Lightolier Work Light A E User Manual

Calculite® HID A-E  
Page 1 of 1  
Auxiliary Lighting Systems For Temporary H.I.D. Lamp Outage  
Mode of Operation  
Auxiliary Lighting for Recessed HID Luminaires and Cylinders (A)  
H.I.D. lamps require a “warm-up” period of 5 to 10 minutes to reach full output.  
Additionally, when these lamps are extinguished they must cool for 5 to 15  
minutes before they will relight. Outage can be caused by momentary power  
failure, substantial voltage reduction or cycle changes.  
Initial Start:  
H.I.D. lamp and tungsten halogen lamp both energized. H.I.D.  
lamp starts warming up; tungsten-halogen lamp at full output.  
To provide a minimum level of illumination, a double-contact bayonet socket and  
solid-state switching device, (for use with a 120V tungsten-halogen lamp) operate  
during initial H.I.D. lamp warm-up, or cold-off-and-restart period.  
Partial Warm-Up:  
H.I.D. lamp reaches approximately 60% light output; tungsten-  
halogen lamp switched off.  
The tungsten-halogen lamp remains on until the HID lamp reaches approximately  
60% of its light output.  
Note: The auxiliary is not emergency lighting and will only operate when there is  
power to the luminaire. The AUX system is available for magnetic ballast either  
120V or 277V branch circuits with a ballast tap supplying 120V to the tungsten-  
halogen lamp. 120V electronic ballast can be operated with 120V branch circuit.  
For 277V, electronic, consult factory.  
Full Warm-Up:  
H.I.D. lamps at 100% light output.  
To specify: add suffix “A” to Catalog Number for Recessed H.I.D. Fixture.  
See fixture specification sheets for compatibility.  
“Hot” Restart:  
H.I.D. lamp and tungsten-halogen lamp both energized. H.I.D.  
lamp too hot to start; tungsten-halogen lamp at full output. After  
H.I.D. lamp cools down and starts, cycle begins as in “Initial  
Start” above.  
Emergency Lighting for Recessed HID Luminaires (E)  
A tungsten-halogen lampholder, (without the switching device) prewired with  
#18AWG SF2 leads in a 5/16" x 26" long flexible greenfield cable, is provided  
with the luminaire for attachment to an AC 60 cycle power supply. Power supply  
by others.  
To specify: add suffix “E” to Catalog Number for Recessed H.I.D. Fixture.  
See fixture specification sheets for compatibility.  
Maximum Tungsten-Halogen Lamp Wattage  
HID Lamp  
Tungsten-Halogen Lamp T-4, 120V  
Double-Contact Bayonet  
39W-70W T6  
150W T6  
39W-150W ED17, PAR  
175W  
75W  
75W*  
100W  
150W  
150W  
250W-400W  
*Applicable for any reflector trim with “CL” finish.  
Job Information  
Type:  
Job Name:  
Cat. No.:  
Lamp(s):  
Notes:  
Lightolier a Genlyte Thomas Company  
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710  
We reserve the right to change details of design, materials and finish.  
© 2004 Genlyte Thomas Group LLC (Lightolier Division) • B0704  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lanier Headphones 480 0066 User Manual
Lasko Fan 760000 User Manual
LG Electronics Cell Phone VX4270 User Manual
Life Fitness Home Gym C04 User Manual
Life Fitness Watch GK61 00002 0008 User Manual
Lightolier Indoor Furnishings T7032 User Manual
Marmitek Home Safety Product MS845 User Manual
Mattel Motorized Toy Car M8487 0920 User Manual
Maxis Cell Phone 73315 V User Manual
Melissa Styling Iron 635 088 User Manual