JVC Stereo Receiver RX D412BUJ User Manual

AUDIO/VIDEO CONTROL RECEIVER

RX-D412B

INSTRUCTIONS

LVT1572-010A

[UJ]

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

We would like to thank you for purchasing one of our JVC products.

Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit,

and retain this manual for future reference.

DCDi technology

Features

Hybrid Feedback Digital Amplifier

DCDi (Directional Correlational Deinterlacing) technology,

developed by Faroudja, eliminates jagged edges generated

in progressive scanning conversion. With DCDi, you can enjoy

RX-D412B features the JVC-exclusive Hybrid Feedback Digital

Amplifier. Premium-grade parts and devices, and special

internal construction assure you will enjoy superior sound.

clear and smooth video images on your display. For RX-D412B,

this function is applied only when the NTSC analog video

signals are transmitted to the receiver.

Compatible with HDMI*

K2 technology

The HDMI (High-Definition Multimedia Interface) is the

standard interface for the next-generation TV. By connecting

the source components, this receiver, and TV with the HDMI

cables, digital video signals and audio signals (including Dolby

Digital, DTS) are transmitted through the cables. You can

transmit digital video signal and audio signal without AD/DA

conversion with easy connection.

K2 technology has been designed to enable natural audio

reproduction, achieving a drastic reduction in digital

distortion and creating original sound ambience with high

precision.

As RX-D412B supports up to HDMI version 1.1, this receiver

can digitally receive 5.1-channel PCM with fs 96 kHz and 2-

channel PCM with fs 192 kHz. (These PCM signals are referred

to as “multi-channel PCM” in this instructions.) You can enjoy

digital sound without deterioration. In addition, this receiver

is compatible with HDCP** (High-bandwidth Digital Content

Protection), and HDCP contents can be viewed if you connect

an HDCP-compatible TV to this receiver.

Precautions

Power sources

• When unplugging the receiver from the wall outlet, always

pull the plug, not the AC power cord.

• Do not handle the AC power cord with wet hands.

• If you are not going to operate the receiver for an extended

period of time, unplug the AC power cord from the wall

outlet.

* HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing LLC.

**HDCP is the abbreviation of “High-bandwidth Digital

Content Protection,” and is the high-reliable copy control

technology licensed by Digital Content Protection, LLC.

Ventilation

The seven high power amplifiers built in this receiver will

generate heat inside the cabinet.

For safety, observe the following carefully:

• Make sure there is good ventilation around the receiver.

Poor ventilation could overheat and damage the receiver.

• Do not block the ventilation openings or holes. (If the

ventilation openings or holes are blocked by a newspaper or

cloth, etc., the heat may not be able to get out.)

7.1 channel DAP (Digital Acoustic Processor)

Sound field simulation technology allows precise ambience

recreation of existing theaters and halls. Thanks to the high-

performance DSP (Digital Signal Processor) and high-capacity

memory, you can enjoy 7.1-channel surround by playing

2-channel or multi-channel software.

Others

• Should any metallic object or liquid fall into the receiver,

unplug the receiver and consult your dealer before

operating any further.

• Do not use this receiver in a bathroom or places with water.

• Do not place any containers filled with water or liquids (such

as cosmetics or medicines, flower vases, potted plants, cups,

etc.) on the top of this receiver.

Precise Surround Setup

Precise Surround Setup is a newly-developed JVC solution for

quick, easy and systematic optimization of surround sound.

By using Precise Surround Setup, you can enjoy the best

possible surround performance. Precise Surround Setup

measures the listening environment accurately with the

dedicated earphone-type microphones and adjusts the

speaker settings automatically.

• Do not disassemble the receiver since there are no user

serviceable parts inside.

CC (Compression Compensative) Converter

If anything goes wrong, unplug the AC power cord and

consult your JVC dealer.

CC Converter eliminates jitter and ripples, achieving a drastic

reduction in digital distortion by processing the digital music

data in 24 bit–quantization and by expanding the sampling

frequency to 128 kHz (for fs 32 kHz signals)/176.4 kHz (for fs

44.1 kHz signals)/192 kHz (for fs 48 kHz signals). By using the

CC Converter, you can obtain a natural sound field from any

source.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic settings .............................................................29

Basic setting items.......................................................................... 29

Operating procedure .................................................................... 30

Setting the speakers...................................................................... 30

Activating the EX/ES/PLIIx setting—EX/ES/PLIIx ................ 32

Selecting the main or sub channel—DUAL MONO ........... 32

Setting bass sound......................................................................... 33

Using the Midnight mode—MIDNIGHT MODE ................... 33

Setting the digital input (DIGITAL IN) terminals—DIGITAL

IN 1/2/3 ....................................................................................... 34

Setting the Audio delay level—AUDIO DELAY.................... 34

Selecting the source for HDMI terminal and COMPONENT

VIDEO jacks—HDMI SELECT/CMPNT SELECT................ 34

Selecting the output video signals—VIDEO OUTPUT....... 34

Table of Contents

Parts identification......................................................3

Getting started ............................................................6

Before installation .............................................................................6

Checking the supplied accessories .............................................6

Putting the batteries in the remote control.............................6

Setting the voltage selector...........................................................6

Connecting the antennas...............................................................7

Connecting the speakers................................................................8

Connecting video components....................................................9

Connecting the power cord........................................................ 14

USB connection............................................................................... 15

Sound adjustments ...................................................35

Basic adjustment items ................................................................ 35

Operating procedure .................................................................... 35

Adjusting the speaker output levels........................................ 36

Adjusting the equalization patterns—D EQ 63Hz/250Hz/

1kHz/4kHz/16kHz.................................................................... 36

Reinforcing the bass—BASS BOOST........................................ 37

Attenuating the input signal—INPUT ATT............................ 37

Adjusting the sound parameters for the Surround/DSP

modes.......................................................................................... 37

Precise Surround Setup ............................................16

Setting the speakers automatically.......................................... 16

Troubleshooting for Precise Surround Setup....................... 19

Creating realistic sound fields..................................39

Reproducing theater ambience ................................................ 39

Introducing the Surround modes............................................. 39

Introducing the DSP modes ....................................................... 41

Using the Surround/DSP modes............................................... 42

Activating the Surround/DSP modes...................................... 43

Basic operations ........................................................20

Turn on the power.................................................................. 20

Select the source to play ...................................................... 20

Adjust the volume .................................................................. 21

Selecting the video and audio input settings ...................... 21

Selecting the digital decode mode.......................................... 22

Turning off the sounds temporarily......................................... 22

Changing the display brightness.............................................. 22

Turning off the power with the Sleep Timer ........................ 23

Making sounds natural................................................................. 23

AV COMPU LINK remote control system .................45

Operating other JVC products..................................47

Operating other manufacturers’ products..............49

Troubleshooting........................................................52

Specifications.............................................................54

FM/AM tuner operations...........................................24

Setting the AM tuner interval spacing.................................... 24

Tuning in to stations manually.................................................. 24

Using preset tuning ....................................................................... 24

Selecting the FM reception mode............................................ 25

XM Satellite Radio operations..................................26

Preparation ....................................................................................... 26

Listening to the XM Satellite Radio.......................................... 26

Using preset tuning ....................................................................... 27

Changing the channel information ......................................... 28

Download from Www.Somanuals.com. All Manuals Search And Download.

7Remote control

See pages in parentheses for details.

Parts identification

MUTING button (22)

Standby/on buttons (16, 20, 47 – 51)

AUDIO, DVR/DVD , VCR , DBS/CATV

TV/SIRIUS

Source selecting buttons (20, 24, 26, 47 – 51)

DVR/DVD, VCR, DBS, TV, USB, XM, FM/AM, SIRIUS

TV VOL (volume) +/– button (47, 49)

CHANNEL +/– button (27, 47 – 51)

• Operating buttons for video components (47, 48, 50, 51)

4, 3, ¢, 1, 7, 8, ¡

• Operating buttons for FM/AM tuner (24)

( TUNING, TUNING 9

• Operating buttons for XM Satellite Radio or SIRIUS

Satellite Radio (27, 47)

SELECT*, ( CAT, CAT 9

Operating buttons for DVD recorder or DVD player**

(48, 51)

TOP MENU, MENU, cursor buttons (3, 2, 5, ∞), SET

SURROUND button (44)

TV/VIDEO button (47, 49)

VIDEO INPUT button (21)

AUDIO INPUT button (21)

CC CONVERTER button (23)

Adjusting buttons for Digital Equalizer (36)

D.EQ FREQ, D.EQ LEVEL +/–

DECODE button (22)

Adjusting buttons for speaker and subwoofer output levels

(36)

FRONT L +/–, FRONT R +/–, CENTER +/–, SUBWFR +/–, SURR

L +/–, SURR R +/–, S.BACK L +/–, S.BACK R +/–

VOLUME +/– button (21)

Mode selector (48, 51)

DISPLAY button (28, 47)

• Numeric buttons (25, 27, 47 – 51)

1 – 10, 0, h10, +10/100+

• RETURN button (47)

BAND* button (47)

;

PREV*/FM MODE button (25, 47)

DIRECT button (27)

DIMMER button (22)

MEMORY button (24, 27)

PSS (Precise Surround Setup) button (17)

TEST button (18, 36)

SLEEP button (23)

* For SIRIUS Satellite Radio only

**These buttons can be used for operating a DVD recorder

(JVC products only) or DVD player, with the mode selector

set to “DVR” or “DVD” (see page 48).

To open the cover of the

remote control, push here

then slide downward.

If these buttons do not function normally, use the remote

control supplied with your DVD recorder or DVD player.

Refer also to the manual supplied with the DVD recorder or

DVD player for details.

• When operating a DVD recorder (for JVC products

only), set the mode selector (u) to “DVR.”

• When operating a DVD player, set the mode selector

(u) to “DVD.”

Download from Www.Somanuals.com. All Manuals Search And Download.

See pages in parentheses for details.

Front Panel

STANDBY/ON button and standby lamp (16, 20)

• SET button (20, 30, 35)

• TUNER PRESET button (25, 28)

• SOURCE SELECTOR (20, 25, 26, 28)

• MULTI JOG (25, 28, 30, 35, 44)

MASTER VOLUME control (21)

PHONES jack (21)

CC CONVERTER button (23)

SETTING button (30)

ADJUST button (35)

SURROUND button (44)

HDMI lamp (9, 21)

USB terminal (15)

Source lamps

DVR/DVD, VCR, DBS, TV/SIRIUS, USB, XM, FM/AM

PRECISE SURROUND SETUP MIC jack (16)

Display window (see below)

Remote sensor (6)

Display window

ANALOG indicator (21)

Digital signal format indicators (21, 22, 40, 41)

DIGITAL AUTO, LINEAR PCM,

Signal and speaker indicators (23)

NEO:6 indicator (40)

96/24

DUAL MONO indicator (32)

(

)

AUTO SURR (surround) indicator (43)

HEADPHONE indicator (21, 42)

VIRTUAL SB (surround back) indicator (43)

3D-PHONIC indicator (40, 41)

DSP indicator (41)

PSS (Precise Surround Setup) indicator (17)

CC CONVERTER 1 and CC CONVERTER 2 indicators (23)

FM/AM tuner operation indicators (24)

TUNED, STEREO

DIGITAL EQ indicator (36)

and

indicators (39 – 41)

Main display

AUTO MUTING indicator (25)

C (center).TONE indicator (38)

INPUT ATT (attenuate) indicator (37)

SLEEP indicator (23)

B (bass).BOOST indicator (37)

MIDNIGHT indicator (33)

Frequency unit indicators

MHz (for FM stations), kHz (for AM stations)

Download from Www.Somanuals.com. All Manuals Search And Download.

See pages in parentheses for details.

Rear Panel

Power cord (14)

VIDEO jacks (10 – 13)

VIDEO (composite video) jacks, S-VIDEO jacks

• Input: DBS IN, VCR IN(PLAY), DVR/DVD IN(PLAY)

• Output: VCR OUT(REC), DVR OUT(REC), MONITOR OUT

VOLTAGE SELECTOR (6)

HDMI terminals (9)

VCR(DBS) IN, DVR/DVD IN, MONITOR OUT

COMPONENT VIDEO (Y, PB, PR) jacks (10 – 13)

VCR(DBS) IN, DVR/DVD IN, MONITOR OUT

AUDIO jacks (10 – 13)

• Input: TV/SIRIUS IN, DBS IN, VCR IN(PLAY), DVR/DVD

IN(PLAY)

• Output: VCR OUT(REC), DVR OUT(REC)

DVD MULTI IN jacks (11)

CENTER, SUBWOOFER, SURR–L, SURR–R

SUBWOOFER OUT jack (8)

AV COMPU LINK-III terminals (45)

DIGITAL IN terminals (14)

• Coaxial: 1(DVR/DVD)

• Optical: 2(DBS)

• Optical: 3(VCR)

DIGITAL OUT terminal (14)

XM jack (7)

FM/AM ANTENNA terminals (7)

Speaker terminals (8)

SURROUND BACK SPEAKERS, SURROUND SPEAKERS,

CENTER SPEAKER, FRONT SPEAKERS

Download from Www.Somanuals.com. All Manuals Search And Download.

Putting the batteries in the remote

control

Getting started

Before using the remote control, put two supplied batteries

first.

Before installation

7General precautions

1 Press and slide the battery cover on the

• Be sure your hands are dry.

back of the remote control.

• Turn the power off to all components.

• Read the manuals supplied with the components you are

going to connect.

2 Insert the batteries.

Make sure to match the polarity: (+) to (+) and (–) to (–).

7Locations

3 Replace the cover.

• Install the receiver in a location that is level and protected

from moisture and dust.

If the range or effectiveness of the remote control decreases,

replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell

batteries.

• The temperature around the receiver must be between –5°C

and 35°C.

• Make sure there is good ventilation around the receiver.

Poor ventilation could cause overheating and damage the

receiver.

• Supplied butteries are for initial setup. Replace for

continued use.

CAUTION:

• Leave sufficient distance between the receiver and the TV.

Follow these precautions to avoid leaking or cracking cells:

• Place batteries in the remote control so they match the

polarity: (+) to (+) and (–) to (–).

• Use the correct type of batteries. Batteries that look similar

may differ in voltage.

7Handling the receiver

• Do not insert any metal object into the receiver.

• Do not disassemble the receiver or remove screws, covers,

or cabinet.

• Always replace both batteries at the same time.

• Do not expose batteries to heat or flame.

• Do not expose the receiver to rain or moisture.

• Do not pull on the power cord to unplug the cord. When

unplugging the cord, always grasp the plug so as not to

damage the cord.

• When you are away on travel or otherwise for an extended

period or time, remove the plug from the wall outlet. A small

amount of power is always consumed while the power cord

is connected to the wall outlet.

When using the remote control, aim the remote control

directly at the remote sensor on the front panel.

Remote sensor

The receiver has a built-in cooling fan which operates

while the receiver is turned on. Be sure to leave enough

ventilation to obtain sufficient cooling effect.

CAUTION:

Do not connect the AC power cord until all other connections

have been made.

Setting the voltage selector

Before connections, always do the following first if necessary.

Select the correct voltage in VOLTAGE

SELECTOR on the rear of the receiver by

using a screw driver.

Checking the supplied accessories

• Check to be sure if the voltage mark is set to the voltage for

your area where this unit plugs in.

Voltage mark

Check to be sure you have all of the following supplied

accessories. If anything is missing, contact your dealer

immediately.

• Remote control (× 1)

• Batteries (× 2)

• AM loop antenna (× 1)

• FM antenna (× 1)

• Dedicated earphone-type microphones (× 1)

• AC plug adapter (× 1)

• Core filter (× 1)

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the antennas

Do not connect the AC power cord until all other connections have been made.

7Connecting FM and AM antennas

If FM reception is poor, connect an

outdoor FM antenna (not supplied).

AM loop antenna (supplied)

Black

Snap the tabs on the loop

into the slots of the base

to assemble the AM loop

antenna.

White

If AM reception is poor, connect an

FM antenna (supplied)

outdoor single vinyl-covered wire

(not supplied).

NOTES

AM antenna connection

•

If the AM loop antenna wire is covered with vinyl,

remove the vinyl while twisting it as shown on

the right.

Make sure the antenna conductors do not touch

any other terminals, connecting cords and power

cord. This could cause poor reception.

Connect the AM loop antenna (supplied) to the AM LOOP

terminals: Connect the white cord to the AM EXT terminal, and

connect the black cord to the H terminal.

Turn the loop until you have the best reception.

• If the reception is poor, connect an outdoor single vinyl-

covered wire (not supplied) to the AM EXT terminal. Keep

the AM loop antenna connected.

FM antenna connection

Connect the supplied FM antenna to the FM 75 Ω COAXIAL

terminal as a temporary measure.

Extend the supplied FM antenna horizontally.

• If the reception is poor, connect an outdoor FM antenna

(not supplied). Before attaching a 75 Ω coaxial cable with a

connector, disconnect the supplied FM antenna.

7Connecting the XM Passport System (XM Passport and XM Passport Home Dock)*

To enjoy XM Satellite Radio, connect the XM Passport System (not supplied) to the receiver.

* You can also use the conventional XM Connect and Play Digital Antenna (not supplied) for the receiver.

XM Passport (not supplied)

XM Passport Home Dock (not supplied)

NOTE

For the best reception:

– Place the XM Passport Home Dock antenna near a south-facing

window or where “Channel 1” can be heard clearly (see page 26).

– Make sure there is no obstruction between the XM Passport Home

Dock antenna and the sky.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the speakers

Do not connect the AC power cord until all other connections have been made.

7Speaker Layout Diagram

Powered

subwoofer (SW)

Left surround back

speaker (SBL)*

Center speaker (C)

Right surround

back speaker (SBR)

Right surround speaker (SR)

Right front

speaker (R)

Left front

speaker

(L)

Left surround speaker (SL)

SBL (SB*)

SBR

CAUTIONS:

To connect the surround speakers and the surround back

speakers

• Use speakers with the SPEAKER IMPEDANCE indicated by

the speaker terminals (6 Ω – 16 Ω).

• DO NOT connect more than one speaker to one speaker

terminal.

7Connecting the speakers

Turn off all components before making connections.

1 Cut, twist and remove the insulation at

To connect the center speaker and the front speakers

the end of each speaker cord.

2 Open the terminal (1), then insert the

speaker cord (2).

• For each speaker, connect the (+) and (–) terminals on

the rear panel to the (+) and (–) terminals marked on the

speakers.

3 Close the terminal.

* When using a single speaker for the surround back

speaker

1 Cut, twist and remove the insulation at

the end of each speaker cord.

You can enjoy the surround sound by one surround back

speaker. When using one surround back speaker,

– set “S BACK OUT” to “1SPK” (see page 31) and

– connect the surround back speaker to the left surround

back speaker terminal. (No sound comes from the

speaker if you connect it to the right surround back

speaker terminal.)

2 Turn the knob counterclockwise.

3 Insert the speaker cord.

• For each speaker, connect the (+) and (–) terminals on

the rear panel to the (+) and (–) terminals marked on the

speakers.

4 Turn the knob clockwise.

7Connecting the powered subwoofer

By connecting a subwoofer, you can enhance the bass or

reproduce the original LFE signals recorded in digital software.

Connect the input jack of a powered subwoofer to the

SUBWOOFER OUT jack on the rear panel, using a cord with

RCA pin plugs (not supplied).

• Refer also to the manual supplied with your subwoofer.

After connecting all the speakers and/or subwoofer, perform

Precise Surround Setup to adjust the speaker settings

automatically (see pages 16 to 19).

NOTE

You can place a subwoofer wherever you like since bass sound is non-

directional. Normally place it in front of you.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting video components

Do not connect the AC power cord until all other connections have been made.

7HDMI connection

IMPORTANT:

The HDMI video signals from the HDMI terminals are transmitted only through the HDMI MONITOR OUT terminal.

Therefore, you cannot view the playback picture on the TV:

– when the TV is connected to the receiver through the VIDEO jack (MONITOR OUT), S-VIDEO jack (MONITOR OUT), or

COMPONENT VIDEO jacks (MONITOR OUT) and

– when a playing video component is connected to the receiver through the HDMI terminal—VCR(DBS) IN or DVR/DVD IN as

well.

Turn off all components before making connections.

• When you connect the components, refer also to their manuals.

DVD recorder or

DVD player

HDMI cables

(not supplied)

VCR (or DBS tuner)

Converting video signals into HDMI signals

This receiver can convert composite video, S-video, and component video signals into HDMI signals and transmit the

converted signals through the HDMI MONITOR OUT terminal. To use this function, you need to make the following procedure

beforehand:

Connect your TV and this receiver with the HDMI cable.

Set the video output setting (see page 34) to “HDMI.”

Set the video input setting (see page 21) according to the connection method for each video component.

NOTES

•

When playing back audio and video with the HDMI connection, the HDMI lamp on the front panel is lit.

Select “HDMI” for the audio input setting (see page 21) when you enjoy sound with the HDMI connection.

With input video signals converted into HDMI signals, the playback picture may be distorted when you change the playback mode (fast-

forward, rewind, or pause, for example).

•

When connecting a VCR or DBS to the HDMI VCR(DBS) IN terminal, set the HDMI select setting (see page 34) correctly according to the

equipment you connect. If you do not, you cannot view the playback picture on the TV.

By using an HDMI-DVI conversion cable, you can connect the source components or the TV with DVI output. When connecting those

components or TV, change the audio input setting to other than “HDMI.” (See page 21.)

This receiver is compatible with standard video formats. If non-standard video formats are coming in, the picture may not appear properly on

TV.

•

The picture on the TV may not be the same aspect ratio as the ratio set on the source components.

HDMI (High-Definition Multimedia Interface) is an interface which makes it possible to transmit digital audio and video signals with one cable.

However, when connecting a TV to this receiver with an HDMI cable, the sound coming into this receiver is not transmitted to the speakers of

the TV. You can enjoy sound only from the speakers connected to this receiver.

•

When connecting a TV to the receiver with an HDMI cable, the following may cause noise or interrupt the sound and picture:

– Turning a source component on or off

– Changing the audio or video input setting of this receiver frequently

In this case, turn the receiver off, then turn it on again.

•

When enjoying multi-channel PCM sound and selecting “HDMI” for the audio input setting (see page 21), some functions are not available. See

page 11 for details.

When you enjoy HDCP contents, sound and picture may not be transmitted to the speakers and TV for a few seconds in the beginning for

confirmation.

Download from Www.Somanuals.com. All Manuals Search And Download.

7Audio/video connection

In addition to the HDMI terminals, this receiver is equipped

with three video terminals—composite video, S-video, and

component video terminals, and two audio jacks—analog

discrete 5.1 channel audio input jacks (DVD MULTI IN) and

stereo audio jacks.

DO NOT use a TV through a VCR or a TV with a built-in

VCR; otherwise, the picture may be distorted.

CAUTION:

If you connect a sound-enhancing device such as a graphic

equalizer between the source components and this receiver,

the sound output through this receiver may be distorted.

• If your video components have S-video (Y/C-separation)

and/or component video (Y, PB, PR) jacks, connect them

using an S-video cable (not supplied) or component video

cable (not supplied). By using these terminals, you can get a

better picture quality in the order:

If your video components have AV COMPU LINK terminals

See also page 45 for detailed information about the

connection and the AV COMPU LINK remote control system.

Component > S-video > Composite

IMPORTANT:

* When connecting the TV to the receiver through the HDMI

MONITOR OUT terminal and selecting “HDMI” for the video

output setting, you can view the playback picture on the TV.

The video signals from one type of these input jacks are

transmitted only through the video output jacks of the

same type. Therefore, if a recording video component and

a playing video component are connected to the receiver

through the video terminals of different type, you cannot

record the picture. In addition, if the TV and a playing video

component are connected to the receiver through the video

terminals of different type, you cannot view the playback

picture on the TV.*

Do not connect the AC power cord until all other connections have been made.

Connecting a DVD recorder or DVD player with its stereo output jacks:

Turn off all components before making connections.

• When you connect the components, refer also to their manuals.

: signal flow

Component video cable (not supplied)

Green

Blue

Red

DVD recorder or DVD player

White

Red

Stereo audio cable

(not supplied)

Red

White

Composite video cable

(not supplied)

S-video cable (not supplied)

Composite video cable (not supplied)

NOTES

To component video output

•

Select the audio and video input setting according to the

connection method. See page 21 for details.

• Connect Y, PB, and PR correctly.

To left/right audio channel output

‰

You can enjoy digital sound if using a digital coaxial or optical

cable. When shipped from the factory, the digital coaxial terminal—

DIGITAL IN 1(DVR/DVD) on the rear of the receiver is set for a DVD

recorder and DVD player. For details of digital audio connection, see

page 14.

Only for DVD recorder: To left/right audio channel input

To composite video output

To S-video output

Only for DVD recorder: To S-video input

Only for DVD recorder: To composite video input

Download from Www.Somanuals.com. All Manuals Search And Download.

Do not connect the AC power cord until all other connections have been made.

Connecting a DVD recorder or DVD player with its analog discrete output jacks (DVD MULTI IN):

If your DVD recorder or DVD player has analog 5.1 channel output jacks, use the connection below. When a DVD-Audio disc is

played back, the original high-quality multi-channel sounds can be reproduced by using this connection.

Turn off all components before making connections.

• When you connect the components, refer also to their manuals.

: signal flow

Green

Component video cable (not supplied)

Blue

Red

Monaural audio cable (not supplied)

White

Red

Stereo audio cable

(not supplied)

DVD recorder or

DVD player

Monaural audio cable

(not supplied)

White

Red

Stereo audio cable

(not supplied)

Red

White

Composite video cable

(not supplied)

S-video cable (not supplied)

Composite video cable (not supplied)

To left/right surround channel audio output

Only for DVD recorder: To left/right front channel audio

input

To composite video output

To center channel audio output

To component video output

• Connect Y, PB, and PR correctly.

To subwoofer output

To S-video output

Only for DVD recorder: To S-video input

Only for DVD recorder: To composite video input

‰

To left/right front channel audio output

When you enjoy the sound recorded in DVD-Audio...

You can enjoy the sound recorded in DVD-Audio with either

analog or digital methods.

NOTES

•

When selecting “A MULTI” for the audio input setting and using

the headphones, you can listen to the front channel sounds (left

and right) only. The 3D HEADPHONE mode (see page 42) is not

available.

When selecting “A MULTI” for the audio input setting or when

multi-channel PCM signals (see page 41) are coming in with

selecting “HDMI” for the audio input setting, the following items

are not available:

– With analog method:

1.Connect your DVD recorder or DVD player to this

receiver according to the diagram above.

2.Select “A MULTI” for the audio input setting. (See page

21.)

– With digital method:

– Precise Surround Setup (see pages 16 to 19)

– Decode mode (see page 22)

– CC Converter (see page 23)

1.Connect your DVD recorder or DVD player and TV to this

receiver with the HDMI cables. (See page 9.)

2.Select “HDMI” for the audio input setting. (See page 21.)

– EX/ES/PLllx (see page 32)

– Dual Mono (see page 32)

– Subwoofer output (see page 33)

– Crossover frequency (see page 33)

– Low frequency effect attenuator (see page 33)

– Midnight mode (see page 33)

– Digital equalization patterns (see page 36)

– Bass Boost (see page 37)

– Input attenuator mode (see page 37)

– Sound parameters for Surround/DSP modes (see pages 37 and

38)

– Surround/DSP mode selection (see page 44)

The audio delay level setting (see page 34) does not take effect

when selecting “A MULTI” for the audio input setting.

When you enjoy the sound recorded in DVD-Audio through the

HDMI connection, use a DVD recorder or DVD player compatible

with HDMI version 1.1.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Do not connect the AC power cord until all other connections have been made.

Turn off all components before making connections.

• When you connect the components, refer also to their manuals.

Connecting a VCR:

: signal flow

Component video cable (not supplied)

Green

Blue

Red

VCR

White

Red

Stereo audio cable

(not supplied)

Red

White

Composite video cable

(not supplied)

S-video cable (not supplied)

Composite video cable (not supplied)

NOTES

To component video output

•

Select the audio and video input settings according to the connection method. See page 21 for

details.

When connecting a VCR to the COMPONENT VIDEO jacks, select “VCR” for the COMPONENT

select setting (see page 34); otherwise, the following occurs:

• Connect Y, PB, and PR correctly.

To left/right audio channel output

To left/right audio channel input

To composite video output

To S-video output

‰

– You cannot view the playback picture on the TV.

– The AV COMPU LINK remote control system (see pages 45 and 46) cannot operate properly.

You can enjoy digital audio if using a digital coaxial or optical cable. When shipped from the

factory, the digital optical terminal—DIGITAL IN 3(VCR) on the rear of the receiver is set for a

VCR. For details of the digital audio connection, see page 14.

•

To S-video input

To composite video input

Connecting a SIRIUS Satellite Radio

White

Red

Stereo audio cable (not supplied)

SIRIUS Satellite Radio

NOTES

•

To connect KT-SR2000 (JVC SIRIUS Satellite Radio) to this receiver, it is required to separately purchase KS-K6013 Home Docking Kit.

You cannot use a digital audio cable (coaxial or optical) to connect a SIRIUS Satellite Radio to this receiver.

After connecting a SIRIUS Satellite Radio to the TV/SIRIUS IN jacks, change the source name to “SIRIUS.” See page 20 for details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Do not connect the AC power cord until all other connections have been made.

Turn off all components before making connections.

• When you connect the components, refer also to their manuals.

: signal flow

Connecting a DBS tuner:

Component video cable (not supplied)

Green

Blue

Red

White

Red

Stereo audio cable (not supplied)

DBS tuner

Composite video cable

(not supplied)

S-video cable (not supplied)

NOTES

To left/right audio channel

output

To component video output

• Connect Y, PB, and PR

correctly.

To composite video output

To S-video output

•

Select the audio and video input setting according to the connection method. See page 21 for

details.

When connecting a DBS tuner to the COMPONENT VIDEO jacks, select “DBS” for the COMPONENT

select setting (see page 34); otherwise, you cannot view the playback picture on the TV.

You can enjoy digital sound if using a digital coaxial or optical cable. When shipped from the

factory, the digital optical terminal—DIGITAL IN 2(DBS) on the rear of the receiver is set for a DBS

tuner. For details of digital audio connection, see page 14.

Connecting a TV:

Connect the TV to the appropriate MONITOR OUT jacks to view the playback picture from any other connected video

components.

: signal flow

Green

Component video cable (not supplied)

Blue

Red

Stereo audio cable

White

(not supplied)

Red

S-video cable (not supplied)

Composite video cable (not supplied)

NOTES

To component video input

•

Select the audio input setting according to the connection method. See page 21 for

details.

You can enjoy digital sound if using a digital coaxial or optical cable. For details of the

digital audio connection, see page 14.

• Connect Y, PB, and PR correctly.

To left/right audio channel output

To S-video input

To composite video input

Select “OTHER” for the video output setting (see page 34).

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital output terminal:

You can connect any digital components which have an

optical digital input terminal.

7Digital audio connection

This receiver is equipped with three DIGITAL IN terminals—

one digital coaxial terminal and two digital optical terminals—

and one DIGITAL OUT terminal.

To reproduce the digital sound, use the digital audio

connection in addition to the analog audio connection

methods described on pages 10 to 13.

Digital coaxial cable (not supplied)

Digital optical cable (not supplied)

Turn off all components before making connections.

• When you connect the components, refer also to their

manuals.

Connecting digital recording equipment to the

DIGITAL OUT terminal enables you to perform

digital-to-digital recording.

Digital input terminals:

NOTES

•

The digital signal format transmitted through the DIGITAL OUT

terminal is the same as that of the input signal. For example, when

the DTS signals are input, the DTS signals are transmitted.

The digital signal coming through the USB terminal, HDMI input

terminal and XM jack cannot be output from the DIGITAL OUT

terminal.

When the component has a digital coaxial output

terminal, connect it to the 1(DVR/DVD) terminal, using a

digital coaxial cable (not supplied).

Connecting the power cord

When all the audio/video connections have been made,

connect the AC power plug to the wall outlet. Make sure that

the plugs are inserted firmly.

• The standby lamp lights in red.

When the component has a digital optical output

terminal, connect it to the 2(DBS) or 3(VCR) terminal,

using a digital optical cable (not supplied).

CAUTIONS:

• Do not plug in before setting the VOLTAGE SELECTOR

switch on the rear of the receiver and all connection

procedures are complete.

Before connecting a digital optical

cable, unplug the protective plug.

• Do not touch the power cord with wet hands.

• Do not alter, twist or pull the power cord, or put anything

heavy on it, which may cause fire, electric shock, or other

accidents.

• If the cord is damaged, consult a dealer and have the power

cord replaced with a new one.

NOTES

•

When shipped from the factory, the DIGITAL IN terminals have been

set for use with the following components:

– 1(DVR/DVD): For DVD recorder or DVD player

– 2(DBS): For DBS tuner

– 3(VCR): For VCR

If you connect the components, change the digital input (DIGITAL

IN) terminal setting correctly. See “Setting the digital input (DIGITAL

IN) terminals—DIGITAL IN 1/2/3” on page 34.

Select “DIGITAL” for the audio input setting (see page 21).

NOTES

•

Keep the power cord away from the connecting cables and the

antennas. The power cord may cause noise or screen interference.

The preset settings such as preset channels and sound adjustment

may be erased in a few days in the following cases:

– When you unplug the power cord.

– When a power failure occurs.

•

If the wall outlet does not match the AC plug, use the supplied AC

plug adapter.

When you unplug the power cord with the receiver on and connect

the power cord again, the receiver enters standby mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

5 Check if the drivers are correctly

USB connection

installed.

This receiver is equipped with a USB terminal on the front

panel. You can connect your PC to this terminal and enjoy

sound reproduced through your PC.

1.Open the Control Panel on your PC:

Select [Start] = [Control Panel].

2.Select [System] = [Hardware] = [Device Manager] =

[Sound, video and game controllers] and [Universal

Serial Bus controllers].

When you connect your PC for the first time, follow the

procedure below.

• Remember you cannot send any signal or data to your PC

from this receiver.

• The following window appears, and you can check if the

drivers are installed.

IMPORTANT:

Check if your PC equipped with the CD-ROM drive is running

on Windows® 98 SE*, Windows® Me*, Windows® 2000*, or

Windows® XP* and prepare its CD-ROM.

7How to install the USB drivers

The following procedure is described using the English

version of Windows® XP*. If your PC is running on a different

version or language of operating system, the windows shown

on your PC monitor will differ from the ones used in the

following procedure.

See pages 20 and 21 for the operations of the receiver.

1 Turn on your PC.

• If the PC has been turned on, quit all the applications

now running.

Now your PC is ready for playback through the USB

connection.

2 Turn on the receiver, and select the

After installation is completed, you can use your PC as the

playback source. The PC automatically recognizes the receiver

whenever the receiver is connected by a USB cable and turned

on.

• When not using the PC as the playback source, disconnect

the USB cable from the receiver.

source as “USB.”

3 Set the volume to minimum.

IMPORTANT:

Always set the volume to “0” when connecting or

disconnecting the other equipment.

To play back sounds on the PC, refer to the manual supplied

with the sound reproduction application installed in the PC.

If no sound comes from the speakers, check the following:

– Select “USB” as the source.

– Connect the USB cable correctly.

– Check the receiver is recognized by the PC properly (see

above).

4 Connect the receiver to the PC using a

USB cable (not supplied).

• Use “USB series A plug to B plug” cable when

connecting.

– Check the playback software is compatible with the PC.

– Open the Control Panel on your PC, select [Sounds and

Audio Devices] = [Audio] tab = [Sound playback] =

[Default device], and check [Default device] is set to [USB

Audio DAC].

NOTES

•

DO NOT turn off the receiver or disconnect the USB cable while

installing the drivers and while your PC is recognizing the receiver.

Use a USB cable (version 1.1 or later). Recommended cord length is

less than 1.5 m.

If your PC does not recognize the receiver, disconnect the USB cable

and connect it again. If it does not work yet, restart Windows®*.

The installed drivers can be recognized only when the USB cable is

connected between the receiver and your PC.

USB cable

(not supplied)

The sound may not be played back correctly—interrupted or

degraded—due to your PC settings and PC specifications.

The USB drivers are installed automatically.

• If the USB drivers are not installed automatically, install

the USB drivers by following the instructions on the PC

monitor.

* Microsoft®, Windows® 98 SE, Windows® Me, Windows® 2000,

and Windows® XP are registered trademarks of Microsoft

corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

7Before starting Precise Surround Setup

• Connect all of your speakers and subwoofer correctly and

confirm their position.

Precise Surround

Setup

• When subwoofer has a built-in volume and crossover

frequency controls, adjust them as follows:

– Set the volume level to the medium.

– Set the crossover frequency to the highest level.

• Precise Surround Setup is not available in the following

cases:

– While headphones are connected

– When selecting “A MULTI” for the audio input setting (see

page 11)

– When multi-channel PCM signals (see page 41) are coming

in with selecting “HDMI” for the audio input setting (see

page 11)

• Do not block between the earphone-type microphones and

speakers while the microphones are picking up test tones

from the speakers.

By using Precise Surround Setup, you can optimize the

speaker settings easily, quickly and systematically without

troublesome adjustments.

To obtain the best possible sound effect from the Surround/

DSP modes, set up the speaker and subwoofer information

after all the connections are completed.

• If the microphone cord is not long enough to make a

connection between the receiver and your listening

position, use a stereo extension cord (not supplied).

– You cannot get correct results with a monaural extension

cord.

Setting the speakers automatically

Precise Surround Setup detects the sound from the speakers

to measure your listening environment with dedicated

earphone-type microphones (supplied), and automatically

adjusts the following in less than 1 minute:

• Speaker size*

CAUTION:

Be sure that loud test tones will be generated from

speakers during Precise Surround Setup.

• The volume of test tones is not adjustable.

• Speaker distance*

• Speaker output level*

• Crossover frequency*

• Frequency response

7Operating procedure

1 ^{Plug the dedicated earphone-type}

microphones into the PRECISE

SURROUND SETUP MIC jack.

The receiver generates test tones from each

speaker and picks them up with dedicated

earphone-type microphones.

• Keep the connection until Precise Surround Setup is

completed.

The microphones feedback the test

tones to the receiver.

Dedicated earphone-type microphones (supplied)

2 Press STANDBY/ON (or AUDIO on

* You can also adjust the settings manually. (See pages 29 to

31, and 33.)

the remote control) to turn the power on.

• Set the volume level to the medium or lower turning the

MASTER VOLUME control (see page 21).

STANDBY/ON button

MASTER VOLUME control

Download from Www.Somanuals.com. All Manuals Search And Download.

A test tone comes out of the left and right front speaker

and subwoofer with the volume of the tone increasing

gradually, then Precise Surround Setup starts detecting

the speaker and subwoofer information.

3 Put on the microphones.

• Insert the microphone with “L” into your left ear, the

microphone with “R” your right ear.

• When starting Precise Surround Setup, the muting mode

and Dimmer are automatically canceled.

Example:

• “MEASURING 1” flashes on the display.

Microphone with “L”

Current speaker*¹

*¹When the current speaker is the right or left surround

back speaker, two surround back speaker indicators (

light up at a time.

)

A test tone comes out of each speaker in the following

order, then the microphones pick up the test tones and

feedback it to the receiver:

4 Take your usual listening position with

the microphones and the remote control.

FL (Left front speaker) = C (Center speaker) = FR

(Right front speaker) = SR (Right surround speaker)

= SBR (Right surround back speaker) = SBL (Left

surround back speaker) = SL (Left surround speaker)

= SW (Subwoofer)

• Do not touch the microphones while the microphones

are picking up the test tones.

‘

The receiver generates test tones again.

Precise Surround Setup starts detecting, adjusts the

sound output level from each speaker, and corrects the

frequency response of each speaker.

• “MEASURING 2” flashes on the display.

‘

When Precise Surround Setup is completed, “COMPLETE”

appears and the PSS indicator lights up on the display.

CAUTION:

PSS indicator

Keep quiet so that Precise Surround Setup can detect test

tones properly.

5 Press and hold PSS on the remote control

for about 4 seconds until “PSS START”

starts flashing on the display.

‘

An optimized test tone comes out of each speaker so that

you can confirm the results of Precise Surround Setup, and

the corrected frequency response of each speaker appears

on the display at the same time.

PSS

• See “Checking the frequency responses corrected

by Precise Surround Setup” on page 18 about the

frequency responses on the display.

‘

The receiver automatically returns to the normal operation

mode after all the test tones have been output from the

speakers.

• If Precise Surround Setup is not completed

properly...

An error message will appear on the display.

In such a case, see “Troubleshooting for Precise

Surround Setup“ on page 19.

Continued on the next page

Download from Www.Somanuals.com. All Manuals Search And Download.

7Checking the frequency responses corrected

6 Unplug the earphone-type microphones.

• When unplugging the microphones, pull on the plug,

not the cord itself.

by Precise Surround Setup

You can check the current settings of the frequency responses

with test tones from speakers and the indications on the

display when the frequency optimizing function is activated.

NOTES

•

Do not press any buttons on the remote control or the front panel

of the receiver during Precise Surround Setup; otherwise, the

receiver stops setting and returns to the normal operation mode.

– After “COMPLETE” is displayed, the Precise Surround Setup results

are applied to the speaker settings.

From the remote control ONLY:

1 Press TEST to check the frequency

•

The speaker size measured by Precise Surround Setup may be

different from that of the manual setting recommendation (see

page 30). Precise Surround Setup measures the speaker size not

only by the cone speaker size but also by the other speaker features.

There may be a case that the receiver fails to detect subwoofer

and does not activate it (no optimized test tone comes out of the

subwoofer).

response of each speaker on the display.

In such a case, set the volume level of the subwoofer higher and

perform Precise Surround Setup again.

TEST

•

When you change your listening environment, such as speakers,

speaker position, your listening position or so, perform Precise

Surround Setup again to optimize the speaker settings.

Depending on the listening environment, Precise Surround Setup

may not measure the speaker settings accurately. In such a case,

adjust the settings manually. See pages 29 to 31, and 33.

The supplied earphone-type microphones cannot be used as

headphones.

• A test tone also comes from each speaker in the following

order:

•

FL (Left front speaker) = C (Center speaker) = FR (Right

front speaker) = SR (Right surround speaker) = SBR

(Right surround back speaker)* = SBL (Left surround back

speaker)* = SL (Left surround speaker) = SW (Subwoofer)

* When using a single speaker for the surround back

speaker, the test tone comes out of “SB (Surround back

speaker)” instead of “SBR” and “SBL.”

When the AV COMPU LINK remote control system works during

Precise Surround Setup, this receiver stops setting and returns to

the normal operation mode.

7Turning the frequency optimizing function

off

• The frequency response of each speaker appears on the

display as follows:

After performing Precise Surround Setup, the receiver

optimizes the frequency response for each speaker.

You can turn the frequency optimizing function off.

EX. 1: When a test tone comes from the left front speaker

Current speaker

Frequency response

Press PSS to turn the frequency optimizing

function off.

+9 dB

Optimizing level

–9 dB

• Each time you press the button, the frequency optimizing

function alternates between on and off.

When the function is activated, the PSS indicator is lit.

Low

Frequency

High

NOTE

EX. 2: When a test tone comes from the subwoofer

This function is not available:

– Until Precise Surround Setup has been completed at least once;

otherwise, “NO PSS” appears on the display.

– When selecting “A MULTI” for the audio input setting (see page 11).

– When multi-channel PCM signals (see page 41) are coming in with

selecting “HDMI” for the audio input setting (see page 11).

Crossover

frequency

80 Hz

200 Hz

2 Press TEST again to stop the test tone.

NOTE

While the PSS indicator is off, pressing TEST generates test tones

without showing frequency responses. See page 36.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting for Precise Surround Setup

When problems occur, a message appears on the display during Precise Surround Setup. In this case, refer to the following

solution, then perform Precise Surround Setup again.

• To restart Precise Surround Setup, press PSS on the remote control; however, when you have turned the receiver off for the

solution, start from step 2 again.

Error message

Possible cause

Solution

Headphones are connected to the PHONES jack. Unplug the headphones.

The dedicated earphone-type microphones are

not connected correctly.

Plug the microphones into the PRECISE SURROUND

SETUP MIC jack on the front panel firmly.

There is some background noise.

• Restart in a quiet environment.

• If some electronic equipment is used near the

listening position, turn off the equipment such as

air conditioners, etc.

The speaker is too close to the listening position. Place the speakers farther from the listening position.

• Any of the front speakers is not connected or its • Check the left and right front speakers connections.

connection is loose.

• The microphone connection is loose.

• Plug the microphones into the PRECISE SURROUND

SETUP MIC jack on the front panel firmly.

The built-in volume control of the powered

subwoofer is set to too high.

Set the volume level of the subwoofer lower.

The speaker is too far from the listening position Adjust the speaker position and angle.

or the speaker angle is inappropriate.

The speaker is too far from the listening position. The speaker distance is adjustable up to 9 m (30 ft).

Place the speaker within the adjustable range from

the listening position.

• When the size of the front speakers is small, no • Check the connection of the subwoofer and turn it

subwoofer is detected.

• The receiver might have failed to detect

subwoofer.

on, or replace the front speakers with larger ones.

• Set the volume level of the subwoofer higher.

The front speakers are smaller than the surround • Change the front speakers with the larger ones

speakers.

than the surround speakers.

• Change the surround speakers with the smaller

ones than the front speakers.

The surround speakers are smaller than the

surround back speakers.

• Change the surround speakers with the larger ones

than the surround back speakers.

• Change the surround back speakers with the

smaller ones than the surround speakers.

The right-and-left front speaker size is

unproportioned.

Rearrange the front speakers as their size is

proportioned.

• Any of the surround speakers is not connected • Check the connection of the surround speakers.

or its connection is loose.

• The right-and-left surround speaker size is

unproportioned.

• Rearrange the surround speakers as their size is

proportioned.

* • The left surround back speaker is not connected • Check the connection of the left surround back

or its connection is loose even though the right

surround back speaker is detected.

speaker.

• When using a single speaker as the surround

back speaker, connect it to the left surround back

speaker terminal (see page 8).

• The right-and-left surround back speaker size is • Rearrange the surround back speakers as their size

unproportioned. is proportioned.

Warning message

Possible cause

Solution

The polarity of the speaker connection is wrong. Match the polarity of the speaker terminals (see page

8).

* The signal indicator of the corresponding speaker lights up with the error/warning message.

NOTES

•

Before making speaker connections, turn the receiver off and unplug the power cord.

If you press the source selecting button for the current source on the remote control while an error message is displayed, the receiver cancels

Precise Surround Setup and returns to the normal operation mode.

•

If multiple errors are detected during Precise Surround Setup, only the most serious error will be shown on the display.

The warning message is displayed for about 10 seconds and the receiver automatically returns to Precise Surround Setup.

Depending on the speaker performance or the listening position, there may be a case that the warning message appears even though speaker

connections are correct. In such a case, there is no effect on the results of Precise Surround Setup.

Download from Www.Somanuals.com. All Manuals Search And Download.

2Select the source to play

Basic operations

On the front panel:

Turn SOURCE SELECTOR until the source

name you want appears on the display.

The source lamp corresponding to the selected source lights

in red.

• As you turn SOURCE SELECTOR, the source changes as

follows:

DVR/DVD Ô VCR Ô DBS Ô TV(SIRIUS)* Ô USB Ô

XM Ô FM Ô AM Ô (Back to the beginning)

Source lamps

DVR/DVD: Select this for the DVD recorder or DVD player.

VCR:

DBS:

TV*:

SIRIUS*:

USB:

XM:

Select this for the VCR.

Select this for the DBS tuner.

Select this for the TV.

Select this for the SIRIUS Satellite Radio.

Select this for the PC component.

Select this for the XM Satellite Radio.

Select this for the FM broadcast.

Select this for the AM broadcast.

FM:

AM:

From the remote control:

Press one of the source selecting buttons.

• For “FM” and “AM,” press FM/AM.

Each time you press the button, the band alternates

between “FM” and “AM.”

NOTE

When you connect a VCR or DBS to the HDMI VCR(DBS) IN terminal

or COMPONENT VIDEO jacks on the rear of the receiver, you need

to select either “VCR” or “DBS” for each terminal according to the

component you connect (see page 34).

1Turn on the power

* Changing the source name of TV/SIRIUS input

Press STANDBY/ON (or AUDIO on the

remote control).

On the front panel ONLY:

The standby lamp goes off and the current source lamp lights

in red.

Press SET when “TV” is selected as the

source.

Current source name appears.

• “ASSIGN SIRIUS” appears on the display for a while.

• To change the source name to “TV,” press SET when “SIRIUS”

is selected as the source. “ASSIGN TV” appears on the display

for a while.

To turn off the power (into standby):

Press

STANDBY/ON (or

AUDIO on the remote control)

again.

The standby lamp lights in red.

NOTES

•

A small amount of power is consumed in standby mode. To turn the

power off completely, unplug the AC power cord.

Turning a source component on before turning the receiver on

may cause a noise or interrupt the sound and picture. In this case,

turn both the source component and the receiver off, then turn the

receiver on before turning the source component on.

Download from Www.Somanuals.com. All Manuals Search And Download.

7Selecting the video input setting

From the remote control ONLY:

3Adjust the volume

To increase the volume, turn MASTER

VOLUME control clockwise (or press

VOLUME + on the remote control).

1 Press one of the source selecting buttons

to select the source you want.

To decrease the volume, turn MASTER

VOLUME control counterclockwise (or press

VOLUME – on the remote control).

• When you adjust the volume, the volume level indication

appears on the display for a while.

2 Press VIDEO INPUT to select the video

input setting.

• Each time you press the button, the input setting

changes as follows. This setting is memorized for each

source.

CAUTION:

Always set the volume to the minimum before starting any

sources. If the volume is set at its high level, the sudden blast

of sound energy can permanently damage your hearing and/

or ruin your speakers.

HDMI = CMPNT (Component) = S (S-Video) =

C (Composite) = (Back to the beginning)

NOTE

The volume level can be adjusted within the range between “0”

(minimum) and “50” (maximum).

For “VCR” and “DBS,” set the HDMI select and COMPONENT select

settings correctly if necessary (see page 34).

7Listening with headphones

7Selecting the audio input setting

From the remote control ONLY:

You can enjoy not only stereo software but also multi-channel

software through the headphones. (Sounds are down-mixed

to the front channels while playing multi-channel software.)

1 Press one of the source selecting buttons

Connect a pair of headphones to the

PHONES jack on the front panel to activate

the HEADPHONE mode.

The HEADPHONE indicator lights up on the display.

• You can also enjoy the Surround/DSP mode through the

headphones—3D HEADPHONE mode (see page 42).

• Disconnecting a pair of headphones from the PHONES jack

cancels the HEADPHONE (or 3D HEADPHONE) mode and

activates the speakers.

to select the source you want.

2 Press AUDIO INPUT to select the audio

input setting.

• Each time you press the button, the audio input setting

changes as follows. This setting is memorized for each

source.

CAUTIONS:

• Be sure to turn down the volume:

– Before connecting or putting on headphones, as high

volume can damage both the headphones and your

hearing.

HDMI = DIGITAL = ANALOG = A MULTI =

(Back to the beginning)

– Before removing headphones, as high volume may output

from the speakers.

• Do not plug headphones into the PRECISE SURROUND

SETUP MIC jack; otherwise, loud tones may come out of the

headphones.

HDMI (for “DVR/DVD,” “VCR” and “DBS”):

Select for the source with HDMI connection. The

receiver automatically detects the incoming

signal format, then the digital signal format

indicator (LINEAR PCM,

, or

96/24) for the detected signal lights up, and the

HDMI lamp on the front panel lights up.

DIGITAL*: Select for the digital input setting. The receiver

automatically detects the incoming signal

NOTES

•

When using the headphones, the speaker settings does not take

effect temporarily.

The supplied earphone-type microphones cannot be used as

headphones.

format, then the digital signal format indicator

(LINEAR PCM,

, or

96/24) for

the detected signal lights up.

ANALOG*: Select for the analog input setting. The ANALOG

indicator lights up on the display.

A MULTI (Only for “DVR/DVD”):

Selecting the video and audio input

settings

Select when connecting a DVD recorder or DVD

player to DVD MULTI IN jacks (see page 11). The

ANALOG indicator lights up on the display.

You need to select the proper video and audio input settings

for each source according to the connection methods on

pages 9 to 14.

* When “TV” is selected as the source, only “DIGITAL” and

“ANALOG” are available.

• In case of digital audio connection using the DIGITAL IN

terminals on the rear of the receiver, you also need to select

the correct digital input terminal (see page 34).

• Once you have made an adjustment, it is memorized for

each source.

Continued on the next page

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

The following digital signal format indicators on the display

indicate what type of signal comes into the receiver. See

pages 39 to 41 for the details of each digital signal format.

•

“HDMI” is selectable only when the video input setting is also set to

“HDMI” (see page 21).

The audio input setting may automatically change if you change the

video input setting to or from “HDMI.” In such a case, make sure that

the appropriate setting is selected.

LINEAR PCM: • Lights up when Linear PCM signal comes

in.

• When the multi-channel PCM signal

comes in, “MULTI CH PCM” appears on

the display for a while.

“DIGITAL” is available for the source which is assigned for “DIGITAL

IN 1,” “DIGITAL IN 2,” or “DIGITAL IN 3.” See page 34 for details.

Initial setting of the video and audio input for each source:

Lights up when Dolby Digital signal comes

in.

• Flashes when “DOLBY DIGITAL” is

selected for any software other than

Dolby Digital.

Lights up when conventional DTS signal

comes in.

• Flashes when “DTS” is selected for any

software other than DTS.

Setting

Video input

Audio input

Source

DVR/DVD

HDMI

DIGITAL

ANALOG

VCR

DBS

—

SIRIUS

USB

—

ANALOG (fixed)

DIGITAL (fixed)

ANALOG (fixed)

Lights up when DTS 96/24 signal comes in.

96/24:

NOTE

—

When “DIGITAL AUTO” cannot recognize the incoming signal, no

digital signal format indicator lights up on the display.

Selecting the digital decode mode

When “HDMI” or “DIGITAL” is selected for the audio input

setting (see page 21), this receiver automatically detects the

incoming digital signal format and sets the digital decode

mode to “DIGITAL AUTO.”

Turning off the sounds temporarily

From the remote control ONLY:

Press MUTING to turn off the sound

through all connected speakers and

headphones.

• The DIGITAL AUTO indicator lights up on the display.

If the following symptoms occur while playing Dolby Digital

or DTS software with “DIGITAL AUTO” selected, follow the

procedure below:

“MUTING” appears on the display and the volume turns off.

• Sound does not come out at the beginning of playback.

• Noise comes out while searching for or skipping chapters or

tracks.

From the remote control ONLY:

To restore the sound, press MUTING again.

• Pressing VOLUME +/– (or turning MASTER VOLUME control

on the front panel) also restores the sound.

Press DECODE to select “DOLBY DIGITAL”

or “DTS.”

• Each time you press DECODE, the digital decode mode

changes as follows:

NOTE

When performing Precise Surround Setup or turning the power off,

muting is automatically canceled.

DIGITAL AUTO = DOLBY DIGITAL = DTS =

(Back to the beginning)

Changing the display brightness

You can dim the display—Dimmer.

• To play back software encoded with Dolby Digital, select

“DOLBY DIGITAL.”

From the remote control ONLY:

• To play back software encoded with DTS, select “DTS.”

Press DIMMER repeatedly.

• Each time you press the button, the display brightness

changes as follows:

NOTES

•

The digital decode mode is fixed to “DIGITAL AUTO” when selecting

“USB” or “XM” as the source.

“DOLBY DIGITAL” or “DTS” is automatically reset to “DIGITAL AUTO”

in the following cases:

DIMMER 1

DIMMER 2

DIMMER 3

Dims the display.

Dims the display more than DIMMER 1.

Turns off the display.

– When you turn off the receiver.

– When you select another source.

– When you change the audio input setting (see page 21).

(Temporarily canceled when you operate the

receiver.)

DIMMER OFF Cancels the Dimmer (normal display).

NOTE

When performing Precise Surround Setup, Dimmer is automatically

canceled.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic adjustment of auto memory

Turning off the power with the Sleep

This receiver memorizes sound settings for each source:

• When you turn off the power

Timer

• When you change the source

You can fall asleep while listening to music—Sleep Timer.

When you change the source, the memorized settings for

the newly selected source are automatically recalled.

The following can be stored for each source:

• Video input setting (see page 21)

• Audio input setting (see page 21)

• CC Converter (see the left column)

• Midnight mode (see page 33)

• Digital equalization patterns (see page 36)

• Bass Boost (see page 37)

From the remote control ONLY:

Press SLEEP repeatedly.

• Each time you press the button, the shut-off time changes

in 10-minute intervals. The SLEEP indicator lights up on the

display.

SLEEP indicator

• Input attenuator mode (see page 37)

• Surround/DSP mode selection (see page 44)

NOTE

10min = 20min = 30min = 40min =50min = 60min

= 70min = 80min =90min = OFF (Canceled) =

(Back to the beginning)

If the source is “FM” or “AM,” you can assign a different setting for

each band.

When the shut-off time comes:

The receiver turns off automatically.

Signal and speaker indicators on the display

Signal indicators

Speaker indicators

To check the remaining time until the shut-off time:

Press SLEEP once.

The remaining time (in minutes) until the shut-off time

appears.

• To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer:

Press SLEEP repeatedly so that “SLEEP OFF” appears on the

display. (The SLEEP indicator goes off.)

• The Sleep Timer is also canceled when you turn off the

receiver.

The signal indicators light up as follows:

• When digital input is selected: Lights up when

the left channel signal comes in.

• When analog input is selected: Always lights up.

• When digital input is selected: Lights up when

the right channel signal comes in.

• When analog input is selected: Always lights up.

Lights up when the center channel signal comes in.

Lights up when the left surround channel signal

comes in.

Making sounds natural

LS:

JVC’s CC (Compression Compensative) Converter eliminates

jitter and ripples, achieving a drastic reduction in digital

distortion by processing the digital music data in 24 bit-

quantization and by expanding the sampling frequency

to 176.4 kHz (for fs 44.1 kHz signals)/192 kHz (for fs 48 kHz

signals) on the front speakers.

RS: Lights up when the right surround channel signal

comes in.

Lights up when monaural surround signal comes in.

By using the CC Converter, you can obtain a natural sound

field from both digital and analog sources.

SB: Lights up when the surround back channel signal

comes in.

• Once you have made an adjustment, it is memorized for

each source.

LFE: Lights up when the LFE channel signal comes in.

NOTES

Press CC CONVERTER repeatedly.

• Each time you press the button, the mode changes as

follows:

•

When “A MULTI” is selected for the audio input setting (see page

21), all the signal indicators except “SB” and “S” light up.

When playing back multi-channel digital sound recorded in DVD-

Audio with HDMI connection (see pages 9 and 21), the signal

indicators may not light up correctly.

CC CNVRTR 1

Select when playing back an analog source

or a digital source with non compressed

digital sound signal (Linear PCM).

The CC CONVERTER 1 indicator lights up on

the display.

The speaker indicators light up as follows:

• The subwoofer indicator (

“SUBWOOFER” is set to “YES.” For details, see page 30.

• The other speaker indicators light up only when the

corresponding speaker is set to “SML (small)” or “LRG

(large),” and also required for the current playback.

) lights up when

CC CNVRTR 2

Select when playing back a source with

compressed digital sound signal (Dolby

Digital or DTS).

The CC CONVERTER 2 indicator lights up on

the display.

CC CNVRTR OFF Select when not using the CC Converter.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuning in to stations manually

FM/AM tuner

operations

From the remote control ONLY:

1 Press FM/AM to select the band.

The last received station of the selected band is tuned in.

• Each time you press the button, the band alternates

between “FM” and “AM.”

FM/AM tuner operations are mainly done from the remote

control.

2 Press repeatedly or hold TUNING 9 or

( TUNING until the station you want is

tuned in.

• Pressing (or holding) TUNING 9 increases the

frequency.

• Pressing (or holding) ( TUNING decreases the

frequency.

NOTES

•

When you hold and release TUNING 9 or ( TUNING, the

frequency keeps changing until a station is tuned in.

When a station of sufficient signal strength is tuned in, the TUNED

indicator lights up on the display.

When an FM stereo program is received, the STEREO indicator also

lights up.

Using preset tuning

Once a channel number is assigned to a station, the station

can be quickly tuned in by selecting the number. You can

preset up to 30 FM and 15 AM stations.

7To store the preset stations

Before you start, remember...

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 2again.

From the remote control ONLY:

1 Tune in to the station you want to preset

(see “Tuning in to stations manually”

above).

• If you want to store the FM reception mode for this

station, select the FM reception mode you want. See

“Selecting the FM reception mode” on page 25.

NOTE

2 Press MEMORY.

When you have selected “FM” or “AM” by using SOURCE SELECTOR

on the front panel, the remote control may not work for tuner

operations. To use the remote control for tuner operations, select

“FM” or “AM” by using the FM/AM button on the remote control.

The channel number position starts flashing on the display

for about 5 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

On the front panel:

3 Press the numeric buttons (0 – 9, h10)

to select a channel number while the

channel number position is flashing.

2 1, 3

• For channel number 5, press 5.

• For channel number 10, press h10, 1, then 0.

• For channel number 25, press h10, 2, then 5.

Before you start, remember...

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 2again.

1 Turn SOURCE SELECTOR to select “FM” or

“AM.”

4 Press MEMORY again while the selected

channel number is flashing on the

display.

The last received station of the selected band is tuned in.

2 Press TUNER PRESET.

The selected channel number stops flashing.

The channel number is assigned to the station.

“P” appears on the display, and MULTI JOG now works for

selecting preset channels.

5 Repeat steps 1 to 4 until you store all the

3 Turn MULTI JOG to select a preset

stations you want.

channel number.

To erase a stored preset station:

• To increase the preset channel numbers, turn MULTI JOG

Storing a new station on a used channel number erases the

previously stored one.

clockwise.

• To decrease the preset channel numbers, turn MULTI

JOG counterclockwise.

7To tune in a preset station

From the remote control:

Selecting the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, you

can change the FM reception mode.

1 Press FM/AM to select the band.

The last received station of the selected band is tuned in

and the numeric buttons now work for selecting preset

channels.

• You can store the FM reception mode for each preset station

(see page 24).

• Each time you press FM/AM, the band alternate between

“FM” and “AM.”

From the remote control ONLY:

While listening to an FM station, press FM

MODE.

• Each time you press the button, the FM reception mode

alternates between “AUTO MUTING” and “MONO.”

2 Press the numeric buttons (0 – 9, h10) to

AUTO MUTING Normally select this.

When a program is broadcast in stereo, you

will hear stereo sound; when in monaural,

you will hear monaural sound. This mode is

also useful to suppress static noise between

stations. The AUTO MUTING indicator lights

up on the display.

select a preset channel number.

• For channel number 5, press 5.

• For channel number 10, press h10, 1, then 0.

• For channel number 25, press h10, 2, then 5.

MONO

Select this to improve the reception (but

stereo effect will be lost).

In this mode, you will hear noise while

tuning in to the stations. The AUTO MUTING

indicator goes off from the display. (The

STEREO indicator also goes off.)

Initial setting: AUTO MUTING

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

XM Satellite Radio

operations

To listening to XM Satellite Radio, you need the following:

– The XM Passport System*¹(not supplied)—XM Passport and

XM Passport Home Dock

– Subscription to XM Satellite Radio*²

*¹To connect the XM Passport System with this receiver, see

page 7.

*²The following channels are available without subscription:

– Channel 0: This channel is for checking the XM Satellite

Radio ID code.

– Channel 1: This is “XM Preview” channel.

This is an XM Ready® receiver.

• Before operating, refer also to the manual of your XM

Passport System (not supplied).

How to subscribe

XM Satellite radio is a subscription service.

To subscribe to the XM Satellite Radio, visit the XM Satellite

Radio’s web site at <http://xmradio.com/activation/>, or you

can call 1-800-XM-RADIO (1-800-967-2346).

For subscription, you need to have the XM Satellite radio ID

code. To check the ID code, follow the procedure below:

How to check the XM Satellite Radio ID code

After connection:

1 Press XM on the remote control or turn

SOURCE SELECTOR on the front panel to

select “XM” as the source.

2 Tune in to “Channel 0” (see “To tune in to

channels” on page 27) to check your XM

Satellite Radio ID code.

The display alternately shows “RADIO ID” and the 8-digit

(alphanumeric) ID code.

To cancel the ID code display

Select any channel other than “Channel 0.”

Listening to the XM Satellite Radio

NOTE

When you have selected “XM” by using SOURCE SELECTOR on the

front panel, the remote control may not work for XM Satellite Radio

operations. To use the remote control for the XM Satellite Radio

operations, select “XM” by using the XM button on the remote

control.

1 Press XM on the remote control or turn

SOURCE SELECTOR on the front panel to

select “XM” as the source.

The last received channel is tuned in.

“XM” appears and then the channel name appears on the

display.

7About XM Satellite Radio

XM Satellite Radio is a satellite radio service with digital-

quality sound and over 170 digital channels, the most

commercial-free music in satellite radio services, live concerts

plus exclusive original programming, the biggest names in

news, talk, and entertainment, the most sports play-by-play

including Major League Baseball®. For the latest channel

listings and programming information, or to sign up, visit

<http://www.xmradio.com>.

Channel number

Channel name

XM Ready® is a registered trademark of XM Satellite Radio

2 Tune in to the desired channel.

You can tune in to channels with one of the following

methods:

Major League Baseball® is a registered trademark of Major

League Baseball Properties, Inc.

– Channel Search

– Category Search

– Direct Channel Access

For SIRIUS Satellite Radio operations, see page 47.

For details, see “To tune in to channels” on page 27.

Download from Www.Somanuals.com. All Manuals Search And Download.

Direct Channel Access

You can tune in to the desired channel directly by entering the

channel number.

7To tune in to channels

From the remote control ONLY:

Channel Search

Before you start, remember...

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 2again.

You can search and tune in to all channels.

1 Press XM to select “XM” as the source.

2 Press the DIRECT button.

2 Press repeatedly or hold CHANNEL

+/– until the desired channel number

appears on the display.

The receiver enters the Direct Access mode and the

numeric buttons now work for entering channel numbers.

The channel number position starts flashing on the display

for about 5 seconds.

• Pressing (or holding) CHANNEL + increases the channel

number.

• Pressing (or holding) CHANNEL – decreases the channel

number.

NOTE

While searching, the invalid and unsubscribed channels are skipped.

3 Press the numeric buttons (0 – 9, h10) to

enter the desired channel number while

the channel number position is flashing.

Category Search

You can select the channel category and tune in to only the

channels included in the selected category.

• For channel number 005, press 5.

• For channel number 010, press h10, 1, then 0.

• For channel number 025, press h10, 2, then 5.

• For channel number 115, press h10, h10, 1, 1, then 5.

Before you start, remember...

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 2again.

1 Press XM to select “XM” as the source.

2 Press CAT 9 or ( CAT.

Using preset tuning

The receiver enters the Category Search mode.

The category name of the currently selected channel

appears and “>” starts flashing on the display for about 15

seconds.

Once a preset number is assigned to a channel, the channel

can be quickly tuned in by selecting the number. You can

preset up to 30 channels.

Channel number

Category name

7To store the preset channels

Before you start, remember...

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 2again.

3 Press CAT 9 or ( CAT repeatedly to

display the desired category name on

the display while “>” is flashing.

From the remote control ONLY:

1 Tune in to the channel you want to

preset (see “To tune in to channels” on

the left column).

2 Press MEMORY.

4 Press repeatedly or hold CHANNEL

The preset number position starts flashing on the display

for about 5 seconds.

+/– until the desired channel is tuned in.

• Pressing (or holding) CHANNEL + increases the channel

number included in the selected category.

• Pressing (or holding) CHANNEL – decreases the channel

number included in the selected category.

3 Press the numeric buttons (0 – 9, h10) to

select a preset number while the preset

number position is flashing.

NOTE

While searching, the invalid and unsubscribed channels are skipped.

• For preset number 5, press 5.

• For preset number 10, press h10, 1, then 0.

• For preset number 25, press h10, 2, then 5.

Continued on the next page

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Press MEMORY again while the selected

Changing the channel information

preset number is flashing on the display.

While listening to the XM Satellite Radio, the currently

selected channel information appears on the display.

You can change the type of channel information.

5 Repeat steps 1 to 4 until you store all the

desired channels.

To erase a stored preset channel

Storing a new channel on a used preset number erases the

previously stored one.

From the remote control ONLY:

Press DISPLAY.

Each time you press the button, the channel information

changes as follows:

7To tune in a preset channel

CHAN (channel name)* = NAME (artist name/feature) =

TITLE (song/program title) = CAT (category name) = (Back

to the beginning)

From the remote control:

1 Press XM.

* CHAN (channel name) is the initial setting.

The last received channel is tuned in.

EX.: When the category name is selected:

2 Press the numeric buttons (0 – 9, h10) to

select a preset channel number.

• For preset number 5, press 5.

• For preset number 10, press h10, 1, then 0.

• For preset number 25, press h10, 2, then 5.

After 1 second

On the front panel:

Before you start, remember...

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 2again.

NOTES

•

If you turn off the power or select another source, the display is

changed back to the initial setting.

When you tune in to another channel, the channel name appears

on the display and then the channel information you have selected

appears.

1 Turn SOURCE SELECTOR to select “XM.”

The last received channel is tuned in.

2 Press TUNER PRESET.

•

When all the text information cannot be shown on the display at a

time, the text scrolls.

Some characters cannot be displayed correctly.

“P” flashes on the display, and MULTI JOG now works for

selecting preset channels.

3 Turn MULTI JOG to select a preset

number.

• To increase the preset numbers, turn MULTI JOG

clockwise.

• To decrease the preset numbers, turn MULTI JOG

counterclockwise.

7Messages on the display

When problems occur, a message appears on the display. In this case, refer to the following solution.

Message

Possible cause

Solution

NO SIGNAL

Signals are too weak.

Move the XM Passport Home Dock antenna

near a south-facing window or where

“Channel 1” can be heard clearly.

CHECK ANTENNA

The XM Passport Home Dock antenna is

not connected properly.

Check the connection (see page 7).

This receiver is loading the channel

information and audio data.

It takes a few minutes to complete. Wait until

loading is finished.

OFF AIR

Selected channel is not currently

broadcasting any signal.

Select another channel.

UPDATING

The latest encryption code is being

updated.

Wait until updating is finished.

• Channel number and “-----”

• Preset number, channel

number, and “-----”

No text information for the selected

channel is available.

—

• Channel number and “CH---”

• Preset number and “---<CH---”

Selected channel does not exist or is not

subscribed yet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Items

To do

EX/ES/PLIIx

Select the EX/ES/PLIIx reproduction

mode. (32)

Basic settings

DUAL MONO

Select the Dual Mono sound channel.

(32)

SUBWOOFER OUT Select sounds emitted from the

subwoofer. (33)

CROSSOVER*

LFE ATT

Select the cutoff frequency to the

subwoofer. (33)

Attenuate the bass (LFE) sounds. (33)

To obtain the best possible sound effect from the Surround/

DSP modes (see pages 39 to 44), you need to set up the

speaker and subwoofer information after all the connections

are completed. From pages 29 to 34, how to set speakers and

other basic items of the receiver are explained.

MIDNIGHT MODE Reproduce a powerful sound at night.

(33)

DIGITAL IN 1

Select the component connected to the

digital coaxial terminal—1(DVR/DVD).

(34)

DIGITAL IN 2

DIGITAL IN 3

AUDIO DELAY

Select the component connected to the

digital optical terminal—2(DBS). (34)

Basic setting items

Select the component connected to the

digital optical terminal—3(VCR). (34)

You can adjust the following items. See pages in parentheses

for details.

Set the audio delay time to correct

synchronization between video and

audio signals. (34)

• You cannot select the items which is not available with the

current setting. For example, when “S BACK SPK” is set to

“NO,” you cannot select the following items:

S BACK OUT, S BACK DIST, S BACK L DIST, S BACK R DIST

HDMI SELECT

CMPNT SELECT

VIDEO OUTPUT

Select the source for HDMI VCR (DBS) IN

terminal. (34)

Items

To do

Select the source for COMPONENT VCR

(DBS) IN jacks. (34)

SUBWOOFER*

FRONT SPK*

CENTER SPK*

SURROUND SPK*

S BACK SPK*

Select the output video signal. (34)

* If you have performed Precise Surround Setup on pages 16

to 18, these settings are not required.

size. (30)

NOTE

Some items above are not available in the following cases below:

– When selecting “A MULTI” for the audio input setting (see page 11)

– When multi-channel PCM signals (see page 41) are coming in with

selecting “HDMI” for the audio input setting (see page 11)

S BACK OUT*

DIST UNIT

back speaker(s). (31)

Select the measuring unit for the

speaker distance. (31)

FRONT L DIST*

FRONT R DIST*

speaker to your listening point. (31)

front speaker to your listening point.

(31)

CENTER DIST*

SURR L DIST*

speaker to your listening point. (31)

surround speaker to your listening

point. (31)

SURR R DIST*

S BACK DIST*

surround speaker to your listening

point. (31)

back speaker to your listening point

when using a single speaker for the

surround back speaker. (31)

S BACK L DIST*

S BACK R DIST*

surround back speaker to your listening

point. (31)

surround back speaker to your listening

point. (31)

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating procedure

Setting the speakers

To obtain the best possible surround effect from the Surround

and DSP modes, register the setting about the speaker after all

connections are completed.

1, 7

3, 5

2, 4

• If you have performed Precise Surround Setup on pages 16

to 18, the following settings are not required.

7Setting subwoofer information—

On the front panel ONLY:

Before you start, remember...

SUBWOOFER

Select if you have connected a subwoofer or not.

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 1again.

SUBWFR YES

Select when you have connected a

subwoofer.

Ex.: When setting the DIGITAL IN 1 terminal

The subwoofer indicator (

) lights up on

the display. You can adjust the subwoofer

output level (see page 36).

1 Press SETTING.

MULTI JOG now works for the setting operation.

SUBWFR NO

Select when you have not connected a

subwoofer. Selecting this changes the front

speaker size to “LRG” (see below).

2 Turn MULTI JOG until the item you want

to set appears on the display.

Initial setting: NO

• As you turn MULTI JOG, the setting items change as

follows:

7Setting the speaker size—FRONT SPK (front

speakers), CENTER SPK (center speaker),

SURROUND SPK (surround speakers), S BACK

SPK (surround back speakers)

SUBWOOFER Ô FRONT SPK Ô CENTER SPK Ô

SURROUND SPK Ô S BACK SPK Ô S BACK OUT Ô

DIST UNIT Ô FRONT L DIST Ô FRONT R DIST Ô

CENTER DIST Ô SURR L DIST Ô SURR R DIST Ô

S BACK DIST Ô S BACK L DIST Ô S BACK R DIST Ô

EX/ES/PLIIx Ô DUAL MONO Ô SUBWOOFER OUT

Ô CROSSOVER Ô LFE ATT Ô MIDNIGHT MODE Ô

DIGITAL IN 1 Ô DIGITAL IN 2 Ô DIGITAL IN 3 Ô

AUDIO DELAY Ô HDMI SELECT Ô CMPNT SELECT

Ô VIDEO OUTPUT Ô (Back to the beginning)

LRG (large)

SML (small)

Select when the cone speaker size is larger

than 12 cm.

Select when the cone speaker size is smaller

than 12 cm.

Select when you have not connected

the speaker. (Not selectable for the front

speakers.)

3 Press SET.

Initial setting: LRG (for the front speakers)

The current setting of the selected item appears.

SML (for the other speakers)

NOTES

•

If you have selected “SML (small)” for the front speaker size, you

cannot select “LRG (large)” for other speakers.

When “SUBWOOFER” is set to “NO,” the front speaker size is fixed to

“LRG (large)” (and you cannot select “SML (small)”).

When “SURROUND SPK” is set to “SML (small),” you cannot select

“LRG (large)” for the surround back speaker.

4 Turn MULTI JOG to select the appropriate

setting.

When “SURROUND SPK” is set to “NO,” the surround back speaker is

fixed to “NO.”

DVR/DVD Ô DBS Ô VCR Ô TV

5 Press SET.

Your setting is stored.

6 Repeat steps 2 to 5 to set other items if

necessary.

7 Press SETTING.

The source indication resumes on the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

7Setting the surround back speaker(s)—

S BACK OUT

3.3 m

(11 ft)

SB OUT 1SPK

SB OUT 2SPK

Select when you use a single surround back

speaker.

2.7 m

(9 ft)

Select when you use 2 surround back

speakers.

3.0 m

(10 ft)

2.1 m

(7 ft)

2.4 m

(8 ft)

Initial setting: 2SPK

NOTES

•

When “S BACK SPK” is set to “NO,” you cannot select “S BACK OUT.”

When “S BACK OUT” is set to “1SPK,” connect the surround back

speaker to the left surround back speaker terminal (see page 8). No

sound comes from the surround back speaker if you connect it to

the right surround back speaker terminal.

SBL

SBR

In this case, set the distance as follows:

Left front speaker (FL):

Right front speaker (FR):

Center speaker (C):

Left surround speaker (SL):

Right surround speaker (SR):

3.0 m (10 ft)

2.7 m (9 ft)

7Setting the speaker distance

The distance from your listening position to the speakers is

one of the important elements to obtain the best possible

sound effect from the Surround/DSP modes.

By referring to the speaker distance, the receiver automatically

sets the delay time of the sound through each speaker so that

sounds through all the speakers can reach you at the same

time.

Left surround back speaker (SBL): 2.4 m (8 ft)

Right surround back speaker (SBR): 2.4 m (8 ft)

• Measuring unit—DIST UNIT

Select which measuring unit you use.

NOTES

•

You cannot set the speaker distance for the speakers you have set

to “NO.”

If you have selected “1SPK” for “S BACK OUT” (see the left column),

“S BACK DIST” appears instead of “S BACK L DIST” and “S BACK R

DIST.”

D UNIT meter Select to set the distance in meters.

D UNIT feet

Select to set the distance in feet.

Initial setting: meter

• Speaker distance—

FRONT L DIST (for the left front speaker), FRONT R DIST

(for the right front speaker), CENTER DIST (for the

center speaker), SURR L DIST (for the left surround

speaker), SURR R DIST (for the right surround speaker),

S BACK L DIST (for the left surround back speaker),

S BACK R DIST (for the right surround back speaker)

Adjustable range: 0.3 m to 9.0 m in 0.15 m intervals

(1 ft to 30 ft in 0.5 ft intervals)

Initial setting:

3.0 m (10 ft) for all speakers

Download from Www.Somanuals.com. All Manuals Search And Download.

Activating the EX/ES/PLIIx setting— Selecting the main or sub channel—

EX/ES/PLIIx

DUAL MONO

Depending on this setting, available Surround modes for

digital multi-channel software vary—EX/ES/PLIIx (7.1-

channel) reproduction or 5.1-channel reproduction. Select an

appropriate setting for your enjoyment.

You can select the playback sound (channel) you want while

playing digital software recorded (or broadcasted) in Dual

Mono mode (see page 41), which includes two monaural

channels separately. When the receiver detects Dual Mono

signals, the DUAL MONO indicator lights up on the display.

• For details about relation between EX/ES/PLIIx setting and

available Surround mode, see page 42.

• To activate the Surround mode, see page 43.

D MONO MAIN

D MONO SUB

D MONO ALL

Initial setting:

Select to play back the main channel (Ch

1).*

Signal indicator “L” lights up while playing

back this channel.

AUTO

According to the incoming signal, an

appropriate Surround mode is applied.

• For Dolby Digital Surround EX and DTS-ES

software, 7.1-channel reproduction is

applied*.

Select to play back the sub-channel (Ch

2).*

Signal indicator “R” lights up while playing

back this channel.

• For other multi-channel (4 channels or

more) encoded software, 5.1-channel

reproduction is applied.

Select to play back both the main and sub-

channels (Ch 1/Ch 2).*

Signal indicators “L” and “R” light up while

playing back these channels.

Select to apply 7.1-channel reproduction to

both 5.1-channel and 6.1-channel encoded

software.

MAIN

PLIIx MOVIE

PLIIx MUSIC

OFF

Select to apply PLIIx MOVIE (7.1-channel)

reproduction to both 5.1-channel and 6.1-

channel encoded software.

* Dual Mono signals can be heard from the following

speakers—L (left front speaker), R (right front speaker), and

C (center speaker), with respect to the current Surround

setting:

Select to apply PLIIx MUSIC (7.1-channel)

reproduction to both 5.1-channel and 6.1-

channel encoded software.

With Surround Activated

Without

Surround

Dual

Mono

setting

Center speaker setting

SML/LRG NO

Select to cancel the EX/ES/PLIIx (7.1-

channel) reproduction.

Initial setting: AUTO

MAIN Ch 1 Ch 1 —

SUB Ch 2 Ch 2 —

Ch 1

Ch 2

—

Ch 1

Ch 2

Ch 1

Ch 2

* For some Dolby Digital Surround EX software, Dolby Digital

5.1-channel reproduction (“DOLBY DIGITAL”) may be

applied even though you have selected “AUTO.” In this case,

select “ON” to apply “DOLBY D EX.” (See page 42.)

ALL Ch 1 Ch 2 — Ch 1+Ch 2 — Ch 1+Ch 2 Ch 1+Ch 2

NOTE

NOTES

The Dual Mono format is not identical with bilingual broadcasting for

TV programs. So this setting does not take effect while watching such

bilingual programs.

•

This function is not available when “SURROUND SPK” is set to “NO”

(see page 30).

When “S BACK SPK” is set to “NO” (see page 30), the Virtual

Surround Back (see page 43) is applied for EX/ES/PLIIx (7.1-channel)

reproduction.

Download from Www.Somanuals.com. All Manuals Search And Download.

7Setting the low frequency effect attenuator

Setting bass sound

—LFE ATT

If the bass sound is distorted while playing back software

encoded with Dolby Digital or DTS, set the LFE level to

eliminate distortion.

7Setting subwoofer output—SUBWOOFER OUT

The subwoofer emits the LFE signals* and the bass elements

of each speaker set “SML (small).”

• This function takes effect only when the LFE signals come in.

You can also make the bass elements of the front speakers

(MAIN) emitted through the subwoofer.

LFE 0dB

Normally select this.

LFE –10dB

Initial setting:

Select when the bass sound is distorted.

0 dB

SW LFE

The subwoofer emits the LFE signals and

the bass elements of the speakers set to

“SML (small).”

SW LFE+MAIN

The subwoofer emits the LFE signals and

the bass elements of the speakers set to

“SML (small).” The subwoofer also emits

the bass elements of front speakers (MAIN)

when no LFE signal nor the bass elements

of “SML (small)” speakers exist.

Using the Midnight mode—

MIDNIGHT MODE

You can enjoy a powerful sound at night using the Midnight

mode.

Initial setting:

LFE

When the Midnight mode is activated, the MIDNIGHT

indicator lights up on the display.

* The LFE signals are emitted only when playing the following

software with the LFE signals:

– Dolby Digital multi-channel software

– DTS multi-channel software

When playing analog source or linear PCM software, no LFE

signal is emitted.

MIDNIGHT OFF

Select when you want to enjoy surround

with its full dynamic range. (No effect

applied.)

MIDNIGHT 1

MIDNIGHT 2

Initial setting:

Select when you want to reduce the

dynamic range a little.

NOTE

Select when you want to apply the

compression effect fully (useful at night).

When “SUBWOOFER” is set to “NO” (see page 30), you cannot select

“SUBWOOFER OUT.”

OFF

7Setting the crossover frequency—CROSSOVER

Small speakers cannot reproduce the bass sounds efficiently.

If you use a small speaker in any position, this receiver

automatically reallocates the bass sound elements assigned to

the small speaker to the large speakers.

To use this function properly, set this crossover frequency

level according to the size of the small speaker connected.

• If you have selected “LRG (large)” for all speakers (see page

30), this function will not take effect (“CROSS OFF” appears).

• If you have performed Precise Surround Setup on pages 16

to 18, this setting is not required.

Adjustable range: 80 Hz to 200 Hz (in 10 Hz intervals)

Initial setting:

100 Hz

The following are examples of the setting:

CROSS 80Hz

CROSS 100Hz

CROSS 120Hz

CROSS 150Hz

CROSS 200Hz

Select when the cone speaker unit built in

the speaker is about 12 cm.

Select when the cone speaker unit built in

the speaker is about 10 cm.

Select when the cone speaker unit built in

the speaker is about 8 cm.

Select when the cone speaker unit built in

the speaker is about 6 cm.

Select when the cone speaker unit built in

the speaker is less than 5 cm.

NOTE

Crossover frequency is not valid for the HEADPHONE and 3D

HEADPHONE modes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the digital input (DIGITAL IN) Selecting the source for HDMI

terminals—DIGITAL IN 1/2/3

terminal and COMPONENT VIDEO

When you use the digital input terminals, register what

components are connected to which terminals—DIGITAL

IN 1/2/3 (see page 14) so that the correct source name will

appear when you select the digital source.

jacks—HDMI SELECT/CMPNT SELECT

When you connect a VCR or DBS to the HDMI VCR(DBS) IN

terminal or COMPONENT VIDEO jacks on the rear of the

receiver, you need to select either “VCR” or “DBS” for each

terminal according to the component you connect.

If you have not selected an appropriate source, you cannot

view the playback picture on the TV.

Select one of the following components for each terminal:

DVR/DVD

DBS

For the DVD player (or DVD recorder)

For the DBS tuner

For the VCR

VCR

For the HDMI terminal:

For the TV

HDMI VCR

Select this when connecting a VCR to the

HDMI terminal.

Initial setting:

DVR/DVD (for “DIGITAL IN 1”)

DBS (for “DIGITAL IN 2”)

VCR (for “DIGITAL IN 3”)

HDMI DBS

Select this when connecting a DBS tuner to

the HDMI terminal.

Initial setting:

VCR

NOTES

•

You cannot assign the same component for different terminals.

The priority order for assignment is as follows:

“DIGITAL IN 1” > “DIGITAL IN 2” > “DIGITAL IN 3”

For the COMPONENT VIDEO jacks:

CMPNT VCR

CMPNT DBS

Initial setting:

Select this when connecting a VCR to the

COMPONENT VIDEO jacks.

Ex.: When “DIGITAL IN 1” is set to “DVR/DVD.”

Select this when connecting a DBS tuner to

the COMPONENT VIDEO jacks.

DIGITAL IN 1 DVR/DVD

DBS

VCR

‘

VCR

For “DIGITAL IN 2,” “DBS,” “VCR,” and “TV” are selectable.

In this case, “VCR” is selected.

•

DIGITAL IN 2 DVR/DVD

DBS

VCR

‘

Selecting the output video signals—

VIDEO OUTPUT

For “DIGITAL IN 3,” “DBS” and “TV” are selectable.

DIGITAL IN 3 DVR/DVD

DBS

VCR

When you connect your TV and this receiver with the HDMI

cable, set this setting to “HDMI.”

: Selectable

: Not selectable

With this setting, this receiver converts incoming composite

video, S-video, and component video signals from video

components and transmits the converted signals through the

HDMI cable.

•

Setting “DIGITAL IN 1” affects “DIGITAL IN 2” and “DIGITAL IN 3”

settings. When you have changed “DIGITAL IN 1,” confirm the

components assigned to “DIGITAL IN 2” and “DIGITAL IN 3.”

VIDEO HDMI

VIDEO OTHER

Initial setting:

Select this when connecting a TV to the

HDMI terminal.

Select this when connecting a TV to any

video jack other than the HDMI terminal.

Setting the Audio delay level—

AUDIO DELAY

HDMI

Synchronization between audio and video reproduction can

be possibly disturbed because video signal decoding is time-

consuming compared to the audio signal decoding.

NOTE

When selecting “HDMI,” the AV COMPU LINK remote control system is

restricted (see page 45).

On this setting, you can correct synchronization between

video and audio signals by delaying the audio signal timing.

Adjustable range: OFF and 10 ms to 150 ms (in 10 ms

intervals)

Initial setting:

OFF

NOTE

The audio delay level setting does not take effect when selecting “A

MULTI” for the audio input setting (see page 11).

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE

Some items are not available in the following cases below:

– When selecting “A MULTI” for the audio input setting (see page 11)

– When multi-channel PCM signals (see page 41) are coming in with

selecting “HDMI” for the audio input setting (see page 11)

Sound adjustments

Operating procedure

On the front panel:

1, 7

3, 5

2, 4

You can make sound adjustment to your preference after

completing basic setting.

Basic adjustment items

You can adjust the following items. See pages in parentheses

Before you start, remember...

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 1again.

for details.

• You cannot select the items which is not available with the

current setting.

Ex.: When adjusting subwoofer output level.

Items

To do

SUBWFR LVL*^{1, 2}Adjust the subwoofer output level. (36)

1 Press ADJUST.

FRONT L LVL*^{1, 2}Adjust the left front speaker output level.

MULTI JOG now works for the sound adjustment.

(36)

FRONT R LVL*^{1, 2}Adjust the right front speaker output level.

2 Turn MULTI JOG until the item you want

(36)

to adjust appears on the display.

CENTER LVL*^{1, 2}Adjust the center speaker output level. (36)

• As you turn MULTI JOG, the adjustment items change as

follows:

SURR L LVL*^{1, 2}

SURR R LVL*^{1, 2}

S BACK LVL*^{1, 2}

Adjust the left surround speaker output

level. (36)

Adjust the right surround speaker output

level. (36)

Adjust the surround back speaker output

level when using a single speaker for the

surround back speaker. (36)

SUBWFR LVL Ô FRONT L LVL Ô FRONT R LVL Ô

CENTER LVL Ô SURR L LVL Ô SURR R LVL Ô

S BACK LVL Ô S BACK L LVL Ô S BACK R LVL Ô

D EQ 63Hz Ô D EQ 250Hz Ô D EQ 1kHz Ô

D EQ 4kHz Ô D EQ 16kHz Ô BASS BOOST Ô

INPUT ATT Ô EFFECT Ô ROOM SIZE Ô

LIVENESS Ô PANORAMA Ô CENTER WIDTH Ô

DIMENSION Ô CENTER GAIN Ô CENTER TONE Ô

CENTER ALIGN Ô (Back to the beginning)

S BACK L LVL*^{1, 2}Adjust the left surround back speaker

output level. (36)

S BACK R LVL*^{1, 2}Adjust the right surround back speaker

output level. (36)

Adjust the equalization pattern of each

band. (36)

D EQ 63Hz*¹

D EQ 250Hz*¹

D EQ 1kHz*¹

D EQ 4kHz*¹

D EQ 16kHz*¹

3 Press SET.

BASS BOOST

INPUT ATT

Boost the bass level. (37)

Attenuate the input level of analog source.

(37)

The current setting for the selected item appears.

EFFECT

Adjust the effect level. (37)

ROOM SIZE

Select the room size for your virtual

listening room. (37)

LIVENESS

Select the liveness level for your virtual

listening room. (37)

Add “wraparound” sound effect with

sidewall image. (37)

4 Turn MULTI JOG to adjust the selected

item.

PANORAMA

CENTER WIDTH Adjust the center channel localization

between the center speaker and the left/

right speakers. (38)

–10

+10

DIMENSION

Adjust sound localization pattern. (38)

5 Press SET.

CENTER GAIN

Adjust the sound localization of the center

channel. (38)

Your adjustment is stored.

CENTER TONE

CENTER ALIGN

Make the center tone soft or sharp. (38)

Align the vertical localization of the center

channel signals. (38)

6 Repeat steps 2 to 5 to adjust other items

if necessary.

*¹You can adjust these items directly from the remote control.

*²If you have performed Precise Surround Setup on pages 16

to 18, these settings are not required.

7 Press ADJUST.

The source indication resumes on the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the speaker output levels Adjusting the equalization

• SUBWFR LVL (subwoofer output level)

• FRONT L LVL (left front speaker output level)

• FRONT R LVL (right front speaker output level)

• CENTER LVL (center speaker output level)

• SURR L LVL (left surround speaker output level)

• SURR R LVL (right surround speaker output level)

• S BACK LVL (surround back speaker output level)

• S BACK L LVL (left surround back speaker output level)

patterns—D EQ 63Hz/250Hz/1kHz/

4kHz/16kHz

You can adjust equalization patterns in five frequency bands

(center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the

front speakers.

• Once you have made an adjustment, it is memorized for

each source.

• S BACK R LVL (right surround back speaker output level)

Adjustable range: –8 (dB) to +8 (dB) (in 2 dB intervals)

You can adjust the speaker output levels.

Initial setting:

0 (dB) for all bands

By using Precise Surround Setup (see pages 16 to 18), you can

set the output levels of all the speakers to the same levels.

• When making an adjustment, the DIGITAL EQ indicator

lights up on the display.

Adjustable range: –10 (dB) to +10 (dB) (in 1 dB intervals)

Initial setting:

0 (dB) for all speakers

If no adjustment is required, set all the frequency bands to

“0 (dB).”

• The DIGITAL EQ indicator goes off from the display.

NOTES

•

If you have selected “NO” for a speaker (see page 30), the output

From the remote control:

Before you start, remember...

There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1again.

level for the corresponding speaker is not adjustable.

If you have selected “1SPK” for “S BACK OUT” (see page 31), “S BACK

LVL” appears instead of “S BACK L LVL” and “S BACK R LVL.”

While using the headphones, you cannot adjust the speaker output

levels.

1 Press D. EQ FREQ repeatedly to

select the band you want

to adjust.

From the remote control:

1 Press TEST to check the speaker output

balance.

2 Press D. EQ LEVEL + or – to

“TEST FL” starts flashing on the display, and test tones

come out of the speakers clockwise.

adjust the equalization

pattern of the selected

band.

3 Repeat steps 1 and 2 to

1, 3

FL = C = FR = SR = SBR*

= SBL* = SL = SW =

(Back to the beginning)

adjust other bands.

• You can adjust the speaker output levels without the

test tone.

2 Adjust the speaker output levels.

Press the + or – button corresponding to the speaker

you want to adjust.

3 Press TEST again to stop the test tone.

* When using a single speaker for the surround back

speaker, the test tone comes out of “SB” instead of “SBR”

and “SBL.”

NOTES

•

No test tone comes out of the speakers for which the speaker

setting is set to “NO” (see page 30).

•

No test tone is available when the headphones are in use.

If you have selected “1SPK” for “S BACK OUT” (see page 31), press

S. BACK L +/– to adjust the output level.

•

When the PSS indicator is lit, the frequency response of each

channel appears on the display with the test tone. (See page 18.)

Download from Www.Somanuals.com. All Manuals Search And Download.

7Adjusting the virtual room size for DSP

Reinforcing the bass—BASS BOOST

modes—ROOM SIZE

You can boost the bass level—Bass Boost.

• Once you have made an adjustment, it is memorized for

each source.

This setting is available only when one of the DSP modes

(except All Channel Stereo) is in use. To activate DSP mode,

see pages 43 and 44.

• If “SURROUND SPK” is set to “NO” (see page 30), this item is

not adjustable.

• You cannot adjust directly from the remote control.

B BOOST ON

Select to boost the bass level.

The B.BOOST indicator lights up on the

display.

• Once you have made an adjustment, it is memorized for

each DSP mode.

B BOOST OFF

Initial setting:

Select to deactivate the Bass Boost.

OFF

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting:

As the number increases, the interval between reflections

increases so that you will feel as if you were in a larger room.

Normally, select “3.”

NOTE

This function affects only the sound coming out through the front

speakers.

7Adjusting the liveness effect for DSP

Attenuating the input signal—

INPUT ATT

modes—LIVENESS

This setting is available only when one of the DSP modes

(except All Channel Stereo) is in use. To activate DSP mode,

see pages 43 and 44.

• If “SURROUND SPK” is set to “NO” (see page 30), this item is

not adjustable.

When the input level of analog source is too high, the sound

will be distorted. If this happens, you need to attenuate the

input signal level to prevent the sound distortion.

• Once you have made an adjustment, it is memorized for

each source.

• Once you have made an adjustment, it is memorized for

each DSP mode.

• You cannot adjust directly from the remote control.

ATT ON

Select to attenuate the input signal level.

The INPUT ATT indicator lights up on the

display.

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting:

As the number increases, the attenuation level of reflections

over time decreases so that acoustics change from “Dead” to

“Live.”

ATT NORMAL

Initial setting:

Select to deactivate attenuation.

NORMAL

Normally, select “3.”

Adjusting the sound parameters for

the Surround/DSP modes

7Adjusting the panorama control for Pro Logic

IIx Music and Pro Logic II Music—PANORAMA

This setting is available when Pro Logic IIx Music or Pro Logic

II Music is activated for the analog or digital 2-channel sound

signal.

To activate Pro Logic IIx Music or Pro Logic II Music, see pages

43 and 44.

You can adjust the Surround/DSP sound parameters to your

preference.

• For details about the Surround/DSP modes, see pages 39 to

44.

• You cannot adjust these items directly from the remote

control.

• Once you have made an adjustment, it is memorized until

you change the setting.

PANORAMA ON

PANORAMA OFF

Initial setting:

Select to add “wraparound” sound effect

with side-wall image.

7Adjusting the effect level for DSP modes—

Select to listen to originally recorded

sound.

EFFECT

This setting is available only when one of the DSP modes

(except All Channel Stereo) is in use. To activate DSP mode,

see pages 43 and 44.

OFF

• Once you have made an adjustment, it is memorized for

each DSP mode.

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting:

As the number increases, the effect becomes stronger.

Normally, select “3.”

Download from Www.Somanuals.com. All Manuals Search And Download.

7Adjusting the center channel localization for

Pro Logic IIx Music and Pro Logic II Music—

CENTER WIDTH

7Adjusting the center tone—CENTER TONE

This setting is available when one of the Surround/DSP modes

is in use. To activate Surround/DSP mode, see pages 43 and

44.

This setting is available when Pro Logic IIx Music or Pro Logic

II Music is activated for the analog or digital 2-channel sound

signal.

• If “CENTER SPK” is set to “NO” (see page 30), this item is not

adjustable.

• This setting is common to all Surround modes, and is

memorized separately for DSP modes.

To activate Pro Logic IIx Music or Pro Logic II Music, see pages

43 and 44.

• If “CENTER SPK” is set to “NO” (see page 30), this item is not

adjustable.

• Once you have made an adjustment, it is memorized until

you change the setting.

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting:

As the number increases, the dialogue becomes stronger.

Normally, select “3.”

Adjustable range: OFF and 1 to 7 (in 1 step intervals)

• When the center tone is set to other than “3,” the C.TONE

indicator lights up on the display.

Initial setting:

As the number increases, the center channel sound moves

toward the left and right speakers.

Normally, select “3.”

7Aligning the vertical localization of the

center channel for Surround/DSP modes—

CENTER ALIGN

This setting is available when one of the Surround/DSP modes

(except Pro Logic IIx Music, Pro Logic II Music, Neo:6 Music,

and All Channel Stereo) is in use. To activate Surround/DSP

mode, see pages 43 and 44.

• If “CENTER SPK” is set to “NO” (see page 30), this item is not

adjustable.

• Once you have made an adjustment, it is memorized for

each Surround/DSP mode.

7Adjusting the sound localization position

for Pro Logic IIx Music and Pro Logic II Music

—DIMENSION

This setting is available when Pro Logic IIx Music or Pro Logic

II Music is activated for the analog or digital 2-channel sound

signal.

To activate Pro Logic IIx Music or Pro Logic II Music, see pages

43 and 44.

• Once you have made an adjustment, it is memorized until

you change the setting.

C ALIGN ON

Select this when you cannot feel as if the

actors or singers are speaking or singing on

the screen.

C ALIGN OFF

Center alignment is turned off.

OFF

Adjustable range: 1 to 7 (in 1 step intervals)

Initial setting:

As the number increases, the sound localization moves

towards forward from backward.

Normally, select “4.”

7Adjusting the sound localization of the center

channel—CENTER GAIN

This setting is available only when Neo:6 Music is in use.

• If “CENTER SPK” is set to “NO” (see page 30), this item is not

adjustable.

• Once you have made an adjustment, it is memorized until

you change the setting.

Adjustable range: 0 to 1.0 (in 0.1 step intervals)

Initial setting:

0.3

As the number increases, the center channel will be localized

clearly.

Normally, select “0.3.”

Download from Www.Somanuals.com. All Manuals Search And Download.

Introducing the Surround modes

Creating realistic

sound fields

7Dolby Digital*

Dolby Digital is a digital signal compression method,

developed by Dolby Laboratories, and enables multi-channel

encoding and decoding.

• When Dolby Digital signal is detected through the digital

input, the

indicator lights up on the display.

Dolby Digital 5.1CH

Dolby Digital 5.1CH (DOLBY DIGITAL) encoding method

records and digitally compresses the left front channel, right

front channel, center channel, left surround channel, right

surround channel, and LFE channel signals (total 6 channels,

but the LFE channel is counted as 0.1 channel; therefore,

called 5.1 channel).

Reproducing theater ambience

In a movie theater, many speakers are located on the walls to

reproduce impressive multi-channel sound, reaching you from

all directions.

Dolby Digital enables stereo surround sounds, and sets the

cutoff frequency of the surround treble at 20 kHz, compared

to 7 kHz for Dolby Pro Logic. As such, the sound movement

and “being-there” feeling are enhanced much more than

Dolby Pro Logic.

With these many speakers, sound localization and sound

movement can be expressed.

Surround/DSP modes built in this receiver can create almost

the same Surround sound as you can feel in a real movie

theater.

Dolby Digital EX

Dolby Digital EX (DOLBY D EX) is a digital surround encoding

format that adds the third surround channels, called “surround

back.”

Compared to the conventional Dolby Digital 5.1CH, these

newly added surround back channels can reproduce more

detailed movements behind you while viewing the video

software. In addition, surround sound localization will become

more stable.

7Dolby Surround

Dolby Pro Logic II

Dolby Pro Logic II is a multi-channel playback decoder to

convert 2-channel software into 5-channel (plus subwoofer).

The matrix-based conversion method used for Dolby Pro Logic

II makes no limitation for the cutoff frequency of the surround

treble and enables stereo surround sound.

• This receiver provides three types of Dolby Pro Logic II

modes—Pro Logic II Movie (PLII MOVIE), Pro Logic II Music

(PLII MUSIC), and Pro Logic II Game (PLII GAME).

When Dolby Pro Logic II is activated, the

lights up on the display.

indicator

PLII MOVIE Suitable for playing any Dolby Surround

encoded software. You can enjoy a sound field

very close to the one created with discrete 5.1-

channel sounds.

PLII MUSIC Suitable for playing any 2-channel stereo

software. You can enjoy wide and deep

sounds.

PLII GAME

Suitable for when playing a video game. You

can enjoy sounds with “being there” feeling.

* Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are

trademarks of Dolby Laboratories.

SBL

(SB)

SBR

Continued on the next page

Download from Www.Somanuals.com. All Manuals Search And Download.

Dolby Pro Logic IIx

DTS 96/24

Dolby Pro Logic IIx is another multi-channel playback

decoder to convert not only multi-channel software but

2-channel software into 7.1 channel (or 6.1 channel) that

developed from Dolby Pro Logic II. The matrix-based

conversion method used for Dolby Pro Logic IIx makes no

limitation for the cutoff frequency of the surround treble.

• This receiver provides three types of Dolby Pro Logic IIx

modes—Pro Logic IIx Movie (PLIIx MOVIE), Pro Logic IIx

Music (PLIIx MUSIC), and Pro Logic IIx Game (PLIIx GAME).

When Dolby Pro Logic IIx is activated, “PLIIx MOVIE,” “PLIIx

In recent years, there has been increasing interest in higher

sampling rates both for recording and for reproducing at

home. Higher sampling rates allow wider frequency range and

greater bit depths provide extended dynamic range.

DTS 96/24 is a multi-channel digital signal format (fs 96

kHz/24 bits) introduced by Digital Theater Systems, Inc. to

deliver “better-than-CD sound quality” into the home.

• When DTS 96/24 signal is detected, the

96/24 indicator

lights up. You can enjoy its 5.1-channel sound with full-

quality.

MUSIC,” or “PLIIx GAME” appear and the

lights up on the display.

indicator

DTS Neo:6

DTS Neo:6 is another conversion method to create 6-channel

(plus subwoofer) from analog/digital 2-channel software by

using the high precision digital matrix decoder used for DTS-

ES Matrix 6.1ch.

PLIIx MOVIE Suitable for playing any Dolby Surround

encoded software. You can enjoy a sound field

with a natural wraparound effect.

• This receiver provides the following DTS Neo:6 modes—

Neo:6 Cinema (NEO:6 CINEMA) and Neo:6 Music (NEO:6

MUSIC).

When one of them is activated, the NEO:6 indicator lights up

on the display.

PLIIx MUSIC Suitable for playing any 2-channel stereo

software. You can enjoy wide and deep 7.1-

channel sounds.

PLIIx GAME Suitable for when playing a video game. You

can enjoy 7.1-channel sounds with “being

there” feeling. This mode is available only for

an analog 2-channel signal.

NEO:6 CINEMA Suitable for playing movies. You can get the

same atmosphere with 2-channel software

as with 6.1-channel software. It is also

effective for playing software encoded with

conventional surround formats.

7DTS*

DTS is another digital signal compression method, developed

by Digital Theater Systems, Inc., and enables multi-channel

encoding and decoding (1ch up to 6.1ch).

NEO:6 MUSIC Suitable for playing music software. The

front channel signals bypass the decoder

(resulting in no loss of sound quality) and

the surround signals transmitted through

the other speakers expand the sound field

naturally.

• When DTS signal is detected through the digital input, the

indicator lights up on the display.

DTS Digital Surround

DTS Digital Surround (DTS) is a discrete 5.1-channel digital

audio format available on CD, LD, and DVD software.

Compared to Dolby Digital, the DTS Digital Surround format

has a lower audio compression rate which enables it to add

breadth and depth to the sounds reproduced. As such, DTS

Digital Surround features natural, solid, and clear sound.

DTS Extended Surround (DTS-ES)

* “DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks

of Digital Theater Systems, Inc.

When using Surround mode, the sounds come out of the

activated speakers which the Surround mode requires.

• If either “SURROUND SPK” or “CENTER SPK” is set

to “NO” in the speaker setting (see page 30), the

corresponding channel signals are allocated to and emitted

through the front speakers.

• If both “SURROUND SPK” and “CENTER SPK” are set to

“NO” in the speaker setting (see page 30), JVC’s original

3D-PHONIC processing (which has been developed to create

the surround effect through the front speakers only) is used.

The 3D-PHONIC indicator lights up on the display.

DTS-ES is another multi-channel digital encoding format.

It greatly improves the 360-degree surround impression and

space expression by adding the third surround channel—

surround back channel.

DTS-ES includes two signal formats with different surround

signal recording methods—DTS-ES Discrete 6.1ch (ES

DISCRETE) and DTS-ES Matrix 6.1ch (ES MATRIX).

DTS-ES Discrete 6.1ch has been designed to encode (and

decode) a 6.1-channel signal discretely to avoid interference

with each channel.

DTS-ES Matrix 6.1ch has been designed to add an extra

surround channel to DTS Digital Surround 5.1-channel. By

using a matrix encoding/decoding method, an additional

“surround back” channel signal is encoded (and decoded) in

both the left and right surround channel signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

7Digital Acoustic Processor (DAP) modes

About other digital signals

Linear PCM—Uncompressed digital audio data used for

DVDs, CDs, and Video CDs

You can use the following DAP modes in order to reproduce a

more acoustic sound field in your listening room.

DVDs support 2 channels with sampling rates of 48/96 kHz,

at quantization of 16/20/24 bits. On the other hand, CDs

and Video CDs are limited to 2 channels with 44.1 kHz at 16

bits.

• When Linear PCM signal is detected, the LINEAR PCM

indicator lights up.

HALL1

Reproduces the spatial feeling of a large

shoebox-shaped hall designed primarily for

classical concerts. (Its seating capacity is about

2000.)

HALL2

Reproduces the spatial feeling of a large

vineyard-shaped hall designed primarily for

classical concerts. (Its seating capacity is about

2000.)

Multi-channel PCM—Uncompressed multi-channel digital

audio data used for DVD-Audios

DVD-Audios support up to 5.1 channels with sampling rates

of 44.1/48/88.2/96 kHz and 2 channels with sampling rates

of 44.1/48/88.2/96/176/192 kHz, at quantization of 16/20/24

bits.

• When the Multi-channel PCM signal is detected, the

LINEAR PCM indicator lights up and “MULTI CH PCM”

appears on the display for a while.

LIVE CLUB

Reproduces the spatial feeling of a live music

club with a low ceiling.

DANCE CLUB Reproduces the spatial feeling of a rocking

dance club.

PAVILION

THEATER1

Reproduces the spatial feeling of an exhibition

hall with a high ceiling.

Dual Mono

Reproduces the spatial feeling of a large

theater where the seating capacity is about

600.

Dual Mono can be easily understood when you think of the

bilingual broadcast for TV programs (however, the Dual

Mono format is not identical with those analog formats).

This format is now adopted in Dolby Digital, DTS, and so on.

It allows two independent channels (called main channel

and sub-channel) to be recorded separately.

• You can select either channel you want to listen to (see

page 32).

THEATER2

Reproduces the spatial feeling of a small

theater where the seating capacity is about

300.

NOTE

When “THEATER1” or “THEATER2” is activated while playing back

2-channel analog or digital source, the built-in Dolby Pro Logic II

decoder is activated and the

indicator lights up.

When using the DAP mode, the sounds come out of all the

connected and activated speakers.

• If “SURROUND SPK” is set to “NO” in the speaker setting

(see page 30), JVC’s original 3D-PHONIC processing (which

has been developed to create the surround effect through

the front speakers only) is used.

Introducing the DSP modes

The sound heard in a concert hall, club, etc. consists of direct

sound and indirect sound—early reflections and reflections

from behind. Direct sounds reach the listener directly without

any reflection. On the other hand, indirect sounds are delayed

by the distances of the ceiling and walls. These direct sounds

and indirect sounds are the most important elements of the

acoustic surround effects.

The 3D-PHONIC indicator lights up on the display.

The DSP modes can create these important elements, and

give you a real “being there” feeling.

7MONO FILM

In order to reproduce a more acoustic sound field in your

listening room while viewing monaural sound video software

(analog and 2-channel digital signals including Dual Mono

signal), you can use this mode.

Reflections from behind

Early reflections

The surround effect will be added, and the sound localization

of actor’s words will be improved.

This mode cannot be used for multi-channel digital

signals.

When “MONO FILM” is used, sounds come out of all the

connected (and activated) speakers.

• If “SURROUND SPK” is set to “NO” in the speaker setting

(see page 30), JVC’s original 3D-PHONIC processing (which

has been developed to create the surround effect through

the front speakers only) is used.

Direct sounds

The 3D-PHONIC indicator lights up on the display.

• If incoming signals change from 2-channel digital signal to

another digital signal type, “MONO FILM” is canceled and an

appropriate Surround mode is activated.

The DSP modes include the following modes:

• Digital Acoustic Processor (DAP) modes—HALL1, HALL2,

LIVE CLUB, DANCE CLUB, PAVILION, THEATER1, THEATER2

• MONO FILM—Used for all types of 2-channel signals

(including Dual Mono signal)

• All Channel Stereo mode (ALL CH STEREO)

When one of the DSP modes is activated, the DSP indicator

lights up on the display.

Continued on the next page

Download from Www.Somanuals.com. All Manuals Search And Download.

7All Channel Stereo mode (ALL CH STEREO)

3D HEADPHONE mode

This mode can reproduce a larger stereo sound field using all

the connected (and activated) speakers. This mode cannot

be used if “SURROUND SPK” is set to “NO” in the speaker

setting (see page 30).

If you connect a pair of headphones while one of the

Surround/DSP modes is in use, the 3D HEADPHONE mode

is activated without respect to the type of software played

back.

• “3D HEADPHONE” appears on the display and the DSP

and HEADPHONE indicators light up.

Sound reproduced from

normal stereo

Sound reproduced from

All Channel Stereo mode

Using the Surround/DSP modes

Available Surround/DSP modes vary depending on the speaker settings and the incoming signals. See the table below.

• The numbers inside the parentheses following the incoming signal type indicate the number of the front channels and that of

the surround channels. For example, (3/2) indicates that the signals are encoded with three front signals (left/right/center) and

two (stereo) surround signals.

• For EX/ES/PLIIx setting, see page 32.

EX/ES/PLIIx setting

Incoming Signal Type

AUTO

PLIIx MOVIE

PLIIx MUSIC

OFF

D+PLIIx

MUSIC*²

Dolby Digital Surround EX

Dolby Digital (3/2, 2/2)

DOLBY D EX*^{2, 4}DOLBY D EX*²

DOLBY DIGITAL DOLBY D EX*²

DOLBY DIGITAL

MOVIE*^{1, 2}

D+PLIIx

MOVIE*^{1, 2}

D+PLIIx

MUSIC*²

DOLBY DIGITAL

Dolby Digital (3/1, 2/1, 3/0, 1/0)

Dolby Digital (Dual Mono)

DOLBY DIGITAL

DUAL MONO

DTS+PLIIx

MOVIE*^{1, 2}

DTS+PLIIx

MUSIC*²

DTS-ES Discrete

DTS-ES Matrix

DTS (3/2, 2/2)

DTS-ES DSCRT*²DTS-ES DSCRT*²

DTS SURROUND

DTS-ES

MATRIX*²

DTS-ES

MATRIX*²

DTS+PLIIx

MOVIE*^{1, 2}

DTS+PLIIx

MUSIC*²

DTS+PLIIx

MOVIE*^{1, 2}

DTS+PLIIx

MUSIC*²

DTS SURROUND DTS+NEO:6*²

DTS (3/1, 2/1, 3/0, 1/0)

DTS (Dual Mono)

DTS

DUAL MONO

PLIIx MOVIE*³/

PLII MOVIE/

PLII MUSIC/

PLII GAME/

NEO:6 CINEMA/

NEO:6 MUSIC

PLIIx MUSIC*³/

PLIIx GAME*³/

NEO:6 CINEMA/

NEO:6 MUSIC

Analog/LINEAR PCM/Dolby Digital/

DTS (2/0)

*¹When “S BACK OUT” is set to “1SPK,” “ D+PLIIx MOVIE” is changed to “DOLBY D EX” and “DTS+PLIIx MOVIE” is changed to

“DTS+ EX.”

*²When “S BACK SPK” is set to “NO,” Virtual Surround Back is activated for the modes and the VIRTUAL SB indicator lights up on

the display.

*³When “S BACK SPK” is set to “NO,” “PLllx MOVIE,” “PLllx MUSIC,” and “PLllx GAME” are changed to “PLll MOVIE,” “PLll MUSIC,”

and “PLll GAME.”

*⁴For some Dolby Digital Surround EX software, Dolby Digital 5.1-channel reproduction (“DOLBY DIGITAL”) may be applied even

though you have selected “AUTO.” Select “ON” to apply “DOLBY D EX.”

Download from Www.Somanuals.com. All Manuals Search And Download.

7About the DSP modes

Activating the Surround/DSP modes

• The following DSP modes are available regardless of

incoming signal type:

Available Surround/DSP modes vary depending on the

speaker settings and the incoming signals. For details about

the Surround modes, see page 42.

HALL1, HALL2, LIVE CLUB, DANCE CLUB, PAVILION,

THEATER1, THEATER2

• If multi-channel (more than 2 channels) digital signals are

coming in, “MONO FILM” is not available.

• If “SURROUND SPK” is set to “NO,” “ALL CH STEREO” is not

available.

Activating one of the Surround/DSP modes

automatically recalls the memorized settings and

adjustments.

• To adjust the speaker output level, see page 36.

• When activating one of the Surround/DSP modes, you

can adjust the center tone (see page 38).

• When activating one of the Surround/DSP modes

(except PLIIx MUSIC, PLII MUSIC, NEO:6 MUSIC, and

ALL CH STEREO), you can align the vertical localiztion of

the center channel (see page 38).

• When activating “NEO:6 MUSIC,” you can adjust the

sound localization of the center channel (see page 38).

• When activating the DSP mode (except ALL CH

STEREO), you can adjust the following settings:

– Effect level (see page 37)

Virtual Surround Back

If you have connected (and activated) the surround

speakers, you can use Virtual Surround Back.

This function creates the great surround effect from the

behind without using a surround back speaker as if you

have connected it.

• The VIRTUAL SB indicator lights up on the display.

Virtual Surround Back is activated when selecting any

setting other than “OFF” for the EX/ES/PLIIx setting and

playing back the software including the following signals:

– Dolby Digital Surround EX

– Liveness effect (see page 37)

– Virtual room size (see page 37)

• When activating “PLIIx MUSIC” and “PLII MUSIC,” you

can adjust the following settings:

– DTS-ES

– Dolby Digital or DTS with 4 channels or more

– Center channel localization (see page 38)

– Sound localization position (see page 38)

– Panorama control (see page 37)

7AUTO SURROUND

You can enjoy the Surround mode easily while playing a

digital source.

• For the Surround/DSP mode seleciton, see page 44.

How does “AUTO SURROUND” work?

• If a multi-channel signal comes in, an appropriate

Surround mode will be selected automatically.

• If a Dolby Digital 2-channel signal with surround signal

comes in, “PLIIx MOVIE” or “PLII MOVIE” will be selected.

• If a Dolby Digital 2-channel signal without surround signal

comes in, “SURROUND OFF (stereo)” will be selected.

• If a Linear PCM signal comes in, “SURROUND OFF (stereo)”

will be selected.

• When “AUTO SURROUND” is activated, the AUTO SURR

indicator lights up on the display.

NOTE

“AUTO SURROUND” does not take effect in the following cases:

– While playing an analog source,

– While selecting one of the fixed digital decode mode—“DOLBY

DIGITAL” or “DTS” (see page 22).

Download from Www.Somanuals.com. All Manuals Search And Download.

On the front panel:

7Selecting the Surround/DSP modes

From the remote control:

1, 3

Before you start, remember...

There is a time limit in doing the following steps. If the setting

is canceled before you finish, start from step 2again.

1 Select and play any source.

• Surround/DSP modes are not available when multi-

channel PCM (see page 41) signals recorded in DVD-

Audio are coming. See page 11 for details.

1 Select and play any source.

• Surround/DSP modes are not available when multi-

channel PCM (see page 41) signals recorded in DVD-

Audio are coming in. See page 11 for details.

• Make sure you have selected the audio input setting

(analog or digital) correctly (see page 21).

• Make sure you have selected the audio input setting

(analog or digital) correctly (see page 21).

2 Press SURROUND.

MULTI JOG now works for selecting Surround/DSP modes.

2 Press SURROUND repeatedly to select

the Surround/DSP mode you want.

3 Turn MULTI JOG to select the Surround/

Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital

DSP mode you want.

multi-channel software:

Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital

multi-channel software:

AUTO SURROUND*¹= Surround modes*²= HALL1

= HALL2 = LIVE CLUB = DANCE CLUB = PAVILION

= THEATER1 = THEATER2 = MONO FILM*³=

ALL CH STEREO*⁴= SURROUND OFF =

(Back to the beginning)

AUTO SURROUND*¹Ô Surround modes*²Ô HALL1

Ô HALL2 Ô LIVE CLUB Ô DANCE CLUB Ô

PAVILION Ô THEATER1 Ô THEATER2 Ô MONO

FILM*³Ô ALL CH STEREO*⁴Ô SURROUND OFF Ô

(Back to the beginning)

*¹“AUTO SURROUND” is the initial setting.

*²Available Surround modes vary depending on the

speaker settings and the incoming signals. For details,

see page 42.

*³If an incoming signal is a multi-channel (more than 2

channel) digital signal, “MONO FILM” is not available.

*⁴If “SURROUND SPK” is set to “NO,” “ALL CH STEREO” is

not available.

*¹“AUTO SURROUND” is the initial setting.

*²Available Surround modes vary depending on the

speaker settings and the incoming signals. For details,

see page 42.

*³If an incoming signal is a multi-channel (more than 2

channels) digital signal, “MONO FILM” is not available.

*⁴If “SURROUND SPK” is set to “NO,” “ALL CH STEREO” is

not available.

To cancel Surround/DSP modes

Press SURROUND repeatedly so that “SURROUND OFF”

appears on the display.

To cancel Surround/DSP modes

Turn MULTI JOG so that “SURROUND OFF” appears on the

display.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

•

When connecting the receiver and a TV with the AV COMPU LINK

EX terminal by using a component video cable, you cannot use

Automatic selection of TV input mode (see page 46).

When connecting only the VCR or DVD player to this receiver,

connect it directly to the receiver using a cable with the monaural

mini-plugs.

AV COMPU LINK

remote control

system

You can connect only the TV with AV COMPU LINK EX or AV COMPU

LINK-III terminal to the AV COMPU LINK-III terminal.

7Connections 2: Video cable connection

The AV COMPU LINK remote control system allows you to

operate JVC’s video components (TV, DVD player*, and

VCR) through this receiver.

This receiver is equipped with the AV COMPU LINK-III, which

has added a function to operate JVC’s video components

through the component video jacks. To use this remote

control system, you need to connect the video components

you want to operate, following the diagrams below and the

procedures on page 46.

This receiver is equipped with three types of the video

terminals as well as the HDMI terminals—composite video,

S-video, and component video—and the signals coming into

this receiver through one type of video terminals can output

only through the terminal of the same type. So you need to

connect the video components to this receiver using one of

the following three ways.

• When using the AV COMPU LINK remote control system,

set the video input and video output setting for the DVD

player and the VCR correctly (see “Selecting the video

input setting” on page 21 and “Selecting the output video

signals—VIDEO OUTPUT” on page 34); otherwise, the

correct input for this receiver will not be selected on the TV.

• Refer also to the manuals supplied with your video

components.

* “DVD player” on pages 45 and 46 can be replaced with “DVD

recorder.”

Case 1:

When connecting the source equipment to the receiver

through the S-video terminals, connect this receiver to

the TV video input 1 terminal using S-video cables.

7Connections 1: AV COMPU LINK connection

S-video cable

Source

RX-D412B

equipment

TV video input 1

Monaural mini-plugs (not supplied)

Case 2:

When connecting the source equipment to the receiver

through the composite video jacks, connect this

receiver to the TV video input 2 terminal (composite

video input) using composite video cables.

Monaural mini-plugs

(not supplied)

Composite

video cable

Source

equipment

RX-D412B

TV video input 2

(Composite)

Case 3:

When connecting the source equipment to the receiver

through the component video jacks, connect this

receiver to the TV video input 2 terminals (component

video input) using component video cables.

Component

DVD player

VCR

video cable

Source

equipment

IMPORTANT:

RX-D412B

• The AV COMPU LINK remote control system cannot control

the DBS tuner connected to the DBS IN jacks.

TV video input 2

(Component)

• To use the AV COMPU LINK remote control system, select

“OTHER” for the video output setting (see page 34);

otherwise, the AV COMPU LINK remote control system is

restricted to turning the video component on and off. See

“Automatic power on/off” on page 46.

Download from Www.Somanuals.com. All Manuals Search And Download.

One-touch video play

7Connecting procedure

Simply by inserting a video cassette without its safety tab into

the VCR, you can enjoy the video playback without setting

other switches manually. The receiver automatically turns on

and changes the source to “VCR.”

The TV automatically turns on and changes the input mode

to the appropriate position so that you can view the playback

picture.

1 ^{If you have already plugged your VCR,}

DVD player, TV, and this receiver into the

AC outlets, unplug their AC power cords

first.

2 Connect your VCR, DVD player, TV, and

this receiver, using the cables with the

monaural mini-plugs (not supplied).

• See “Connections 1” on the previous page.

When you insert a video cassette with its safety tab, press the

play (3) button on the VCR or on the remote control. So, you

can get the same result.

One-touch DVD play

Simply by starting playback on the DVD player, you can enjoy

the DVD playback without setting other switches manually.

The following is set automatically:

• Turning on the receiver.

• Changing the source to “DVR/DVD.”

3 Connect the audio input/output jacks

on the VCR, DVD player, TV, and this

receiver using the audio cables.

• See pages 10 to 13.

The TV automatically turns on and changes the input mode

to the appropriate position so that you can view the playback

picture.

4 Connect the video input/output jacks

on the VCR, DVD player, TV, and this

receiver using the S-video cables,

composite video cables, or component

video cables.

Automatic selection of TV input mode

• When you select “TV” as the source to play on the receiver,

the TV automatically changes the input mode to the TV

tuner so that you can watch TV.

• See “Connections 2” on the previous page.

• When you select “DVR/DVD,” “VCR,” or “DBS” as the source

to play on the receiver, the TV automatically changes the

input mode to the appropriate position (either video input 1

or video input 2) so that you can view the playback picture.

5 Plug the AC power cords of the

connected components and this receiver

into the AC outlets.

NOTE

6 When turning on the TV for the first time

after the AV COMPU LINK connection,

turn the TV volume to the minimum

using the TV volume control on the TV.

This function does not work when you connect this receiver and the

TV with the AV COMPU LINK EX terminal using a component video

cable. In this case, reconnect the TV referring to Case 1 or Case 2 on

page 45.

Automatic power on/off

The TV, DVD player, and VCR turn on and off along with the

receiver.

When you turn on the receiver;

• If the previously selected source is “TV” or “DBS,” only the TV

will turn on automatically.

• If the previously selected source is “DVR/DVD,” the TV and

DVD player will turn on automatically.

• If the previously selected source is “VCR,” the TV and VCR

will turn on automatically.

When you turn off the receiver, the TV, DVD player, and VCR

will turn off.

7 Turn on the connected components first,

then turn on this receiver.

• When turning on the VCR, use the remote control

supplied with this receiver (press VCR ).

The AV COMPU LINK remote control system allows you to use

the five basic functions listed below.

Remote control of the TV, DVD player, and VCR using

this remote control

See pages 47 to 51 for details.

• Aim the remote control directly at the remote sensor on

each component.

NOTES

•

When “VIDEO OUTPUT” is set to “HDMI” (see page 34), the AV

COMPU LINK remote control system is restricted to turning the

video component on and off.

If you turn off the receiver while recording on the VCR, the VCR will

not turn off, but continue recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

7VCR

7SIRIUS Satellite Radio

Operating other JVC

products

You can use the supplied remote control to operate not

only this receiver but also other JVC products.

• Refer also to the manuals supplied with the other products.

– Some JVC VCRs can accept two types of the control

signals—remote codes “A” and “B.” This remote control

can operate a VCR whose remote control code is set to “A.”

– Some JVC DVD recorders can accept four types of the

control signals. Select an appropriate code for your DVD

recorder (see page 48).

• To operate other products, aim the remote control directly

at the remote sensor on the target product.

You can always perform the following operation:

Turn on or off the VCR.

VCR

7 TV

After pressing VCR, you can perform the following operations

on the VCR:

CHANNEL +/–:

Change the channel numbers on the VCR.

Select the channel numbers on the VCR.

Start playback.

1 – 9, 0:

Stop playback.

¡:

Pause playback. To release it, press 3.

Fast-forward a tape.

Rewind a tape.

After pressing SIRIUS, you can perform the following

operations on the SIRIUS Satellite Radio:

Turn on or off the SIRIUS Satellite Radio.

TV/SIRIUS

CHANNEL +/–:

Change the channel numbers on the

SIRIUS Satellite Radio.

SELECT:

Select a highlighted item on the display

of the SIRIUS Satellite Radio.

You can always perform the following operations:

CAT 9/( CAT:

Change the category of the program.

MENU:

Enter and exit from the Menu Option

screen of the SIRIUS Satellite Radio.

TV VOL +/–:

TV/VIDEO:

Adjust the volume on the TV.

Change the input mode (either video

input or TV tuner) on the TV.

DISPLAY:

Change the text size on the display of the

SIRIUS Satellite Radio.

After pressing TV, you can perform the following operations

on the TV:

1 – 9, 0, BAND:

MEMORY:

Store or tune in to the preset channel.

Store information on the display of the

SIRIUS Satellite Radio.

Turn on or off the TV.

TV/SIRIUS

CHANNEL +/–:

Change the channel numbers.

DIRECT:

Enable access to channels of the SIRIUS

Satellite Radio directly by numeric

buttons.

1 – 9, 0, 100+ (h10): Select the channel numbers.

RETURN (10):

Switch between the previous channel

and the current channel.

NOTE

Return to the previous channel.

The remote control may not operate a SIRIUS Satellite Radio properly

if it is not KT-SR2000 (JVC SIRIUS Satellite Radio).

Download from Www.Somanuals.com. All Manuals Search And Download.

You can always perform the following operation:

7DVD recorder or DVD player

Turn on or off the DVD recorder or DVD

player.

DVR/DVD

After pressing DVR/DVD, you can perform the following

operations on the DVD recorder and DVD player.

To operate the DVD

recorder, set the mode

selector to “DVR.”

Start playback.

Stop playback.

¢:

Pause playback. To release it, press 3.

Skip to the beginning of the next chapter.

To operate the DVD

player, set the mode

selector to “DVD.”

Return to the beginning of the current (or

previous) chapter.

¡:

Fast-forward playback.

Fast-reverse playback.

TOP MENU/MENU: Display the menu recorded on discs.

5/∞/3/2:

Select an item on the menu screen.

SET:

Enter the selected item, channel number,

chapter/title number, or track number (if

required).

After setting the mode selector correctly, you can perform

the following operations on the DVD recorder or DVD player.

See the manual supplied with the DVD recorder or DVD

player for details.

Only for DVD recorder operations:

CHANNEL +/–:

Change the TV channel numbers on the

DVD recorder.

1 – 9, 0:

Select a TV channel number (while

stopped) or a chapter/title number, track

number (while playing back). Press SET to

enter the number.

To change the remote control code for DVD recorder

Some JVC DVD recorders can accept four types of control

signals. You can assign one of the four codes to the remote

control supplied for this receiver to operate your DVD

recorder. For details, refer to the manual supplied with the

DVD recorder.

Only for DVD player operations:

1 – 10, 0, h10: Select a chapter/title number, track

Initial setting: 3

number, menu item, etc.

1 Set the mode selector to “DVR.”

2 Press and hold DVR/DVD

If these buttons do not function normally, use the

remote control supplied with your DVD recorder or DVD

player. Refer also to the manual supplied with the DVD

recorder or DVD player for details.

• Keep the button pressed until step 4 is finished.

3 Press DVR/DVD.

4 Enter the remote control code you want

using the numeric buttons (1 – 4, 0).

EX.: To enter the code “2,” press 0, then 2.

Code for DVR

Number to enter

5 Release DVR/DVD

Now, the remote control code has been changed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Manufacturer codes for TV:

Manufacturer Codes

JVC

Operating other

manufacturers’

products

Akai

Bell+Howell

Centurion

Coronad

Daewoo

Emerson

Fisher

06, 07, 08

09, 10, 11, 12, 13

By changing the transmittable signals, you can use the

supplied remote control to operate other manufacturers’

products.

• Refer also to the manuals supplied with the other products.

• To operate those components with the remote control, first

you need to set the manufacturer codes each for the TV,

VCR, CATV converter, DBS tuner, and DVD player.

• After replacing the batteries of the remote control, set the

manufacturer codes again.

GE•Pana

GE•RCA

Gold Star

Hitachi

15, 16

18, 19

20, 21

KTV

22, 23

Magnavox

Marantz

Mitsubishi

Panasonic

Philips

• All the functions may not be assigned to the buttons for

some equipment.

To change the transmittable signals for operating a TV

26, 27

1 Press and hold TV/SIRIUS

• Keep the button pressed until step 3 is finished.

Pioneer

Proscan

Quasar

2 Press TV.

3 Enter the manufacturer code using the

Radioshack

RCA

numeric buttons (1 – 9, 0).

02, 17, 32, 33, 34, 35

See “Manufacturer codes for TV” on the right.

Samsung

Sanyo

36, 37, 45, 46, 47, 48

4 Release TV/SIRIUS

Now, you can perform the following operations on the TV:

Sears

Sharp

39, 49, 50

TV VOL +/–:

TV/VIDEO:

Adjust the volume on the TV.

Sony

Change the input mode (either

video input or TV tuner) on the TV.

Symphonic

Toshiba

Zenith

41, 42

After pressing TV, you can perform the following

operations on the TV:

43, 44

Turn on or off the TV.

TV/SIRIUS

Initial setting: 01

CHANNEL +/–:

Change the channel numbers.

1 – 9, 0, 100+ (h10): Select the channel numbers.

See the manual supplied with the TV for details.

Manufacturer codes are subject to change without

notice. If they are changed, this remote control cannot

operate the equipment.

5 Try to operate your TV by pressing TV/

SIRIUS

Your TV turns on or off when you have entered the correct

code.

If more than one code is listed for your brand of TV, try

each one until the correct one is entered.

Download from Www.Somanuals.com. All Manuals Search And Download.

To change the transmittable signals for operating a VCR

Manufacturer codes for VCR:

Manufacturer Codes

JVC

1 Press and hold VCR

01, 02, 03, 04

• Keep the button pressed until step 3 is finished.

Aiwa

2 Press VCR.

Akai

06, 07, 08

Bell+Howell

Daewoo

Emerson

Fisher

3 Enter the manufacturer code using the

numeric buttons (1 – 9, 0).

See “Manufacturer codes for VCR” on the right.

11, 12, 13, 14, 15

16, 17, 18, 19

4 Release VCR

G.E.

20, 21

Now, you can perform the following operation on the VCR:

Go Video

Gold Star

Go-Video A

Go-Video B

Hitachi

Magnavox

Mitsubishi

NEC

Turn on or off the VCR.

VCR

After pressing VCR, you can perform the following

operations on the VCR:

CHANNEL +/–:

Change the TV channel numbers on

the VCR.

20, 26

27, 28, 29

1 – 10, 0, h10:

Select the TV channel numbers on

the VCR.

30, 31, 32, 33

Start playback.

34, 35

¡:

Stop playback.

Panasonic

Philips

36, 37

Pause playback. To release it, press 3.

Fast-forward a tape.

Rewind a tape.

RCA

Samsung

Sanyo

39, 40, 41

16, 17, 18, 19

See the manual supplied with the VCR for details.

Scott

5 Try to operate your VCR by pressing VCR

Sharp

43, 44

Shintom

Sony

Your VCR turns on or off when you have entered the

correct code.

46, 47, 48, 49, 50, 51

Symphonic

Teknica

Toshiba

Zenith

If more than one code is listed for your brand of VCR, try

each one until the correct one is entered.

53, 54

Initial setting: 01

Manufacturer codes are subject to change without

notice. If they are changed, this remote control cannot

operate the equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

To change the transmittable signals for operating a CATV

converter or DBS tuner

To change the transmittable signals for operating a DVD

player

1 Press and hold DBS/CATV

1 Set the mode selector to “DVD.”

• Keep the button pressed until step 3 is finished.

2 Press and hold DVR/DVD

2 Press DBS.

• Keep the button pressed until step 4 is finished.

3 Enter the manufacturer code using the

3 Press DVR/DVD.

numeric buttons (1 – 9, 0).

4 Enter the manufacturer code using the

See “Manufacturer codes for CATV converter” or

“Manufacturer codes for DBS tuner” below.

numeric buttons (1 – 9, 0).

See “Manufacturer codes for DVD player” below.

4 Release DBS/CATV

5 Release DVR/DVD

Now, you can perform the following operation on the

CATV converter or DBS tuner:

Now, you can perform the following operations on the

DVD player:

Turn on or off the CATV converter or

DBS tuner.

DBS/CATV

Turn on or off the DVD player.

Start playback.

DVR/DVD

¢:

After pressing DBS, you can perform the following

operations on the CATV converter or DBS tuner:

Skip to the beginning of the next

chapter (or fast-forward for some

models).

Return to the beginning of the

current chapter (or fast-reverse for

some models).

CHANNEL +/–:

Change the channel numbers on the

CATV converter or DBS tuner.

Select the channel numbers on the

CATV converter or DBS tuner.

1 – 10, 0:

Stop playback.

Pause playback. To release it, press 3.

See the manual supplied with the CATV converter or DBS

tuner for details.

MENU:

Display the menu recorded on DVD

VIDEO discs.

Select an item on the menu screen.

Enter the selected item.

5 Try to operate your CATV converter or

DBS tuner by pressing DBS/CATV

5/∞/3/2:

SET:

When your CATV converter or DBS tuner turns on or off,

you have entered the correct code.

1 – 9, 0, h10:

Select the chapter number.

See the manual supplied with the DVD player for details.

If more than one code is listed for your brand of CATV

converter or DBS tuner, try each one until the correct one is

entered.

6 Try to operate your DVD player by

pressing DVR/DVD

Manufacturer codes for CATV converter:

Your DVD player turns on or off when you have entered

the correct code.

Manufacturer

G.I.

Gemini

Hamlin

Jerrold

Macom

Magnavox

Oak

Panasonic

Philips

Codes

Manufacturer codes for DVD player:

03, 04, 05, 06

07, 08, 09, 10, 11, 12, 13, 14, 15

Manufacturer

JVC

Codes

16, 17, 18

20, 21, 22

23, 24

Hitachi

Kenwood

Magnavox

Marantz

Mitsubishi

Onkyo

03, 04

08, 09

25, 26, 27, 28, 29, 30

Pioneer

S. Atlanta

Samsung

Tocom

31, 32

33, 34, 35

38, 39

Panasonic

Philips

Pioneer

Proscan

RCA

Zenith

Manufacturer codes for DBS tuner:

Samsung

Sony

Manufacturer

Echostar

G.I.

Codes

Toshiba

Yamaha

Zenith

05, 16

Hitachi

Hughes

Panasonic

Primestar

RCA

Sony

Toshiba

Initial setting: 01

NOTE

You cannot use this remote control to operate any manufacturers’

DVD recorders other than JVC’s.

Manufacturer codes are subject to change without

notice. If they are changed, this remote control cannot

operate the equipment.

Initial setting: 01

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Use this chart to help you solve daily operational problems.

If there are any problems you cannot solve, contact your JVC

service center.

For Precise Surround Setup and XM Satellite Radio

operations, see the separated troubleshooting on pages

19 and 28.

PROBLEM

POSSIBLE CAUSE

The power cord is not plugged in.

SOLUTION

The power does not come on.

Plug the power cord into an AC outlet.

The receiver turns off (enters

standby mode).

Speakers are overloaded because of high 1. Stop the playback source.

volume.

2. Turn on the receiver again, then turn

the volume down.

Speakers are overloaded because of a

short circuit at the speaker terminals.

Check the speaker wiring. If the speaker

wiring is not short-circuited, contact your

dealer.

The receiver is overloaded because of

high voltage.

Consult your dealer after unplugging the

power cord.

“OVER HEAT” flashes on the

display, then the receiver turns

off.

The receiver is overloaded because of

high volume or long time usage.

Turn the volume down or turn off the

receiver for a while and turn it on again.

If the receiver turns off soon after doing

solutions above, consult your dealer after

unplugging the power cord.

No sound from speakers.

Speaker signal cables are not connected. Check the speaker wiring, then reconnect

if necessary (see page 8) after unplugging

the power cord.

Connections are incorrect.

Check the audio connections (see pages

9 to 15) after unplugging the power cord.

An incorrect source is selected.

Muting is activated.

Select the correct source.

Press MUTING to cancel the mute (see

page 22).

An incorrect input mode (analog or

digital) is selected.

Select the correct input mode (analog or

digital).

Sound from one speaker only.

Speaker signal cables are not connected

properly.

Check the speaker wiring and reconnect

if necessary (see page 8) after unplugging

the power cord.

Sounds are intermittently

When you use the digital coaxial

This is not a malfunction.

distorted by the outside noise

such as a lightning discharge.

connection, the sounds may be

intermittently distorted by the outside

noise such as a lightning discharge but

the sound will be restored automatically.

No picture on the TV screen.

HDMI signals do not come on.

Either the video input setting or video

output setting is incorrect.

Select the correct settings (see page 21

or 34).

A video or audio format incompatible

with this receiver and/or TV is played.

Check the video or audio format of the

signal to see if it is compatible with this

receiver and/or TV.

An HDCP-compatible TV is not

connected.

Connect an HDCP-compatible TV.

The receiver failed to recognize HDMI-

connected components.

Disconnect the HDMI cable and connect

it again after unplugging the power cord.

An HDMI cable longer than 5 m (15 ft) is

used.

Use an HDMI cable shorter than 5 m (15

ft) to assure stable operation and picture

quality.

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The remote control does not

operate as you intend.

The remote control is not ready for your

intended operation.

Set the mode selector correctly, then

press the corresponding source selecting

button before operation.

The remote control does not

work.

There is an obstruction blocking the

remote sensor on the receiver.

Remove the obstruction.

Batteries are weak.

Replace batteries.

The mode selector is set to the incorrect

position.

Set the mode selector to the proper

position.

Continuous hiss or buzzing

during FM reception.

Incoming signal is too weak.

Connect an outdoor FM antenna (not

supplied) after unplugging the power

cord, or contact your dealer.

The station is too far away.

Select another station.

A wrong antenna is being used.

Check with your dealer to be sure you

have the correct antenna.

Antennas are not connected properly.

Check the connections.

Occasional cracking noise during Ignition noise from automobiles.

FM reception.

Move the antenna farther from

automobile traffic.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Designs and specifications are subject to change without

notice.

7Amplifier

Output Power

At stereo operation:

Front channels:

110 W per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 0.8% total

harmonic distortion.

At surround operation:

Front channels:

110 W per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 0.8% total

harmonic distortion.

Center channel:

110 W, min. RMS, driven into 6 Ω at 1 kHz, with no more than 0.8% total harmonic

distortion.

Surround channels:

Surround back channels:

110 W per channel, min. RMS, driven into 6 Ω at 1 kHz, with no more than 0.8% total

harmonic distortion.

110 W per channel, min. RMS, driven into 6 Ω at 1 kHz, with no more than 0.8% total

harmonic distortion.

Audio

Audio Input Sensitivity/Impedance:

DVR/DVD, VCR, DBS, TV:

300 mV/47 kΩ

0.5 V(p-p)/75 Ω

Audio Input (DIGITAL IN)*:

Coaxial: DIGITAL IN 1(DVR/DVD):

Optical: DIGITAL IN 2(DBS), 3(VCR): –21 dBm to –15 dBm (660 nm 30 nm)

USB: USB

* Corresponding to Linear PCM, Dolby Digital, and DTS (with sampling frequency—32 kHz, 44.1 kHz, 48 kHz).

Audio Output Level:

DVR, VCR:

300 mV

Signal-to-Noise Ratio (’66 IHF/’78 IHF):

Frequency Response (6 Ω):

Bass Boost:

80 dB/70 dB

20 Hz to 20 kHz ( 1 dB)

+4 dB 1 dB at 100 Hz

Equalization (at DSP operation):

Center frequency:

63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz

8 dB

Control range:

Video

Video Input Sensitivity/Impedance:

Composite video: DVR/DVD, VCR, DBS:

S-video: DVR/DVD, VCR, DBS:

Y (luminance):

1 V(p-p)/75 Ω

C (chrominance, burst):

Component: DVR/DVD, VCR (DBS):

Y (luminance):

0.286 V(p-p)/75 Ω

1 V(p-p)/75 Ω

PB, PR:

0.7 V(p-p)/75 Ω

Video Output Level/Impedance:

Composite video: DVR, VCR, MONITOR OUT:

S-video: DVR, VCR, MONITOR OUT:

Y (luminance):

1 V(p-p)/75 Ω

C (chrominance, burst):

Component: MONITOR OUT:

Y (luminance):

0.286 V(p-p)/75 Ω

1 V(p-p)/75 Ω

0.7 V(p-p)/75 Ω

Negative

PB, PR:

Synchronization:

Download from Www.Somanuals.com. All Manuals Search And Download.

7HDMI

HDMI Input (Ver. 1.1):

HDMI Output (Ver. 1.0):

VCR(DBS), DVR/DVD

MONITOR OUT

7FM tuner (IHF)

Tuning Range:

87.5 MHz to 108.0 MHz

Usable Sensitivity:

Monaural:

12.8 dBf (1.2 μV/75 Ω)

50 dB Quieting Sensitivity:

Monaural:

16.0 dBf (1.7 μV/75 Ω)

37.5 dBf (20.5 μV/75 Ω)

35 dB at 1 kHz

Stereo:

Stereo Separation at OUT (REC):

7AM tuner

Tuning Range:

530 kHz to 1 710 kHz

7General

Power Requirements:

Power Consumption:

AC 110 V/127 V/220 V/230 V – 240 V , adjustable with the voltage selector, 50Hz/60 Hz

180 W (at operation)

5.8 W (in standby mode)

Dimensions (W x H x D):

Mass:

435 mm x 91.5 mm x 371 mm

6.9 kg

Download from Www.Somanuals.com. All Manuals Search And Download.

Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, and U.K.)

CAUTION for mains (AC) line

BEFORE PLUGGING IN, do check that your mains

(AC) line voltage corresponds with the position of

the voltage selector switch provided on the outside

of this equipment and, if different, reset the voltage

selector switch, to prevent from a damage or risk

of fire/electric shock.

0706RYMMDWJEIN

Download from Www.Somanuals.com. All Manuals Search And Download.

Intel Stereo Amplifier ReValver MK III User Manual
Invacare Mobility Aid MK6i User Manual
Jenn Air Cooktop W10204447A User Manual
JVC MP3 Player Accessories UX A52R User Manual
Kenwood Home Security System NX 410 User Manual
Kenwood Speaker KFC 1271 User Manual
Kenwood Stereo System VR 9070 User Manual
KitchenAid Dishwasher KUDC02IR User Manual
KitchenAid Range YKGRT500 User Manual
KLH Speaker RSP800 User Manual