OWNER’S MANUAL
AFS-2000 Air Filtration
JET EQUIPMENT & TOOLS, INC.
A WMH Company
P.O. BOX 1349
Auburn, WA 98071-1349
e-mail [email protected]
253-351-6000
Fax 800-274-6840
M-708615 5/00
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
1. FOR YOUR OWN SAFETY, READ
INSTRUCTION MANUAL BEFORE
OPERATING THE TOOL. Learn the tool’s
application and limitations as well as the
specific hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working
order.
3. ALWAYS WEAR EYE PROTECTION.
4. GROUND ALL TOOLS. If tool is equipped
with three prong plug, it should be plugged
into a three-hole electrical receptacle. If an
adapter is used to accommodate a two
prong receptacle, the adapter lug must be
attached to a know ground. Never remove
the third prong.
16. DISCONNECT TOOLS before servicing
and when filters.
17. USE RECOMMENDED ACCESSORIES.
The use of accessories and attachments not
recommended by manufacturer may cause
hazards or risk of injury to persons.
18. AVOID ACCIDENTAL STARTING. Make
sure switch is in “OFF” position before
plugging in power cord.
19. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the fan
blade is accidentally contacted.
20. CHECK DAMAGED PARTS. Before further
use of the tool, a guard or other part that is
damaged should be carefully checked to
ensure that it will operate properly and
perform its intended function-check for
alignment of moving parts, binding of
moving parts, breakage of parts, mounting,
and any other conditions that may affect its
operation. A guard or other part that is
damaged should be properly repaired or
replaced.
21. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER OFF.
Don’t leave tool until it comes to a complete
stop.
22. DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of
drugs, alcohol or any medication.
5. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
6. DON’T USE IN DANGEROUS
ENVIRONMENT. Don’t use power tools in
damp or wet locations, or expose them to
rain. Keep work area well-lighted.
7. KEEP CHILDREN AND VISITORS AWAY.
All children and visitors should be kept a
safe distance from work area.
8. MAKE WORKSHOP CHILDPROOF. Use
padlocks, master switches, or remove
starter keys.
9. DON’T FORCE TOOL. It will do the job
better and be safer at the rate for which it
was designed.
10. USE RIGHT TOOL. Don’t force tool or
attachment to do a job for which it was not
designed.
23. MAKE SURE TOOL IS DICONNECTED
FROM POWER SUPPLY while motor is
being mounted, connected or reconnected.
24. WARNING: Some dust created by power
sanding, sawing, grinding, drilling and other
construction activities contains chemicals
known to cause cancer, birth defects or
other reproductive harm. Some examples of
these chemicals are:
11. WEAR PROPER APPAREL. No loose
clothing, gloves, neckties, rings, bracelets,
or other jewelry to get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long
hair.
12. ALWAYS USE SAFETY GLASSES. Wear
safety glasses (must comply with ANSI
Z87.1). Everyday eyeglasses only have
impact resistant lenses; they are not safety
glasses. Also use face or dust mask if
cutting operation is dusty.
•
•
Lead from lead based paint
crystalline silica from bricks and cement
and other masonry products, and
•
arsenic and chromium from chemically-
treated lumber.
25. Your risk from those exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are
specifically designed to filter out microscopic
particles
13. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than
using your hands and frees both hands to
operate tool.
14. DON’T OVERREACH. Keep proper footing
and balance at all times.
15. MAINTAIN TOOLS IN TOP CONDITION.
Keep tools sharp and clean for best and
safest performance. Follow instructions for
lubricating and changing accessories.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Requirements
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The
conductor, with insulation having an outer surface that is green with or without yellow stripes, is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is properly grounded.
Use only three wire extension cords that have three-prong grounding plugs and three-pole receptacles
that accept the tool’s plug.*
Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet that looks the one illustrated in Figure A below.
The tool has a grounding plug that looks like the grounding plug as illustrated in Figure A below. A
temporary adapter, which locks like the adapter as illustrated in Figures B and C below, may be used to
connect this plug to a two-pole receptacle, as shown in Figure B if a properly grounded outlet is not
available.** The temporary adapter should only be used until a properly grounded outlet can be installed
by a qualified electrician. The green colored rigid ear or tab, extending from the adapter, must be
connected to a permanent ground such as a properly grounded outlet box.
* Canadian electrical codes require extension cords to be certified SJT type or better.
** Use of an adapter in Canada is not acceptable.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
AFS-2000
Stock Number................................................................................................................................ 708615
Outer Filter .................................................................................................................................5 Microns
Inner Filter ................................................................................................................................... 1 Micron
Overall Dimensions (LxWxH/in)...............................................................................................44 x 24 x 20
Sound Rating @ 3ft ....................................................................................................High Speed 73.8 dB
............................................................................................................................. Medium Speed 62.0 dB
....................................................................................................................................Low Speed 59.1 dB
Air Flow ................................................................................................................. High Speed 1700 CFM
......................................................................................................................... Medium Speed 1200 CFM
................................................................................................................................. Low Speed 800 CFM
Motor................................................................................................................. 1/3 HP, 115V, 115V Only
Shipping Size (LxWxH/in) .......................................................................................................46 x 26 x 22
Net Weight.....................................................................................................................................110 lbs.
Shipping Weight.............................................................................................................................121 lbs.
Table of Contents
Page
Warranty..................................................................................................................................................2
Warnings.................................................................................................................................................3
Electrical Requirements...........................................................................................................................4
Specifications ..........................................................................................................................................5
Table Of Contents....................................................................................................................................5
For Your Own Safety ...............................................................................................................................5
Contents of Shipping Carton ....................................................................................................................6
Tools Required for Assembly ...................................................................................................................6
Assembly.................................................................................................................................................6
Controls and Features .............................................................................................................................7
Changing Filters....................................................................................................................................7-8
Breakdown ..............................................................................................................................................9
Parts List ..........................................................................................................................................10-11
Wiring Diagram......................................................................................................................................11
FOR YOUR OWN SAFETY
1. Read and understand instruction manual before installing or operating air cleaner.
2. To reduce the risk of injury disconnect the air cleaner from the power source (unplug) before servicing
or changing filters.
3. If ceiling mounted, bottom of air cleaner must be at least 7 feet above the floor.
4. If ceiling mounted, mounts must be anchored to building structure which will support a minimum of at
least 220 pounds. Never mount to surfaces such as dry wall or false ceiling grids, etc.
5. To reduce the risk of electrical shock, do not expose air cleaner to water or rain.
6. Never duct a machine directly into the air cleaner.
7. To avoid a potentially dangerous situation, do not use this equipment to filter volatile fumes or smoke.
This air cleaner is designed and intended for the filtration of air borne wood dust only. It is neither
designed or intended for any other purpose whatsoever.
8. Failure to comply may result in serious injury and / or property damage.
The specifications in this manual are given as general information and are not binding. JET Equipment
& Tools reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of Shipping Carton
1. Air Filtration Unit
1. Remote Control
2. AAA Batteries
4. Eye Bolts, Washers & Hex Nuts
1. Manual and Warranty Card
Tools Required for Assembly
10 mm Wrench
•
The air filtration unit does not require much
assembly. You should take into
consideration how and where you will place
this unit.
•
•
•
This unit will work best if it is located away
from corners, and heating/cooling vents.
If using on sawhorses the air filtration unit
should be clamped in place.
This unit is specifically designed to circulate
and filter non-metallic dust, which is
generated throughout the work area.
Assembly
CAUTION!
Mounts must be anchored to building
structure, which will support a minimum of
at least 220 pounds. Never mount to
surfaces such as dry wall or false ceiling
grids, etc.
1. Remove all packing from inside of the
unit by opening the side panel.
2. Make sure the hex nut (A, Fig. 1) is threaded
all the way up the eyebolt (B, Fig. 1).
3. Place a flat washer (C, Fig.1) on the eye
bolt. Screw the eye bolt into the cabinet and
tighten hex nut against the cabinet top. You
will need to hold the eyebolt so it does not
spin while tightening the lock nut.
4. Repeat steps for remaining three eyebolts.
Note: Make sure chain and ceiling hooks are
properly rated for hanging this unit. Hang unit
with a seven-foot clearance from the floor.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Features
Remote Control:
Time button (A, Fig. 2) controls the three
different settings.
2H will light up on the back of the unit with one
press of the time button. The air filtration
system will operate for 2 hours then shut off.
4H will light up on the back of the unit by
pressing the time button twice. The air filtration
system will operate for 4 hours then shut off.
8H will light up on the back of the unit by
pressing the time button three times. The air
filtration system will operate for 8 hours then
shut off.
Speed button (B, Fig. 2) controls the three
different settings, Low, Medium and High. There
is also a manual button (C, Fig. 2) on the
backside of this unit which controls the speed.
On/Off button (D, Fig. 2) turns the unit on and
off. There is also a manual on/off button (E, Fig.
2) on the backside of the unit. Pressing this
button will turn the machine on Low.
Overload reset switch (F, Fig. 2) will pop in the
case of overload. Wait 3-5 minutes and press
the reset switch.
Changing the Filters
WARNING
To reduce the risk of injury disconnect the
air filtration unit from the power source
(unplug) before servicing or changing
filters. Failure to comply may cause
serious injury!
Outer Filter: remove from the side of the
cabinet (A, Fig. 3). This filter should be
replaced depending on the usage and
environment of your shop.
JET sells
a
replacement metal framed filter that can be
blown out or washed, (stock # 708724 shown in
figure 3).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Inner Filter: you must remove the two bolts
(A, Fig. 4) that hold the cover in place. Remove
the cover. Remove the inner filter (A, Fig. 5)
from the side of the cabinet. Replace the cover
and four bolts.
Accessory Filter: an additional charcoal
filter, or electrostatic filter can be added to this
empty slot (B, Fig.5). Replace the cover and
four bolts
Diffuser: the diffuser (A, Fig. 6) should not
need any maintenance. You can remove from
the side of the cabinet.
The filters should be replaced depending on
the amount of usage and the environment of
your shop. Clogged filters will reduce the
amount of air circulation.
Order replacement filters using the below listed
stock numbers.
708722 Outer Filter (cardboard frame)
708724 Outer Filter (metal frame washable)
330025 Air Diffuser
708723 Inner Filter
708721 Charcoal Filter
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List for the AFS-2000 Air Filtration
Description
Index Part
No. No.
Size
Qty.
1..........330001............................. Fan Blade...................................................... .................................1
2..........330002............................. Fan Housing.................................................. .................................1
3..........330003............................. Air Guide Plate .............................................. .................................2
4..........330004............................. Flange........................................................... .................................1
5..........330005............................. Spacer........................................................... .................................4
6..........330006............................. Sleeve........................................................... .................................4
7..........330040............................. Box Plate....................................................... .................................1
............LM000280........................ JET Label...................................................... .................................2
............LM000351........................ Warning Label ............................................... .................................1
8..........AB330010 ........................ Fan Plate....................................................... .................................1
9..........AB330041 ........................ Frame............................................................ .................................1
10........AB330042 ........................ Frame............................................................ .................................1
11........330011............................. Air Filter Support............................................ .................................2
12........330012............................. Air Box Support ............................................. .................................2
13........330017............................. Fan Support Bar (1)....................................... .................................1
14........330018............................. Fan Support Bar (2)....................................... .................................1
15........330019............................. Side Cover .................................................... .................................1
16........330020............................. Fan Cover ..................................................... .................................1
17........708722............................. Outer Filter (cardboard frame)........................ 24”x20”x2” ................1
............708724............................. Outer Filter (metal frame: washable) .............. 24”x20”x2” ..................
18........330025............................. Air Diffuser .................................................... 24”x20”x1” ................1
19........330026............................. Motor............................................................. .................................1
............CA003000........................ Capacitor (not shown).................................... .................................1
20........708723............................. Inner Filter..................................................... 24”x20”x12”x8B ........1
21........OO1023 ........................... Eye Bolt......................................................... .................................4
22........NH061000........................ Nut ................................................................ M6............................4
23........10042............................... Nut ................................................................ .................................6
24........SR060600........................ Hex Socket Bolt............................................. M6x30 ......................4
25........WF061620 ....................... Washer.......................................................... M6x16 ......................4
26........SR089400........................ Hex Socket Bolt............................................. M8x16 ......................1
27........SF069200 ........................ Pan Head Bolt W/Flange ............................... M6x8 ......................22
28........ST049200 ........................ Tapping Screw .............................................. M4x8 ......................28
29........BR000062........................ Rivet.............................................................. .................................4
30........SH089400........................ Hex Head Bolt ............................................... M8x16 ......................6
31........WF081818 ....................... Washer.......................................................... M8x18 ......................6
32........NF050800 ........................ Nut ................................................................ M5............................4
33........OO1033 ........................... Switch Wire W/Terminal................................. 18AWG.....................1
34........NH050800........................ Nut ................................................................ M5............................2
35........WE050000 ....................... Star Washer (External) .................................. M5............................2
36........OO1022 ........................... Switch Plate................................................... .................................1
37........SP059300 ........................ Pan Head Bolt ............................................... M5x12 ......................1
38........IC001015 ......................... Cord .............................................................. 18AWGx3C ..............1
39........998623............................. Strain Relief................................................... .................................1
40........330039............................. 8A Thermos Switch........................................ .................................1
41........ST049200 ........................ Tapping Screw .............................................. M4x8 ........................4
42........SN490200........................ Counter Sunk Bolt ......................................... 1/8”x1/4”...................3
43........330043............................. PC Board....................................................... .................................1
44........LM000354........................ Circuit Board Label ........................................ .................................1
45........990638............................. Wiring Nut ..................................................... P2.............................1
46........708711............................. Remote Control ............................................. .................................1
47........LM000279........................ Remote Label................................................ .................................1
50........330030............................. Bolt................................................................ .................................2
51........WS080000 ....................... Spring Washer............................................... M8............................6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
52........BR000031........................ Rivet.............................................................. .................................2
53........AB001008 ........................ Door Clip Set................................................. .................................1
54........WF061620 ....................... Flat Washer................................................... M6............................4
55........330046............................. Pad ............................................................... .................................2
Optional Replacement Filters:
............708722............................. Outer Filter (cardboard frame)........................ 24”x20”x2” ................1
............708724............................. Outer Filter (metal frame: washable) .............. 24”x20”x2” ..................
............330025............................. Air Diffuser .................................................... 24”x20”x1” ................1
............708723............................. Inner Filter..................................................... 24”x20”x12”x8B ........1
............708721............................. Charcoal Filter............................................... 24x20x2....................1
Wiring Diagram
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|