Installation and Operating Instructions for
elmira stove works
electric ranges (models 1850 & 1855)
Gas/electric Combos (models 1865, 1870 & 1875)
Gas ranges(models 1860 & 1867)
Your porcelain stove top has been
coated with Turtle Wax for added
protection and ease of cleaning.
We recommend that it be rewaxed
every 3 months or as needed.
Install gas line and electric
receptacle behind stove six inches
off floor in center of opening.
Attention: Oven Bottom Finish
Do not line the oven bottom
with any type of liners, foil or
cookware. Do not cook on the oven
bottom. Permanent damage to
the oven bottom will result!
Exhaust fan must be operating while back burners
are on and/or oven is self cleaning.
Note: thermometer on oven door is decorative only; it is not functional.
Thank you for purchasing an Elmira Stove Works range.
You have purchased a quality, world-class product.
Years of engineering experience have gone into its manufacturing.
To ensure that you will enjoy many years of trouble-free operation,
we have developed this User Guide.
It is full of valuable information on how to operate and maintain
your range properly and safely. Please read it carefully.
1604–9
Download from Www.Somanuals.com. All Manuals Search And Download.
gas range warning
• Do not try to light any appliance.
warning: if the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or death.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. follow the gas supplier’s
instructions.
– Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
• If you cannot reach your gas supplier, call the fire
department.
– installation and service must be performed by a
qualified installer, service agency or the gas supplier.
– what to Do if you smell gas.
Before using your range reaD this Book carefully
if you received a damaged range:
Immediately contact the dealer that sold you the range.
Before you request service:
Check Troubleshooting. It lists causes of minor operating problems that you may be able to correct yourself.
taBle of contents
Safety InStructIonS – All Models........................... 4
amperage requIrementS – BTU’s......................... 5
Safety InStructIonS – Gas ...................................... 6
InStallIng your range .......................................... 7
InStallatIon of range Into cabInetS ............. 7
InStallIng your exhauSt hood.......................... 8
Smooth top electrIc cooktop .......................... 9
cookIng tIpS............................................................. 24
Convection Cooking Tips.......................................... 24
Broiling...................................................................... 20
Convection Broiling .................................................. 27
General Broiling Tips................................................ 27
Convection Roasting Rack ........................................ 27
Air Circulation........................................................... 27
Oven Rack Positions.................................................. 28
For Proper Cooking,
SelectIon of potS & panS
for electrIc top................................................ 10
Follow These Guidelines........................................... 28
Rack Placement for Specific Foods........................... 28
Using Aluminum Foil in the Oven ............................ 28
grIddle – Optional..................................................... 10
gaS cooktop............................................................. 13
gaS burner cleanIng ........................................... 13
oven vent - gaS....................................................... 14
gaS Supply SyStem ................................................. 14
gaS range converSIon to lp............................ 15
gaS adjuStIng for proper flame .................... 16
electronIc oven control.................................. 18
Important Oven Control Information ........................ 18
Setting the Clock ....................................................... 19
Using the Minute Timer ............................................ 19
Conversion from Fahrenheit to Celsius..................... 19
Oven Control Recalibration....................................... 19
Non Timed Bake........................................................ 19
Automatic Timed Bake.................................................. 20
Delayed Bake............................................................. 20
Broil and Vari-Broil................................................... 20
Self Cleaning Oven.................................................... 20
Safety Features .......................................................... 21
Control Panel Lock.................................................... 21
Cabinet Light Switch................................................. 21
Exhaust Fan Switch ................................................... 21
Stay Hot Food Warmer.............................................. 21
oven Self-cleanIng cycle ................................ 21
How the Self-Cleaning Cycle Works ........................ 21
Before You Start........................................................ 22
For Best Cleaning Results ......................................... 22
Automatic Door Lock................................................ 22
maIntenance & mInor repaIrS......................... 22
Removing Oven Door................................................ 22
Lubrication & Minor Service .................................... 23
ServIce ........................................................................ 23
gaS troubleShootIng ........................................... 24
roaStIng chart....................................................... 25
bakIng chart........................................................... 26
broIlIng chart........................................................ 26
convectIon cookIng ............................................. 29
WIrIng dIagram ...................................................... 33
cleanIng guIde........................................................ 34
troubleShootIng .................................................... 35
partS of your range................................... 36 & 37
Warranty .................................................................. 40
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Allow elements and burner surfaces to cool before cleaning.
If a wet sponge or cloth is used to wipe spills on a hot
cooking area, be careful to avoid steam burn. Some cleaners
can produce noxious fumes if applied to a hot surface.
safety instructions
(all models)
Important! Save these instructions for the local
Loose clothing of flammable material (pot holders) could
ignite if brought in contact with hot burners and may
cause severe burns.
inspector’s use.
WarnIng! Prior to installing this appliance, read
the Safety Instructions as they relate to Installation on
pages 3 through 7 of this manual. Failure to follow these
instructions could result in serious electric hazard, risk of
fire, and/or personal injury.
Moist or damp pot holders on hot surfaces may result in
burns from steam. Do not let pot holders touch hot heating
elements. Do not use towels or other bulky cloths as pot
holders.
models 1850, 1855, 1865, 1870 & 1875 are equipped
with a 240 volt, standard range power cord & plug.
see page 4 for amp ratings of each model.
Cooktop temperatures increase with the number of
elements on. With three or four elements turned on,
surface temperatures are high. Exercise care when
touching the cooktop.
models 1860 & 1867 come with a 120 volt, 5 amp power
cord & plug.
Use this appliance for its intended use, as described in this
manual.
fire
Keep the hood and grease filters clean to maintain good
venting and to avoid grease fires.
Never use your appliance for warming or heating the
room.
Do not let cooking grease or other flammable materials
accumulate in or near the range.
Do not assume that you know how to operate all parts of
the range. Some features may work differently from those
of your previous range.
grease
Grease is flammable and should be handled carefully.
Avoid letting grease deposits collect around the range in
vent fans. Don’t leave cans of drippings sit around the
range; refrigerate or dispose of promptly. Let quantities
of hot fat (a pan of deep fat for example) cool before
attempting to move or handle it. Grease fires can often
be extinguished by quickly putting on the pan lid or by
covering with baking soda. Do not attempt to extinguish
with water because this will spread the fire.
Do not climb, stand or hang on the door or range top.
This can damage the range or tip it over, causing severe
personal injury.
children
Do not leave children alone in the area where your range
is in use. They should never be allowed to stand or sit on
any part of this appliance.
Instruct your small children that the range is not a toy and
could hurt them. As your children grow up, teach them the
proper and safe use of the range.
never pick up a flaming pan.
oven
Children must be taught not to use the oven door as a
stepping stool to reach the cabinet above, as it may result
in an injury.
Stand away from range when opening the oven door. Hot
air or steam which escapes can cause burns.
Do not heat unopened food containers in the oven.
Pressure could build up and the container could burst,
causing injury or damage to the range.
caution
Do not store items of interest to children on cabinet
above the range or on the back of the cooking surface.
children climbing to reach items could be seriously
injured.
Keep oven vent ducts unobstructed.
Keep oven free from grease build up.
Place oven rack in desired position while oven is cool.
If rack must be handled when hot, do not let pot holder
touch heating elements in the oven.
When cleaning cycle is on, the oven door and cooking
surface will be hot. Keep children away from the range as
a safety precaution.
Pull out oven rack to the rack stop to reduce chance of
burns from touching hot surfaces of the door and oven.
storage
When using cooking or roasting bags in oven, follow the
manufacturer’s directions.
Do not store gasoline, flammable vapors or materials, etc.,
in the oven, under or around the appliance area.
Do not use your oven to dry newspapers.
hot surface
Exercise caution. Surfaces may be hot enough to burn.
Electric elements may be hot even when they appear dark
in color.
aluminum foil
Do not use aluminum foil near the broil element. This
could cause damage to the elements.
Do not operate surface burners without utensils in place.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Plastics
service
Do not repair or service any part of the range unless
specifically recommended in this manual. All other
servicing should be referred to a qualified technician.
Disconnect the range from wall receptacle (or fuse) before
performing service.
All plastics are vulnerable to heat, although some will
withstand higher temperatures than others. Keep all
plastics away from parts of the range which may become
slightly more than warm when the range is in operation.
self-cleaning oven
The door gasket is essential for a good seal. Care should
be taken not to rub, damage or move the gasket.
safety
Your range, like many other household items, is heavy
and can settle into soft floor coverings such as cushion
vinyl or carpeting. When moving the range on this type of
flooring use care.
If your range must stand beside a refrigerator, allow at
least 2” between the two appliances for air circulation.
The heat from the range may affect refrigerator
performance.
Do not use oven cleaners on your oven prior to self-
cleaning. Damage may occur to oven finish at high
temperatures. Remove aluminum or plastic utensils, food or
combustible materials from oven and cooktop before self-
cleaning.
(See Self-Cleaning – Page 17)
NOTE: Oven cleaner will not harm porcelain oven but
should not be used in conjunction with self-cleaning.
Make sure that all the packing materials, including tape
on elements and packing material above and below oven
elements, have been removed and that all controls are in
the off position before plugging in the power cord.
surface cooking
Use proper pan size. Select pans large enough to cover the
element. The use of undersized pans will expose a portion
of the element which may result in burns, ignition of
clothing or spillovers directly on element.
electrical connection
maximum amp. requirements Btu’s nat Btu’s lP
Model 1850- 35 Amps,240 Volts
1855- 50 Amps,240 Volts
—
—
—
—
Never leave surface units unattended at high heat setting.
Boil over or boil dry conditions could result in a fire.
1860- 5 Amps, 120 Volts 59,000
1865- 30 Amps,240 Volts 43,000
1867- 6 Amps, 120 Volts 79,000
1870- 30 Amps,240 Volts 43,000
1875- 30 Amps,240 Volts 63,000
53,100
38,700
71,100
38,700
56,700
Do not use glass or glazed ceramic cookware on the
surface burners, as sudden change in temperature may
break them.
Always turn off surface unit, before removing pots or
pans.
All ranges come with standard range cord attached. This
cord must be plugged into a standard range receptacle
provided by your electrician.
Turn handle of the pan toward the center of the cooktop,
without extending over nearby elements. This will reduce
the possibility of accidentally overturning the pan.
Let hot pans cool in a safe place, out of the reach of young
children. Never set hot pots on a combustible surface.
installation
Be sure your appliance is properly installed and grounded
by a qualified technician in accordance with the installation
instructions and local building codes.
Do not use decorative metal covers on electric surface
elements. A covered element, when turned on, could result
in a burn or damage to the element.
Power cord installation
frying
The new U.S. revised electrical code states that all new
construction must use a FOUR WIRE range power cord.
Existing construction may use a three wire range power
cord. NOTE: The difference is, a four wire cord has a
separate ground. A three wire cord is grounded through
the neutral.
Use as little oil as possible. Filling the pan too full of oil
can cause spillovers when food is added.
Foods for frying should be as dry as possible. Frost on
frozen foods or moisture on fresh foods can cause hot oil
to bubble up. Spillovers, fire and burns from splatters could
occur.
to change from 3 wire to 4 wire cord:
• Make sure all power is shut off.
• Remove the back panel of the range so the power block
is visible.
Use a deep fat thermometer whenever possible to prevent
overheating oil beyond smoking point.
• Unscrew terminal nuts and remove the range cord wires
from the power block.
• Undo ground screw attaching the white ground wire to the
range body and remove wire.
Deep fryer
Use extreme caution when moving a hot grease kettle or
disposing of hot grease.
• Undo the bushing holding cord to stove body and remove
cord from appliance.
Reassemble the new range cord kit to the range making sure
the white wire goes to the center of the terminal block, the
red to the right and the black wire to the left.
Ventilating hoods
Clean ventilation hood frequently — grease should not be
allowed to accumulate on hood or filter. When flaming
foods under the hood, turn the fan off. The fan, when
operating, may spread flame.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• Attach the ringed terminal of the green or bare copper wire
Note: The metal chassis of the range MUST be earth-
grounded in order for the control panel and burner spark
ignition to work. Check with a qualified electrician if you
are in doubt as to whether the metal chassis of range is
earth-grounded.
to the range body with the green ground screw.
•
Check power with multimeter. You must have 110 volts between
white and black. You must have 110 volts between white and
red. You must have 220 volts between red and black. If range
receptacle is wired wrong, clock transformer will be severely
damaged and will not be covered by manufacturer’s warranty.
Replace back panel of range. Plug the power cord in and
turn power on.
Copies of the standards listed may be obtained from:
* National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
leveling your range
** American Gas Association
1515 Wilson Boulevard
The range must be level in
order to assure uniform
cooking and baking. Shim
legs if required.
Arlington, Virginia 22209
*** Canadian Standard Association
178 Rexdale Boulevard
Rexdale (Toronto), Ontario M9W 1R3
floor covering
Never install a range over inferior kitchen carpeting, vinyl
tile or linoleum. These should be able to withstand at least
175°F without shrinking, warping or discoloring.
safety instructions – gas
important instructions
curtains
Do not use range as a heater. never use the range as a
kitchen heater. Prolonged use of the range without adequate
ventilation can be hazardous. Oven controls and top burners
are not designed for home heating and component failures
that may result from such abuse are definitely not covered by
the warranty.
If your range is near a window, use an appropriate window
treatment. Do not use long curtains which could blow over
the top burners and create a fire hazard.
if you smell gas
If this is a new range installation, your installer has not
done a proper job of checking for leaks. Connections can
loosen in transportation. If the range connections are not
perfectly tight, you can have a small leak and therefore a
faint gas smell.
warning
This product must be installed by a licensed plumber or
gas fitter, when installed within the Commonwealth of
Massachusetts. Massachusetts approval code # G1-1202-18.
#1 This installation must conform with local codes and
ordinances. In the absence of local codes, installations must
conform with American National Standard, National Fuel
Gas Code ANSI Z223.1–latest edition (**) or CAN/CGA-
B149–latest edition (***) installation codes.
finDing a gas leak is usually not a
“Do it yourself” ProceDure.
Some leaks can only be found with the controls in the
“on” position exposing the user to serious burns. Never
use a match or flame to locate a leak. turn off the gas to
the range and call a qualified serviceman.
#2 Input ratings shown on the serial/rating plate are for
elevations up to 2,000 feet (609.6 m). For elevations above
2,000 feet (609.6 m), ratings are reduced at a rate of 4% for
each 1,000 feet (304.8 cm) above sea level.
flame size: Top burner flame size should be adjusted so
it does not extend beyond the edge of the cooking utensil.
Excessive flame is hazardous.
mobile home installation
use of high flame: When using a high flame, never
leave any pans unattended on this heat setting for long
periods. Hot oil is particularly hazardous since it can
become hot enough to ignite.
The installation of this range must conform to the
Manufactured Home Construction and Safety Standards,
Title 24 CFR. Part 3280 (formerly the Federal Standard for
Mobile Home Construction and Safety, Title 24, HUD, Part
280); or when such standard is not applicable, the Standard
for Manufactured Homes Installations 1982 (Manufactured
Home Sites, Communities and Setups), ANSI A225.1q/
NFPA 501A* or with local codes.
Do not obstruct the flow of combustion and ventilation air
to the range.
Any openings in the wall, behind the range or the floor
under the range must be sealed.
in canada
Venting
The installation of this range must conform with the
current standards CAN/CSA-Z240–latest edition*** or
with local codes. When this range is installed in a mobile
home, it must be secured to the floor during transit. Any
method of securing the range is adequate as long as it
conforms to the standards listed above.
Never block the vents (air openings of the range). They
provide the air inlet and outlet which is necessary for the
range to operate properly with correct combustion. The
oven vent is located at the rear of the main top.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
bottom wood or metal cabinets are protected by not
less than 1/4” thick flame retarding millboard covered
with not less than No. 28MSG sheet steel, 0.015” thick
stainless steel, 0.024” thick aluminum or 0.020” thick
copper.
type of gas
Natural and LP Gas (propane). Ranges are factory
assembled for natural gas unless otherwise specified and
cannot be used with LP Gas without some adjustments.
Be sure your range is correctly adjusted by a qualified
serviceman or installer for the type of gas on which it is to
be used. (See Conversion, page 14).
note: Clearances specified to combustible construction
(walls and materials) are based on a temperature rise of
wood resulting from appliance operation. These clearances
are suitable for walls of studding, lath and plaster or other
types of combustible material which have a density of
20 lbs. per cu. ft. or more. No evaluation of clearances
has been made for low density cellulose, fibre board and
similar materials which have a density of less than 20 lbs.
per cu. ft., nor to plastic tiles or sheeting.
note: In this manual, propane is referred to as LP
(liquid petroleum).
installing your range
Installation, adjustment and service of this range must
be performed only by a qualified gas range installer or
electrical serviceman. This is necessary to insure proper
operation of the range and to avoid the possibility of
damage to the range or injury to the users.
The maximum depth of upper cabinets installed above the
range is 13”.
See the minimum clearances chart for electric and gas
models below.
clearances
Observe all the instructions on the rating plate for
minimum clearances to any adjacent vertical combustible
surface. (See figure #1).
WarnIng: Be careful when reaching into storage cabinets
above range while it is in operation. One might accidentally
contact a hot burner when using a hand for support or have
one’s clothing come in contact with top burner flame.
location
If possible, the range should be located to avoid the main
“traffic path” through the kitchen or where an open door
might block a passageway or create an awkward working
situation. If possible, it should be so located where cabinet
working space is available on either side. Drafty locations
should be avoided to prevent gas burner outage and poor
air circulation.
minimum clearances to combustibles
See figure 1 – page 6
all electric
combo
all gas
temperatures
models (1850, 1855)
models (1865, 1870, 1875)
models (1860, 1867)
To cook, you must have heat. Some parts of the range are
therefore going to get warm or even hot. Consider this in
choosing a range location. Do not leave children alone or
unattended near the range when it is in use. Let burner
grids and other surfaces cool before touching them or
leaving them where children can reach them.
A=
B=
C= 30”
D=
E=
0”
0”
3”
3”
32”
0”
3”
3”
32”
0”
0”
0”
0”
0”
F= 13” Max
13” Max
13” Max
1= End of section of overhead cabinet.
2= Overhead center cabinet
3= End wall or divider
clearances
This range may be installed with adjacent surfaces
touching the base cabinets and the back flush with the back
wall. Models 1860, 1865, 1867, 1870 & 1875 gas ranges
require a CGA/AGA approved stainless steel gas flex line
or a flexible copper coil 1/2” in diameter and at least three
feet long so the range can be moved for service.
It is the responsibility of the installer to comply with the
installation clearances specified in this manual.
installation of range into caBinets
To eliminate the risk of burns or fire by reaching over
heated surface burners, cabinet storage above the range
should be avoided. If overhead storage is unavoidable,
clearances between the cooking surface and unprotected
wood or metal overhead cabinets must be no less than
32” (gas models only). The clearances on electric models
between the cooktop and unprotected overhead cupboards
is 30”. This distance may be reduced to 24” when the
The 4 burner range will fit into a 30 1/4” cabinet opening.
Ideal - 31”. The 6 burner range will fit into a 43 1/2”
cabinet opening. Ideal - 44 1/2”.
If you are installing a range with the short leg option,
you will need the following minimum opening size.
30” range - 31”. 44” range - 44 3/4”.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
G
44 1/4"
installing your exhaust hooD
Duct
Your elmira range is equipped with a 350 CFM exhaust
fan located in the warming cabinet. This fan can be vented
directly to the outside or, with the use of the #1442 Charcoal
Filter (included) can recirculate purified exhaust air into the
room.
C
15 3/8"
D
Nickel
Rail
62 1/4"
M
64 1/4"
Charcoal filter should be changed every six months.
See page 20 for Filter Cleaning and Replacement.
Nickel Rail
N
68 1/4"
Ventless installation
Remove the charcoal filter from the broiler pan and
remove plastic wrap. Remove the two screws holding
the mesh filter in place with a #2 phillips or red square
screw driver. Insert the charcoal filter into mesh filter and
replace the assembly. See figure 4
BACK VIEW
OF RANGE
I
28 1/2"
Figure 4
H
To increase efficiency of the charcoal filter system, fan air
should blow against the 45 degree vent deflector at rear of
stove.
30 1/2"
Duct
C
15 3/8"
Vented installation
D
• Remove vent deflector on rear of stove if venting to the
62 1/4"
outside and seal screw holes.
M
64 1/4"
Nickel Rail
• If the exhaust hood is to be vented, the duct location
must be installed in accordance with figure 3, page 7.
Exhaust air must not be vented into a wall, ceiling, attic
or a concealed space of a building.
N
68 1/4"
B
29 1/2"
note: Installation must be in accordance with local
and national building codes. Use only materials which
conform to codes in effect. Disconnect power before
doing any electrical work. Use only metal ducting, do
not use plastic. Assemble securely so that in the event of
a grease fire, the fire will be contained within the metal
ductwork.
Figure 3
BACK VIEW
OF RANGE
exhaust hood Duct location
Figure 3 shows exact center of duct for both four & six burner
ranges. Cut drywall opening 10 1/4” x 3 3/8”.
Never vent exhaust air into a wall, attic, ceiling or any
concealed space of a building, as an accumulation of
grease could pose a fire hazard. Dampers on vented hoods
must open freely and no obstruction should block the
discharge opening.
Height from floor to center of duct on all installations should
be 62 1/4”=D.
Note: Electrical receptacle & gas piping should be located in
center of opening 6” off floor.
Important: If you have purchased the optional in-line
blower, see installation instructions with blower.
Important: If you have purchased the short leg option, D
dimension will be 60 1/4”.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
tools and materials required
• Hammer, Pliers, Tape measure
smooth toP electric cooktoP
• Sabre saw or keyhole saw
surface elements
controls
• #8 x 1/2” sheet metal screws to secure duct
• 3-1/4” x 10” duct, length according to your installation
• 3-1/4” x 10” elbows and adapter, per your installation
• Roof cap or wall venthood
• Caulking or silicone to seal installation
• Slot screwdriver, Electric drill, 3/32 drill bit
The above parts are standard and are available from a
hardware store or heating contractor.
control knobs must be
pushed in before turning
them to a setting. They can
be set anywhere between
MAX and MIN.
The controls for the surface
elements provide infinite
heat settings. The numbers
installation of Ducting horizontally
through an outside wall
Standard 3-1/4” x 10” ducting, elbows, and adapters for
mounting the duct to the range can be purchased at most
plumbing or heating supply dealers.
on the dial serve as a reference. The control can be turned
to any setting to provide the exact heat required.
Before using your glass cooktop for the first time: turn
the elements on max without a pan for 5 to 8 minutes
or until smoking stops. this smoking is normal and
non toxic.
If you can’t find an adapter elbow that will attach to the
exhaust outlet of the range, you can easily make one by
bending the one inch flanges of a standard elbow out
ninety degrees. Put a bead of silicone seal on the flanges
and attach the adapter to the back of the range with four
1/2” x #8 sheet metal screws.
setting
max
recommended use
• To start foods cooking
• To bring liquids to a boil.
• To hold a rapid boil
• To fry foods
• For gravy, pudding and icing
• To cook large amounts of vegetables
• To keep food cooking after starting
it on a higher setting
• To keep foods warm until ready
to serve
8 - 7
6 - 5
4
Cut a 3-3/8” x 10-1/4” hole through the wall directly
behind the warming cabinet outlet, ensuring that no studs
are cut in the process. See figure 3. Push the range into
position. From the outside of the house, measure the
distance from the outside of the siding to the cabinet range
outlet. Cut duct pipe to that length.
3 - 2
1
Attach the vent hood to the duct pipe. Caulk the back
of the vent hood and around the pipe where it will be
pushed into the wall. Insert the vent assembly through the
wall and into the range adapter so that the caulking seals
completely against the siding.
high speed radiant - electric top Burners
Consists of a set of special RADIANT HEATER coils
embedded in thermal insulation. The element is designed
for fast heat response. You can see it light up almost
immediately.
Each element is fitted with a thermal limiter to ensure
the ceramic glass does not exceed the maximum SAFE
operating temperature. You may notice the element going
on and off a number of times during use. This is a normal
occurrence.
Install the mesh filter into the warming cabinet. Do not
install charcoal filter.
installation of Ducting through an attic or
Basement space to an outside wall
To maximize the efficiency of this type of element we
suggest you use it similarly to your previous burner. Turn to
maximum until the desired temperature is reached, then turn
it down to the setting that best maintains the desired heat.
The range may be positioned flush with the back wall
if the vent elbow and pipe are embedded in the wall. If
ducting through the ceiling, continue the vent through
the ceiling into the attic. Terminate the vent either on an
outside wall, below the soffit using a vent hood or through
the roof with a roof cap. If ducting through the basement,
continue the vent through the floor to a point at least 36”
above the grade level. Terminate the vent through the
outside wall using a vent hood. Install the mesh filter into
the warming cabinet. Do not install charcoal filter. If you
are venting more than 10 feet or have more than one 90°
elbow, we strongly recommend the 1518 inline blower.
model ste – smoothtop control
turning burners on
• Touch ON. If highest heat is wanted, touch arrow up.
• If a lower heat setting is required touch arrow down until
the correct setting is achieved.
• If you initially require a low heat setting when turning on
the burner, touch ON then the arrow down. Scroll up to the
desired setting.
note to Installer: Leave these instructions with
the appliance
note to Consumer: Retain these instructions for
future reference.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not cook directly on the ceramic cooktop. The
surface of the cooktop can be damaged, and will be more
difficult to clean.
turning burners off
• Touch OFF
• hot lights are provided in the glass of all smooth top
ranges. Light glows when a burner becomes hot and shuts
off when the burner has cooled.
• Do not use wire trivets mats or aluminum foil. They
offer no cooking advantages and can damage the ceramic
glass surface. Never place plastic or any other material
which might melt on any part of the cooktop.
• H or 9 – To start foods cooking and to bring foods
to a boil.
• 8-7
• 6-5
• 4
– To hold a rapid boil.
• Do not use the cooktop as a chopping board or cutting
surface. This type of use can scratch the surface.
– To fry foods.
– To cook large amounts of vegetables
– To keep food cooking after starting it
on a lower setting.
• Do not leave heavy spills during cooking. Turn heat
off and allow surface to cool down. Remove the spills
with a clean, damp cloth (no detergent), taking care to
avoid burning fingers. If there is detergent in the cloth,
you may leave a layer of soil-laden film on the cooktop
surface, which can result in discolouration next time the
element is switched “on”. If a detergent film builds up,
use a ceramic glass cleaner-conditioner.
• 3-2
• L
– To keep foods warm until ready to serve.
controls
The radiant heating elements are controlled by a commonly
used Infinite Heat Switch that works on the principle of
percent on, percent off. For example, when the switch is
turned to the medium setting, the element will be on only
50% of the time. Because of the fast heat-up with these types
of elements, you will notice the units switching on and off.
care and cleaning
To keep the exterior nickel and porcelain trim in spotless
condition, wipe with a warm soapy cloth. Do not clean
ceramic surface with a soapy cloth while cook surface
is hot.
cookware
The best cooking results and the most economical use of
electricity will be achieved by using smooth, flat-bottom
pans. Pans should be at least the same size or slightly
larger than the cooking area. Ceramic cookware suitable
for stovetop cooking may be used. If pans smaller than the
size of the heating element are used, care should be taken
as the handles may get hot.
See page 31 for complete cleaning guide.
caution - Product Damage hazard
Before using any cleaners, ensure that it is suitable for
application on polished surfaces or trim, e.g. nickel,
anodized aluminum, stainless steel, vitreous enamel,
ceramic glass. Certain cleaners may have an adverse
effect.
Built into each element, is a safety device which protects the
element from overheating. If using pans which are not ideal,
for example concave or convex bottom pans with shiny
bases, or those with ridged or grooved bottoms, the thermal
limiter can cause the element to switch off and on during
cooking, which means that food will take longer to cook.
Make sure that the glass ceramic surface has cooled down
before applying any cleaning materials.
1. saving on cleaning time
• Make sure the bottom of pots and pans and cooking area
are clean and dry.
Very thin, badly dented, and distorted pans with uneven
bottoms should not be used.
Never place utensils with a skirt (e.g. a wok) on the
heated area.
Select correct heat settings and use saucepans large
enough to accommodate food and liquid to eliminate
boilovers and splattering.
Pans should not have rough bottoms. Do not slide pots on
the ceramic glass cooking surface, as this may mark or
scratch the cooktop.
• Wipe up food spills and splatters from adjacent heating
areas before cooking.
If pans with aluminum bottoms are slid across the cooking
surface, metal marks could result. Such marks are easily
cleaned with any non-abrasive stainless steel cleaner,
provided they are removed immediately and not allowed
to bake onto the surface.
• Do not drag or slide pots along the surface.
2. Daily care
• Use a ceramic glass cleaner-conditioner, available
at supermarkets and major department stores. As the
cleaner-conditioner cleans, it leaves a protective coating
of silicone on the smooth surface, which helps prevent
scratches and abrasions in which food particles can
collect. It also helps prevent the build-up of mineral
deposits, and will make future cleaning easier.
Any guidelines or recommendations given by the
saucepan or cooking utensil manufacturer should be
followed.
things not to Do on a ceramic cooktop
• Do not leave pots unattended or elements ON for
extended periods of time. If an element is mistakenly left
on for an extended period of time the built in thermal
limiter will ensure that the heat build-up is insufficient
to cause any adverse effects.
• Apply a dab of cleaner-conditioner in the center of each
heated area to be cleaned.
• For normal cleaning start with about 1 ml (1/8 tsp) of
cleaner-conditioner, and apply more if needed.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
• Clean unit with a damp clean paper towel. To remove
more stubborn spots, use a slightly dampened non-
impregnated plastic or nylon pad specially made for
non-stick utensils.
3. Use cleaner-conditioner, and finally wipe the cooktop
clean with a paper towel or damp cloth.
If after the use of recommended materials there are some
persistent stains or marks on the cooktop, the unit should
be cleaned using a liquid cleanser. This will remove any
accumulated residue of cleaner-conditioner, and if applied
with a non-impregnated plastic or nylon pad for non-stick
pans, for at least three to four minutes, it will also take
off the film caused by salts and minerals before it has an
opportunity to discolor or develop into a problems. Finish
off with a touch of cleaner-conditioner, polish to a high
lustre.
• Use liquid cleansers to remove any discoloration,
especially in hard water areas. A non-impregnated plastic
or nylon pad specially made for non-stick utensils may
also be used with these cleaners. Do not apply excessive
pressure while rubbing. This could cause scratches over
time.
• Apply cleaner-conditioner and polish with paper towel
or a soft dry cloth.
Any smearing or streaking on the surface may be removed
with lightly dampened paper towel and polished with a
soft dry cloth.
• Any smearing or hazing on the surface may be removed
with a lightly dampened paper towel, and polished with
a soft dry cloth.
metal marks
• Do not use a sponge or a dishcloth. They may leave a
film of soil-laden detergent on the heating area which
may turn brown and resemble a discolouration the next
time the area is heated. If that should happen, cleaner-
conditioner will remove it.
Certain metal pots, especially those with aluminum
bottoms may leave marks on the surface, especially if the
pan is allowed to slide. Use the cleaner-conditioner before
the unit is used again to prevent the mark from baking on
the surface.
warning
caution
Personal injury hazard
Product Damage hazard
• note: If a wet paper towel is used to remove spillovers
from warm cooking area, be careful to avoid steam burns.
Ceramic glass cleaner-conditioner should be applied
regularly after use of other cleaners, otherwise over
a period of time the surface of the ceramic glass may
roughen, and cleaning will become progressively more
difficult. Staining may also occur.
• Never mix different household cleaning products.
Chemical mixtures may interact, with objectionable or
even hazardous results.
important notes
Do use
1. In the event of the cooktop being scratched, soil will
collect and appear as fine lines. These are not fully
removable, but can be minimized by the daily use
of cleaner-conditioner. These scratches do not
affect cooking performance.
Ceramic glass cleaner-conditioner should be used
regularly to clean and protect glass-smooth top cooking
surface. If you run out, you may temporarily use baking
soda as a cleaning powder.
2. Soil from sugar solutions must be removed from the
cooktop before the syrup has set, otherwise it can
permanently bond to the ceramic surface.
Do not use
1. Household detergents and bleaches.
2. Impregnated plastic or nylon pads.
3. Soap pads; these will scratch and mark.
electric surface elements
solid cast elements
Before using your solid elements for the first time:
4. Household abrasive powders except where specified;
these may scratch depending on the pressure applied in
use.
Heat the elements at
max without a pan for
3 to 5 minutes or until
5. Chemical oven cleaners, e.g. aerosols and oven pads.
These are caustic cleaners, and may etch the surface.
smoking stops. The
smoking is normal and
non toxic.
Solid elements are
6. Rust stain or bath and sink stain removers, as these will
mark and etch the surface.
7. Metal scrubbers.
sealed with a lacquer coating that prevents corrosion. This
coating must be burned into the elements to be effective in
protecting against rust. The coating will be transferred to
the bottom of pans if this procedure is not done.
Because solid elements are different from coil elements,
you can expect to see differences in cooking performance,
cleaning and safety.
how to Deal with Burned-on spots
1. Make sure area to be cleaned is warm to the touch.
2. The careful use of a stainless steel razor blade held at
approximately 30 degrees to the surface can be used to
remove stubborn burned-on spots from the surface.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Solid elements take longer than coil elements to reach the
set temperature but they retain heat for longer periods of
time after being turned off.
Solid elements are easier to clean up, because the cooking
surface is sealed against spills. There are no drip bowls or
a burner box to clean.
energy tips
Use cookware with tight-fitting lids, and flat bottoms
which completely cover the heated portion of the element.
Watch foods when bringing them to cooking temperatures
at high heat. When food reaches cooking temperature,
reduce heat to lowest setting that will keep it cooking.
Solid elements should not glow red even at max setting.
The red lettering will fade with use.
Use residual heat with surface cooking. For example,
when cooking eggs in the shell, bring water to a boil,
then turn element off, and allow heat in water to complete
cooking.
When boiling water for tea or coffee, heat only the amount
needed. Do not use a wire trivet or any other kind of heat
retarding pad between the pan and the element.
Solid elements have built-in temperature protectors that
automatically reduce heat if a pan boils dry.
You will notice that a cast burner stove top gets hot,
especially when the burners are on for long periods of
time. This is normal for any range with solid elements.
this condition is safe. To minimize heat build up, reduce
burner heat setting to #3 after pot has come to a boil.
selection & use of Pots & Pans
flat Bottoms
griDDle oPtion
Thick, flat bottoms absorb and distribute the heat from
the element more evenly. Thin, uneven bottoms waste
energy and create hot spots that may burn the food onto
cookware.
OPTIONAL
GRIDDLE
Glass cooktops require heavy gauge flat bottom pans for
best cooking results.
Check flatness with a ruler or straight edge. See figure 7.
griddle for electric ranges
To use griddle over the back/front burner combination on
left side of stove. Turn both burners on high for at least five
minutes to allow griddle to heat up to frying temperature.
Temperatures may be adjusted as required.
griddle for gas ranges
Set griddle on the left over the back/front burner
combination. Lock the notches of the griddle onto the
back & front grate fingers. First make sure that grates are
positioned on burners correctly. Turn both front & back
burners on to correct frying temperature.
Figure 7
Pot Diameter
Select element to match pan diameter. The pot should
be slightly larger than the element to obtain best energy
usage, and avoid spillovers flowing directly onto element.
warning: Do not use two griddles on a range as warping
of the top can occur.
Do not use pans extending more than one inch beyond
element, except while canning. See figure 8.
canning
For best results, use a flat bottom, heavy gauge canner.
Canners with rippled bottoms will not work on electric
burners because the bottom does not make enough contact
with the element. This wastes energy and takes a long time
to boil water.
Figure 8
gas cooktoP
Small diameter pans waste energy and spillage can flow
onto element. This increases chance of fire and burns.
for smooth top & cast Burner ranges
Use non-stick coated cookware, for easier clean up.
Glass or pyroceram pans should be used only as the
manufacturer describes.
Gas cooktops are more forgiving than electric cooktops.
Most cookware will work, although tight fitting lids are
recommended for efficient cooking on both. Always
adjust the burner controls so that flames do not extend
past the edges of pots or pans.
Pressure cookers, deep fat fryers, canners, etc. must be of
the correct size and have flat bottoms to work properly.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
note: Low adjustment will not effect flame heights at
other settings. If a top burner flame has been adjusted too
low, the electronic ignitor may start to spark while burner
is on. Readjust flame until ignitor stops sparking.
top Burners
Your gas range is equipped with “state of the art” “Sealed
Gas Burners” and an “Auto-Reignition System”. The
sealed gas burners spread the heat evenly across the
bottom of the cooking utensil and provide infinite heat
control. The auto-reignition system senses when a burner
flame has gone out and will automatically reignite that
burner. There are no standing pilots to light or adjust.
flame appearance
The burners have been pre-adjusted at the factory to a clean
blue flame. On LP gas, a slight orange tip may be visible.
If flame is not as above, your gas servicemen can check
the regulator for proper setting with a water manometer
(U-gauge). The stove pressure should be within + or - 10%
of the pressure setting shown in this manual.
See “Gas Burner Cleaning” for maintenance of top
burners.
gas Burner cleaning
• the burner caps should be routinely removed and
cleaned. Always clean burner caps after a spillover.
Keeping the burner caps clean aids in proper ignition and
an even flame.
HI
9
8
7
6
5
• for proper flow of gas and ignition of the burner, DO
NOT ALLOW SPILLS, FOOD, CLEANING AGENTS
OR ANY OTHER MATERIAL TO ENTER THE GAS
ORIFICE OPENING.
4
LO
3
2
Figure 10
• gas must flow freely through the small hole in the brass
orifice for the burner to light properly. This area must
be free of any soil and be kept protected from boilovers
or spillovers. ALWAYS keep the burner caps in place
whenever a surface burner is in use.
operating range During a Power failure
To light a top burner during a power failure, hold a lit
match to the desired burner head. Turn the corresponding
control knob to any numbered position. After burner
lights, adjust flame to desired setting.
occasionally check the burner flames for proper size and
shape as shown. A good flame is blue in color. If flames lift
off ports they are yellow and usually noisy. You may need
to clean the burners. See figure 12.
note: The “Push to Turn Safety Control Knobs” on
the range are designed for child safety and to prevent
accidental operation.
if ignitors continue to click
the oven requires electricity to operate.
If your ignitors continue to click after lighting, the
probable cause is dirt or moisture around the burner,
or between the burner and ignitor. Clean these areas
thoroughly with household cleaner or soap and water.
Dry thoroughly or sparking may still occur. (You may
have to use a hair dryer to completely dry the area.) If
the condition persists, but on low setting only, you may
need to increase the burner flame (see “Manual Burner
Adjustment” – this page). If the condition persists, check
for damaged ignitors. Very rarely, the spark module may
need to be replaced. Ignitors and spark modules, with
installation instructions, can be ordered from Elmira Stove
Works, and must be serviced from under the cook top.
manual Burner adjustment on low
The burners have been pre-adjusted at the factory for best
performance. You may manually adjust the low settings
up or down by removing the control knob while the burner
is lit and in the low position. While holding the valve stem
so it doesn’t turn, insert a small flat blade screwdriver into
the stem and turn the small brass screw slightly in either
direction until desired flame height is obtained. Valve
must be adjusted so low flame licks around burner cap no
less than 1/8”. See figure 11.
1/8"
to clean Burners:
1. lift the burner cap straight up from the burner base.
2. clean burner cap with warm, soapy water and a sponge.
You can also clean with a nonabrasive scrubbing pad or
cleanser. Do not clean burner cap in dishwasher.
3. if the gas orifice opening has become soiled or clogged,
Figure 11
Figure 12
use a cotton swab or a soft cloth to clean the area.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. if ports are clogged, clean with a straight pin. Do not
enlarge or distort port. Do not leave anything stuck
in the ports when replacing black porcelain burner
base.
ANSI Z223.1 latest edition or in Canada, CAN/CGA B149
installation codes. See page 4 for electrical requirements.
gas Piping to range
The gas supply piping to the range should be 3/4” pipe
which is then reduced to 1/2” at the regulator. With
“LP” gas, the size of the piping to the range should be
determined by your gas fitter.
5. after cleaning the orifice opening and ports, replace the
burner cap. make sure cap is set straight on burner and
that the tabs on cap fit into the grooves of burner base.
6. check the burner for proper lighting after cleaning.
When connecting pipe to the die cast regulator, use two
wrenches. Excess pressure or tightening the pipe too tight
can cause the regulator to crack, resulting in a gas leak or
a possible fire or explosion.
note: If a gas burner burns with an uneven orange
flame, reposition the burner cap so it sits flat on the
burner housing. If burner lights slowly, have your gas
service person check the gas pressure to the appliance.
Make sure that if flexible connectors are used in
connecting the appliance to the gas supply, they are AGA
and/or CGA approved. Poorly designed connectors can
be a source of gas leaks. Even if AGA/CGA approved
flexible connectors are used, the customer should be
cautioned against kinking or damaging the connection
when moving or cleaning the range. This could cause a
gas leak.
If a top burner flame has been adjusted too low, the
electronic ignitor may start to spark. Readjust flame until
ignitor stops sparking.
When cleaning around the surface burner, use care. If
cleaning cloth should catch the ignitor, it could damage it,
preventing ignition.
If surface burner does not light, check if ignitor is broken,
soiled or wet. If clogged, clean the small port beneath the
ignitor using a straight pin.
manual shutoff
Wipe acid or sugar spills as soon as the cooktop has cooled
as these spills will discolor the porcelain.
Install a manual shutoff valve in the gas line, in an
accessible location, near the unit. Know where the gas
valve is so you can shut off the gas to the range quickly.
Suitable pipe thread sealant must be used which is
approved for use with “LP”/Natural gas. Be sure to use
this thread sealant on all pipe connections.
See Cleaning Guide – Page 31.
-
gas toP moDels
oVen Venting
th
Pressure testing
The appliance, and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/3 psig (3.5kPa).
The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve
during any pressure testing of the gas supply system at
test pressures equal to or less than 1/2 psig (3.5kPa).
%
The gas supply pressure for checking the regulator setting
shall be at least one inch w.c. above manufacturer’s
specified manifold pressure.
Hot air and moisture escape from the oven through a vent
in the center rear of the cooktop. Do not block the vent.
Poor baking/roasting and bad combustion can result.
gas leak testing
The oven bottom must be in place for burner to bake
properly on models 1860 and 1867.
After the final gas connection has been made, all the
top burner valves should be closed and the gas supply
and manual shutoff turned on. All connections in the
gas supply line and in the range should be tested with
soap suds or electronic sniffer for leaks. If a leak is
present, bubbles will appear. The leak should be stopped
by tightening the joint, or unscrewing completely and
applying additional pipe dope and re-tightened. Any
factory connections which may have been disturbed
should be retested.
To remove, pull oven bottom forward. Note how tabs on
the oven bottom sit into the oven pan beneath.
gas suPPly system
gas and electrical supplies
Before connecting to the supply systems, be sure that
the installation conforms with the local codes or, in the
absence of local codes, with the National Fuel Code,
14
Download from Www.Somanuals.com. All Manuals Search And Download.
a match should never be used when testing for leaks.
all fittings have been tightened and tested at the
factory. if a leak is detected, tighten the fitting. Don’t
use pipe dope on factory fittings.
conversion of regulator to “lP”
on models 1865, 1870 & 1875
Disconnect Power the range
• Open oven door and remove it, see removal instructions
range conVersion to “lP”
on page 16.
• With a Philips driver, undo the 2 screws holding the top
down.
models 1865, 1870 & 1875
• Pull top forward about 2” then lift front. Raise the
service stay on each side to hold the top up.
(gas top models)
All our ranges are factory set to burn natural gas unless
“LP” is specified. To use the range on “LP” gas, please do
the following:
• On the back right of the range unscrew the nut on top of
the regulator.
• Reverse the white insert pin by pulling it out of the cap,
reverse it, then snap it back into the cap. Replace cap
into body of regulator and tighten, making sure not to
disturb the regulator spring.
order an “lP” kit from the factory. $35 UPS included.
Burner
large
#50 (1.75 mm) #55 (1.32 mm) #57 (1.09 mm)
#65 (.89 mm) #70 (.71 mm)
medium
small
Nat. Gas
LP/Propane #64 (.91 mm)
Store natural gas spuds so they are available for future
conversions.
installation of “lP” spuds
Apply masking tape at the end of a 7 mm nut driver to
help hold the gas orifice spud in the nut driver while
changing it. Press nut driver down onto the gas orifice
spud and remove by turning it counterclockwise and
lifting out, set gas orifice spud aside.
Gas orifice spuds are stamped with a number on the side.
Replace the LP gas orifice spud with the correct Natural
gas orifice spud.
Figure 13 Nat. Gas
LP Gas
a. Pressure regulator:
The pressure regulator is located behind the base skirt
at the back of the range. For best access to the regulator
after range has been moved into place, remove base skirt.
Unscrew the metal nut on regulator behind the plastic cap
with a wrench or vicegrip. Reinstall the plastic cap onto
the threaded end of the metal nut marked LP.
Rethread the nut into regulator making sure nut does not
crossthread. Do not over tighten.
Refer to the following chart for the correct Natural gas
orifice spud placement.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
B. replacing rangetop orifices:
Tools required to replace orifices.
Small adjustable wrench.
1. Remove the lift off burner cap.
2. With the small adjustable wrench, unscrew the brass
venturi and remove.
3. Unscrew the natural gas orifices in each of the top
burners using the 7 mm nut driver included with orifice
kit. Replace with “LP” orifices listed below.
nat. gas
lP/Propane
Front left superburner takes
Other front burners take
All rear burners use
1.75 mm (#50) .91 mm (#64)
1.32 mm (#55) .89 mm (#65)
1.09 mm (#57) .71 mm (#70)
Note: example. Orifices are stamped metric sizes. (00) is
the number drill equivalent.
4. Reinstall the brass
venturi.
Store nat. gas orifices
and nut driver so they
are available for future
conversions.
When replacing the
black caps, make sure
that the tabs in the cap
fit into the grooves of
the burner base.
A. PlAstic cover
B. GAs Pressure reGulAtor cAP with solid end
fAcinG out
c. GAs Pressure reGulAtor cAP with hollow
end fAcinG out
d. wAsher
e. GAs Pressure reGulAtor cAP
conversion of regulator to “lP”
on models 1860 & 1867 (gas oven)
• Locate the regulator at the rear of range (under back legs).
• Remove the plastic cover from the regulator cap.
• With your fingers, turn the nut counter clockwise.
• Do not remove the spring beneath the cap.
• Turn the cap over so LP faces up and reinstall into
regulator.
warning
– fire hazard
• Located gas supply shut off
valve on the press regulator.
• Shut off gas supply before
converting to LP gas.
• Replace plastic cover over regulator cap.
• Make all conversions before
turning gas supply valve back on.
Failure to follow these instructions could result in fire,
explosion or other personal injury.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
check operation of oven Broil Burner
1. Close the oven door.
2. Touch “Broil” and “Start”.
oVen conVersion moDels 1860 & 1867
to convert oven Bake Burner
1. Access from left side as you are facing back of range.
The oven burner should light within 8 seconds, under
certain conditions it may take the burner up to 50 to 60
seconds to light.
2. Use a 1/2” combination wrench to turn the orifice
hood down snug onto pipe (about 2 to 2-1/2 turns).
IMPORTANT: Do not overtighten.
A. orifice hood
B. Pin
c. nAturAl GAs: increAse GAs – increAse flAme size (Preset
At fActory for nAturAl GAs)
adjust oven Broil Burner flame (if needed)
Look through oven window to check broil burner for
proper flame. This flame should have a 1/2” (1.3 cm) long
inner cone of bluish-green, with an outer mantle of dark
blue, and should be clean and soft in character. No yellow
tips, blowing or lifting of flame should occur.
d. lP GAs: decreAse GAs, decreAse flAme size.
to convert oven Broiler Burner
1. Remove oven racks.
2. Use a 1/2” combination wrench to turn the orifice
hood down snug onto the shoulder (about 2 to 2-1/2
turns).
IMPORTANT: Do not overtighten.
The oven broil burner flame cannot be properly adjusted
if this conversion is not made. See “Adjust Oven Broil
Burner Flame” section.
if flame needs to be adjusted:
1. Loosen the lock screw on the air shutter located at the
rear of the broil burner.
2. Adjust the air shutter as need.
3. Tighten lock screw.
3. Complete installation. See “Make Gas Connection”
and “Electronic Ignition System” sections.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Functions are activated by the touch of a finger. The
electronic control generates a beep to confirm that your
message has been received.
aDjusting for ProPer flame
a. cooktop burners:
8 If the control will not function and there is a glowing
indicator light beside the STOP/LOCK function , the
control is locked. Touch and hold STOP/LOCK for 3
seconds to remove the lock. See safety measures.
See page 12 – manual burner adjustment on low.
hiDDen Bake
9 If there has been a power interruption or failure, the
electronic control could either be:
Your electric oven features a hidden bake element.
There is no visible element inside the oven; it is located
underneath oven floor. Hidden bake provides even heat
and easier clean-ups.
A) “Locked up” (meaning no buttons will function).
Reset the main power breaker to the range.
B) Flashing “88:88”. Reset the clock.
electronic oVen control
imPortant information
1 Clock must be set before any other operation of the
oven control is possible.
2 Time of day is always displayed in hours:minutes.
3 The maximum programmable time for BAKE, BROIL,
CONVECTION BAKE, CONVECTION BROIL,
TENDERCOOK, COOK TIME AND STOP TIME is
11 hours 59 minutes.
4 When the appliance is connected to a power supply or
after a power interruption of longer than 2 seconds, the
clock and all indicators flash.
5 If more than 10 seconds elapse between selections, the
program will cancel.
6 Functions are identified on the key pad. When a
function such as BAKE, BROIL, CONVECTION
BAKE, CONVECTION BROIL, CONVECTION,
COOK TIME, SELF CLEAN, TIMER or STOP TIME
is touched, setup begins. The function indicator flashes.
When START is touched, the function indicator glows.
The indicator will shut off when STOP is touched or at
the end of the oven function.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
5
To cancel the timer before the end of the set time, touch
TIMER then touch STOP. The indicator light will shut off.
oVen control caliBration
The maximum length that the timer may be set is 19 hours
59 minutes.
oPeration
The oven control may be recalibrated up to 30 degrees
hotter or cooler. To recalibrate oven,
conVersion
1. Press and hold bake key for 5 seconds until the oven
display shows the current calibration. Screen should
show “CAL” “00”.
from fahrenheit to celsius
Temperature can be displayed in Fahrenheit (°F) or in
Celsius (°C). To switch from one scale to the other: touch
a function key (BAKE, BROIL, CONVECTION BAKE,
CONVECTION BROIL OR CONVECTION) then touch
the key F/C.
2. Press the TEMP “up” or “down” arrow to increase or
decrease the temperature in 10 degree F increments.
The adjustment can be set between plus or minus 30
degrees F.
3. Press START.
Calibration will have to be re-set if you have a power
failure.
changing oVen temPerature
To increase or decrease oven temperature, first touch oven
function indicator. (Bake, Boil, etc.) Then touch the arrow
up or down.
the clock
Bake/Broil/cook settings
oPeration
1 Touch CLOCK. The colon between hours and minutes
stop flashing. The clock indicator begins to flash.
Within 5 seconds go to next operation.
non timeD Bake, conVection
Bake, or conVection
1
Touch BAKE, CONVECTION BAKE or CONVECTION.
A temperature of 350°F (175°C) for bake or 325°F
(160°C) for convection is displayed. Bake, convection
bake or convection indicator keeps flashing.
2 Touch INCREASE or DECREASE to set the clock.
Fast scroll of time begins after holding for 3 seconds.
Once you have reached the desired time, press start.
3
The colon will flash and the CLOCK indicator will shut off.
CLOCK setup is finished and clock is now working.
2 Touch oven function then touch INCREASE or
DECREASE to change the actual temperature setting.
The temperature may be set between a minimum of
100°F and a maximum of 500°F (40°C to 260°C).
4
Touch CLOCK twice to display international (0-24 hours)
time of day instead of the 0-12 hours clock. To return to
the 0-12 hour system, touch CLOCK one more time.
3 Touch START. Oven begins bake function. Oven
function indicator keeps glowing. 5 seconds later, the
actual time and real oven temperature are displayed.
Time of day can only be changed when oven is not in use.
4 The real oven temperature display increases in
increments of 5°. When the programmed temperature
is reached, the control beeps twice and the temperature
becomes constant.
the minute timer
The timer is used strictly for counting down a length of
time. It can be set while the oven is operating, as it does
not control any of the oven functions.
5 Touch STOP if you wish to stop oven operation. The
oven function indicator and the temperature display will
shut off, and only the time of day will be displayed.
setting the timer
6 To verify the oven temperature setting while the oven
is heating up, touch oven function. The temperature
setting is displayed for 5 seconds.
1
Touch TIMER. Timer indicator flashes and clock shows
00:00.
2 Touch INCREASE or DECREASE until desired length
of time is displayed.
3
Touch START. The timer count down starts immediately
and timer indicator stops flashing and glows.
4 Touch STOP when a continuous beep indicates that the
programmed length of time has elapsed.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Touch INCREASE or DECREASE until desired stop
time is displayed.
automatic timeD Bake,
conVection Bake or conVection
The longest delay time which may be set is 11 hours 59
minutes.
1
Touch BAKE, CONVECTION BAKE or CONVECTION.
A temperature of 350°F (175°C) for bake or 325°F (160°C)
for convection is displayed. The function indicator flashes
and the degree indicator glows.
7 Touch START. The display shows the time of day.
Oven temperature is displayed and the oven function
indicator glows when the cooking cycle starts.
2 Touch oven function then INCREASE or DECREASE
to change the actual temperature setting. The
temperature may be set between a minimum of 100°F
and a maximum of 500°F (40°C to 260°C).
When the oven stops, 3 beeps sound. The function
indicators shut off and the time of day is displayed.
3 Touch COOK TIME. The length of time displayed is
00:00. Cook time indicator flashes.
8 Touch STOP if you wish to stop oven operation before
programmed cook time has elapsed or to cancel the
program. The function indicators shut off and the time
of day is displayed.
4 Touch INCREASE or Decrease until desired cook time
is displayed. Fast scroll of time begins after holding for
3 seconds.
To recall cook time, remaining cook time, stop time, or the
oven temperature setting, touch the appropriate button;
the information is displayed for 5 seconds.
5 Touch START. Oven function begins and the indicator
glows. After 5 seconds, the real time and real oven
temperature are displayed. The real oven temperature
increases in increments of 5 degrees. When the
programmed temperature is reached, the control beeps
twice and the temperature becomes constant. When
cook time is completed, an audible signal (3 beeps) is
emitted. The oven stops and display shows the time of
day. The indicator and the temperature display shut off.
Vari-Broil or conVection Broil
1 Touch BROIL, temperature of 500°F (260°C) is dis-
played or CONVECTION BROIL is 450°F. Indicator
begins to flash.
2 Touch oven function then DECREASE to reduce
the preset broiling temperature if desired. Touch
DECREASE or INCREASE to correct temperature.
6 Touch STOP if you wish to stop oven operation before
programmed cook time has elapsed. The oven stops and
the display shows the time of day. The indicator and the
temperature display shut off.
3 Touch START, indicator glows. The real time and set
temperature are displayed.
4 Touch STOP when you wish to end the broiling cycle.
The function indicator shuts off and the time of day is
displayed.
To recall remaining cook time or the oven temperature
setting while the oven is heating up, touch the oven
function or COOK TIME. The remaining cook time and
temperature setting is displayed for 5 seconds.
oVen self-cleaning
DelayeD Bake, conVection Bake
or conVection
WARNING: Remove racks from the oven. Racks will become
dull and blue-gray if left in the oven during a self-clean
cycle. Wipe up any excess oven spills. See page 22 before
self-cleaning.
1
Touch BAKE, CONVECTION BAKE or CONVECTION.
Temperature of 350°F (175°C) for bake or 325°F (160°C)
for convection is displayed. The oven function indicator
flashes and the degree indicator glows.
self-cleaning to start
2 Touch oven function then INCREASE or DECREASE
to change the actual temperature setting. The
temperature may be set between a minimum of 100°F
and a maximum of 500°F (40°C to 260°C).
immeDiately
1 Touch SELF-CLEAN. A countdown timer setting
of “3:00” is displayed to indicate that the length of
cleaning cycle is 3 hours. Self-clean indicator glows
and cook time indicator begins to flash.
3 Touch COOK TIME. The length of time displayed is
00:00. Cook time indicator flashes.
2 Touch INCREASE or DECREASE to change the set
time. The clean cycle can be set from 2 to 4 hours. Four
hours may be required if oven is very dirty.
4 Touch INCREASE until desired cook time is displayed.
Fast scroll of time begins after holding for 3 seconds.
3
Touch START. Self-clean and cook time indicators glow
and the oven door automatically locks (takes approx. 5
seconds). “SC” will be displayed
5 Touch STOP TIME. Stop time indicator flashes and
the display shows the time at which the oven would
normally stop if its operation were not delayed.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Touch STOP to cancel the self-clean program. The self-
clean indicator shuts off. The “SC “ will go off when
the oven temperature falls below 550°F (290°C), at this
time the oven door will unlock. The clock will display
the time of day.
control Panel lock
The oven control can be locked to prevent children from
switching the oven on in your absence. This feature can
also be useful when cleaning the glass control panel.
5 After self-clean cycle is over, the self-clean indicator
shuts off. The “SC” will go off when the oven
temperature falls below 550°F (290°C) and the oven
door unlocks. The clock will display the time of day.
to lock the control, proceed as follows:
1 Touch and hold STOP/LOCK for 3 seconds. A series of
three beeps will sound and the lock indicator will glow.
The control panel is now locked.
DelayeD oVen self-cleaning
1 Touch SELF-CLEAN. A countdown timer setting
of “03:00” is displayed to indicate that the length of
cleaning cycle is 3 hours. Self-clean indicator glows
and cook time indicator begins to flash.
to unlock the control:
2 Touch and hold STOP/LOCK for 3 seconds. A series of
three beeps will sound and the lock indicator will shut
off. The control unlocks.
2 Touch INCREASE or DECREASE to change the set
time. The clean cycle can be set from 2 to 4 hours. Four
hours may be required if oven is very dirty.
stay hot fooD warmer
3 Touch STOP TIME if you wish to delay the start of the
clean cycle. Set the stop time by touching INCREASE
or DECREASE.
Stay Hot Food Warmer is located in the reservoir of all
45” Ranges. This warmer is great for keeping casserole
dishes and dinner plates warm. By flipping the switch on
the side of the reservoir, the stainless steel hot plate in the
reservoir warms to an optimum 200°F.
4 Touch START. The self-clean indicator glows.
5 Immediately the oven door automatically locks (takes
approx. 5 seconds). “SC” glows in the temperature
display and self-clean begins.
6 Touch STOP to cancel the programming or clean cycle.
The clean indicator shuts off. The “SC” will go off
after the oven temperature falls below 550°F (290°C).
The oven door unlocks. The clock will display the
time of day.
miscellaneous features
caBinet light
Touch LIGHT. The lights will turn on. Touch LIGHT
again, the lights will shut off.
After self-clean cycle is over, the self-clean indicator shuts
off. The “SC” will go off after the oven temperature falls
below 550°F (290°C). The oven door unlocks. The clock
will display the time of day.
exhaust fan
Touch FAN. The fan indicator glows and the exhaust fan
is on high. Touch FAN again, the fan will shut off.
Touch SELF-CLEAN to verify the time remaining in the
clean cycle.
in line exhaust Blower (optional)
Touch FAN and the exhaust fan is on. Touch FAN again
and it’s off.
Touch STOP TIME to verify the stop time of the
clean cycle.
safety measures
oVen self-cleaning cycle
For safety reasons, the oven control will automatically
shut off the oven if it has been operating continuously for
12 hours.
how the self-cleaning cycle works
The self-cleaning cycle uses very high heat to burn
away soil and grease. During the cycle, the oven gets
much hotter than it does for normal baking or broiling
– approximately 875°F (468°C). This high heat breaks up
the soil or grease and burns it away.
Your oven is preset for a 3 hour self-cleaning cycle.
However, the cycle time can be adjusted to the amount of
soil in your oven.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start
Porcelain enamel
Porcelain enamel is glass fused on metal and may crack
or chip with misuse. It is acid resistant, not acid proof.
All spillovers, especially acid, milk, tomato or sugar
spillovers, should be wiped up immediately with a dry
cloth. When cool, wash with soapy water, rinse and dry.
Never use oven cleaners on exterior finish of range.
automatic Door lock
As soon as you program the oven for the self-cleaning
function, the door will automatically lock within approx. 5
seconds. It will remain locked throughout the entire cycle.
The door will automatically unlock when the temperature
lowers to a safe level.
maintenance & minor rePair
removable oven Door
The oven door is removable to allow easier cleaning inside the
oven if desired.
removing the oven Door:
Before you start the self-cleaning cycle, make sure you:
• hand-clean the areas shown. They do not get hot
enough during the cleaning cycle for soil to burn away,
and could get baked on during cleaning. Use hot water
and detergent or a soapy steel-wool pad for cleaning.
Oven cleaners may be used in oven but must be
completely removed before self-cleaning cycle begins.
note: Do not clean, move or bend the gasket. Poor
cleaning, baking and roasting may result.
• wipe out any loose soil or grease. This will help reduce
smoke during the cleaning cycle.
• remove the broiler pan grid and anything else being
stored in the oven.
note: If oven racks are cleaned in the self-cleaning
cycle, they will become discoloured and more difficult to
slide.
If you clean racks in the self-cleaning cycle, place them on
the 2nd, 3rd and 4th rack guides.
for Best cleaning results
• clean the oven before it gets heavily soiled. Cleaning a
very soiled oven takes longer and results in more smoke
than usual.
• after the oven is cool, wipe up any residue or ash with
a damp cloth or sponge. If any spots remain, clean with
a mild abrasive cleanser or mildly abrasive pad.
• if the self-cleaning cycle does not get the oven as
clean as you expected, the cycle may not have been
set long enough or you may not have prepared the oven
properly. Set the self-cleaning cycle longer the next time
and hand-clean areas noted above.
Completely open oven door. In both back corners of the
door you will see door latches in the locked position.
Rotate both latches forward to the unlocked position.
Grasp outside edges of door with both hands.
• Begin closing door, at the moment the door stops
closing, lift and pull door toward you.
• Set door aside on a protective surface.
By turning exhaust fan on while self-cleaning most
smoke and odor in kitchen will be eliminated.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
lubrication
rePlacing lights
Lubricate the following with white lubricant:
* Cabinet door hinge & spring (if they squeak).
* Oven door hinges (if they squeak).
to replace oven light on model 1860 and
1867:
1. Unplug appliance or disconnect at the mail power
supply.
If burner control knobs stick, remove knobs and lubricate
around switch shaft with a small amount of white lube.
Replace knobs on switches.
exterior surfaces
The exterior surfaces of your elmira range have been
coated with long-lasting, non-fading textured enamel. This
treatment is far more durable than paint and less fragile
than porcelain.
• Remove all spills immediately to prevent staining. Wipe
the surface with soapy water, rinse thoroughly with
clear water and dry with a soft cloth.
• Do not use abrasive cleansers on enameled surfaces as
they will scratch the finish. VIM, Flitz or Soft Scrub
work well to remove stubborn stains. Follow directions
on the container.
• Should the surface of your range be accidentally
chipped, matching touch-up paint is available from the
factory at a cost of $9.00 plus shipping.
2. Replace the oven lights with a #4452166 15W
appliance bulb. These bulbs are available from a
Whirlpool/KitchenAid dealer or from Elmira Stove
Works.
3. All cabinet lights are the rectangular 12 volt 5 watt
variety as shown below.
to replace oven lights on all models but
1860 and 1867:
All lights on the range are 12-volt, 5-watt (maximum)
halogen bulbs.
filter cleaning & replacement
Shut power off to range. Remove and clean the mesh filter
as required. If a charcoal filter is being used (ventless
installation), it should be replaced every six months.
Before replacing, make sure the oven is off and cool.
1. Disconnect power.
To remove filter, remove the two screws holding the mesh
filter in place with a #2 phillips or red square screw driver.
Wash the mesh filter with soapy water. Rinse and dry.
Insert a new charcoal filter into mesh filter and replace the
assembly.
2. Remove glass light cover by grasping the front edge
and pulling away from oven.
Three charcoal filters are available for $28.00 (plus
shipping) from address on back cover.
Do your switch knobs turn But not
activate Burners?
All top burners use “Push to Turn Switches”. If switch
knobs are not pushed in before turned, they can break. A
set of six replacement knobs is available from the address
on back cover for $20.00 (plus shipping). Please include
model and serial number of range.
3. Remove bulb from socket.
4. Replace bulb, replace bulb cover by snapping back
into wall.
5. Reconnect power.
resetting Breakers
In case of a malfunction, try resetting a breaker, at the
main breaker panel.
serVice
service must be performed by a knowledgeable service
person.
clock malfunction
if in doubt about how to handle service, call the factory
for help at: 1-800-295-8498.
If you have experienced a power surge or loss of power
recently, your clock may have “locked up”. Turn power
off to your range for about 5 minutes then reconnect. This
should reset clock/control and it should now function
normally.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
conVection cooking tiPs
(For Convection Models)
To learn how to use your convection oven to the best
advantage, refer to Convection Cooking on page 26.
1. The fan-forced hot air movement permits baking and
roasting on as many as 3 levels at once.
2. The Delay feature should not be used when using
Convection for baked items e.g.…pies, cakes, cookies.
3. There should be a minimum of 1” (2.5 cm) between
the walls and the pans used.
4. Position food in oven to allow free flow of air around
the convection fan.
5. Uniform spacing of baking dishes will produce the
most even results.
6. Place bread pans lengthwise facing the oven door.
7. Do not use aluminum foil for convection baking. It
may block airflow.
8. True convection cooking is used for baking breads,
cakes and other foods which require gentle heating.
This setting is also recommended when baking large
quantities of food on more than one rack.
imPortant
Proper grounding and polarity are necessary for
correct operation of the electric ignition system
on models 1860 and 1867 (all gas ranges). If the
wall receptacle does not provide correct polarity,
the ignitor will become grounded and click
occasionally, even after the burner has ignited. A
qualified electrician should check the wall receptacle
for correct polarity and grounding. This sparking
condition will also occur if there is a breeze across
the burners.
Note: During convection cooking, the oven door must
remain closed. The fan will operate only when the
door is closed.
Convection cooking creates more moisture in the
kitchen than normal, usually because more food is
being cooked at one time.
9. For convection roasting, do not use a roasting pan
with high sides, as it cuts down the free flow of air
circulating around the food. Use the convection
roasting rack on the broiler pan.
warning: Do not touch ignitor when it is sparking.
10. Convection cooking of frozen convenience foods:
• Preheating the oven is not necessary.
• Cooking times will be similar to package
recommendations. Follow suggestions for oven
temperatures and use of cookie sheets and foil
coverings.
• Most foods are best placed in the middle of the oven.
• If more than one item is being cooked, stagger foods
on multiple racks for proper air circulation.
closed Door Broiling
2. use the broiler pan and grid for broiling. They are
designed to drain excess liquid and fat away from
the cooking surface to help prevent spatter, smoke
and fire.
3. Turn food only once during broiling. Using tongs to
turn meats prevents loss of juices. Use Minute Timer
for timing each side.
roasting tips
• roast meats fat-side up in a shallow pan using a roasting
rack.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
stanDarD oVen meat roasting chart
°
- roast at oven temperature of 325 F.*
*for chicken, set the oven temperature to 350 f.
°
Preheating is not needed.
- Place roasting pan on rack position 1 or 2. See page 25 for rack positions.
aPProximate
meat
thermometer
temPerature
aPProximate
minutes
meat
weight
Per PounD
Beef
rolled rib
• rare
3-5 lbs
6-7 lbs
4-6 lbs
°
25-29
35-37
45-47
140 F
°
• medium
• well-done
standing rib
• rare
160 F
°
170 F
°
23-25
30-32
35-40
140 F
°
• medium
• well-done
rump roast
• medium
• well-done
160 F
°
170 F
°
25-30
35-37
160 F
°
170 F
lamb
leg
6-7 lbs
°
• rare
18-29
21-24
30-32
140 F
°
• medium
• well-done
150-155 F
°
180 F
Pork
°
loin
3-4 lbs
5-6 lbs
4-5 lbs
3-5 lbs
8-10 lbs
45-48
40-44
40-44
17-18
13-14
170 F
°
185 F
°
shoulder
185 F
°
ham, fully cooked
130 F
°
130 F
Poultry
°
chicken*
3-4 lbs
10-16 lbs
18-25 lbs
28-30
14-19
11-15
185 F**
°
turkey, unstuffed
170-180 F
°
170-180 F
Veal
°
loin
3-4 lbs
5-6 lbs
35-38
43-45
170 F
°
shoulder
170 F
25
Download from Www.Somanuals.com. All Manuals Search And Download.
stanDarD oVen Baking chart
approximate
cooking time
(minutes)
approximate
cooking time
(minutes)
food
oven
temperature
food
oven
temperature
Breads, yeast
• loaf
• rolls, pan
miscellaneous
• apples, baked
• beans, baked
• custard, cup
• potatoes, baked
• pudding
bread
cottage
rice
°
375 F
30-40
12-15
°
375 F
50-60
5-6 hrs
35-40
75
°
400 F
°
300 F
Breads, quick
• biscuits
• muffins
• popovers
• corn bread
• nut bread
• gingerbread
°
325 F
°
450 F
10-15
20-25
20-25
25-30
60-75
25-30
°
400 F
°
400 F
°
450 F
°
350 F
45-60
30-40
40-60
60-90
50-60
°
425 F
°
375 F
°
350 F
°
325 F
°
350 F
°
• scalloped dishes
• soufflé
350 F
cakes
°
350 F
°
• angel food
• layer cake
• loaf cake
• sponge cake
• pound cake
• fruit cake
• sheet cake
375 F
30-40
20-30
35-45
35-45
34-45
°
Pastries
• cream puffs
• custard and pumpkin pie 350 F
• pastry shell
• two crust fruit pie
cooked filling
uncooked filling
• meringue topping
350-375 F
°
°
350 F
400 F
35-40
30-40
10-12
°
°
350 F
°
°
350 F
450 F
°
300 F
2-21/2 hrs
25-35
°
300 F
°
400 F
25-30
40-50
10-15
°
cookies
• drop
• rolled and refrigerated
• chocolate
• fruit and molasses
• brownies
400 F
°
°
375 F
10-15
8-12
10-15
10-15
20-30
12-15
350 F
°
375 F
°
375 F
°
375 F
temperatures and times are guidelines only and may
°
need to be adjusted to individual tastes.
350 F
°
• macaroons
350 F
Broiling chart:
The recommended rack position is numbered lowest (1) to highest (5). Preheat broiler for five minutes before placing food in oven.
aPProximate
rack
Position
time (minutes)
meat
temPerature
siDe 1
siDe 2
°
steak, 1” thick
• rare
4
500 F
4
6
8
4
6
8
• medium
• well-done
steak, 1 1/2” thick
• rare
°
4
500 F
8
8
• medium
10
10
hamburger patties or steaks, 1/2” thick or less
°
• medium
4
500 F
6
9
4
9
°
lamb chops, 1” thick
4
400 F
°
ham slice, 1/2” thick
precooked 1” thick
Pork chops, 1” thick
frankfurters
4
4
4
4
3
3
4
500 F
5
10
12
4
5
10
12
4
°
500 F
°
450 F
°
500 F
°
chicken pieces
500 F
16
10
5
16
10
5
°
fish, 1” thick
350 F
°
Beef liver, 1/2” thick
350 F
temperatures and times are guidelines only and may need to be adjusted to individual tastes.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
• use a roasting pan that fits the size of the food to be
roasted. Meat juices may overflow the sides of a pan that
is too small. Too large of a pan will result in increased
over spatter.
4. Place food on a cold pan to prevent sticking. If the rack
is hot, grease it or grease the food.
convection roasting rack
(On Convection Models)
• spatter can be reduced by lining the bottom of the
roasting pan with lightly crushed aluminum foil.
The Convection Roasting Rack is a specially designed
rack, ideal for use when roasting and broiling meats using
the Convection Bake and Convection Broil functions.
Place it in the broiler pan instead of the regular grid. It
raises the meat for better airflow to all sides for more even
roasting and broiling.
• a foil tent will slow down surface browning for long-
term roasting, as when roasting a turkey. Place tent-
shaped foil loosely over meat to allow for air circulation.
Do not seal foil or meat will be steamed.
air circulation
The hot air must circulate around the pans in the oven for
even heat to reach all parts of the oven. This results in
better baking.
• use an accurate meat thermometer to determine when
meat has reached desired degree of doneness. Insert the
thermometer into the center of the thickest portion of the
meat or inner thigh or breast of poultry. For an accurate
reading, the tip of the thermometer should not touch fat,
bone or gristle.
for best air circulation:
• Place the pans so that one is not directly over the other.
• For best results, allow 1-1/2” to 2” (3.7-5 cm) of space
around each pan and between pans and oven walls.
There must be a minimum space of 1” (2.6 cm).
• after reading the thermometer once, push it further
into the meat 1/2 inch or more and read again. If the
temperature drops, return the meat to the oven for more
cooking.
• check pork and poultry with a thermometer in 2-3
places to ensure adequate doneness.
• Poultry and roasts will be easier to carve if loosely
covered with foil and allowed to stand 10-15 minutes
after removal from the oven.
• When baking with one pan, place pan in the center of
the oven rack.
• When baking with two pans, place pans in opposite
corners of the oven rack.
convection Broiling
(On Convection Models)
1. keep the oven door closed.
2. use the convection roasting rack and broiler
pan for convection broiling. Convection broiling
is essentially high-temperature convection cooking,
combining fan-circulated hot air with the direct heat of
the broiler element.
3. Do not cover the roasting rack with tin foil as this will
block air flow and extend cooking time.
4. The circulating air creates a seal on all sides of the
food so that turning of foods is often not necessary.
note: Opening the oven door may cause heat loss,
longer cooking times and unsatisfactory baking or
roasting results. Rely on your timer.
general Broiling tips
1. The surface of the food should be at least 3” (7.4 cm)
away from the broil element.
2. For steaks and chops, slash fat evenly, at 2” (5 cm)
intervals, around the outside edges of meat to prevent
curling.
3. Meats and poultry can be marinated before broiling.
Brush foods with barbecue sauce only during the last 5
to 10 minutes of broiling.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
oven rack Positions
rack
Position
fooD
Frozen Pies
1 or 2
2
Angel and bundt cakes,
most quick breads, yeast breads,
casseroles, meats
Cookies, biscuits,
muffins, cakes,
non frozen pies
2 or 3
using aluminum foil in the oven
Your oven has five rack positions. Rack position 1 is the
lowest position, or closest to the bottom of the oven. Rack
position 5 is the highest position, or farthest from the
bottom of the oven.
Do not use aluminum foil for convection cooking.
aluminum foil may block airflow.
Do not cover the broiler grid with foil. Poor drainage
of grease may result in a fire.
There are three straight racks. Be sure to position the oven
rack(s) before putting food into the oven or turning the
oven on.
When using aluminum foil for non-convection cooking
to catch spillovers from pies or casseroles, follow these
instructions.
to remove oven racks:
• Place the foil on the oven rack below the rack with
the food. Turn foil edges up and make sure foil is about
1 inch (2.5 cm) larger all around than the dish holding
the food.
• Do not cover the entire rack with aluminum foil.
It will reduce air circulation and cause poor cooking
results.
Lift rack at front and pull out.
to replace oven racks:
1. Place rear of rack on rack guides.
2. While lifting front of rack, push in all the way. Lower
front.
for Proper cooking,
follow these guidelines:
• Do not line oven bottom or entire oven rack with foil
or other liners. Poor baking will result.
• when using one rack, place the rack so the top of the
food will be centered in the oven.
• when using two racks, place racks in positions 3 and 1
(the closest to the oven bottom).
• use only one cookie sheet in the oven at a time when
using the regular Bake setting.
rack Placement for specific foods:
(For rack positions, see “Rack Positions” at the top of this
page.)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
introDuction to conVection cooking
welcome to convection cooking, the ultimate culinary
Preheating
technique that uses fan-circulated hot air to efficiently
When preheating the oven is specified in a recipe, normal
time is approximately 10 minutes.
create delicious meals with appetite appeal.
BROIL ELEMENT
air flow
5
The secret to convection cooking lies in maintaining a
consistent temperature throughout the oven during the
cooking process. The fan circulates hot air in your convection
oven continually to distribute heat more evenly than the
natural movement of air. This fundamental difference means
food is cooked on all sides, sealing in natural flavour and
moisture. Avoid blocking the air circulation fan at the rear
of the oven with a large dish, as this will interrupt free flow
of air throughout the oven. It is important not to cover foods
with foil, so that surface areas remain exposed to the moving
air. The effective use of circulating air also means that many
of your convection creations require shorter cooking times at
lower oven temperatures, so you enjoy the added benefits of
less time spent in the kitchen, and greater energy savings.
4
CONVECTIONELEMENT32
1
BAKE ELEMENT
uniform results. You may choose to cook your main course
and side dishes or dessert, at the same time. For greatest
success with multi-level cooking, stagger dishes on opposite
corners of the oven racks to the ones above and below. Be
sure to leave at least one inch (2.5 cm) of space between the
individual pans, and the diagram shown here indicates which
convection feature and rack position you should be using for
that particular recipe. At the Convection setting, the center
element surrounding the fan at the rear of the oven is on. At
the Convection/Broil setting, the top element in the oven will
conVection meat roasting chart
Set Cooking Selections to: ConveCtion/Bake
R - Rare M - Medium WD - Well Done
internal
aPProximate
temPerature
cooking time
Per lB. (500g)
rack
Position
oVen
temPerature
of meat
when cookeD
fooD
Beef
Standing Prime Rib
R - 20-25 min
M - 25-30 min
WD - 30-35 min
140°F/60°C
160°F/70°C
170°F/75°C
2
2
2
300°F/145°C
300°F/145°C
300°F/145°C
Rolled Rib
R - 22-25 min
M - 27-30 min
WD - 32-35 min
140°F/60°C
160°F/70°C
170°F/75°C
Rump, Sirloin Tip
R - 20-25 min
M - 25-30 min
WD - 30-35 min
140°F/60°C
160°F/70°C
170°F/75°C
Pot Roast (braised)
Meatloaf
35-40 min
20-25 min
2
2
300°F/145°C
325°F/160°C
170°F/75°C
170°F/75°C
Veal
Leg, Loin, Rib
Shoulder, Blade
Pork
M - 25-35 min
2
2
325°F/160°C
300°F/145°C
160°F/70°C
170°F/75°C
WD - 30-40 min
Loin
30-40 min
35-40 min
25-30 min
2
2
2
325°F/160°C
325°F/160°C
325°F/160°C
170°F/75°C
170°F/75°C
170°F/75°C
Shoulder
Tenderloin
ham
Fresh (uncooked)
Pre-cooked
lamb
25-35 min
15-20 min
2
2
300°F/145°C
300°F/145°C
170°F/75°C
140°F/60°C
Leg, Shoulder
M - 25-30 min
2
2
300°F/145°C
300°F/145°C
160°F/70°C
170°F/75°C
WD - 30-35 min
Rib, Rack, Loin
M - 20-25 min
WD - 25-30 min
2
2
160°F/70°C
170°F/75°C
29
Download from Www.Somanuals.com. All Manuals Search And Download.
heat up. At the Convection/Bake setting, the lower element
will be in use. Rack positions number from 1 at the bottom
to 5 at the top.
Bakeware selection
Bakeware with lower sides allows for constant air circulation
around all surface areas of food, for more even cooking. High-
sided casserole dishes and bread pans should be positioned
on the lower racks in the oven where they will benefit from
optimal heat distribution. For the most appetizing browning
results, use matte or dull finish metal pans as they conduct heat
more efficiently. Dark finishes on bakeware will absorb more
heat than reflective surfaces, resulting in darker, crispy bottom
crusts more suitable for pies and breads. Shiny muffin tins,
cake pans and cookie sheets tend to reflect heat, producing
light, tender crusts. Glass, ceramic, and stainless steel dishes
may not transmit heat as evenly as metal bakeware.
convection Baking and roasting
Your convection oven utilizes precise, consistent
temperature control to ensure absolutely even baking and
roasting results. In particular, foods that require browning
are greatly enhanced by the hot air convection cooking
method. Depending on the quantities you wish to prepare,
convection cooked foods can be positioned on single or
multiple racks. When roasting whole poultry or large cuts of
meat, you can effectively lower oven temperature settings,
and substantially reduce cooking times. You will notice the
remarkable difference in convection cooked foods.
Perfect Poultry
Preheating your oven to cook poultry is often not necessary,
but we do suggest that you consult your individual recipes
first. As you will notice in the Convection Poultry Roasting
Chart, convection roasting temperatures are generally 25°F
(15°C) lower than those used in conventional ovens.
memorable meats
Convection cooking techniques contribute special appeal
to your meat dishes by locking in flavour and retaining
moisture. The result is meat that is evenly browned outside
and tender and naturally juicy inside.
Poultry is completely cooked when an accurate meat
thermometer, inserted at the thickest part of the breast or
inner thigh, registers 185°F (85°C). The juices will run clear
and the meat should pull easily away from the bone.
Before roasting or broiling, brush the entire surface of lean
meats with butter or oil. This will increase moisture retention
and enhance browning. Position cuts of meat, uncovered,
on the raised convection roasting rack, so that heat freely
reaches all sides.
Glazes or sauces may be brushed onto poultry during the last
half of cooking time, for the perfect finishing touch.
Convection oven methods can conveniently reduce the
length of time required to roast meats, in comparison to
conventional roasting. Therefore, meat should be checked
shortly before the end of recommended cooking times, to
avoid over-cooking.
Delicate fish & seafood
A limitless variety of fish and seafood can be elegantly
prepared using different convection cooking methods.
Variable Convection/Broil temperature settings offer you
greater diversity compared to conventional broiling.
Insert an accurate meat thermometer into the thickest part of
the meat, taking care to avoid any bone, fat or gristle. Once
the desired internal temperature is reached, remove the meat
from the oven and let stand for a few minutes. This allows
the juices to settle for easier carving.
Before Convection/Broiling we recommend that you baste
all surface areas of your fish and seafood with oil or butter.
Reduce your oven temperature for broiling thin fillets, and
use a higher setting for broiling thicker fish steaks. Lower
temperatures may require longer cooking times, but thorough
hot air circulation eliminates the need to handle or turn
fragile fish during convection cooking.
convection Broiling
Convection broiling is essentially high-temperature
convection cooking, combining fan-circulated hot air with
the direct heat of the broiler element. We recommend
preheating your oven first to maintain an even temperature
during cooking. Convection broiling times will depend
upon the variable temperature selected and the rack position
used. Do not cover the broiling rack with tin foil as this will
block air flow and extend cooking time. The oven door must
remain closed while convection broiling. Circulating air
creates a seal on all sides of the food so that turning foods is
often not necessary.
Testing fish and seafood during the last few minutes of
recommended cooking time will ensure flawless results
without over-cooking. When the fish is opaque and flakes
easily, remove from the oven and serve.
savory Vegetables & side Dishes
Oven-baking your vegetables is no longer limited
to potatoes! Take full advantage of multi-level cooking
and simultaneously prepare appetizing, piping hot
accompaniments to your main meal with no cross-over
flavors. Continuous heat distribution throughout your
convection oven offers you the opportunity to efficiently
prepare a variety of side dishes and vegetables.
As you prepare your own favorites, remember that more
dense rice and pasta casseroles may require longer cooking
times. To allow for thoroughly cooked centers without over-
browned outside edges, lower oven temperatures at least
25°F (15°C), but not lower than 300°F (145°C).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
conVection Poultry roasting chart
Set Cooking Selections to: tRue ConveCtion
internal
temPerature
of Poultry
aPProximate
oVen
aPProximate cooking time
rack
Position
temPerature
fooD
weight
Per lB. (500g)
not PreheateD when cookeD
Chicken, Whole
3 - 5 lb.
20-25 min
2
325°F/160°C
325°F/160°C
185°F/85°C
185°F/85°C
(1.5 - 2.2 kg)
Parts, Quarters
3 lb.
(1.5 kg)
18-25 min
2 or 3
Turkey, Unstuffed
13 lb. and under
(5.85 kg)
10-15 min
10-12 min
2
300°F/145°C
300°F/145°C
185°F/85°C
185°F/85°C
over 13 lb.
(5.85 kg)
1 or 2
Capon, Unstuffed
Domestic Duck
Domestic Goose
Cornish Hen
4 - 7 lb.
15-20 min
2
2
325°F/160°C
185°F/85°C
(1.8 - 3.1 kg)
3 - 5 lb.
(1.5 - 2.2 kg)
25-30 min
then 15 min
325°F/160°C
400°F/205°C
185°F/85°C
185°F/85°C
4 - 8 lb.
(1.8 - 3.6 kg)
30-35 min
50-60 min
2
300°F/145°C
185°F/85°C
1 - 1.5 lb.
(0.5 - 0.7 kg)
2 or 3
325°F/160°C
185°F/85°C
Stuffed poultry may require additional cooking time.
incredible egg & cheese Dishes
You’ll be delighted with the significant difference convection
cooking makes, particularly to the preparation of dishes that
are sensitive to fluctuations in oven temperature.
effortless Quick Breads
Whether your family’s preference leans toward delicious
snack muffins or a hearty fruit and nut loaf, your convection
range makes baking their favourites easy and rewarding!
With a consistently maintained temperature throughout the
oven, a fabulous soufflé, with a light-textured interior and
an exquisitely golden crust, will no longer elude you. You’ll
enjoy complete success creating ham and swiss cheese
soufflé as egg whites rise evenly while the wonderful flavour
of cheese is gently blending in.
Using a preheated oven will ensure quick breads are
completely cooked in the center and delicately browned
outside.
Enhanced heat distribution during convection baking may
finish smaller items, such as biscuits and muffins, sooner than
you might anticipate. Check for the desired level of doneness
shortly before the end of recommended cooking times.
Most egg and cheese dishes bake higher and lighter using
the constantly moving air in a convection oven. Positioning
dishes in the center of the oven makes efficient use of evenly
distributed heat, guaranteeing perfect results with your egg
and cheese dishes.
The moisture content and density of quick breads require
convection oven temperatures within the same range as
conventional baking temperatures.
conVection yeast BreaD Baking chart
Set Cooking Selections to: tRue ConveCtion
PreheateD
oVen
aPProximate
cooking
time
size of
rack
fooD
yeast Breads
Loaves
Baking Dish
Position
temPerature
Bread Pans
9” x 5” (23 cm x 13 cm)
2
350°F/175°C
30-35 min
Dinner Rolls
Single Pan
Multiple Pans
3
1, 3
350°F/175°C
350°F/175°C
10-15 min
12-15 min
homemade Pizza
Single
Multiple
3
2, 4
400°F/205°C
400°F/205°C
15 min
15-20 min
31
Download from Www.Somanuals.com. All Manuals Search And Download.
conVection Quick BreaDs Baking chart
Set Cooking Selections to: tRue ConveCtion
PreheateD
oVen
aPProximate
cooking
time
size of
rack
fooD
yeast Breads
Muffins
Baking Dish
Position
temPerature
Single Pan
Multiple Pans
3
375°F/190°C
425°F/220°C
18-25 min
18-25 min
1, 3, 5
Biscuits
Single Sheet
Multiple Sheets
3
8 min
10 min
1, 3, 5
Fruit & Nut
Loaves
Loaf Pan
8” x 4” (21 cm x 12 cm)
2
325°F/160°C
45-60 min
conVection Dessert Baking chart
Set Cooking Selections to: tRue ConveCtion
PreheateD
oVen
temPerature
aPProximate
cooking
time
size of
Baking Dish
rack
Position
fooD
cookies
Dropped
Single Sheet
Multiple Sheets
3
350°F/175°C
350°F/175°C
8-10 min
10-12 min
1, 3, 5
Rolled
Single Sheet
Multiple Sheets
3
375°F/190°C
375°F/190°C
8-10 min
10-12 min
1, 3, 5
Brownies
Loaves
Square Pan
8” - 9” (20 cm - 23 cm)
2
325°F/160°C
35 min
conVection Dessert Baking chart
Set Cooking Selections to: tRue ConveCtion
PreheateD
oVen
temPerature
aPProximate
cooking
time
size of
Baking Dish
rack
Position
fooD
cakes
Round or Square Pan
8” - 9” (20 cm - 23 cm)
Single Pan
2
2, 4
325°F/160°C
325°F/160°C
30-35 min
30-35 min
Multiple Pans
Rectangular Pan
9” x 13” (23 cm x 33 cm)
2
325°F/160°C
30-35 min
Bundt Pan
10” (25 cm)
2
2
325°F/160°C
325°F/160°C
40-45 min
20-25 min
Cupcakes
Loaf Pan
9” x 5” (23 cm x 13 cm)
2
2
325°F/160°C
325°F/160°C
50-60 min
35-40 min
Angel Food or
Spring Form Pan
Pies
With Filling
Single 9” (23 cm)
Multiple 9” (23 cm)
3
375°F/190°C
375°F/190°C
50-55 min
55-60 min
1, 3, 5
Without Filling
Single 9” (23 cm)
Multiple 9” (23 cm)
3
375°F/190°C
375°F/190°C
8-10 min
8-10 min
1, 3, 5
32
Download from Www.Somanuals.com. All Manuals Search And Download.
B L A C K
17 RED
18 RED
23 BLACK
33 WHITE
EXHAUST
FAN
#33 WHITE
21 BLACK
# 2 WHITE
# 3 BLACK
#32 BLACK
TOD
#31 BLACK
W
M
BLOWER
#15 BLACK
#28 BLACK
BLACK 10C
#30 WHITE
12 WHITE
M
CONV. FAN
RED 13
14 RED
RED 25
26
RED
#22 BLACK
16 BLACK
27 BLACK
LIGHT POWER SUPPLY
BK
29 BLACK
19 RED
9 WHITE
HALOGEN
5W/BULB
BK
BK
W
W
BK
W
C K
# 5 B L A
#7 RED
#34 RED
TOD - RESETABLE
11C
CONV.
BLACK
W H # I 1 T E
N W O
1 A B R
8 RED
6 BLUE
BROIL
33
Download from Www.Somanuals.com. All Manuals Search And Download.
cleaning guiDe
Part
what to use
how to clean
control knobs
• Soft sponge
• Warm, soapy water
• Turn knobs to OFF and pull straight off control panel.
• Wash, rinse and dry thoroughly. Do not soak.
• Replace knobs. Make sure all knobs point to OFF.
Do not use steel wool or abrasive cleaners. They will
damage the finish.
glass control Panel
• Soft sponge OR
• Soft Cloth
• Warm, soapy water
• Spray glass cleaner
• Wash, rinse and dry thoroughly.
Do not use steel wool or abrasive cleaners. They will
damage the finish.
note: Lock control when cleaning panel.
See page 18 for details.
in cabinet
exterior surfaces
• Soft sponge
• Wash, rinse and dry thoroughly.
• Use non-abrasive, plastic scrubbing pad on heavily soiled
areas.
• Follow directions on the container.
• Do not use abrasive or harsh cleaners.
• Warm, soapy water
• VIM, Flitz or Soft Scrub
cleaners
glass cook top
(electric models)
• Soft cloth with warm, soapy
water
• Vim or Glass Stove Top Cleaner
• Corning Cleaner-Conditioner
• Dry Baking Soda
• Follow directions on container.
• Do not use abrasive or harsh cleaners.
• Apply to soiled areas dry with soft cloth.
country motif
• Mild soap and warm water only
• Don’t use cleaners with
ammonia like windex
• Wash, rinse and dry thoroughly.
(optional Painting)
Porcelain-enamel
• Wipe off excess spills.
• Wash, rinse and dry thoroughly.
• Non-abrasive, plastic scrubbing pad
• Warm, soapy water
• Wax with Turtle Wax monthly
cook top & gas grates
also see page 23
front Door Vent
• Abrasive cleaner
• Use abrasive cleaner to remove stains, if required.
Broiler Pan & grid
• Wash, rinse and dry thorough OR
• Leave in oven during self-cleaning cycle.
• Steel-wool pad
• Warm, soapy water OR
• Self-cleaning cycle
(Clean after each use)
• Steel-wool pad
• Wash, rinse and dry thoroughly
oven racks
• Warm, soapy water OR
• Self-cleaning cycle
• Remove from oven during self-cleaning cycle.
note: Racks will discolor and become harder to slide if left
•
Maas cleaner, follow directions on tube in oven during self cleaning cycle. Apply a small amount of
nickel trim
• Tarnite metal polish (follow
vegetable oil to the side rungs to aid sliding.
directions on can)
Brass or copper trim
• Wash, rinse and dry thoroughly.
• Mild soap and warm water
or Windex – no abrasives
• No brass/copper cleaners
(optional)
how can i clean stains
• Wash, rinse and dry thoroughly.
• Follow directions on the container.
• Soft sponge
off enamel or nickel?
• Warm, soapy water OR
• Windex
• Maas Cleaner (available at
most hardware stores)
• Soak then wash in hot soapy water.
• Wash in hot soapy water and rinse.
• Replace every six months.
• Plastic scouring pad with
Pancake griddle
(Option)
soap & water
• Soak in hot soapy water
exhaust fan
mesh filter
charcoal filter
permanent staIns to Cooktop, nICkel, brass or Copper trIm:
acid (tomato, cherries, rhubarb, citrus, milk and vinegar) will permanently stain cooktop and trim if not wiped
up immediately.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
range trouBleshooting
This section is designed to help you save the cost of a service call. However, you may still need assistance or service. When calling
for service, you will need to provide a complete description of the problem, your appliance’s complete model and serial numbers
and the purchase or installation date (see Warranty). This information is needed to properly identify parts needed.
Before calling for service…Phone our helP line at: 1-800-295-8498
If your range should fail to operate, review the following list before calling for service.
Note: Most electrical clock malfunctions can be corrected by turning the power off to the range for about 5 minutes.
(Clock and Control will reset itself).
Problem
check…
what to Do
Nothing will operate
• Is the power cord plugged into a live
circuit with proper voltage?
• Plug the power cord into a live circuit
with proper voltage.
• Has a household fuse blown or a circuit
breaker tripped?
• Replace household fuse or reset circuit
breaker.
The oven will not operate
• Has the clock been set?
• Have the electronic controls been set
correctly?
• Refer to instructions for setting the
electronic controls starting on page 18.
• Has a delayed start time been
programmed?
• Wait for the start time
to be reached.
The electric surface elements
will not operate
• Has a household fuse blown or a circuit
breaker tripped?
• Replace household fuse or reset circuit
breaker.
• Are the control knobs set correctly?
• Push control knobs in before turning to
a setting.
• Is a control knob sticking or broken?
• See LUBRICATION on page 20.
Cooktop control knobs will not turn
• Are you pushing in before turning?
• See LUBRICATION page 23.
• Push control knobs in before turning to
a setting. Call factory for help.
The self-cleaning cycle
will not operate
• Does the range clock show the correct
time of day?
• Reset clock to show the correct time of
day (see page 19).
• Has a delayed start time been
programmed?
• Wait for the start time to be reached or
reset for immediate start.
• Has there been a power failure?
• Reset the clock (see page 19).
The display will show “88.88”
Control is “locked up” (meaning no
buttons will function)
• There has been a power interruption.
• Reset the main power breaker to the
range. Turn off for 1 minute.
• Temperature sensor in oven?
• Press CANCEL and wait for 1 minute.
Shut power off at breaker for 15 seconds.
If problem persists, call factory for service.
“F1” or “F2” appears in the time display
Cooking results are not what
you expected
• Is the range level?
• Level range (see Leveling Your Range
page 6).
• Preheat oven when called for in recipe.
• Use only tested recipes from a reliable
source.
• Refer to a reliable cookbook for
recommended pan type and size.
• Allow 1” to 2” (3.5-5 cm) of air space on
all sides of pan.
• Pan should be the same size or slightly
larger than surface element being used.
• Is the oven preheated before baking?
• Has the recipe been tested or is it from a
reliable source?
• Is the pan used the type or size
recommended in a reliable cookbook?
• Is there proper air circulation around the
pan when baking?
see page 19 for instructions on how to
recalibrate oven temperature
• Does cooking utensil fit the surface
burner being used?
gas trouBleshooting
Problem
check…
what to Do
Ignitor doesn’t spark when knobs are
turned to light.
Dirt on ignitor, or defective spark module or Clean ignitors and area between ignitor and
valve switch. burner. Replace module or valve switch.
Burners spark but one does not light.
Check burner, cap, ignitor and orifice for dirt. Clean dirt from burner, cap or orifice.
Spark occurs at ignitor when all control
knobs are off.
Module.
Water has been spilled on control panel.
Replace module.
Unplug range and let control panel dry overnight.
caution: Do not run burners without pots in place. excessive heat could damage clock/control above burners.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts of your range
1. Exhaust Blower ........................................................... #1540
2. Cabinet Door Spring.................................................... #1591
4A. Clock Control Power Board - 120 V........................... #1489
5. Cabinet Front (Nickelled)............................................ #1077
9. Charcoal Filter for Exhaust Hood (3 per pkg.)........... #1442
10. Mesh Filter for Exhaust Hood..................................... #1441
11. Electric Element for Glass Top – 1500W .................. #1477
11. Electric Element – Cast – Small ................................. #1479
11C. Glass Top with Frame & Elements – ST or STE........ #1467
11D. Glass Top with Frame & Elements – ST or STE........ #1468
12. Electric Element for Glass Top – 2000W ................... #1478
12. Electric Element – Cast – Large.................................. #1480
*12A. Burner Cap (Small) ..................................................... #1564
*12A. Burner Cap (Medium)................................................. #1565
*12A. Burner Cap (Large) ..................................................... #1566
13A. Switch Knob (Electric)................................................ #1578
13B. Switch for Large Burner (2000W) .............................. #1359
13C. Switch for Small Burner (1500W) .............................. #1358
*13F. Gas Valves for Top Burners........................................ #1581
*13G. Switches for Gas Valves ............................................. #1583
*13H. Knob for (13F) Gas Valve........................................... #1573
36. Cabinet Brackets – Right............................................. #1079
Cabinet Brackets – Left............................................... #1080
37. Casting, Side Skirt (Right or Left) .............................. #1057
38. Leg............................................................................... #1036
39. Casting, Front Skirt ..................................................... #1053
40. Handles for Fire & Oven Door (Nickelled) ................ #1576
41. Oven Door Gasket....................................................... #1325
42. Porcelain Oven Door Liner ......................................... #1387
43. Power Block (Bakelite) – 110V & 240V .................... #1381
*44. Spark Module, 4 Burners – Reignition........................ #1579
*44A. Spark Module, 6 Burners – Reignition........................ #1580
*45. Gas Regulator, (Models 1865, 1870, 1875) ................ #1497
*45A. Gas Regulator (Models 1860, 1867) ........................... #1270
*46. Cast Grate.................................................................... #1568
*47. Burner Bezel – Porcelained,
(Holds Small Burner) ...............................................#1074-8
*47A. Burner Bezel – Porcelained,
(Holds Medium Burner) ..........................................#1074-12
*47B. Burner Bezel – Porcelained,
(Holds Large Burner) ..............................................#1074-15
48. Convection Fan (110 Volts)........................................ #1377
48A. Convection Element (Round)...................................... #1365
48B. Convection Baffle ....................................................... #1318
*48C. Gas Deflector, Oven Bottom....................................... #1262
49. Oven Sensor ................................................................ #1351
50. Glass Control Panel - Self Clean................................. #1485
50A. Glass Control Panel - Convection............................... #1486
52. Installation & Operating Manual-All Models..........#1604-8
53. Pancake Griddle For Gas............................................. #4240
53A. Pancake Griddle, Fits All Electric............................... #6050
*54. Oven Vent Cap – Fits Gas Top Models ..................... #1246
55. Oven Thermodisk ...................................................... #1507
56. Cooling Fan Thermodisk ........................................... #1509
14. Pilot Light (Element Indicators)
Orange – 110 Volt....................................................... #1511
Red – 220 Volt ............................................................ #1512
15. Casting, Reservoir Door.............................................. #1055
17. Oven Light Assembly.................................................. #1354
18. Oven Rack, Electric & Gas Ovens.............................. #1340
20. Broiler Pan & Grill...................................................... #1338
20B. Convection Roasting Rack.......................................... #1380
21. Oven Door Handle ...................................................... #1515
22. Oven Side Panel (Right or Left).................................. #1043
23. Hidden Bake Element (Under Oven Floor)................. #1366
*23B. Bottom Bake Burner (Gas).......................................... #1254
*23C. Ignitor for Bottom and Top Gas Oven Burner ............ #1258
24. Top Broil/TBake Element (Electric)........................... #1367
*24A. Top Broil Burner (Gas) ............................................... #1260
25. Door Hinge (Right) ...................................................#1336R
25A. Door Hinge (Left)......................................................#1336L
26. Self Clean Latch – Motorized ..................................... #1334
28. Casting, Fire Door....................................................... #1049
29. Casting, Oven Door..................................................... #1047
30. Ash Catch.................................................................... #1037
31. Splashback................................................................... #1093
32. Oven Thermometer (Decorative only) ........................ #1445
33. Handle, Cabinet Door.................................................. #1553
34. Cabinet Door & Hinge ................................................ #1087
35. Cabinet Cresting.......................................................... #1051
gas parts on this list are indicated with *.
Please specify color or plating when ordering parts .
when ordering please give model and serial number
of range.
Parts are available directly from elmira stove
works at 1-800-295-8498.
where can i find the model and
serial number?
Both gas and electric certification plates are located on the
underside of the ash catch (this is the piece that attaches
with three screws to the bottom of the oven door).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts of your range
(2004 & later)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
notes:
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
our factory helP line numBer is:
1-800-295-8498
warranty
Your range is warranted by elmira stove works to be free from defects in material and
workmanship for a period of one year from the date of purchase. Elements, burners and
smooth tops are warranted for five years.
elmira stove works warrants to replace any parts free of charge which become defective
during the period of this warranty. It also warrants to provide fair service labor rates to install
the warranted parts during the first year. Glass, light bulbs, enamel, porcelain coatings and
nickel plating are not covered by the warranty. Warranty is subject to the terms outlined
below.
terms and conditions
This warranty applies only for residential use in the country of purchase. The range must be
properly installed according to this manual and to local building and safety codes. Abuse,
accident, alteration or misuse will void this warranty.
Neither elmira stove works nor the dealer is liable for any damages or claims resulting
from failure of the range or from service delays beyond their control.
Parts repaired or replaced through this warranty are warranted for the balance of the original
warranty period.
This warranty does not cover any cost of making the appliance readily available for service,
and does not cover labor performed at overtime or premium rates.
Purchase Date: ____________________ Store: ______________________
Store Address: __________________________________________________
range model __________________________________
serial number _________________________________
elmira stove works
285 Union Street, Elmira, ON Canada N3B 3P1
Tel: 519 669-1281 Fax: 519 669-1774
E-mail: [email protected]
40
Download from Www.Somanuals.com. All Manuals Search And Download.
|