAN
CAT
VOL
Remove (4) Phillips screws securing
each bracket to factory radio. (Retain
these brackets to be re-used during
double DIN or stacked ISO kit assem-
bly.) (Figure E)
CH
Continue to kit assembly.
E
2
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603 KIT ASSEMBLY
DIN MOUNT RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Note: You will need to remove the
aftermarket radio’s trim ring if
equipped.
1
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
2
3
Slide the aftermarket radio into the
cage until it snaps into place. (Figure B)
Attach the trim plate supplied with the
kit to the front of the radio housing
B
assembly. (Figure B)
Continue to final assembly.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603 KIT ASSEMBLY
ISO MOUNT RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
Note: The following modification
A
will need to be made to both
ISO brackets when using the ISO
mount radio provision. Cut or trim
the area shown from the ISO
bracket. (Figure A)
1
Mount the ISO Brackets to the after-
market radio using the screws sup-
plied with the radio. (Figure B)
2
3
Slide the radio into the radio housing
until it snaps into place. (Figure C)
FRONT
FACE-
RIGHT
Attach the trim plate supplied with
the kit to the front of the radio hous-
ing assembly. (Figure C)
SIDE
BRACKET
Continue to final assembly.
C
B
4
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603 KIT ASSEMBLY
DOUBLE DIN MOUNT RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Mount the factory brackets (removed
from factory radio during disassembly)
to the sides of the double DIN radio
using screws supplied with the double
DIN radio. (Figure A)
1
2
Place the double DIN trim plate on the
front of the double DIN radio. (Figure B)
Continue to final assembly.
B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603 KIT ASSEMBLY
STACKED ISO UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Mount the factory brackets (removed
from factory radio during disassembly)
to the sides of the stacked ISO units
using screws supplied with the ISO
units. (Figure A)
1
2
Place the double DIN trim plate on the
front of the stacked ISO units. (Figure B)
Continue to final assembly.
B
6
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603
NOTES
8
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603
NOTES
9
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7603 INSTRUCTIONS
1-800-221-0932
REV. 10/06/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7603
Download from Www.Somanuals.com. All Manuals Search And Download.
|