Models RNC120F/120ERV
Application
Shipping and Packing List
Package 1 of 1 contains:
1 - Assembled ventilator
1 - Bag assembly containing:
Heat Recovery Ventilators (HRV) are designed to provide
fresh air while exhausting an equal amount of stale air.
The HRV is equipped with an aluminum core. The device
uses the stale air that is being exhausted to condition the
fresh air as it is being brought in.
4 - Hanging straps
1 - Installation manual
1 - Remote electrical control box
1 - Bag containing sealant putty
General
These instructions are intended as a general guide and do
not supersede local codes in any way. Consult authorities
who have jurisdiction before installation.
Required Tools
Installation Tools
•
•
•
•
•
•
•
•
tin snips
•
•
large zip ties
fabric flexible duct
- class I rated
assorted screw drivers
electric drill
hammer
wire strippers
knife
Table of Contents
•
•
•
•
mastic tape
alum. foil duct tape
Shipping and Packaging List ......................................1
Required Tools............................................................1
Application ..................................................................1
General .......................................................................1
Engineering Data.....................................................2-5
Installation Instructions ...............................................6
Clearances & Requirements.......................................7
Installation..............................................................7-10
Application Illustrations........................................11-16
Remote Control Devices...........................................17
Wiring the Controls ...................................................18
Electrical ..................................................................19
Operation ..................................................................20
Wiring Diagrams .......................................................21
Interlocking HRV to Furnace.....................................22
Air Flow Balancing...............................................24-25
Troubleshooting ........................................................26
Maintenance ............................................................27
zip ties
1
caulking gun
smoke pencil
/
2” I.D. drain hose
Balancing Tools
•
Pitot Tube Balancing Kit
[Case, 8 ft. vinyl tubing, Pitot tube,
magnehelic gauge (0 - 0.25”), and
mounting plate]
or
•
Pitot Tube with instructions
and Digital Manometer (with resolution of
0 - 0.25” - must read to 1/100ths of an inch)
Optional Accessories
•
•
•
•
20 Minute Fan Timer
Wall Mounted Dehumidistat
Weather hood Kit
Round Diffuser
4” (100mm)
5” (125mm)
6” (150mm)
8” (200mm)
•
Kitchen Grille
- may be required by code for kitchen applications
- contains removable grease filter
* LEAVE FOR HOMEOWNER
TI-CCU-001
NOTE: Due to ongoing research and product development, specifications,
0108
ratings and dimensions are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
Engineering Data
Model RNC120F
Option 1 - Standard Duct Configuration Dimensions inches
EXHAUST AIR
FROM BUILDING
TOP VIEW
HANGING
STRAPS
FRESH AIR
TO BUILDING
EXHAUST
AIR FROM
BUILDING
FRESH AIR
FROM OUTSIDE
PLUG-IN CONNECTOR
FOR CONNECTING TO
REMOTE ELECTRICAL
BOX
FRESH AIR
FROM
OUTSIDE
EXHAUST AIR
TO OUTSIDE
FRESH AIR
TO BUILDING
EXHAUST AIR
TO OUTSIDE
DRAIN
CONNECTION
SERVICE CLEARANCE FROM
BOTTOM OF UNIT IS MINIMUM 3'0"
19”
ALL DUCT CONNECTION COLLARS ARE 5" DIAMETER
Option 2 - Reverse Duct Configuration Dimensions inches
FRESH AIR
FROM OUTSIDE
TOP VIEW
HANGING
STRAPS
EXHAUST AIR
FRESH AIR
EXHAUST AIR
TO OUTSIDE
FROM
FROM BUILDING
OUTSIDE
PLUG-IN CONNECTOR
FOR CONNECTING TO
REMOTE ELECTRICAL
BOX
EXHAUST
AIR FROM
FRESH AIR
BUILDING
TO BUILDING
EXHAUST AIR
TO OUTSIDE
FRESH AIR
TO BUILDING
DRAIN
CONNECTION
SERVICE CLEARANCE FROM
BOTTOM OF UNIT IS MINIMUM 3'0"
19”
ALL DUCT CONNECTION COLLARS ARE 5" DIAMETER
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Engineering Data
Model 120ERV
Latent Recovery/Moisture Transfer Core
Performance
The cross flow energy recovery core transfers heat and water vapor between the two air
streams. It is easily removed for cleaning and service.
Net supply air flow in cfm (L/s) against external static pressure
E.S.P
MOTORS AND BLOWERS
Each Air stream has an independent motorized impeller. 3 speed operation 120VAC.
(external static pressure)
[cfm (L/s)]
@ 0.1" (25 Pa)
@ 0.2" (50 Pa)
@ 0.3" (75 Pa)
@ 0.4" (100 Pa)
@ 0.5" (125 Pa)
@ 0.6" (150 Pa)
@ 0.7" (175 Pa)
@ 0.8" (200 Pa)
113 (53)
110 (52)
103 (49)
99 (47)
96 (45)
89 (42)
86 (41)
81 (38)
FILTERS
Washable air filters in exhaust and supply air streams.
MOUNTING THE ERV
Four threaded inserts at corners of case designed to accept four reinforced polyester straps
that are supplied with the unit.
CASE
Twenty gauge prepainted galvanized steel (G60) for superior corrosion resistance. Insulated
to prevent exterior condensation.
Cooling Mode @ 50 cfm (24 L/s) 95°F (35°C)
*Sensible Effectiveness
**Latent Transfer
62%
35%
44%
CONTROLS
Unit is supplied with a remote ERV box which can be conveniently located within 3’ of the
ERV.
Total Efficiency
Heating Mode @ 50 cfm (24 L/s) 32°F (0°C)
*Sensible Effectiveness
**Latent Transfer
ERV System Control
65%
38%
56%
ERV defaults to LOW SPEED when plugged in. HIGH SPEED option is accessible by con-
necting remote controls to designated terminals inside electrical box of ERV.
Total Efficiency
VAC @ 60HZ
120
63
Standard LOW SPEED SETTING can be increased to medium low. Off (Standby)/Low or
OFF/HIGH speed operation is also available.
WATTS / Low speed.
WATTS / High speed
Amp rating
150
1.5
DUCT CONNECTIONS
5” duct connections with ‘field’ selectable standard airflow or reverse airflow for limited room
installations.
*Sensible Efficiency - thermal **Latent Efficiency - moisture
WEIGHT 42 lbs. (19 kg) SHIPPING WEIGHT 45 lbs. (20.5 kg)
Note: Effectiveness - based on temp. differential between the 2 airstreams
Efficiency - takes into account all power inputs
OPTIONAL ACCESSORIES
99-132 20 Minute Fan Timer - initiates high speed ventilation for 20 minutes. (3 wire) 20
gauge wire (min.) 100’ length
140
3 - High Speed
2 - Medium Low Speed
1 - Low speed
99-101 Crank Timer
120
3
99-116 Dehumidistat Ventilation Control - Dehumidistat with ON/OFF
99-130 Dehumidistat Control - Dehumidistat
99-185 Weatherhoods, Two - 5” (125mm) c/w 1/4” (6mm) mesh screen
99-2040 20/40 ON/OFF Dehumidistat
100
80
2
60
1
WARRANTY
40
20
0
Units carry a lifetime warranty on the heat recovery core and a five year replacement parts
warranty.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
Static Pressure (in w.g.)
TOP VIEW
All units conform to CSA
and UL standards.
FRESH AIR
TO BUILDING
EXHAUST
AIR FROM
BUILDING
All Duct Collars are
5" diameter (127 mm)
FRESH AIR
FROM
OUTSIDE
EXHAUST AIR
TO OUTSIDE
SERVICE CLEARANCE FROM
BOTTOM OF UNIT IS MINIMUM 3'0"
19”
Date: ______________________________________________
Tag: ________________________ Qty: __________________
Project:_____________________________________________
Engineer: ___________________________________________
Contractor: __________________________________________
Supplier:____________________________________________
Quote#: ____________________________________________
Submitted by: ________________________________________
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Engineering Data
Model 120ERV
Option 1 - Duct Configuration Dimensions inches
EXHAUST AIR
FROM BUILDING
TOP VIEW
HANGING
STRAPS
FRESH AIR
TO BUILDING
EXHAUST
AIR FROM
BUILDING
FRESH AIR
FROM OUTSIDE
PLUG-IN CONNECTOR
FOR CONNECTING TO
REMOTE ELECTRICAL
BOX
FRESH AIR
FROM
OUTSIDE
EXHAUST AIR
TO OUTSIDE
FRESH AIR
TO BUILDING
EXHAUST AIR
TO OUTSIDE
SERVICE CLEARANCE FROM
BOTTOM OF UNIT IS MINIMUM 3'0"
19”
ALL DUCT CONNECTION COLLARS ARE 5" DIAMETER
Option 2 - Duct Configuration Dimensions inches
FRESH AIR
FROM OUTSIDE
TOP VIEW
HANGING
STRAPS
EXHAUST AIR
TO OUTSIDE
FRESH AIR
EXHAUST AIR
FROM BUILDING
FROM
OUTSIDE
PLUG-IN CONNECTOR
FOR CONNECTING TO
REMOTE ELECTRICAL
BOX
EXHAUST
AIR FROM
BUILDING
FRESH AIR
TO BUILDING
EXHAUST AIR
TO OUTSIDE
FRESH AIR
TO BUILDING
SERVICE CLEARANCE FROM
BOTTOM OF UNIT IS MINIMUM 3'0"
19”
ALL DUCT CONNECTION COLLARS ARE 5" DIAMETER
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
The RNC120F model can be setup in two different airflow
configurations as illustrated in the engineering data sec-
tion of the manual. Because of this, it is extremely
important that the unit be connected properly. The remote
electrical control box contains two receptacles labelled
“Fan Connection A” and “Fan Connection B”. It is critical
that the proper fan be plugged into the proper recepta-
cle.
FRESH AIR
FROM OUTSIDE
EXHAUST AIR
FROM BUILDING
EXHAUST AIR
TO OUTSIDE
FRESH AIR
TO BUILDING
DRAIN
CONNECTION
EXHAUST AIR
FROM BUILDING
FRESH AIR
FROM OUTSIDE
FRESH AIR
TO BUILDING
EXHAUST AIR
TO OUTSIDE
DRAIN
CONNECTION
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearances and Requirements
Connecting Appliances to the HRV
The following appliances should not be connected to the
HRV:
WARNING
Before installation, careful consideration must
be given to how this system will operate if
connected to any other piece of mechanical
equipment, i.e. a forced air furnace or air handler,
operating at a higher static. After installation, the
compatibility of the two pieces of equipment
must be confirmed, by measuring the air flows of
the ventilator, by using the balancing procedure
found in this manual.
• clothes dryer
• range top
• stovetop fan
• central vacuum system
CAUTION
Lint, dust or grease will collect in the HRV
damaging the unit.
It is always important to assess how the operation
of any HRV may interact with vented combustion
equipment (i.e. Gas Furnaces, Oil Furnaces,
Wood Stoves, etc.)
NOTE: Connecting any of these to the HRV will
invalidate your warranty.
NEVER install a ventilator in a situation where its
normal operation, lack of operation or partial
failure may result in the backdrafting or improper
functioning of vented combustion equipment!
Installation
The HRV unit must be installed in a horizontal position as
shown in the illustration below. The unit should be sus-
pended using the provided hanging straps. The unit must
be level for proper condensate drainage. Sufficient
clearance below the access door is required for servicing
the air filters and core. A minimum of 25" (635mm) clear-
ance is recommended so the door can be removed. Four
PVC reinforced polyester hanging straps are provided for
hanging the HRV.
WARNING
Improper installation, adjustment, alteration,
service or maintenance can cause property
damage, personal injury or loss of life.
Installation and service must be performed by a
qualified installer or service agency.
Suspending the Unit
WARNING
The hanging straps should be attached to the unit at the
top end corners (mounting screws are already located on
the HRV case). Securely fasten the other end of the straps
to the ceiling making sure the UNIT IS LEVEL. The straps
are designed to reduce the possibility of noise, resonance
or harmonics; therefore using the full length of the strap
between the HRV and the floor joists is recommended.
Electric shock hazard. Can cause
injury or death. Before attempting to
perform any service or maintenance,
turn the electrical power to unit OFF
at disconnect switch(es). Unit may
have multiple power supplies.
Weatherhood Location and Installation
Weatherhood kit includes two fixed-cover hoods with a
1/4” (6mm) mesh screen.
Location Selection
The HRV must be located in a heated space where it will
be possible to conveniently service the unit. Typically the
HRV would be located in the mechanical room or an area
close to the outside wall where the weather hoods will be
mounted. If a basement area is not convenient or does not
exist, a utility or laundry room may be used.
Exhaust Weatherhood Requirements
•
•
At least 6' (2 m) from the ventilation air intake*
At least 18" (460mm) above ground or above the
depth of expected snow accumulation*
Attic installations are not normally recommended due to:
A) the complexity of work to install
•
•
At least 3' (1 m) away from the corner of the building*
At least 3’ away from gas meter, electric meter or a
walkway where fog or ice could create a hazard*
B) freezing conditions in the attic
•
Not into a garage, workshop or other unheated space
C) difficulty of access for service and cleaning
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Suspending the Unit using the
Provided Hanging Straps
CAUTION
Unit must be installed level to ensure proper
condensate drainage. Due to the broad range of
installation and operational conditions,
consideration must be given for the possibility
of condensation forming on the unit or
FASTENERS
(not supplied)
connecting ducting.
Objects below the
installation may be exposed to condensate.
STRAPS
AND
SCREWS
(supplied)
When installing the weather hood, its outside perimeter
must be sealed with exterior caulking.
DETAIL
Unit is designed for
horizontal installation
only as shown.
* Local code may require greater distances.
Intake Weatherhood Requirements
• Should be located upstream (if there are prevailing
winds) from the exhaust outlet
Using full length hanger
straps is recommended
for vibration control, but
can be shorter if required.
• At least 6' (2 m) from the exhaust weather hood *
• At least 6' (2 m) away from dryer vents and air handler
exhaust (medium or high efficiency furnaces)*
Note: Illustration depicts unit suspended from wood floor joists. If
a different ceiling system is used, securing straps to floor will be
different.
• A minimum of at least 6' (2 m) from driveways, oil fill
pipes, gas meters, or garbage containers, swimming
pools*
• At least 18" (460mm) above the ground, or above the
depth of expected snow accumulation*
Weatherhood Installation
COLLARꢀISꢀSUPPLIEDꢀTOꢀ
ENSUREꢀVAPOURꢀBARRIERꢀ
ISꢀ100%ꢀSEALEDꢀTOꢀ
WALLꢀPLATE
SCREEN
(sideꢀview)
• At least 3' (1 m) from the inside/outside corner of the
building*
• Do not locate in a garage, attic or crawl space
12"ꢀgalvanized
pipeꢀsupplied
* Local code may require greater distances.
EXTERIORꢀ
WALL
1/4"ꢀ(6ꢀmm)ꢀSCREEN
(frontꢀview)
1.ꢀ ThermalꢀCollarꢀslidesꢀoverꢀgalvanizedꢀ
sleeveꢀofꢀWeatherhood.
2.ꢀ FastenꢀThermalꢀCollarꢀtoꢀBelt.
3.ꢀ SlideꢀtheꢀInsulatedꢀFlexibleꢀDuctingꢀoverꢀ
theꢀWeatherhood'sꢀgalvanizedꢀsleeveꢀandꢀ
fastenꢀitꢀtoꢀtheꢀThermalꢀCollar.
4.ꢀ Hoodꢀisꢀhingedꢀtoꢀallowꢀforꢀeasyꢀaccessꢀ
ꢀꢀ forꢀcleaningꢀofꢀbirdꢀscreen.
Weatherhood Clearances
OUTSIDE CORNER
INSIDE CORNER
36" (1m)
36" (1m)
recommended min.
recommended min.
CAUTION
Weather hood arrangement - requires a minimum
of 6’ (2m) separation and a minimum of 18" (460mm)
clearance above grade or anticipated snow level.
6' (2m)
recommended min.
EXHAUST
INTAKE
18" (460mm) min.
18" (460mm) min.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Air Duct Design and Installation
A well designed and installed ducting system will allow the
HRV to operate at its maximum efficiency.
WARNING
Include a short length of fabric, flex duct or
other non-metallic connector in the “Fresh Air to
Building” hard ducted line in order to keep the
HRV separately grounded (electrically) from the
air handler. This will avoid a possible shock
hazard to service people if a short to ground
develops in one of the devices.
Always try to keep duct runs as short and straight as pos-
sible. See Installation Diagrams for various installation
options.
The inner and outer liners of the flexible insulated duct
must be clamped to the sleeve of the weather hoods (as
close to the outside as possible) and the appropriate port
on the HRV. It is very important that the fresh air intake
line be given special attention to make sure it is well
sealed. A good bead of high quality caulking (preferably
Grilles that diffuse the air comfortably such as the Round
Diffuser are recommended.
If the floor is the only option available, then special care
should be taken in locating grilles. Areas such as under
baseboard heaters will help to temper the air. Also option-
al inline duct heaters are available for mounting in the
supply duct work to add heat if required.
silicone sealant) will seal the inner flexible duct to both the
HRV port and the weather hood prior to clamping with a
large zip tie.
To minimize air flow restriction, the flexible insulated duct
that connects the two outside weather hoods to the HRV
should be stretched tightly and be as short as possible.
Direct Connection to Air Handler Duct System
Should you wish to hard duct the fresh air from the HRV
directly into the cold air return of the air handler, remem-
ber to check the air flow balance of the HRV with the air
handler fan both "ON" and "OFF" to determine that it does
not imbalance the unit more than 10%.
Twisting or folding the duct will severely restrict air flow.
See below for the recommended connection of flexible
insulated ducts to the the outside weather hoods and the
HRV.
Installing the Ducting Between
Indirect Connection to Air Handler Duct System
If permitted by local codes, an indirect connection may be
made between the HRV fresh air duct and the air handler
return plenum. The fresh air from the unit may be directed
at a grille installed in the cold air return duct of the air han-
dler. The fresh air outlet from the HRV should be no closer
than 4 inches (100mm) and no more than 12 inches
(300mm) from the grille.
the HRV & Living Areas in the Home
To maximize airflow in the duct system, all ducts should
be kept short and have as few bends or elbows as possi-
ble. Forty-five degree elbows are preferred to 90° elbows.
Use “Y” tees instead of 90° elbows whenever possible.
All duct joints must be fastened with screws, rivets or duct
sealant and wrapped with mastic or a quality duct tape to
prevent leakage. Mastic is preferred but if duct tape is
used, we recommend aluminum foil duct tape.
Galvanized ducting from the HRV to the living areas in the
house is recommended whenever possible, although flexi-
ble duct can be used in moderation if necessary.
FRESH AIR
FROM HRV
To avoid possible noise transfer through the duct system,
a short length (approximately 12 inches or 300mm) of non-
metallic flexible insulated duct should be connected
between the HRV and the supply/exhaust duct system.
4" MINIMUM
12" MAXIMUM
RETURN AIR
DUCT FOR
AIR HANDLER
V
HR
The main supply and return lines to/from the HRV must be
the same size or larger than the duct connection collar.
Branch lines to the individual rooms may be as small as 4
inches (100mm), but 5 inch (125mm) lines are preferred .
All ducts running through attics and unheated spaces must
be sealed and insulated to code.
Fresh Air Ducting
In applications that do not include an air handler, fresh air
should be supplied to all bedrooms and living areas,
excluding bathrooms, kitchen and utility areas. Grilles
should be located high on a wall or in ceiling locations.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Stale Air Exhaust System
Drain Connection (HRV Only)
The stale air exhaust system draws air from the points in
the house where the worst air quality problems occur.
Stale air ducts should be installed in the bathroom,
kitchen, and laundry room. Applications such as green-
houses, atriums, swimming pools, saunas, etc. have
unique ventilation requirements which should be
addressed with an isolated ventilation system. Also, the air
handler return duct may be used to exhaust from. In this
method, the exhaust air is not ducted back to the HRV
with "dedicated lines" from bathrooms, kitchens, etc.
Instead, the exhaust air is drawn out of the cold air return
of the air handler. The air handler blower must be run-
ning when the unit is operating for this system to be
effective.
During a defrost cycle, the HRV may produce some con-
densation. This water should flow into a nearby drain, or
be taken away by a condensate pump.
CAUTION
The HRV and all condensate lines must be
installed in a space where the temperature is
maintained above the freezing point.
The HRV has a condensate pan and drain spout built into
the door. Construct a P-Trap by creating a loop in the
drain. This creates a “trap” which will hold some conden-
sate and prevent odours from being drawn up the hose
and into the fresh air supply of the HRV.
CAUTION
"P" Trap (HRV only)
Balancing Dampers and Grilles
Balancing dampers and/or adjustable grilles should be
used to balance the flow rates into and out of various
rooms.
Grilles or diffusers should be positioned high on the wall or
in the ceiling. Kitchen exhaust grilles must never be con-
nected to a range hood. They should be installed at least 4
feet (1.2m) horizontally away from the stove. A hinged
6”X10” (150 X 250mm) rectangular kitchen exhaust grille
is available. This grille includes a removable grease filter.
Canadian building codes require that kitchen grilles be
equipped with washable filters.
CAUTION
Field-supplied balancing dampers should be installed
external to the unit to balance the amount of stale air
being exhausted with the amount of fresh air being
brought into the house. Refer to Air flow Balancing sec-
tion.
Drain trap and tubing MUST be below bottom of
door with 1/4" per foot downwards slope away
from unit.
Note: Secondary drain pan may be required to
protect from condensate leakage.
Kitchen Grille
REMOVABLE
FILTER
The Round
Diffuser is available in
4" (100mm)
5” (125mm)
6" (150mm)
8" (200mm)
AIR FLOW
AIR FLOW
EXHAUST
SUPPLY
Round
Diffusers
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Illustrations
HRV–Option 1
Partially Dedicated System for HRV
●
Stale air drawn from key areas of
home (bathroom, kitchen, laundry)
WARNING
HRV must be balanced.
●
Fresh air supplied to return
air duct of air handler
DIRECT CONNECTION of the SUPPLY AIR STREAM to the AIR HANDLER COLD AIR RETURN
(Stale air drawn from key areas of home)
Outdoors
Exhaust Air to Outside
Return Air
STALE AIR from various parts of home.
3’ min.
recommended
i.e. bathrooms (if required), kitchens (if required).
Field-supplied
Balancing Damper
(optional)
Fresh Air to Building
Fresh Air From Outside
Cool Air
Return
*Unit is normally balanced on HIGH speed
with air handler blower ON.
Air
Handler
High efficiency filter
or electronic air cleaner
NOTES:
1. Air handler blower may be required to operate when HRV is on to provide good air distribution.
2. Weather hood arrangement is for drawing purposes only. 6' (2m) minimum separation required.
18" (460mm) above grade minimum or above anticipated snow level .
3. Due to the differences in pressure between the HRV and the equipment it is being
connected to, the HRV air flow must be confirmed on site, using the balancing
procedure found in the installation manual.
WARNING
Defrost air port needs to be drawn from clean
area without combustion appliances. To avoid
backdrafting of combustion products, never
draw defrost air from a room with a naturally
aspirated appliance, i.e. furnace, hot water
heater, gas dryer, stove, fire place etc.
CAUTION
Weather hood arrangement - requires a minimum
of 6' (2m) separation and a minimum of 18" (460mm)
clearance above grade or anticipated snow level.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Illustrations
HRV–Option 1
Simplified Installation for HRV
(Return/Return Method)
•
•
It is mandatory that the air handler blower
run continuously or HRV operation be
interlocked with the air handler blower.
WARNING
HRV must be balanced.
Check local codes/authority having
jurisdiction for acceptance.
DIRECT CONNECTION of both the HRV SUPPLY AIR STREAM and
EXHAUST AIR STREAM to the AIR HANDLER COLD AIR RETURN
Outdoors
*Unit is normally balanced on
HIGH speed with air handler
blower ON.
Exhaust Air to Outside
Return Air
40" (1m) MINIMUM
Field-supplied Balancing Damper (optional)
3' (915 mm) min.
recommended
Fresh Air to Building
Fresh Air From Outside
Cool Air
Return
Air
Handler
NOTES:
1. Air handler blower must operate when ventilation from HRV is required.
The air handler should be set to run continuously or interlocked with HRV.
2. A minimum separation of 40 inches (1m) is required between the two direct connections.
3. The exhaust air connection should be upstream of the supply air connection to prevent
exhausting any fresh air.
4. Weather hood arrangement is for drawing purposes only. Six feet (2m) minimum separation required.
18" inches (460mm) above grade minimum or above anticipated snow level.
5. Due to the differences in pressure between the HRV and the equipment it is being
connected to, the HRV's air flow must be confirmed on site, using the balancing
procedure found in the installation manual.
High efficiency filter
or electronic air cleaner
WARNING
Defrost air port needs to be drawn from clean
area without combustion appliances. To avoid
backdrafting of combustion products, never
draw defrost air from a room with a naturally
aspirated appliance, i.e. furnace, hot water
heater, gas dryer, stove, fire place etc.
CAUTION
Weather hood arrangement - requires a minimum
of 6' (2m) separation and a minimum of 18" (460mm)
clearance above grade or anticipated snow level.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Illustrations
HRV–Option 1
Fully Dedicated System for HRV
●
Stale air drawn from key areas of
home (bathroom, kitchen, laundry)
WARNING
HRV must be balanced.
●
Fresh air supplied to main living
areas of home
Outdoors
Exhaust Air To Outside
STALE AIR from
various parts of home.
i.e. bathrooms
(if required),
Field-supplied Balancing Damper (optional)
kitchens
(if required).
Fresh air to house -
main living areas...
Fresh Air From Outside
bedrooms, living room,
rec. room etc.
*Unit is normally balanced on HIGH speed
with air handler blower ON.
NOTES:
1. Weather hood arrangement is for drawing purposes only. 6' (2m) minimum separation required.
18" (460mm) above grade minimum or above anticipated snow level .
2. The HRV air flow must be confirmed on site, using the balancing procedure found in the installation manual.
WARNING
Defrost air port needs to be drawn from clean
area without combustion appliances. To avoid
backdrafting of combustion products, never
draw defrost air from a room with a naturally
aspirated appliance, i.e. furnace, hot water
heater, gas dryer, stove, fire place etc.
CAUTION
Weather hood arrangement - requires a minimum
of 6' (2m) separation and a minimum of 18" (460mm)
clearance above grade or anticipated snow level.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Illustrations
HRV–Option 2
Partially Dedicated System for HRV
●
Stale air drawn from key areas of
home (bathroom, kitchen, laundry)
WARNING
HRV must be balanced.
●
Fresh air supplied to return
air duct of air handler
DIRECT CONNECTION of the SUPPLY AIR STREAM to the AIR HANDLER COLD AIR RETURN
(Stale air drawn from key areas of home)
Outdoors
Exhaust Air to Outside
Return Air
3’ min.
recommended
Fresh Air From Outside
Fresh Air to Building
Cool Air
Return
STALE AIR from various parts of home.
i.e. bathrooms (if required), kitchens (if required).
Field-supplied
Balancing Damper
(optional)
*Unit is normally balanced on HIGH speed
with air handler blower ON.
High efficiency filter
or electronic air cleaner
NOTES:
1. Air handler blower may be required to operate when HRV is on to provide good air distribution.
2. Weather hood arrangement is for drawing purposes only. 6' (2m) minimum separation required.
18" (460mm) above grade minimum or above anticipated snow level .
3. Due to the differences in pressure between the HRV and the equipment it is being
connected to, the HRV air flow must be confirmed on site, using the balancing
procedure found in the installation manual.
WARNING
Defrost air port needs to be drawn from clean
area without combustion appliances. To avoid
backdrafting of combustion products, never
draw defrost air from a room with a naturally
aspirated appliance, i.e. furnace, hot water
heater, gas dryer, stove, fire place etc.
CAUTION
Weather hood arrangement - requires a minimum
of 6' (2m) separation and a minimum of 18" (460mm)
clearance above grade or anticipated snow level.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Illustrations
HRV–Option 2
Simplified Installation for HRV
(Return/Return Method)
●
It is mandatory that the air handler blower
run continuously or HRV operation be
interlocked with the air handler blower.
WARNING
HRV must be balanced.
●
Check local codes/authority having
jurisdiction for acceptance.
DIRECT CONNECTION of both the HRV SUPPLY AIR STREAM and
EXHAUST AIR STREAM to the AIR HANDLER COLD AIR RETURN
Return Air
*Unit is normally balanced on
HIGH speed with air handler
blower ON.
3’ (915 mm) min.
recommended
40" (1m) MINIMUM
Outdoors
Exhaust Air to Outside
Fresh Air From Outside
Fresh Air to Building
Field-supplied Balancing Damper (optional)
Cool Air
Return
Air
Handler
NOTES:
1. Air handler blower must operate when ventilation from HRV is required.
The air handler should be set to run continuously or interlocked with HRV.
2. A minimum separation of 40 inches (1m) is required between the two direct connections.
3. The exhaust air connection should be upstream of the supply air connection to prevent
exhausting any fresh air.
4. Weather hood arrangement is for drawing purposes only. Six feet (2m) minimum separation required.
18" inches (460mm) above grade minimum or above anticipated snow level.
5. Due to the differences in pressure between the HRV and the equipment it is being
connected to, the HRV's air flow must be confirmed on site, using the balancing
procedure found in the installation manual.
High efficiency filter
or electronic air cleaner
WARNING
Defrost air port needs to be drawn from clean
area without combustion appliances. To avoid
backdrafting of combustion products, never
draw defrost air from a room with a naturally
aspirated appliance, i.e. furnace, hot water
heater, gas dryer, stove, fire place etc.
CAUTION
Weather hood arrangement - requires a minimum
of 6' (2m) separation and a minimum of 18" (460mm)
clearance above grade or anticipated snow level.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Illustrations
HRV–Option 2
Fully Dedicated System for HRV
●
Stale air drawn from key areas of
home (bathroom, kitchen, laundry)
WARNING
HRV must be balanced.
●
Fresh air supplied to main living
areas of home
Outdoors
Exhaust Air To Outside
Fresh air to house -
main living areas...
bedrooms, living room,
rec. room etc.
Fresh Air From Outside
STALE AIR from
various parts of home.
i.e. bathrooms
(if required),
Field-supplied Balancing Damper (optional)
kitchens
(if required).
*Unit is normally balanced on HIGH speed
with air handler blower ON.
NOTES:
1. Weather hood arrangement is for drawing purposes only. 6' (2m) minimum separation required.
18" (460mm) above grade minimum or above anticipated snow level .
2. The HRV air flow must be confirmed on site, using the balancing procedure found in the installation manual.
WARNING
Defrost air port needs to be drawn from clean
area without combustion appliances. To avoid
backdrafting of combustion products, never
draw defrost air from a room with a naturally
aspirated appliance, i.e. furnace, hot water
heater, gas dryer, stove, fire place etc.
CAUTION
Weather hood arrangement - requires a minimum
of 6' (2m) separation and a minimum of 18" (460mm)
clearance above grade or anticipated snow level.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Devices
Optional Main Controls
The Dehumidstat Dial
The amount of ventilation required in your home will fluctuate
according to the activity level in the house. Higher activity levels
require more ventilation.
Main controls feature a dehumidistat dial. The dehumidistat is
used to reduce high winter humidity levels. The dehumidistat
activates high speed ventilation when the indoor humidity level
exceeds selected setting.
Main controls can be mounted in a central location of the home
(i.e. beside the furnace thermostat) which will provide the user
with complete control over their ventilation system from a conve-
nient location.
ATTENTION
The ON/OFF Switch
Only one main control can be installed on your
system.
The ON/OFF Switch will turn the HRV ON or OFF. Controls with
an ON/OFF switch can be modified to ON/Standby by adjusting
the circuit board DIP Switches (Refer to "Mode DIP Switch
Settings").
Ventilation Dehumidistat
PART NO. 99-116
Remote Dehumidistat
PART NO. 99-130 White
The Remote Dehumidistat activates high speed ventilation when
the indoor humidity level exceeds the set point.
The High/Low Speed Switch initiates High or Low speed ventila-
tion. This control also has an ON/OFF Switch and a
Dehumidistat Dial (refer to "The ON/OFF Switch" and "The
Dehumidistat Dial" descriptions).
Dehumidistat
Dial
High/Low
Speed Switch
T
A
ꢀꢀDEHUMIDIST
Dehumidistat
Dial
ON/OFF
Switch
20/40 ON/OFF Dehumidistat
PART NO. 99-2040
The 20/40 Switch will toggle from continuous low speed ventila-
tion to an intermittent mode of 20 minutes fan ON (in low speed)
and 40 minutes fan OFF. The Dehumidistat Dial will initiate High
Speed ventilation when the indoor humidity level exceeds the set
point (regardless position of the 20/40 Switch.). This control also
has an ON/OFF Switch (refer to "The ON/OFF Switch" descrip-
tion).
Dehumidistat
Dial
20/40
Switch
ON/OFF
Switch
ꢀ
Timer is the best selection, however, the crank timer will be nec-
essary if only 2 lead low voltage wires are present.
Optional Timers
Timers should be present when the HRV is exhausting from
specific locations i.e bathrooms, laundry rooms. The 20 Minute
Crank Timer
PART NO. 99-101
20 Minute Timer
PART NO. 99-132
Off
10
20
Connects to RED and BLACK termi-
Connects to RED, BLACK and GREEN
(LED drive) terminals. Use a minimum of
three 20 gauge low voltage wire. Connect
up to 4 on 100 ft (91 m) wire max. Mounts
in a 2 x 4 box.
nals. Use a two 18 gauge low
voltage wire. Mounts in a 2 x 4 box.
The crank timer provides a solution
to installing a system where only 2
wires are present for the timers.
30
60
40
50
Crank Dial
Touch Pad
The Touch Pad initi-
ates high speed
Rotate the dial for up to 60
minutes high speed opera-
tion.
20 Minute Status Lights
The 20 Minute Status Light indicates
high speed operation is activated.
operation.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring the Controls
2040 ON/OFF Dehumidistat
Dehumidistat Ventilation Control
Part No. 99-2040
Part No. 99-116
Red to Red
Red to Red
Orange to
Orange
Black to
Black
Remove
factory
installed
jumper when
installing this
control
Remove
factory
installed
jumper when
installing this
control
Orange to
Orange
T
A
UMIDIST
DEH
Black to Black
Low Fan
to Blue
Circuit Board
Circuit Board
Terminal Strip
Remote Dehumidistat
Part No. 99-130W
Red to Red
Factory
installed
jumper
Black to Black
Circuit Board
Terminal Strip
Circuit Board
Terminal Strip
20 Minute Timer
Crank Timer
(shown in a Decora cover plate)*
Part No. 99-101
Red to Red
Red to Red
Factory
installed
jumper
Factory
installed
jumper
Black to
Black
Black to
Black
Off
10
20
30
Green LED
Drive to Green
60
40
50
Circuit Board
ATTENTION
Controls will use 2, 3 or 4 lead 20 gauge wire. Note
the number of leads required for each control (refer
to the above illustrations).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical
The HRV unit should be plugged into a standard designat-
ed (120VAC) electrical outlet with a ground. The outlet
should be serviced by a separate 15 amp/120V circuit. An
extension cord should not be used with this appliance. A
qualified service technician should make any required
electrical connections.
WARNING
In order to prevent electric shock when cleaning
or servicing the HRV, it is extremely important to
confirm the polarity of the power line that is
switched by the safety (disconnect) switch. The
hot line (black) is the proper line to be switched.
To confirm the proper polarity, use a voltmeter
or test lamp to ensure there is no power after
the switch when the door is open. Check
between that point and ground (on the cabinet).
Always make sure that the HRV is properly
grounded.
Remote Control Connections
Prior to connecting remote devices, it is advisable to
run self test on the HRV/ERV.
Low voltage connections between the remote controls, the
dehumidistat, or the fan timer should be made by a quali-
fied service technician. Low voltage wires from the remote
controls are connected to the HRV micro-processor board.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
For most installations the HRV will normally be set to oper-
ate continuously on low speed. To suit various lifestyles,
the HRV offers a selection of operating modes.
Self Test
The ventilator will automatically initiate a self test
sequence when power is applied. Fan motor is cycled and
then damper motor is cycled. Duration: Approximately 1.5
mins.
Method of Operation
Good -
intermittent operation at all times
How much ventilation do I need?
Better-
continuous operation during day or occupied
conditions, intermittent at night or unoccupied
During seasons when your windows and doors are closed
(winter and summer if air conditioned) the HRV should
operate continuously when the dwelling is occupied, and
either continuously or intermittently when not occupied.
Best -
recommended continuous operation of both
HRV and furnace/air handler blower
Mode DIP Switch Settings
Figure 1 - Factory DIP Switch Settings
The factory setting of the DIP switches (located on the cir-
cuit board) provides continuous low speed ventilation.
Optional Remote Controls will initiate high speed ventila-
tion.
Figure 2-DIP Switch Settings for Standby (When
using a Remote Control Device that has an
ON/OFF Switch)
This DIP Switch Setting can be adjusted when using a
system control that has an ON/OFF switch (refer to
"Remote Control Devices" in this manual). "STANDBY" is
achieved when the Remote Control Switch is in the "OFF"
position. The Dehumidistat and Timers will initiate high
speed ventilation regardless of the "ON/OFF" switch posi-
tion when this DIP switch configuration is used.
Remote controls with an ON/OFF switch (refer to "Remote
Control Devices" in this manual) will shut the entire sys-
tem down when the remote control is in the OFF position.
Changing the remote control from OFF to STANDBY can
be achieved by Setting the DIP Switch as per Figure 2.
ON
Figure 2
Figure 1
ON
HS
REMOTE
DFR2
HS
REMOTE
DFR2
DFR3
DFR3
ATTENTION
Figure 2 may not meet building code conformance
in certain geographical areas. Check with your
local building authority.
Increasing Low Speed to Medium Low
The ventilator automatically operates on its lowest speed
when plugged in or switched on. This setting is factory
supplied from an autotransformer with two selectable low
speeds. To switch to a continuous medium low speed, an
installing contractor must interchange the red and blue
wires from the autotransformer inside the electrical box.
Whether or not this change is made, the HRV will only be
able to access a single selected low speed.
High speed is available with the use of optional remote
controls connected to the appropriate terminals inside the
electrical box.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagrams
HRV CONTROL BOX
FAN A
FAN B
FAN A
FAN B
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Interlocking HRV Operation to an Airhandler/Furnace Blower
When using the Interface relay contacts to initiate blower operation on a fur-
nace, certain thermostats will initiate the outdoor cooling condenser when
R and G are closed.
Use this wiring configuration to prevent the Interface relay contacts from initializing
the condenser unit. This problem can occur at the thermostat because the Y termi-
nal is connected to the G terminal internal to the stat. When R and G are closed at
the furnace (by dehumidistat or relay) 24 Volts is sent to G at thermostat. 24 Volts is
then sent through Y which will initiate outdoor condenser.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Dehumidistat Operation (HRV only)
The optional HRV remote controls include a dehumidistat
which controls humidity levels during the heating season.
The control has a selector knob with set points ranging
from 20% to 80% relative humidity (RH). Most people are
comfortable when indoor relative humidity levels are in a
range from 30 to 45%.
The dehumidistat switches the ventilator to high speed
when the moisture level in the building exceeds the
desired setpoint. The dehumidistat switches the HRV back
to low speed ventilation when the humidity has been
reduced below the setpoint. The dehumidistat should
only be used during the heating season. It must be set
to OFF position throughout the rest of the year.
Defrost Operation
The fan defrost HRV is equipped with an electronically
controlled fan defrost system to remove frost that collects
on the warm air side of the aluminum heat transfer sur-
faces of the heat exchanger core. When the outside air
temperature drops below 27°F (3°C), defrost is activated
which provides for an automatic defrost cycle. During the
automatic defrost cycle, the fresh air supply is shut off
while the exhaust fan continues to operate. This allows the
warm inside air to flow through the heat exchanger core
melting frost accumulation. After the defrost period, the
fresh air supply fan returns to the normal speed and fresh
outside air continues to be drawn into the building. Water
from the melted frost collects in the bottom of the drip
pans and drains out through the bottom drain connections.
The defrost cycle repeats automatically until the air tem-
perature rises above 27°F (-3°C).
Defrost Cycle DIP Switch Settings
Defrost DIP Switch Settings (located on the circuit board)
can be adjusted to increase the unit’s run (ventilation)
time. The three minute defrost time cannot change.
Factory Setting
3 minute defrost time
17 minute run time
Option 1*
3 minute defrost time
25 minute run time
Option 2*
3 minute defrost time
30 minute run time
ON
ON
ON
HS
HS
HS
REMOTE
DFR2
REMOTE
DFR2
REMOTE
DFR2
DFR3
OFF
ON
DFR3
DFR3
OFF
ON
SW1
SW1
SW1
*Lengthening the run time may result in ice build-up on the core.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Flow Balancing
It is necessary to have balanced air flow in an HRV. The volume of air
brought in from the outside must equal the volume of air exhausted by
the unit. If the air flow is not properly balanced, then:
The first step is to operate all mechanical systems on high speed, which
have an influence on the ventilation system, i.e. the HRV itself and the air
handler, if applicable. This will provide the maximum pressure that the
HRV will need to overcome, and allow for a more accurate balance of the
unit.
•
•
•
•
The HRV may not operate at its maximum efficiency
A negative or positive air pressure may occur in the house
The unit may not defrost properly
Drill a small hole in the duct (about 3/16"), three feet downstream of any
elbows or bends, and one foot upstream of any elbows or bends. These
are recommended distances but the actual installation may limit the
amount of straight duct.
Failure to balance HRV properly may void warranty
The Pitot tube should be connected to a magnehelic gauge or digital
manometer capable of reading from 0 to 0.25 in. (0-62 Pa) of water,
preferably to 3 digits of resolution. The tube coming out of the end of the
Pitot is connected to the high pressure side of the gauge. The tube com-
ing out of the branch of the Pitot is connected to the low pressure or
reference side of the gauge.
CAUTION
Ensure balanced air flow in HRV. Excessive
positive pressure may drive moist indoor air into
the external walls of the building where it may
condense (in cold weather) and degrade
structural components. May also cause key
holes to freeze up.
Insert the Pitot tube into the duct; pointing the tip into the air flow.
For general balancing it is sufficient to move the Pitot tube around in the
duct and take an average or typical reading. Repeat this procedure in the
other (supply or return) duct. Determine which duct has the highest air
flow (highest reading on the gauge). Then damper that air flow back to
match the lower reading from the other duct. The flow should now be
balanced.
Excessive negative pressure may have several undesirable effects. In
some geographic locations, soil gases such as methane and radon gas
may be drawn into the home through basement/ground contact areas.
Actual air flow can be determined from the gauge reading. The value read
on the gauge is called the velocity pressure. The Pitot tube comes with a
chart that will give the air flow velocity based on the velocity pressure
indicated by the gauge. This velocity will be in either feet per minute or
meters per second. To determine the actual air flow, the velocity is multi-
plied by the cross sectional area of the duct being measured.
Read the Application Warning in Clearances & Requirements section
of this manual!
This is an example for determining the air flow in a 6" duct.
The Pitot tube reading was 0.025 inches of water.
From the chart, this is 640 feet per minute.
WARNING
Ensure balanced air flow in HRV. Excessive
negative pressure may also cause the back-
drafting of vented combustion equipment.
The 6" duct has a cross sectional area of
= [3.14 x (6"÷12)2]÷4
= 0.2 square feet
Prior to balancing, ensure that:
1. All sealing of the duct system has been completed.
The air flow is then:
2. All of the HRV’s components are in place and
640 ft./min. x 0.2 square feet = 128 cfm
functioning properly.
For your convenience, the cross sectional area of some common round
duct is listed below:
3. Balancing dampers are fully open.
4. Unit is on HIGH speed.
DUCT DIAM. (inches)
CROSS SECTION AREA (sq. ft.)
5. Air flow in branch lines to specific areas of the house should be
adjusted first prior to balancing the unit. A smoke pencil used at the
grilles is a good indicator of each branch line's relative air flow.
5
6
7
0.14
0.20
0.27
6. After taking readings of both the stale air to the HRV duct and fresh
air to the house duct, the duct with the lower CFM ([L/s] velocity)
reading should be left alone, while the duct with the higher reading
should be dampered back to match the lower reading.
The accuracy of the air flow reading will be affected by how close to any
elbows or bends the readings are taken. Accuracy can be increased by
taking an average of multiple readings as outlined in the literature sup-
plied with the Pitot tube.
7. Return unit to appropriate fan speed for normal operation
8. A field-supplied balancing damper for the stale air side is required for
system balancing.
Balancing Procedure
The following is a method of field balancing an HRV using a Pitot tube,
which is advantageous in situations when flow stations are not installed
in the duct system. Procedure should be performed with the HRV on
high speed.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Flow Balancing
Pitot Tube and Gauge
Pitot Tube Air Flow
Balancing Kit
with magnehelic gauge,
Pitot tube, hose and
carry case.
DUCT
AIR
FLOW
Pitot tube
Magnehelic gauge
High Pressure Side
Low Pressure Side
Placement of Pitot Tube HRV
NOTE: Graphic is for illustrative purposes only.
Duct connection ports may vary.
NOTE: Apply use of balancing dampers as required.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Symptom
Cause
Solution
• 1/4” (6mm) mesh on the outside hoods is plugged
• filters plugged
• clean exterior hoods or vents
• remove and clean filter
Poor Air Flow
• core obstructed
• remove and clean core
• house grilles closed or blocked
• dampers are closed if installed
• poor power supply at site
• check and open grilles
• open and adjust dampers
• have electrician check supply voltage at house
• check duct installation
• duct is restricting HRV
• improper speed control setting
• HRV air flow improperly balanced
• increase the speed of the HRV
• have contractor balance HRV
• poor location of supply grilles, the air flow may irritate • locate the grilles high on the walls or under the baseboards,
Supply air feels cold
the occupant
install ceiling mounted diffuser or grilles so as not to directly
spill the supply air on the occupant (eg. over a sofa)
• turn down the HRV supply speed. A small duct heater (1kw)
could be used to temper the supply air
• outdoor temperature extremely cold
• placement of furniture or closed doors is restricting themove-
ment of air in the home
• if supply air is ducted into air handler return, the air handler fan
may need to run continuously to distribute ventilation air com-
fortably
• improper connection to ventilator
• external low voltage is shortened out by a staple or nail
• check dehumidistat setting it may be on OFF
• check that the correct terminals have been used
• check external wiring for a short
• set the dehumidistat at the desired setting
Dehumidistat is not Operating
• dehumidistat is set too high
.• lifestyle of the occupants
• set dehumidistat lower
• avoid hanging clothes to dry, storing wood and venting clothes
dryer inside. Heating wood may have to be moved outside
Humidity Levels are too High in Winter
Condensation is appearing on the
windows
• moisture coming into the home from an unvented or • vent crawl space and place a vapor barrier on the floor of the
unheated crawl space crawl space
• moisture is remaining in the washroom/bathroom and • ducts from the washroom/bathroom should be sized to remove
kitchen areas
moist air as effectively as possible, use of a washroom/bath-
room fan for short periods will remove additional moisture
• timer or fan can be added to washroom/bathroom exhaust
• on humid days, as the seasons change, some condensation
may appear but the home’s air quality will remain high with
some HRV use
• condensation seems to form in the spring and fall
• HRV is set at too low a speed
• increase speed of the HRV
• dehumidistat control set too low
• blower speed of HRV is too high
• lifestyle of occupants
• set dehumidistat higher
• decrease HRV blower speed
• humidity may have to be added through the use of humidifiers
• have a contractor balance HRV air flow
Humidity Levels are too Low
• HRV air flow may be improperly balanced
• Note: minimal frost build-up is expected on cores before
unit initiates defrost cycle functions
HRV and / or Ducts Frosting up
• HRV air flow is improperly balanced
• malfunction of the HRV defrost system
• have HVAC contractor balance the HRV
• ensure working properly.
• incomplete vapor barrier around insulated duct
• tape and seal all joints
Condensation or Ice Build Up in
• a hole or tear in outer duct covering
• tape any holes or tears made in the outer duct covering
• ensure that the vapor barrier is completely sealed
Insulated Duct to the Outside
• drain pans plugged
• improper connection of HRV drain lines
• HRV is not level
• ensure O-Ring on drain nozzle sits properly
• look for kinks in line
• check water drain connections
Water in the bottom of the HRV
• drain lines are obstructed
• make sure water drains properly from pan
• HRV heat exchange core is not properly installed
• Wiring
• Faulty control
• Faulty circuit board
• disconnect external controls and run unit through self test. If
the unit runs through self test successfully, then the circuit
board is okay.
20 Minute Timer Not Working
• check wiring connection.
• make sure wires are connected to proper terminals.
• test 20 Minute Timer, press and hold the button for 10 seconds
then release. The unit should run on high speed and then return
to normal operation when the button is released.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
HRV
1. Inspect Exterior Hoods at least once a month.
Make sure exhaust and fresh air supply hoods are not
blocked or restricted by leaves, grass, or snow. In winter, it
is especially important to make sure snow is not blocking
the hoods or that frost has not built up on the wire mesh
(bird screen).
4. Motors - Maintenance Free
5. Drain (condensate) Line - Clean Once a Year
Inspect drain line, drain spout and “P” trap for blockage,
mold or kinks. Flush with warm soapy water and replace if
worn, bent or unable to clean.
6. Clean Duct System if Required
WARNING: Blockage of hoods may cause an imbalance.
The duct system running to and from the HRV may accu-
mulate dirt. Wipe and vacuum the duct once every year.
You may wish to contact a Heating/Ventilation company to
do this.
2. Clean Air Filters - Twice a Year
The standard filters equipped with your HRV are remov-
able and washable.
7. General Maintenance - Twice a Year
a) simply open access door and slide core out
b) remove filters
Wipe down the inside of the cabinet with a damp cloth to
remove dirt, bugs and debris that may be present. Pay
special attention to the drain pan and ensure water flow
path is not blocked.
c) rinse with water or a combination of mild soap and
water. Do not clean in the dishwasher
d) to re-assemble, place clean filter(s) (wet or dry) back
into their positions against the core and return clips to
their original position
8. Cleaning the Fans
Fans may accumulate dirt causing an imbalance and/or
excessive vibration of the HRV. A reduction in the air flow
may also occur. In new construction this may result within
the first year due to heavy dust and may occur periodically
after that over time depending on the outdoor conditions.
e) slide core back into its original position
3. Clean Core - Twice a Year
a) open access door
b) rotate keeper clips and carefully grip ends of core and
pull evenly outward.
• unplug the HRV and open the service door
• remove the core
-core may be snug, but will slide out of the channel
c) once removed from the cabinet remove filters
• use a small brush, such as a toothbrush or pipe
cleaner, and insert first. Scrub individual fan blades until
clean. Avoid moving or damaging balancing flat weight,
clip is usually found on one or more of the fan blades
d) wash core in warm soapy water
(do not use dishwasher)
• vacuum and wipe
e) install clean core
Before attempting this task, thought should be given
to having a qualified service technician complete the
service work.
f) install the clean filters
Note: Core installation label on the outer end of the core.
To install the clean core:
a) first mount the bottom flange of the core guide into the
bottom H channel approximately 1/4” (6mm)
b) mount the left or right side flange of the core guide
approximately 1/4” (6mm) followed by the other side
c) mount the top flange of the core guide into the top H
channel approximately 1/4” (6mm)
d) with all four corners in place and the core straight and
even, push hard in the center of the core until the core
stops on the back of the cabinet
e) rotate core clips to lock core in place
NOTE: Core will appear to stick out from cabinet approxi-
mately 1/8” (3mm). This is designed this way so that the
access door will fit tight against the core.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Record
Note: It is important to maintain this product regularly to ensure optimal performance.
Date
Maintenance Performed
Contractor
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|