R
PORTABLE
FORCED
AIR HEATERS
OWNER’S MANUAL
100 SIDE
PV 002
150 SIDE HANDLE
PFA/PV 005
Heater Sizes: 70,000 100,000 150,000 BTU/Hr
IMPORTANT
Read and understand this manual before assembling, starting or servicing
heater. Improper use of heater can cause serious injury. Keep this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
INFORMATION
!
WARNINGS
IMPORTANT: Read this owner’s manual carefully and completely
before trying to assemble, operate, or service this heater. Improper
use of this heater can cause serious injury or death from burns, fire,
explosion, electrical shock, and carbon monoxide poisoning.
!
DANGER
Carbon monoxide poisoning may lead to death!
Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning
resemble the flu, with headaches, dizziness, or nausea. If you have these signs, the
heater may not be working properly. Get fresh air at once! Have heater serviced.
Some people are more affected by carbon monoxide than others. These include
pregnant women, persons with heart or lung disease or anemia, those under the
influence of alcohol, and those at high altitudes.
Make certain you read and understand all warnings. Keep this manual for
reference. It is your guide to safe and proper operation of this heater.
• Use only kerosene or No. 1 fuel oil to avoid risk of fire or explosion. Never
use gasoline, naphtha, paint thinners, alcohol, or other highly flammable
fuels.
• Never use heater where gasoline, paint thinner, or other highly flammable
vapors are present.
• Follow all local ordinances and codes when using heater.
• Use only in well-vented areas. Provide at least a three-square-foot (2800
square cm) opening of fresh, outside air for each 100,000 BTU/Hr of rating.
• Use only in places free of flammable vapors or high dust content.
• Use only with the electrical voltage and frequency specified on model plate.
• Use only a three-wire, grounded (earthed) extension cord.
• Minimum heater clearances from combustibles:
Outlet: 8 Ft. (250 cm)
Sides, Top, and Rear: 4 Ft. (125 cm)
• Locate heater on a stable and level surface while hot or running or a fire may
occur.
• When moving or storing heater, keep heater in a level position or fuel
spillage may occur.
• Keep children and animals away from heater.
• Unplug heater when not in use.
• When used with thermostat, heater may start anytime.
• Never use heater in living or sleeping areas.
• Never block air inlet (rear) or air outlet (front) of heater.
• Never move, handle, refuel, or service a hot, operating, or plugged-in heater.
• Never attach duct work to front or rear of heater.
3
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot Air Outlet
Upper Shell
Handle
PRODUCT
IDENTIFICATION
Fan Guard
Lower Shell
Fuel Tank
Side Cover
Air Filter
End Cover
Fuel Cap
Flame-Out
Control Reset
Button
Power Cord
35/50/70,000 BTU/HR DOMESTIC
PFA/PV 042
Figure 1 - 70,000 BTU/Hr Model
Hot Air
Outlet
Upper Shell
Lower
Shell
Fuel Cap
Fan Guard
Fuel Tank
Side Cover
Power Cord
Flame-Out Control
Reset Button
Hot Air
Outlet
Figure 2 - 100,000 BTU/Hr Model
Upper Shell
Lower
Shell
Fan Guard
Fuel
Tank
Fuel Cap
Slide Cover
Power Cord
Flame-Out
Control Reset
Button
Figure 3 - 150,000 BTU/Hr Model
4
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Remove all packing items applied to heater for shipment.
2. Remove all items from carton.
3. Check items for any shipping damage. If heater is damaged, promptly inform
dealer where you bought heater.
UNPACKING
ASSEMBLY
These models are furnished with wheels and handles. Wheels, handles, and the
mounting hardware are found in the shipping carton.
(For 100,000 and 150,000
BTU/Hr Models Only)
Tools Needed
• Medium Phillips Screwdriver
• 3/8" Open or Adjustable Wrench
• Hammer
1. Slide axle through wheel support frame. Install wheels on axle.
IMPORTANT: When installing wheels, point extended hub of wheels toward
wheel support frame (see Figure 4).
2. Place cap nuts on axle ends. Gently tap with hammer to secure.
3. Place heater on wheel support frame. Make sure air inlet end (rear) of heater is
over wheels. Line up holes on fuel tank flange with holes on wheel support
frame.
4. Place front handle and rear handle on top of fuel tank flange. Insert screws
through handles, fuel tank flange, and wheel support frame. Attach nut finger
tight after each screw is inserted.
5. After all screws are inserted, tighten nuts firmly.
Front
Handle
Rear
Handle
Screw
Hot Air
Outlet
Air
Inlet
Fuel
Tank
Flange
Wheel
Support
Frame
Wheel
Nut
Extended
Hub
Cap Nut
Axle
Figure 4 - Wheel and Handle Assembly,100/150,000 BTU/Hr Models Only
5
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
The Fuel System: The air pump forces air through the air line. The air is then
pushed through the burner head nozzle. This air causes fuel to lift from the tank. A
fine mist of fuel is sprayed into the combustion chamber.
THEORY OF
OPERATION
The Air System: The motor turns the fan. The fan pushes air into and around
the combustion chamber. This air is heated and provides a stream of clean, hot air.
The Ignition System: The electronic ignitor sends voltage to the spark plug.
The spark plug ignites the fuel and air mixture.
The Flame-Out Control System: This system causes the heater to shut down
if the flame goes out.
Motor
Fan
Air Pump
Combustion
Chamber
Spark
Plug
Intake
Air
Filter
Burner
Head
Clean
Heated
Air Out
Cool
Air
In
Output
Air
Filter
Fuel
Tank
Fuel
Filter
Nozzle
Air line
To Burner
Electronic
Ignitor
Air For Fuel
System
Air For Combustion
And Heating
Fuel
FigTuHrEeOR5Y-CCUTrAoWsAsY Section OperPaFtAio/OnVa0l03View
FUELS
WARNING
Use only kerosene or No. 1 fuel oil to avoid risk of fire or
explosion. Never use gasoline, naphtha, paint thinners,
alcohol or other highly flammable fuels.
Do not use heavy fuels such as No. 2 fuel oil or No. 2 Diesel. Using heavy fuels
will result in:
• clogged fuel filter and nozzle
• carbon build up on spark plug
• use of non-toxic anti-icer in fuel during very cold weather
IMPORTANT: Use a KEROSENE ONLY container. Be sure storage container is
clean. Foreign matter such as rust, dirt, or water will cause the flame-out control to
shut down heater. Foreign matter may also require you to clean fuel system often.
6
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTILATION
WARNING
Follow the minimum fresh, outside air ventilation
requirements. If proper fresh, outside air ventilation is not
provided, carbon monoxide poisoning can occur. Provide
proper fresh, outside air ventilation before running heater.
Provide a fresh air opening of at least three square feet (2800 square cm) for each
100,000 BTU/Hr rating. Provide extra fresh air if more heaters are being used.
Example: A 150,000 BTU/Hr heater requires one of the following:
• a two-car garage door raised six inches (15.24 cm)
• a single-car garage door raised nine inches (22.86 cm)
• two, thirty-inch (76.20 cm) windows raised twelve inches (30.48 cm)
WARNING
OPERATION
Review and understand the warnings in the Safety
Information Section, page 3. They are needed to safely
operate this heater. Follow all local codes when using this
heater.
To Start Heater
1. Follow all ventilation and safety information.
2. Fill fuel tank with kerosene or No. 1 fuel oil.
3. Attach fuel cap.
4. Plug power cord of heater into standard 230 volt/50 hertz, grounded (earthed)
outlet. Use an extension cord if needed. Use only a three-wire, grounded
(earthed) extension cord.
Extension Cord Wire Size Requirements
Up to 100 feet (30.5 meters) long, use 16 AWG (1.0 mm2) conductor
101 to 200 feet (30.6 to 61 meters) long, use 14 AWG (1.5 mm2) conductor
Heater will start when power cord is plugged into outlet. If not, push in flame-
out control reset button (see Figures 6 and 7).
Flame-Out
Control
Reset
Flame-
Out
Button
Control
Reset
Button
Figure 6 - Flame-Out Control Reset
Button, 70,000 BTU/Hr Model
Figure 7 - Flame-Out Control Reset
Button, 100/150,000 BTU/Hr Models
Continued
7
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
To Stop Heater
1. Unplug power cord from outlet.
OPERATION
Continued
To Restart Heater
1. Wait 2 minutes after stopping heater.
2. Repeat steps under To Start Heater, page 7.
1. Drain fuel tank.
STORAGE
Note: Some models have drain plug on underside of fuel tank. If so, remove
drain plug to drain all fuel. If heater does not have drain plug, drain fuel through
fuel cap opening. Be sure all fuel is removed.
2. Replace drain plug if used.
3. Add one gallon (4 liters) of clean kerosene to fuel tank.
4. Attach fuel cap.
5. Move heater forwards and backwards to stir fuel.
6. Remove fuel cap or drain plug and drain fuel tank. Be sure all fuel is removed.
7. Replace fuel cap or drain plug. Properly dispose of old and dirty fuel.
8. Store heater in dry place. Make sure storage place is free of dust and corrosive
fumes.
IMPORTANT: Do not store kerosene over summer months for use during next
heating season. Using old fuel could damage heater.
PREVENTATIVE
MAINTENANCE
SCHEDULE
WARNING
Never service heater while it is plugged in, operating, or
hot. Severe burns and electrical shock can occur.
Item
How Often
How To
Fuel tank
Flush every 150-200 hours
of operation or as needed.
See Storage above.
Air output and
Replace every 500 hours of
lint filters operation or once
a year.
See Air Output, Air Intake,
and Lint Filters, page 12.
Air intake
filter
Wash and dry with soap and
water every 500 hours of
operation or as needed.
See Air Output, Air Intake,
and Lint Filters, page 12.
Fuel filter
Clean twice a heating season
or as needed.
See Fuel Filter, pages 10
and 11.
Spark plug
Clean and regap every 600
hours operation or replace
as needed.
See Spark Plug, page 11.
Fan blades
Motor
Clean every season or as needed.
See Fan, page 15.
Not required/permanently
lubricated
8
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-
SHOOTING
WARNING
Never service heater while it is plugged in, operating, or hot.
Severe burns and electrical shock can occur.
OBSERVED FAULT POSSIBLE CAUSE
REMEDY
Wrong pump pressure
See Pump Pressure
Adjustment, page 12.
Heater ignites, but
flame-out control
shuts off heater after
a short period of time
Dirty air output, air intake, See Air Output, Air Intake
and lint filters
and Lint Filters, page 12.
See Fuel Filter, pages 10
and 11.
Dirty fuel filter
Dirt in nozzle
See Nozzle, page 13.
Dirty photocell lens
Bad flame-out control
Clean photocell lens.
Replace flame-out control.
Heater will not
ignite, but motor runs
for a short period of
time.
Wrong pump pressure
See Pump Pressure
Adjustment, page 12.
Carbon deposits on spark
plug and/or improper gap
See Spark Plug, page 11.
Dirty fuel filter
See Fuel Filter, pages 10
and 11.
See Nozzle, page 13.
Dirt in nozzle
Drain and flush fuel tank
with clean kerosene. See
Storage, page 8.
Water in fuel tank
WARNING: High voltage!
Electronic ignitor not
Make sure electronic
grounded (earthed)
ignitor mounting is tight.
Bad electronic ignitor
Replace electronic
ignitor.
Motor does not start
when heater is
plugged in, fan
rotates slowly or
does not turn.
Flame-out control not reset
Binding pump rotor
Reset flame-out control
button, see Figures 6 and
7, page 7.
If fan is hard to turn, see
Pump Rotor, page 14.
9
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
PROCEDURES
WARNING
Never service heater while it is plugged in, operating, or
hot. Severe burns and electrical shock can occur.
Upper
Shell
Upper Shell Removal
1. Remove screws along each
side of heater using 5/16"
nut-driver. These screws
attach upper and lower
shells together.
Fan
Guard
2. Lift upper shell off.
3. Remove fan guard.
Figure 8 - Upper Shell Removal, 70,000 BTU/Hr Model
Upper
Shell
Fan
Guard
Figure 9 - Upper Shell Removal, 100/150,000 BTU/Hr Models
Fuel Filter
Fuel Filter
(70,000 BTU/Hr Model)
1. Remove side cover screws
using 5/16" nut-driver.
2. Remove side cover.
3. Pull rubber fuel line off
fuel filter neck.
4. Carefully pry bushing and
fuel filter out of fuel tank.
5. Wash fuel filter with clean
fuel and replace in tank.
6. Attach rubber fuel line to
fuel filter neck.
Side Cover
Fuel Line
7. Replace side cover.
Figure 10 - Fuel Filter Removal, 70,000 BTU/Hr Model
10
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
Fuel Filter, Bushing,
and Lower Fuel Line
Fuel Filter
(100/150,000 BTU/Hr Models)
1. Remove side cover screws
using 5/16" nut-driver.
2. Remove side cover.
3. Pull upper fuel line off fuel
filter neck.
Upper
Fuel Line
4. Carefully pry bushing,
lower fuel line, and fuel
filter out of fuel tank.
5. Wash fuel filter with clean
fuel and replace in tank.
6. Attach upper fuel line to
fuel filter neck.
7. Replace side cover.
Side Cover
Figure 11 -15F0u,0e00lBFTiUlt/Herr Removal, 100/150,000 BTU/Hr Models
PFA/P 041.G
Spark Plug
1. Remove upper shell (see
Spark Plug
Wire
Burner
Head
page 10).
2. Remove fan (see page 15).
3. Remove spark plug wire
from spark plug.
4. Remove spark plug from
burner head using 13/16"
open-end wrench.
5. Clean and regap spark plug
electrodes as follows:
70,000 BTU/Hr model:
.055" (1.4 mm) gap,
100/150,000 BTU/Hr
models: .075" (1.9 mm)
gap.
Spark
Plug
6. Install spark plug in burner
head.
SPARK PLUG REMOVAL 70, 100 &150
Figure 12 - Spark Plug Removal
PFA/P 031A
7. Attach spark plug wire to
spark plug.
8. Replace fan (see page 15).
9. Replace fan guard and
upper shell.
Bend Here
to Adjust
Gap
Gap
Figure 13 - Spark Plug Gap
11
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Intake Filter
Filter End
Air Output, Air Intake,
and Lint Filters
1. Remove upper shell (see
page 10).
Cover
Fan Guard
2. Remove filter end cover
screws using 5/16" nut-
driver.
3. Remove filter end cover.
4. Replace air output and lint
filters.
Lint Filter
Air Output
Filter
5. Wash or replace air intake
filter (see Preventative
Maintenance Schedule,
page 8).
Figure 14 - Air Output, Air Intake, and Lint Filters,
70,000 BTU/Hr Model
6. Replace filter end cover.
7. Replace fan guard and
upper shell.
Air Intake Filter
Fan Guard
Filter End
Cover
IMPORTANT: Do not oil
filters.
Lint Filter
Air Output
Filter
Figure 15 - Air Output, Air Intake, and Lint Filters,
100,000/150,000 BTU/Hr Models
Pump Pressure
Adjustment
(70,000 BTU/Hr Model Shown)
1. Remove pressure gauge
plug from filter end cover.
2. Install accessory pressure
gauge (part number
Pressure
Gauge
Plug
Relief
Valve
HA1180).
3. Start heater (see Operation,
page 7). Allow motor to
reach full speed.
PRESSURE GAUGE PLUG
PFA/OV 006B
Figure 16 - Pressure Gauge Plug Removal
4. Adjust pressure. Turn relief
valve to right to increase
pressure. Turn relief valve
to left to decrease pressure.
See specifications at right
for correct pressure for
each model.
5. Remove pressure gauge.
Replace pressure gauge
plug in filter end cover.
Pressure
Gauge
Pump
Pressure
4.5 PSI
4.5 PSI
4.9 PSI
Model
70,000 BTU/Hr
100,000 BTU/Hr
150,000 BTU/Hr
Figure 17 - Adjusting Pump Pressure
12
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
Nozzle
1. Remove upper shell (see
Combustion
Chamber
page 10).
2. Remove fan (see page 15).
3. Remove fuel and air line
hoses from burner head.
4. Remove spark plug wire
from spark plug.
Spark Plug
Wire
Burner Head
5. Remove spark plug from
burner head using 13/16"
open-end wrench.
6. Remove three screws
using 5/16" nut-driver and
remove burner head from
combustion chamber.
7. Place burner head into vise
and lightly tighten.
Screw
Spark
Plug
8. Carefully remove nozzle
from burner head using
5/8" socket wrench (see
Figure 19).
Air Line Hose
Fuel Line Hose
9. Blow compressed air
through face of nozzle.
This will free any dirt in
nozzle area.
Figure 18 - Removing Burner Head
10. Inspect nozzle seal for
damage.
11. Replace nozzle into burner
head and tighten firmly
(80-110 inch-pounds/9.1-
12.4 n-m).
12. Attach burner head to
combustion chamber.
13. Install spark plug in burner
head.
Nozzle
Face
Nozzle
Seal
Nozzle
14. Attach spark plug wire to
spark plug.
15. Attach fuel and airline
hoses to burner head.
16. Replace fan (see page 15).
17. Replace fan guard and
upper shell.
Burner
Head
Fuel line
Fitting
Air line
Fitting
Figure 19 - Removing Nozzle
13
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade
Pump
Plate
Air
Intake
Filter
Pump Rotor
(Procedure if rotor is binding)
1. Remove upper shell (see
page 10).
Filter End
Cover
2. Remove filter end cover
screws using 5/16" nut-
driver.
Fan Guard
3. Remove filter end cover
and air filters.
4. Remove pump plate
screws using 5/16" nut-
driver.
Insert
Rotor
Air Output
50 ROTOR
PFA/P 056
Filter
5. Remove pump plate.
6. Remove rotor, insert, and
blades.
Figure 20 - Rotor Location, 70,000 BTU/Hr Model
Pump
Blade
Plate
7. Check for debris in pump.
If debris is found, blow
out with compressed air.
8. Install insert and rotor.
9. Check gap on rotor.
Adjust to .003"/.004"
(.076/.101 mm) if needed
(see Figure 22).
Air
Intake
Filter
Filter End
Cover
Fan Guard
Insert
Rotor
Note: Rotate rotor one
full turn to insure the gap is
.003"/.004" (.076/.101 mm) at
tightest position. Adjust if
needed.
Air
Output
150 ROTOR
FilPteFrA/P 059
10. Install blades, pump plate,
air filters, and filter end
cover.
Figure 21 - Rotor Location, 100/150,000 BTU/Hr Models
11. Replace fan guard and
upper shell.
Gap Adjusting
Screw
12. Adjust pump pressure (see
page 12).
Note: If rotor is still binding,
proceed as follows.
.003"/.004"
(.076/.101 mm) Gap
Measured With
Feeler Gauge
Sandpaper
13. Perform steps 1 through 6
above.
14. Place fine grade sandpaper
(600 grit) on flat surface.
Sand rotor lightly in
Blade
Rotor
“figure 8” motion four
times (see Figure 23).
15. Reinstall insert and rotor.
16. Perform steps 10 through
12 above.
Gap
Adjusting
Screw
Figure 22 - Gap Adjusting
Screw Locations
Figure 23 - Sanding Rotor
14
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
Fan
IMPORTANT: Remove fan
from motor shaft before
removing motor from heater.
The weight of the motor
resting on the fan could
damage the fan pitch.
Fan
Setscrew
1. Remove upper shell (see
page 10).
2. Use 1/8" allen wrench to
loosen setscrew which
holds fan to motor shaft.
3. Slip fan off motor shaft.
4. Clean fan using a soft cloth
moistened with kerosene or
solvent.
Motor
Shaft
Figure 24 - Fan, Motor Shaft, and Setscrew Location
5. Dry fan thoroughly.
6. Replace fan on motor
shaft. Place fan hub flush
with end of motor shaft
(see Figure 25).
7. Place setscrew on flat of
shaft. Tighten setscrew
firmly (40-50 inch-pounds/
4.5-5.6 n-m).
Fan
8. Replace fan guard and
upper shell.
Flush
Motor
Shaft
Setscrew
Figure 25 - Fan Cross Section
Output Rating (BTU/Hr)
Fuel
70,000
100,000
150,000
SPECIFICATIONS
Use Only Kerosene or No. 1 Fuel Oil
Fuel Tank Capacity
(U.S. Gal./Liters)
5.0/18.9
.52/1.97
9.0/34.1
.78/2.95
13.5/51.1
1.10/4.16
Fuel Consumption
(Gal. Per Hr./Liters Per Hr.)
Electric Requirements
Amperage (Normal Run)
Hot Air Output (CFM/CMM)
RPM
220 V/60 Hz (Same All Models)
2.0
2.0
490/13.9 500/14.2
3450 3450
2.0
250/7.1
3450
15
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
3
ILLUSTRATED
PARTS
1
BREAKDOWN
2
70,000 BTU/Hr
4
5
10
7
8
6
14
12
12
11
18
15
16
19
17
23
24
21
20
25
22
10-1
10-2
35
43
36
27
44
26
29
10-3
10-4
31
32
28
30
33
10-7
10-5
38
39
37
10-6
34
Burner Head Assembly
18-1
18-2
40
13
18-3
41
9
18-4
18-5
18-6
42
18-7
45
18-18
18-8
18-17
18-16
18-9
18-10
18-11
18-12
18-15
18-14
Motor and Pump Assembly
18-13
16
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
This list contains replaceable parts used in your heater. When ordering parts,
be sure to provide the correct model and serial numbers (from the model plate),
then the part number and description of the desired part.
PARTS LIST
70,000 BTU/Hr
KEY PART
PART
DESCRIPTION
KEY PART
NO. NUMBER
PART
DESCRIPTION
NO.
NUMBER
QTY.
QTY.
18-14 M29612-01
18-15 M12461-31
18-16 M50016
18-17 M8643
18-18 FHPF3-2C
Output Filter
1
6
1
4
2
1
2
1
6
1
6
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
M51104-01
098511-54
100647-01
098512-34
M11084-29
M16660
Handle
Upper Shell
1
1
6
1
2
1
2
1
1
1
1
2
1
1
1
2
1
3
2
1
1
2
2
Screw, #10-32 x 1"
Elbow, 90˚ (Barb Fitting)
Blade
Screw, #10-32 x 1/4"
Fan Guard
Screw, #10-16 x 1/2"
Combustion Chamber
Screw, #10-16 x 3/4"
Photocell Bracket
Screw, #6-32 x 3/8"
Photocell Assembly
Power Cord
19
M51105-01
NTC-4C
20
21
22
23
24
25
26
27
28
29
30
31
32
Hex locknut
M10908-2
HA3019
M50104-02
M11084-26
098511-12
M11271-8
M12462-15
M16841-58
M15823-39
M29652-04
079973-01
M16841-57
M10990-3
M50876-05
Bushing (wires)
Screw, #10-16 x 3/8"
Lower Shell
099055-07
**
10
Burner Head Assembly
Nozzle
Clip Nut
10-1 M50880-01
10-2 M10659-1
10-3 M10809-1
10-4 M8882
Relay (motor start)
Wire Assembly (red 9 1/2")
Screw, #8-18 x 1/2"
Rubber Airline
Nozzle Seal Washer
Nozzle Seal Spring
Nozzle Seal Sleeve
Burner Head Body
Barb Fitting
10-5 M51098-02
10-6 M50820-01
10-7 M10962-2
Fuel Line
Wire Assembly (red 8 1/2")
Rubber Bushing
Fuel Filter Assembly
(Includes bushing)
Electronic Ignitor
Screw, #10-16 x 3/4"
Terminal Board
Rivet
Spark Plug
Screw, #10-16 x 1/2"
Bushing
Strain Relief Bushing
Fan
Rubber Bumper
Screw, #8-32 x 1/4"
(holds relay in position)
Motor and Relay
Bracket Assembly
Motor and Pump Assembly
Motor (220V/60Hz)
Pump Body
11
M11084-27
M30865-02
M11143-1
101587-01
M50631
12
13
14
15
16
33
34
35
36
37
38
39
40
41
42
43
44
45
098557-07
M11084-29
099125-02
099157-01
097702-01
097630-02
098513-62
1
2
1
1
1
1
1
1
2
1
1
1
1
M12461-13
Fuel Tank Cap
Flame-Out Control
Fuel Tank
17
18
098138-01
**
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
M50899-03AA Side Cover
18-1 099656-02
18-2 079975-02
18-3 M22009
18-4 M22456-1
18-5 M29608
18-6 M29632
18-7 M29633
18-8 M29609
18-9 M12461-31
18-10 M8940
M11084-26
099177-01
078918-01
M9900-162
M27417
Screw, #10-16 x 3/8"
Hex Nut
Terminal Board Tab Cap
Wire Assembly (green 16")
Drain Plug
Insert
Rotor
End Pump Cover
Lint Filter
Intake Filter
PARTS AVAILABLE - NOT SHOWN
End Filter Cover
Screw, #10-32 x 1"
Steel Ball (1/4" Dia.)
Pressure Relief Spring
Adjusting Screw
Plug
M18053
Filler Neck Screen
Wiring Decal
Tradename Decal
General Information Decal
1
1
2
1
098227-53
097649-01
098493-01
18-11 M10993-1
18-12 M27694
18-13 M22997
**Not available as an assembly, order parts separately.
17
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATED
PARTS
2
BREAKDOWN
1
100,000 BTU/Hr
3
4
5
8
12
13
14
7
15
16
8-1
9
10
17
8-2
11
30
20
19
31
18
28
21
25
8-3
8-4
27
23
24
36
22
29
8-7
33
34
35
8-5
32
44
26
BURNER HEAD 100 EAI/EBI
PFA/P 022
37
8-6
Burner Head Assembly
38
39
45
42
41
13-1
13-3
13-4
13-5
40
13-2
43
6
13-6
13-7
13-18
13-17
13-8
13-9
13-16
13-15
13-10
13-11
13-14
13-13
13-12
Motor and Pump Assembly
18
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
This list contains replaceable parts used in your heater. When ordering parts,
be sure to provide the correct model and serial numbers (from the model plate),
then the part number and description of the desired part.
PARTS LIST
100,000 BTU/Hr
KEY
PART
PART
KEY
PART
PART
NO.
NUMBER
DESCRIPTION
QTY. NO.
NUMBER
DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
8-1
8-2
8-3
8-4
8-5
8-6
8-7
9
10
11
12
13
098511-138
100647-01
098512-31
M16660
HA3019
M27417
M10908-2
**
M23103
M10659-1
M10809-1
M8882
M50924-03
M50820-02
M10962-2
M11084-27
M50814-06
M51345-01
097293-01
**
Upper Shell
1
8
1
1
1
1
2
1
1
2
1
1
1
2
1
3
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
4
1
6
1
1
4
1
15
16
17
M50631
M12461-13
098138-02
Rubber Bumper
Screw, #8-32 x 1/4"
Motor and Relay
Bracket Assembly
Relay (motor start)
Wire Assembly (red 13 1/2")
Hex locknut
Electronic Ignitor
Screw, #10-16 x 3/4"
Terminal Board
Rivet
Bushing
Wire Assembly (green 16")
Bushing
Button Plug
Screw, #10-16 x 1/2"
Lower Shell
Clip Nut
Screw, #8-18 x 1/2"
Fuel filter
Rubber Bushing
Fuel Line
Fuel Tank
Fuel Tank Cap
Wire Assembly (red 8 1/2")
Flame-Out Control
Strain Relief Bushing
Power Cord
2
2
Screw, #10-16 x 1/2"
Combustion Chamber
Photocell Bracket
Photocell Assembly
Drain Plug
Screw, #6-32 x 3/8"
Burner Head Assembly
Nozzle
Nozzle Seal Washer
Nozzle Seal Spring
Nozzle Seal Sleeve
Burner Head Body
Barb Fitting
Spark Plug
Screw, #10-16 x 1/2"
Air Line
Fuel Line
Fan
Motor and Pump Assembly
Motor (220V/60Hz)
Pump Body
Screw, #10-32 x 1/4"
Insert
Rotor
End Pump Cover
Intake Filter
1
1
1
2
1
2
1
1
2
1
2
1
6
1
8
1
1
1
1
1
1
1
1
1
1
1
4
1
1
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
M12462-15
M16841-59
NTC-4C
098557-07
M11084-29
099125-02
099157-01
M50104-03
M9900-192
M50104-01
099213-01
M11084-27
098511-140
M11271-8
M15823-39
M51150-01
M10990-3
M51151-01
098513-21
097702-01
M16841-57
097630-02
M11143-1
099055-07
13-1 099656-01
13-2 079975-02
13-3 FHPF3-2C
13-4 M22009
13-5 M22456-1
13-6 M50545
13-7 M12179
13-8 M16545
13-9 M8940
13-10 M10993-1
13-11 M27694
13-12 M22997
13-13 M12461-31
13-14 M12244-1
13-15 M12461-31
13-16 M11637
13-17 M50820-02
13-18 M8643
End Filter Cover
Steel Ball (1/4" Dia.)
Pressure Relief Spring
Adjusting Screw
Plug
Screw, #10-32 x 1"
Output Filter
Screw, #10-32 x 1"
Lint Filter
M51077-01AA Side Cover
M11084-27
078918-01
099177-01
Screw, #10-16 x 1/2"
Terminal Board Tab Cap
Hex Nut
PARTS AVAILABLE - NOT SHOWN
M18053
Filler Neck Screen
Wiring Decal
Tradename Decal
General Information Decal
1
1
2
1
Barb Fitting
Blade
Fan Guard
098227-53
097650-01
098493-01
14
M51114-01
**Not available as an assembly, order parts separately.
19
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATED
PARTS
BREAKDOWN
2
150,000 BTU/Hr
1
3
4
44
6
7
9
46
10
5
16
8
11
7-1
14
19
23
7-2
12
24
15
39
28
37
13
45
25
17
7-3
7-4
26
38
27
18
20
7-7
22
21
7-5
29
43
47
30
BURNER HEAD 100 EAI/EBI
PFA/P 022
7-6
Burner Head Assembly
31
40
32
42
10-1
35
10-3
10-4
10-5
10-2
33
34
36
10-6
41
10-7
10-18
10-17
10-8
10-9
10-16
10-15
10-10
10-11
10-14
10-13
10-12
Motor and Pump Assembly
20
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
This list contains replaceable parts used in your heater. When ordering parts, be
sure to provide the correct model and serial numbers (from the model plate), then
the part number and description of the desired part.
PARTS LIST
150,000 BTU/Hr
KEY
NO.
PART
NUMBER
KEY
NO.
PART
NUMBER
QTY.
QTY.
DESCRIPTION
DESCRIPTION
1
2
3
4
5
6
7
098511-138
100647-01
098512-29
099229-01
M10908-2
HA3019
Upper Shell
1
8
1
1
2
1
1
1
2
1
1
1
2
1
3
1
1
1
1
2
1
1
1
1
1
1
1
1
1
4
1
6
1
1
4
2
1
1
2
2
1
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
098557-07
M11084-29
M51345-02
M51150-01
M51151-02
M10990-3
M50814-03
098511-140
M50104-03
M50104-01
M11084-27
M11271-8
M15823-39
098513-56
097702-01
097630-02
M11143-1
099055-07
Ignitor Kit
Screw, #10-16 x 3/4"
Fuel Line
1
2
1
1
1
1
1
1
2
2
6
8
1
1
1
1
1
1
1
4
1
1
Screw, #10-16 x 1/2"
Combustion Chamber
Photocell Bracket
Screw, #6-32 x 3/8"
Photocell Assembly
Burner Head Assembly
Nozzle with Sleeve
Nozzle Washer
Nozzle Spring
Nozzle Sleeve
Burner Head Body
Barb Fitting
Spark Plug
Screw, #10-16 x 1/2"
Fan
Motor and Pump Assembly
Motor (220V/60Hz)
Pump Body
Screw #10-32 x 1/4"
Rotor Insert
Pump Rotor
Pump End Cover
Intake Filter
Filter End Cover
Steel Ball, 1/4" diameter
Relief Spring
Adjusting Screw
Plug
Screw #10-32 x 1"
Output Filter
Screw, #10-32 x 1"
Lint Filter
Fuel Filter
Fuel Line Tube
Rubber Bushing
Air Line
Lower Shell
Bushing
Bushing
Screw, #10-16 x 1/2"
Clip Nut
Screw, #8-18 x 1/2"
Fuel Tank
Fuel Tank Cap
Flame-Out Control
Strain Relief Bushing
Power Cord
**
7-1
HA3010
7-2
7-3
7-4
7-5
7-6
7-7
M10659-1
M10809-1
M8882
M50924-03
M50820-02
HA3012
M11084-27
097293-01
**
8
9
10
10-1 099656-01
10-2 079975-02
10-3 FHPF3-2C
10-4 M22009
10-5 M22456-1
10-6 M50545
10-7 M12179
10-8 M16545
10-9 M8940
10-10 M10993-1
10-11 M27694
10-12 M22997
10-13 M12461-31
10-14 M12244-1
10-15 M12461-31
10-16 M11637
10-17 M50820-02
10-18 M8643
M51077-01AA Side Cover
M11084-27
099125-03
099157-01
M16841-59
Screw, #10-16 x 1/2"
Terminal Board
Rivet
Wire Assembly
(Red, 13 1/2")
Wire Assembly (Red, 6")
Drain Plug
(Includes “O” Ring)
Hex Nut
Tab Cap
Screw, #10-16 x 3/8"
Button Plug
Screw, #10-16 x 1/2"
Wire Assembly
(Green, 16")
1
1
40
41
M16841-57
M27417
1
1
1
2
1
2
42
43
44
45
46
47
099177-01
078918-01
099230-01
099213-01
M11084-27
M9900-192
Barb Fitting
Blade
1
11
M50631
Rubber Bumper
Motor Mounting Bracket
Motor Start Relay
Screw, #8-32 x 1/4"
Hex Lock Nut, 1/4-20
Fan Guard
PARTS AVAILABLE - NOT SHOWN
12
13
14
15
16
098138-02
M12462-15
M12461-13
NTC-4C
M18053
Filler Neck Screen
Tradename Decal
General Information Decal
Wiring Decal
1
2
1
1
097650-01
098493-01
098227-53
M51114-01
** Not available as an assembly. Order parts separately.
21
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEELS AND HANDLES FOR
100,000 AND 150,000 BTU/Hr MODELS
KEY PART
PART
100,000 150,000
NO. NUMBER
DESCRIPTION
QTY.
QTY.
1
HA2203
HA2204
Handles
Handles
2
—
8
1
—
8
2
2
1
—
—
2
8
—
1
8
2
2
—
1
2
3
M12345-33 Screw, #10-24 x 1 3/4"
M12342-3
M12831-3
NTC-3C
097896-01
M28526
Wheel Support Frame
Wheel Support Frame
Hex Nut, #10-24
Wheel
4
5
6
7
Cap Nut
M51015-01 Axle
M16801-2 Axle
1
2
3
4
5
7
6
22
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Plug
220V/60Hz
WIRING
DIAGRAMS
White
Black
Green
White
White
B
Spark Plug
Flame-
Out
Blue
White
Blue
Orange
Terminal
Board
Reset
Button
Ignitor
Motor
Control
Photocell
Red
Red
Green/
Yellow
R
Red
S or 2
Red
M or 3
Black
Motor
Start
Relay
L or 1
Figure 26 - Wiring Diagram
ACCESSORIES
Purchase accessories from
your local dealer.
AIR GAUGE KIT - HA1180
For all models. Special tool to
check pump pressure.
HEAVY DUTY WHEELS AND
HANDLE KIT - HA1202
For heavy duty applications.
Makes your heater even more
portable and convenient.
For 70,000 BTU/Hr model only.
23
101585
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND REPAIR SERVICE
CERTIFICATE OF GENERAL
EQUIPMENT - LIMITED 90 DAY WARRANTY
DESA International warrants new Products sold by it to be
POSE. IN ANY EVENT IMPLIED WARRANTIES INCLUDING
THOSEOFMERCHANTABILITYANDFITNESSFORAPAR-
TICULAR PURPOSE ARE LIMITED TO THE DURATION OF
THIS EXPRESS WARRANTY.
free from defects in material or workmanship for a period of
ninety days after date of delivery to the first user and subject to
the following conditions:
DESA International's obligation and liability under this
Warranty is expressly limited to repairing or replacing at DESA
International's option, any parts which appear to DESA Interna-
tional upon inspection to have been defective in material or
workmanship when shipped from the factory. Such parts shall
beprovidedatnocosttotheuser, atthebusinessestablishment
of any factory authorized service center or the factory during
regular working hours. The Warranty shall not apply to compo-
nent parts or accessories of Products not manufactured by
DESA International and which carry the warranty of the manu-
facturer thereof, or to normal maintenance (such as pressure
adjustments) or to normal maintenance parts (such as filters
and spark plugs). Replacement or repair parts installed in the
Product covered by this Warranty are warranted only for the
remainder of this Warranty as if such parts were original compo-
nents of said Product. DESA INTERNATIONAL MAKES NO
OTHER EXPRESS WARRANTY. TO THE EXTENT PERMIT-
TED BY LAW DESA INTERNATIONAL MAKES NO IMPLIED
WARRANTY AND MAKES NO WARRANTY OF MER-
CHANTABILITY OR FITNESS FOR ANY PARTICULAR PUR-
Any transportation charges, costs of installation, duty,
taxes or any other charges whatsoever must be borne by the
user. DESA International's obligation under this limited War-
ranty shall not include any liability for direct, indirect, incidental,
or consequential damage or delay. If requested by DESA
International, Products or parts for which a warranty claim is
made are to be returned transportation prepaid by user to the
factory. Any improper use, including operation after discovery
of defective or worn parts, operation beyond capacity, substi-
tution of parts not approved by DESA International, or any
alteration or repair by others in such manner as in DESA
International's judgement affects the Product materially and
adversely, shall void this Warranty.
NO EMPLOYEE OR REPRESENTATIVE IS AUTHORIZED
TO CHANGE THIS WARRANTY IN ANY WAY OR GRANT
ANY OTHER WARRANTY UNLESS SUCH CHANGE IS
MADEINWRITINGANDSIGNEDBYANOFFICEROFDESA
INTERNATIONAL AT ITS HOME OFFICE.
WARRANTY SERVICE
Always specify model and serial numbers when communicating
with the factory.
We reserve the right to amend these specifications at any time
without notice. The only Warranty applicable is our standard
written Warranty. We make no other Warranty, expressed or
implied.
A Service Manual is available by writing to the Technical Service
Department at:
DESA
INTERNATIONAL
Corporate Headquarters
2701 Industrial Drive
P.O. Box 90004
Bowling Green, Kentucky 42102-9004
U.S.A.
101585-01
Rev. B
9/94
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|