JOHN DEERE
WORLDWIDE COMMERCIAL & CONSUMER
EQUIPMENT DIVISION
Pressure Washer
3000
OMM156510
OPERATOR’S MANUAL
WARNING
Failure to read and follow the
Operator’s Manual and all operating
instructions can result in death, bodily
injury, and/or property damage. Save
this manual for future reference.
North American Edition
Litho in USA
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT IDENTIFICATION
Record Identification Numbers
Pressure Washer
If you need to contact an Authorized Dealer for information on
servicing, always provide the product model and identification
numbers.
You will need to locate the model, revision and serial number for
the machine and record the information in the places provided
below. You will also need the model and serial number for the
engine on your machine. See the engine operators manual for the
location of these numbers.
DATE OF PURCHASE:
DEALER NAME:
DEALER PHONE:
A
PRODUCT IDENTIFICATION NUMBERS
MODEL (A):
REVISION:
SERIAL NUMBER
ENGINE
MODEL:
SERIAL NUMBER:
Product Identification
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Daily Operating Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SERVICE PRESSURE WASHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
STORAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
GETTING QUALITY SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SERVICE RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
John Deere® and the leaping deer logo are registered
trademarks of Deere & Co. and are used under license to
Briggs & Stratton Power Products.
All information, illustrations and specifications in this manual
are based on the latest information at the time of publication.
The right is reserved to make changes at any time without
notice and without incurring obligation.
Copyright © 2007 Briggs & Stratton
Power Products Group, LLC.
All rights reserved.
No part of this material may be reproduced or transmitted in
any form by any means without the express written
permission of
Briggs & Stratton Power Products Group, LLC.
OMM156510
Table Of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Understanding The Machine Safety Labels
The machine safety label shown below is placed on your machine
to draw attention to potential safety hazards.
Safety - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SAVE THESE INSTRUCTIONS
WARNING
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth
defects, or other reproductive harm.
Safety Rules
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
WARNING
Running engine gives off carbon monoxide, an
odorless, colorless, poison gas.
Breathing carbon monoxide can cause headache,
fatigue, dizziness, vomiting, confusion, seizures,
nausea, fainting or death.
Some chemicals or detergents may be harmful if
inhaled or ingested, causing severe nausea, fainting,
or poisoning.
The safety alert symbol ( ) is used with a signal word
(DANGER, CAUTION, WARNING), a pictorial and/or a safety
message to alert you to hazards. DANGER indicates a hazard
which, if not avoided, will result in death or serious injury.
WARNING indicates a hazard which, if not avoided, could result
in death or serious injury. CAUTION indicates a hazard which, if
not avoided, might result in minor or moderate injury. NOTICE
indicates a situation that could result in equipment damage.
Follow safety messages to avoid or reduce the risk of injury or
death.
• Operate pressure washer ONLY outdoors.
• Keep exhaust gas from entering a confined area through windows,
doors, ventilation intakes, or other openings.
Hazard Symbols and Meanings
• DO NOT start or run engine indoors or in an enclosed area, even if
windows and doors are open.
• Use a respirator or mask whenever there is a chance that vapors
may be inhaled.
• Read all instructions with mask so you are certain the mask will
provide the necessary protection against inhaling harmful vapors.
A
D
G
K
B
E
H
L
C
F
WARNING
Use of pressure washer can create puddles and
slippery surfaces.
Kickback from spray gun can cause you to fall.
• Operate pressure washer from a stable surface.
• The cleaning area should have adequate slopes and drainage to
reduce the possibility of a fall due to slippery surfaces.
• Be extremely careful if you must use the pressure washer from a
ladder, scaffolding, or any other similar location.
• Firmly grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
J
M
A - Explosion
B - Fire
G - Flying Objects
H - Slippery Surface
J - Fall
K - Fluid Injection
L - Moving Parts
M - Read Manual
C - Electric Shock
D - Toxic Fumes
E - Kickback
F - Hot Surface
Safety - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
WARNING
WARNING
Starter cord kickback (rapid retraction) can result in
bodily injury. Kickback will pull hand and arm toward
engine faster than you can let go.
Fuel and its vapors are extremely flammable and
explosive.
Broken bones, fractures, bruises, or sprains could
result.
Fire or explosion can cause severe burns or death.
• NEVER pull starter cord without first relieving spray gun pressure.
• When starting engine, pull cord slowly until resistance is felt and
then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run, always point
spray gun in safe direction and squeeze spray gun trigger to release
high pressure.
• Firmly grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
WHEN ADDING OR DRAINING FUEL
• Turn pressure washer OFF and let it cool at least 2 minutes before
removing fuel cap. Loosen cap slowly to relieve pressure in tank.
• Fill or drain fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting engine.
• Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.
• DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
WARNING
• Ensure spark plug, muffler, fuel cap, and air cleaner are in place.
• DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
• DO NOT tip engine or equipment at angle which causes fuel to spill.
• DO NOT spray flammable liquids.
Contact with muffler area can result in serious
burns.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
WHEN TRANSPORTING OR REPAIRING EQUIPMENT
• Transport/repair with fuel tank EMPTY or with fuel shutoff valve
OFF.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 feet (1.5 m) of clearance on all sides of pressure
washer including overhead.
• Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK
• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public
Property require equipment powered by an internal combustion
engine to have a spark arrester, maintained in effective working
order, complying to USDA Forest service standard 5100-1C or later
revision. In the State of California a spark arrester is required under
section 4442 of the California Public resources code. Other states
may have similar laws.
• Store away from furnaces, stoves, water heaters, clothes dryers, or
other appliances that have pilot light or other ignition source because
they can ignite fuel vapors.
WARNING
Risk of electrocution.
Contact with power source can cause electric shock
or burn.
WARNING
• NEVER spray near power source.
Unintentional sparking can result in fire or electric
shock.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE
WASHER
• Disconnect the spark plug wire from the spark plug and place the
wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
Safety - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
WARNING
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
Risk of eye injury.
Spray can splash back or propel objects.
• Always wear safety goggles when using this equipment or in vicinity
of where equipment is in use.
• Before starting the pressure washer, be sure you are wearing
adequate safety goggles.
• NEVER substitute safety glasses for safety goggles.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
can cause injury.
• DO NOT allow CHILDREN to operate pressure washer.
• NEVER repair high pressure hose. Replace it.
• NEVER repair leaking connections with sealant of any kind. Replace
o-ring or seal.
NOTICE
High pressure spray may damage fragile items including
glass.
• NEVER connect high pressure hose to nozzle extension.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• ALWAYS point spray gun in safe direction and squeeze spray gun
trigger, to release high pressure, every time you stop engine.
• DO NOT point spray gun at glass when using red 0° spray tip.
• NEVER aim spray gun at plants.
NOTICE
• NEVER aim spray gun at people, animals, or plants.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is running.
Improper treatment of pressure washer can damage it and
shorten its life.
• NEVER use a spray gun which does not have a trigger lock or trigger
guard in place and in working order.
• If you have questions about intended use, ask dealer or contact
nearest authorized dealer.
• Always be certain spray gun, nozzles and accessories are correctly
attached.
• NEVER operate units with broken or missing parts, or without
protective housing or covers.
• DO NOT by-pass any safety device on this machine.
• DO NOT tamper with governed speed.
WARNING
• DO NOT operate pressure washer above rated pressure.
• DO NOT modify pressure washer in any way.
• Before starting pressure washer in cold weather, check all parts of
the equipment to be sure ice has not formed there.
Starter and other rotating parts can entangle hands,
hair, clothing, or accessories.
• NEVER move machine by pulling on hoses. Use handle provided on
unit.
• Check fuel system for leaks or signs of deterioration, such as chafed
or spongy hose, loose or missing clamps, or damaged tank or cap.
Correct all defects before operating pressure washer.
• This equipment is designed to be used with Briggs & Stratton Power
Products authorized parts ONLY. If equipment is used with parts that
DO NOT comply with minimum specifications, user assumes all risks
and liabilities.
• NEVER operate pressure washer without protective housing or
covers.
• DO NOT wear loose clothing, jewelry or anything that may be caught
in the starter or other rotating parts.
• Tie up long hair and remove jewelry.
Safety - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Your pressure washer requires some assembly and is ready for
3. Attach handle to main unit.
use after it has been properly serviced with the recommended oil
and fuel.
4. Add oil to engine crankcase.
5. Add fuel to fuel tank.
If you have any problems with the assembly of your pressure
washer, please call the pressure washer helpline at
(888) 228-3068. If calling for assistance, please have the model,
revision, and serial number from the data tag available.
6. Connect high pressure hose to spray gun and pump.
7. Connect water supply to pump.
8. Attach nozzle extension to spray gun.
9. Select/attach quick connect spray tip to nozzle extension.
Unpack Pressure Washer
1. Remove the parts bag, accessories, and inserts included
Attach Handle
1. Place handle (A) onto handle supports (B) connected to
main unit. Make sure holes (C) in handle align with holes on
handle supports.
with pressure washer.
2. Open carton completely by cutting each corner from top to
bottom.
3. Ensure you have all included items prior to assembly.
Items in the carton include:
• Main Unit
A
• Handle
• High Pressure Hose
C
• Spray Gun
• Nozzle Extension with Quick Connect Fitting
• Oil Bottle
B
• Parts Bag (which includes the following):
NOTE: It may be necessary to move the handle supports from
side to side in order to align the handle so it will slide over the
handle supports.
•
•
•
•
•
Operator’s Manual
Engine Operator’s Manual
Owner’s Registration Card
Safety Goggles
2. Insert carriage bolts through holes from outside of unit and
attach a plastic knob from inside of unit. Tighten by hand.
Bag containing 5 Multi-Colored Quick Connect Spray
Tips
•
Handle Fastening Hardware Kit (which includes):
•
•
Carriage Bolts (2)
Plastic Knobs (2)
To prepare your pressure washer for operation, you will need
to perform these tasks:
1. Fill out and send in registration card.
3. Insert multi-colored quick connect spray tips and other
supplied accessories in spaces provided on handle.
2. Verify oil dipstick (A) has been installed into pump.
A
Assembly - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Read this operator’s manual and safety rules before operating your pressure washer.
Compare the illustration with your pressure washer to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
U
T
A
B
C
S
R
D
E
P
F
N
M
G
H
,
L
J
K
A - Spray Tips — Detergent, 0°, 15°, 25° and 40°: for various
high pressure cleaning applications.
N - Throttle Lever — Sets engine in starting mode for recoil
starter.
B - High Pressure Hose — Connect one end to water pump and
P - Engine Switch — Set switch to “On” for recoil starting. Set
switch to “Off” to stop a running engine.
the other end to spray gun.
R - Air Filter — Protects engine by filtering dust and debris out
C - Pressure Control Knob — Varies pressure of high pressure
of intake air.
spray.
S - Fuel Tank — Fill tank with regular unleaded fuel. Always
D - Water Inlet — Connection for garden hose.
leave room for fuel expansion.
E - High Pressure Outlet — Connection for high pressure hose.
T - Nozzle Extension with Quick Connect — Allows you to
F - Warning/Operating Instructions Tag — Identifies hazards
switch between five different spray tips.
and proper procedure to start/stop pressure washer.
U - Spray Gun with Quick Connect — Controls the application of
water onto cleaning surface with trigger device. Includes
trigger lock.
G - Pump — Develops high pressure.
H - Automatic Cool Down System — Cycles water through pump
when water reaches 125°-155°F. Warm water will discharge
from pump onto ground. This system prevents internal pump
damage.
Items Not Shown:
Data Tag (near rear of base plate) — Provides model and serial
number of pressure washer. Please have these readily available if
calling for assistance.
J - Detergent Siphoning Tube/Filter — Use to siphon pressure
washer safe detergent into the low pressure stream.
Oil Fill/Dipstick — Check and add oil here.
K - Choke Lever — Prepares a cold engine for starting.
L - Recoil Starter — Used for starting the engine manually.
M - Fuel Valve — Used to turn fuel supply on and off to engine.
Safety Goggles — Always use the supplied safety goggles when
running your pressure washer.
Operating - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Daily Operating Checklist
WARNING
Review the unit’s assembly to ensure you have performed all of
the following.
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
1. Make sure handle is in place and secure.
2. Check that oil has been added to proper level in the engine
crankcase.
• NEVER connect high pressure hose to nozzle extension.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• Always be certain spray gun, nozzles and accessories are correctly
attached.
3. Add proper fuel to fuel tank.
4. Check for properly tightened hose connections.
5. Check to make sure there are no kinks, cuts, or damage to
high pressure hose.
2. Similarly, attach other end of high pressure hose to high
pressure outlet (A) on pump. Pull down on collar of quick
connect, slide onto pump and let go of collar. Pull on hose
to be sure of tight connection.
6. Provide a proper water supply at an adequate flow.
7. Be sure to read the Safety section before using pressure
washer.
If you have any problems operating your pressure washer, please
call the pressure washer helpline at (888) 228-3068.
Add Engine Oil and Fuel
B
• Place pressure washer on a level surface.
NOTE: Verify provided oil bottle is the correct viscosity for
current ambient temperature.
A
3. Before connecting garden hose to water inlet, inspect inlet
screen (B). Clean screen if it contains debris or have it
replaced if damaged. DO NOT run pressure washer if inlet
screen is damaged.
NOTICE
Any attempt to crank or start the engine before it has been
properly filled with the recommended oil will result in
equipment failure.
4. Run water through your garden hose for 30 seconds to
clean out any debris.
• Refer to engine manual for oil and fuel fill information.
• Damage to equipment resulting from failure to follow this instruction
will void warranty.
IMPORTANT: DO NOT siphon standing water for the water
supply. Use ONLY cold water (less than 100°F).
• Refer to engine operator’s manual and follow oil and fuel
recommendations and instructions.
5. Connect the garden hose (not to exceed 50 feet in length)
to the water inlet. Tighten by hand.
NOTE: Check oil often during engine break–in. Refer to engine
operator’s manual for recommendations.
NOTICE
Damage to pump or water inlet connector will occur if a One Way
Valve (vacuum breaker or check valve) is connected to pump.
Connect Hose and Water Supply to Pump
NOTE: Remove and discard the shipping caps from the pump’s
high pressure outlet and water inlet before attaching hoses.
• There MUST be at least ten feet (3M) of unrestricted garden hose
between the pressure washer inlet and any device, such as a One
Way Valve.
• Damage to equipment caused by attaching a One Way Valve to
pump will void warranty.
NOTICE
DO NOT run the pump without the water supply connected
and turned on.
6. Turn ON the water, press red button on the gun and squeeze
the trigger to purge the pump system of air and impurities.
• Damage to equipment resulting from failure to follow this instruction
will void warranty.
1. Uncoil high pressure hose and attach quick connect end of
hose to base of spray gun. Pull down on collar of quick
connect, slide onto spray gun and let go of collar. Tug on
hose to be sure of tight connection.
WARNING
Risk of eye injury.
Spray can splash back or propel objects.
• Always wear safety goggles when using this equipment or in vicinity
of where equipment is in use.
• Before starting the pressure washer, be sure you are wearing
adequate safety goggles.
• NEVER substitute safety glasses for safety goggles.
Operating - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Pressure Washer Location
How to Start Your Pressure Washer
To start your pressure washer for the first time, follow these
instructions step-by-step. This starting information also applies if
you have let the pressure washer sit idle for at least a day.
Clearances and Air Movement
WARNING
1. Place pressure washer near an outside water source
capable of supplying water at a flow rate greater than
3.8 gallons per minute and no less than 20 PSI at pressure
washer end of garden hose. DO NOT siphon supply water.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
• Keep at least 5 ft. (1.5 m) clearance on all sides of pressure washer
including overhead.
2. Check that high pressure hose is tightly connected to spray
gun and pump. See Assembly section.
3. Make sure unit is in a level position.
Place pressure washer in a well ventilated area, which will allow
for removal of deadly exhaust gas. Do not place pressure washer
where exhaust gas could accumulate and enter inside or be
drawn into a potentially occupied building. Ensure exhaust gas
(A) is kept away from any windows, doors, ventilation intakes, or
other openings that can allow exhaust gas to collect in a confined
area. Prevailing winds and air currents should be taken into
consideration when positioning pressure washer.
4. Connect garden hose to water inlet on pressure washer
pump.
NOTICE
DO NOT run the pump without the water supply connected
and turned on.
• Damage to equipment resulting from failure to follow this instruction
will void warranty.
WARNING
Running engine gives off carbon monoxide, an
odorless, colorless, poison gas.
5. Turn ON water, point gun in a safe direction, press the red
button and squeeze trigger to purge pump system of air
and impurities.
Breathing carbon monoxide can cause headache,
fatigue, dizziness, vomiting, confusion, seizures,
nausea, fainting or death.
6. Attach nozzle extension to spray gun. Tighten by hand.
• Operate pressure washer ONLY outdoors.
• Keep exhaust gas from entering a confined area through windows,
doors, ventilation intakes, or other openings.
• DO NOT start or run engine indoors or in an enclosed area, even if
windows and doors are open.
7. Choose desired spray tip, pull back nozzle extension collar,
insert spray tip and release collar. Tug on spray tip to make
sure it is securely in place. See How to Use Spray Tips.
A
Operating - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
IMPORTANT: Before starting the pressure washer, be sure you
are wearing adequate safety goggles.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
WARNING
Risk of eye injury.
Spray can splash back or propel objects.
• Always wear safety goggles when using this equipment or in vicinity
of where equipment is in use.
• Before starting the pressure washer, be sure you are wearing
adequate safety goggles.
• NEVER substitute safety glasses for safety goggles.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
can cause injury.
• DO NOT allow CHILDREN to operate pressure washer.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• NEVER aim spray gun at people, animals, or plants.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is running.
• NEVER use a spray gun which does not have a trigger lock or trigger
guard in place and in working order.
8. When starting engine, position yourself as recommended
and start engine according to instructions given in engine
operator’s manual. Also see operating instructions tag
located on the pressure washer.
• Always be certain spray gun, nozzles and accessories are correctly
attached.
WARNING
Contact with muffler area can result in serious
burns.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 feet (1.5 m) of clearance on all sides of pressure
washer including overhead.
• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public
Property require equipment powered by an internal combustion
engine to have a spark arrester, maintained in effective working
order, complying to USDA Forest service standard 5100-1C or later
revision. In the State of California a spark arrester is required under
section 4442 of the California Public resources code. Other states
may have similar laws.
WARNING
Starter cord kickback (rapid retraction) can result in
bodily injury. Kickback will pull hand and arm toward
engine faster than you can let go.
Broken bones, fractures, bruises, or sprains could
result.
How to Stop Your Pressure Washer
1. Release spray gun trigger and let engine idle for two
minutes.
2. Turn engine off according to instructions given in engine
operator’s manual.
• NEVER pull starter cord without first relieving spray gun pressure.
3. ALWAYS point spray gun in a safe direction, press red
button and squeeze spray gun trigger to release retained
high water pressure.
• When starting engine, pull cord slowly until resistance is felt and
then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run, always point
spray gun in safe direction, press red button and squeeze spray gun
trigger to release high pressure.
IMPORTANT: Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.
• Firmly grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
Operating - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
3. Pull back on collar, insert new spray tip and release collar.
Tug on spray tip to make sure it is securely in place.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
Usage Tips
• For most effective cleaning, keep spray tip from 8 to
24 inches away from cleaning surface.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
can cause injury.
• If you get spray tip too close, especially using a high
pressure spray tip, you may damage surface being cleaned.
• DO NOT get closer than 6 inches when cleaning tires.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• ALWAYS point spray gun in safe direction, press red button and
squeeze spray gun trigger, to release high pressure, every time you
stop engine.
Cleaning and Applying Detergent
CAUTION
Chemicals can cause bodily injury, and/or property damage.
• NEVER use caustic liquid with pressure washer.
IMPORTANT: Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.
• Use ONLY pressure washer safe detergents/soaps. Follow all
manufacturers instructions.
How to Use Spray Tips
The quick–connect on the nozzle extension allows you to switch
between five different quick connect spray tips. Spray tips can be
changed while pressure washer is running once spray gun
trigger safety lock is engaged. The spray tips vary the spray
pattern as shown below.
To apply detergent, follow these steps:
1. Review use of spray tips.
2. Prepare detergent solution as required by job.
3. Place small filter end of detergent siphoning tube into
detergent container.
WARNING
NOTE: Make sure the filter is fully submerged in detergent while
applying detergent.
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
NOTICE
Contact with the hot muffler can damage detergent siphoning
tube.
• NEVER exchange spray tips without the trigger safety lock engaged
on the spray gun.
• DO NOT twist spray tips while spraying.
• When inserting the filter into a detergent solution bottle, route the
tube so as to keep it from inadvertently contacting the hot muffler.
4. Make sure black spray tip is installed.
Follow these instructions to change spray tips:
NOTE: Detergent cannot be applied with the high pressure spray
tips (White, Green, Yellow or Red).
1. Pull back collar on quick–connect and pull current spray tip
off. Store spray tips in holder provided on the handle.
2. Select desired spray tip:
• For gentle rinse, select white 40° or green 25° spray tip.
• To scour surface, select yellow 15° or red 0° spray tip.
• To apply detergent, select black spray tip.
High
Pressure
Low Pressure
Use to apply
detergent
Black
White
40°
Green
25°
Yellow
15°
Red
0°
Operating - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
5. Make sure garden hose is connected to water inlet. Check
5. Apply a high pressure spray to a small area and then check
surface for damage. If no damage is found, you can assume
it is okay to continue rinsing.
that high pressure hose is connected to spray gun and
pump. Turn on water.
6. Start at top of area to be rinsed, working down with same
overlapping strokes as you used for cleaning.
NOTICE
You must attach all hoses before you start the engine.
• Starting the engine without all the hoses connected and without the
water turned ON will damage the pump.
• Damage to equipment resulting from failure to follow this instruction
will void warranty.
Cleaning Detergent Siphoning Tube
If you used the detergent siphoning tube, you must flush it with
clean water before stopping the engine.
1. Place detergent siphoning tube/filter in a bucket full of clean
water.
6. Start engine following instructions How to Start Your
Pressure Washer.
7. Apply detergent to a dry surface, starting at lower portion of
area to be washed and work upward, using long, even,
overlapping strokes.
2. Remove high pressure spray tip from nozzle extension.
3. Select and install black detergent spray tip following
instructions How to Use Spray Tips.
4. Flush for 1-2 minutes.
8. Allow detergent to "soak in" for 3-5 minutes before washing
and rinsing. Reapply as needed to prevent surface from
drying. DO NOT allow detergent to dry on (prevents
streaking).
5. Shut off engine following instructions How to Stop Pressure
Washer and turn off water supply.
6. ALWAYS point spray gun in a safe direction, press red
button and squeeze spray gun trigger to release retained
high water pressure.
IMPORTANT: You must flush the detergent siphoning system
after each use by placing the filter into a bucket of clean water,
then run the pressure washer in low pressure for 1-2 minutes.
IMPORTANT: Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.
How to Rinse After Use
WARNING
Pressure Washer Rinsing
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
1. Remove black spray tip from nozzle extension.
2. Select and install desired high pressure spray tip following
instructions How to Use Spray Tips.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
can cause injury.
3. Keep spray gun a safe distance from area you plan to spray.
WARNING
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
Kickback from spray gun can cause you to fall.
• ALWAYS point spray gun in safe direction, press red button and
squeeze spray gun trigger, to release high pressure, every time you
stop engine.
• Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure washer from a
ladder, scaffolding, or any other similar location.
Automatic Cool Down System (Thermal Relief)
If you run the engine on your pressure washer for 3-5 minutes
without pressing the trigger on the spray gun, circulating water
in the pump can reach temperatures above 125°F. The system
engages to cool the pump by discharging the warm water onto
the ground.
• Firmly grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
4. Increase (decrease) spray pressure by turning pressure
control knob (A) clockwise (counterclockwise). Use lower
pressure to wash items such as a car or boat. Use higher
pressure to strip paint and degrease driveways.
A
Operating - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
3. Disconnect hose from spray gun and high pressure outlet
After Each Use
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and freeze
pump action. Follow these procedures after every use:
on pump. Drain water from hose, gun, and nozzle
extension. Use a rag to wipe off the hose.
4. Place the spray gun, nozzle extension, spray tips and high
pressure hose on the handle.
1. Flush detergent siphoning tube by placing the filter into a
pail of clean water while running pressure washer in low
pressure mode. Flush for one to two minutes.
5. Empty pump of all pumped liquids by pulling recoil handle
about six times. This should remove most liquid in pump.
6. Store unit in a clean, dry area.
2. Shut off engine, turn off water supply, point gun in a safe
direction, press red button and squeeze trigger to relieve
trapped pressure, and let engine cool.
7. If storing for more than 30 days, see Long Term Storage.
WARNING
WARNING
Fuel and its vapors are extremely flammable and
explosive.
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
Fire or explosion can cause severe burns or death.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
can cause injury.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK
• Store away from furnaces, stoves, water heaters, clothes dryers, or
other appliances that have pilot light or other ignition source because
they can ignite fuel vapors.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• ALWAYS point spray gun in safe direction, press red button and
squeeze spray gun trigger, to release high pressure, every time you
stop engine.
Operating - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS AND SPECIFICATIONS
Service Literature
Product Specifications
Model 3000
If you would like a copy of the Parts Catalog or Technical Manual
Outlet Pressure . . . . . . . . . . . . . . . . . . . . .3000 PSI (206.8 BAR)
Flow Rate . . . . . . . . . . . . . . . . . . . . . . 2.8 GPM (10.6 liters/min)
Water Supply Temperature . . . . . . . .Not to exceed 100°F (38°C)
Pump Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.6 fl. oz.
Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . 84 lbs. (38.1 kg)
for this machine call (888) 228-3068 or contact your local dealer.
Parts
We recommend John Deere quality parts and lubricants, available
at your John Deere dealer.
This product is rated in accordance with PWMA standard PW101
vary due to factors including: the inclusion or exclusion of a
detergent injection system; variations in engine performance; and
environmental conditions.
Part numbers may change - use part numbers listed below when
you order. If a number changes, your dealer will have the latest
number.
When you order parts, your John Deere dealer needs your
machine model and revision number. He may also need your
engine Model and serial number. These are the numbers that you
recorded in Product Identification.
Part Numbers
PumpSaver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6039
Pump Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6033
O-Ring Maintenance Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6048
Water Inlet Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B2384GS
John Deere Turf Gard Engine Oil Bottle . . . . . . . . .Contact Dealer
Fuel Stabilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5041D
(Part numbers are subject to change without notice. Part
numbers may be different outside the U.S.A.)
Replacement Parts and Specifications - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE PRESSURE WASHER
• Use a damp cloth to wipe exterior surfaces clean.
Maintenance
• Use a soft bristle brush to loosen caked on dirt, oil, etc.
• Use a vacuum cleaner to pick up loose dirt and debris.
General Recommendations
Regular maintenance will improve the performance and extend
the life of the pressure washer. See any qualified dealer for
service.
Check and Clean Inlet Screen
Examine the screen on the pump’s water inlet. Clean it if the
screen is clogged or replace it if screen is damaged.
The pressure washer’s warranty does not cover items that have
been subjected to operator abuse or negligence. To receive full
value from the warranty, the operator must maintain the pressure
washer as instructed in this manual and in the engine manual,
including proper storage as detailed in Winter Storage and Long
Term Storage.
NOTE: Should you have questions about replacing components
on your pressure washer, please call (888) 228-3068 for
assistance.
Check High Pressure Hose
The high pressure hose can develop leaks from wear, kinking, or
abuse. Inspect the hose each time before using it. Check for cuts,
leaks, abrasions or bulging of cover, damage or movement of
couplings. If any of these conditions exist, replace the hose
immediately.
WARNING
• Some adjustments will need to be made periodically to
properly maintain your pressure washer. Check the spray
gun and nozzle extension assembly for wear.
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
• All maintenance in this manual and the engine operator’s
manual should be made at least once each season.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST exceed maximum pressure rating of
unit.
• Once a year you should clean or replace the spark plug,
clean or replace the air filter. A new spark plug and clean air
filter assure proper fuel-air mixture and help your engine
run better and last longer. Please refer to your engine
operator’s manual for more details.
Check Detergent Siphoning Tube
Examine the filter on the detergent tube and clean if clogged. The
tube should fit tightly on the barbed fitting. Examine the tube for
leaks or tears. Replace the filter or tube if either is damaged.
Pressure Washer Maintenance
Clean Debris
Check Gun and Nozzle Extension
Daily or before use, clean accumulated debris from cleaning
system. Keep linkage, spring and controls clean. Keep area
around and behind muffler free from any combustible debris.
Inspect cooling air slots and openings on the pressure washer.
These openings must be kept clean and unobstructed.
Examine the hose connection to the spray gun and make sure it
is secure. Test the trigger by pressing the red button and making
sure the trigger “springs back” into place when you release it.
You should not be able to press the trigger without pressing the
red button. Replace spray gun immediately if it fails any of these
tests.
Cleaning system parts should be kept clean to reduce the risk of
overheating and ignition of accumulated debris.
NOTICE
Improper treatment of pressure washer can damage it and
shorten its life.
• DO NOT insert any objects through cooling slots.
Service Pressure Washer - 14
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE PRESSURE WASHER
Nozzle Maintenance
O-Ring Maintenance
A pulsing sensation felt while squeezing the spray gun trigger
may be caused by excessive pump pressure. The principal cause
of excessive pump pressure is a spray tip clogged or restricted
with foreign materials, such as dirt, etc. To correct the problem,
immediately clean the spray tip following these instructions:
Purchase an O-Ring/Maintenance Kit, Model 6048, by contacting
the nearest authorized dealer. It is not included with the pressure
washer. This kit includes replacement o-rings, rubber washer and
water inlet filter. Refer to the instruction sheet provided in the kit
to service your unit’s o-rings.
1. Shut off engine and turn off water supply.
WARNING
2. ALWAYS point spray gun in a safe direction, press red
button and squeeze spray gun trigger to release retained
high water pressure.
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
WARNING
• NEVER repair leaking connections with sealant of any kind. Replace
o-ring or seal.
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
Pump Oil Maintenance
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
can cause injury.
Changing Pump Oil
Change oil after first 50 hours of operation and then every
200 hours or 3 months, whichever occurs first.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
NOTE: When changing pump oil, use only high quality
nondetergent 30 weight oil. Use no special additives.
• ALWAYS point spray gun in safe direction, press red button and
squeeze spray gun trigger, to release high pressure, every time you
stop engine.
Change pump oil as follows:
1. Clean area around brass oil drain plug at bottom of pump.
3. Remove spray tip from end of nozzle extension.
2. Remove oil drain plug. Drain oil completely into an
approved container.
4. Use a small paper clip to free any foreign material clogging
or restricting spray tip (A).
3. When oil has completely drained, install oil drain plug and
tighten firmly.
4. Clean area around pump oil dipstick. Remove dipstick and
fill pump with recommended oil (approximately 9.6 oz.) to
“Full” mark on dipstick.
A
5. Remove nozzle extension from spray gun.
5. Install pump oil dipstick.
6. Wipe up any spilled oil.
6. Using a garden hose, remove additional debris by back
flushing water through nozzle extension. Back flush between
30 to 60 seconds.
Engine Maintenance
See the engine operator’s manual for instructions on how to
properly maintain the engine.
CAUTION
Avoid prolonged or repeated skin contact with used motor oil.
7. Reinstall spray tip into nozzle extension.
8. Reconnect nozzle extension to spray gun.
• Used motor oil has been shown to cause skin cancer in certain
laboratory animals.
• Thoroughly wash exposed areas with soap and water.
9. Make sure garden hose is connected to water inlet. Check
that high pressure hose is connected to spray gun and
pump. Turn on water.
KEEP OUT OF REACH OF CHILDREN. DON’T POLLUTE.
CONSERVE RESOURCES. RETURN USED OIL TO
COLLECTION CENTERS.
10. Start engine following instructions How to Start Your
Pressure Washer.
11. Test pressure washer by operating with each quick connect
spray tip.
Service Pressure Washer - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Using Troubleshooting Chart
If you are experiencing a problem that is not listed in this chart,
see your authorized dealer for service.
When you have checked all the possible cause listed and you are
still experiencing the problem, see your authorized dealer.
Troubleshooting Chart
Problem
Cause
Correction
1. Low pressure spray tip installed.
2. Water inlet is blocked.
1. Replace with high pressure spray tip.
2. Clear inlet.
3. Inadequate water supply.
3. Provide adequate water flow.
4. Straighten inlet hose, patch leak.
5. Check and clean inlet hose screen.
6. Provide cooler water supply.
4. Inlet hose is kinked or leaking.
5. Clogged inlet hose screen.
6. Water supply is over 100°F (38°C).
Pump has following problems: failure to
produce pressure, erratic pressure,
chattering, loss of pressure, low water
volume.
7. High pressure hose is blocked or leaks. 7. Clear blocks in outlet hose.
8. Spray gun leaks.
9. Spray tip is obstructed.
10. Pump is faulty.
8. Replace spray gun.
9. Clean spray tip.
10. Contact local service facility.
1. Detergent siphoning tube is not
submerged.
1. Insert detergent siphoning tube into
detergent.
Detergent fails to mix with spray.
2. Detergent siphoning tube/filter is
clogged or cracked.
2. Clean or replace filter/detergent
siphoning tube.
3. High pressure spray tip installed.
3. Replace with low pressure spray tip.
Engine speed is too slow.
Move throttle control to FAST position. If
engine still "bogs down", contact local
service facility.
Engine runs good at no-load but "bogs"
when load is added.
1. Low oil level.
2. Dirty air cleaner.
3. Out of fuel.
1. Fill crankcase to proper level.
2. Clean or replace air cleaner.
3. Fill fuel tank.
4. Stale fuel.
4. Drain fuel tank; fill with fresh fuel.
Engine will not start; or starts and runs
rough.
5. Spark plug wire not connected to spark 5. Connect wire to spark plug.
plug.
6. Bad spark plug.
6. Replace spark plug.
7. Water in fuel.
7. Drain fuel tank; fill with fresh fuel.
8. Contact local service facility.
8. Excessively rich fuel mixture.
Out of fuel.
Fill fuel tank.
Engine shuts down during operation.
Engine lacks power.
Dirty air filter.
Replace air filter.
Troubleshooting - 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
Storing the Engine
Winter Storage
See the engine operator’s manual for instructions on how to
properly prepare the engine for storage.
NOTICE
You must protect your unit from freezing temperatures.
Protecting the Pump
• Failure to do so will permanently damage your pump and render
your unit inoperable.
• Freeze damage is not covered under warranty.
To protect the pump from damage caused by mineral deposits or
freezing, use PumpSaver, Model 6039, to treat pump. This
prevents freeze damage and lubricates pistons and seals.
To protect the unit from freezing temperatures:
1. Follow steps 1-5 in the previous section After Each Use.
2. Use pump saver, Model 6039, to treat pump. This
NOTICE
You must protect your unit from freezing temperatures.
minimizes freeze damage and lubricates pistons and seals.
• Failure to do so will permanently damage your pump and render
your unit inoperable.
• Freeze damage is not covered under warranty.
3. If pump saver is not available, connect a 3 ft. section of
garden hose to water inlet adapter. Pour RV-antifreeze
(antifreeze without alcohol) into hose. Pull recoil handle
twice. Disconnect 3 ft. hose.
NOTE: PumpSaver is available as an optional accessory. It is not
included with the pressure washer. Contact the nearest
authorized dealer to purchase PumpSaver.
4. Store unit in a clean, dry area.
To use PumpSaver, make sure the pressure washer is turned off
and disconnected from supply water. Read and follow all
instructions and warnings given on the PumpSaver container.
Long Term Storage
If you do not plan to use the pressure washer for more than
30 days, you must prepare the engine and pump for long term
storage.
Other Storage Tips
1. DO NOT store fuel from one season to another unless it has
Protect Fuel System
been treated as described in Protect Fuel System.
Fuel Additive:
2. Replace fuel container if it starts to rust. Rust and/or dirt in
fuel can cause problems if it’s used with this unit.
Fuel will become stale when stored over 30 days. Stale fuel
causes acids and gum deposits to form in the fuel system or on
essential carburetor parts. Prior to storage, if gasoline has not
been treated with a fuel stabilizer, it must be drained from the
engine into an approved container. Then run engine until it stops
from lack of fuel.
3. Cover unit with a suitable protective cover that does not
retain moisture.
WARNING
When fuel stabilizers are used according to their instructions, there
is no need to drain the gasoline from the engine prior to storage.
Use Briggs & Stratton FRESH START™ fuel stabilizer. Run the
engine for a short time to circulate stabilizer throughout the fuel
system. Engine and fuel can then be stored up to 24 months.
Storage covers can be flammable.
• DO NOT place a storage cover over a hot pressure washer.
• Let equipment cool for a sufficient time before placing the cover on
the equipment.
If gasoline is drained, the use of a fuel stabilizer in the storage
container is still recommended to maintain freshness.
4. Store unit in a clean and dry area.
Storage - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
JOHN DEERE® PRESSURE WASHER OWNER WARRANTY POLICY
Effective December 1, 2006 replaces all undated Warranties and all Warranties dated before December 1, 2006
LIMITED WARRANTY
John Deere® and the leaping deer logo are registered trademarks of Deere & Co. and are used under license to Briggs & Stratton Power Products.
Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the pressure washer that is defective in material or
workmanship or both. Read Other Exclusions below. Transportation charges on product submitted for repair or replacement under this warranty must
be borne by purchaser. This warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest
Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE
EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some
states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state or country to country.
WARRANTY PERIOD
Consumer Use
2 years
90 days
Commercial Use
*
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated above.
“Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other uses, including use for commercial,
income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for purposes of
this warranty.
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE
RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING
DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
ABOUT YOUR WARRANTY
We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty
repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if
equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the
warranty is void if the manufacturing date or the serial number on the pressure washer or engine has been removed or the equipment has been altered or
modified. During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be
defective under normal use and service. This warranty will not cover the following repairs and equipment:
•
•
Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty also does not
cover normal maintenance such as air filters, adjustments, fuel system cleaning and obstruction (due to chemical, lime, dirt, and so forth).
Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized installation or
alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as, in our judgment,
to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as air filters, adjustments, fuel system
cleaning and obstruction (due to chemical, lime, dirt, and so forth).
•
Other Exclusions: This warranty excludes wear items such as quick couplers, seals, o-rings, pumps that have been run without water supplied or
damage or malfunctions resulting from accidents, abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration.
Accessory parts, such as guns, hoses, nozzle extensions (wands), and nozzles, are excluded from the product warranty. This warranty excludes used,
reconditioned, and demonstration equipment and failures due to acts of God and other force majeure events beyond the manufacturers control.
201605E, Rev. -, 1/10/2007
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
JEFFERSON, WI, USA
Warranty - 18
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING QUALITY SERVICE
John Deere Quality Continues with Quality Service
John Deere provides a process to handle your questions or
problems, should they arise, to ensure that product quality
continues with your John Deere dealer’s parts and service
support.
Follow the steps below to get answers to any questions you may
have about your product.
1. Refer to your machine and engine operator manuals.
2. Contact your nearest authorized dealer with unanswered
questions.
3. In North America or Canada, call the John Deere Customer
Service Center.
•
Call (888) 228-3068 and provide product serial number
and model number.
Getting Quality Service - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE RECORD
Model No. 020298 (3000 PSI Pressure Washer) Manual No. 201998GS Revision A (02/14/2007)
Service Record
Download from Www.Somanuals.com. All Manuals Search And Download.
|