1. PRODUCT DESCRIPTION
2. EMITTER DETAILS
Encore Multi-Room Audio
Distribution System
The Model 2171-4 Single-head Infrared (IR) Emitters are supplied in
a package of four and are used with the Linear Encore Multi-Room
Audio Distribution System, ENC-SIWP source input or ENC-LIWP
local input wall plates. These generic emitters can also be used
with Linear’s video hubs, 2100A and 2010 in-wall interface, or with
a 5500 series IR enabled modulator connected to a video hub.
Model 2171-4 IR Emitter
Side View
Top View
1/4"
NOTE: White side
stripe is positive (+)
3.5 mm mono
mini plug
(
+
)
2171-4
5/16"
Single-head
IR Emitter
(4-pack)
(
–
)
Each emitter contains a tiny infrared LED housed in a miniature,
injection molded plastic shell. The emitters have adhesive backing
for mounting. An emitter can be installed directly on the IR sensor
window of the controlled source component or in a suitable nearby
location.
9/16"
7 FT
3 FT
Internal
IR Emitter
The emitter's shell, though dark in
appearance, is transparent to
infrared light. Commands from
handheld remote controls will pass
through the emitter case to the
source component.
High
Output
Side
Low
Output
Side
Installation
Instructions
An IR emitter repeats IR remote control signals received at a room
station keypad or IR target from a handheld IR remote control.
When an IR signal is detected at a target, the signal is sent to the
IR OUT jacks on the wall plates or device. An IR emitter connected
to the IR OUT jack, repeats the same IR signal to the source
component. This allows IR remote control of source components
that are located away from the IR target.
Clear adhesive layer
(Replace, if necessary,
with a short piece of
2-sided supplied)
Emitter
Shell
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
Mini-wire
Lead
3. ATTACHING EMITTER TO COMPONENT
4. CONNECTING EMITTER TO SOURCE
LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twenty
four (24) months. This warranty extends only to wholesale customers who buy direct
from Linear or through Linear’s normal distribution channels. Linear does not warrant
this product to consumers. Consumers should inquire from their selling dealer as to
the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the
part of Linear LLC for consequential damages arising out of or in connection with
use or performance of this product or other indirect damages with respect to loss
of property, revenue, or profit, or cost of removal, installation, or reinstallation. All
implied warranties, including implied warranties for merchantability and implied warranties
for fitness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu
of all other warranties express or implied.
IR Controlled Components
IR Sensor
Window
Cabinet Door
Connect IR emitter to source
input wall plate IR OUT jack
or to the IR OUT jack provided
on other sources
Emitter attached to
front cabinet door directly
opposite IR sensor window
Emitter attached directly
to IR sensor window
Shelves
> Peel off the adhesive cover and affix the emitter to the center of the IR sensor
window on the controlled component's front panel
All products returned for warranty service require a Return Product Authorization Number
(RPA#). Contact Linear Technical Service at 1-800-421-1587 for an RPA# and other
important details.
> In some cases, it may be difficult to find the location of the IR sensor on the
component. Consult the owner's manual of the unit for the IR sensor location.
To IR emitter
Shelves
ENC-SIWP
Source Input
Wall Plate
Sensor attached on shelf directly
above or below IR sensor window
Copyright © 2009 Linear LLC
P691
Download from Www.Somanuals.com. All Manuals Search And Download.
|