Kramer Electronics Ltd.
USER MANUAL
Sync Processors Models:
SG-6
SG-7
SG-9
SG-11
SG-6003B
IMPORTANT: Before proceeding, please read paragraph entitled
"Unpacking and Contents"
KRAMER ELECTRONICS LTD.
P/N: 2900-004002
Download from Www.Somanuals.com. All Manuals Search And Download.
1
INTRODUCTION
Congratulations on your purchase of this Kramer Electronics Sync processor. Since 1981 Kramer has been
dedicated to the development and manufacture of high quality video/audio equipment. The Kramer line
has become an integral part of many of the best production and presentation facilities around the world. In
recent years, Kramer has redesigned and upgraded most of the line, making the best even better. Kramer’s
line of professional video/audio electronics is one of the most versatile and complete available, and is a
true leader in terms of quality, workmanship, price/performance ratio and innovation. In addition to the
Kramer line of high quality processors, such as the one you have just purchased, Kramer also offers a full
line of high quality distribution amplifiers, switchers, interfaces, controllers and computer-related
products. This manual includes configuration, operation and information for the following products from
the Kramer line of Sync processors. All these Sync processors are similar in operation and features.
SG-6N - Sync Processor
SG-7 - Sync Transcoder
SG-9 - Sync Processor
SG-11 - Sync to Green Adder/Stripper
SG-6003B - Black Burst/Bar Generator
1.1 A Word on Sync Signals
All video signals received by a monitor carry with them synchronization information. Whether they are
analog signals (Composite, Y/C, Component and RGB) or digital (SDI, etc.), the synchronization signals
are needed for proper alignment of the image on the screen. In most video formats, there are two types of
sync signals: horizontal sync and vertical sync. Many problems, though sync related, are sometimes
misinterpreted, and other components of the signals are blamed instead.
1.1.1 Horizontal Sync
The horizontal sync in a composite video signal (often referred to as line sync) is a short, negatively
directed pulse, found at the beginning of each scan line of the monitor (see Figure 1). Basically, this pulse
“tells” the monitor: “be prepared, a line of data is coming”. Horizontal sync resides in the blanking area
(the unseen part of the signal), and so is not visible on the screen. The number of line sync pulses equals
the number of video lines.
Figure 1: Horizontal Sync
Kramer Electronics Ltd.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical sync, often referred to as the field sync (see Figure 2), is also a negatively directed set of pulses,
found at the beginning of each video field (60 field/sec. in NTSC, 50 fields/sec. in PAL). Vertical sync is a
more complicated signal than horizontal sync, which tells the monitor: “be prepared, a new field of data is
coming”. Vertical sync also resides in the blanking area, and is not visible on the screen.
Figure 2: Vertical Sync
1.1.2 Sync location
Sync location varies according to video format, as follows:
ꢀ
In the Composite video signal it is an integral part of the signal as Composite is a “package” including
sync (horizontal and vertical), luminance (Y) and chrominance (color) information.
ꢀ
ꢀ
ꢀ
The s-Video signal format has two parts: luminance (brightness, black & white) and chrominance
(color) information. The sync signals in this format are part of the luminance (Y) signal.
The Component video signal is comprised of three signals – luminance (Y) and two different color
signals, R-Y and B-Y. The sync signals reside in the Y signal.
When it comes to RGB (Red, Green, Blue) signals used in professional computer graphics and display
applications, there are several options for the sync signals to be carried along with the data. The first
and most common one is in a separate analog sync channel. This format uses 4 wires carrying signals
and is called RGBS.
ꢀ
Another popular format uses only three wires – Red and Blue (as in the above configuration) and
Green+Sync, where the sync rides on the green signal. In this format, the signal levels are not
identical as the Green signal has a larger amplitude due to the sync it carries, and the sync signals
must be tripped off in order to recover the normal green sync level.
ꢀ
ꢀ
A subset of this format inserts the sync signals in all three data channels – e.g., Red+Sync, Blue+Sync
and Green+Sync.
The format generated by a computer graphics card is normally made of 5 different signals: Red,
Green, Blue, Horizontal sync and Vertical sync (sometimes referred to as Hs and Vs.) To make things
more complicated, the data channels (R, G, B) are analog channels (their level varies in a continuous
way from 0 to maximum) but the sync signals are digital format signals (TTL level) being either "0"
or "1" (0V or 5V). To make things even more complicated, in contrast to the analog sync signals that
are negatively directed pulses, the computer generated logic-level syncs can appear in both directions.
Sometimes one of the syncs is positive and the other is negative, sometimes both are either positive or
negative. The sync direction is dictated by the source (the graphics card) and is dependent on the
required resolution. In the past, the sync direction instructed the monitor which resolution to choose.
Today, most of the monitors are smarter and set the resolution automatically, but nevertheless, the
cards still generate those sync signals.
Kramer Electronics Ltd.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
Another twist to this format is that in most cases the logic-level syncs are separated and run each in its
own channel, but there are cases where the logic-level syncs come composite – joined together in the
same mix of directions.
ꢀ
ꢀ
In the digital world – SDI, DV, MPEG and other formats, the synchronization signals either travel in a
special digital sync channel or, in most cases, are embedded in the digital signal.
Due to the extensive use of sync related products, serious problems concerning sync signals may arise
such as improper analog sync levels, damaged vertical sync, sync deterioration and improper polarity
of the horizontal and vertical syncs.
1.2 Video Sync Processors
Kramer Electronics has a full line of Video Sync Processors that can perform sync stabilization, restoration
and conversion n the following categories:
ꢀ
ꢀ
Video Sync Generators: Generate standard video sync and black burst for studio genlock.
Video Sync Converters: Convert between the different sync formats - Composite, separate H & V
syncs and Analog or TTL level. One machine in this category does sync to Green adding and
separating.
ꢀ
Video Sync Restorers: Restore and re-build lost or distorted sync signals and full black burst signals.
1.3 Factors Affecting Quality of Results
There are many factors affecting the quality of results when signals are transmitted from a source to an
acceptor as described in Table 1:
Table 1: Factors Affecting Quality of Results
FACTOR
EFFECT
Low quality cables are susceptible to interference; they degrade signal quality
Connection cables:
due to poor matching and cause elevated noise levels. They should therefore be
of the best quality.
Sockets and connectors of
So often ignored, they should be of highest quality, since "Zero Ohm" connection
the sources and acceptors: resistance is the objective. Sockets and connectors also must match the required
impedance (75ohm in video). Cheap, low quality connectors tend to rust, thus
causing breaks in the signal path.
Amplifying circuitry:
Must have quality performance when the desired end result is high linearity, low
distortion and low noise operation.
Distance between sources
and acceptors:
Plays a major role in the final result. For long distances between sources and
acceptors, special measures should be taken in order to avoid cable losses. These
include using higher quality cables or adding line amplifiers.
Interference from
neighboring electrical
appliances:
These can have an adverse effect on signal quality. Balanced audio lines are less
prone to interference, but unbalanced audio should be installed far from any
mains power cables, electric motors, transmitters, etc. even when the cables are
shielded.
Kramer Electronics Ltd.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2
SPECIFICATIONS
SG-6N
SG-7
INPUT CHANNEL 1: One composite sync >0.3Vpp /
75 ohm or 1 TTL level composite sync 5 Vpp/ 47k on a
BNC type connector with Hi-Z/75ohm switch, at video
frequencies only.
Input
1 Composite video,
1Vpp/75 ohms on a BNC
connector.
INPUTS CHANNEL 2: H and V TTL level syncs, any
polarity and any frequency, 5 Vpp / 47k on BNCs.
INPUTS CHANNEL 3: H and V looping analog syncs,
> 0.3Vpp / 75ohm with termination switches on BNCs,
at any frequency.
Output
1 restored composite video OUTPUTS CHANNEL 1: H and V syncs on BNCs -
1Vpp/75 ohm on BNC type TTL level, 1 Vpp when 75ohm loaded, 15khz, 50/60
connector.
Hz.
OUTPUTS CHANNEL 2: Composite TTL level sync
on a BNC, 1Vpp when 75ohm loaded.
OUTPUTS CHANNEL 3: Composite analog sync
1Vpp/75ohm on a BNC and a TTL level composite
sync. (or 1Vpp/75ohm analog when terminated with a
75ohm resistor) on an additional BNC.
Video Bandwidth 25MHz -3dB
Differential Gain 0.35%
Differential Phase 1Deg.
Video S/N Ratio 74dB
Max. Signal
output
2Vpp/75ohm
Dimensions
(W, D, H)
12cm x 6.5cm x 4.5cm
4.7" x 2.5" x 1.8"
48 x 17.8 x 1U
19" x 7" x 1U
Weight
0.58kg. (1.3lbs.) Approx. 2.3kg. (5.1 lbs.) Approx.
12VDC, 40mA 230VAC, 50/60Hz, 3.2VA (115VAC, U.S.A.)
Power Source
Kramer Electronics Ltd.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SG-9
SG-11
SG-6003B
1 Green 0.7Vpp/75 ohm
One Sync 0.3Vpp/75
ohm on BNCs.
Input
1 composite video
1Vpp/75 ohm on a BNC.
1 restored composite
video 1Vpp/75 ohm on a 75 ohm on a BNC.
BNC.
1 Sync on Green 1Vpp /
Output
3 black burst signals, 0.3 Vpp/75
ohm, (sync) 1 color bar output
1Vpp/75ohm, 1 subcarrier
output, 1Vpp/75 ohm on BNC
connectors. Two audio tone @
1kHz, 1Vpp/100ohm outputs on
RCA connectors.
1 Green 0.7Vpp / 75
ohm, One Sync 1Vpp /
75 ohm on BNCs.
Video
Bandwidth
35MHz, 1dB
0.8%
21MHz, 3dB
Differential
Gain
Differential
Phase
0.5Deg.
0.1%
K-Factor
Video S/N Ratio
Better than 73dB
2Vpp/75ohm.
Max. Signal
output
2Vpp/75ohm.
Phase Error
Less than 1 degree
Color Bar
Saturation
Preset to 75%, may be ordered
at 100%
Sync Oscillator
SC oscillator
Sync/SC
Crystal controlled
Crystal controlled
Fully Genlocked
Better than 50PPM
Stability
Dimensions
(W, D, H)
24.5cm x 18cm x 4.5cm 24.5cm x 18cm x 4.5cm 48 x 17.8 x 1U
9.6" x 7" x 1.8" 9.6" x 7" x 1.8" 19" x 7" x 1U
Weight
1.5kg. (3.3lbs.) Approx. 2.9kg. (6.4lbs.) Approx. 2.4kg. (5.3lbs.) Approx.
Power Source
230VAC, 50/60 Hz
(115VAC, U.S.A.)
4.3VA.
230VAC, 50/60 Hz,
(115VAC, U.S.A.)
4.1VA
230 VAC, 50/60 Hz, (115VAC,
U.S.A), 5.7VA
Kramer Electronics Ltd.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
HOW DO I GET STARTED?
The fastest way to get started is to take your time and do everything right the first time. Taking 15 minutes
to read the manual may save you a few hours later. You don’t even have to read the whole manual. If a
section doesn’t apply to you, you don’t have to spend your time reading it.
UNPACKING AND CONTENTS
The items contained in your Kramer Sync Processor package are listed below. Please save the original box
and packaging materials for possible future transportation and shipment.
1. Sync Processor
2. Rubber Feet
3. User Manual
4. Kramer Concise Product Catalog
5. AC Power Cable (where applicable)
4.1 Optional Accessories
The following accessories, which are available from Kramer, can enhance implementation of your
machine. For information regarding cables and additional accessories, contact your Kramer dealer.
❒
Mechanical Rack Adapter - Used to adapt non-standard size machines to a standard 1U rack. One
or more machines may be installed on each adapter.
❒
VM-1015 (1:5 Video Distribution Amplifier) can be serially inserted between the sync processor and
other machines for signal distribution. It is designed for studio and other demanding applications.
The VM-1015 splits a single input source into five identical outputs with no discernible signal
degradation. Output signals can either be AC or DC coupled, black level or sync tip clamped, thus
allowing the machine to function in all video environments. The machine may be used to distribute
analog or SDI (Serial Digital) video signals, composite or single component. Video bandwidth of
well over 340MHz and superb specifications make the VM-1015 the ultimate distributor for all video
applications.
❒
VIDEO TESTER - A new, unique, patented, indispensable tool for the video professional, the video
Tester is used to test a video path leading to/from an amplifier. By pressing only one touch switch it
can trace missing signals, distinguish between good and jittery (VCR sourced) signals, and identify
the presence of good signals. Whenever a video signal is missing, because of bad connections, cable
breaks or faulty sources, the video Tester is all you need.
Kramer Electronics Ltd.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5
SYNC PROCESSORS
This section describes all the controls and connections of your machine. Understanding the controls and
connections helps you realize the full power of your machine.
5.1 Getting to Know Your SG-6N Sync Stabilizer
The KRAMER SG-6N Video Sync Stabilizer replaces corrupted or missing horizontal and Vertical sync
information from a video signal, especially from high generation tapes carrying time-code or teletext
information which upset image stability, with standard synchronization signals. In many cases the
KRAMER SG-6N can replace or enhance a TBC operation. The SG-6N restores standard sync and
blanking information, eliminating instability of the video signal. The SG-6N operates in PAL and NTSC,
and a rear panel mounted switch selects operation mode. The machine uses 12VDC for power supply and
is therefore suitable for fieldwork as well.
Front/Rear panel features of the SG-6N are described in Figure 3 and Table 2.
NOTE
For operation instructions refer to section 9.
Figure 3: SG-6N Front/Rear Panel Features
Table 2: SG-6N Front/Rear Panel Features
No.
Feature
Function
1. Power Switch
2. CV IN BNC connector
3. Switch
4. CV OUT BNC connector
5. 12VDC feed connector
Illuminated switch: Supplies power to the unit.
Composite video input.
Selects either NTSC or PAL mode (pressed = NTSC).
Restored composite video output.
A DC connector that allows power to be supplied to the unit.
Kramer Electronics Ltd.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Getting to Know Your SG-7 Sync Transcoder
The KRAMER SG-7 Universal Sync Transcoder interfaces between the widely used professional video
sync formats - Composite sync, Horizontal sync, Vertical sync - Analog and TTL levels. In many video
studios and professional applications there is a need to convert from one format to the other, and the
KRAMER SG-7 is the perfect choice - as it operates simultaneously in all directions.
Front/Rear panel features of the SG-7 are described in Figure 4 and Table 3.
NOTE
For operation instructions refer to section 9.
Figure 4: SG-7 Front/Rear Panel Features
Table 3: SG-7 Front/Rear Panel Features
No.
Feature
Power switch
C sync In BNC connector
Function
1.
2.
3.
Illuminated switch: Supplies power to the unit.
Composite sync input.
Selects “75ohm“ or “HI-z” impedance when pressed (for
looping select "Hi-z").
75ohm/Hi-Z switch
4.
5.
6.
7.
8.
9.
Loop BNC connector
Provides looping capability of the composite sync input.
Vertical sync output.
Horizontal sync output.
TTL level vertical sync input.
TTL level horizontal sync input.
Composite sync output.
Vs Out BNC connector
Hs Out BNC connector
TTL Vs In BNC connector
TTL Hs In BNC connector
CS Out BNC connector
10. Hs In BNC connector
11. Loop BNC connector
12. Vs In BNC connector
13. Loop BNC connector
14. CS Out 1, 2 BNC connector
15. Power Connector
Horizontal sync input.
Provides looping capability of the "H" input.
Vertical sync input.
Provides looping capability of the "V" input.
Composite sync outputs.
A 3-prong AC Connector allows power to be supplied to the
unit. Directly underneath this connector, a fuse holder houses the
appropriate fuse.
Kramer Electronics Ltd.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Getting to Know Your SG-9 Video Black Burst Restorer
The KRAMER SG-9 Video Black Burst Restorer replaces corrupted or missing horizontal and vertical
syncs as well as color burst from a video signal with standard synchronization and color signals. In many
cases the KRAMER SG-9 can replace or enhance a TBC operation. The SG-9 generates standard sync and
color information from internal high quality, genlocked, sync and color generators.
Front/Rear panel features of the SG-9 are described in Figure 5 and Table 4.
NOTE
For operation instructions refer to section 9.
Figure 5: SG-9 Front/Rear Panel Features
Table 4: SG-9 Front/Rear Panel Features
No.
Feature
Power switch
VIDEO IN BNC connector
SYNC OUT BNC connector
VIDEO OUT BNC connector
Power Connector
Function
1.
2.
3.
4.
5.
Illuminated switch: Supplies power to the unit.
Composite video input.
Composite sync output.
Restored composite video output.
A 3-prong AC Connector allows power to be supplied to the
unit. Directly underneath this connector, a fuse holder houses the
appropriate fuse.
Kramer Electronics Ltd.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4 Getting to Know Your SG-11 Sync to Green Adder/Stripper
The KRAMER SG-11 Sync to Green Adder/Stripper interfaces between the two most widely used
professional Component Video formats - RGB with Sync On Green and RGBS. In many video studios and
production centers there is a need to convert from one format to the other and the KRAMER SG-11 is the
perfect choice - as it operates simultaneously in both directions.
Front/Rear panel features of the SG-11 are described in Figure 6 and Table 5.
NOTE
For operation instructions refer to section 9.
Figure 6: SG-11 Front/Rear Panel Features
Table 5: SG-11 Front/Rear Panel Features
No.
Feature
Power switch
Function
1.
2.
3.
4.
5.
6.
7.
8.
Illuminated switch: Supplies power to the unit.
Green signal input.
Green in BNC connector
Sync in BNC connector
G+S out BNC connector
G+S in BNC connector
Green out BNC connector
Sync out BNC connector
Sync Tip switch
Sync signal input.
Combined Green + Sync output.
Combined Green + Sync input.
Separated Green output.
Separated Sync output.
Selects either clamping the signal to a predefined -1VDC level or to
0VDC level.
9.
Power Connector
A 3-prong AC Connector allows power to be supplied to the unit.
Directly underneath this connector, a fuse holder houses the
appropriate fuse.
Kramer Electronics Ltd.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5 Getting to Know Your SG-6003B Black Burst/Color Bar Generator
The KRAMER SG-6003B is a broadcast level Black Burst/Color Bar Generator for video studio
applications. The SG-6003B provides three identical Black Burst outputs, a color Subcarrier output, a
Color Bar output and two 1 kHz, crystal stabilized audio outputs. State-of-the-art technology is used
throughout the SG-6003B - crystal controlled sync and Chroma oscillators, accurate internal
sync/Subcarrier genlock, both with long term stability. The number of outputs may be increased by using
one of the Kramer Broadcast video DAs, e.g., VM-1010, VM-1015, VM-1021, etc.
Front/Rear panel features of the SG-6003B are described in Figure 7 and Table 6.
NOTE
For operation instructions refer to section 8.
Figure 7: SG-6003B- Front/Rear Panel Features
Table 6: SG-6003B - Front/Rear Panel Features
No.
Feature
Function
1.
2.
Power switch
Internal trimmers (bottom accessible)
Illuminated switch: Supplies power to the unit.
Not for user adjustments.
WARNING!
3.
4.
5.
6.
Adjustments or attempted adjustments of the
trimmers is not allowed. Failure to comply
with this warning may damage the machine.
7.
8.
9.
10.
11. 1KHz Out RCA connectors
12. Black Burst Outputs BNC
connectors
1KHz crystal stabilized audio outputs.
Black Burst identical outputs.
13. BAR BNC connector
14. SC out BNC connector
15. Power Connector
Color bar output.
Color subcarrier output.
A 3-prong AC connector allows power to be supplied to the
unit. Directly underneath this connector, a fuse holder houses
the appropriate fuse.
Kramer Electronics Ltd.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
6
INSTALLATION
6.1 Rack Mounting
The SG-7 and the SG-6003B can be rack mounted in a standard 19” (1U) EIA rack, and include rack
“ears” at the ends of the front panel. To rack mount these machines, simply place the unit's ears against the
rack rails of your rack, and insert standard screws through each of the four corner holes. The SG-6N, SG-9
and the SG-11 can be rack mounted using a special adapter (see section 4.1). None of these devices require
any specific spacing for ventilation above or below the unit.
6.2 Connecting To Video Devices
Video sources and output devices (such as recorders) may be connected to the machines through the BNC
type connectors located on the back of the unit. Unused inputs are terminated to 75ohm, and active inputs
should be terminated by the connecting source.
7
USING THE MACHINES
7.1 Powering on the machine
NOTES
ꢀ
ꢀ
The machine should only be powered on, after all connections are
completed, and all source devices have been powered on. Do not attempt to
connect or disconnect any video to the machine while it is powered on!
The socket-outlet should be near the equipment and should be easily
accessible. To fully disconnect equipment, remove power cord from socket.
1) Press the power switch on the machine's front panel and verify that it glows.
2) Operate the acceptors.
7.2 NTSC/PAL Selection (SG-6N only)
There are several different video standards used in different countries. The leading standards are PAL,
used in most European countries, NTSC used in the US, in Japan and some other countries and SECAM,
which is used mainly in France, and some other countries. Each standard uses different color encoding
schemes. Sync related problems might be encountered during NTSC or PAL operation include:
1) Problems with the sync information carried along with the video signal.
2) Problems of sync signal compatibility with the users’ system.
To select PAL or NTSC, simply select the required system using the NTSC/PAL switch located on the
rear panel (pressed = NTSC).
7.3 Looping (SG-7 only)
The looping function enables the operator to connect several machines to a video source. The operator
must always switch the termination switch of the first and middle machines to "Hi-z". The last machine's
termination switch should always be at "75ohm" to maintain well-matched lines (of 75ohm impedance)
from the first to the last machine. If the looping function is not used, the termination switch should be set
to "75 ohm".
7.4 Clamping (SG-11 only)
Clamping is an electronic process which corrects line-by-line the video blanking level or "sync tip" by
clamping it to a predefined DC level. The process reduces the DC level changes when switching between
different sources, eliminates picture jumps on the screen, the accumulation of low frequency noise and
instability. Clamping also increases the dynamic range of video devices by limiting the average picture
changes, which stress the video device. When dealing with composite video signals, it is recommended to
perform DC clamping to -1V and RGB signals should be clamped to 0V. Unwanted DC offsets can also be
Kramer Electronics Ltd.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
removed in the same way by performing proper clamping. To clamp the DC level to -1V or 0V select the
desired level using the -1V/0V switch located on the machine's rear panel.
8
9
TAKING CARE OF YOUR PROCESSOR
Do not locate your processor in an environment where it is susceptible to dust or moisture and temperature
and humidity may be excessive. All of these may damage the electronics, and cause erratic operation or
failure. Do not clean your processor with abrasives or strong cleaners. Doing so may remove or damage
the finish, or may allow moisture to build up. Take care not to allow dust or particles to build up inside
unused or open connectors.
TYPICAL APPLICATIONS
9.1 Stabilizing the Video Sync
As the sync information is vital for video image stability on the screen, deterioration or loss of the sync
signals affects image stability. Both Horizontal and Vertical sync signals are crucial for image stability and
proper image centering on the screen. When the sync signals are damaged during transmission or recording
they may be recovered by a sync restoring device. Another problem of sync compatibility is a result of the
many standards for transferring the sync information with the signal: sync signals may come in analog
form, as a composite sync signal, in digital form, either as composite or separate Horizontal and Vertical,
positive direction or negative. The sync signals may be part of the luminance signals or ride on a video
component signal such as the “Green” signal. To solve this compatibility problem, special devices such as
sync format converters are needed. Typical video sync stabilization is described in Figure 8: A corrupted
video signal is applied to a Video Sync Stabilizer's input (SG-6N in this case). The SG-6N removes of
unwanted interference and signal distortions and the restored signal is outputted to an appropriate acceptor.
Figure 8: Stabilizing the Video Sync
Kramer Electronics Ltd.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
9.2 Black Burst/Bar Generator Connections
Figure 9 describes typical usage of a Black Burst/Bar Generator, where the SG-6003B functions as a test
and alignment tool for the audio and video acceptors and can provide black or color reference bar for
cameras that need a stable reference. A Subcarrier signal is also provided to a Chroma Keyer/Mixer for
special effects operation.
Perform the following steps (as necessary):
1) Connect an audio acceptor to the 1 kHz Out RCA connectors of the SG-6003B.
2) Connect the BNC Black Burst Outputs connectors of the SG-6003B to genlockable
acceptors/sources.
3) Connect the BAR BNC connector to a video monitor.
4) Connect the SC Out BNC connector to a Chroma Keyer/Mixer.
5) Operate sources/acceptors, mixer and the SG-6003B.
Figure 9: Black Burst/Bar Generator Connections
9.3 Restoring Black Burst and Image Stability
Figure 10 illustrates typical usage of a Kramer Sync processor (SG-9 in this case): an unstable video signal,
coming from a video source is connected to the SG-9, in order to restore the bad image. A video acceptor
is connected to the SG-9 output and receives the restored image.
Perform the following steps (as necessary):
1) Connect the output from your video source to the VIDEO IN BNC connector of the SG-9.
2) Connect the VIDEO OUT connector of the SG-9 to an appropriate acceptor.
3) Operate sources/acceptors and the SG-9.
Kramer Electronics Ltd.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 10: Restoring Black Burst and Image Stability
9.4 Transcoding Various Sync Formats
Transcoding between various video sync formats can be performed by the SG-7, as described in Figure 11.
Perform the following steps (as necessary):
1) Connect a composite sync source to the C Sync In BNC connector of CHANNEL 1. If looping is not
needed, switch the termination switch to "75ohm" position.
2) Connect TTL level H & V syncs into the inputs of CHANNEL 2.
3) Connect ANALOG H & V syncs into the inputs of CHANNEL 3. If looping is not needed, switch the
termination switch to "75ohm" position.
4) Connect all acceptors to the appropriate outputs. All channels can be operated simultaneously.
Channel 3 has two outputs: CS OUT1 is analog only and CS OUT2 is TTL level but can be
converted to analog by loading this output with 75ohm load. Cross linking between inputs and outputs
is allowed, however some delay will be created due to the long processing chain.
5) Operate source, acceptors and the SG-7.
Kramer Electronics Ltd.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 11: Transcoding Various Sync Formats
Kramer Electronics Ltd.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
10 TROUBLESHOOTING
NOTES
1. Please note that if the output signal is disturbed or
interrupted by very strong external electromagnetic
interference, it should return and stabilize when such
interference ends. If not, turn the power switch off and on
again to reset the machine.
2. If the following recommended actions still do not result in
satisfactory operation, please consult your KRAMER
Dealer.
10.1 Power and Indicators
Problem
No Power
Remedy
1. Confirm that the rocker switch is in the “ON” position, and that the light
glows.
2. Confirm that power connections are secured at the machine and at the
receptacle. Make sure the mains receptacle is active (SG-7, SG-9, SG-11,
SG-6003B) or that the DC power supply is operational (SG-6N).
ꢁ
For the SG-7, SG-9, SG-11, SG-6003B perform the following:
1. If still there is no power, remove power cord from AC outlet and then,
using a flat head screwdriver, remove the fuse holder located directly
below the power connector on your machine. Confirm that the fuse is good
by looking for the wire connected between the ends of the fuse. If the wire
is broken, replace the fuse with another, with the same rating.
ꢁ
For the SG-6N perform the following:
1. Using a Philips screwdriver, remove the 4 side screws attaching the
machine's cover.
2. Locate the fuse holder inside your machine (see Figure 12). Confirm that
the fuse is good by looking for the wire connected between the ends of the
fuse. If this wire is broken, replace the fuse with another, with the same
rating.
3. Install cover by replacing the Philips screws.
Kramer Electronics Ltd.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 12: SG-6N Fuse Location
Remedy
10.2 Video Signal
Problem
1. Confirm that your source and output devices are powered on and
connected properly. The input of your machine should be of an identical
signal format at the output of your source. Signals at the output of your
machine should be of an identical signal format as at the input of your
display.
No video at the output
device
2. Confirm that any other device in the signal path have the proper input
and/or output selected.
3. Use the Video Tester to help trace faulty cables and equipment (see
section 4.1).
1. Verify that the lines are well matched through 75ohm impedance;
otherwise it results in a video level that is too high or too dim.
2. Confirm that the connecting cables are of high quality and properly
inserted.
Video level is too high or
too dim.
3. Check level controls located on your source input device or output display.
Hum bars (ground loop) are caused by a difference in the ground potential of
any two or more devices connected to your signal path. This difference is
compensated by passing that voltage difference through any available
interconnection, including your cables.
Noise bars are "rolling"
up or down in the output
image
or:
WARNING!
Low Frequency Hum in
the output signal
Do not disconnect the ground from any
piece of equipment in your signal path!
Check the following to remove hum bars:
1. Confirm that all interconnected equipment is connected to the same phase
of power, if possible.
2. Remove equipment connected to that phase that may introduce noise, such
as motors, generators, etc.
3. Disconnect all interconnecting cables and reconnect them one at a time
until the ground loop reappears. Disconnect the affected cable and replace,
or insert an isolation transformer in the signal path.
4. Use a video Isolator, such as Kramer OC-1N or a differential amplifier
such as Kramer 123V inserted in the video signal path.
Kramer Electronics Ltd.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Kramer Electronics (hereafter Kramer) warrants this product to be free from defects in material and
workmanship under the following terms.
HOW LONG IS THE WARRANTY
Labor and parts are warranted for three years from the date of the first customer purchase.
WHO IS PROTECTED
Only the first purchase customer may enforce this warranty.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as below, this warranty covers all defects in material or workmanship in this product. The following are
not covered by the warranty:
1) Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer
dealer. If you are uncertain as to whether a dealer is authorized, please contact Kramer at one of the agents
2) Any product, on which the serial number has been defaced, modified or removed.
3) Damage, deterioration or malfunction resulting from:
a) Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature.
b) Unauthorized product modification, or failure to follow instructions supplied with the product.
c) Repair or attempted repair by anyone not authorized by Kramer.
d) Any shipment of the product (claims must be presented to the carrier).
e) Removal or installation of the product.
f) Any other cause, which does not relate to a product defect.
g) Cartons, equipment enclosures, cables or accessories used in conjunction with the product.
WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR
We will pay labor and material expenses for covered items. We will not pay for the following:
1) Removal or installations charges.
2) Costs of initial technical adjustments (set-up), including adjustment of user controls or programming. These
costs are the responsibility of the Kramer dealer from whom the product was purchased.
3) Shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1) To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center.
2) Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of
warranty coverage, and should be included in any shipment of the product. Please also include in any
mailing a contact name, company, address, and a description of the problem(s).
3) For the name of the nearest Kramer authorized service center, consult your authorized dealer.
LIMITATION OF IMPLIED WARRANTIES
All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited
in duration to the length of this warranty.
Kramer Electronics Ltd.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
EXCLUSION OF DAMAGES
Kramer’s liability for any defective products is limited to the repair or replacement of the product at our option.
Kramer shall not be liable for:
1) Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use
of the product, loss of time, commercial loss; or:
2) Any other damages, whether incidental, consequential or otherwise. Some countries may not allow
limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from place to
place.
NOTE: All products returned to Kramer for service must have prior approval. This may be obtained from your
dealer.
NOTICE
This equipment has been tested to determine compliance with the requirements of:
EN-50081:
"Electromagnetic compatibility (EMC);
Generic emission standard.
Part 1: Residential, commercial and light industry"
EN-50082:
"Electromagnetic compatibility (EMC) generic immunity standard. Part 1:
Residential, commercial and light industry environment".
CFR-47
FCC Rules and Regulations:
Part 15- “Radio frequency devices:
Subpart B- Unintentional radiators
CAUTION!
ꢀ
Any user who makes changes or modifications to the unit without the express approval of the
manufacturer will void warranty and user authority to operate the equipment. Only a qualified
technician approved by Kramer Electronics should service the machine.
ꢀ
ꢀ
Use the supplied AC power cord (when applicable) to supply power to the machine and controllers.
Please use recommended interconnect cables to connect the machine to controllers and other
components.
Kramer Electronics Ltd.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
The list of Kramer distributors appears on our web site:
From the web site it is also possible to e-mail factory headquarters.
We welcome your questions, comments and feedback.
Kramer Electronics Ltd.
3 Am VeOlamo Street. Jerusalem 95463, Israel Tel: (972-2)-654-4000. Fax: (972-2)-653-5369
e-mail: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|