Lightolier Work Light IS26600 User Manual

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING TRACK  
INSTRUCTION SHEET NO.  
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal code  
specifications. To assure full compliance with codes and regulations, check with your local electrical inspector  
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.  
IS:26600  
Save these instructions for maintenance reference  
and refer to them when additions to or changes in the track configuration are made.  
A0397  
Page 1 of 4  
Installation Instructions for ProSpec Track Lighting--  
Recessed Feed Track and Plain Track Units.  
ProSpec™ track lighting is designed to support and energize ProSpec™ Lytespots® which can be  
attached anywhere along the track. It is a four conductor system, continuously grounded through-  
out, to be supplied by two single 120V, 20 amp, 60Hz branch circuits. It is not intended for use with  
a power cord or convenience receptacles. ProSpec™ is listed by Underwriters Laboratories, Inc. It  
may only be used with electrical fittings identified for use with ProSpec™ track.  
IMPORTANT SAFETY INSTRUCTIONS  
Read all Track, Connector, Feed-in Kits, and Accessory Instruction Sheets before  
installing any ProSpecTrack item. When installing or using this track system, basic  
safety precautions should be followed:  
Read all instructions before installing the track system.  
Do not install in wet media (concrete, plaster, etc.).  
This track system is intended for installation in accordance with the National  
Electrical Code and Local or Federal Codes.  
Do not install this track in wet or damp locations.  
Do not install any part of this track system less than 5 feet above floor.  
Do not install any fixture assembly closer than 6 inches from any curtain, or similar  
combustible material.  
To prevent electrical shock, turn off electricity at fuse box before installing the track  
or adding to or changing the configuration of the track.  
Instructions for grounding per instruction sheet of the feed-in kit used must be  
followed. Failure to do so may result in a hazardous condition.  
Use #12 ga. AWG solid wire only (not stranded wire) for supply to track.  
Observe polarity, white supply lead (neutral) to contact marked “NEUT” on screw  
terminal connectors.  
Do not exceed 4 feet between mounting points.  
Do not attempt to energize anything other than track lighting fixtures on the track.  
To reduce the risk of fire and electrical shock, do not attempt to connect power tools,  
extension cords, appliances and the like to the track.  
SAVE THESE INSTRUCTIONS  
FALL RIVER, MASSACHUSETTS 02720  
MONTREAL, QUEBEC, CANADA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTRUCTION SHEET NO.  
Instructions for Recessed ProSpec Track  
Power Feed to Track  
IS:26600  
A0397  
Page 3 of 4  
DIRECT POWER FEED TO "FEED" TRACK  
Use solid 12 ga. copper wire when feeding the track. The feed track accepts  
two separate 120 V, 60 Hz branch circuits. Each circuit must not exceed the  
20 amp capacity of the track system.  
Electrical  
Connector  
Top Plate  
Knock out  
FEED FROM ABOVE TRACK (Fig E):  
•Remove Bottom cover and save.  
•Remove Knockout in Top Plate.  
•Remove Top Plate from Track  
FeedTrack  
•Secure electrical connector (by others; 3/8 size recommended) to Top  
Plate using the Nut provided. Position connector locking screws such  
that the screws will be hidden behind the track width.  
•Attach Top Plate to track.  
Bottom Cover  
•Pass wires through connector and secure the cable or conduit to the  
connector. The track must not support the cable. Use separate support  
for securing the cable to the building structure.  
FIG. E  
Use 12 ga. solid copper wire for feed  
connections including ground.  
•Secure the track to the ceiling (see mounting on previous page).  
•Form the wires in the Feed track to the connector terminals  
(see FIG. F). Cut and strip each wire. Attach wires to the screw  
terminals. Wires must be tightly held in the screw terminals. Neutral  
wires must be attached to screw terminals marked "NEUT”. Ground  
wire must be attached to the green ground screw.  
Circuit 2  
Neutral 2  
Circuit 1  
Neutral 1  
•Snap Bottom Cover into the track.  
Neutral  
Terminals  
Power  
Terminals  
.50  
Two wires may be  
attached to one  
screw terminal.  
Ground Terminal  
FIG. F  
FEEDING ALONG THE TRACK LENGTH (Fig. G)  
A floating splice box may be used to feed the "Feed Track" from along the  
tracks length. The floating splice box can be mounted anywhere on the track  
up to 4' from the end of the track. The wires are passed along the top of the  
track and into the feed end of the track. The floating splice box may  
only be used when there is accessibility to the splice box after the  
installation is complete.  
FloatingSpliceBox  
Dead End  
Floating Splice Box (Cat. no. 26660) sold separately. See instructions  
supplied with 26660 for complete installation details.  
Wire Cover  
FeedEnd  
Feed Track Unit  
FIG. G  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTRUCTION SHEET NO.  
Recessed ProSpec Track  
IS:26600  
A0397  
Page 4 of 4  
Structural  
Impediment  
Power  
Feed  
POWER CONTINUITY FROM  
A STRAIGHT RUN OF TRACK  
u
t
Mini Coupler or  
In-Line Connector  
o
Power  
Feed  
P
This can be accomplished by using Feed Tracks coupler together, by using  
Feed Track with a power extension connector, or by using Plain Track with  
multiple Power Extensions. The Power Extension Connector is sold  
separately (CAT, NO. 26646WH). See instructions with the power extension  
for installation details.  
Feed Track  
Feed Track  
Feed Track  
or Power Extension  
Connector  
NOTE: THIS TRACK SYSTEM IS NOT POLARIZED. Connectors can be  
installed into both sides of the Plain Track and in any orientation. There is  
no key that will prevent insertion of the connectors. Connectors cannot be  
attached to the feed side of the Feed Track. Electrical polarity is maintained  
by proper wiring of the circuits. (See Fig F.)  
Power  
Feed  
u
t
o
Power  
Feed  
P
Feed Track  
Power  
Extension  
Connector  
Feed Track  
or Power Extension  
Connector  
Power  
Feed  
u
t
Power  
Feed  
o
P
Power  
Extension  
Connector  
Plain Track  
Power  
Extension  
Connector  
Feed Track  
or Power Extension  
Connector  
Power Extension  
Connector  
FIG. H  
FIELD CUTTING TRACK  
Aluminum Track Housing  
•Remove and save the Dead End Cover.  
•Cut the track using a metal cutting blade (preferably in a miter box to  
obtain a square cut)  
•Remove ALL burrs and sharp edges from the cut surface of the track  
being careful not to destroy the integrity of the track geometry. There  
should be no burrs between the copper wire(s) and the aluminum track  
housing.  
Open copper conductor  
gap after cutting  
•If an electrical connector is being installed into the cut section, open  
the GAP of all copper wires using a wedging tool (such as a flat blade  
screwdriver). CAUTION; DO NOT OPEN THE GAP MORE  
THAN 3/16" FROM THE EDGE OF THE TRACK EXTRUSION.  
•Insert the Dead End Cover into the end of the track run.  
Open gap 3/16" max.  
from track edge. Typical  
for all copper wires.  
Dead End  
FIG. I  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kyocera Printer FS 3700 User Manual
Learning Resources Baby Toy LER 6954 User Manual
Learning Resources Telephone Accessories LER 0935 User Manual
Lenovo Tablet 2290XF2 User Manual
LG Electronics Microwave Oven LTRM1240SB User Manual
LSI Network Card 7202CP User Manual
LST Smoke Alarm ECO1003 User Manual
Makita Impact Driver BTL061Z User Manual
Marmitek Home Security System DOORGUARD300TM User Manual
Maytag Clothes Dryer W10160251A User Manual