Liebert Surge Protector Power Strips User Manual

LIEBERT MP™ ADVANCED POWER STRIPS  
QUICK-START GUIDE: OPENCOMMS EM OR MP ADVANCED ACCESS SERVER  
SAVE THESE IMPORTANT SAFETY INSTRUCTIONS  
This manual contains important safety instructions. Read all safety, installation and operating  
instructions before installing the Liebert MP Advanced Power Strip or Access Server. Adhere to all  
warnings on the unit and in this manual. Follow all operating and user instructions. Individuals  
without previous training can install and operate this equipment.  
The Liebert MP Advanced Power Strip and Access Server are not intended for use with life support or  
other designated critical devices. Maximum load must not exceed that shown on the Liebert MP  
Advanced Power Strip or Access Server rating label. The Liebert MP Advanced Power Strip and  
Access Server are designed for data processing equipment. If uncertain, consult your local dealer or  
Liebert representative.  
WARNING  
!
Opening or removing the cover of MP Advanced Power Strips or Access Servers may expose  
you to lethal voltages within the unit.  
Observe all cautions and warnings in this manual. Failure to do so may result in serious  
injury or death. Do not attempt to service this product yourself. Refer all service to qualified  
service personnel. Never work alone.  
Operate the Liebert MP Advanced Power Strip and Access Server in an indoor environment only in an  
ambient temperature range of 32°F to +104°F (0°C to +40°C). Install it in a clean environment, free  
from conductive contaminants, moisture, flammable liquids, gases and corrosive substances.  
WARNING  
!
The Liebert MP Advanced Power Strip and Access Server contain no user serviceable parts.  
Under no circumstances attempt to gain internal access due to risk of electric shock or burn.  
Do not continue to use the Liebert MP Advanced Power Strip or Access Server if the LED  
panel or monitoring interface indicators are not in accordance with these operating  
instructions. Refer all faults to your local dealer or Liebert representative.  
Never block or insert any object into the Liebert MP Advanced Power Strip or Access Server.  
DO NOT CONNECT equipment that could overload the Liebert MP Advanced Power Strip or Access  
Server.  
Refer to the Liebert MP Advanced Power Strip and Access Server user manual, SL-20815, to deter-  
mine the electrical ratings and specifications of your Liebert MP Advanced Power Strip or Access  
Server. It is imperative that the power supply and connections match the specifications of the power  
strip or access server being installed.  
CAUTION  
!
Connecting your Liebert MP Advanced Power Strip, Access Server or rack equipment to a  
power supply with an incorrect rating in either voltage, amperes or phase may damage the  
connected equipment and your Liebert MP Advanced Power Strip or Access Server.  
If you have questions about the power supply connections, contact your local Liebert  
representative or Liebert Technical Support at 1-800-222-5877.  
CAUTION  
!
Shut down and unplug all equipment in your rack enclosure before beginning to connect the  
equipment to your Liebert MP Advanced Power Strip or Access Server.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSIGN AN IP ADDRESS  
NOTE  
These steps must be done on the same network segment where the OpenComms EM is connected.  
If your network uses static IP addresses and your computer has a Windows operating system, follow the  
steps below. Otherwise, consult the OpenComms EM user manual (SL-28210).  
1. Obtain an IP address for the OpenComms EM from your network administrator.  
2. Insert the OpenComms EM CD in your computer’s CD drive.  
3. Click on the Start button, then on Run, then Browse to the file IPSET.exe on the CD and click  
Open.  
4. Click OK to open the IPSet window (at right).  
5. In the Target area:  
a. Enter the OpenComms EM IP address  
b. Enter your network’s Subnet Mask  
c. Enter your router’s IP address in the Default  
box.  
d. Enter the MAC address found on the bottom  
of your OpenComms EM.  
Enter a  
unique  
IP address  
Subnet  
mask  
Default  
gateway  
address  
6. Apply the changes. If the device identification is  
successful, the message “Successfully set IP  
address” appears in the Status box. (If not, the  
message “No response from target” appears in  
the Status box.)  
Enter the unit’s  
MAC address  
(look on  
bottom of unit)  
Apply button  
7. Click on the Close button.  
OPEN THE WEB INTERFACE AND LOG IN  
• Open an Internet browser and enter the unit’s IP address or hostname into the browser’s address bar  
and press the Enter key. The Login window appears.  
Address  
bar  
Login  
window  
User Name  
default = “liebert”  
Password  
default = no password  
• Enter the default user name—liebert— in the User Name box (case-sensitive).  
• Leave the Password box blank (the default liebert user account has no password).  
• Click OK. If the login is successful, a message appears. Click OK.  
When ready to exit the user interface, click on the Summary tab at the top of the Web interface, then  
click on the Log Out button in the left side of the window.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONFIGURATION WITH LIEBERT MP ADVANCED ACCESS SERVER  
Liebert MP Advanced  
Power Strip  
(MP-C5120)  
Mounting  
Bracket on  
either side  
EIA-232  
EIA-232 Port  
1
2
3
4
5
6
8
8
POWER  
EIA-232 Port - Connect  
to Power Strip EIA-232 Port  
MP-DS74 Card With  
Configurable  
Communication Ports  
Ethernet Port  
Liebert MP Advanced  
Access Server  
(MP-S5138)  
100-240VAC  
??????????  
0.21-0.12AMPS  
On/Off Switch  
(not on all  
models)  
ROUTE  
LINE  
MADE IN USA  
MAKE CONNECTIONS  
1. Connect power to the Liebert MP Advanced Access Server and turn the unit On (the On/Off switch is  
on the rear of the unit; some units do not have this switch; they are energized whenever their power  
cord is plugged into a power source).  
2. Attach the adapter (RS-232 to RJ-45) to one end of a silver configuration cable (included) and connect  
that end of the cable to a COM port on a computer. Connect the other end of the cable to the EIA-232  
port of the MP-DS62 card on your MP Advanced Access Server.  
3. Plug one end of the second silver RJ-45 cable into any of the ports in the MP-DS74 module in your  
Liebert MP Advanced Access Server; plug the other end of the cable into the EIA-232 port on your MP  
Advanced Power Strip.  
HYPERTERMINAL SETTINGS  
ESTABLISH COMMUNICATION WITH CARD  
1. Use terminal emulation software, such as HyperTerminal™, to open a  
Baud Rate: 9600  
Data Bits:  
Parity:  
Stop Bits:  
8
direct connection to the MP-DS62 card. Use the settings at right. Press  
Enter for the Main Menu, choose “C” and then “1” to configure the  
MP-DS62 port.  
None  
1
Flow Control: N/A  
2. Enter “8” for Network Port Configuration (below left), then “7,” then “N”  
to disable DHCP (below right).  
Enter “N”  
to disable  
DHCP  
Enter “7”  
to change  
DHCP setting  
Choose “8” to change  
Network Port  
Configuration  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET THE IP ADDRESS  
1. Select “1” to set the IP Address for Module 1. Enter an IP address (below). The address must be  
unique on your system (obtain this from your network administrator).  
2. Press Enter to return to the Network Port Configuration menu.  
Enter IP address  
3. Choose “2” to set the Subnet Mask for your system (obtain this from your network administrator).  
SET THE GATEWAY ADDRESS  
1. Return to the Network Port Configuration menu and choose “3” to set the Gateway Address (the IP  
address of your network router). Follow the prompts to exit HyperTerminal and save your changes.  
2. Verify that your settings are correct and were saved by using a command prompt to ping the  
MP-C/MP-S unit: Start>Run>CMD.  
3. At the command prompt enter:  
ping [IP address]  
4. Press “Enter.”  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Liebert Corporation  
1050 Dearborn Drive  
P.O. Box 29186  
Columbus, OH 43229  
Telephone: 1-800-877-9222  
Facsimile: 1-614-841-6022  
© 2006 Liebert Corporation  
® Liebert and the Liebert logo are registered trademarks of  
All rights reserved throughout the world. Specifications subject Liebert Corporation. All names referred to are trademarks or  
to change without notice.  
registered trademarks of their respective owners.  
SL-20812 (01/06) Rev. 2  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kyocera Cell Phone DURAMAX BY KYOCERA User Manual
Lenovo Computer Hardware 3000 C200 User Manual
LG Electronics Washer WM2496H User Manual
Lindy Battery Charger 84871 User Manual
Linksys Network Router WRT100 User Manual
Makita Chainsaw DPC 6400 DPC 6401 DPC 7300 DPC 7301 User Manual
Makita Cordless Drill 60921 User Manual
Master Bilt Refrigerator QMVM 36L User Manual
Master Lock Electric Heater 100000 BTU Hr User Manual
Maytag Washer Dryer MED User Manual