Liebert Surge Protector MP C5120 User Manual

LIEBERT MP™ ADVANCED POWER STRIPS  
QUICK-START GUIDE: OPENCOMMS EM OR MP ADVANCED ACCESS SERVER  
WHATS INCLUDED  
Make sure you have all the items that should be included with your Liebert MP Advanced Power Strip. If  
any item is missing or damaged in shipping, file a damage claim immediately—see the user manual for  
details.  
• RJ-45 to RJ-45 configuration cable, 5 ft. (1.5m)  
• RJ-45 to DB9 adapter for configuration cable  
• 2 mounting brackets and 4 screws  
• Quick-start guide  
Serial Ports - Connect either  
to Power Strip EIA-232 Port  
DCN Power Port  
Ethernet  
Port  
Sensor Sensor  
Serial  
2
Serial  
1
DCN  
Modem  
Ethernet  
2
1
Liebert OpenComms EM  
(EM PDU Controller)  
Mounting  
Bracket on  
either side  
Liebert MP  
Advanced  
Power Strip  
(MP-C5120)  
EIA-232  
EIA-232 Port  
1
2
3
4
5
6
8
8
POWER  
CONFIGURATION WITH OPENCOMMS EM  
1. Connect power to the DCN port on the OpenComms EM and to your MP Advanced Power Strip.  
2. Connect the six-wire end of the serial cable provided with the OpenComms EM to the EIA-232 port of  
your MP Advanced Power Strip.  
3. Connect the other end (eight-wire) of the serial cable to either Serial 1 or Serial 2 of the  
OpenComms EM.  
4. Connect a straight-through CAT5 Ethernet cable from your network to the Ethernet port on the back  
of the OpenComms EM.  
ASSIGN AN IP ADDRESS  
NOTE  
These steps must be done on the same network segment where the OpenComms EM is connected.  
If your network uses static IP addresses and your computer has a Windows operating system, follow the  
steps below. Otherwise, consult the OpenComms EM user manual (SL-28210).  
1. Obtain an IP address for the OpenComms EM from your network administrator.  
2. Insert the OpenComms EM CD in your computer’s CD drive.  
3. Click on the Start button, then on Run, then Browse to the file IPSET.exe on the CD and click  
Open.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONFIGURATION WITH LIEBERT MP ADVANCED ACCESS SERVER  
Liebert MP Advanced  
Power Strip  
(MP-C5120)  
Mounting  
Bracket on  
either side  
EIA-232  
EIA-232 Port  
1
2
3
4
5
6
8
8
POWER  
EIA-232 Port - Connect  
to Power Strip EIA-232 Port  
MP-DS74 Card With  
Configurable  
Communication Ports  
Ethernet Port  
Liebert MP Advanced  
Access Server  
(MP-S5138)  
100-240VAC  
??????????  
0.21-0.12AMPS  
On/Off Switch  
(not on all  
ROUTE  
LINE  
Access Servers)  
MADE IN USA  
MAKE CONNECTIONS  
1. Connect power to the Liebert MP Advanced Access Server and turn the unit On (the On/Off switch is  
on the rear of the unit; some units do not have this switch; they are energized whenever their power  
cord is plugged into a power source).  
2. Attach the adapter (RS-232 to RJ-45) to one end of a silver configuration cable (included) and connect  
that end of the cable to a COM port on a computer. Connect the other end of the cable to the EIA-232  
port of the MP-DS62 card on your MP Advanced Access Server.  
3. Plug one end of the second silver RJ-45 cable into any of the ports in the MP-DS74 module in your  
Liebert MP Advanced Access Server; plug the other end of the cable into the EIA-232 port on your MP  
Advanced Power Strip.  
HYPERTERMINAL SETTINGS  
ESTABLISH COMMUNICATION WITH CARD  
1. Use terminal emulation software, such as HyperTerminal™, to open a  
Baud Rate: 9600  
Data Bits:  
Parity:  
Stop Bits:  
8
direct connection to the MP-DS62 card. Use the settings at right. Press  
Enter for the Main Menu, choose “C” and then “1” to configure the  
MP-DS62 port.  
None  
1
Flow Control: N/A  
2. Enter “8” for Network Port Configuration (below left), then “7,” then “N”  
to disable DHCP (below right).  
Enter “N”  
to disable  
DHCP  
Enter “7”  
to change  
DHCP setting  
Choose “8” to change  
Network Port  
Configuration  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET THE IP ADDRESS  
1. Select “1” to set the IP Address for Module 1. Enter an IP address (below). The address must be  
unique on your system (obtain this from your network administrator).  
2. Press Enter to return to the Network Port Configuration menu.  
Enter IP address  
3. Choose “2” to set the Subnet Mask for your system (obtain this from your network administrator).  
SET THE GATEWAY ADDRESS  
1. Return to the Network Port Configuration menu and choose “3” to set the Gateway Address (the IP  
address of your network router). Follow the prompts to exit HyperTerminal and save your changes.  
2. Verify that your settings are correct and were saved by using a command prompt to ping the  
MP-C/MP-S unit: Start>Run>CMD.  
3. At the command prompt enter:  
ping [IP address]  
4. Press “Enter.”  
Liebert Corporation  
1050 Dearborn Drive  
P.O. Box 29186  
Columbus, OH 43229  
Telephone: 1-800-877-9222  
Facsimile: 1-614-841-6022  
© 2005 Liebert Corporation  
® Liebert and the Liebert logo are registered trademarks of  
All rights reserved throughout the world. Specifications subject Liebert Corporation. All names referred to are trademarks or  
to change without notice.  
registered trademarks of their respective owners.  
SL-20812 (01/05) Rev. 1  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  

Krups Espresso Maker XP 4050 User Manual
LaCie Computer Drive Core 4 User Manual
LG Electronics Blood Glucose Meter 47WX50MF User Manual
LG Electronics Microwave Oven 3828W5U0529 User Manual
Loewe Flat Panel Television R 26 User Manual
Mad Catz Battery Charger 58630N MUG User Manual
Manitowoc Ice Ice Maker 7603323 User Manual
Master Lock Electric Heater WA 41 A User Manual
Maytag Clothes Dryer MGD5600TQ1 User Manual
MGE UPS Systems Switch STS 200A User Manual