Operator Guide
5622/5627
Copier Reference
your document management partner
Download from Www.Somanuals.com. All Manuals Search And Download.
Type for 2522/2527/2212/2712/5622/5627/Aficio 1022/1027
Printed in Japan
UE USA B027-6607
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual contains detailed instructions on the operation and maintenance of this machine. To get
maximum versatility from this machine all operators should carefully read and follow the instructions in
this manual. Please keep this manual in a handy place near the machine.
Please read the Safety Information before using this machine. It contains important information related
to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS.
Notes
Some illustrations may be slightly different from your machine.
Certain options may not be available in some countries. For details, please contact your local dealer.
Operator Safety
This machine is considered a class 1 laser device, safe for office/EDP use. The machine contains one
GaAIAs laser diode, 5-milliwatt, 760-800 nanometer wavelength for each emitter. Direct (or indirect re-
flected) eye contact with the laser beam might cause serious eye damage. Safety precautions and in-
terlock mechanisms have been designed to prevent any possible laser beam exposure to the operator.
Laser Safety:
The Center for Devices and Radiological Health (CDRH) prohibits the repair of laser-based optical unit
in the field. The optical housing unit can only be repaired in a factory or at a location with the requisite
equipment. The laser subsystem is replaceable in the field by a qualified Customer Engineer. The laser
chassis is not repairable in the field. Customer engineers are therefore directed to return all chassis
and laser subsystems to the factory or service depot when replacement or the optical subsystem is re-
quired.
Warning:
Use of controls or adjustment or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your ma-
chine before reading this manual. (For details, see p.1 “Machine Types”.)
•
•
Type 1: 22 copies/minute (81/2" × 11"K)
Type 2: 27 copies/minute (81/2" × 11"K)
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
120V, 60Hz, 12A or more
Please be sure to connect the power cord to a power source as above. For details about power source,
see p.209 “Power Connection”.
Download from Www.Somanuals.com. All Manuals Search And Download.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
c means STAND BY.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
When using your equipment, the following safety precautions should always be
followed.
Safety During Operation
In this manual, the following important symbols are used:
R WARNING:
Indicates a potentially hazardous situation which, if instructions
are not followed, could result in death or serious injury.
R CAUTION:
Indicates a potentially hazardous situation which, if instructions are not
followed, may result in minor or moderate injury or damage to property.
R WARNING:
• Connect the power cord directly into a wall outlet and never use an ex-
tension cord.
• Disconnect the power plug (by pulling the plug, not the cable) if the
power cable or plug becomes frayed or otherwise damaged.
• To avoid hazardous electric shock or laser radiation exposure, do not
remove any covers or screws other than those specified in this manu-
al.
• Turn off the power and disconnect the power plug (by pulling the plug,
not the cable) if any of the following conditions exists:
• You spill something into the equipment.
• You suspect that your equipment needs service or repair.
• Your equipment's cover has been damaged.
• Do not incinerate spilled toner or used toner. Toner dust might ignite
when exposed to an open flame.
• Disposal can take place at our authorized dealer or at appropriate col-
lection sites.
• Dispose of the used toner bottle in accordance with the local regula-
tion.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
R CAUTION:
• Protect the equipment from dampness or wet weather, such as rain, snow,
and so on.
• Unplug the power cord from the wall outlet before you move the equipment.
While moving the equipment, you should take care that the power cord will
not be damaged under the equipment.
• When you disconnect the power plug from the wall outlet, always pull the
plug (not the cable).
• Do not allow paper clips, staples, or other small metallic objects to fall inside
the equipment.
• Keep toner (used or unused) and toner bottle out of the reach of children.
• For environmental reasons, do not dispose of the equipment or expended
supply waste at household waste collection points. Disposal can take place
at an authorized dealer or at appropriate collection sites.
• The inside of the machine could be very hot. Do not touch the parts with a
label indicating the “hot surface”. Otherwise it could cause a personal burn.
• Our products are engineered to meet high standards of quality and function-
ality, and we recommend that you only use the expendable supplies availa-
ble at an authorized dealer.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read this Manual
Symbols
In this manual, the following symbols are used:
R WARNING:
This symbol indicates a potentially hazardous situation that might result in
death or serious injury when you misuse the machine without following the in-
structions under this symbol. Be sure to read the instructions, all of which are in-
cluded in the Safety Information section.
R CAUTION:
This symbol indicates a potentially hazardous situation that might result in mi-
nor or moderate injury or property damage that does not involve personal injury
when you misuse the machine without following the instructions under this
symbol. Be sure to read the instructions, all of which are included in the Safety
Information section.
• WARNINGS and CAUTIONS are notes for your safety.
Important
If this instruction is not followed, paper might be misfeed, originals might be
damaged, or data might be lost. Be sure to read this.
Preparation
This symbol indicates the prior knowledge or preparations required before op-
erating.
Note
This symbol indicates precautions for operation or actions to take after misoper-
ation.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions in which a particular function cannot be used.
Reference
This symbol indicates a reference.
[
]
Keys that appear on the machine's display panel.
{
}
Keys built into the machine's control panel.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Machine Types............................................................................................ 1
What You Can Do with This Machine (Copy Mode)................................. 2
Guide To Components............................................................................... 5
Options........................................................................................................ 7
Control Panel .............................................................................................. 8
Display Panel ............................................................................................ 10
Displays and Key Operations....................................................................... 10
Function List Based on Options ............................................................. 12
1.Basics
Turning On the Power.............................................................................. 15
Turning On the Main Power ......................................................................... 15
Turning On the Power .................................................................................. 16
Turning Off the Power .................................................................................. 16
Changing Modes....................................................................................... 17
Originals.................................................................................................... 18
Sizes and Weights of Recommended Originals........................................... 18
Sizes Detectable by the Auto Paper Select ................................................. 20
Missing Image Area ..................................................................................... 21
Copy Paper................................................................................................ 22
Recommended Paper Sizes and Types....................................................... 22
Direction-fixed paper or 2-sided paper......................................................... 25
Non-recommended Paper............................................................................ 26
Paper Storage .............................................................................................. 26
Toner.......................................................................................................... 27
Handling Toner............................................................................................. 27
Toner Storage .............................................................................................. 27
Used Toner .................................................................................................. 27
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
2.Copying
Basic Procedure ....................................................................................... 29
Placing Originals ...................................................................................... 31
Placing Originals on the Exposure Glass..................................................... 31
Placing Originals in the Document Feeder................................................... 32
Placing a Stack of Originals in the Document Feeder.................................. 32
Original Orientation ...................................................................................... 33
Placing Special Originals ............................................................................. 34
Placing Custom Size Originals..................................................................... 36
Basic Functions........................................................................................ 38
Adjusting Copy Image Density ..................................................................... 38
Selecting Original Type Setting.................................................................... 40
Selecting Copy Paper .................................................................................. 41
Auto Reduce/Enlarge................................................................................... 44
Sort/Stack/Staple...................................................................................... 45
Sort............................................................................................................... 47
Stack ............................................................................................................ 49
Staple........................................................................................................... 51
To Stop Scanning Temporarily..................................................................... 56
When Memory Reaches 0% ........................................................................ 56
To Remove Paper from the Staple Unit ....................................................... 56
Copying from the Paper Tray 2 ............................................................... 57
Using Tray 2 as Bypass Tray....................................................................... 57
Copying from the Bypass Tray ............................................................... 61
Programs................................................................................................... 67
Storing a Program ........................................................................................ 67
Deleting a Program ...................................................................................... 69
Recalling a Program..................................................................................... 69
Job Preset ................................................................................................. 70
Other Functions........................................................................................ 71
Energy Saver Mode ..................................................................................... 71
Interrupt Copy .............................................................................................. 71
Original Beeper ............................................................................................ 72
Sample Copy................................................................................................ 72
Changing the Number of Sets...................................................................... 73
Preset Reduce/Enlarge ............................................................................ 74
Create Margin Mode .................................................................................... 76
Zoom.......................................................................................................... 77
Size Magnification .................................................................................... 79
Directional Magnification (%) .................................................................. 81
Directional Size Magnification (Inch)...................................................... 83
Duplex/Combine/Series ........................................................................... 85
Original Direction and Completed Copies .................................................... 86
Originals and Copy Direction ....................................................................... 86
Specifying Orientation of Bound Originals ................................................... 86
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Duplex........................................................................................................ 88
1 Sided → 2 Sided ....................................................................................... 88
2 Sided → 2 Sided ....................................................................................... 89
Combine .................................................................................................... 91
1 Sided 2 Pages → Combine 1 Side............................................................ 92
1 Sided 4 Pages → Combine 1 Side............................................................ 93
1 Sided 8 Pages → Combine 1 Side............................................................ 94
1 Sided 4 Pages → Combine 2 Side............................................................ 95
1 Sided 8 Pages → Combine 2 Side............................................................ 96
1 Sided 16 Pages → Combine 2 Side.......................................................... 97
2 Sided 2 Pages → Combine 1 Side............................................................ 98
2 Sided 4 Pages → Combine 1 Side............................................................ 99
2 Sided 8 Pages → Combine 1 Side.......................................................... 100
2 Sided 4 Pages → Combine 2 Side.......................................................... 101
2 Sided 8 Pages → Combine 2 Side.......................................................... 102
2 Sided 16 Pages → Combine 2 Side........................................................ 103
Series/Book............................................................................................. 105
Series Copies............................................................................................. 105
Copying Book Originals.............................................................................. 109
Edit Image ............................................................................................... 115
Image Repeat............................................................................................. 115
Double Copies............................................................................................ 116
Centering.................................................................................................... 117
Positive/Negative ....................................................................................... 118
Erase........................................................................................................ 119
Border Erase .............................................................................................. 120
Center Erase .............................................................................................. 121
Center/Border Erase .................................................................................. 122
Margin Adjustment................................................................................. 124
Stamp....................................................................................................... 126
Background Numbering ............................................................................. 126
Preset Stamp ............................................................................................. 127
User Stamp ................................................................................................ 129
Program/Delete User Stamp ...................................................................... 131
Date Stamp ................................................................................................ 133
Page Numbering ........................................................................................ 136
Cover/Slip Sheet..................................................................................... 142
Front Cover ................................................................................................ 142
Front/Back Covers ..................................................................................... 144
Designate................................................................................................... 145
Chapter ...................................................................................................... 147
Slip Sheets .............................................................................................. 149
Storing Originals in the Document Server........................................... 151
Combination Chart ................................................................................. 152
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
3.Troubleshooting
If Your Machine Does Not Operate as You Want................................. 153
General ...................................................................................................... 153
Document Server ....................................................................................... 154
Display ....................................................................................................... 155
If You Cannot Make Clear Copies ......................................................... 156
If You Cannot Make Copies As You Want............................................ 157
General ...................................................................................................... 157
Adjust Image .............................................................................................. 157
Stamp......................................................................................................... 158
Combine..................................................................................................... 158
Duplex ........................................................................................................ 159
When Memory Is Full ................................................................................. 159
B Loading Paper ................................................................................... 160
Loading Paper in Tray 1-4.......................................................................... 160
Loading Paper in the Large Capacity Tray................................................. 161
D Adding Toner ..................................................................................... 162
x Clearing Misfeeds.............................................................................. 164
Changing the Paper Size ....................................................................... 170
Changing the Paper Size in Tray 1-4/Paper Tray Unit............................... 170
d Adding Staples .................................................................................. 172
500-Sheet Finisher..................................................................................... 172
1000-Sheet Finisher................................................................................... 173
e Removing Jammed Staples .............................................................. 175
500-Sheet Finisher..................................................................................... 175
1000-Sheet Finisher................................................................................... 176
4.User Tools (Copy/Document Server Features)
Accessing the User Tools (Copy/Document Server Features) .......... 179
Exiting From the User Tools....................................................................... 180
User Tools Menu (Copier/Document Server Features)....................... 182
1
General Features / ............................................................................... 184
4
2
General Features / ............................................................................... 187
4
3
General Features / ............................................................................... 189
4
4
General Features / ............................................................................... 190
4
1
Reproduction Ratio / ........................................................................... 191
2
2
Reproduction Ratio / ........................................................................... 192
2
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Edit / ...................................................................................................... 194
2
2
Edit / ...................................................................................................... 196
2
Stamp....................................................................................................... 199
Background Numbering ............................................................................. 199
1
4
Preset Stamp / - / ................................................................................... 199
4
2
4
1
User Stamp / - / ...................................................................................... 200
2
2
Date Stamp ................................................................................................ 201
1
2
Page Numbering / - / .............................................................................. 202
2
2
Input/Output............................................................................................ 204
5.REMARKS
Do's And Don'ts...................................................................................... 207
Where to Put Your Machine................................................................... 208
Machine Environment ................................................................................ 208
Moving........................................................................................................ 208
Power Connection...................................................................................... 209
Access to the Machine............................................................................... 209
Maintaining Your Machine..................................................................... 210
Cleaning the Exposure Glass..................................................................... 210
Cleaning the Exposure Glass Cover.......................................................... 210
Cleaning the Document Feeder ................................................................. 210
Replacing Photo Conductor Unit (PCU) .............................................. 211
6.Specification
Mainframe................................................................................................ 217
Document Feeder (Option) .................................................................... 222
500-Sheet Finisher (Option)................................................................... 223
1000-Sheet Finisher (Option)................................................................. 224
Shift Sort Tray (Option).......................................................................... 226
Duplex Unit (Option)............................................................................... 227
Internal tray 2 (1 bin tray) (Option)........................................................ 228
Bypass Tray (Option) ............................................................................. 229
Large Capacity Tray (LCT) (Option)...................................................... 230
Paper tray unit (Option) ......................................................................... 231
INDEX....................................................................................................... 232
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine Types
This machine comes in two models which vary by copy speed. To make sure
which model you have, see the inside front cover.
Type 1
Type 2
Copy speed
22 copies/minute
(A4K, 81/2" × 11"K)
27 copies/minute
(A4K, 81/2" × 11"K)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
What You Can Do with This Machine (Copy
Mode)
Note
❒ The reference of each function is on the next page of this illustration.
*3
*1
Positive/Negative
2
Download from Www.Somanuals.com. All Manuals Search And Download.
*2
*2
Series/Book
*4
Document Server
*1
*1
Front & Back
*1
1 Sided & Booklet
*1
*1
2 Sided & Booklet
*1
2 Sided & Magazine
*1
1 Sided & Magazine
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. “Selecting Original Type Setting”
22. “2 Sided 4 Pages → Combine 2
⇒ p.40
Side” ⇒ p.101
2. “Adjusting Copy Image Density”
23. “2 Sided 8 Pages → Combine 2
⇒ p.38
Side” ⇒ p.102
3. “Placing Special Originals” ⇒
24. “2 Sided 16 Pages → Combine 2
p.34
Side” ⇒ p.103
4. “Image Repeat” ⇒ p.115
5. “Double Copies” ⇒ p.116
6. “Centering” ⇒ p.117
25. “Book → 1 Sided” ⇒ p.105
26. “Book → 2 Sided” ⇒ p.106
27. “Front & Back → 2 Sided” ⇒
p.107
7. “Erase” ⇒ p.119
28. “1 Sided → Booklet” ⇒ p.109
29. “2 Sided → Booklet” ⇒ p.110
30. “1 Sided → Magazine” ⇒ p.112
31. “2 Sided → Magazine” ⇒ p.113
32. “Preset Reduce/Enlarge” ⇒ p.74
33. “Zoom” ⇒ p.77
8. “Margin Adjustment” ⇒ p.124
9. “Positive/Negative” ⇒ p.118
10. “Stamp” ⇒ p.126
11. “1 Sided → 2 Sided” ⇒ p.88
12. “2 Sided → 2 Sided” ⇒ p.89
13. “1 Sided 2 Pages → Combine 1
Side” ⇒ p.92
34. “Size Magnification” ⇒ p.79
14. “1 Sided 4 Pages → Combine 1
35. “Directional Magnification (%)”
Side” ⇒ p.93
⇒ p.81
15. “1 Sided 8 Pages → Combine 1
36. “Directional Size Magnification
Side” ⇒ p.94
(Inch)” ⇒ p.83
16. “2 Sided 2 Pages → Combine 1
37. “Document Server” ⇒ p.154
38. “Sort” ⇒ p.47
39. “Rotate Sort” ⇒ p.47
40. “Stack” ⇒ p.49
Side” ⇒ p.98
17. “2 Sided 4 Pages → Combine 1
Side” ⇒ p.99
18. “2 Sided 8 Pages → Combine 1
41. “Staple” ⇒ p.51
Side” ⇒ p.100
42. “Front Cover” ⇒ p.142
43. “Front/Back Covers” ⇒ p.144
44. “Designate” ⇒ p.145
45. “Chapter” ⇒ p.147
46. “Slip Sheets” ⇒ p.149
47. “Auto Reduce/Enlarge” ⇒ p.44
19. “1 Sided 4 Pages → Combine 2
Side” ⇒ p.95
20. “1 Sided 8 Pages → Combine 2
Side” ⇒ p.96
21. “1 Sided 16 Pages → Combine 2
Side” ⇒ p.97
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide To Components
1. Exposure glass cover (option) or
5. Main power switch
Document feeder (ADF) (option)
If the machine does not operate after
turning on the operation switch, check if
the main power switch is turned on. If it
is off, turn it on.
Lower the exposure glass cover over
originals placed on the exposure glass for
copying. If you have the document feed-
er, load a stack of originals here. They
will be fed automatically one by one.
(The illustration shows the document
feeder.)
6. Main power indicator
This indicator lights up when the main
power switch is turned on and goes off
when the switch is turned off.
2. Exposure glass
7. On indicator
Place originals face down here for copy-
This indicator lights up when the opera-
tion switch is turned on and goes off
when the switch is turned off.
ing. ⇒ p.18 “Originals”
3. Internal tray
Copied paper is delivered here face
down.
8. Operation switch
Press this switch to turn the power on
(the On indicator lights up). To turn the
power off, press this switch again (the On
indicator goes off).
4. Ventilation holes
Prevents overheating. Do not obstruct
the ventilation holes by placing an object
near it or leaning an object against it. If
the machine overheats, a fault might oc-
cur.
9. Control panel
⇒ p.8 “Control Panel”
5
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Remove Paper Indicator
13. Paper tray
The indicator is lit when paper is output
to the internal tray 2 (1 bin tray). When
paper is removed from the internal tray 2,
the indicator goes off.
Load paper here. ⇒ p.160 “B Loading
Paper”
14. Paper tray 2
Use when copying onto OHP transparen-
cies, label paper (adhesive labels), trans-
lucent paper, postcards, envelopes and
non-standard size paper. ⇒ p.57 “Copy-
ing from the Paper Tray 2”
Note
❒ Internal tray 2 (1 bin tray) is optional.
11. Duplex unit (Unit for two-sided
copies) (option)
Makes two-sided copies.
15. Paper tray unit (option)
Load paper here. ⇒ p.160 “B Loading
12. Front cover
Open to access the inside of the machine.
Paper”
1. Bypass tray (option)
2. Paper tray cover
Use when copying onto OHP transparen-
cies, label paper (adhesive labels), trans-
lucent paper, postcards, envelopes and
non-standard size paper. ⇒ p.61 “Copy-
ing from the Bypass Tray”
Open this cover to remove jammed pa-
per.
3. Lower right cover
Open this cover to remove jammed pa-
per.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
1. 500-Sheet Finisher
Sorts, stacks and staples the copies.
7. Shift sort tray
Sorts and stacks the copies.
2. Bridge unit
Relays copies to the finisher.
8. Paper tray unit
Consists of two paper trays.
3. Exposure glass cover
9. Large Capacity Tray (LCT)
Lower this cover over originals for copy-
ing.
Holds 2000 sheets of paper.
10. Bypass tray
4. Document feeder (ADF)
Load a stack of originals here. They will
be fed automatically.
Use when copying onto OHP transparen-
cies, label paper (adhesive labels), trans-
lucent paper, postcards, envelopes and
non-standard size paper. ⇒ p.61 “Copy-
ing from the Bypass Tray”
5. Internal tray 2 (1 bin tray)
If you select this as the output tray, cop-
ied paper will be delivered here face
down.
11. Duplex unit
Use to make two-sided copies.
6. 1000-Sheet Finisher
12. Inter change unit
Required when installing the internal
tray 2 (1 bin tray) and duplex unit.
Sorts, stacks and staples the copies.
*1
: Finisher proof tray
*2
: Finisher shift tray
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel
1. Screen Contrast knob
7. {Clear Modes} key
Adjusts the brightness of the display panel.
Press to clear the previously entered copy
job settings.
2. Indicators
These indicators show the status of the
machine or indicate errors. ⇒ p.153
“Troubleshooting”
8. {Energy Saver} key
Press to switch to and from the Energy
Saver mode. ⇒ p.71 “Energy Saver
Mode”
3. {User Tools/Counter} key
• User Tools
9. {Interrupt} key
Press to interrupt a long copy job to make
Press to change the default settings
and conditions to meet your require-
ments. ⇒ p.179 “User Tools
(Copy/Document Server Features)”
copies. ⇒ p.71 “Interrupt Copy”
10. Main power indicator
This indicator goes on when the main
power switch is turned on and goes off
when the switch is turned off.
• Counter
Press to check or print the total
number of copies made.
• Inquiry
11. Operation switch
Shows where to order expendable
supplies and where to call when a
malfunction occurs. You can also print
these details.
Press this switch to turn the power on
(the On indicator goes on). To turn the
power off, press this switch again (the On
indicator goes off).
4. Display panel
Shows operation status, error messages,
and function menus. ⇒ p.10 “Display
Panel”
12. {Sample Copy} key
Use this key to make a single sample
copy before starting a long copy run. By
checking the sample copy and making
any necessary changes to the image qual-
ity settings before you make multiple
copies, you can save time and paper. ⇒
p.72 “Sample Copy”
5. {Check Modes} key
Press to check the entered copy job set-
tings.
6. {Program} key
Press to select the program mode. ⇒ p.67
“Programs”
8
Download from Www.Somanuals.com. All Manuals Search And Download.
13. {Start}
key
Press to start copying. Press to start scan-
ning and printing in Document Server
mode.
14. {Clear/Stop} key
• Clear
Press to delete a number entered.
• Stop
Press to stop a copy job in progress.
15. {#} key
Press to enter a value.
16. Number keys
Use to enter the desired number of copies
and data for selected modes.
17. Function keys
Press the appropriate key to choose any
of the following functions:
• Copy
• Document Server
• Facsimile
• Printer
• Scanner
18. Function Status indicator
These show the status of the above func-
tions:
• Yellow: the function is selected
• Green: the function is active
• Red: the function has been interrupted
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Panel
The display panel shows the status of the machine, error messages and function
menus.
Important
❒ Do not apply a strong shock or force of about 30 N (about 3 kgf) or more to
the display panel. If you do, the display might be damaged.
Note
❒ The function items displayed serve as selector keys. You can select or specify
an item by lightly pressing it.
❒ When you select or specify an item on the display panel, it is highlighted like
.
OK
❒ Keys appearing as
cannot be used.
Displays and Key Operations
Note
❒ The following illustrations are examples for a machine with the optional
1000-sheet finisher installed.
❖
Initial copy display
1. Original mode, Image Density
4. The number of originals scanned
into memory, number of copies set,
and number of copies made
and Special Original mode
2. Operational status or messages
5. Sort, Stack or Staple mode
3. You can register up to three fre-
quently used reduce/enlarge ratios
other than the fixed reduce/enlarge
ratios. ⇒ "Shortcut R/E" on p.191
“Reproduction Ratio 1/2”
6. Displays the contents of the
Shortcut keys. You can register fre-
quently used functions in these
keys. ⇒ "Copy Function Key F1-F5"
on p.189 “General Features 3/4”
10
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Shows the available functions.
Press a function name to display its
menu. For example, press the [Re-
duce/Enlarge] key to bring up the Re-
duce/Enlarge menu.
8. A clip mark appears for a current-
ly selected function.
❖
Function menu
1. Items you can select.
2. The key highlighted indicates the
selected paper tray, and the key with
the lower line blinking indicates the
tray feeding the paper.
❖
Document Server initial display
1. Operational status and messages
4. Operational keys
2. Display titles
5. Documents sent by fax
3. The number of originals scanned
into memory, number of copies set,
and number of copies made
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Function List Based on Options
The functions that are available to you depend on your machine configuration
and which options you have. See the table below.
❍…Available
×…Not available
Type 1
Type 2
Place originals
on the expo- in the docu-
sure glass
ment feeder
*7
*7
Document Feeder
❍
❍
—
❍
Mixed Sizes of the Same Width
Mode
Custom Size Originals
❍
❍
❍
❍
❍
❍
❍
❍
Original Orientation (Standard
Orientation)
Auto Image Density
Manual Image Density
Auto Paper Select
Manual Paper Select
Copying from the Bypass Tray
Sample Copy/Job Preset
Auto Reduce/Enlarge
Reduce/Enlarge
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
*5
*5
*5
*5
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
Create Margin Mode
Book
*6
*6
Duplex
❍
❍
Combine
1 Sided 2 pages, 4
pages, 8 pages, → 1
Side
❍
❍
*6
*6
1 Sided 4 pages, 8
pages, 16 pages, →
2 Side
❍
❍
❍
❍
❍
❍
❍
❍
2 Sided 2 pages, 4
pages, 8 pages, → 1
Side
❍
❍
*6
*6
2 Sided 4 pages, 8
pages, 16 pages, →
2 Side
❍
❍
Series
Book → 1 Sided
❍
❍
❍
❍
❍
×
×
×
*6
*6
Book → 2 Sided
❍
❍
*6
*6
Front & Back → 2
Sided
❍
❍
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Type 1
Type 2
Place originals
on the expo- in the docu-
sure glass
ment feeder
*6
*6
Copying Book Originals
Image Repeat
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
Double Copies
Centering
Positive/Negative
Border Erase/Center Erase
Margin Adjustment
Background Numbering
Preset Stamp
❍
❍
*8 *9
*8 *9
*8 *9
*8 *9
*8 *9
*8 *9
User Stamp
Date Stamp/Page Numbering
❍
❍
❍
❍
Cover/Front/Back Cover/Slip
Sheet
Sort
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
*3
*3
Shift Sort
Rotate Sort
Shift Stack
Staple
*1 *2
*3
*1 *2
*3
*4
*4
*9
*9
Store File
❍
❍
*1
*2
*3
Set the paper of the same size KL in the paper trays.
You can use this function when "Rotate Sort" is selected in "Select Stack Function".
500-sheet Finisher or 1000-sheet Finisher and Bridge unit; or Shift sort tray is re-
quired.
*4
*5
*6
500-sheet Finisher or 1000-sheet Finisher and Bridge unit is required.
Bypass tray is required.
Duplex unit and Inter change unit is required. 32 MB Memory or HDD is also re-
quired for certain types of originals.
Document feeder is required.
32 MB Memory is required. (If the machine is equipped with the Printer unit, 32 MB
memory is not required.)
HDD is required.
*7
*8
*9
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Basics
Turning On the Power
To turn the machine on, press the op-
eration switch.
Turning On the Main Power
Note
A Make sure that the power cord is
firmly plugged into the wall out-
let.
❒ This machine automatically enters
Energy Saver mode or turns itself
off if you do not use the machine
for a while. See p.30 “Auto Off”
and "Timer Setting" in the System
Settings manual.
B Open the switch cover and turn
on the main power switch. The
Main Power indicator goes on.
-Power switches
This machine has two power switch-
es. ⇒ p.10 “Display Panel”
❖
Operation switch (right side of the
control panel)
Press this switch to activate the
machine. When the machine has
warmed up, you can make copies.
Important
❖
Main power switch (front of the ma-
chine)
When the machine is not to be used
for an extended period of time,
turn off the main power switch.
❒ Do not switch off the main pow-
er immediately after it has been
switched on. Failure to observe
this may result in damage to the
hard disk or memory, leading to
malfunctions.
❒ You can use the machine within
15 seconds after the main power
switch has been turned on.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Note
Turning On the Power
❒ In the following cases, even if
you press the operation switch,
the indicator will not go off but
blink:
A Press the operation switch. The
On indicator goes on.
1
The display panel will come on.
• When the exposure glass
cover or document feeder is
open
• When communication is in
progress with external
equipment
• When the hard disk is oper-
ating
Turning Off the Main Power
Note
A Make sure that the On indicator is
❒ If the power is not turned on
when the operation switch is
pressed, check if the main pow-
er switch is on. If off, turn it on.
off.
B Turn off the main power switch.
The Main Power indicator goes
off.
❒ During the warm-up period
(less than 10 seconds), you can
use the Auto Start function.
Important
❒ Do not turn off the main power
switch when the On indicator is
lit or blinking. This might dam-
age the hard disk or memory
and cause malfunctions.
Turning Off the Power
A Make sure that the exposure glass
cover or document feeder is
closed.
❒
Pull out the power plug after you
turn off the main power switch.
If you do not, the hard disk or
memory might be damaged. This
could cause malfunctions.
B Press the operation switch. The
On indicator goes off.
❒ Make sure 100% is displayed for
the remaining memory space in
facsimile mode before turning
off the main power or unplug-
ging the power cord. If the main
power switch is turned off or
the power cord is disconnected,
any documents stored in fax
memory will be lost after ap-
proximately one hour. ⇒Chap-
ter 10, "When Power is Turned
off or Fails" in Advanced Fea-
tures manual of Fax Reference
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Modes
Changing Modes
You can use this machine not only as a copier, but also as a fax, printer, docu-
ment server and scanner as well. Press the {Copy}, {Facsimile}, {Printer}, {Scan-
ner} or {Document Server} key to use that function.
1
Limitation
❒ You cannot switch modes in the following cases:
• During interrupt copying
• When scanning in a fax message for transmission
• During immediate transmission
• During On-hook dialing for fax transmission
• While scanning an original
• When accessing the user tools
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Originals
Sizes and Weights of Recommended Originals
1
❖
Metric version
Where Original Is Placed Original Size
Original Weight
Exposure glass
Up to A3
--
40 – 128g/m2
Document feeder
1-sided originals:
A3L – A5KL
52 – 105g/m2
2-sided originals:
A3L – A5KL
❖
Inch version
Where Original Is Placed Original Size
Original Weight
Exposure glass
Up to 11" × 17"
--
Document feeder
1-sided originals:
11 – 34 lb.
11" × 17"L – 51/2" × 81/2"KL
2-sided originals:
14 – 28 lb.
11" × 17"L – 51/2" × 81/2"KL
Note
❒ The number of originals that can be placed in the document feeder is about 50.
❒ The weight range for originals in the Mixed Size mode is 52-81g/m2, 13.8-21.5
lb.
❒ Make sure the original is placed correctly so that it is fed straight.
❒ When placing paper 433mm or larger in the document feeder (ADF), there are
cases when the paper will be jammed, creased, or not fed.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Originals
Non-recommended originals for the document feeder
Placing the following types of originals in the document feeder can cause paper
misfeeds or result in damage to the originals. Place these originals on the expo-
sure glass instead.
1
• Originals other than those specified in ⇒ p.18 “Sizes and Weights of Recom-
mended Originals”
• Stapled or clipped originals
• Perforated or torn originals
• Curled, folded, or creased originals
• Pasted originals
• Originals with any kind of coating, such as thermal fax paper, art paper, alu-
minum foil, carbon paper, or conductive paper
• Originals with perforated lines
• Originals with indexes, tags, or other projecting parts
• Sticky originals such as translucent paper
• Thin originals that have low stiffness
• Thick originals such as postcards
• Originals of inappropriate weight
• Bound originals such as books
• Transparent originals such as OHP transparencies or translucent paper
• Originals that have correction fluid or ink on them that has not completely
dried
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Sizes Detectable by the Auto Paper Select
❖
Metric version
1
81/2"
14"
×
81/2"
×
51/2"
81/2"
KL
×
81/2"
×
Size A3L B4L A4K B5K A5K 11" ×
L
L
L
17"L
L
11"K
13"
L
Location
*1
L
of the
original
Exposure
glass
❍
❍
❍
❍
❍
❍
×
×
×
❍
×
×
×
❍
Document
feeder
❍
❍
❍
×
×
×
*1
You can select from 81/2" × 13",81/4" × 13" or 8" × 13" with the User Tools (System Set-
tings). See "<F/F4>Size Setting"in the System Settings manual.
❖
Inch version
81/2" 81/2" 51/2" 81/2"
8" × 10" ×
Size A3
L
B4L A4
B5K A5
11" ×
KL L
KL 17"
L
10"
L
14"
L
× 14" × 11"
×
× 13"
L
Location
of the
81/2"
KL
L
KL
original
Exposure
glass
×
×
×
×
×
×
×
×
❍
❍
❍
❍
×
×
×
❍
❍
❍
Document
feeder
×
×
❍
❍
❍
×
Sizes difficult to detect
It is difficult for the machine to detect the sizes of the following originals, so se-
lect the paper size manually.
• Originals with indexes, tags, or other projecting parts
• Transparent originals such as OHP transparencies or translucent paper
• Dark originals with a lot of text and drawings
• Originals which partially contain a solid image
• Originals which have solid images at their edges
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Originals
Missing Image Area
❖
Exposure glass
1
Reference
position
A3
Horizontal size
Maximum Scanning area
A3 (297x420mm)
11"x17" (279x432mm)
A4 A3
CP01AEE
❖
Document feeder
Limitation
❒ Even if you correctly place originals in the document feeder or on the expo-
sure glass, 3mm (0.1") margins on all four sides of the original might not be
copied.
❒ Make sure the original is placed correctly so that it is fed straight.
❒ When placing paper 433mm or larger in the document feeder (ADF), there are
cases when the paper will be jammed, creased, or not fed.
❒ The maximum value for the system length setting is 1260mm (49").
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Copy Paper
Recommended Paper Sizes and Types
1
The following limitations apply to each tray:
Tray
Type
Paper Type and
Weight
Metric Version
Inch Version
Paper
Capacity
Tray 1 60-90g/m2
A3L, B4L, A4KL, B5KL, A5L
500 sheets
*10
(16-24lb.)
*1
Paper
Tray
11" ×17"L, 81/2" × 14"L, 81/2" × 11"KL,
8" × 13"L, 81/2" × 13"L, 81/4" × 13"L, 81/4" × 14"L,
11" × 14"L, 71/4" × 101/2"K, 8" × 101/2"KL,
51/2" × 81/2"L, 8KL, 16KKL
Unit *10
(option)
*2
*2
Custom size
Vertical: 140-297 mm
Custom size
Vertical: 5.6"-11.7"
Horizontal: 182-432 mm Horizontal: 7.3"-17.0"
Tray 2 60-90g/m2
A3L, B4L, A4KL, B5KL, A5L
500 sheets
*10
(16-24lb.)
B6L, A6L, 11" × 17"L, 81/2" × 14"L, 81/2" ×
*1
11"KL, 51/2" × 81/2"L, 71/4" × 101/2" KL, 8" ×
13"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 10"KL,
81/4" × 14"L, 11" × 14"L, 8" × 101/2"KL, 11" ×
15"L, 10" × 14"L, 10" × 15"L, 8KL, 16KKL
Thin paper
52-60g/m2
(14-16lb.)
*2
*2
Custom size
Vertical: 100-297 mm
Custom size
Vertical: 4.0"-11.7"
Horizontal: 148-432 mm Horizontal: 5.9"-17.0"
*7
Thick paper *11
A3L, B4L, A4KL, B5KL, A5L
105-157g/m2
(28-42lb.)
*1
B6L, A6L, 11" × 17"L, 81/2" × 14"L, 81/2" ×
11"KL, 51/2" × 81/2"L, 71/4" × 101/2" KL, 8" ×
13"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 10"KL,
81/4" × 14"L, 11" × 14"L, 8" × 101/2"KL, 11" ×
15"L, 10" × 14"L, 10" × 15"L, 8KL, 16KKL
*2
*2
Custom size
Vertical: 100-297 mm
Horizontal: 148-432 mm Horizontal: 5.9"-17.0"
Custom size
Vertical: 4.0"-11.7"
Translucent paper A3L, B4L, A4KL, B5KL
OHP transparencies A4KL
Postcards
100 × 148 mm
Label paper
B4L, A4L
(adhesive labels)
Envelope
37/8" × 71/2"L, 41/8" × 91/2"L, C5 EnvL,
C6 EnvL, DL EnvL
–
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Copy Paper
Tray
Type
Paper Type and
Weight
Metric Version
Inch Version
Paper
Capacity
Bypass 52-90g/m2
A3L, B4L, 11" × 17"L, 81/2" × 14"L, 8" × 13"L,
81/2" × 13"L, 81/4" × 13"L, 81/4" × 14"L, 11" ×
14"L, 11" × 15"L, 10" × 14"L, 10" × 15"L, 8KL
10 sheets
Tray *10 (14-24lb.)
(option)
Thin paper
1
52-60g/m2
(14-16lb.)
A4KL, B5KL, A5KL, B6L
100 sheets
A6L, 81/2" × 11"KL, 51/2" × 81/2"L, 71/4" ×
*3
101/2"LK, 8" × 10"KL, 8" × 101/2"KL, 16KKL
*4
*4
*8
Custom size
Custom size
Vertical: 90-305 mm
Horizontal: 148-432 mm *12
Vertical: 3.6"-12.0"
Horizontal: 5.9"-17.0" *12
Thick paper *11
105-157g/m2
(28-42lb.)
A3L, B4L, 11" × 17"L, 81/2" × 14"L, 8" × 13"L,
81/2" × 13"L, 81/4" × 13"L, 81/4" × 14"L, 11" ×
14"L, 11" × 15"L, 10" × 14"L, 10" × 15"L, 8KL
10 sheets
40 sheets
A4KL, B5KL, A5KL, B6L
*3
A6L, 81/2" × 11"KL, 51/2" × 81/2"L, 71/4" ×
101/2"KL, 8" × 10"KL, 8" × 101/2"KL, 16KKL
*4
*4
*9
Custom size
Vertical: 90-305 mm
Horizontal: 148-432 mm *12 Horizontal: 5.9"-17.0" *12
Translucent paper A3L, B4L
A4KL, B5KL
Custom size
Vertical: 3.6"-12.0"
10 sheets
40 sheets
*5
OHP transparencies A4KL
10 sheets
*5
Postcards
100 × 148 mm
40 sheets
*5
Label paper (adhe- B4L, A4L
1 sheet
sive labels)
Envelope
37/8" × 71/2"L, 41/8" × 91/2"L, C5 EnvL,
C6 EnvL, DL EnvL
–
Large
Capaci-
ty Tray
60-90g/m2 A4K, 81/2" × 11"K *6
(16-24lb.)
2000
(1000 +
1000)
sheets
(LCT)
*10
(option)
*1
*2
*3
Set the paper size selector to the p mark, and then select the paper size in System
Settings. ⇒ "Paper Size Setting" in the System Settings manual
Set the paper size selector to the p mark, and then specify the paper size. ⇒ p.57
“Copying from the Paper Tray 2”
Place the paper in the bypass tray, and select the paper size. ⇒ p.62 “When copying
onto standard size paper”
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
*4
Place the paper in the bypass tray, and specify the paper size. ⇒ p.63 “When copying
onto custom size paper”
When paper larger than 433mm is used, there are cases when the paper will be
jammed, creased, or not fed. Make sure the paper is placed correctly so that it is fed
straight.
*5
*6
It is recommended to place one sheet at a time.
1
The paper tray fence is fixed. If you wish to change the size of paper placed in this
tray, contact your service representative.
*7
When loading paper, make sure that the stack height does not exceed the lower limit
mark of the paper tray 2. ⇒ p.160 “Setting special paper in the Paper Tray 2”
When the paper size is larger than A4L, you can load 10 sheets.
When the paper size is smaller than A4L, you can load 100 sheets.
When the thick paper size is larger than A4L, you can load 10 sheets.When the thick
paper size is smaller than A4L, you can load 40 sheets.
*8
*9
*10
When loading copy paper, make sure that the stack height does not exceed the limit
mark. The maximum number of sheets you can load at a time depends on the paper
thickness and condition.
If you wish to copy onto thick (105g/m2, 28 lb or heavier) paper, select Thick Paper
mode. ⇒ "Special Paper Indication" in the System Settings manual
Paper size up to 600mm(23.6") is available when an optional HDD is installed.
*11
*12
Important
❒ If you use damp or curled paper, staples may become jammed or a misfeed
may occur.
Note
❒ When loading copy paper in the paper tray 1-4 and the large capacity tray
(LCT), place the copy side of the paper face up.
❒ When loading copy paper in the bypass tray, place the copy side of the paper
face down.
❒ When you use the bypass tray, it is recommended to set the copy paper direc-
tion to L.
❒ Postcards and envelopes should be fed from the paper tray 2 or the bypass tray.
❒ Some kinds of envelopes might cause misfeeds and wrinkles. In this case, push
down the green lever of the fusing unit.⇒ p.65 “When copying onto envelopes”
❒ Envelopes with large flaps should be fed from the paper tray 2 or a misfeed
might occur. See the illustration below.
2
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Copy Paper
❒ If you load paper of the same size in the same direction in two or more trays,
the machine automatically shifts to the other tray when the first tray in use
runs out of paper. This function is called Auto Tray Switching. (However, if
the Paper Type of one tray is recycled or special paper, the settings of the oth-
er trays must be the same for Auto Tray Switching.) It saves interrupting a
copy run to replenish paper when making a large number of copies. ⇒ p.41
“Selecting Copy Paper”, ⇒ p.184 “Auto Tray Switching”
1
❒ The paper types you can select in System Settings are only general classifica-
tions. The copy quality for every kind of paper in a classification is not guar-
anteed. See ⇒ p.26 “Non-recommended Paper” for more information.
Direction-fixed paper or 2-sided paper
Direction-fixed (top to bottom) or 2-sided paper (e.g., letterhead paper, punched
paper, or copied paper) might not be printed correctly depending on how the
originals and paper are placed. Set "Letterhead setting" in system settings, and
then place the original and paper as shown below. ⇒ “Letterhead Setting” on
p.204 “Input/Output”
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
Non-recommended Paper
R CAUTION:
• Do not use aluminum foil, carbon paper, or similar conductive paper to avoid
1
a fire or equipment failure.
Important
❒ Do not use any of the following kinds of paper or a fault might occur.
• Thermal fax paper
• Art paper
• Aluminum foil
• Carbon paper
• Conductive paper
• OHP transparencies for color copying
• Paper with perforated lines
• Hemmed paper
❒ Do not copy on the side of paper that has been already copied on or a fault
might occur.
Note
❒ Do not use the following kinds of paper or a misfeed might occur.
• Bent, folded, or creased paper
• Torn paper
• Slippery paper
• Perforated paper
• Rough paper
• Thin paper that has low stiffness
• Paper with a lot of paper dust on its surface
❒ If you make a copy on rough grain paper, the copy image might be blurred.
❒
Do not use paper that has been already copied or printed on or a fault might occur.
Paper Storage
Note
❒ When storing paper, the following precautions should always be followed:
• Do not store paper where it will be exposed to direct sunlight.
• Avoid storing paper in humid areas (humidity: 70% or less).
• Store on a flat surface.
❒ Under high temperature and high humidity conditions or low temperature
and low humidity conditions, store paper in a vinyl bag.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Toner
Toner
Handling Toner
1
Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an
open flame. Dispose of used toner containers in accordance with local regulations for plastics.
Our products are engineered to meet high standards of quality and functionality, and we rec-
ommend that you only use the expendable supplies available at an authorized dealer.
Important
❒ If you use toner other than the recommended type, a fault might occur.
Reference
If you want to add toner. ⇒ p.162 “D Adding Toner”
Toner Storage
When storing toner, the following precautions should always be followed:
• Store toner containers in a cool, dry place free from direct sunlight.
• Store on a flat surface.
Used Toner
Note
❒ Toner cannot be re-used.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics
1
28
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Copying
Basic Procedure
A Make sure that the machine is in F Enter the number of copies re-
Copy mode.
quired with the number keys.
If the machine is not in Copy
mode, press the {Copy} key.
Note
B When the machine is set for user
codes, enter a user code (up to 8
digits) with the number keys, and
then press the {#} key.
❒ The maximum copy quantity
can be set between 1 and 99 (de-
fault: 99).
❒ To change the number entered,
press the {Clear/Stop} key and
enter the new number.
The machine is ready to copy.
Reference
⇒ p.71 “Other Functions”
G Press the {Start} key.
C Make sure that there are no previ-
The machine starts copying.
ous settings remaining.
Note
Note
❒ When you place originals on the
❒ To clear settings, press the
exposure glass, press the {#
}
{Clear Modes} key.
key after all originals are
scanned.
D Place your originals.
❒ Copies are delivered face down.
Reference
⇒ p.31 “Placing Originals”
❒ To stop the machine during a
multi-copy run, press the
{Clear/Stop} key.
❒ To return the machine to the in-
itial condition after copying,
press the {Clear Modes} key.
E Set your desired settings.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
• When operations have been
suspended during printing
-System Reset
• When the handset is in use
The machine returns to its initial con-
dition automatically when your job is
finished, after a certain period of
time. This function is called "System
Reset".
• When the On-hook dialing func-
tion is in use
• When a recipient is being regis-
tered in the address list or
group dial list
2
Note
• When the Data In indicator is on
❒ You can change the System Reset
time. ⇒ "System Reset Timer" in
the System Settings manual
or blinking
• When the sample print or confi-
dential print screen is displayed
-Auto Off
The machine turns itself off automat-
ically after your job is finished, after a
certain period of time. This function is
called "Auto Off".
Note
❒ You can change the Auto Off time.
⇒ "Auto Off Timer" in the System
Settings manual
❒ Auto Off time function will not op-
erate in the following cases:
• When a warning massage is dis-
played
• When the service call massage is
displayed
• When the paper is jammed
• When the cover is open
• When "Adding Toner" message
is displayed
• When the toner is being replen-
ished
• When the User Tools/Counter
screen is displayed
• When fixed warm-up is in
progress
• When the facsimile, printer or
other functions are operating
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
Placing Originals
Limitation
Placing Originals on the
❒ Place originals after correction flu-
id and ink have completely dried.
Not taking this precaution could
dirty the exposure glass with
marks that will be copied.
Exposure Glass
A Lift the exposure glass cover or
2
the document feeder.
Note
Important
❒ Some copy functions may produce
different results depending on the
direction of the originals. For de-
tails, see the explanation for each
function.
❒ Do not open the exposure glass
cover or the document feeder
forcefully. Otherwise, the cover
of the document feeder might
open or be damaged.
Note
❒ Be sure to open the exposure
glass cover or the document
feeder by more than 30°. Other-
wise, the size of the original
might not be detected correctly.
B Place the original face down on
the exposure glass. The original
should be aligned to the rear left
corner.
Reference
⇒ p.18 “Originals”
1: Reference mark
2: Scale
Note
❒ Start with the first page to be
copied.
C Lower the exposure glass cover or
document feeder.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Placing Originals in the
Document Feeder
Placing a Stack of Originals in
the Document Feeder
Note
A Place the aligned originals face
up into the document feeder.
❒ The last page should be on the bot-
tom.
2
❒ Do not stack originals beyond the
limit mark on the side fence of the
document feeder.
❒ The original might become dirty if
it is written with a pencil or a sim-
ilar tool.
❒ You cannot place a multi-page
original with pages of different siz-
es in the document feeder. If the
originals contains pages of differ-
ent width, use the SADF function
and place each page one at a time.
Alternatively, place pages one at a
time on the exposure glass.
1: Limit mark
2: Document guide
Note
❒ Straighten curls in the originals
before placing them in the doc-
ument feeder.
❒ A multi-page original with the
same width can be placed in the
document feeder using Mixed Size
mode function.
❒
To avoid a multi-sheet feed, shuf-
fle the originals before placing
them in the document feeder.
❒ Do not place any foreign objects on
the sensors or cover them with
your hands. This could cause the
size not to be detected properly.
1: Sensor
Reference
Regarding originals that the docu-
ment feeder can handle. ⇒ p.18
“Originals”
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
90° Turn
Original Orientation
When you want to copy A3K,
B4K or 11" × 17"K size originals,
place your original in the land-
scape orientation, and then press
You can set the original orientation in
the following ways.
This function is useful for copying
torn originals or large originals.
the
key. The machine rotates
the original image, and you can
make copies as you wish. This is
useful for copying large originals
with the Staple, Duplex, Combine
or Stamp functions.
2
❖
Standard Orientation
Select this function when the origi-
nal direction is the same as the
copy paper direction.
❖
90 Turn
°
Note
This function rotates the copy im-
age by 90°.
Use this function when you want
to copy onto A3, B4 or 11" × 17" pa-
per.
❒ It is recommended to use this
function together with the Auto
Paper Selector or the Preset Re-
duce/Enlarge function.
A Press the
key.
A Press the [Special Original] key.
C Press the [OK] key.
B Select the original orientation.
Standard Orientation
A Make sure that the
key is
selected.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
C Press the [OK] key.
Placing Special Originals
Use this function when you want to
use Batch mode, SADF mode, Mixed
Size mode, or when you select the
original orientation.
2
Batch mode
Up to 50 standard originals can be set
in the document feeder at a time.
D Place your originals, and then
press the {Start} key.
Important
E After all the previously placed
originals are fed, place the next
originals.
❒ When placing special originals
such as translucent paper, place
them one by one.
Note
❒ The [Batch] key can be changed to
the [SADF] key. ⇒ p.204 “Switch to
Batch (SADF)”
A Press the [Special Original] key.
1: Limit mark
2: Document guide
Note
❒ When the Sort, Combine or Du-
plex function has been set, press
the {#} key after all originals are
scanned.
B Press the [Batch] key.
F Press the {Start} key.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
D When the machine instructs you
to place another original, place
the next page.
SADF mode
In SADF mode, even when an origi-
nal is placed page by page in the doc-
ument feeder (ADF), each page is
automatically fed when placed.
The second and subsequent pages
will be fed automatically without
pressing the{Start} key.
Note
2
❒ To use the SADF function, you
should make a setting in "User
Tools (Copy/Document Server
Features)", so that [SADF] will be
displayed when you press [Special
Original]. ⇒ p.204 “Switch to Batch
(SADF)”
A Press the [Special Original] key.
Note
❒ You can adjust the time the ma-
chine waits before being ready
for the next original. ⇒ p.204
“SADF Auto Reset”
Mixed Size mode
When you place different size origi-
nals which have the same width in
the document feeder at the same time,
the machine automatically checks the
size of the originals and makes cop-
ies.
B Press the [SADF] key.
Limitation
❒ When placing originals of different
sizes in the document feeder and
making copies without using the
Mixed Size mode, parts of the orig-
inal image might not be copied or
paper might become jammed.
C Place one page of an original, and
then press the {Start} key.
❒ The weight range for originals
placed with this function is 52 –
81g/m2, 14 – 20 lb.
The Auto Feed indicator is shown
on the display.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ The sizes of the originals that can
be placed together with this func-
tion are as follows:
E Adjust the guide to the widest
original size.
F Place the aligned originals face
Metric A3L • A4K, A4L • A5K
version
up into the document feeder.
Inch
11" × 17"L • 81/2" × 11"K,
G Press the {Start} key.
version 81/2" × 14"L • 81/2" × 11"K,
81/2" × 11"L • 51/2" × 81/2K,
2
81/2" × 14"L • 51/2" × 81/2"K
Placing Custom Size Originals
❒ Copying speed and scanning speed
When placing custom size originals in
the document feeder, specify the size
of the originals.
will be reduced.
A Press the [Special Original] key.
B Press the [Mixed size] key.
C Press the [OK] key.
Limitation
❒ Paper that has a vertical length of
128-297mm (5" – 11") and a horizon-
tal length of 128-1,260mm (5" – 49")
can be placed with this function.
Note
❒ Make sure the original is placed
correctly so that it is fed straight.
❒ When placing paper 433mm or larg-
er in the document feeder (ADF),
there are cases when the paper will
be jammed, creased, or not fed.
A Press the [Special Original] key.
D Align the rear and left edges of
the originals as shown in the il-
lustration.
B Press the [Custm Size Origi.] key.
A4
A3
1
2
CP19AE
1: Place in into the document feeder.
2: Vertical size
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
C Enter the horizontal size of the
original with the Number keys,
and then press the [#] key.
2
Note
❒ If you make a mistake, press the
[
Clear] or {Clear/Stop} key, and
then enter the value again.
D Enter the vertical size of the origi-
nal with the Number keys, and
then press the [#] key.
E Press the [OK] key.
F Place your originals, and then
press the {Start} key.
Note
❒ If you make a mistake, press the
[
Clear] or {Clear/Stop} key, and
then enter the value again.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Basic Functions
The following basic functions are ex-
plained in this section.
Note
❒ You can select the functions to be
activated when System Reset is
turned on, when Energy Saver is
turned off, or after the machine is
turned on.
❖
Adjusting Copy Image Density
Auto and Manual Image Density
2
❖
Selecting Original Type Setting
Text, Text·Photo, Photo, Pale, and
Generation Copy
❒ You can change the default set-
tings for basic functions.
❖
❖
Selecting Copy Paper
Auto Paper Select and Manual Pa-
per Select
Reference
⇒ "Settings You Can Change with
the User Tools" in System Settings
manual
Auto Reduce/Enlarge
The machine can choose an appro-
priate reproduction ratio based on
the paper and original sizes you se-
lect.
Adjusting Copy Image Density
You can adjust the copy image densi-
ty to match your originals.
❖
❖
Sort
There are three types of adjustment
available:
Copies can be assembled as sets in
sequential order.
❖
Auto Image Density
The machine automatically adjusts
the image density.
Rotate Sort
Every other copy set is rotated by
90° KLand delivered to the copy
tray.
❖
Manual Image Density
If you require darker or lighter
copies, adjust the image density
yourself.
❖
❖
Stack (The optional Bridge unit and an
optional finisher are required for this
function)
Copies can be assembled with each
page placed.
❖
Combined Auto and Manual Image
Density
Use when copying originals with a
dirty background (such as news-
papers). You can adjust the fore-
ground density while leaving the
background unchanged.
Staple (The optional Bridge unit and
an optional finisher are required for
this function)
Each copy set can be stapled to-
gether.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Functions
Auto Image Density
Combined Auto and Manual Image
Density
A Make sure that the [Auto Image Den-
sity] key is selected.
A Make sure that the [Auto Image Den-
sity] key is selected.
Note
❒ If the [Auto Image Density] key is
not selected, press the [Auto Im-
age Density] key.
2
B Press the [Lighter] or [Darker] key to
adjust the density.
Note
❒ If the [Auto Image Density] key is
not selected, press the [Auto Im-
age Density] key.
❒ If you do not wish to set any
other functions, press the
{Start} key to start copying.
Note
Manual Image Density
❒ If you do not wish to set any
other functions, press the
{Start} key to start copying.
A Press the [Auto Image Density] key
to cancel it.
B Press the [Lighter] or [Darker] key to
adjust the image density.
Note
❒ If you do not wish to set any
other functions, press the
{Start} key to start copying.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
A Press the appropriate key to select
Selecting Original Type Setting
the original type.
Select one of the following types to
match your originals:
❖
Text
Select this mode when your origi-
nals contain only text (no pictures).
2
❖
Text/Photo
Select Text·Photo when your origi-
nals contain photographs or pic-
tures with text.
Note
❒ If "Hide" has been selected in
"Original Type Display" of the
User Tools, press the [Original
Type] key to select the original
❖
❖
Photo
Delicate tones of photographs and
pictures can be reproduced with
this mode.
type, and then press the [OK
]
key. ⇒ "Original Type Display"
Pale
on p.184 “General Features 1/4”
Select this mode for originals that
have lighter lines written in pencil,
or for faint copied slips. The faint
lines will be clearly copied.
❖
Generation Copy
If your originals are copies (gener-
ation copies), the copy image can
be reproduced sharply and clearly.
❒ If you do not wish to set any
other functions, press the
{Start} key to start copying.
Note
❒ You can hide all the original type
keys on the initial display. ⇒ p.185
“Original Type Display”
❒ You can adjust the quality level for
each original type. ⇒ p.185 “Copy
Quality”
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Functions
Selecting Copy Paper
There are two ways to select copy paper:
❖
Auto Paper Select
The machine selects a suitable size of copy paper automatically based on the
original size and the reproduction ratio. ⇒ p.43 “Rotated copy”
2
❖
Manual Paper Select
Choose the tray containing the paper you wish to copy onto: a paper tray, by-
pass tray or large capacity tray (LCT).
Reference
⇒ p.61 “Copying from the Bypass Tray”
Limitation
❒ Only the paper trays set to "No Display" or "Recycled Paper" in "Paper Type",
and also set to "Yes" in "Apply Auto Paper Select", can be selected in Auto Pa-
per Select mode. ⇒ "Paper Size Setting" in the System Settings manual
❒ If you set all the paper trays other than "No Display" or "Recycled Paper", you
cannot use Auto Paper Select.
Note
❒ See the following table for copy paper sizes and directions that can be used
with Auto Paper Select (when copying at a ratio of 100%).
❖
Metric version
Where Original Is Placed
Paper Size and Direction
Exposure glass
A3L, B4L, A4KL, B5KL, A5L, 81/2" ×
14"L, 81/2" × 13"L
Document feeder
A3L, B4L, A4KL, B5KL, A5KL, 81/2"
× 13"L
❖
Inch version
Where Original Is Placed
Paper Size and Direction
Exposure glass
11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL,
10" × 14"L, 8" × 10"L
Document feeder
11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL,
10" × 14"L, 51/2" × 81/2"L
❒ For some originals, the original size might not be detected correctly. ⇒ p.20
“Sizes difficult to detect”
❒ When you load special paper, such as recycled paper, in a paper tray, you can
have the paper type shown on the display. ⇒ "Special Paper Indication" in the
System Settings manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Auto Paper Select
A Make sure that the [Auto Paper Select] key is selected.
If the [Auto Paper Select] key is not selected, press the [Auto Paper Select] key.
2
Note
❒ If you do not wish to set any other functions, press the {Start} key to start
copying.
❒ Trays with a key mark will not be automatically selected. ⇒ "Paper Size
Setting" in the System Settings manual
Manual Paper Select
A Select the paper tray, bypass tray or large capacity tray (LCT).
Note
❒ If you do not wish to set any other functions, press the {Start} key to start
copying.
❒ If "Hide" has been selected in "Paper Display" of the User Tools, press the
[
Auto Paper Select] key. ⇒ p.184 “Paper Display”
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Functions
-Rotated copy
If the direction in which your original is placed (L or K) is different from that
of the paper you are copying onto, this function rotates the original image by 90°
and fits it on the copy paper. This function works when Auto Paper Select or
Auto Reduce/Enlarge is selected. ⇒ "Auto Paper Select" on p.41 “Selecting
Copy Paper” and ⇒ p.44 “Auto Reduce/Enlarge”
2
Original
Paper Orien- Copy Orien-
Orientation tation
tation
R
GCROTA0E
Limitation
❒ The default setting for "Auto Tray Switching" is "With image rotation ". You
cannot use the Rotated Copy function if this setting is changed to "Without
image rotation" or "Off". ⇒ p.184 “Auto Tray Switching”
❒ You cannot use the Rotated Copy function when enlarging onto B4 or A3 size
paper. In this case, place your original in the L direction.
Original Size and Direction
Copy Paper Size and Direc-
tion
You cannot
rotate:
A4,
B5, or
A5
When enlarg- B4, A3
ing to →
K
R
GCROTA1E
GCROTA2E
However,you A4,
can use: B5, or
When enlarg- B4, A3
ing to →
A5
R
R
L
GCROTA3E
GCROTA4E
❒ You cannot use the Rotated Copy function when "Left 2" or "Top 2" is selected
for stapling when using the 1000-sheet finisher. ⇒ p.51 “Staple”
❒ You cannot use the Rotate Copy function if the Staple function is selected
when using the 500-sheet finisher.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ The reproduction ratios the ma-
chine will select are 25 – 400% (25-
200% when setting originals in the
document feeder).
Auto Reduce/Enlarge
The machine can choose an appropri-
ate reproduction ratio based on the
paper and original sizes you select.
❒ For some originals, the original
size might not be detected correct-
ly. ⇒ p.20 “Sizes difficult to de-
tect”
2
❒ You can place originals of different
sizes in the document feeder at the
same time. ⇒ p.35 “Mixed Size
mode”
❒ You cannot use the Rotated Copy
function when enlarging to B4 or
A3. When enlarging to B4 or A3
size copy paper, place the original
in the L direction.
Limitation
❒ You cannot use the bypass tray
with this function.
A Press the [Auto Reduce/Enlarge] key.
Note
❒ When using Auto Reduce/En-
large, see the following table for
the original sizes and directions
you can use.
❖
Metric version
Where Original Is Original Size and
Placed
Direction
A3 , B4
A4KL, B5KL
A5L, 81/2"
14"
81/2"
13"
A3 ,B4
B5KL, A5KL
B Select the paper tray.
Exposure glass
L
L,
,
Note
×
L
L,
❒ If you do not wish to set any
other functions, press the
{Start} key to start copying.
×
Document feeder
L
L,A4KL
,
,
81/2"
13"L
×
❖
Inch version
Where Original Is Original Size and
Placed
Direction
11"
17"L, 81/2"
Exposure glass
×
×
14"L, 81/2"
11"KL, 10"
8" 10"
×
×
14"
L,
×
L
Document feeder
11"
×
17"L, 81/2"
×
14"L, 81/2"
11"KL,10"
51/2" 81/2"L
×
×
14"L,
×
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Sort/Stack/Staple
Sort/Stack/Staple
The machine can scan your originals into memory and automatically sort the
copies.
❖
Sort
• Sort
2
• Rotate Sort
• Shift sort (an optional finisher and the optional Bridge unit are required)
❖
❖
Stack
• Stack
(an optional finisher and the optional Bridge unit are required)
Staple (an optional finisher and the optional Bridge unit are required)
With 1000-Sheet Finisher
• Top
• Left 2
• Bottom
• Top 2
With 500-Sheet finisher
• Top
Limitation
❒ You cannot use the bypass tray with this function.
❒ The maximum capacity for Sort and Stack with paper smaller than B5 L is
100 sheets.
Note
❒ When the number of copies exceeds the tray capacity, remove copies from the
tray.
❒ The maximum tray capacity is as follows.
Paper Size and Direction
Paper Capacity
and Weight
A4KL, B5KL, A5KL, B6L, A6L, PostcardL, 81/2"
×
500 sheets *1
(80g/m2) (20 lb.)
Internal
tray
11"KL, 71/4"
×
101/2"KL, 51/2"
×
81/2"KL, 8" 101/2"KL
× ,
8" 10"KL, 16KKL
×
A3 , B4 , 11"
17"L, 81/2"
81/4" 14"L, 81/4"
13" , 11"
L
L
×
×
×
14"
15"
L
, 8"
, 11"
×
13"L, 81/2"
14" , 10"
×
×
13"
L
,
250 sheets *2
(80g/m2) (20 lb.)
×
×
L
L
×
L
14"L,
10" 15" , 8KL
×
L
37/8" 71/2"L, 41/8" 91/2"L, C5 EnvL, C6 EnvL, DL EnvL
×
×
–
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Paper Size and Direction
Paper Capacity
and Weight
A3L, B4L, A4KL, B5KL, A5L, 11" × 17"L, 81/2" × 14"L,
11" × 15L *3 , 11" × 14"L, 10" × 14"L *3 , 10" × 15"L *3 , 81/2" ×
11"KL, 71/4" × 101/2"KL *3 , 51/2" × 81/2"L, 8" × 13"L, 81/2"
Internal
tray 2
(1 bin tray)
125 sheets
(80g/m2) (20 lb.)
× 13"L, 81/4" × 13"L, 8" × 101/2"KL, 8" × 10"KL *3 , 81/4" ×
14L
A4KL, B5KL, A5KL, B6L, A6L, 81/2" × 11"KL, 71/4"
Shift sort
tray
250 sheets
(80g/m2) (20 lb.)
2
× 101/2"KL, 51/2" × 81/2"L, 8" × 10"KL
A3L, B4L, 11" × 17"L, 81/2" × 14"L, 8" × 13"L, 81/2" ×
125 sheets
(80g/m2) (20 lb.)
13"L, 81/4" × 13"L
A4KL, B5K, 81/2" × 11"KL, 8" × 101/2"K
500-Sheet
Finisher
500 sheets
(80g/m2) (20 lb.)
A3L, B4L, 11" × 17"L, 11" × 14"L, 81/2" × 14"L, 81/2" ×
13"L
250 sheets
(80g/m2) (20 lb.)
1000-Sheet Finisher proof tray
Finisher
250 sheets
(80g/m2) (20 lb.)
A4KL, B5KL, A5KL, B6L, A6L, PostcardL, 81/2" ×
11"KL, 71/4" ×101/2"KL *4 , 51/2" × 81/2"L, 8" × 101/2"KL,
8" × 10"L *4
*4 , 11"
13"L, 81/2"
×
14"
L
, 10"
×
14"L
50 sheets
(80g/m2) (20 lb.)
A3
*4 , 10"
13"L, 81/4"
L
, B4
L
, 11"
*4 , 81/2"
14"
×
17"
L
, 11"
×
15"
, 8"
L
×
15"
L
×
14"L
×
×
13"L, 81/4"
×
×
L
Finisher shift tray
1000 sheets
(80g/m2) (20 lb.)
A4KL, B5KL *5 , 81/2" × 11"KL, 71/4" × 101/2"L,
8" × 101/2"KL
A3L, B4L, 11" × 17"L, 11" × 14"L, 81/2" × 14"L, 8" × 13"L,
500 sheets
(80g/m2) (20 lb.)
81/2" × 13"L, 81/4" × 13"L, 81/4" × 14"L
*1
*2
*3
250 sheets when the optional bridge unit is installed.
125 sheets when the optional bridge unit is installed.
1
To place paper of sizes 10 /2" × 7 1/4"K, 8" × 10"KL, 11" × 15"L, 10" × 14"L,
and 10" × 15"L, use the paper tray 2.
*4
*5
1
To place paper of sizes 10 /2" × 7 1/4"K, 8" × 10"KL, 11" × 15"L, 10" × 14"L,
and 10" × 15"L, use the paper tray 2 or the optional bypass tray.
B5L cannot be shifted.
Note
❒ When selecting Sort, Stack or Staple functions, copies of some sizes can be
made, by feeding the paper from tray 2 or the optional bypass tray. Refer to
each section. ⇒ p.47 “Sort”, p.49 “Stack”, p.51 “Staple”
❒ When using the Rotate Sort or Staple functions, the capacity may be reduced.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Sort/Stack/Staple
❒ The paper sizes that can be used
in the Rotate Sort function are as
follows.
Sort
Copies can be assembled as sets in se-
quential order.
Metric version
Inch version
A4KL, B5KL
81/2" × 11"K
❖
Sort
❒ To use the Rotate Sort function,
two paper trays with paper
identical in size and different in
direction (KL) are required.
Copies are assembled as sets in se-
quential order.
2
Reference
3
3
3
3
For the paper capacity of the op-
tional finishers ⇒ p.223 “500-
Sheet Finisher (Option)”, ⇒
p.224 “1000-Sheet Finisher (Op-
tion)”.
2
2
2
2
1
1
1
1
Note
❒ The paper sizes that can be used
in the Sort function are as fol-
lows.
❖
Shift Sort
• 500-Sheet Finisher/1000-Sheet
Finisher/Shift Sort Tray
Metric version
A3L, B4L,
A4KL, B5KL,
A5L
Each time the copies of one set
or those of each job are deliv-
ered, the next copy is shifted
when delivered so that you can
differentiate each set or job. If
the shift sort tray is installed, it
provides this function by slid-
ing from side to side.
Inch version
11" × 17"L,
81/2" × 14"L,
81/2" × 11"KL,
51/2" × 81/2"L
❖
Rotate Sort
Every other copy set is rotated by
90°KL and delivered to the copy
tray.
3
2
1
3
3
3
2
2
2
1
1
1
Note
❒ When an optional finisher is in-
stalled, you can switch to or
from the Rotate Sort function
with the User Tools. ⇒ "Select
Stack Function" on p.204 “In-
put/Output”
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❖
When the 500-Sheet Finisher is
installed
Note
❒ The paper sizes that can be used
in the Sort function are as fol-
lows.
500-Sheet
Finisher
1000-Sheet Fin-
isher
A3
A4KL,B5
11"
L
, B4
L
K
,
A3L, B4L,
A4KL, B5K,
11" × 17"L,
2
,
×
×
×
×
×
17"
L,
11"
11"
10"
10"
81/2"
81/2"
81/2"
15"L *1
,
11" × 15"L *1
,
14"
L
,
11" × 14"L,
14"L *1
,
,
10" × 14"L *1
10" × 15"L *1
81/2" × 14"L,
81/2" × 13"L,
81/4" × 14"L,
,
,
❖
When the 1000-Sheet Finisher is
installed
15"L *1
×
×
×
14"
13"
L,
L
,
81/4" × 13"L,
11"KL
,
8"
8"
×
×
101/2"K
10"K *1
×
,
,
8" × 13"L,
81/2" × 11"KL,
71/4"
8" ×101/2"KL,
101/2"K *1
8" × 10"KL *1
71/4" ×
,
101/2"KL *1
Note
*1
1
To place paper of sizes 7 /4" ×
❒ When the optional finisher is in-
stalled, use the User Tools to
display [Rotate Sort]. ⇒ "Select
Stack Function" on p.204 “In-
put/Output”
1
10 /2"K, 8" × 10"KL, 11" ×
15"L, 10" × 14"L, and 10" ×
15"L, use the paper tray 2 or
the optional bypass tray.
A Press the [Sort] or [Rotate Sort] key.
When a finisher is not installed
B Enter the number of copy sets
❖
with the number keys.
Limitation
❒ The maximum number of sets is
99.
Note
❒ To change the entered number,
press the {Clear/Stop} key.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Sort/Stack/Staple
C Place your originals, and then
Stack
press the {Start} key.
Copies can be assembled with each page
placed.
When placing a stack of originals
in the document feeder
❖
Shift Stack
A Place a stack of originals in the
document feeder, and then
press the {Start} key.
• 500-Sheet/1000-Sheet Finish-
er/Shift Sort Tray
2
This function groups copies of
each page in a multi-page origi-
nal together. Every other page
stack is shifted for ease of sepa-
ration. If shift sort tray is in-
stalled, it provides this function
by sliding from side to side.
Note
❒ The last page should be on
the bottom.
❒ If an original is misfed dur-
ing sorted copying, reset
your originals in the docu-
ment feeder according to the
instructions on the display,
and try again.
3
2
1
When setting an original on the
exposure glass or in the document
feeder using Batch mode
Note
❒ The paper sizes that can be used
with the Stack function are as fol-
lows.
Reference
⇒ p.34 “Batch mode”
A Place the original, and then
500-Sheet Fin- 1000-Sheet Fin-
isher
isher
press the {Start} key.
A3L, B4L,
A3L, B4L,
Note
A4KL, B5K, A4KL, B5K,
11" × 17"L,
11" × 15"L *1
11" × 14"L,
10" × 14"L *1
10" × 15"L *1
11" × 17"L,
❒ Start with the first page to be
,
11" × 15"L *1
,
copied.
11" × 14"L, 10" ×
B Place the next original. When it
is placed on the exposure glass,
press the {Start} key.
,
,
14"L *1 , 10" ×
15"L *1 , 81/2" ×
81/2" × 14"L, 14"L, 81/2" ×
81/2" × 13"L, 13"L, 81/4" ×
81/2" ×
14"L, 81/4" ×
13"L, 8" × 13"L,
Note
11"KL, 8" ×
❒ When using the SADF func-
tion, each page of the original
will automatically be fed
when placed, without press-
ing the {Start} key. ⇒ p.35
“SADF mode”
101/2"K, 8" × 81/2" × 11"KL,
10"K *1 , 71/4" 8" × 101/2"KL,
× 101/2"K *1
8" × 10"KL *1
71/4" ×
,
101/2"KL *1
*1
1
To place paper of sizes 7 /4" × 10
1/2"K, 8" × 10"KL, 11" × 15"L,
10" × 14"L, and 10" × 15"L, use the
paper tray 2 or the optional bypass
tray.
❒ Set the original in the same
direction as the first one.
C After all originals are scanned,
press the {#} key.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
A Place the original, and then
Reference
press the {Start} key.
For the maximum tray capacity of
the optional finishers ⇒ p.223
“500-Sheet Finisher (Option)”, ⇒
p.224 “1000-Sheet Finisher (Op-
tion)”.
Note
❒ Start with the first page to be
copied.
B Place the next original. When it
is placed on the exposure glass,
press the {Start} key.
A Press the [Stack] key.
2
Note
❒ When using the SADF func-
tion, each page of the original
will automatically be fed
when placed, without press-
ing the {Start} key. ⇒ p.35
“SADF mode”
❒ Place the original in the same
B Enter the number of copies with
direction as the first one.
the number keys.
Note
❒ To change the entered number,
press the {Clear/Stop} key.
C Place your originals, then press
the {Start} key.
When placing a stack of originals
in the document feeder
A Place a stack of originals in the
document feeder, and then
press the {Start} key.
Note
❒ The last page should be on
the bottom.
When placing an original on the
exposure glass or in the document
feeder using Batch mode
Reference
⇒ p.34 “Batch mode”
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Sort/Stack/Staple
Staple
An optional finisher and the bridge unit are required to use this function.
Each copy set can be stapled together.
2
Limitation
❒ You cannot use the following paper in this function:
• Postcards
• Translucent paper
• OHP transparencies
• Label paper (adhesive labels)
• Thick paper
• Thin paper
• Curled paper
• Paper of low stiffness
• Paper of different vertical sizes
Note
❒ For this mode, the following limitation applies. When the number of copies
exceeds the tray capacity, copying stops. In this case, remove the copies from
the shift tray, and then resume copying.
Paper size
Stapler capacity
20 sheets (80g/m2)
500-Sheet Finisher
A3 , B4
L
L
, A4KL
,
A3L, B4L, 11" ×
B5 , 11"
15"
, 10"
15"
K
×
17"
*1 , 11"
L
,
17"L, 11" ×15"L, 11"
× 14"L, 10" × 14"L,
11"
14"
10"
×
L
L
×
10" × 15"L, 81/2" ×
×
14"L *1
,
14"L, 81/2" × 13"L
×
L
*1 , 81/2"
×
14"L, 81/2"
81/2"
101/2"K, 8"
71/4"
×
13"L,
A4KL, B5K, 81/2"
11"KL, 8"
101/2"K
10"K, 71/4"
101/2"K
×
,
30 sheets (80g/m2)
×
11"KL, 8"
×
×
×
10"K *1
,
8"
×
×
×
101/2"K *1
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
30 sheets (80g/m2)
1000-Sheet Finisher
A3L, B4L, A4KL, A3L, B4L, 11" ×
B5KL, 11" × 17"L, 17"L, 11" ×15"L, 11"
11" × 15"L *1 , 11" ×
× 14"L, 10" × 14"L,
10" × 15"L, 81/2" ×
14"L, 81/2" × 13"L,
14"L, 10" × 14"L *1
,
10" × 15"L*1 , 81/2" ×
81/4" × 14"L, 81/4" ×
14"L, 81/2" × 13"L,
81/4" × 14"L, 81/4" ×
13"L, 8" × 13"L,
13"L, 8" × 13"L
50 sheets (80g/m2)
A4KL, B5KL,
81/2" × 11"KL,
8" × 101/2"KL,
8" × 10"KL, 71/4" ×
101/2"KL
81/2" × 11"KL, 8" ×
2
101/2"KL, 8" ×
10"KL *1 , 71/4" ×
101/2"KL *1
*1
To load paper of sizes 7 1/4" × 10 1/2"L, 8" × 10"KL, 11" × 15"L, 10" × 14"L, and
10" × 15"L, use the paper tray 2.
❒ In the following cases, the copies will be delivered to the shift tray without
stapling.
• When the number of sheets for one set is over the stapler capacity.
• When memory reaches 0% during copying.
❒ When you select Staple, Sort mode is automatically selected.
❒ Staple function is not available for mixed size originals. When using Mixed
Size mode in staple function, select Auto Reduce/Enlarge. ⇒ p.44 “Auto Re-
duce/Enlarge”
Reference
If you want to add staples, ⇒ p.172 “d Adding Staples”.
When staples are jammed, ⇒ p.175 “e Removing Jammed Staples”.
When using Double copies, or "1 Sided → 1 Sided", "1 Sided → 2 Sided", "2
Sided → 1 Sided", and "2 Sided → 2 Sided" in Combine mode, select K orig-
inal for L copy and L original for K copy.
Stapling position and original setting
Place all the originals in a direction in which they can be read. They will auto-
matically be rotate copied. When there is copy paper that is identical in size and
direction to your original, the staple positions are as follows:
When using Double copies, or "1 Sided 2 Pages→ Combine 1 Side" and "1 Sided
4 Pages→ Combine 2 Sided" in Combine mode, select Koriginal for Lcopy and
L original for K copy.
When using "Left 2" or "Top 2" with Double copies, or "1 Sided → 1 Sided", "1
Sided → 2 Sided", "2 Sided → 1 Sided", or "2 Sided → 2 Sided" in Combine mode,
select K original for L copy and L originals for K copy.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Sort/Stack/Staple
❖
500-sheet Finisher
When your machine is equipped with the 500-sheet finisher, the stapling po-
sition will be fixed to "Top".
Original location
Stapling
position
Exposure
glass
Document
Feeder
K
L
2
Note
❒ Original images are not rotated.
❖
1000-Sheet Finisher
Original location
Stapling
position
Exposure
glass
Document
Feeder
K
L
K
L
K
*1
L
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Original location
Stapling
position
Exposure
glass
Document
Feeder
*1
K
L
2
*1
Not available for paper size larger than A4.
Note
❒ You cannot change stapling positions during copying.
❒ When the original image is rotated, the stapling direction turns by 90°.
❒ When using "Left 2" or "Top 2" with Combine mode, Double copies, or Auto
Reduce/Enlarge, "Blank part will appear. Check orientation." message may
be displayed. In this case, change the paper orientation.
❒ The maximum original image size that can be rotated is as follows.
Metric version
Inch version
A4
81/2" × 11"
❒ When "Left 2" or "Top 2" is selected, the following settings are useful to rotate
images appropriately:
• "Auto Reduce/Enlarge" or "Auto Paper Select"
• "With image rotation" in "Auto Tray Switching" of User Tools
A Select one of the stapling positions.
❖
500-Sheet Finisher
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Sort/Stack/Staple
❖
1000-Sheet Finisher
2
Note
❒ When you select the stapling position, Sort mode is automatically selected.
Reference
⇒ p.52 “Stapling position and original setting”
B Enter the number of copy sets with the number keys.
Note
❒ To change the entered number, press the {Clear/Stop} key.
C Place your originals, then press the {Start} key.
When placing a stack of originals in the document feeder
A Place a stack of originals in the document feeder, and then press the
{Start} key.
Note
❒ The last page should be on the bottom.
When placing an original on the exposure glass or in the document feeder
using Batch mode
Reference
⇒ p.34 “Batch mode”
A Place the original, and then press the {Start} key.
Note
❒ Start with the first page to be copied.
B Place the next original. When it is placed on the exposure glass, press the
{Start} key.
Note
❒
When using the SADF function, each page of the original will automatically
p.35 “SADF mode”
be fed when placed, without pressing the {Start} key.
⇒
❒ Place the original in the same direction as the first one.
C After all originals are scanned, press the {#} key.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Reference
To Stop Scanning Temporarily
Scanning will stop when memory
reaches 0% during sorted copying.
However, you can change this set-
ting so that all the scanned pages
are copied and delivered to the
tray. After which, the machine au-
tomatically continues scanning the
remaining originals. ⇒ "Memory
Full Auto Scan Restart" on p.204
“Input/Output”
When you are using the Sort, Stack, or
Staple function, the originals are
scanned into memory.
A Press the {Clear/Stop} key to stop
originals from being scanned into
memory.
2
To resume scanning
A Press the {Start} key.
A Press the [No] key to resume
The scanned pages are delivered to
the tray. Then, the image data in
memory is cleared.
scanning.
Note
❒ Scanned images in memory
are not cleared.
B Remove the copies and continue
copying by following the instruc-
tions on the display.
To clear scanned images of the
originals
To Remove Paper from the
Staple Unit
A Press the [Yes] key.
Scanning is stopped with the
images cleared.
If you cancel a stapling copy job in the
middle of the job, paper might be left
in the staple unit. In this case, remove
the paper from the staple unit.
When Memory Reaches 0%
Scanning will be stopped if the size of
scanned image data exceeds memory
capacity.
A Press the {Clear Modes} key to can-
cel the copy settings.
B Place the next original, and then
Note
press the {Start} key.
❒ There is enough memory to store
approximate 1,000 originals of A4,
81/2" × 11" size. The number of
originals that can be stored in
memory varies depending on the
memory setting and original type.
In addition, the number of origi-
nals that can be stored in memory
will be reduced when you use oth-
er functions.
The paper left in the staple unit is
automatically delivered, and then
the next job starts.
Note
❒ When paper is not delivered
and a message is displayed, fol-
low the instructions on the dis-
play to remove the paper.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying from the Paper Tray 2
Copying from the Paper Tray 2
Use the paper tray 2 for copying onto
special paper (OHP transparencies,
label paper (adhesive labels), thick
paper (for example postcards and en-
velopes), thin paper) as well as plain
paper.
Using Tray 2 as Bypass Tray
A {Select tray 2, and then press the
#} key.
2
You can also set special paper in the
System Settings. ⇒ "Paper Size Set-
ting" in the System Settings manual
Note
❒ If you do not use standard size
copy paper, you should input ver-
tical and horizontal dimensions.
The sizes that you can input are as
follows.
Important
❒ The paper size and type settings
programmed by pressing the
Metric
version
•
•
Vertical: 100 – 297mm
Horizontal: 148 – 432mm
{
#} key are cleared and reset au-
Inch
version
•
•
Vertical: 4.0" – 11.7"
tomatically when copying is
completed.
Horizontal: 5.9" – 17.0"
❒ If the paper size displayed on
the key for tray 2 is different
from the paper set in tray 2, pa-
per might be misfed. Make sure
to remove paper in the tray after
copying.
❒ For the paper size, type, and thick-
ness you can use, or the maximum
number of sheets you can load at a
time, refer to “Copy Paper” ⇒
p.22.
❒ To make copies onto special paper
(OHP transparencies, thick paper
(for example postcards and enve-
lopes), thin paper, label paper (ad-
hesive labels)), you need to specify
the paper type. ⇒ p.64 “When cop-
ying onto special paper”
When copying onto standard size
paper
This setting is necessary when
temporarily copying onto a paper
size which is not displayed on the
size key of tray 2.
❒ To load paper, refer to “Changing
the Paper Size in Tray 1-4/Paper
Tray Unit” ⇒ p.170.
Note
❒ This setting is not necessary if
the size of paper displayed on
the key for tray 2 and that of pa-
per set in tray 2 are the same.
❒ You can also specify the size of
paper directly with the paper
size selector for the paper tray 2.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ Some kinds of envelopes might
C Press [OK].
cause misfeeds and wrinkles. In
this case, push down the green
lever of the fusing unit. ⇒ p.65
“When copying onto enve-
lopes” Also, be sure to place the
front face of the envelope up-
wards.
Note
❒ The copy paper sizes that can
be selected are as follows:
• A3
B5KL, B6
card , 11
17L, 81/2
81/2 11KL, 51/2 81/2L
71/4 101/2KL, 8
13
81/2 13L, 81/4
13
11 14 , 11 15 , 10
10 14
15L, 81/4
101/2KL, 8
10KL
8KL, 16KKL, 37/8"
71/2"L, 41/8"
Env , C6 Env
L
, B4
L
L
×
, A4KL, A5
, A6 , Post-
14
L,
L
L
×
×
×
L,
,
2
×
A Press [Select Size].
×
L,
×
×
L,
×
×
L
×
L
×14L,
×
L
,
8
×
×
,
×
×
91/2"L, C5
L, DL EnvL
L
B Select the paper size.
When copying onto custom size
paper
Note
❒ If [2 Sided] is selected for copy-
ing in [Dup./Combine/Series] (for
example [1 Sided]→[2 Sided]), se-
lect [1 Sided] for copying (for ex-
ample [1 Sided]→[1 Sided]).
Important
❒ You should specify the size of
copy paper to avoid paper mis-
feeds.
Limitation
❒ Paper will be automatically de-
livered to the Internal tray.
A Press [Custom Size].
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying from the Paper Tray 2
B Press the [Vertical inch] key, en-
ter the vertical size of the paper
with the number keys, and
then press the {#} key.
D To register the custom size en-
tered, press the [Program] key
and then press the [Exit] key.
2
Note
Note
❒ If you do not register the cus-
❒ To change the number en-
tered, press the [Clear] or
{Clear/Stop} key and enter
the new number.
tom size, go to step B.
❒ Only one custom size can be
stored.
❒ To recall the custom size
C Enter the horizontal size of the
paper with the number keys,
and then press the {#} key.
stored, press the [Recall] key.
❒ If you do not register the cus-
tom size, the size you set is
deleted when modes are
cleared.
When copying onto special paper
To make copies onto special paper
(OHP transparencies, thick paper
(for example postcards and enve-
lopes), thin paper, label paper (ad-
hesive labels)), specify the paper
type in "Special paper".
Note
❒ If the [Horiz inch] key is not
highlighted, press the [Horiz
inch] key.
Note
❒ If [2 Sided] is selected for copy-
ing in [Dup./Combine/Series] (for
example [1 Sided]→[2 Sided]), se-
lect [1 Sided] for copying (for ex-
ample [1 Sided]→[1 Sided]).
❒ To change the number en-
tered, press the [Clear] or
{Clear/Stop} key and enter
the new number.
❒ Select [Thick Paper] if the paper
weight is 105g/m2 (28 lb.) or
more.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
A Select paper type in "Special
paper".
2
B Press the [OK] key.
C {Set your originals and press the
Start} key.
Important
❒ When you place an OHP trans-
parency, make sure that its front
and back faces are properly po-
sitioned. Place the front face up-
wards.
❒ To avoid paper misfeeds, fan
the paper before setting it in the
tray.
❒ When copying onto OHP trans-
parencies, remove copied sheets
one by one.
Note
❒ You can also set the size of pa-
per in tray 2 in System Settings.
⇒ "Paper Size Setting" in the
System Settings manual
❒ The maximum limit for stacking
special paper is different from
that of plain paper. ⇒ p.160 “B
Loading Paper”
❒ When setting OHP transparen-
cies, thin paper or label paper
(adhesive labels), Staple, Shift
or Sort function may not be
used.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying from the Bypass Tray
Copying from the Bypass Tray
The optional bypass tray is required to use this function.
Use the bypass tray to copy onto spe-
cial paper (OHP transparencies, label
paper (adhesive labels), thick paper
(for example postcards and enve-
lopes), thin paper) , and copy paper
that cannot be loaded in the paper
trays.
❒ When using paper larger than 433
mm in size, load it so that it is fed
straight into the machine.
2
❒ When paper larger than 433 mm in
size is used, the paper may become
wrinkled, may not be fed into the
machine, or may cause paper jams.
❒ The maximum number of sheets
you can load at the same time de-
pends on the paper type. For de-
tails about the paper capacity of
the bypass tray, ⇒ p.22 “Copy Pa-
per”.
Preparation
When copying from the bypass
tray, select [1 Sided] for copying in
[
[
Dup./Combine/Series](for example
1 Sided]→[1 Sided] or [2 Sided]→[
1
Sided]).
❒ Some kinds of envelopes might
cause misfeeds and wrinkles. In
this case, push down the green le-
ver of the fusing unit. ⇒ p.65
“When copying onto envelopes”
Also, be sure to place the front face
of the envelope downwards.
Note
❒ The machine can automatically de-
tect the following sizes as standard
size copy paper.
Metric A3L, A4L, A5L, 8" × 13"L
version
11" × 17"L, 81/2" × 14"L,
Inch
version
A Open the bypass tray.
81/2" × 11"L, 51/2" × 81/2"L
❒ If you do not use the standard size
copy paper or if you use special pa-
per, you should input vertical and
horizontal dimensions. ⇒ p.22
“Copy Paper”, p.63 “When copy-
ing onto custom size paper” The
sizes that you can input are as fol-
lows.
Metric
version
•
•
Vertical: 90 – 305mm
Horizontal: 148 – 432mm *1
Inch
version
•
•
Vertical: 3.6" – 12.0"
Horizontal: 5.9" – 17.0" *1
*1
Paper size up to 600mm(23.6") is
available when an optional HDD is
installed.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ Swing out the extender to sup-
port paper sizes larger than
A4L, 81/2" × 11"L.
B Push up the paper guide release
lever.
❒ Fan paper to get air between the
sheets and avoid a multi-sheet
feed.
❒ Before setting, adjust the paper
if curled or warped.
2
D Push down the paper guide re-
lease lever.
"Bypass" is selected automatically.
1: Paper guide release lever
C Lightly insert the copy paper face
down and adjust the paper guide.
The k indicator on the display au-
tomatically goes on.
When copying onto standard size
paper
A Press the {#} key.
B Press the [Select Size] key.
1: Extender
2: Paper guide
Important
❒ If the guides are not flush with
the copy paper, images might
be skewed or paper misfeed
might occur.
Note
❒ Do not stack paper over the lim-
it mark, otherwise images
might be skewed or paper mis-
feed might occur.
❒ Set the direction of the copy pa-
per to L.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying from the Bypass Tray
C Select the paper size.
Limitation
❒ Paper will be automatically de-
livered to the Internal tray.
A Press the {#} key.
B Press the [Custom Size] key.
2
C Press the [Vertical inch] key, en-
ter the vertical size of the paper
with the number keys, and
then press the [#] key.
Note
❒ The copy paper sizes that can
be selected are as follows:
• A3
A6
card
81/2
71/4
81/2
11 14
10
15L, 81/4
101/2KL, 8
8KL, 16KL, 37/8"
41/8" 91/2"L, C5 EnvL, C6
Env , DL Env
D Press the [OK] key.
L
L
L
×
×
,B4
, B5KL, B6
, 11
17L, 81/2
11KL, 51/2 81/2L
101/2KL, 8
13
13L, 81/4
13
, 11 15 , 10
14
10KL
71/2"L
L
,A4KL,A5KL
,
L
, Post-
×
×
14
L
,
,
×
×
L,
×
×
K,
×
×
L
×
L
×
14
L
,
,
Note
×
L
❒ To change the number en-
tered, press the [Clear] or
{Clear/Stop} key and enter
the new number.
8
×
×
,
×
,
×
L
L
D Enter the horizontal size of the
paper with the number keys,
and then press the [#] key.
E Place your originals, and then
press the {Start} key.
Note
❒ If the [Horiz inch] key is not
highlighted, press the [Horiz
inch] key.
When copying onto custom size
paper
❒ To change the number en-
tered, press the [Clear] or
{Clear/Stop} key and enter
the new number.
Important
❒ You should specify the size of
copy paper to avoid paper mis-
feeds.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
E To register the custom size en-
B
Lightly insert the OHP transpar-
encies, thick paper, thin paper or
label paper (adhesive paper) face
down and adjust the paper guide.
tered, press the [Program] key
and then press the [Exit] key.
Note
The k indicator on the display
automatically goes on.
❒ If you do not register the cus-
tom size, go to step F.
❒ Only one custom size can be
2
stored.
❒ To recall the custom size
stored, press the [Recall] key.
❒ If you do not register the cus-
tom size, the size you set is
deleted when modes are
cleared.
F Press the [OK] key.
Important
G Place your originals, and then
❒ If the guides are not flush
with the copy paper, images
might be skewed or paper
misfeed might occur.
press the {Start} key.
When copying onto special paper
❒ When you load an OHP
transparency, make sure that
its front and back faces are
properly positioned.
To make copies onto OHP transpar-
encies, thick paper, thin paper or la-
bel paper (adhesive labels), you
need to specify the paper type and
size. ⇒ p.62 “When copying onto
standard size paper”, p.63 “When
copying onto custom size paper”
❒ To avoid paper misfeeds, fan
the paper before loading it in
the tray.
C Push down the paper guide re-
Note
lease lever.
❒ Select [Thick Paper] if the paper
weight is 105g/m2 (28 lb.) or
more.
"Bypass" is selected automati-
cally.
A Open the bypass tray, and push
D Press the {#} key.
up the paper guide release lever.
Display for "Bypass Tray Paper"
is shown.
E Select paper type in "Special
paper".
1: Paper guide release lever
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying from the Bypass Tray
F Press the [OK] key.
C Push down the green lever of
the fusing unit as shown in the
illustration.
G Place your originals, and then
press the {Start} key.
Important
❒ When copying onto OHP
transparencies, remove cop-
ied sheets one by one.
2
When copying onto envelopes
A If the duplex unit is installed,
open the duplex unit by lifting
the catch.
ZEWH320E
Important
❒ Be sure to return the lever to
the original position, after
you have finished copying
on envelopes.
❒ If you copy on plain paper
without returning the lever
to the original position, the
copy quality might be re-
duced.
D Close the right cover.
B Open the right cover by lifting
the catch.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
E If the duplex unit is installed,
close the duplex unit.
2
F Press the {#} key.
G Select the paper size, and then
select [Thick Paper] for the paper
type.
H Press the [OK] key.
I Place your originals, and then
press the {Start} key.
E When your copy job is finished,
press the {Clear Modes} key to
clear the settings.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Programs
Programs
You can store frequently used copy
job settings in machine memory and
recall them for future use.
Storing a Program
A Edit the copy settings so that all
functions you want to store in this
program are selected.
❖
Storing Your Settings
You can store the settings you fre-
quently use.
2
B Press the {Program} key.
❖
❖
Deleting A Program
You can delete a stored program.
Recalling A Program
You can recall a stored program.
Note
C Press the [Register] key.
❒ You can store up to 10 programs.
❒ You can select the standard mode
or program No. 10 as the mode to
be set when modes are cleared or
reset, or immediately after the op-
eration switch is turned on. ⇒
“Change Initial Mode” on p.187
“General Features 2/4”
❒ Paper settings are stored based on
paper size. So if you place more
than one paper tray of the same
size, the paper tray prioritized
with the User Tools (System Set-
tings) will be selected first. Refer to
the System Settings manual.
D Press the program number you
want to store.
Note
❒ Program numbers with m al-
ready have settings in them.
❒ Programs are not cleared by turn-
ing the power off or by pressing
the {Clear Modes} key. They are
canceled only when you delete or
overwrite them with another pro-
gram.
Reference
⇒ p.68 “Changing a stored pro-
gram”
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
E Enter the program name with the B Repeat steps to in Storing a
A
D
letter keys on the display panel.
Program.
2
Note
To overwrite the program
❒ If you do not wish to enter the
program name, go to step .
F
Important
❒ You can register up to 40 char-
❒ If you select [Register], the previ-
acters.
ous program is lost.
❒ To change the name entered,
A Repeat steps E and F in Storing
press the [
], [Delete All]
Back}spkaecey and enter
a Program.
or {Clear/Stop
new letters.
Not to overwrite the program
Reference
For details on entering charac-
ters, ⇒ "Entering Text Charac-
ters" in the System Settings
manual.
A Press the [Do not Register] key.
F Press the [OK] key.
When the settings are successfully
stored, the m indicator goes on.
Changing a stored program
A Check the program settings.
Note
❒ When you want to check the
contents of a program, recall the
program. ⇒ p.69 “Recalling a
Program”
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Programs
Deleting a Program
Recalling a Program
A Press the {Program} key.
A Press the {Program} key.
2
B Press the [Delete] key.
B Press the [Recall] key.
C Press the program number you C Press the program number you
want to delete.
want to recall.
The stored settings are displayed.
D Press the [Yes] key.
Note
❒ Only programs with m contain
a program.
D Place your originals, and then
press the {Start} key.
Note
❒ To cancel the deletion, press the
[
No] key.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Job Preset
The optional HDD is required to use this function.
If a long copy job is in progress and
D Press the [To "Printing"] key.
you do not wish to wait for it to finish,
you can use this function to set up the
next copy job in advance. When the
current copy job is finished, your
copy job will be started automatically.
After the current copy job, the next
job starts automatically.
2
Note
❒ You can switch the display to
the current copy job by pressing
the [To "Printing"] key. You can
switch the display to the preset
job by pressing the [To "Reserv-
ing"] key.
A Press the [Next Job] key when
"Copying" is shown.
B Set up the next copy job.
Note
❒ To cancel this job, press the
[
Cancel] key.
C Place the originals in the docu-
ment feeder, and then press the
{Start} key.
All originals are scanned.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
Other Functions
Energy Saver Mode
Interrupt Copy
If you do not operate the machine for
a certain period after copying or
when you press the {Energy Saver}
key, the display disappears and the
machine enters Energy Saver mode.
When you press the {Energy Saver}
key again, the machine returns to the
ready condition. In Energy Saver
mode, the machine uses less electrici-
ty.
Use this function if you wish to inter-
rupt a long copy job to make urgently
needed copies.
2
Limitation
❒ You cannot use the Interrupt Copy
function when scanning fax origi-
nals.
Note
❒ The procedure for making inter-
rupt copies depends on which
kind of operation the machine is
currently carrying out.
Note
❒ If you press the {Energy Saver} key
during an operation, the current
settings will be cleared.
To interrupt an original being fed by the
document feeder
❒ It takes about 3 seconds to return
to the ready condition from Energy
Saver mode.
A Press the {Interrupt} key.
Reference
The Interrupt indicator goes on
and scanning stops.
⇒"Low Power Timer" in the Sys-
tem Settings manual
B Remove the originals that were
being copied and place the origi-
nals you wish to copy.
C Press the {Start} key.
The machine starts making your
copies.
D When your copy job is finished,
remove your originals and copies.
E Press the {Interrupt} key again.
The Interrupt indicator goes off.
F When the display prompts you,
replace the originals that were be-
ing copied before.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
G Press the {Start} key.
Sample Copy
Note
Use this function to check a copy set
before making a long copy run.
❒ The previous copy job settings
will be restored and the ma-
chine will continue copying
from where it left off.
Limitation
❒ This function can be used only
when the Sort function has been
turned on.
2
To interrupt copying after all originals
have been fed by the document feeder
A Select Sort and any other func-
tions, and then enter the number
of copy sets to be made.
A Press the {Interrupt} key.
The Interrupt indicator goes on.
B Place the originals.
Note
C Press the {Sample Copy} key.
❒ Copying will not stop yet.
One copy set is delivered as a sam-
ple.
B Place your original.
C Press the {Start} key.
D After checking the results, press
the [Print] key if the sample is ac-
ceptable.
The machine stops the original job
and starts copying your original.
The number of copies made is the
number you specified minus one
for the proof copy.
D When copying is complete, re-
move your originals and copies.
E Press the {Interrupt} key again.
Note
The Interrupt indicator goes off.
❒ If you press the [Suspend] key
The previous copy job settings will
be restored and the machine will
continue copying from where it
left off.
after checking the results, re-
turn to step to adjust the copy
A
settings as necessary. You can
change the settings for Staple,
Duplex, Copy Orientation,
Stamp, Margin Adjust, and
Cover/Slip Sheet. However, de-
pending on the combination of
functions, you may not be able
to change some settings.
Original Beeper
The beeper sounds and an error mes-
sage is displayed when you leave
your originals on the exposure glass
after copying.
❒ You cannot use the Sample
Copy function after changing
the settings.
Note
❒ To cancel this function, ⇒ "Tone:
Original remains" on p.187 “Gen-
eral Features 2/4”.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
C Enter the number of copy sets
with the number keys, and then
press the {#} key.
Changing the Number of Sets
You can change the number of copy
sets during copying.
Limitation
❒ This function can be used only
when the Sort function has been
turned on.
2
A Press the {Clear/Stop} key when
"Copying" is displayed.
Note
❒ The number of sets you can en-
ter differs depending on when
the {Clear/Stop} key was
pressed.
❒ To change the entered number,
press the {Clear/Stop} key.
D Press the [Continue] key.
B Press the [Change Quantity] key.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Preset Reduce/Enlarge
You can select a preset ratio for copy-
ing.
❒ You can select a ratio regardless of
the size of an original or copy pa-
per. With some ratios, parts of the
image might not be copied or mar-
gins will appear on copies.
2
❒ Copies can be reduced or enlarged
as follows.
❖
Metric version
Original → Copy
paper size
Ratio (%)
400 (enlarge area
by 16)
--
Note
❒ The reproduction ratios that you
can specify are 25-400% (25-200%
when placing originals in the doc-
ument feeder).
200 (enlarge area
by 4)
A5→A3
141 (enlarge area
by 2)
A4→A3, A5→A4
❒ You can select one of 12 preset ra-
tios (5 enlargement ratios, 7 reduc-
tion ratios).
122
115
93
F→A3, A4→B4
B4→A3
❒ Use "Create Margin" to reduce the
image to 93% of its original size
with the center as reference. You
can register this function in a
shortcut key on the initial display.
⇒ "Copy Function Key: F1-F5" on
p.189 “General Features 3/4”
--
82
F→A4, B4→A4
B4→F4, B4→F
75
71 (reduce area by A3→A4, A4→A5
1/2)
65
A3→F
❒ You can change the preset ratios to
other ratios you frequently use. ⇒
"Enlarge 1-5" on p.191 “Reproduc-
50 (reduce area by A3→A5, F→A5
1/4)
1
25
--
tion Ratio /2” and "Reduce 1–6"
on p.192 “Reproduction Ratio 2/2”
❒ You can set and display three ra-
tios on the initial display. ⇒
"Shortcut R/E" on p.191 “Repro-
duction Ratio 1/2”
❒ You can specify if [Reduce], [En-
large] or [Mag. Ratio] is to be given
priority and displayed when the
[
Reduce/Enlarge] key is pressed. ⇒
"R/E Priority" on p.192 “Repro-
duction Ratio 2/2”
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset Reduce/Enlarge
❖
Inch version
B Press the [Enlarge] or [Reduce] key.
Ratio (%)
Original → Copy
paper size
400 (enlarge area
by 16)
--
200 (enlarge area
by 4)
51/2" ×81/2"→11" ×
17"
2
155 (enlarge area
by 2)
51/2" ×
81/2"→81/2" × 14"
129
81/2" × 11"→11" ×
17"
C Select a ratio.
121
81/2" × 14"→11" ×
17"
D Press the [OK] key.
E Place your originals, and then
93
85
78
--
press the {Start} key.
F→81/2" × 11"
81/2" ×14"→81/2" ×
11"
73
65
11" × 15"→81/2" ×
11"
11" × 17"→81/2" ×
11"
50 (reduce area by 11" × 17"→51/2" ×
1/4)
25
81/2"
--
A Press the [Reduce/Enlarge] key.
Note
❒ To select a preset ratio on the in-
itial display, press the shortcut
reduce/enlarge key and go to
step .
D
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Create Margin Mode
Use "Create Margin" to reduce the im-
age to 93% of its original size with the
center as reference. You can register
this function in a shortcut key on the
initial display. By combining it with
the Reduce/Enlarge function, you
can also provide the Reduce/Enlarge
copy with a margin.
2
Note
❒ You can register "Create Margin"
in a shortcut key. ⇒ "Copy Func-
tion Key: F1-F5" on p.189 “General
Features 3/4”
❒ You can change the Reduce/En-
large ratio for "Create Margin". ⇒
"Ratio for Create Margin" on p.192
“Reproduction Ratio 2/2”
A Press the [Create Margin] key dis-
played on the initial display.
B If you do not wish to combine it
with the Reduce/Enlarge func-
tion, place your originals, and
then press the {Start} key.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Zoom
Zoom
You can change the reproduction ra-
tio in 1% steps.
B Enter the ratio.
To select the ratio with the [n]
and [o] keys
2
A Select a preset ratio which is
close to the desired ratio by us-
ing [Reduce] or [Enlarge].
Note
❒ The reproduction ratios that you
can specify are 25-400% (25-200%
when placing originals in the doc-
ument feeder).
❒ You can select a ratio regardless of
the size of an original or copy pa-
per. With some ratios, parts of the
image might not be copied or mar-
gins will appear on copies.
B Adjust the ratios with the [n]
or [o] key.
Note
❒ To change the ratio in 1%
steps, just press the [n] or
[o] key. To change the ratio
in 10% steps, press and hold
down the [n] or [o] key.
❒ You can select a preset ratio which
is near the desired ratio, then ad-
just the ratio with the [n] or [o]
key.
❒ If you have incorrectly en-
tered the ratio, readjust the
ratio with the [n] or [o]
key.
A Press the [Reduce/Enlarge] key.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
To enter the ratio with the number
keys
A Press the [Mag. Ratio] key.
2
B Enter the desired ratio with the
number keys.
Note
❒ To change the ratio entered,
press the [C l e a r] or
{Clear/Stop} key and enter
the new ratio.
C Press the [#] key.
D Press the [OK] key.
C Place your originals, and then
press the {Start} key.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Size Magnification
Size Magnification
This function calculates an enlarge-
ment or reduction ratio based upon
the lengths of the original and copy.
B Press the [Specifd. Ratio] key.
2
Amm
amm
C Make sure that the [Specifd. Ratio
]
key is highlighted.
Preparation
D Enter the length of the original
Measure and specify the lengths of
the original and copy by compar-
ing "A" with "a."
with the number keys, and then
press the [#] key.
Limitation
❒ If the calculated ratio is over the
maximum or under the minimum
ratio, it is adjusted to within the
available range of ratios automati-
cally. However, with some ratios,
parts of the image might not be
copied or margins will appear on
copies.
Note
❒ You can enter sizes within the
Note
following ranges.
❒ A ratio is selected in the range of 25
to 400% (25-200% when placing
originals in the document feeder).
Metric 1 – 999mm (in 1mm steps)
version
Inch
version
0.1" – 99.9" (in 0.1" steps)
A Press the [Reduce/Enlarge] key.
❒ To change the length entered,
press the [Clear] or {Clear/Stop}
key and enter the new length.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
E Enter the length of the copy with
the number keys, and then press
the [#] key.
Note
❒ To change the length entered,
press the [Clear] or {Clear/Stop}
key and enter the new length.
2
❒ To change the length after
pressing the [#] key, select [Orig-
inal] or [Copy] and enter the de-
sired length.
F Press the [OK] key.
G Press the [OK] key.
H Place your original, and then
press the {Start} key.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Directional Magnification (%)
Directional Magnification (%)
Copies can be reduced or enlarged at
different reproduction ratios horizon-
tally and vertically.
B Press the [Specifd. Ratio] key.
a%
2
b%
C Press the [Direct. Mag.%] key.
CP2P01EE
a: Horizontal ratio
b: Vertical ratio
Note
❒ The reproduction ratios that you
can specify are 25-400% (25-200%
when placing originals in the doc-
ument feeder).
❒ You can select a ratio regardless of
the size of an original or copy pa-
per. With some ratios, parts of the
image might not be copied or mar-
gins will appear on copies.
To enter the ratio with the number
keys
A Press the [Horizontal] key.
❒ You can also select a preset ratio
which is close to the desired ratio
by using [Reduce] or [Enlarge], then
adjust the ratio with the [n] or
[o] key.
A Press the [Reduce/Enlarge] key.
B Enter the desired ratio with the
number keys, followed by the
[
#] key.
Note
❒ To change the ratio entered,
press the [Clear] or {Clear/Stop}
key and enter the new ratio.
C Press the [Vertical] key.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
D Enter the desired ratio with the
number keys, followed by the
] key.
[
#
E Press the [OK] key.
To specify a ratio with the [n]
and [o] keys
2
A Press the [With no] key.
B Press the [Horizontal] key.
C Adjust the ratio using the [n]
or [o] key.
Note
❒ Pressing the [n] or [o] key
changes the ratio in 1% steps.
Pressing and holding down
the [n] or [o] key changes it
in 10% steps.
❒ If you have incorrectly en-
tered the ratio, readjust the
ratio with the [n] or [o]
key.
D Press the [Vertical] key.
E Adjust the ratio with the [n]
or [o] key.
F Press the [OK] key.
D Press the [OK] key.
E Place your originals, and then
press the {Start} key.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Directional Size Magnification (Inch)
Directional Size Magnification (Inch)
The suitable reproduction ratios will
be automatically selected when you
enter the horizontal and vertical
lengths of the original and copy im-
age you require.
❒ The reproduction ratios that you
can specify are 25-400% (25-200%
when placing originals in the doc-
ument feeder).
A Press the [Reduce/Enlarge] key.
B Press the [Specifd. Ratio] key.
C Press the [Dirc.Size Mag.In] key.
2
1
3
2
4
CP2M01EE
1: Horizontal original size
2: Vertical original size
3: Horizontal copy size
4: Vertical copy size
Preparation
Specify the vertical and horizontal
sizes of the original and those of the
copy, as shown in the illustration.
Limitation
❒
If the calculated ratio is over the
maximum or under the minimum
ratio, it is adjusted to within the
available range of ratios automatical-
ly. However, with some ratios, parts
of the image might not be copied or
margins will appear on copies.
Note
❒ You can enter sizes within the fol-
lowing ranges.
D Enter the horizontal size of the
original with the number keys,
Metric Vertical: 1 – 999mm (in 1mm
version steps)
and then press the [#] key.
Horizontal: 1 – 9999 (in 1mm
steps)
Note
❒ To change the value entered,
press the [Clear] or {Clear/Stop}
key and enter the new value.
Inch
version
0.1" – 99.9" (in 0.1" steps)
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
E Enter the horizontal size of the
copy with the number keys, and
then press the [#] key.
F Enter the vertical size of the origi-
nal with the number keys, and
then press the [#] key.
2
G Enter the vertical size of the copy
with the number keys, and then
press the [#] key.
Note
❒ To change a length, press the
key you wish to change and en-
ter the new value.
H Press the [OK] key.
I Press the [OK] key.
J Place your originals, and then
press the {Start} key.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Duplex/Combine/Series
Duplex/Combine/Series
You can make copies in a variety of
formats by combining the following
modes:
B Select [1 Sided] or [2 Sided] for cop-
ying.
• 1 Sided/2 Sided originals
• 1 Sided/2 Sided copies
• Duplex
1
2
2
• Combine
• Book
• Series
A Press [Dup./Combine/Series], check
your originals, and then select [
1
Sided] or [2 Sided] for the originals.
1
3
2
4
1
5
2
6
3
7
4
8
1
2
1
2
1
3
2
5
6
8
1
5
2
6
3
7
4
8
4
3
4
7
9
10 11 12
13 14 15 16
1: 1-sided
2: 2-sided
A: Front
B: Back
1: 1-sided
2: 2-sided
3: Series/Book
C Press the [OK] key.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Original Direction and
Completed Copies
Originals and Copy Direction
You can select the orientation ([Top to
Top], [Top to Bottom]). ⇒ p.86 “Specify-
ing Orientation of Bound Originals”
The resulting copy image will differ
according to the direction in which
you place your original (widthwise
K or lengthwise L).
• Top to Top
2
Duplex1
• Top to Bottom
Duplex2
Specifying Orientation of
Bound Originals
You can specify the orientation of
bound originals (how you turn the
pages). The default setting is [Top to
Top].
Note
GCRYOU1E
❒ You can change the orientation de-
fault with the User Tools. ⇒ "Copy
Orientation in Duplex Mode" and
"Original Orientation in Duplex
Mode" on p.187 “General Features
2/4”
Note
❒ The table shows the orientation of
images on the front and back of
copies, not the direction of deliv-
ery.
A Press the [Dup./Combine/Series] key.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Duplex/Combine/Series
B Press the [Orientation] key.
2
C Select an original orientation and
a copy orientation.
D Press the [OK] key.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Duplex
The optional Duplex unit is required to use this function.
This function can be used in two
ways:
1 Sided
→
2 Sided
❖
1 Sided
→
2 Sided
2
This mode makes two-sided copies
from one-sided originals.
❖
2 Sided
→
2 Sided
1
2
1
This mode makes two-sided copies
from two-sided originals.
2
Limitation
❒ You cannot use the following copy
paper with this function:
• Paper smaller than A5K, 51/2"
× 81/2"K (possible on A5L,
51/2" × 81/2"L)
Note
❒ If you set an odd number of 1-sid-
ed originals in the document feed-
er, the reverse side of the last page
is left blank.
• Paper thicker than 90g/m2, 24
lb.
• Paper thinner than 64g/m2, 20
❒ When original images are copied,
the images are shifted by the width
of the binding margin. You can ad-
just the binding margin or binding
position. You can also change their
default values. ⇒ "Front Margin:
Left/Right ", "Back Margin:
Left/Right", "Front Margin:
Top/Bottom " and "Back Margin:
Top/Bottom" on p.194 “Edit 1/2”
lb.
• Translucent paper
• Label paper (adhesive labels)
• OHP transparencies
• Postcards
❒ You cannot use the bypass tray
with this function.
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or
HDD is required.
❒ By default, a binding margin is
made on the back side. You can
change the value of this setting. ⇒
"1 sided → 2 sided Auto Margin: T
to T" on p.194 “Edit 1/2”
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Duplex
B Place the next original. When it
is placed on the exposure glass,
press the {Start} key.
A Press the [Dup./Combine/Series] key.
Note
❒ When using the SADF func-
tion the original is automati-
cally fed each time it is
placed without pressing the
{Start} key. ⇒ p.35 “SADF
mode”
2
C Press the {#} key after the last
B Press the [1 Sided] key for "Origi-
original has been scanned.
nal", and then press the [2 Sided
]
key for "Copy".
2 Sided
→
2 Sided
1
1
2
2
Note
❒ To change the copy orientation
to "Top to Bottom", press the [Ori-
entation] key and select [Top to
Bottom]. ⇒ p.86 “Specifying Ori-
entation of Bound Originals”
A Press the [Dup./Combine/Series] key.
C Press the [OK] key.
D Place your originals, and then
press the {Start} key.
When placing an original on the
exposure glass or in the document
feeder using Batch mode
Reference
⇒ p.34 “Batch mode”
A Place the original, and then
press the {Start} key.
Note
❒ Start with the first page to be
copied.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
C Press the {#} key after the last
B Press the [2 Sided] key for "Origi-
original has been scanned.
nal", and then press the [2 Sided
]
key for "Copy".
2
Note
❒ To change the copy orientation
to "Top to Bottom", press the [Ori-
entation] key and select [Top to
Bottom]. ⇒ p.86 “Specifying Ori-
entation of Bound Originals”
C Press the [OK] key.
D Place your originals, and then
press the {Start} key.
When placing an original on the
exposure glass or in the document
feeder using Batch mode
Reference
⇒ p.34 “Batch mode”
A Place the original, and then
press the {Start} key.
Note
❒ Start with the first page to be
copied.
B Place the next original. When it
is placed on the exposure glass,
press the {Start} key.
Note
❒ When using the SADF func-
tion the original is automati-
cally fed each time it is
placed without pressing the
{Start} key. ⇒ p.35 “SADF
mode”
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Combine
Combine
You can combine two or more origi-
nals into one copy. 1 Sided Combine
mode is for 1-sided copies, and 2 Sid-
ed Combine mode for 2-sided copies.
❖
❖
❖
2 Sided 4 Pages
(The optional Duplex unit is required
to use this function.)
Copies two 2-sided originals to
one sheet with two pages per side.
→
Combine 2 Side
Thisfunction canbeused intwelveways:
2
2 Sided 8 Pages
(The optional Duplex unit is required
to use this function.)
Copies four 2-sided originals to
one sheet with four pages per side.
→
Combine 2 Side
❖
❖
❖
❖
1 Sided 2 Pages
Copies two 1-sided originals to
one side of a sheet.
→
Combine 1 Side
1 Sided 4 Pages
Copies four 1-sided originals to-
gether to one side of a sheet.
→
Combine 1 Side
2 Sided 16 Pages
(The optional Duplex unit is required
to use this function.)
Copies eight 2-sided originals to
one sheet with eight pages per
side.
→
Combine 2 Side
1 Sided 8 Pages
Copies eight 1-sided originals to-
gether to one side of a sheet.
→
Combine 1 Side
1 Sided 4 Pages
(The optional Duplex unit is required
to use this function.)
→
Combine 2 Side
Limitation
❒ You cannot use the bypass tray
Copies four 1-sided originals to
one sheet with two pages per side.
with this function.
❒ If the calculated ratio is under the
minimum ratio, it is adjusted to
within the available range of ratios
automatically. However, with
some ratios, parts of the image
might not be copied.
❖
❖
1 Sided 8 Pages
(The optional Duplex unit is required
to use this function.)
Copies eight 1-sided originals to
one sheet with four pages per side.
→
Combine 2 Side
❒ You cannot use custom size paper.
1 Sided 16 Pages
(The optional Duplex unit is required
to use this function.)
→
Combine 2 Side
Note
❒ In this mode, the machine selects
the reproduction ratio automati-
cally. This reproduction ratio de-
pends on the copy paper sizes and
the number of originals.
Copies 16 1-sided originals to one
sheet with eight pages per side.
❖
❖
❖
2 Sided 2 Pages
Copies one 2-sided original to one
side of a sheet.
→
Combine 1 Side
❒ The reproduction ratios that you
can specify are 25-400% (25-200%
when placing originals in the doc-
ument feeder).
2 Sided 4 Pages
Copies two 2-sided originals to
one side of a sheet.
→
Combine 1 Side
❒ A separation line between origi-
nals can be printed with the User
Tools. ⇒ "Separation Line in Com-
bine" on p.196 “Edit 2/2”
2 Sided 8 Pages
Copies four 2-sided originals to
one side of a sheet.
→
Combine 1 Side
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ If the direction of originals is dif-
ferent from that of the copy paper,
the machine will automatically ro-
tate the image by 90° to make cop-
ies properly.
1 Sided 2 Pages
Side
→
Combine 1
Copies two 1-sided originals to one
side of a sheet.
❒ When making copies in Combine
mode, the border of each original
can be automatically erased by
3mm, 0.1". ⇒ "Erase Original
Shadow in Combine" on p.194
“Edit 1/2”
2
1
2
1
2
❒ If the number of originals placed is
less than the number specified for
combining, the last page is left
blank as shown in the illustration.
❖
Placing originals (Originals placed in
the document feeder)
1
2
1
3
2
3
• Originals read from left to right
❒ You can change the copy order in
Combination mode. ⇒ "Copy Or-
der In Combine" on p.196 “Edit
2/2”
1
2
1
2
3
3
4
4
Combine5
❒ See the following illustration for
direction of the originals and ar-
rangement of combined images.
• Originals read from top to bot-
tom
❖
Open to Left (
K) originals
1
2
1
2
1
3
2
4
3
1
2
6
3
7
4
8
4
1
2
5
8
Combine6
GCSHUY1E
❖
Open to Right (
L
) originals
1
2
1
3
5
7
2
4
6
8
1
2
8
GCSHUY2E
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Combine
A Press the [Dup./Combine/Series] key.
1 Sided 4 Pages
Side
→
Combine 1
Copies four 1-sided originals together
to one side of a sheet.
2
1
2
3
1
3
2
4
4
B Press the [1 Sided] key for "Origi-
nal", and then press the [Combine 1
Side] key for "Copy".
E
A Press the [Dup./Combine/Series] key.
C Press the [2 Originals] key, and
then press the [OK] key.
B Press the [1 Sided] key for "Origi-
nal", and then press the [Combine 1
Side] key for "Copy".
D Select the paper.
E Place your originals, and then
press the {Start} key.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
C Press the [4 Originals] key, and
1 Sided 8 Pages
Side
→
Combine 1
then press the [OK] key.
Copies eight 1-sided originals togeth-
er to one side of a sheet.
1
2
2
1
5
2
6
3
7
4
8
7
8
D Select the paper.
A Press the [Dup./Combine/Series] key.
E Place your originals, and then
press the {Start} key.
B Press the [1 Sided] key for "Origi-
nal", and then press the [Combine 1
Side] key for "Copy".
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Combine
C Press the [8 Originals] key, and
1 Sided 4 Pages
Side
→
Combine 2
then press the [OK] key.
Copies four 1-sided originals to one
sheet with two pages per side.
2
1
2
1
2
3
4
4
3
D Select the paper.
Limitation
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or a
HDD is required.
E Place your originals, and then
A Press the [Dup./Combine/Series] key.
press the {Start} key.
B Press the [1 Sided] key for "Origi-
nal", and then press the [Combine 2
Side] key for "Copy".
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
C Press the [4 Originals] key, and
1 Sided 8 Pages
Side
→
Combine 2
then press the [OK] key.
Copies eight 1-sided originals to one
sheet with four pages per side.
1
2
2
1
3
2
4
5
7
6
8
7
8
D Check the orientation.
1
2
GCSHVYAE
1: Front
2: Back
Limitation
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or a
HDD is required.
Note
❒ To change the copy orientation
to "Top to Bottom", press the
[
Orientation] key and select [Top
A Press the [Dup./Combine/Series] key.
to Bottom]. ⇒ p.86 “Specifying
Orientation of Bound Origi-
nals”
E Press the [OK] key.
F Select the paper.
G Place your originals, and then
press the {Start} key.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Combine
B Press the [1 Sided] key for "Origi-
nal", and then press the [Combine 2
Side] key for "Copy".
1 Sided 16 Pages
2 Side
→
Combine
Copies sixteen 1-sided originals to
one sheet with eight pages per side.
1
1
5
2
6
3
7
4
8
2
2
1
15
16
9 10 11 12
C Press the [8 Originals] key, and
13 14 15 16
then press the [OK] key.
2
GCSHVY5E
1: Front
2: Back
Limitation
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or a
HDD is required.
D Check the orientation.
A Press the [Dup./Combine/Series] key.
Note
❒ To change the copy orientation
to "Top to Bottom", press the [Ori-
entation] key and select [Top to
Bottom]. ⇒ p.86 “Specifying Ori-
entation of Bound Originals”
E Press the [OK] key.
F Select the paper.
G Place your originals, and then
press the {Start} key.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
B Press the [1 Sided] key for "Origi-
nal", and then press the [Combine 2
Side] key for "Copy".
2 Sided 2 Pages
Side
→
Combine 1
Copies one 2-sided original to one
side of a sheet.
2
1
1
2
2
C Press the [16 Originals] key, and
then press the [OK] key.
A Press the [Dup./Combine/Series] key.
D Check the orientation.
B Press the [2 Sided] key for "Origi-
nal", and then press the [Combine 1
Side] key for "Copy".
Note
❒ To change the copy orientation
to "Top to Bottom", press the [Ori-
entation] key and select [Top to
Bottom]. ⇒ p.86 “Specifying Ori-
entation of Bound Originals”
E Press the [OK] key.
F Select the paper.
G Place your originals, and then
press the {Start} key.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Combine
C Press the [2 Pages] key, and then
2 Sided 4 Pages
Side
→
Combine 1
press the [OK] key.
Copies two 2-sided originals to one
side of a sheet.
2
1
3
1
3
2
4
2
4
D Check the orientation.
A Press the [Dup./Combine/Series] key.
Note
❒ To change the copy orientation
to "Top to Bottom", press the
[
Orientation] key and select [Top
to Bottom]. ⇒ p.86 “Specifying
Orientation of Bound Origi-
nals”
B Press the [2 Sided] key for "Origi-
nal", and then press the [Combine 1
Side] key for "Copy".
E Press the [OK] key.
F Select the paper.
G Place your originals, and then
press the {Start} key.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
C Press the [4 Pages] key, and then
2 Sided 8 Pages
Side
→
Combine 1
press the [OK] key.
Copies four 2-sided originals to one
side of a sheet.
2
1
3
1
5
2
6
3
7
4
8
5
2
7
4
6
D Check the orientation.
8
A Press the [Dup./Combine/Series] key.
Note
❒ To change the copy orientation
to "Top to Bottom", press the
[
Orientation] key and select [Top
to Bottom]. ⇒ p.86 “Specifying
Orientation of Bound Origi-
nals”
B Press the [2 Sided] key for "Origi-
nal", and then press the [Combine 1
Side] key for "Copy".
E Press the [OK] key.
F Select the paper.
G Place your originals, and then
press the {Start} key.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Combine
C Press the [8 Pages] key, and then
2 Sided 4 Pages
Side
→
Combine 2
press the [OK] key.
Copies two 2-sided originals to one
sheet with two pages per side.
2
1
1
2
3
2
4
3
4
D Check the orientation.
Limitation
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or a
HDD is required.
Note
A Press the [Dup./Combine/Series] key.
❒ To change the copy orientation
to "Top to Bottom", press the
[
Orientation] key and select [Top
to Bottom]. ⇒ p.86 “Specifying
Orientation of Bound Origi-
nals”
E Press the [OK] key.
F Select the paper.
G Place your originals, and then
B Press the [2 Sided] key for "Origi-
nal", and then press the [Combine 2
Side] key for "Copy".
press the {Start} key.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
C Press the [4 Pages] key, and then
2 Sided 8 Pages
Side
→
Combine 2
press the [OK] key.
Copies four 2-sided originals to one
sheet with four pages per side.
2
1
3
1
3
2
4
5
7
6
8
5
2
7
D Check the orientation.
4
6
1
2
8
GCSHVY2E
1: Front
2: Back
Limitation
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or a
HDD is required.
Note
❒ To change the copy orientation
to "Top to Bottom", press the
[
Orientation] key and select [Top
to Bottom]. ⇒ p.86 “Specifying
Orientation of Bound Origi-
nals”
A Press the [Dup./Combine/Series] key.
E Press the [OK] key.
F Select the paper.
G Place your originals, and then
press the {Start} key.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Combine
B Press the [2 Sided] key for "Origi-
nal", and then press the [Combine 2
Side] key for "Copy".
2 Sided 16 Pages
2 Side
→
Combine
Copies eight 2-sided originals to one
sheet with eight pages per side.
1
1
5
2
6
3
7
4
8
3
2
2
4
1
13
15
9 10 11 12
C Press the [8 Pages] key, and then
14
13 14 15 16
16
press the [OK] key.
2
GCSHVY6E
1: Front
2: Back
Limitation
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or a
HDD is required.
D Check the orientation.
A Press the [Dup./Combine/Series] key.
Note
❒ To change the copy orientation
to "Top to Bottom", press the [Ori-
entation] key and select [Top to
Bottom]. ⇒ p.86 “Specifying Ori-
entation of Bound Originals”
E Press the [OK] key.
F Select the paper.
G Place your originals, and then
press the {Start} key.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
B Press the [2 Sided] key for "Origi- G Place your originals, and then
nal", and then press the [Combine 2
Side] key for "Copy".
press the {Start} key.
2
C Press the [16 Pages] key, and then
press the [OK] key.
D Check the orientation.
Note
❒ To change the copy orientation
to "Top to Bottom", press the
[
Orientation] key and select [Top
to Bottom]. ⇒ p.86 “Specifying
Orientation of Bound Origi-
nals”
E Press the [OK] key.
F Select the paper.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Series/Book
Series/Book
Series copies are made by separately
copying the front and back of a 2-sid-
ed original or the two facing pages of
a spread original onto two sheets of
paper. A book is made by copying
two or more originals in page order.
Series Copies
Book
→
1 Sided
2
You can make one-sided copies from
two facing pages of a bound original
(book).
The following types of Series and
Book modes can be used:
❖
Series Copies
Limitation
• Book→1 Sided
❒ You cannot use the Book→1 Sided
Copies the two facing pages of a
spread original to make two 1-
sided copies.
function with the document feeder.
• Book→2 Sided (The optional
Duplex unit is required to use
this function.)
1
2
1
2
Copies a spread two-page origi-
nal onto one sheet with one
page per side.
• Front & Back→ 2 Sided (The op-
tional Duplex unit is required to
use this function.)
Note
Copies each two-page spread
original as it is onto both sides
of a sheet.
❒ See the following table for original
and copy paper sizes when using a
100% ratio.
❖
Booklet (The optional Duplex unit is
required to use this function.)
❖
Metric version
Original
Copy paper
• 1 Sided→Booklet
A3L
B4L
A4L
A4K × 2 sheets
B5K × 2 sheets
A5K × 2 sheets
Make copies in page order for a
folded booklet.
• 2 Sided→Booklet
Copies a 2-sided original in
page order for a folded booklet.
❖
Inch version
• 1 Sided→Magazine
Original
Copy paper
Copies two or more originals to
make copies in page order (as
when they are folded and as-
sembled).
11" × 17"L
81/2" × 11"K × 2
sheets
81/2" × 11"L
51/2" × 81/2"K × 2
sheets
• 2 Sided→Magazine
Copies 2-sided originals to make
copies in page order (as when
they are folded and assembled).
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
A Press the [Dup./Combine/Series] key. F Make sure that the [Auto Paper Se-
lect] key is selected.
Note
❒ If the [Auto Paper Select] key is
not selected, press the [Auto Pa-
per Select] key.
2
G Place your originals on the expo-
sure glass, and then press the
{Start} key.
B Press the [Series/Book] key.
Book
→
2 Sided
Copies a two-page spread original
onto one sheet with one page per side.
Limitation
❒ You cannot use the Book→2 Sided
function with the document feeder.
C Make sure that the [Series] key is
selected.
1
2
1
2
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or a
HDD is required.
D Press the [Book
→1 Sided] key, and
then press the [OK] key.
Note
❒ See the following table for original
and copy paper sizes when using a
100% ratio.
❖
Metric version
Original
Copy paper
A4 (2-sided)
B5 (2-sided)
A5 (2-sided)
A3L
B4L
A4L
E Press the [OK] key.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Series/Book
❖
Inch version
D Press the [Book
→
2 Sided] key, and
then press the [OK] key.
Original
Copy paper
81/2" × 11" (2-sided)
11" × 17"L
81/2" × 11"L
51/2" 81/2" (2-sided)
×
A Press the [Dup./Combine/Series] key.
2
E Press the [OK] key.
F Select the paper.
G Place your originals on the expo-
sure glass, and then press the
{Start} key.
B Press the [Series/Book] key.
Front & Back
→
2 Sided
Copies each two-page spread original
as it is onto both sides of a sheet.
Limitation
❒ You cannot use the Front & Back →
2 Sided function with the docu-
ment feeder.
C Make sure that the [Series] key is
selected.
1
2
1
2
3
3
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or a
HDD is required.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Note
C Make sure that the [Series] key is
selected.
❒ See the following table for original
and copy paper sizes when using a
100% ratio.
❖
Metric version
Original
Copy paper
A4 (2-sided)
B5 (2-sided)
A5 (2-sided)
2
A3L
B4L
A4L
D Press the [Front & Back
→
2 Sided]
❖
Inch version
key, and then press the [OK] key.
Original
Copy paper
81/2" × 11" (2-sided)
11" × 17"L
81/2" × 11"L
51/2" 81/2" (2-sided)
×
A Press the [Dup./Combine/Series] key.
E Press the [OK] key.
F Select the paper.
G Place your originals on the expo-
sure glass, and then press the
{Start} key.
B Press the [Series/Book] key.
Note
❒ Press the {#} key after all origi-
nals are scanned.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Series/Book
1 Sided
→
Booklet
Copying Book Originals
Make copies in page order for a fold-
ed booklet as shown in the following
illustrations.
Limitation
❒ You cannot use the bypass tray
with this function.
❖
Open to Left
❒ The function might not work for
certain types of large size originals
(such as A3, 11" × 17"). In this case,
an optional 32MB memory or a
HDD is required.
2
1
2
3
2
3
4
Note
1
4
❒ The machine sets the reproduction
ratio automatically to meet the pa-
per size and copies the originals to-
gether onto the paper.
GCBOOK0E
❒ The machine uses ratios in the
range of 25 to 400% (25-200% when
placing originals in the document
feeder).
❖
Open to Right
1
2
3
❒ If the calculated ratio is under the
available minimum ratio, it will be
adjusted to the minimum ratio.
However, with some ratios, parts
of the image might not be copied.
3
2
4
4
1
❒ If the direction of originals is dif-
ferent from that of the copy paper,
the machine will automatically ro-
tate the image by 90° to make cop-
ies properly.
GCBOOK1E
Important
❒ Before selecting this function, se-
lect "Open to left" or "Open to
right" with the User Tools. ⇒ “Ori-
entation: Booklet, Magazine” on
p.196 “Edit 2/2”
❒ If the number of originals scanned
is less than a multiple of 4, the last
page is left blank.
❒ You can have a 3mm, 0.1" bound-
ing margin around all four edges
of the original left blank (erased).
⇒ "Erase Original Shadow in
Combine" on p.194 “Edit 1/2”
Note
❒ Four originals are copied onto each
sheet of copy paper.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
D Press the [1 Sided
→Booklet] key,
How to fold copies to make a booklet
and then press the [OK] key.
1
2
3
3
1
1
2
GCBOOK2E
E Press the [OK] key.
1: Open to Left
F Select the paper.
2: Open to Right
G Place your originals, and then
A Press the [Dup./Combine/Series] key.
B Press the [Series/Book] key.
C Press the [Book] key.
press the {Start} key.
Note
❒ When placing originals on the
exposure glass or in the docu-
ment feeder in Batch/SADF
mode, press the {#} key after all
originals are scanned.
2 Sided
→
Booklet
Make copies of 2–sided originals with
a page order for a folded booklet as
shown in the following illustrations.
❖
Open to Left
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Series/Book
❖
Open to Right
A Press the [Dup./Combine/Series] key.
2
B Press the [Series/Book] key.
Important
❒ Before selecting this function, se-
lect "Open to left" or "Open to
right" with the User Tools. ⇒ “Ori-
entation: Booklet, Magazine” on
p.196 “Edit 2/2”
Note
❒ Two 2–sided originals are copied
onto each sheet of copy paper.
C Press the [Book] key.
How to fold copies to make a booklet
1
2
3
3
1
1
D Press the [2 Sided
→Booklet] key,
and then press the [OK] key.
GCBOOK2E
1: Open to Left
2: Open to Right
E Press the [OK] key.
F Select the paper.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Note
G Place your originals, and then
press the {Start} key.
❒ Four originals are copied onto each
sheet of copy paper.
Note
❒ The copying may take some time
❒ When placing originals on the
exposure glass or in the docu-
ment feeder in Batch/SADF
mode, press the {#} key after all
originals are scanned.
after scanning originals.
How to fold and assemble copies to
make a magazine
2
❖
Open to Left
1 Sided
→
Magazine
Copies two or more originals to make
copies in page order when they are
folded and assembled.
7
1
5
5
3
1
3
❖
Open to Left
1
2
GCBOOK5E
2
7
4
5
7
1
8
3
6
❖
Open to Right
8
GCBOOK3E
5
3
7
5
1
1
3
❖
Open to Right
1
2
GCBOOK6E
7
2
5
4
3
7
8
8
1
6
A Press the [Dup./Combine/Series] key.
GCBOOK4E
Important
❒ Before selecting this function, se-
lect "Open to left" or "Open to
right" with the User Tools. ⇒ "Ori-
entation: Booklet, Magazine" on
p.196 “Edit 2/2”
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Series/Book
B Press the [Series/Book] key.
2 Sided
→
Magazine
Copies two or more 2–sided originals
to make copies in page order when
they are folded and assembled.
❖
Open to Left
Open to Right
Important
2
C Press the [Book] key.
❖
D Press the [1 Sided
→Magazine] key,
and then press the [OK] key.
❒ Before selecting this function, se-
lect "Open to left" or "Open to
right" with the User Tools. ⇒ "Ori-
entation: Booklet, Magazine" on
p.196 “Edit 2/2”
E Press the [OK] key.
F Select the paper.
Note
G Place your originals, and then
press the {Start} key.
❒ Two 2–sided originals are copied
onto each sheet of copy paper.
Note
❒ The copying may take some time
❒ When placing originals on the
exposure glass or in the docu-
ment feeder in Batch/SADF
mode, press the {#} key after all
originals are scanned.
after scanning originals.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
B Press the [Series/Book] key.
How to fold and assemble copies to
make a magazine
❖
Open to Left
2
7
1
5
5
3
1
3
C Press the [Book] key.
GCBOOK5E
❖
Open to Right
5
3
7
5
1
1
3
D Press the [2 Sided
→Magazine] key,
and then press the [OK] key.
GCBOOK6E
A Press the [Dup./Combine/Series] key.
E Press the [OK] key.
F Select the paper.
G Place your originals, and then
press the {Start} key.
Note
❒ When placing originals on the
exposure glass or in the docu-
ment feeder in Batch/SADF
mode, press the {#} key after all
originals are scanned.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit Image
Edit Image
❒ Part of a repeated image might not
be copied depending on copy pa-
per size, copy paper direction or
reproduction ratio.
Image Repeat
The original image is copied repeat-
edly.
❒
You can insert separation lines between
repeated images. "Image Repeat
Separation Line" on p.196 “Edit 2/2”
2
⇒
A Select the size of the copy paper
and the reproduction ratio.
B Press the [Edit/Stamp] key.
C Press the [Edit Image] key.
D Press the [Image Repeat] key.
Note
❒ The number of repeated images
depends on the original size, copy
paper size, and reproduction ratio.
See the following table.
❖
Original: A5
K
/Copy paper: A4
K
L
or Original: A5
L
/Copy paper A4
4 repeats (71%)
16 repeats (35%)
Repeat2
Repeat1
❖
Original: A5
K
/Copy paper: A4
L
K
or Original: A5
L
/Copy paper A4
2 repeats
(100%)
8 repeats
(50%)
32 repeats
(25%)
Repeat5
Repeat3
Repeat4
E Press the [OK] key.
F Press the [OK] key.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❖
Inch version
G Place your original, and then
press the {Start} key.
Original Size and Copy Paper Size
Direction
and Direction
81/2" × 11"K
81/2" × 11"L
11" × 17"L
51/2" × 81/2"L
51/2" × 81/2"K
81/2" × 11"K
Double Copies
One original image is copied twice on
one copy as shown in the illustration.
2
A Press the [Edit/Stamp] key.
B Press the [Edit Image] key.
C Press the [Double Copies] key.
Limitation
❒
The originals of size A5
L
(51/2"
×
81/2"L) cannot be detected properly
on the exposure glass. Be sure to se-
lect the copy paper manually or set
the originals in the document feeder.
❒ You cannot use the bypass tray
with this function.
Note
❒ You can insert separation lines be-
tween repeated images. ⇒ "Dou-
ble Copies Separation Line" on
p.196 “Edit 2/2”
❒ See the following table for original
and copy paper sizes when using a
100% ratio.
❖
Metric version
D Press the [OK] key.
E Press the [OK] key.
F Select the paper.
Original Size and Copy Paper Size
Direction
A5L
and Direction
A4K
A4K
A3L
A5K
A4L
G Place your originals, and then
press the {Start} key.
B5K
B4L
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit Image
❖
Inch version
Centering
Original
Original size and direction
placed on:
You can make copies with the image
moved to the center of the copy pa-
per.
11" × 17"L, 81/2" × 14"L,
Exposure
glass
81/2" × 11"KL, 10" ×14"L,
8" × 10"L
11" × 17"L, 81/2" × 14"L,
81/2" × 11"KL, 10" ×14"L,
51/2" × 81/2"L
Document
feeder
2
A Select the paper.
B Press the [Edit/Stamp] key.
Limitation
❒ You cannot use the bypass tray
with this function.
❒ If the direction of originals is dif-
ferent from that of the copy paper,
the machine will not rotate the im-
age by 90°(rotated copy).
❒ If the original size cannot be meas-
ured, the centering function will
not work.
C Press the [Edit Image] key.
Note
❒ The original sizes and directions
for centering are listed below.
❖
Metric version
Original Original size and direction
placed on:
D Press the [Centering] key.
Exposure A3L, B4L, A4KL,
B5KL, A5L, 81/2" × 14"L,
glass
81/2" × 13"L
Document A3L, B4L, A4KL,
B5KL, A5KL, 81/2" ×
13"L
feeder
E Press the [OK] key.
F Press the [OK] key.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
G Place your originals, and then C Press the [Positive/Negative] key.
press the {Start} key.
Positive/Negative
If your original is black and white,
copy images are inverted.
2
D Press the [OK] key.
E Press the [OK] key.
R R
F Select the paper.
G Place your originals, and then
press the {Start} key.
GCHATN1E
A Press the [Edit/Stamp] key.
B Press the [Edit Image] key.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Erase
Erase
This function erases the center
and/or all four sides of the original
image. This is useful for avoiding
shadows on the copy image caused
by bound originals, such as books.
❖
Metric version
Where Origi- Paper Size and Orien-
nal Is Set tation
Exposure glass A3L, B4L, A4KL,
B5KL, A5L, 81/2" ×
2
This function has the following three
types:
14"L, 81/2" × 13"L
Document
feeder
A3L, B4L, A4KL,
B5KL, A5KL, 81/2"
× 13"L
❖
❖
❖
Border
This mode erases the edge margin
of the original image.
❖
Inch version
Center
Where Origi- Paper Size and Orien-
nal Is Set
This mode erases the center mar-
gin of the original image.
tation
11"
81/2"
14"
×
17"L,81/2"
×
×
14"
×
L
,
Exposure glass
Center/Border
×
11"KL, 10"
This mode erases both the center
and edge margins of the original
image.
L
, 8" 10"L
×
11"
81/2"
×
17"L,81/2"
14"L,
×
Document
feeder
×
11"KL, 10"
Note
14"L, 51/2" 81/2"L
×
❒ You can change the width of the
❒ The relationship between the orig-
inal orientation and the erased part
is as follows:
erased margins as follows:
Metric 2 – 99mm (in 1mm steps)
version
L original
K original
Inch
0.1" – 3.9" (in 0.1" steps)
version
❒
The default setting of the erased mar-
gin is as follows. You can change this
settings with the User Tools.
⇒
"Erase Border Width" and "Erase
2
1
Center Width" on p.194 “Edit 1/2”
1
Metric 10mm
version
1: Erased part
Inch
0.4"
2: 2–99mm
version
❒ The width of the erased margin
varies depending on the reproduc-
tion ratio.
❒ If the size of the original is differ-
ent from sizes listed in the follow-
ing chart, the erased margin might
be shifted.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
C Press the [Border] key.
Border Erase
This function erases the edge mar-
gins. You can set the same margin
width for all four sides, or you can set
different margin widths for each side.
2
D Set the erase border width.
Selecting [Same Width
]
A Press the [Same Width] key.
Note
❒ If you want to erase the center mar-
gin too, use the Center/Border
function. ⇒ p.122 “Center/Border
Erase”
A Press the [Edit/Stamp] key.
B Set an erase border width with
the [n] and [o] keys.
Note
❒ To change the value entered,
press the [n] and [o] keys
to set the new value.
C Press the [OK] key.
B Press the [Erase] key.
Selecting [Diff. Width
]
A Press the [Diff. Width] key.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Erase
B Press the key for the border
you wish to change and set an
erase border width with the
[n] and [o] keys.
B Press the [Erase] key.
Note
❒ To change the value entered,
press the [n] and [o] keys
to set the new value.
2
C Press the [OK] key.
E Press the [OK] key.
C Press the [Center] key.
F Place your originals, and then
press the {Start} key.
Center Erase
This function erases the center mar-
gin.
D Set the erase center width with
the [n] and [o] keys, and then
press the [OK] key.
Note
❒ If you want to erase the border
margin too, use the Center/Border
function. ⇒ p.122 “Center/Border
Erase”
Note
❒ To change the value entered,
press the [n] and [o] keys to
set the new value.
A Press the [Edit/Stamp] key.
E Press the [OK] key.
F Place your originals, and then
press the {Start} key.
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
C Press the [Center/Border] key.
Center/Border Erase
This mode erases both the center and
edge margins. You can set the same
margin width for all four sides and
center, or you can set different margin
widths for each.
2
D Set the erase margin width.
Selecting [Same Width
]
A Press the [Same Width] key.
B Press the [Center] key, and then
set the erase center width with
the [n] and [o] keys.
A Press the [Edit/Stamp] key.
Note
B Press the [Erase] key.
❒ To change the value entered,
press the [n] and [o] keys
to set the new value.
C Press the [Border] key, and then
set the erase border width with
the [n] and [o] keys.
Note
❒ To change the value entered,
press the [n] and [o] keys
to set the new value.
D Press the [OK] key.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Erase
Selecting [Diff. Width
]
A Press the [Diff. Width] key.
2
B Press the key for the part you
wish to change, and then set an
erase margin width with the
[n] and [o] keys.
Note
❒ To change the value entered,
press the [n] and [o] keys
to set the new value.
C Press the [OK] key.
E Press the [OK] key.
F Place your originals, and then
press the {Start} key.
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Margin Adjustment
You can shift the image to the left,
right, top or bottom to make a bind-
ing margin.
❒ When making two-sided copies
from one-sided originals, you can
set a binding margin for the back
side pages. ⇒ "1 sided → 2 sided
Auto Margin: T to T", "1 sided → 2
sided Auto Margin: T to B" on
p.194 “Edit 1/2”
2
A
A
❒ When making copies in Combine
mode, the binding margins are
made on the copies after the com-
bining is finished.
❒ When "2 Sided → 1 Sided" is select-
ed, set the binding margins for
front and back pages of the origi-
nal.
Limitation
❒ If you set the margin too wide, ar-
eas you do not want to delete
might be erased.
A Press the [Edit/Stamp] key.
Note
❒ You can change the width of the
binding margin as follows.
Metric 0 – 30mm (in 1mm steps)
version
Inch
0" – 1.2" (in 0.1" steps)
version
❒ The margin width default is as fol-
lows. You can change this default
setting with the User Tools. ⇒
"Front Margin: Left/Right", "Back
Margin: Left/Right", "Front Mar-
gin: Top/Bottom", "Back Margin:
Top/Bottom" on p.194 “Edit 1/2”
B Press the [Margin Adjustment] key.
Metric
version
•
•
Front: 5mm Left
Back: 5mm Right
Inch
version
•
•
Front: 0.2" Left
Back: 0.2" Right
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Margin Adjustment
C Set a binding margin for a front
page. Press the [←] and [→] keys
when setting the left and right
margins, and the [↓] and [↑] keys
when setting the top and bottom
margins.
2
Note
❒ To change the value entered,
press the [←], [→], [↓], [↑] keys
to set the new value.
❒ If you do not need to specify the
margins for the back side pages,
press the [OK] key and go to step
.
E
D Set a binding margin for the back
side pages. Press the [←] and [→]
keys when setting the left and
right margins, and the [↓] and [↑]
keys when setting the top and
bottom margins.
Note
❒ You can specify the margins for
the back side pages only when
Duplex or the Two Sided copy
with Combine is selected.
E Press the [OK] key.
F Place your originals, and then
press the {Start} key.
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Stamp
This function prints stamps on copies.
Stamp modes are as follows:
Note
❒ You can change the size of the
numbers with the User Tools. ⇒
"Size" on p.199 “Background
Numbering”
❖
❖
❖
❖
❖
Background Numbering
This function prints numbers on
the background of copies.
2
❒ You can change the density of the
numbers with the User Tools. ⇒
"Density" on p.199 “Background
Numbering”
Preset Stamp
This function prints preset messag-
es on copies.
❒ The numbers appear to overlap the
User Stamp
This function prints custom mes-
sages on copies.
copied image in some cases.
A Press the [Edit/Stamp] key.
Date Stamp
This function prints the date on
copies.
Page Numbering
This function prints page numbers
on copies.
Background Numbering
B Press the [Stamp] key.
The optional HDD and 32 MB of
memory are required to use this func-
tion (if the machine is equipped with
the Printer unit, 32MB of memory is
not required).
Use this function to have numbers
printed on the background of copies.
This function can help you to keep
track of confidential documents.
C Press the [Background Numbering
]
key.
GCSTMP2E
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
D Enter the number to start count-
ing from with the number keys,
and then press the [OK] key.
Preset Stamp
The optional 32 MB of memory is re-
quired to use this function (if the ma-
chine is equipped with the Printer
unit, 32 MB of memory is not re-
quired). There are also some other
settings available, by installing the
optional HDD.
2
Note
❒ The number can be set from 1 to
999.
❒ To change the entered number,
press the [Clear] or {Clear/Stop}
key and enter the new number.
E Press the [OK] key.
Limitation
❒ You cannot use the bypass tray
with this function.
❒ Only one message can be stamped
at a time.
Note
❒ One of the following eight messages
can be stamped on copies with a
frame around it: "COPY", "UR-
GENT", "PRIORITY", "For Your In-
fo.", "Preliminary", "For internal
use", "CONFIDENTIAL", "DRAFT".
F Press the [OK] key.
G Place your originals, and then
press the {Start} key.
❒ You can change the print page
with the User Tools.
❒ You can change the size and densi-
ty of the stamp with the User
Tools.
❒ Depending on the paper size, if
you change the stamp size, parts of
the stamp might not be printed.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ You can choose the default settings
for the language, position, size and
density of the stamp with the User
Tools. ⇒ "Stamp Language",
"Stamp Position", "Stamp Format"
on p.199 “Preset Stamp 1/4-4/4”
A Press the [Edit/Stamp] key.
❒ You can choose the default settings
for the print page with the User
Tools. ⇒ "Stamp Format" on p.199
“Preset Stamp 1/4-4/4”
2
❒ You can change the stamp lan-
guage with the User Tools. ⇒
"Stamp Language" on p.199 “Pre-
set Stamp 1/4-4/4”
B Press the [Stamp] key.
❒ The relationship between the di-
rection in which you place the
original and stamp orienta-
tion/position is as follows.
C Press the [Preset Stamp] key.
D Select the desired message.
GCSTMP5E
❒ You can move the stamp position
to the top, bottom, left and right in
1mm, 0.1" steps. ⇒ "Stamp posi-
1
tion" on p.199 “Preset Stamp /4-
4/4”
E Press the [All Pages] or [1st Page on-
ly] key to select the print page.
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
F Change the stamp position, size
User Stamp
or density.
If you do not wish to make a
The optional HDD and 32 MB of
memory are required to use this func-
tion (if the machine is equipped with
the Printer unit, 32 MB of memory is
not required).
change, go to step .
G
To change the stamp position,
size or density
2
Up to four messages which you use
frequently can be stored in the ma-
chine's memory and stamped on cop-
ies.
A Press the [Change] key.
B Select the desired position,
size and density.
C Press the [OK] key.
Preparation
Note
Before using this function, you
have to store your messages with
the User Tools. ⇒ p.131 “Pro-
gram/Delete User Stamp”
❒ To cancel the settings, press
the [Cancel] key.
G After you specify all the desired
settings, press the [OK] key.
Limitation
❒ You cannot use the bypass tray
with this function.
H Press the [OK] key.
❒ Only one message can be stamped
at a time.
Note
❒ You can change the print page
with the User Tools.
Note
❒ To cancel the settings, press the
[
Cancel] key.
I Place your originals, and then
press the {Start} key.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ The relationship between the di-
rection in which you place the
original and stamp orienta-
tion/position is as follows.
A Press the [Edit/Stamp] key.
2
B Press the [Stamp] key.
GCSTMP6E
C Press the [User Stamp] key.
❒ You can move the stamp position
to the top, bottom, left and right in
1mm, 0.1" steps. ⇒ "Stamp Posi-
1
tion" on p.200 “User Stamp /2-
2/2”
❒ You can choose the default settings
for the print page and the stamp
position with the User Tools. ⇒
"Stamp Format" and "Stamp Posi-
1
D Select the stamp you require.
tion" on p.200 “User Stamp /2-
2/2”
❒ You can combine this function
with only one Preset Stamp.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
E Press the [All Pages] or [1st Page on-
Program/Delete User Stamp
ly] key to select the print page.
A Make sure that the machine is in
To change the stamp position
Copy mode.
A Press the [Change] key.
B Press the {User Tools/Counter} key.
B Select the desired position.
2
C Press the [OK] key.
C Press the [Copier/Document Server
]
F After you specify all the desired
key.
settings, press the [OK] key.
Note
❒ To cancel the settings, press the
[
Cancel] key.
G Press the [OK] key.
D Press the [Stamp] key.
H Place your originals, and then
press the {Start} key.
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
C Enter the user stamp name with
the letter keys on the display
panel.
E Press the [User Stamp] key.
2
F Press the [Program/Delete Stamp
]
key.
Note
❒ You can register up to 10
characters.
Reference
For details on entering char-
acters, refer to "Entering Text
Characters" in the System
Settings manual.
D Press the [OK] key.
E Enter the horizontal size of the
To program the User Stamp
stamp with the number keys,
and then press the [#] key.
A Press the [Program] key.
B Press the stamp number (1 – 4)
Note
you want to program.
❒ You can enter sizes within the
horizontal range of 10 –
432mm, 1.0" – 17.0", and the
vertical range of 10 – 297mm,
1.0" – 11.7". However, if the
area exceeds the maximum
value (5,000mm2, 7.75 inch2),
it is corrected to within the ac-
ceptable range automatically.
Note
❒ Stamp numbers with m al-
ready have settings in them.
❒ If the stamp number is al-
ready being used, the ma-
chine will ask you if you
wish to overwrite it — Press
the [Yes] or [No] key.
❒ To change the value entered,
press the [Clear] or {Clear/Stop}
key and enter the new value.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
F Press the [Vertical] key, and
then enter the vertical size in
the same way as step E.
C Press the [Delete] key.
G Place the user stamp on the ex-
posure glass, and then press
the [Start Scanning] key.
Note
2
❒ Originals cannot be scanned
from the document feeder
when programming the user
stamp.
Note
❒ To cancel the deletion, press
❒ If you press the [Exit] key, the
the [Stop] key.
main
menu
of
the
D Press the [Exit] key.
Copy/Document Server fea-
tures appears with nothing
programmed.
E Press the [Exit] key.
G Press the [Exit] key.
H Press the [Exit] key.
The initial display appears.
To delete the User Stamp
Date Stamp
Important
❒ You cannot restore a deleted
stamp.
A Press the [Delete] key.
Limitation
❒ You cannot use the bypass tray
with this function.
B Press the stamp number (1 – 4)
you want to delete.
Note
Note
❒ Only programs with m con-
❒ You can select the following styles:
tain a user stamp.
• MM/DD/YYYY
• MM.DD.YYYY
• DD/MM/YYYY
• DD.MM.YYYY
• YYYY.MM.DD
• DD.JUN.YYYY
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ You can change the Date Stamp
settings with the User Tools. ⇒
p.201 “Date Stamp”
❒ If you combine this function with
the Combine, Magazine or Booklet
function, the page is stamped as
follows.
❒ The font and size of the Date
Stamp can be changed with the
User Tools. ⇒ "Font" and "Size" on
p.201 “Date Stamp”
• Combined with the Combine
function
❒ You can select whether the Date
Stamp is printed negative if it
overlaps black parts of an image.
⇒ "Superimpose" on p.201 “Date
Stamp”
2
❒ For how to set the date, see "Set
Date" in the System Settings manu-
al.
• Combined with the Magazine
or Booklet function
❒ You can choose the default settings
for the stamp position with the
User Tools. ⇒ "Stamp Position" on
p.201 “Date Stamp”
❒ The relationship between the di-
rection in which you place the
original and the stamp position is
as follows.
A Press the [Edit/Stamp] key.
B Press the [Stamp] key.
GCSTMP7E
❒ You can move the stamp position
to the top, bottom, left and right in
1mm, 0.1" steps. ⇒ "Stamp Posi-
tion" on p.201 “Date Stamp”
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
C Press the [Date Stamp] key.
To change the stamp position
A Press the [Change] key.
2
D Press the [All Pages] or [1st Page on-
ly] key to select the print page.
B Select the desired position of
the Date Stamp.
To change the style of date
A Press the [Change Format] key.
C Press the [OK] key.
E After you specify all the desired
B Select the format of date.
settings, press the [OK] key.
Note
❒ To cancel the settings, press the
[
Cancel] key.
F Press the [OK] key.
C Press the [OK] key.
G Place your originals, and then
press the {Start} key.
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ You can choose the default settings
for the stamp position with the
User Tools. ⇒ "Stamp Position" on
p.202 “Page Numbering 1/2-2/2”
Page Numbering
Use this function to print page num-
bers on your copies.
❒ You can choose the default settings
for the stamp format with the User
Tools. ⇒ "Stamp Format" on p.202
“Page Numbering 1/2-2/2”
2
❒ The relationship between the di-
rection in which you place the
original and the Page Numbering
orientation/position is as follows.
There are six types of Page Number-
ing (n is the total number of pages in
your original):
• P1,P2,…Pn
• 1/n,2/n,...n/n
• -1-,-2-,...-n-
• P.1,P.2,...P.n
• 1, 2…n
• 1-1,1-2,..1-n
Limitation
❒ You cannot use the bypass tray
with this function.
GCSTMP8E
Note
❒ You can change the Page Number-
ing settings with the User Tools. ⇒
p.202 “Page Numbering 1/2-2/2”
❒ You can move the stamp position
to the top, bottom, left and right in
1mm, 0.1" steps. ⇒ "Stamp Posi-
tion" on p.202 “Page Numbering
1/2-2/2”
❒ The font and size of Page Number-
ing can be changed with the User
Tools. ⇒ "Font" and "Size" on p.202
“Page Numbering 1/2-2/2”
❒ You can select whether the Page
Numbering is printed in negative
if it overlaps black parts of an im-
age. ⇒ "Superimpose" on p.202
“Page Numbering 1/2-2/2”
136
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
❒ If you combine this function with
the Duplex (Top to Top) function
and select the "P1, P2" or "1/n,
2/n" style, the page numbers on
the back of the copy paper are
printed as follows.
❖
Page Numbering per original
• Combined with 1 Sided/2 Sid-
ed in the Combine function
2
• Combined with the Maga-
2
1
zine or Booklet function
GCSTMPBE
1: Front
2: Back
❒ If you combine this function with
the Duplex (Top to Top) function,
you can change the setting to
stamp on the back side in the same
position as the front side. ⇒ "Du-
plex Back Page Stamping Position"
❖
Page Numbering per copy
1
• Combined with 1 Sided/2 Sid-
on p.202 “Page Numbering /2-
2/2”
ed in the Combine function
❒ If you use this function with the
Combine, Magazine, or Booklet
function, the page is stamped as
follows. ⇒ "Page Numbering In
Combine" on p.202 “Page Num-
bering 1/2-2/2”
❒ If you use the "1-1, 1-2" style, you
can print page numbers on the slip
sheets in Designate or Chapters
mode. ⇒ "Stamp on Designated
Slip Sheet" on p.202 “Page Num-
bering 1/2-2/2”
A Press the [Edit/Stamp] key.
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
B Press the [Stamp] key.
G To change the first printing page
and start number, press the right
[Change] key.
Note
❒ The display differs depending
on the selected style.
❒ If you do not wish to make a
change, press the [OK] key,
place your originals, and then
press the {Start} key.
2
C Press the [Page Numbering] key.
H Specify the page and number.
If you selected (P1,P2…, -1-,-2-
…, P.1, P.2…, 1, 2…, )
A Press the [First Printing Page
]
key, and then enter the original
sheet number from which to
start numbering with the
number keys.
D Select the format.
Note
E To change the stamp position,
❒ To change the number en-
tered, press the [Clear] or
{Clear/Stop} key, and then en-
ter a new number.
press the left [Change] key.
If you do not wish to change the
stamp position, go to step .
G
F Select the stamp position, and
B Press the {#} key.
then press the [OK] key.
138
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
C Press the [Numbering from/to
]
If you selected (1/5,2/5…)
key, and then enter the number
from which to start numbering
with the number keys.
A Press the [First Printing Page
]
key, and then enter the original
sheet number from which to
start numbering with the
number keys.
2
D Press the {#} key.
E Press the [Last Number] key, and
then enter the page number at
which to stop numbering with
the number keys.
Note
❒ To change the number en-
tered, press the [Clear] or
{Clear/Stop} key, and then en-
ter a new number.
B Press the {#} key.
C Press the [Numbering from/to
]
key, and then enter the page
number from which to start
numbering with the number
keys.
Note
❒ If you wish to print onto the
last page, press the [to the
end] key, and then go to step
J.
F Press the {#} key.
D Press the {#} key.
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
E Press the [Last Number] key, and
If you selected (1-1, 1-2,…)
then enter the page number at
which to stop numbering with
the number keys.
A Press the [First Printing Page
]
key, and then enter the original
sheet number from which to
start numbering with the
number keys.
If you do not wish to change the
number, go to step G.
2
Note
❒ If you wish to print onto the
Note
last page, press [to the end
]
❒ To change the number en-
tered, press the [Clear] or
{Clear/Stop} key, and then en-
ter a new number.
key, and then go to step J.
F Press the {#} key.
G Press the [Total Pages] key, and
then enter the total number of
original pages with the
number keys.
B Press the {#} key.
C Press the [First Chapter No.] key,
and then enter the chapter
number from which to start
numbering with the number
keys.
H Press the {#} key.
I Press the [OK] key.
D Press the {#} key.
140
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
E Press the [Numbering from/to
]
key, and then enter the page
number from which to start
numbering with the number
keys.
2
F Press the {#} key.
G Press the [OK] key.
I Press the [OK] key.
Note
❒ To change the settings after
pressing the [OK] key, press the
[
Change] key, and then enter the
new value.
J Press the [OK] key.
Note
❒ To cancel the settings, press the
[
Cancel] key.
K Place your originals, and then
press the {Start} key.
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Cover/Slip Sheet
Using this function, you can add cov-
er sheets or designate certain pages to
be copied on slip sheets.
Front Cover
The first page of your originals is cop-
ied on specific paper sheet for covers,
or a cover sheet is inserted before the
first copy.
There are four types of this function:
2
❖
❖
❖
❖
Front Cover
The first page of your originals is
copied on a specific paper sheet for
covers.
❖
Copy
Blank
Note
Front/Back Cover
The first and last pages of your
originals are copied on specific pa-
per sheets for covers.
3
3
2
2
1
1
Paper Designate
Use this function to have certain
pages of your originals copied
onto slip sheets.
❖
Chapter
If you specify the first page of each
chapter with this function, those
pages will always appear on the
front of copies when using 1 sided
→ 2 sided mode.
3
3
2
2
1
1
Preparation
❒ You can specify whether to make a
copy on the cover sheet. If you se-
lect [Copy], the first page will be
copied on the cover sheet. If you
select [Blank], a cover sheet will just
be inserted before the first copy.
Before selecting this function, set
the tray for front cover paper and
slip sheet paper. ⇒ "Cover", "Slip
Sheet 1" and "Slip Sheet 2" in the
System Settings manual
The cover or slip sheets should be
the same in size and direction as
the copy paper.
❒ When choosing [Copy], select wheth-
er the front and back covers are cop-
ied single-sided ("1 Sided Only") or
double-sided ("Duplex Copy"). ⇒
"Cover" in the System Settings man-
ual
Limitation
❒ You cannot set the copy paper in
the bypass tray. Only set the cover
or slip sheets in the bypass tray.
Note
❒ If Blank mode is selected, the cover
will not be counted as a copy.
142
Download from Www.Somanuals.com. All Manuals Search And Download.
Cover/Slip Sheet
❒ In "Cover" of the User Tools (Sys-
tem Settings), if you selected
"Mode Selected" for the "Tray Dis-
play" setting, the machine refers to
the settings in "Cover" about
whether the front and back covers
are copied single-sided ("1 Sided
Only") or double-sided ("Duplex
Copy"). If you selected "Display
Always" for "Tray Display", the
machine refers to the settings in
"Special Paper Indication" about
whether the front and back covers
are copied single-sided ("1 Sided
Copy") or double-sided ("Duplex
Copy"). ⇒ "Special Paper Indica-
tion" and "Cover" in the System
Settings manual
C Select [Copy] or [Blank] for the cov-
er sheet.
2
D Select the paper tray containing
the non-cover sheet paper, and
then press the [OK] key.
❒ When you use this function with
Combine mode, you can specify
whether to combine the front cover
or not. ⇒ "Front Cover Copy in
Combine" on p.196 “Edit 2/2”
A Press the [Cover/Slip Sheet] key.
E Place your originals in the docu-
ment feeder, and then press the
{Start} key.
B Press the [Front Cover] key.
143
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
❒ In "Cover" of the User Tools (Sys-
tem Settings), if you selected
"Mode Selected" for the "Tray Dis-
play" setting, the machine refers to
the settings in "Cover" about
whether the front and back covers
are copied single-sided ("1 Sided
Only") or double-sided ("Duplex
Copy"). If you selected "Display
Always" for "Tray Display", the
machine refers to the settings in
"Special Paper Indication" about
whether the front and back covers
are copied single-sided ("1 Sided
Copy") or double-sided ("Duplex
Copy"). ⇒ "Special Paper Indica-
tion" and "Cover" in the System
Settings manual
Front/Back Covers
The first and last pages of your origi-
nals are copied on specific paper
sheets for covers.
❖
Copy
2
4
4
3
3
2
2
1
1
GCCOVE0E
❖
Blank
Note
A Press the [Cover/Slip Sheet] key.
3
3
2
2
1
1
❒ You can specify whether to make a
copy on a cover sheet. If you select
[
Copy], the first and last pages will
be copied on the cover sheets. If
you select [Blank], a cover sheet
will just be inserted before the first
copy and another sheet after the
last copy.
B Press the [Front/Back Cover] key.
❒ When choosing
[Copy], select
whether the front and back covers
are copied single-sided ("1 Sided
Only") or double-sided ("Duplex
Copy"). ⇒ "Cover" in the System
Settings manual
144
Download from Www.Somanuals.com. All Manuals Search And Download.
Cover/Slip Sheet
C Select [Copy] or [Blank] for the cov-
Designate
er sheets.
Use this function to have certain pag-
es of your original copied onto slip
sheets.
2
10
10
D Select the paper tray containing
the non-cover sheet paper, and
then press the [OK] key.
5
5
1
1
Preparation
Before using this function, set the
special paper tray for slip sheets.
⇒ "Slip Sheet 1", "Slip Sheet 2" in
the System Settings manual
Limitation
❒ You cannot use this function with
E Place your originals in the docu-
ment feeder, and then press the
{Start} key.
Slip Sheet mode.
Note
❒ You can specify up to 20 pages.
❒ When Combine mode ("1 Sided →
2 Sided") has been selected, the
page numbers you designate will
always be copied onto the front of
copies in the same way as Chapters
mode.
❒ This function can be combined
with the Chapter function.
❒ When you use this function with
the Combine mode, you can speci-
fy whether to combine the desig-
nate pages or not. ⇒ " Designate
Slip Sheet Copy in Combine" on
p.196 “Edit 2/2”
145
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Note
A Press the [Cover/Slip Sheet] key.
❒
To change the value entered,
press the
[
Clear
]
or {Clear/Stop}
key, and then enter the new value.
E Select the paper tray for slip sheets.
F To specify another page location,
2
repeat steps to .
C
E
Note
❒ To select chapters 11 to 20, press
the [T11 20] key.
B Press the [Desig./Chapter] key.
∼
G When you wish to finish specify-
ing page locations, press the [OK
]
key.
C Press the key to select the chapter
number.
This display shows example set-
tings.
Note
❒ To change the number entered,
enter the new number in the
same way as steps to .
C
G
H Select the paper tray containing
the non-slip sheet paper, and then
press the [OK] key.
D Enter the page location of the
original you want to copy onto a
slip sheet with the number keys,
and then press the {#} key.
I Place your originals, and then
press the {Start} key.
146
Download from Www.Somanuals.com. All Manuals Search And Download.
Cover/Slip Sheet
B Press the [Desig./Chapter] key.
Chapter
The page locations you specify with
this function will appear on the front
of copy sheets.
2
6
4
4
3
1
1
5
C Press the [Chapter] key.
2
GC SHOW OJ
Preparation
Before selecting this function,
press the [Dup./Combine/Series] key
and select Duplex (1 Sided → 2
Sided) mode or Combine mode.
D Enter the page location of the first
page of the first chapter with the
number keys, and then press the
Limitation
❒ You cannot use this function with
Slip Sheet mode.
{#} key.
Note
❒ You can specify up to 20 pages.
❒ This function can be used only
when you use the Duplex (1
Sided→2 Sided) or Combine func-
tion.
❒ This function can be combined
with the Designate function.
Note
A Press the [Cover/Slip Sheet] key.
❒ To change the value entered,
press the [Clear] or {Clear/Stop}
key, and then enter the new val-
ue.
E To specify another page location,
repeat steps to .
C
E
Note
❒ To select chapters 11 to 20, press
the [T11-20] key.
147
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
F When you finish specifying the
page locations, press the [OK] key.
2
This display shows example set-
tings.
Note
❒ To change the number entered,
enter the new number in the
same way as in steps to .
C
E
G Place your originals, and then
press the {Start} key.
148
Download from Www.Somanuals.com. All Manuals Search And Download.
Slip Sheets
Slip Sheets
Every time the originals' page chang-
es, a slip sheet is inserted. This func-
tion can be used to insert a slip sheet
automatically between each OHP
transparency copied or used as a
stack function. You can also copy
onto the inserted slip sheets.
When using OHP transparencies
set on the bypass tray
❖
Copy
2
2
2
2
2
1
1
1
1
2
1
2
3
3
❖
Blank
2
Preparation
1
1
Before selecting this function,
specify the paper tray for slip
sheets. ⇒ "Slip Sheet 1", "Slip Sheet
2" in the System Settings manual
Note
❒ Press the {#} key and set the "Spe-
cial Paper" setting to [OHP Sheet].
⇒ p.57 “When copying onto stand-
ard size paper”
Limitation
❒ You cannot use this function with
Chapters and Paper Designate
modes.
A Press the [Cover/Slip Sheet] key.
Note
❒ The trays to be used in the Slip
Sheets function are those pro-
grammed in "Slip Sheet 1" and
"Slip Sheet 2" in the System Set-
tings.
❒ Load the slip sheets in the same
orientation as the originals.
❒ You can specify whether to copy
onto the inserted slip sheets or not.
❒ If you do not copy onto slip sheets,
they are excluded from the
number of copies counted.
149
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
B Press the [Slip sheet] key.
2
C Select [Copy] or [Blank], and then
press the [OK] key.
D Select the paper tray containing
the non-slip sheet paper.
When using OHP transparencies,
open the bypass tray.
E Place your originals, and then
press the {Start} key.
150
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing Originals in the Document Server
Storing Originals in the Document Server
The optional HDD is required to use this function.
The Document Server enables you to
save documents in the machine mem-
For more information on the
ory and then print them as you want.
types of originals that can be
Reference
2
placed and how to place them,
⇒ p.31 “Placing Originals”.
Reference
Refer to the System Settings manu-
al.
D Make the scanning settings for
the original.
Note
❒ You can specify whether data
stored in the Document Server is
deleted automatically later. (''Auto
Delete File'' in System Settings
manual under ''Key Operator
Tools''). The stored data is set to be
deleted after one day by the facto-
ry default value. For information
about settings and changes, see the
System Settings manual.
Reference
For details, see the explanation
of each function in this manual.
A Press the [Stored File] key.
E Press the {Start} key.
Originals are scanned.
Note
❒ To stop scanning, press the
{Clear/Stop} key.
❒ To resume a paused scanning
job, press the [Resume] key in
the confirmation dialog box. To
delete the saved images and
B Enter a file name, user name, or
password if neccessary.
cancel the job, press the [Cancel
]
key.
❒ To check if the document has
been stored, press the {Docu-
ment Server} key to display the
document selection screen.
C Place your originals.
151
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
Combination Chart
The combination chart given below shows which modes can be used together.
When you read the chart, see the following table.
❍
means that these modes can be used together.
$
means that these modes cannot be used together. The second
mode selected will be the mode you're working in.
2
×
means that these modes cannot be used together. The first mode
selected will be the mode you're working in.
The following shows the combinations of functions.
152
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Troubleshooting
If Your Machine Does Not Operate as You
Want
General
Machine Status
Problem/Cause
Action
Please wait.
A message appears when
you turn on the operation
switch or change the toner
bottle.
Wait for the machine.
Cannot detect original size. Improper original is
Place a custom size original on the
placed. ⇒ p.20 “Sizes diffi- exposure glass. ⇒ p.31 “Placing
cult to detect”
Originals on the Exposure Glass”
Input the horizontal and vertical
size of the custom original. ⇒ p.31
“Placing Originals on the Exposure
Glass”
Select paper manually, not with
Auto Paper Select mode.
Do not use Auto Reduce/Enlarge
mode.
Original is not placed.
Place your originals.
Check original orientation. There is no copy paper that Place the original in the same direc-
is in the same direction as tion as the copy paper.
the originals.
Check paper size.
Improper paper size is set. If you press the {Start} key, copy
will start onto the selected paper.
Rotate Sort is not available A size of paper for which
with this image size.
Select the proper paper size. ⇒ p.47
Rotate Sort is not available “Sort”
is selected.
It is over stapling capacity. The number of sheets per
Check the stapler capacity. ⇒ p.51
set is over the staple capac- “Staple”
ity.
Cannot staple paper of this The Staple function cannot Select a paper size that can be used
size.
be used with paper size se- in Staple mode. ⇒ p.51 “Staple”
lected.
Duplex is not avilable with A paper size not available Select the proper paper size. ⇒ p.88
this paper size.
in Duplex mode has been
selected.
“Duplex”
Maximum number of sets The number of copies ex-
You can change the maximum copy
quantity. ⇒ “Max. Copy Quantity”
on p.187 “General Features 2/4”
is *.
ceeds the maximum copy
quantity.
153
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Document Server
Machine Status
Problem/Cause
Action
Scanned pages exceeded
The number of scanned
If you want to store the scanned
max. number. Do you want pages exceeds the capacity originals as a file, press the [Store
to store the scanned pages per file of the Document
as a file? Server.
File] key. The originals are stored as
a file in the Document Server. If you
don't want any scanned originals to
be stored, press the [No] key. The
scanning data will be cleared.
Magazine or Booklet mode You selected Magazine or
Make sure that the documents for
3
is not available due to
mixed image mode.
Booklet mode for documents Magazine or Booklet mode are
scanned from different func-
tions, such as copy and printer.
scanned from the same function.
Document Server
Problem
Action
You forgot your password.
You can confirm your password.
Press the [Yes] key temporarily for "Display
Password with Stored file" in system settings.
You can check the password when you select-
ed the file. ⇒ "Display Password with Stored
file" in system settings
Without the password, you cannot edit or
print the document. Scan the document again.
You can delete all the saved documents at
once with the User Tools. ⇒ "Delete All The
Saved Files" on p.204 “Input/Output”
Make sure that no important document is
saved in the Document Server before deleting
all of the saved documents.
You cannot find out what is saved in a file.
Check the date or time column in the "Docu-
ment Server: Files" display.
Check the contents of the document by print-
ing the first page of it. Press the line for the de-
sired document in the "Document Server:
Files" display, and press the [Print 1st Page] key
followed by the {Start} key.
Memory becomes full frequently.
Select the document that you want to delete,
and then press the [Delete File] key.
You want to check the print result before mak- Check the print result by printing out only the
ing a large print run. first set.
You want to save a document which cannot be Turn "Auto File Delete" off, and then save the
deleted automatically.
document in the Document Server.
If you later turn on "Auto File Delete", the
function is only applied to the documents that
were saved after turning the function on.
154
Download from Www.Somanuals.com. All Manuals Search And Download.
If Your Machine Does Not Operate as You Want
Display
Problem
Problem/Cause
Action
The display panel is off.
The screen contrast knob is
turned to the dark position.
Set the screen contrast knob to
the light position for proper
viewing of the display panel.
The machine is in Energy Sav- Press the {Energy Saver} key to
er mode.
cancel Energy Saver mode.
The operation switch is
turned off.
Turn on the operation switch.
3
Nothing happens when the
The main power switch is
operation switch is turned on. turned off.
Turn on the main power
switch.
155
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If You Cannot Make Clear Copies
Problem
Cause
Action
Copies appear dirty.
The image density is too
dark.
Adjust the image density. ⇒ p.38
“Adjusting Copy Image Density”
Auto Image Density is not Select Auto Image Density. ⇒ p.38
selected.
“Adjusting Copy Image Density”
The reverse side of an orig- The image density is too
inal image is copied. dark.
Adjust the image density. ⇒ p.38
“Adjusting Copy Image Density”
3
Auto Image Density is not Select Auto Image Density. ⇒ p.38
selected.
“Adjusting Copy Image Density”
A shadow appears on cop- The image density is too
ies if you use pasted origi- dark.
nals.
Adjust the image density. ⇒ p.38
“Adjusting Copy Image Density”
Change the direction of the original.
Put mending tape on the pasted
part.
The same copy area is dirty The exposure glass or doc- Clean them. ⇒ p.210 “Maintaining
whenever making copies.
ument feeder is dirty.
Your Machine”
Copies are too light.
The image density is too
light.
Adjust the image density. ⇒ p.38
“Adjusting Copy Image Density”
The paper size is not ap-
propriate.
Use the recommended paper.
Note
❒ A light copy may result when
you use damp or rough grain pa-
per.
Toner cartridge is almost
empty.
Add toner. ⇒ p.162 “D Adding
Toner”
Parts of the image are not
copied.
The original is not set cor- Set originals correctly. ⇒ p.31 “Plac-
rectly. ing Originals”
An improper paper size is Select the proper paper size.
selected.
Copies are blank.
The original is not set cor- When using the exposure glass, face
rectly.
the originals down. When using the
document feeder, face them up. ⇒
p.31 “Placing Originals”
A moiré pattern is pro-
duced on copies.
Your original has a dot pat- Place the original on the exposure
tern image or many lines. glass at a slight angle.
R
156
Download from Www.Somanuals.com. All Manuals Search And Download.
If You Cannot Make Copies As You Want
If You Cannot Make Copies As You Want
General
Problem
Cause
Action
Copies are not stapled.
There are jammed staples
in the stapler.
Remove jammed staples. ⇒ p.175
“e Removing Jammed Staples”
Note
❒ After removing jammed staples,
staples might not be ejected the
first few times you try to use the
stapler.
3
Thenumber ofcopies exceeds Check the stapler capacity. ⇒ p.51
the capacity of the stapler.
“Staple”
Copy paper is curled.
Turn the copy paper over in the
tray.
Staples are wrongly posi-
tioned.
Originals are not set cor-
rectly.
Check the correct position to place
the originals. ⇒ p.51 “Staple”
Misfeeds occur frequently. Copy paper size setting is Set the proper paper size. ⇒ p.170
not correct.
“Changing the Paper Size”
You cannot combine sever- Selected functions cannot
⇒ p.152 “Combination Chart”
al functions.
be used together.
When sorting, the pages
are divided into two
blocks.
The memory became full in You can interrupt copying when the
the middle of sorting and memory becomes full. ⇒ "Memory
the pages were delivered in Full Auto Scan Restart" on p.204
two blocks.
“Input/Output”
Adjust Image
Problem
Cause
Action
In Double Copies mode, parts Combination of original and
Select A3L for A4 K origi-
nals and A4 for A5 originals.
⇒ p.116 “Double Copies”
of the original image are not
copied.
copy paper is not correct.
In Border, Center, or Cent-
er/Border mode, parts of the
original image are not copied.
You set a wide erased margin. Make the margin width nar-
rower. You can adjust it be-
Originals are not scanned cor-
tween 2-99mm. ⇒ "Erase
rectly.
Border Width" and "Erase Cent-
er Width" on p.194 “Edit 1/2”
Set the originals correctly.
In Margin Adjustment mode, You set a wide erased margin. Set a narrower margin with
parts of the original image are
not copied.
the User Tools. ⇒ "Front Mar-
gin: Left/Right" and "Back
Margin: Left/Right" on p.194
“Edit 1/2”
There is a lack of margin space
on the opposite side of the
binding position.
157
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Cause
Action
In Image Repeat mode, the
original image is not copied
repeatedly.
You selected copy paper the
same size as the originals, or
you did not select the proper
reproduction ratio.
Select copy paper larger than
the originals.
Select the proper reproduc-
tion ratio.
Stamp
Problem
Cause
Action
The stamp position is wrong. The paper orientation is
wrong.
Check the paper orientation
and stamp position.
3
Combine
Problem
Cause
Action
You cannot make a book from Combine Original Booklet
a booklet or magazine by fold- Format or Combine Original
Change the setting. ⇒ p.91
“Combine”
ing copies.
Magazine Format is not cor-
rect.
Parts of the image are not cop- You specified a reproduction When you specify a reproduc-
ied. ratio that does not match the tion ratio using Manual Paper
sizes of your originals and
copy paper.
Select mode, make sure that
the ratio matches your origi-
nals and the copy paper.
Note
❒ Select the correct repro-
duction ratio before using
Combine mode.
Order of copies is not correct. You placed the originals in the When placing a stack of origi-
incorrect order.
nals in the document feeder,
the last page should be on the
bottom.
If you place an original on the
exposure glass, start with the
first page to be copied.
158
Download from Www.Somanuals.com. All Manuals Search And Download.
If You Cannot Make Copies As You Want
Duplex
Problem
Cause
Action
Order of copies is not correct. You place the originals in the When placing a stack of origi-
incorrect order.
nals in the document feeder,
the last page should be on the
bottom.
If you place an original on the
exposure glass, start with the
first page to be copied.
3
Orientation of copies (Top to You placed the originals in the Set originals in the 90° Turn
Top, or Top to Bottom) is not wrong direction or the orien- orientation. ⇒ p.33 “Original
correct.
tation setting is incorrect.
Orientation”
When Memory Is Full
Note
❒ If you set "Memory Full Auto Scan Restart"of the User Tools (⇒ p.204) to
"Yes", the memory overflow message will not be displayed, but make Con-
nect Copy for the scanned originals automatically. Connect Copy continues
scanning and copying until finishing the job. Note that copy sets will be print-
ed out separately by scanning at this time.
Machine Status
Action
Memory is full.
Press the [Output] key to copy scanned origi-
nals and clear the scanning data. Press the
[Clear] key to clear the scanning data without
making copies.
Press the [Resume] key to scan and copy re-
maining originals.
To continue copying, remove all copies, and
then press the [Resume] key. To stop copying,
press the [Stop] key.
Document Server
Machine Status
Action
Memory is full.
Delete any unnecessary files, and then scan
the document again.
159
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
B Loading Paper
Setting special paper in the
Paper Tray 2
Loading Paper in Tray 1-4
Note
A Set the special paper below the
❒ You can change the paper size. ⇒
p.170 “Changing the Paper Size”
limit mark of the tray.
Reference
3
Regarding paper types and sizes,
⇒ p.22 “Copy Paper”.
A Pull out the paper tray until it
stops.
B Square the paper and load it in
the tray with the copying face up.
Note
❒ Shuffle the paper before
loading it in the tray.
❒ When copying onto paper
such as translucent paper,
straighten curled or warped
paper before placing it in the
tray.
C Push the paper tray in until it
Important
stops.
❒ If you add paper to a paper tray
where paper is still left, a mis-
feed might occur.
❒ Do not stack paper over the lim-
it mark.
❒ When setting small quantities of
copy paper, be careful not to
squeeze in the side fence too
much or paper will not be fed
properly.
160
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Loading Paper
Note
Loading Paper in the Large
Capacity Tray
❒ Shuffle the paper before loading
it in the tray.
❒ Straighten curled or warped pa-
Note
per before placing it in the tray.
❒ Load copy paper of the same size
and direction in both left and right
side trays.
C Push the paper tray in until it
stops.
A Pull out the large capacity tray.
3
B Square the paper and load it in
the tray with the copying face up.
Important
❒ Align the right edge of the right
copy paper stack with the right
edge of the tray.
❒ Align the left edge of the left
copy paper stack with the left
edge of the tray.
❒ Do not stack paper over the lim-
it mark.
161
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
D Adding Toner
When D is displayed, it is time to add toner.
R WARNING:
• Do not incinerate used toner or toner containers. Toner dust might ig-
nite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations for plastics.
R CAUTION:
• Keep toner (used or unused) and toner containers out of reach of children.
3
R CAUTION:
• Our products are engineered to meet high standards of quality and function-
ality, and we recommend that you only use the expendable supplies availa-
ble at an authorized dealer.
Important
❒ If you use toner other than that recommended, an error might occur.
❒ When adding toner, do not turn off the operation switch. If you do, your set-
tings will be cleared and D will appear again because the machine will not
recognize that toner has been added.
❒ Always add toner after the machine instructs you to add toner.
❒ Do not use used toner. This will damage the machine.
Note
❒ You can still make about 50 copies after D appears, but replace the toner ear-
ly to prevent poor copy quality.
Reference
Regarding toner storage, ⇒ p.27 “Toner Storage”.
•
•
1: Open the front cover of the machine.
2: Lift the green lever.
•
3: Push the green lever, and then gently
pull out the holder.
162
Download from Www.Somanuals.com. All Manuals Search And Download.
D
Adding Toner
•
•
4: Push the toner bottle backward to raise
its head, and then gently pull out the bot-
tle.
5: Hold a new bottle horizontally and
shake it 5 or 6 times.
5 6
Note
3
❒ Do not remove the black cap before
shaking.
•
•
6: Remove the black cap.
Note
❒ Do not remove the inner cap.
7: Put the toner bottle on the holder, and
then push its head forward.
•
•
•
8: Push the holder until it clicks.
9: Push down the green lever.
10: Close the front cover of the machine.
163
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
x Clearing Misfeeds
R CAUTION:
• The fusing section of this equipment might be very hot. You should be very
careful that you don't touch this section when removing the misfed paper.
Important
❒ When clearing misfeeds, do not turn off the operation switch. If you do, your
copy settings are cleared.
❒ To prevent misfeeds, do not leave any torn scraps of paper within the ma-
3
chine.
❒ If paper misfeeds occur repeatedly, contact your service representative.
Note
❒ More than one misfed area may be indicated. In this case, check every appli-
cable area. See the following charts: A, B, C, D, P, R, Y, Z
❒ You can find a sticker explaining how to remove misfed paper inside the front
cover or inside the finisher.
164
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Clearing Misfeeds
3
165
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
3
166
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Clearing Misfeeds
3
167
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
3
168
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Clearing Misfeeds
3
169
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Changing the Paper Size
Preparation
Changing the Paper Size in
The procedures for changing the
paper size are different depending
on the tray (paper tray 1, paper
tray 2 or the optional paper tray
units). Check that you are follow-
ing the appropriate procedure be-
fore you start.
Tray 1-4/Paper Tray Unit
A Make sure that the paper tray is
not being used, and then fully
pull out the tray.
3
Note
Reference
⇒ p.57 “Copying from the Paper
Tray 2”
❒ Make sure that there is no paper
left in the paper tray.
B While pressing the release lever,
Important
adjust the back fence.
❒ If you wish to change the paper
size set in the optional large capac-
ity tray (LCT), contact your service
representative.
❒ Be sure to select the paper size
with the user tools. Otherwise,
misfeeds might occur. Refer to the
System Settings manual.
Reference
For paper sizes, types, and weights
that can be set in each tray, and the
capacity of each tray ⇒ p.22 “Copy
Paper”.
C Release the side lever.
170
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Paper Size
D While pressing the release lever, G Lock the side lever.
adjust the side fences.
3
H While pressing the release lever,
adjust the back fence to the new
paper size.
E Square the paper and load it in
the tray with the copying face up.
Important
❒ Do not stack paper over the lim-
it mark.
I Adjust the paper size selector to
the new paper size.
F While pressing the release lever,
adjust the side fences to the new
paper size.
Note
❒ To adjust the paper size to those
not available in the paper size
selector, set the paper size selec-
tor to the p mark and select the
paper size in the User Tools
(System Settings).
Important
❒
When loading small quantities of
copy paper, be careful not to
squeeze in the side fence too much
or paper will not be fed properly.
J Push the paper tray in until it
stops.
171
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
d Adding Staples
R CAUTION:
• Our products are engineered to meet high standards of quality and function-
ality, and we recommend that you only use the expendable supplies availa-
ble at an authorized dealer.
Important
❒ If you use a staple cartridge other than that recommended, staple failure or
staple jams might occur.
3
Reference
For the type of finisher, refer to “Options” ⇒ p.7
500-Sheet Finisher
•
•
•
•
1: Open the side cover.
2: Remove the cartridge.
3: Take out the empty refill in the direction
of the arrow.
4: Push in the new refill until it clicks.
172
Download from Www.Somanuals.com. All Manuals Search And Download.
d
Adding Staples
•
5: Pull out the ribbon.
•
•
6: Reinstall the cartridge.
7: Close the side cover.
3
1000-Sheet Finisher
•
1: Open the front cover of the finisher and
pull out the staple unit.
•
2: Hold the green lever and pull out the
cartridge gently.
•
•
3: Hold the both sides of the cartridge.
4: Pull up the upper unit of the cartridge.
PUSH
173
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
•
5: Take out the empty refill in the direction
of the arrow.
•
•
•
6: Align the arrows on the new refill and
the cartridge, and then push in the refill
until it clicks.
3
7: Push down the upper unit into the car-
tridge gently.
8: Pull out the ribbon.
•
•
9: Hold the green lever and reinstall the
cartridge until it clicks.
10: Push back the staple unit and close the
front cover of the finisher.
174
Download from Www.Somanuals.com. All Manuals Search And Download.
e
Removing Jammed Staples
e Removing Jammed Staples
Note
❒ Staples might jam because of curled copy paper. In this case, try turning the
copy paper over in the tray. If there is no improvement, change to copy pa-
pers with less curl.
❒ When 500-Sheet Finisher is installed, after removing jammed staples, staples
might not be ejected the first few times you try to use the stapler.
Reference
3
For the type of finisher, refer to “Options” ⇒ p.7
500-Sheet Finisher
•
•
•
•
1: Open the side cover.
2: Remove the cartridge.
3: Open the face plate.
4: Remove the jammed staples.
175
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
•
•
5: Reinstall the cartridge.
6: Close the side cover.
1000-Sheet Finisher
3
•
1: Open the front cover of the finisher and
pull out the staple unit.
•
•
•
2: Hold the green lever and pull out the
cartridge gently.
3: Open the face plate of the cartridge.
4: Remove the jammed staples.
176
Download from Www.Somanuals.com. All Manuals Search And Download.
e
Removing Jammed Staples
•
5: Pull down the face plate of the cartridge
until it clicks.
•
•
6: Hold the green lever and reinstall the
cartridge until it clicks.
7: Push back the staple unit and close the
front cover of the finisher.
3
177
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
3
178
Download from Www.Somanuals.com. All Manuals Search And Download.
4. User Tools (Copy/Document
Server Features)
Accessing the User Tools
(Copy/Document Server Features)
This section is for the key operators in
B Press the [Copier/Document Server
charge of this machine. You can
Features] key.
change or set the machine's default
The Copier/Document Server Fea-
tures menu appears.
settings.
Preparation
After using the User Tools, be sure
to exit from the User Tools.
The selected key is highlighted.
Any changes you make with the
User Tools remain in effect even if
the main power switch or opera-
tion switch is turned off, or the
{Clear Modes} key is pressed.
C Select the desired menu, and then
Reference
press the desired key.
For details, ⇒ "Accessing the User
Tools (System Settings)" in the Sys-
tem Settings manual.
A Press the {User Tools/Counter} key.
The User Tools Main Menu ap-
pears.
Note
❒ [TNext]: Press to go to the next
page.
❒ [UPrevious]: Press to go back to
the previous page.
Reference
⇒ p.182 “User Tools Menu
(Copier/Document Server Fea-
tures)”
179
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
D Change the settings by following
the instructions on the display
panel, and then press the [OK
]
key.
Reference
⇒ p.190 “General Features 4/4”
Note
❒ [OK]: Press to set the new set-
tings and return to the previous
menu
❒ [Cancel]: Press to return to the
previous menu without chang-
ing any data
4
Exiting From the User Tools
A After changing the User Tools set-
tings, press the [Exit] key on the
User Tools Main Menu.
Changing the User Tools is com-
pleted, and the machine is ready
for copying.
Note
❒ You can also exit from the User
Tools by pressing the {User
Tools/Counter} key.
180
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing the User Tools (Copy/Document Server Features)
4
181
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
User Tools Menu (Copier/Document
Server Features)
4
182
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools Menu (Copier/Document Server Features)
4
183
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
General Features 1/4
❖
Auto Paper Select Priority
As a default setting, Auto Paper Select is selected. You can cancel this setting.
Note
❒ Default: On
❖
Auto Tray Switching
If you load paper of the same size in two or more trays, the machine automat-
ically shifts to the other tray when the first tray in use runs out of paper (when
Auto Paper Select is selected.) This function is called "Auto Tray Switching".
This setting specifies whether to use "Auto Tray Switching" or not.
Default: With image rotation
4
Note
❒ [With image rotation] Use this to copy with Auto Tray Switching.
❒ [Without image rotation] Only copies with Auto Tray Switching if you load
paper of the same size and in the same direction in two or more trays. If the
paper is not the same size or in the same direction, copying is interrupted
and the message "Load paper." is displayed.
❒ [OFF] When a paper tray runs out of paper, copying is interrupted and the
message "Load paper." is displayed.
❖
Paper Display
You can choose whether the available paper trays/sizes are shown on the in-
itial display.
Note
❒ Default: Display
❒ If you choose "Hide", the display is shown as below. When the [Auto Paper
Select] key is pressed, paper sizes appear on the display.
❖
Original Type Priority
As a default setting, Text is selected as the Original Type. You can change it
to Text/Photo, Photo, Pale, or Generation Copy.
Note
❒ Default: Text
184
Download from Www.Somanuals.com. All Manuals Search And Download.
General Features 1/4
❖
Original Type Display
You can choose whether the original types are shown on the initial display.
Note
❒ Default: Display
❒ If you choose "Hide", the display is shown as below.
4
❖
❖
Auto Image Density Priority
You can turn the Auto Image Density on or off for each of the original types
(Text, Text/Photo, Photo, Pale, and Generation Copy).
Note
❒ Default: Text: On, Text/Photo: On, Photo: Off, Pale: On, Generation Copy: On
Copy Quality
You can adjust the quality level of copies for each of the original types (Text,
Text/Photo, Photo, Pale, Generation Copy).
• Text
Adjust the sharpness of text.
Note
❒ Default: Normal
❒ [Custom Setting] is a value set by the service representative.
❒ Choosing [Sharp] or [Sort] affects the outline sharpness of text.
185
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
• Text/Photo
When there are photo(s) and text on the original, determine whether the
photo or text takes priority.
Note
❒ Default: Normal
❒ [Custom Setting] is a value set by the service representative.
❒ [Normal] achieves a good balance between text and photos.
• Photo
For a photo original, adjust the quality level to match the type of photo
original.
Note
❒ Default: Print Photo
4
❒ [Custom Setting] is a value set by the service representative.
❒ Select [Print Photo] for printed photo originals, and [Coarse Print] for a
coarse dot finish such as newspaper photos.
❒ Select [Glossy Photo] for printed photo and text originals.
• Pale
Adjust the quality level for a pale original with normal density.
Note
❒ Default: Normal
❒ [Custom Setting] is a value set by the service representative.
• Generation Copy
Adjust the quality level so as not to thicken the lines of the image.
Note
❒ Default: Normal
❒ [Custom Setting] is a value set by the service representative.
❖
Image Density
You can select one of seven original image density levels for each of the orig-
inal types (Text, Text/Photo, Photo, Pale, Generation Copy).
Note
❒ Default: Text: Normal, Text/Photo: Normal, Photo: Normal, Pale: Normal, Gen-
eration Copy: Normal
186
Download from Www.Somanuals.com. All Manuals Search And Download.
General Features 2/4
General Features 2/4
❖
Duplex Mode Priority
You can select the type of Duplex function effective when the machine is
turned on, reset, or modes are cleared.
Note
❒ Default:
• Metric version: 1 Sided→1 Sided
• Inch version: 1 Sided→2 Sided
❖
❖
❖
Copy Orientation in Duplex Mode
You can set the copy orientation when making two-sided copies.
4
Note
❒ Default: Top to Top
Original Orientation in Duplex Mode
You can set the original orientation when making two-sided copies.
Note
❒ Default: Top to Top
Change Initial Mode
You can select the initial mode or Program No. 10 as the mode effective when
the machine is turned on, reset, or modes are cleared.
Note
❒ Default: Standard
❖
❖
Max. Copy Quantity
The maximum copy quantity can be set between 1 and 99.
Note
❒ Default: 99Sheets.
Tone: Original remains
The beeper (key tone) sounds when you forgot to remove originals after cop-
ying.
Note
❒ Default: On
❒ If the "Panel Tone" of the User Tools (System Settings) setting is "Off", the
beeper does not sound irrespective of the "Tone: Original remains" setting.
⇒"Panel Tone" in the System Settings manual
187
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
❖
Job End Call
You can choose whether or not the beeper sounds when copying is complete.
If the "Panel Tone" of the User Tools (System Settings) settings is "On", the
machine beeps to notify you that the machine did not complete a job for rea-
sons such as copying was interrupted, the paper tray ran out of paper or a pa-
per jam occurred.
Note
❒ Default: On
4
188
Download from Www.Somanuals.com. All Manuals Search And Download.
General Features 3/4
General Features 3/4
❖
Copy Function Key: F1-F5
You can register frequently used functions in function keys F1 to F5.
4
Note
❒ Default:
• Copy Function Key: F1: 1 Sided→2 Sided:T to T
• Copy Function Key: F2: 2 Sided:T to T→2 Sided:T to T
• Copy Function Key: F3: 1 Sided→1 Sided Combine:2 Originals
• Copy Function Key: F4: 1 Sided→1 Sided Combine:4 Originals
• Copy Function Key: F5: Create Margin
189
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
General Features 4/4
❖
Document Server Storage Key: F1–F5
You can register frequently used functions in function keys F1 to F5. You can
also change the registered functions.
4
Note
❒ Default
• Document Server Storage Key: F1: 2 Sided Original Top to Top
• Document Server Storage Key: F2: 1 Sided → 1 Sided Combine: 2 originals
• Document Server Storage Key: F3: 1 Sided → 1 Sided Combine: 4 originals
• Document Server Storage Key: F4: 1 Sided → 1 Sided Combine: 8 originals
• Document Server Storage Key: F5: Create Margin
190
Download from Www.Somanuals.com. All Manuals Search And Download.
Reproduction Ratio 1/2
Reproduction Ratio 1/2
❖
Shortcut R/E
You can register up to three frequently used Reduce/Enlarge ratios other
than the fixed Reduce/Enlarge ratio and have them shown on the initial dis-
play. You can also change the registered Reduce/Enlarge ratios.
If no Reduce/Enlarge ratio has been set when selecting [Shortcut R/E 1], [Short-
cut R/E 2], or [Shortcut R/E 3], enter the desired Reduce/Enlarge ratio using the
number keys.
❖
Enlarge 1-5
You can customize the enlargement ratios available when you press the [Re-
duce/Enlarge] key followed by the [Enlarge] key.
4
Note
❒ Default:
• Metric version:
• Enlarge 1: 115%
• Enlarge 2: 122%
• Enlarge 3: 141%
• Enlarge 4: 200%
• Enlarge 5: 400%
• Inch version:
• Enlarge 1: 121%
• Enlarge 2: 129%
• Enlarge 3: 155%
• Enlarge 4: 200%
• Enlarge 5: 400%
❒ When selecting [User Enlrg. Ratio], enter a ratio using the number keys (in
the range of 101 to 400%).
❖
Priority Setting: Enlarge
You can set the ratio with priority when the [Reduce/Enlarge] key is pressed,
followed by the [Enlarge] key.
Note
❒ Default:
• Metric version: 141%
• Inch version: 155%
191
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
Reproduction Ratio 2/2
❖
Reduce 1-6
You can customize the reduction ratios available when you press the [Re-
duce/Enlarge] key followed by the [Reduce] key.
Note
❒ Default:
• Metric version:
• Reduce 1: 25%
• Reduce 2: 50%
• Reduce 3: 65%
• Reduce 4: 71%
• Reduce 5: 75%
• Reduce 6: 82%
• Inch version:
• Reduce 1: 25%
• Reduce 2: 50%
• Reduce 3: 65%
• Reduce 4: 73%
• Reduce 5: 78%
• Reduce 6: 85%
4
❒ When selecting [User Redc.Ratio], enter a ratio using the number keys (in the
range of 25 to 99%).
❖
Priority Setting: Reduce
You can set the ratio with priority when the [Reduce/Enlarge] key is pressed,
followed by the [Reduce] key.
Note
❒ Default:
• Metric version: 71%
• Inch version: 73%
❖
Ratio for Create Margin
You can set a Reduce/Enlarge ratio when registering "Create Margin" in a
Shortcut Key.
Note
❒ Default: 93%
192
Download from Www.Somanuals.com. All Manuals Search And Download.
Reproduction Ratio 2/2
❖
R/E Priority
Specify whether Reduce, Enlarge or Input Ratio is given priority on the dis-
play panel when the [Reduce/Enlarge] key is pressed.
Note
❒ Default: Reduce
4
193
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
Edit 1/2
❖
❖
❖
❖
❖
Front Margin: Left/Right
You can specify left and right margins on the front side of copies in Margin
Adjust mode.
Note
❒ Default:
• Metric version: Left 5mm
• Inch version: Left 0.2"
Back Margin: Left/Right
You can specify left and right margins on the back side of copies in Margin
Adjust mode.
4
Note
❒ Default:
• Metric version: Right 5mm
• Inch version: Right 0.2"
Front Margin: Top/Bottom
You can specify top and bottom margins on the front side of copies in Margin
Adjust mode.
Note
❒ Default:
• Metric version: Bottom 0mm
• Inch version: Bottom 0.0"
Back Margin: Top/Bottom
You can specify top and bottom margins on the back side of copies in Margin
Adjust mode.
Note
❒ Default:
• Metric version: Bottom 0mm
• Inch version: Bottom 0.0"
1 sided
→2 sided Auto Margin:T to T
In 1 sided → 2 sided Duplex mode, you can specify the margins on the back
side.
Note
❒ Default:
• Metric version: Right 5mm
• Inch version: Right 0.2"
194
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit 1/2
❖
❖
1 sided→2 sided Auto Margin:T to B
In 1 sided → 2 sided Duplex mode, you can specify the margins on the back
side.
Erase Border Width
The default setting of the width of the erased margins in Erase Border mode
can be changed as follows:
• Metric version: 3 – 50mm in 1mm steps
• Inch version: 0.1" – 2.0" in 0.1" steps
Note
❒ Default:
• Metric version: 10mm
• Inch version: 0.4"
4
❖
❖
Erase Original Shadow in Combine
In Combine Copy or Booklet/Magazine Copy mode, you can specify whether
to erase a 3mm, 0.1" bounding margin around all four edges of each original.
Note
❒ Default: Yes
Erase Center Width
The default setting of the width of the erased margins in Erase Center mode
can be changed as follows:
• Metric version: 2 – 99mm in 1mm steps
• Inch version: 0.1" – 3.9" in 0.1" steps
Note
❒ Default:
• Metric version: 10mm
• Inch version: 0.4"
195
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
Edit 2/2
❖
Image Repeat Separation Line
You can select a separation line in Image Repeat mode from None, Solid, Bro-
ken A, Broken B, or Crop Marks.
• None
• Solid
4
• Broken A
• Broken B
• Crop Marks
Note
❒ Default: None
❖
Double Copies Separation Line
You can select a separation line in Double Copy mode from None, Solid, Bro-
ken A, Broken B,or Crop Marks.
• None
• Solid
196
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit 2/2
• Broken A
• Broken B
• Crop Marks
Note
❒ Default: None
4
❖
Separation Line in Combine
You can select a separation line in Combine mode from None, Solid, Broken
A, Broken B, or Crop Marks.
• None
• Solid
• Broken A
• Broken B
• Crop Marks
Note
❒ Default: None
197
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
❖
Front Cover Copy in Combine
You can specify whether to make a combined copy on the front cover sheet
when you select Front Cover copy mode.
Note
❒ Default: Combine
❖
Designated Slip Sheet Copy in Combine
You can specify whether to make a combined copy on the inserted slip sheets
in Desig./Chapter Copy mode.
Note
❒ Default: Combine
❖
❖
❖
Copy on Designated Paper
You can specify whether to copy on the designated slip sheets.
4
Note
❒ Default: Yes
Orientation: Booklet, Magazine
You can select the type of originals for Booklet or Magazine mode.
Note
❒ Default: Open to Left
Copy Order in Combine
You can set the copy order in Combine mode to "Left to Right" or "Top to Bot-
tom".
Note
❒ Default: From left to right
198
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
Stamp
Background Numbering
❖
Size
You can set the size of the numbers.
Note
❒ Default: Normal
• Small
• Normal
• Large
4
❖
Density
You can set the density of the numbers.
Note
❒ Default: Normal
Preset Stamp 1/4-4/4
❖
Stamp Priority
You can select the stamp type that is given priority when the {Preset Stamp}
key is pressed.
Note
❒ Default: Copy
❖
❖
Stamp Language
You can select the language of the message that is printed in Stamp mode.
Note
❒ Default: English
Stamp Position
You can set the position at which the stamp is printed.
Press the arrow keys to adjust the position.
Note
❒ Default:
• Metric Version:
• Position: Top right
• Top Margin: 24mm
• Right Margin: 24mm
199
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
• Inch Version:
• Position: Top right
• Top Margin: 1.0"
• Right Margin: 1.0"
❖
Stamp Format
You can adjust the size, density and print page for the stamp.
• Size
You can set the size of the stamp.
Note
❒ Default: 1X
• Density
You can set the pattern used to print the stamp.
4
Note
❒ Default: Normal
❒ Normal: The stamp is printed on the image. You cannot confirm which
parts overlap the image.
❒ Lighter: The image can be seen through the stamp.
❒ Light: You can see the image even clearer than in the "Lighter" setting.
• Print Page
You can select whether the stamp is printed on the first page or all pages.
Note
❒ Default: All Pages
User Stamp 1/2-2/2
❖
Program/Delete Stamp
You can register up to 4 custom stamps with your favorite designs. You can
register/change/delete these designs as user stamps.
For how to Program/Delete Stamp, ⇒ p.131 “Program/Delete User Stamp”.
❖
Stamp Position
You can set the position at which the stamp is printed.
Press the arrow keys to adjust the position.
Note
❒ Default:
• Metric version:
• Position: Top right
• Top Margin: 24mm
• Right Margin: 24mm
200
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
• Inch version:
• Position: Top right
• Top Margin: 1.0"
• Right Margin: 1.0"
❖
Stamp Format
You can adjust the print page for User Stamps 1 to 4 that you registered.
Note
❒ Default: All Pages
Date Stamp
4
❖
Format
You can select the date format for Date Stamp mode.
Note
❒ Default:
• Metric version: DD/MM/YYYY
• Inch version: MM/DD/YYYY
❖
❖
Font
You can select the Date Stamp font.
Note
❒ Default: Font 1
Stamp Position
You can set the position at which the stamp is printed.
Press the arrow keys to adjust the position.
Note
❒ Default:
• Metric version:
• Position: Top left
• Top Margin: 8mm
• Left Margin: 32mm
• Inch version:
• Position: Top left
• Top Margin: 0.3"
• Left Margin: 0.8"
201
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
❖
❖
❖
Stamp Setting
You can select whether the date is printed on the first page or all pages.
Note
❒ Default: All Pages
Size
You can set the Date Stamp size.
Note
❒ Default: Auto
Superimpose
You can select whether the Date Stamp is printed negative when it overlaps
black parts of the image.
4
Note
❒ Default: No
Page Numbering 1/2-2/2
❖
Stamp Format
You can select the page number format that is given priority when the {Page
Numbering} key is pressed.
Note
❒ Default: P1, P2
❖
Font
You can select the font of the page number that is printed in Page Numbering
mode.
Note
❒ Default: Font 1
❖
❖
Size
You can set the size of the stamp that is printed in Page Numbering mode.
Note
❒ Default: Auto
Duplex Back Page Stamping Position
You can set the position of the duplex back page number that is printed in Du-
plex mode.
Note
❒ Default: Opposite Position
202
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
❖
❖
Page Numbering in Combine
You can set how the pages are numbered when you use the Combine function
and Page Numbering function together.
Note
❒ Default: Per original
Stamp on Designated Slip Sheet
You can select whether to print the page number onto slip sheets when you
use the Designate function set to "Copy" and Page Numbering function to-
gether.
Note
❒ Default: No
❖
Stamp Position: P1, P2...Stamp Position: 1/5, 2/5...Stamp Position: —1–, —2–
...Stamp Position: P.1, P.2...Stamp Position: 1, 2...Stamp Position: 1–1, 1–2...
You can set the position at which the stamp is printed.
4
Press the arrow keys to adjust the position.
Note
❒ Default:
• Metric version:
• Position: P1, 1/5, P.1, 1: Top right, -1-, 1-1: Bottom center
• Top/Bottom Margin: P1, 1/5, P.1, 1: 12mm, -1-, 1-1: 8mm
• Left/Right Margin: P1, 1/5, P.1, 1: 12mm, -1-, 1-1: 0mm
• Inch version:
• Position: P1, 1/5, P.1, 1: Top right, -1-, 1-1: Bottom center
• Top/Bottom Margin: P1, 1/5, P.1, 1: 0.5", -1-, 1-1: 0.3"
• Left/Right Margin: P1, 1/5, P.1, 1: 0.5", -1-, 1-1: 0.0"
❖
Superimpose
You can select whether page numbers are printed negative when they over-
lap black parts of the image.
Note
❒ Default: No
203
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
Input/Output
❖
Switch to Batch (SADF)
You can select whether Batch mode or SADF mode is displayed when you
press the Special Original key.
❖
SADF Auto Reset
When you set one original at a time in the document feeder, the Auto Feed
indicator lights for a selected time after an original is fed to show that the doc-
ument feeder is ready for another original. You can adjust this time from 3
seconds to 99.
Note
❒ Default: 5sec.
4
❖
Rotate Sort: Auto Paper Continue
You can specify whether to continue copying when the paper of the required
orientation has run out during rotate-sorting. ⇒ "Rotate Sort" on p.47 “Sort”
• If you select [No]:
When paper of the required orientation runs out, the machine stops copy-
ing and prompts you to supply copy paper. When you load paper, the ma-
chine will continue copying.
• If you select [Yes]:
Copying continues using copy paper of a different orientation. The copy
job will finish even if you have left the machine.
Note
❒ Default: No
❖
❖
Auto Sort
You can specify whether Sort mode is selected when the machine is turned on
or the mode is cleared.
Note
❒ Default: No
Memory Full Auto Scan Restart
When the memory becomes full while scanning originals, the machine can
make copies of the scanned originals first, and then automatically proceed
scanning the remaining originals.
You can enable or disable this function.
• If you select [No]:
When the memory becomes full, the machine stops operation allowing you
to remove the copy pages delivered on the output tray.
• If you select [Yes]:
You can leave the machine unattended to make all the copies, but the re-
sulting sorted pages will not be sequential.
Note
❒ Default: No
204
Download from Www.Somanuals.com. All Manuals Search And Download.
Input/Output
❖
❖
Select Stack Function
Specify whether Stack or Rotate Sort has priority to be shown on the initial
display.
Note
❒ Default: Stack
❒ An optional finisher is required to use this function.
Letterhead Setting
Direction-fixed (top to bottom) or 2-sided paper might not be printed correct-
ly depending on how the originals and paper are placed. If you select "Yes" in
this function, the machine rotates the image correctly.
Note
❒ Default: No
4
205
Download from Www.Somanuals.com. All Manuals Search And Download.
User Tools (Copy/Document Server Features)
4
206
Download from Www.Somanuals.com. All Manuals Search And Download.
5. REMARKS
Do's And Don'ts
• Do not turn off the operation
switch while copying or printing.
Make sure that all copying or
printing has finished.
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
equipment. While moving the
equipment, you should take care
that the power cord will not be
damaged under the equipment.
• The machine might fail to produce
good copy images if condensation
forms inside the machine due to
rapid temperature change.
Important
• Do not open the covers of the ma-
chine while copying or printing. If
you do, misfeeds might occur.
❒ If you want to unplug the power
cord or turn off the main power
switch, make sure that the remain-
ing memory space indicates 100%
on the display for facsimile mode.
• Do not move the machine while
copying or printing.
• If you operate the machine im-
properly or a failure occurs with
the machine, your machine set-
tings might be lost. Be sure to make
a note of your machine settings.
❒ While the machine is unplugged,
you can neither send nor receive a
fax.
Reference
• The supplier shall not be liable for
any loss or damage resulting from
a failure with the machine, loss of
machine settings, or use of the ma-
chine.
For details, see the Facsimile Refer-
ence.
• When you use this machine for a
long time in a confined space with-
out good ventilation, you may no-
tice an odd smell. To keep the
workplace comfortable, we recom-
mend that you keep it well venti-
lated.
• Do not touch areas on or around
the fusing unit. These areas get hot.
• After making copies continuously,
the exposure glass may feel
warm—this is not a malfunction.
• The area around the ventilation
hole might feel warm. This is
caused by exhaust air and is not a
malfunction.
207
Download from Www.Somanuals.com. All Manuals Search And Download.
REMARKS
Where to Put Your Machine
Environments to avoid
Machine Environment
• Locations exposed to direct sun-
light or strong light (more than
1,500 lux).
Your machine's location should be
carefully chosen because environ-
mental conditions greatly affect its
performance.
• Locations directly exposed to cool
air from an air conditioner or heat-
ed air from a heater. (Sudden tem-
perature changes might cause
condensation within the machine.)
Optimum environmental conditions
R CAUTION:
• Locations close to machines gener-
ating ammonia such as a diazo
copy machine.
• Keep the equipment away from
humidity and dust. Otherwise a
fire or an electric shock might oc-
cur.
• Places where the machine might be
subjected to frequent strong vibra-
tion.
5
• Do not place the equipment on
an unstable or tilted surface. If it
topples over, it could cause inju-
ry.
• Dusty areas.
• Areas with corrosive gases.
R CAUTION:
• If you use the equipment in a
confined space, make sure there
is a continuous air turnover.
Moving
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
equipment. While moving the
equipment, you should take care
that the power cord will not be
damaged under the equipment.
• Temperature: 10 –32
°
C(50–89.6
°F)(hu-
midity to be 54% at 32
°
C, 89.6 F)
°
• Humidity: 15 – 80% (temperature
to be 27°C, 80.6°F at 80%)
• A strong and level base.
• The machine must be level within
5mm, 0.2" both front to rear and
left to right.
Important
❒ If you move the machine, you
must be careful as follows:
• To avoid possible buildup of
ozone, be sure to locate this ma-
chine in a large well ventilated
room that has an air turnover of
more than 30 m3/hr/person.
• Turn off the main power ⇒ p.16
“Turning Off the Main Power”
• Unplug the power cord from the
wall. When you pull out the plug
from the socket, grip the plug to
avoid damaging the cord and
causing fire or electric shock.
• Close all covers and trays in-
cluding the front cover and by-
pass tray.
208
Download from Www.Somanuals.com. All Manuals Search And Download.
Where to Put Your Machine
• When the main switch is in the
Stand-by position, the optional
anti-condensation heaters are on.
In case of emergency, unplug the
machine's power cord.
Limitation
❒ Carefully move the machine. If
you do not, the machine might be
damaged or a stored file might be
deleted.
• When you unplug the power cord,
the anti-condensation heaters turn
off.
❒ Do not take off the holding stand.
❒ Avoid any strong shock to the ma-
chine. This could damage the hard
disk and cause stored files to be de-
leted. For precautionary reasons,
files should be copied to another
local computer.
• Make sure that the plug is firmly
inserted in the outlet.
• Voltage must not fluctuate more
than 10%.
• The socket-outlet should be in-
stalled near the equipment and
should be easily accessible.
Power Connection
R WARNING:
5
• Only connect the machine to
the power source described on
the inside front cover of this
manual. Connect the power
cord directly into a wall outlet
and do not use an extension
cord.
Access to the Machine
Place the machine near the power
source, providing clearance as
shown.
1
• Do not damage, break or make
any modifications to the power
cord. Do not place heavy ob-
jects on it. Do not pull it hard
nor bend it more than neces-
sary. These actions could
2
4
cause an electric shock or fire.
3
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
equipment. While moving the
equipment, you should take care
that the power cord will not be
damaged under the equipment.
1. Rear: more than 1 cm (0.4")
2. Right: more than 1 cm (0.4")
3. Front: more than 75 cm (29.6")
4. Left: more than 1 cm (0.4")
R CAUTION:
• When you disconnect the power
plug from the wall outlet, always
pull the plug (not the cable).
Note
❒ For the required space when op-
tions are installed, contact your
service representative.
209
Download from Www.Somanuals.com. All Manuals Search And Download.
REMARKS
Maintaining Your Machine
If the exposure glass, exposure glass
cover, or document feeder belt is
dirty, you might not be able to make
copies as you want. Clean them if you
find them dirty.
Cleaning the Exposure Glass
Cover
❖
Cleaning the machine
Wipe the machine with a soft,
damp cloth. Then, wipe it with a
dry cloth to remove the water.
Important
❒ Do not use chemical cleaner or or-
ganic solvent, such as thinner or
benzene. If they get into the ma-
chine or melt plastic parts, a failure
might occur.
5
❒ Do not clean parts other than those
specified in this manual. Such
parts should be cleaned by your
service representative.
Cleaning the Document Feeder
Cleaning the Exposure Glass
Clean 1 and 2
Clean 1 and 2
210
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Photo Conductor Unit (PCU)
Replacing Photo Conductor Unit (PCU)
When 'Replace photoconductor unit' appears on the panel display, it is time to
replace the photo couductor unit.
R WARNING:
• Do not incinerate the photoconductor unit. Toner dust might ignite
when exposed to an open flame. Dispose of the used photoconductor
unit in accordance with local regulations for plastics.
Note
❒ Do not tilt used PCU after removing it from the machine. If you do, toner
might fall out.
❒ Do not hold the developer cartridge when removing the used PCU from your
machine. If you do, the cartridge might come unlocked and fall.
❒ Do not touch the photo couductor. If you do, abnormal copies might be made.
5
❒ Before you remove the used PCU from the machine, wait until the machine
has completely stopped and is making no sound. Failure to take this precau-
tion could result in a fault.
❒ If there are misfeeds, remove the misfed paper before removing the used
PCU.
❒ Be sure to remove the sealing tape before setting the new PCU. Leaving it on
could cause a fault.
❒ After replacing the PCU, the machine will take about 1 minutes to initialize.
During this period, do not open the front cover or turn off the main switch. If
you do, a fault might occur.
A If the duplex unit is installed, open the duplex unit by pushing the catch
upwards.
211
Download from Www.Somanuals.com. All Manuals Search And Download.
REMARKS
B Open the right cover of the machine by pushing the catch upwards.
C Open the front cover.
5
D While pressing the button, slide the photo conductor unit out until it stops.
212
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Photo Conductor Unit (PCU)
E Raise the green handle and slide the photo conductor unit out towards you.
Important
❒ Do not tilt or drop the removed photo conductor unit. Moving the unit
abruptly can scatter the toner.
❒ While the photo conductor unit is removed, do not change the toner.
5
F Take the new photo conductor unit from the box and remove the plastic
bag, holding the handle.
Important
❒ Do not drop or damage the removed photo conductor unit.
❒ Do not touch the side of the photo conductor unit.
G Put the photo conductor unit removed in step Einto the plastic bag emptied
in step F, keeping the unit at the same angle as when it was installed. Then,
zip the plastic bag.
Note
❒ Do not tilt the used PCU after removing it from the machine. If you do, ton-
er might fall.
H Remove the two red sheets from the photo conductor unit in the order
shown in the illustration.
213
Download from Www.Somanuals.com. All Manuals Search And Download.
REMARKS
Important
❒ Remove the photo conductor unit keeping the unit parallel to the ground
as shown in the illustration. Otherwise, the toner in the unit might scatter.
❒ Do not touch the inside of the unit or the green parts, after the black pro-
tection sheet is removed.
I Align the new photo conductor unit onto the rail of the machine. Slide the
unit all the way into the machine.
5
J Push the unit into the machine until it clicks into place.
K Remove the red sheet from the photo conductor unit and remove the two
pieces of tape.
214
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Photo Conductor Unit (PCU)
L Close the right cover of the machine.
Note
❒ If the right side cover of the machine cannot be closed, it means that the
photo conductor unit has not been properly installed. Slide the photo con-
ductor unit out and push it into the machine again until it clicks into place.
5
M Close the front cover.
N If the duplex unit is installed, close the duplex unit by pushing the catch
upwards.
Note
❒ Confirm that the "Replace PCU" message does not appear on the Opera-
tion Panel.
215
Download from Www.Somanuals.com. All Manuals Search And Download.
REMARKS
5
216
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Specification
Mainframe
❖
❖
❖
❖
❖
❖
❖
❖
❖
❖
Configuration:
Desktop
Photosensitivity type:
OPC drum (Φ30)
Original scanning:
One-dimensional solid scanning system through CCD
Copy process:
Dry electrostatic transfer system
Development:
Dry two-component magnetic brush development system
Fusing:
Heating roll pressure system
Resolution:
600 dpi
Exposure glass:
Stationary original exposure type
Original reference position:
Rear left corner
Warm-up time:
• Main power switch: Less than 15 seconds (20°C, 68°F)
• Operation switch: Less than 10 seconds (20°C, 68°F)
❖
❖
Originals:
Sheet/book/objects
Maximum original size:
A3L, 11" × 17"L
217
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
❖
Copy paper size:
• Tray 1: A3L – A5L, 11" × 17"L – 51/2" × 81/2"L
• Tray 2: A3L – A6L, 11" × 17"L – 51/2" × 81/2"L
• Bypass: A3L – A6L, 11" × 17"L – 51/2" × 81/2"L
• Tray 2 (custom size):
Vertical: 100 – 297mm, 4.0" – 11.7"
Horizontal: 148 – 432mm, 5.9" – 17.0"
• Bypass (custom size):
Vertical: 90 – 305mm, 3.6" – 12.0"
Horizontal: 148 – 600mm, 5.9" – 23.6"
• Duplex: A3L – A5L, 11" × 17"L – 51/2" × 81/2"L (impossible on A5K,
51/2" × 81/2" K)
• LCT: A4K, 81/2" × 11"K
❖
❖
Copy paper weight:
• Paper tray 1: 60 – 90g/m2, 16 – 24 lb.
• Paper tray 2: 52 – 157g/m2, 14 – 42 lb.
• Bypass tray: 52 – 157g/m2, 14 – 42 lb.
6
Non-reproduction area:
• Leading edge: Less than 3 2mm
• Trailing edge: Less than 2 2mm
• Left edge: Less than 2 1.5mm
• Right edge: Less than 2 + 2.5/-1.5mm
❖
❖
First copy time:
Type 1, 2: 5.0 seconds or less
(A4K, 81/2" × 11"K, 100%, feeding from tray 1, on the exposure glass, Text
mode, Auto Image Density)
Copying speed: (Type 1)
• 13 copies/minute (A3L, 11" × 17"L)
• 15 copies/minute (B4L)
• 22 copies/minute (A4K, 81/2" × 11"K)
❖
Copying speed: (Type 2)
• 15 copies/minute (A3L, 11" × 17"L)
• 17 copies/minute (B4L)
• 27 copies/minute (A4K, 81/2" × 11"K)
218
Download from Www.Somanuals.com. All Manuals Search And Download.
Mainframe
❖
Reproduction ratio:
Preset reproduction ratios:
Metric version
400%
200%
141%
122%
115%
100%
93%
Inch version
400%
200%
155%
129%
121%
100%
93%
Enlargement
Full Size
Reduction
82%
85%
75%
78%
71%
73%
65%
65%
50%
50%
25%
25%
6
Zoom: From 25 to 400% in 1% steps (from 25 to 200% in 1% step, when setting
originals in the document feeder).
❖
❖
Maximum continuous copy run:
99 sheets
Copy paper capacity:
• Tray 1, 2: 500 sheets (80g/m2, 20 lb.)
• Bypass tray: 100 sheets (80g/m2, 20 lb.)
❖
Power consumption:
• Mainframe only
Type 1/Type 2
Warm-up
Stand-by
less than 1.44 kW
about 150 W *2
about 650 W *2
During printing
Maximum
less than 1.44 kW
219
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
• Complete system *1
Type 1/Type 2
less than 1.44 kW
about 160 W *2
about 680 W *2
less than 1.44 kW
Warm-up
Stand-by
During printing
Maximum
*1
The Complete System consists of the mainframe, document feeder, 1000-sheet
finisher, duplex unit, internal tray 2, paper tray unit, fax unit, ISDN, extra G3
interface unit, expansion memory, JBIG function upgrade unit, printer unit,
HDD, PHY and memory unit.
*2
The measurements are actual value.
❖
❖
Dimensions (W
Type 1, 2: 550 × 604 × 709mm, 21.7" × 23.8" × 28.0"
×
D
×
H up to exposure glass):
Space for mainframe (W
×
D):
• Type 1, 2: 550 × 604mm, 21.7" × 23.8"
❖
Noise Emission *1
:
Sound Power Level:
• Mainframe only
6
Type 1/Type 2
Stand-by
Copying
Less than 40 dB (A)
Less than 63 dB (A)
• Complete system *3
Type 1/Type 2
Stand-by
Copying
Less than 44 dB (A)
Less than 68.5 dB (A)
Sound Pressure Level *2
• Mainframe only
:
Type 1/Type 2
Stand-by
Copying
Less than 34 dB (A)
Less than 57 dB (A)
• Complete system *3
Type 1/Type 2
Stand-by
Copying
*1
Less than 38 dB (A)
Less than 61 dB (A)
The above measurements made in accordance with ISO 7779 are actual value.
It is measured at the position of the bystander.
*2
*3
The Complete System consists of the mainframe, document feeder, 1000-sheet
finisher, duplex unit, internal tray 2 and paper tray unit.
220
Download from Www.Somanuals.com. All Manuals Search And Download.
Mainframe
❖
❖
Weight:
Type 1, 2: Approx. 55 kg, 121.3 lb.
HDD (Option):
6 GB or more
• Capacity for Document Server
2 GB
• Capacity for Memory sorting
1.5 GB
• Capacity for others
2.5 GB or more
6
221
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Document Feeder (Option)
❖
Mode:
ADF mode, Batch mode, SADF mode, Mixed Size mode, Custom Size origi-
nals mode
❖
Original size:
• A3L – A5KL
• 11" × 17"L – 51/2" × 81/2"KL
❖
Original weight:
• 1-sided originals: 40 – 128g/m2 (11 – 34 lb.)
• 2-sided originals: 52 – 105g/m2 (14 – 28 lb.) (Duplex)
❖
❖
❖
❖
Maximum number of originals:
50 sheets (80g/m2, 20 lb.) or less than 11mm, 0.43"
Maximum power consumption:
Less than 50W (power is supplied from the mainframe)
6
Dimensions (W
550 × 470 × 130mm, 21.7" × 18.6" × 5.2"
×D×H):
Weight:
Approx. 10 kg, 22.1 lb.
Note
❒ Specifications are subject to change without notice.
222
Download from Www.Somanuals.com. All Manuals Search And Download.
500-Sheet Finisher (Option)
500-Sheet Finisher (Option)
❖
Paper size:
A3L, B4L, A4KL, B5K, 11" × 17"L, 11" × 14"L, 81/2" × 14"L, 81/2" ×
11"KL, 81/2" × 13"L, 8" × 101/2"K
❖
❖
Paper weight:
60 – 128g/m2, 16 – 34 lb.
Stack capacity:
• 500 sheets (A4K, 81/2" × 11"K or smaller) (80g/m2, 20 lb.)
• 250 sheets (B4L, 81/2" × 14"L or larger) (80g/m2, 20 lb.)
❖
❖
Staple capacity:
• 30 sheets (A4K, 81/2" × 11"K or smaller) (80g/m2, 20 lb.)
• 20 sheets (B4L, 81/2" × 14"L or larger) (80g/m2, 20 lb.)
Staple paper size:
A3L, B4L, A4KL, B5K, 11" × 17"L, 11" × 15"L, 11" × 14"L, 10" × 14"L,
10" × 15"L, 81/2" × 14"L, 81/2" × 13"L, 81/2" × 11"KL, 8" × 101/2"K, 8" ×
10"K, 101/2" × 71/4"K
6
❖
❖
❖
❖
❖
Staple paper weight:
64 – 90g/m2, 17 – 24 lb.
Staple position:
1 position (upper left)
Power consumption:
48W (power is supplied from the mainframe)
Dimensions (W
350 × 490 × 230mm, 13.8" × 19.3" × 9.1"
×
D
×
H):
Weight:
Approx. 10kg, 22.1 lb.
223
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
1000-Sheet Finisher (Option)
Finisher Proof Tray:
❖
Paper size:
A3L, B4L, A4KL, B5KL, A5KL, B6L, A6L, PostcardL, 11" × 17"L,
11" × 15"L, 11" × 14"L, 10" × 14"L, 10" × 15"L, 81/2" × 14"L, 81/2" × 11"KL,
101/2" × 71/4"KL, 8" × 13"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 101/2"KL, 8"
× 10"KL, 81/4" × 14"L, 51/2" × 81/2"KL
❖
❖
Paper weight:
60 – 157g/m2, 16 – 42 lb.
Stack capacity:
• 250 sheets (A4K, 81/2" × 11"K or smaller) (80g/m2, 20 lb.)
• 50 sheets (B4L, 81/2" × 14"L or larger) (80g/m2, 20 lb.)
Finisher Shift Tray:
❖
Paper size:
6
A3L, B4L, A4KL, B5KL, 11" × 17"L, 11" × 14"L, 81/2" × 14"L, 81/2" ×
11"KL, 101/2" × 71/4"L, 8" × 101/2"KL, 8" × 13L, 81/2" × 13"L, 81/4" ×
13"L, 81/4" × 14"L, 51/2" × 81/2" KL
❖
❖
Paper weight:
60 – 157g/m2, 16 – 42 lb.
Stack capacity:
• 1,000 sheets (A4K, 81/2" × 11"K or smaller) (80g/m2, 20 lb.)
• 500 sheets (B4L, 81/2" × 14"L or larger) (80g/m2, 20 lb.)
❖
❖
Staple capacity:
• 50 sheets (A4K, 81/2" × 11"K or smaller) (80g/m2, 20 lb.)
• 30 sheets (B4L, 81/2" × 14"L or larger) (80g/m2, 20 lb.)
Staple paper size:
A3L, B4L, A4KL, B5KL, 11" × 17"L, 11" × 15"L, 11" × 14"L, 10" × 14"L,
10" × 15"L, 81/2" × 14"L, 81/2" × 11"KL, 101/2" × 71/4"KL, 8" × 13"L, 81/2"
× 13"L, 81/4" × 13"L, 8" × 101/2"KL, 8" × 10"KL, 81/4" × 14"L
❖
❖
Staple paper weight:
64 – 90g/m2, 17 – 24 lb.
Staple position:
• 1 staple – 2 positions
• 2 staples – 2 positions
224
Download from Www.Somanuals.com. All Manuals Search And Download.
1000-Sheet Finisher (Option)
❖
❖
❖
Power consumption:
Less than 50W (power is supplied from the mainframe)
Dimensions (W
527 × 520 × 790mm, 20.8" × 20.5" × 31.1"
×
D
×
H):
Weight:
Approx. 25kg, 55.2 lb.
6
225
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Shift Sort Tray (Option)
❖
Paper capacity:
250 sheets (A4K, 81/2" × 11"K or smaller) (80g/m2, 20 lb.)
125 sheets (B4L, 81/2" × 14" or larger) (80g/m2, 20 lb.)
❖
❖
❖
Power consumption:
3.6 W (power is supplied from the mainframe)
Dimensions (W
430 × 372 × 148 mm, 17" × 15" × 6"
×
D
×
H)
Weight:
Approx. 1.6kg, 3.5 lb.
6
226
Download from Www.Somanuals.com. All Manuals Search And Download.
Duplex Unit (Option)
Duplex Unit (Option)
❖
Paper size:
A3L, B4L, A4KL, B5KL, A5L, 5 1/2" × 8 1/2"L, 7 1/4" × 10 1/2"KL, 8"
× 10"KL, 8 1/2" × 11"KL, 8" × 13"L, 8 1/2" × 13"L, 81/2" × 14"L, 8 1/4" ×
13"L, 11" × 17"L
❖
❖
❖
❖
Paper weight:
64 – 90g/m2, 20 – 24 lb.
Power consumption (Max):
35W (power is supplied from the mainframe)
Dimensions (W
90 × 495 × 455mm, 3.6" × 19.5" × 17.9"
×
D
×
H):
Weight:
Approx. 6kg, 13.3 lb.
6
227
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Internal tray 2 (1 bin tray) (Option)
❖
Number of bins:
1
❖
Available paper size:
A3L, B4L, A4KL, B5KL, A5K, 11" × 17"L, 81/4" × 14"L, 81/2" × 14"L,
11" × 15"L, 11" × 14"L, 10" × 14"L, 10" × 15"L, 81/2" × 11"KL, 101/2" × 71/4"
KL, 8" × 13"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 101/2"KL, 8" × 10"KL,
51/2" × 81/2" L
❖
❖
❖
❖
❖
Paper capacity:
125 sheets (80g/m2, 20 lb.)
Copy paper weight:
60 – 90g/m2 (16 – 24lb.)
Maximum power consumption:
Less than 15 W (power is supplied from the mainframe)
Dimensions (W
530 × 410 × 120mm, 20.9" × 16.2" × 4.7"
×
D
×
H):
6
Weight:
Approx. 1.1 kg, 2.5 lb.
Note
❒ Specifications are subject to change without notice.
228
Download from Www.Somanuals.com. All Manuals Search And Download.
Bypass Tray (Option)
Bypass Tray (Option)
❖
Paper size:
• Standard size: A3L – A6L, 11" × 17"L – 51/2" × 81/2"L
• Custom size: Vertical (100 – 297mm, 4.0" – 11.7"), Horizontal (148 – 432mm,
5.9" – 17.0")
❖
❖
❖
Copy paper weight:
52 – 157g/m2, 14 – 42 lb.
Dimensions (W
296 × 495 × 163mm, 11.7" × 19.5" × 6.5"
×
D
×
H):
Paper capacity:
• 52 – 90g/m2, 16 – 20 lb: 100 sheets
❖
Weight:
Approx. 2.5kg, 5.6 lb.
6
229
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Large Capacity Tray (LCT) (Option)
❖
❖
❖
❖
❖
❖
Paper size:
A4K, 81/2" × 11"K
Paper weight:
60 – 90g/m2, 16 – 24 lb.
Paper capacity:
2,000 sheets (80g/m2, 20 lb.)
Power consumption
Maximum. 40 W (power is supplied from the mainframe)
Dimensions (W
550 × 520 × 271mm, 21.7" × 20.5" × 10.7"
×
D
×
H, option unit):
Weight:
Approx. 25 kg, 55.2 lb.
Note
6
❒ Specifications are subject to change without notice.
230
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper tray unit (Option)
Paper tray unit (Option)
❖
Copy paper weight:
60 – 90g/m2 (16 – 24 lb.)
❖
Available paper size:
A3L, B4L, A4KL, B5KL, A5L, 11" × 17"L, 81/2" × 14"L, 81/2" ×
11"KL, 51/2" × 81/2" L, 81/4" × 14"L, 11" × 14"L, 71/4" × 101/2" K, 8" ×
13"L, 8" × 101/2"KL, 81/2" × 13"L, 81/4" × 13"L
❖
❖
❖
❖
Maximum power consumption:
Less than 30 W (power is supplied from the mainframe)
Paper capacity:
500 sheets (80g/m2, 20 lb.) × 2 trays
Dimensions (W
550 × 520 × 271mm, 21.7" × 20.5" × 10.7"
×
D
×
H):
Weight:
Approx. 25 kg, 55.2 lb.
6
Note
❒ Specifications are subject to change without notice.
231
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
D
Date Stamp, 133
Designate, 145
1000-sheet finisher, 7
500-Sheet Finisher, 7
Directional Magnification (%), 81
Directional Size Magnification (Inch), 83
Display, 10
A
Access to the Machine, 209
Adding Staples, 172
Adding Toner, 162
Auto Off, 30
Display panel, 8, 10
Document Feeder, 222
Document feeder, 5, 32
Cleaning, 210
Document feeder (ADF), 7
Do's And Don'ts, 207
Double Copies, 116
Auto Reduce/Enlarge, 44
B
Duplex unit, 7, 227
Back Cover, 142, 144
Background Numbering, 126
Basic functions, 38
E
Batch mode, 34
Energy Saver key, 8
Energy Saver mode, 71
Enhance, 74
Enlarging, 74
Environment, 208
Book originals, copying, 105, 109
Border Erase, 119, 120
Bridge unit, 7
Bypass tray, 6, 7, 61, 229
Erase
C
Border, 119, 120
Center, 119, 121
Center/Border, 119, 122
Exposure glass, 5, 19, 31
Cleaning, 210
Center/Border Erase, 119, 122
Center Erase, 119, 121
Centering, 117
Changing Paper
Exposure glass cover, 7
Tray 1 or 2, 170
Changing the Paper Size, 170
Chapter, 147
F
Check Modes key, 8
Clearing Misfeeds, 164
Clear Modes key, 8
Clear/Stop key, 9
Combination Chart, 152
Combine, 85, 91
Finisher
1000-Sheet Finisher, 7
500-Sheet Finisher, 7
Front Cover, 142, 144
Front cover, 6
Function Status indicator, 9
Control Panel, 8
Control panel, 5
I
Copying from the Paper Tray 2, 57
Copy Paper, 22, 41
Cover
Image Density, 38, 39
Image Repeat, 115
Indicators, 8
Inter change unit, 7
Internal tray, 5
Back Cover, 142, 144
Front Cover, 142, 144
Internal tray 2 (1 bin tray), 7
Interrupt Copy, 71
Interrupt key, 8
232
Download from Www.Somanuals.com. All Manuals Search And Download.
Program
Changing, 68
J
Job Preset, 70
Deleting, 69
Recalling, 69
Storing, 67
L
Program key, 8
Programs, 67
Large Capacity Tray (LCT), 7, 230
Loading Paper, 160
Large Capacity Tray (LCT), 161
Tray 1-4, 160
R
Reduce/Enlarge, 74
Reducing, 74
M
Remarks, 207
Machine Environment, 208
Mainframe, 217
Main power indicator, 5, 8
Main power switch, 5, 15
Maintenance, 210
Margin Adjustment, 124
Messages, 153
Misfeeds, 164
Remove Paper Indicator, 6
Removing Jammed Staples, 175
Repeat
Image Repeat, 115
Replacing the Photo Conductor Unit, 211
S
Mixed Size mode, 35
SADF mode, 35
Safety information, i
Sample Copy, 72
Sample Copy key, 8
Screen Contrast knob, 8
Series Copies, 105
Shift sort tray, 7
N
Numbering
Background Numbering, 126
Page Numbering, 136
Number keys, 9
Slip Sheets, 142, 149
Sort, 45
O
Sorting copies into sets, 47
Specification, 217
Document Feeder, 222
Duplex unit, 227
Operation switch, 8, 15
Options, 7
Original Beeper, 72
Originals, 18
Internal tray 2 (1 bin tray), 228
Large Capacity Tray (LCT), 230
Mainframe, 217
Original Type selecting, 40
P
Paper tray unit, 231
Shift Sort Tray, 226
Stack, 45, 49
Page Numbering, 136
Paper
Stamp, 126
Changing, 170
Loading, 160
Background Numbering, 126
Date Stamp, 133
Page Numbering, 136
Preset Stamp, 127
User Stamp, 129
Paper tray, 6
Paper tray 2, 6
Paper tray unit, 7
Placing Custom Size Originals, 36
Placing Originals, 31
Power Connection, 209
Preset Stamp, 127
Staple, 45
Staples, 172
Removing Jammed Staples, 175
Stapling copies, 51
Start key, 9
System Reset, 30
233
Download from Www.Somanuals.com. All Manuals Search And Download.
T
Toner, 27
Toner Bottle
Storage, 27
Two-sided Copies, 85, 88
U
User Stamp, 129
User Tools
Copy/Document Server Features, 179
User Tools/Counter key, 8
V
Ventilation holes, 5
Z
Zoom, 77
234
Download from Www.Somanuals.com. All Manuals Search And Download.
|