JVC Stereo Receiver RX 730RBK User Manual
AUDIO/VIDEO CONTROL RECEIVER  
AUDIO/VIDEO-RECEIVER MIT STEUEREINHEIT  
AMPLI/TUNER DE COMMANDE AUDIO/VIDEO  
GEINTEGREERDE AUDIO/VIDEO-VERSTERKER  
RECEPTOR DE CONTROL DE AUDIO/VÍDEO  
RICEVITORE DI CONTROLLO AUDIO/VIDEO  
RX-730RBK  
SEND/LEARN  
ERROR  
TV  
VCR  
AUDIO  
SLEEP  
SEQUENTIAL PROGRAM KEY  
A
B
C
ONE TOUCH  
OPERATION  
SOURCE SELECT  
VIDEO  
1
VIDEO  
2
VCR  
SURROUND TV SOUND  
MODE  
FM  
CD  
AM  
SEA  
TAPE  
PHONO  
MASTER VOLUME  
MODE  
RX-730R AUDIO/VIDEO CONTROL RECEIVER  
AM  
VIDEO1  
VIDEO2  
VCR  
TV SOUND  
FM  
CD  
PHONO  
TAPE  
MENU  
ONE TOUCH  
OPERATION  
–
+
SOURCE  
MENU  
EXIT  
MUTE  
SURROUND MODE  
SEA MODE  
ON SCREEN CONTROL  
SURROUND  
ADJUST  
SEA  
MEMORY  
MEMORY  
ADJUST  
L
BALANCE  
R
VOLUME  
SETTING  
TUNER  
VIDEO  
2
SPEAKERS  
PHONES  
STANDBY  
VIDEO  
L
AUDIO  
R
1
2
POWER  
DISPLAY MODE  
TA/NEWS/INFO  
EON  
PTY SEARCH  
_ON —OFF  
STANDBY/ON  
_ON —OFF  
RM-SR730RU REMOTE CONTROL  
INSTRUCTIONS  
For Customer Use:  
BEDIENUNGSANLEITUNG  
MANUEL D’INSTRUCTIONS  
GEBRUIKSAANWIJZING  
MANUAL DE INSTRUCCIONES  
ISTRUZIONI  
Enter below the Model No. and Serial  
No. which are located either on the rear,  
bottom or side of the cabinet. Retain this  
information for future reference.  
Model No.  
Serial No.  
LET0054-001A  
[EF, G]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION  
VOORZICHTIG  
To reduce the risk of electrical shocks, fire, etc.:  
1. Do not remove screws, covers or cabinet.  
2. Do not expose this appliance to rain or moisture.  
Ter vermindering van gevaar voor brand, elektrische schokken, enz.:  
1. Verwijder geen schroeven, panelen of de behuizing.  
2. Stel dit toestel niet bloot aan regen of vocht.  
PRECAUCIÓN  
ACHTUNG  
Para reducir riesgos de choques eléctricos, incendio, etc.:  
1. No extraiga los tornillos, los cubiertas ni la caja.  
2. No exponga este aparato a la lluvia o a la humedad.  
Zur Verhinderung von elektrischen Schlägen, Brandgefahr, usw:  
1. Keine Schrauben lösen oder Abdeckungen enternen und nicht  
das Gehäuse öffnen.  
2. Dieses Gerät weder Regen noch Feuchtigkeit aussetzen.  
ATTENZIONE  
ATTENTION  
Per ridurre il rischio di scosse elettriche, incendi, ecc...  
1. Non togliere viti, coperchi o la scatola.  
2. Non esporre l’apparecchio alla piogggia e all’umidità.  
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:  
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret  
de l’appareil.  
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.  
G-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Voorzichtig ––  
Dit apparaat is voorzien van een  
POWER en STANDBY/ON  
schakelaars!  
Caution ––  
This apparatus is provided with a  
POWER switch and STANDBY/ON  
button!  
POWER hoofdschakelaar om het  
POWER switch to be able to  
apparaatgebruiksklaartezetten,maartezorgendathetstroomverbruik  
minimaal blijft. Neem in verband hiermee het volgende in acht:  
1. Bij de eerste ingebruikneming zorgt u eerst dat alle aansluitingen  
in orde zijn, dan steekt u de stekker in het stopkontakt en dan zet  
minimize power consumption for safe use. Therefore,  
1. When doing initial setting, complete all the connections required,  
connect the mains plug into the wall outlet, and set the POWER  
switch to ON. After these, it will be available to operate STANDBY/  
u de  
POWER schakelaar in de “ON” stand. Daarna kunt u het  
ON  
2. When not in use, set the  
3. Disconnect the mains plug to shut the power off completely. The  
button and so on.  
apparaat aan- en uitschakelen met de STANDBY/ON  
schakelaar.  
POWER switch to OFF.  
2. Wanneer u het apparaat geruime tijd niet gebruikt, kunt u beter de  
POWER schakelaar in de “OFF” stand zetten.  
3. Om de stroomtoevoer geheel uit te schakelen, trekt u de stekker  
uit het stopkontakt. Anders zal er altijd een geringe hoeveelheid  
stroom naar het apparaat lopen, ongeacht de stand van de  
POWER switch and STANDBY/ON  
do not disconnect the mains line.  
button in any position  
4. The power can be remote controlled.  
Achtung ––  
POWER-Schalter und STANDBY/ON  
-Taste!  
STANDBY/ON  
en de POWER.  
Dieses Gerät hat einen Netzschalter ( POWER), um den  
Stromverbrauch für sichere Verwendung auf ein Minimum bringen zu  
können. Verfahren Sie deshalb wie folgt:  
1. Beim ursprünglichen Aufbau alle erforderlichen Anschlüsse  
herstellen, den Netzstecker in eine Wandsteckdose stecken, und  
4. U kunt het apparaat ook met de afstandsbediening aan- en  
uitschakelen.  
Precaución –– Interruptor  
POWER y botón STANDBY/ON  
!
Esta unidad dispone de un interruptor  
POWER que sirve para  
reducir al mínimo el consumo de alimentación para proporcionar  
mayor seguridad operacional. Por lo tanto,  
den  
POWER-Schalter einschalten. Anschließend ist Betrieb  
-Taste usw. möglich.  
der STANDBY/ON  
1. Al ejecutar el ajuste inicial, después de completar todas las  
conexiones requeridas, conectar el cable de alimentación a una  
toma de pared, y activar el interruptor POWER. Entonces, será  
posible ejecutar operaciones tales como la conmutación del  
estado de alimentación.  
2. Wenn das Gerät nicht verwendet wird, den  
ausschalten.  
3. Den Netzstecker aus der Steckdose ziehen, um die  
Stromversorgung vollkommen zu unterbrechen. Der POWER-  
POWER-Schalter  
Schalter und die STANDBY/ON  
-Taste unterbrechen in keiner  
2. Desactivar el interruptor  
uso.  
POWER al dejar la unidad fuera de  
Stellung die Stromversorgung vollkommen.  
4. Die Stromversorgung kann mit der Fernbedienung ein- und  
ausgeschaltet werden.  
3. Desconectar el cable de alimentación para desactivar la  
alimentación totalmente. Cualquier que sea la posición de ajustes  
del interruptor  
alimentación no es cortada completamente.  
4. La alimentación puede ser controlada remotamente.  
POWER y el botón STANDBY/ON  
, la  
Attention — Commutateur POWERetd’unetoucheSTANDBY/  
ON  
!
Cetappareilestéquipéd’uncommutateur POWERquiluipermetde  
réduire sa consommation d’électricité pour une utilisation plus sûre.  
Par conséquent,  
1. En procédant au réglage initial, compléter toutes les connexions  
nécessaires, connecter la fiche secteur dans la prise murale et  
mettre le commutateur POWER sur la position ON. Ensuite, il  
Attenzione –– Interruttore  
Per ridurre al minimo l’assorbimento di corrente ai fini della sicurezza,  
POWER e tasto STANDBY/ON  
!
questo apparecchio è stato dodato di un interruttore  
conseguenza,  
1. Al momento dell’impostazione iniziale, completare tutti i  
collegamenti richiesti, inserire la spina del cavo di alimentazione  
nella presa a muro della rete elettrica e impostare l’interruttore  
POWER in posizione ON. Fatto ciò, sarà pronto all’uso  
POWER. Di  
sera possible de contrôler la touche STANDBY/ON  
, etc.  
2. Mettre le commutateur  
l’appareil n’est pas utilisé.  
POWER sur la position OFF lorsque  
STANDBY/ON  
.
3. Déconnecterlafichesecteurpourcoupercomplètementlecourant.  
Le commutateur POWER et la touche STANDBY/ON ne  
coupent jamais complètement l’alimentation, quelle que soit leurs  
positions.  
4. L’alimentation peut être télécommandée.  
2. Quandononinuso,impostarel’interruttore POWER inposizione  
OFF.  
3. Disinserirelaspinadelcavodialimentazionedallapresadellarete  
elettricaperstaccarecompletamentel’alimentazione.L’interruttore  
POWER e il tasto STANDBY/ON  
in nessuna posizione  
staccano la linea di alimentazione elettrica principale.  
4. È possibile il controllo remoto dell’alimentazione.  
G-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caution: Proper Ventilation  
Voorzichtig: Zorg Voor Goede Ventilatie  
To avoide risk of electric shock and fire and to protect from damage.  
Locate the apparatus as follows:  
Om gevaar voor brand of een elektrische schok te voorkomen, dient u  
bij opstelling van het apparaat op de volgende punten te letten:  
Front:  
Sides:  
Top:  
Back:  
Bottom:  
No obstructions open spacing.  
Voorkant:  
Zijkanten:  
Voldoende ruimte vrij houden.  
Minstens 10 cm aan weerszijden vrij houden.  
No obstructions in 10 cm from the sides.  
No obstructions in 10 cm from the top.  
No obstructions in 15 cm from the back  
No obstructions, place on the level surface.  
Bovenkant: Niets bovenop plaatsen; 10 cm speling geven.  
Achterkant: Minstens 15 cm ruimte achteraan vrij houden.  
Onderkant: Opstellen op een egaal horizontaal oppervlak.  
Bovendien moet er rondom voldoende luchtdoorstroming zijn, zoals in  
de afbeelding aangegeven.  
In addition, maintain the best possible air circulation as illustrated.  
Achtung: Angemessene Ventilation  
Stellen Sie das Gerät zur Verhütung von elektrischem Schlag und  
Feuer und zum Schutz gegen Beschädigung wie folgt auf:  
Vorderseite: Offener Platz ohne Hindernisse.  
Precaución: Ventilación Adecuada  
Para evitar el riesgo de choque eléctrico e incendio y para proteger el  
aparato contra daños.  
Seiten:  
Keine Hindernisse innerhalb 10 cm von den Seiten.  
Ubique el aparato de la siguiente manera:  
Oberseite: Keine Hindernisse innerhalb 10 cm von der Oberseite.  
Rückseite: Keine Hindernisse innerhalb 15 cm von der Rückseite.  
Unterseite: Keine Hindernisse. Auf eine ebene Oberfläche stellen.  
Zusätzlich die bestmögliche Luftzirkulation wie gezeigt erhalten.  
Frente:  
Lados:  
Espacio abierto sin obstrucciones  
10 cm sin obstrucciones a los lados  
Parte superior: 10 cm sin obstrucciones en la parte superior  
Parte trasera: 15 cm sin obstrucciones en la parte trasera  
Fondo:  
Sin obstrucciones, colóquelo sobre una superficie  
nivelada  
Attention: Ventilation Correcte  
Pour éviter les chocs électriques, l’incendie et tout autre dégât.  
Disposer l’appareil en tenant compte des impératifs suivants  
Además, mantenga la mejor circulación de aire posible como se  
ilustra.  
Avant:  
Rien ne doit gêner le dégagement  
Laisser 10 cm de dégagement latéral  
Laisser 10 cm de dégagement supérieur  
Laisser 15 cm de dégagement arrière  
Rien ne doit obstruer par dessous; poser l’appareil sur  
une surface plate.  
Flancs:  
Dessus:  
Arrière:  
Dessous:  
Attenzione: Problemi di Ventilazione  
Per evitare il rischio di folgorazioni ed incendi e proteggere l’unità da  
danni, installarla nel modo seguente.  
Davanti:  
Lati:  
Sopra:  
Retro:  
Fondo:  
Nessun ostacolo, spazio libero  
Nessun ostacolo per almeno 10 cm  
Nessun ostacolo per almeno 10 cm  
Nessun ostacolo per almeno 15 cm  
Libero ed in piano  
Veiller également à ce que l’air circule le mieux possible comme  
illustré.  
Inoltre, mantenere il più possibile la circolazione dell’aria.  
Spacing 15 cm or more  
Abstand von 15 cm oder mehr  
Dégagement de 15 cm ou plus  
Minstens 15 cm tussenruimte  
Espacio de 15 cm o más  
15 cm di distanza o più  
Front  
Vorderseite  
Avant  
Voorkant  
Frente  
RX-730RBK  
Davanti  
Wall or obstructions  
Wand oder Hindernisse  
Mur, ou obstruction  
Wand of meubilair  
Pared u obstrucciones  
Parete o ostacol  
Stand height 15 cm or more  
Standhöhe 15 cm oder mehr  
Hauteur du socle: 15 cm ou plus  
Standard op minstens 15 cm van de vloer  
Allura del soporte 15 cm o más  
Altezza del tavolino 15 cm p plù  
Floor  
Boden  
Plancher  
Vloer  
Piso  
Pavimento  
G-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Getting Started........................................................................................................................... 2  
Before Installation .................................................................................................................... 2  
Checking the Supplied Accessories ......................................................................................... 2  
Switches, Buttons and Controls ............................................................................................... 3  
Connecting the FM and AM (MW/LW) Antennas .................................................................. 5  
Connecting the Speakers .......................................................................................................... 6  
Connecting Audio/Video Components .................................................................................... 9  
Connecting the Power Cord ................................................................................................... 11  
Putting Batteries in the Remote Control ................................................................................ 11  
Basic Operations ...................................................................................................................... 12  
Turning the Power On and Off .............................................................................................. 12  
Selecting the Source to Play................................................................................................... 12  
Adjusting the Volume ............................................................................................................ 13  
Selecting the Front Speakers .................................................................................................. 13  
Muting the Sound ................................................................................................................... 14  
Recording a Source ................................................................................................................ 14  
Basic Settings ........................................................................................................................... 15  
Adjusting the Front Speaker Output Balance ........................................................................ 15  
Listening at Low Volume (Loudness) ................................................................................... 15  
Using the Sleep Timer............................................................................................................ 16  
Selecting the Center Speaker Size ......................................................................................... 17  
Using Visual Confirmation .................................................................................................... 18  
One Touch Operation.............................................................................................................. 19  
About the One Touch Operation ............................................................................................ 19  
Using the One Touch Operation ............................................................................................ 19  
Receiving Radio Broadcasts ................................................................................................... 20  
Tuning in Stations Manually .................................................................................................. 20  
Using Preset Tuning ............................................................................................................... 20  
Selecting the FM Reception Mode......................................................................................... 21  
Assigning Names to Preset Stations....................................................................................... 22  
Using the RDS (Radio Data System) to Receive FM Stations .............................................. 23  
What Information Can RDS Signals Provide?....................................................................... 23  
Searching for a Program by PTY Codes ................................................................................ 24  
Switching to a Broadcast Program of Your Choice Temporarily .......................................... 26  
Using the SEA Modes .............................................................................................................. 27  
Selecting Your Favorite SEA Mode ...................................................................................... 27  
Creating Your Own SEA Mode ............................................................................................. 28  
Using the Surround Processor................................................................................................ 29  
Using JVC’s Hall Surround ................................................................................................... 29  
Speaker Arrangements for Dolby Surround........................................................................... 31  
Preparing for Dolby Surround................................................................................................ 32  
Using Dolby Surround ........................................................................................................... 36  
Using the On-Screen Display to Control the Receiver ......................................................... 37  
COMPU LINK Remote Control System ............................................................................... 41  
Using the Remote Control....................................................................................................... 42  
Using the Remote Control for Operating JVC Audio/Video Components............................ 42  
Simplifying the Operations Using the Remote Control ......................................................... 45  
Operating the Other Manufacturers’ Audio/Video Components ........................................... 47  
Troubleshooting ....................................................................................................................... 50  
Specifications............................................................................................................................ 51  
Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting Started  
Thissectionexplainshowtoconnectaudio/videocomponentsandspeakerstothereceiver,andhowtoconnect  
the power supply.  
Before Installation  
General  
• Be sure your hands are dry.  
• Turn the power off to all components.  
• Read the manuals supplied with the components you are going to connect.  
Locations  
• Install the receiver in a location that is level and protected from moisture.  
• The temperature around the receiver must be between –5˚ and 35˚ C (23˚ and 95˚ F).  
• Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and  
damage the receiver.  
Handling the receiver  
• Do not insert any metal object into the receiver.  
• Do not disassemble the receiver or remove screws, covers, or cabinet.  
• Do not expose the receiver to rain or moisture.  
Checking the Supplied Accessories  
Check to be sure you have all of the following items, which are supplied with the receiver.  
The number in the parenthesis indicates the quantity of the pieces supplied.  
• Remote Control (1)  
• Batteries (2)  
• AM (MW/LW) Loop Antenna (1)  
• FM Antenna (1)  
If anything is missing, contact your dealer immediately.  
Page 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switches, Buttons and Controls  
Become familiar with the main switches and controls on your receiver before use.  
Front Panel  
7
6
1
2
3
4
5
8
MASTER VOLUME  
RX-730R AUDIO/VIDEO CONTROL RECEIVER  
VIDEO1  
VIDEO2  
VCR  
TV SOUND  
FM  
AM  
CD  
PHONO  
TAPE  
ONE TOUCH  
OPERATION  
–
+
SOURCE  
SURROUND MODE  
SEA MODE  
SURROUND  
ADJUST  
SEA  
MEMORY  
MEMORY  
ADJUST  
SETTING  
TUNER  
STANDBY  
VIDEO  
2
SPEAKERS  
PHONES  
POWER  
DISPLAY MODE  
TA/NEWS/INFO  
PTY SEARCH  
EON  
L
R
1
2
VIDEO  
AUDIO  
_ON —OFF  
STANDBY/ON  
_ON —OFF  
q
w
e
r
;
d
p
u
o
9
s
a
t
y
i
Refer to the pages in parentheses for details.  
Front Panel  
1 Remote sensor (11)  
2 Display (12)  
3 ONE TOUCH OPERATION button and lamp (19)  
4 MASTER VOLUME control (13)  
5 SURROUND MODE button and lamp (29, 32, 36)  
6 SOURCE button and lamps (12)  
7 SEA MODE button and lamp (27)  
8 MEMORY button for SEA adjustments (28)  
IMPORTANT  
To use Control % / fi / @ / # buttons (i) on the front  
panel:  
What these buttons actually do depends on which function  
you are trying to adjust. Before using these buttons, select  
the function by pressing one of the function selecting  
buttons (5, 6, 7, t, y, ;, d), and being sure its lamp is  
lit.  
9 STANDBY/ON  
button and STANDBY lamp (12)  
p
POWER switch (11)  
q DISPLAY MODE button (23)  
w TA/NEWS/INFO button (26)  
e EON button (26)  
However,pressingMENU(lontheremotecontrol)overrides  
the selected function and causes Control  
%/ fi / @ / #  
r PTY SEARCH button (24)  
button to act like the % / fi / @ / # buttons on the ON  
SCREEN CONTROL section (l) of the remote control  
(though a lamp for the selected function remains lit).  
To return the Control % / fi / @ / # buttons to their usual  
behavior under the selected function, press the function  
button again.  
t SURROUND ADJUST button and lamp (30, 32)  
y SETTING button and lamp (15 to 18)  
u VIDEO 2 input jacks (10)  
i Control % / fi / @ / # buttons  
o SPEAKERS 1/2 buttons (13)  
; TUNER button and lamp (20)  
a PHONES jack (14)  
s MEMORY button for presetting channels (20)  
d SEA ADJUST button and lamp (28)  
This mark indicates that you can also use the menu function to do the  
same operations.  
Actual operations using the menu function are explained on the pages  
indicated next to the marks.  
MENU  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
Inside panel  
Outside panel  
f
z
SEND/LEARN  
ERROR  
SEND/LEARN  
ERROR  
m
LEARN  
CANCEL  
VCR  
EXT.1  
EXT.2  
TUNER  
TV  
VCR  
AUDIO  
SLEEP  
x
c
SEQUENTIAL PROGRAM KEY  
TV  
CD DISC  
g
h
A
B
C
ONE TOUCH  
OPERATION  
SOUND  
CD  
TAPE  
CONTROL  
,
.
SOURCE SELECT  
CONTROL  
VIDEO1  
VIDEO2  
VCR  
DELAY  
+
–
CENTER  
1
5
9
2
3
4
SURROUND  
MODE  
TV SOUND  
TAPE  
FM  
CD  
AM  
+
–
REAR  
TEST  
v
6
7/P  
8
j
k
FM  
SEA  
MODE  
PHONO  
MODE/MUTE  
10  
0
+10  
PRESET  
CHANNEL  
TV  
VOLUME  
MENU  
MENU  
EXIT  
PTY SELECT  
PTY SELECT  
PTY SEARCH  
DISPLAY MODE  
–
+
TV/VIDEO  
TAPE  
l
/
MUTE  
b
n
ON SCREEN CONTROL  
L
BALANCE  
R
VOLUME  
L
BALANCE  
R
VOLUME  
RM-SR730RU REMOTE CONTROL  
RM-SR730RU REMOTE CONTROL  
How to open the outside panel  
Remote Control  
Outside panel  
f SEND/LEARN indicator (45 to 49)  
g SEQUENTIAL PROGRAM KEYs (45 to 49)  
h ONE TOUCH OPERATION button (19)  
j SURROUND MODE button (30, 34, 36)  
k SEA MODE button (27)  
SEND/LEARN  
l Menu function buttons (ON SCREEN CONTROL section) (37)  
/ BALANCE L/R (+/–) buttons (15)  
ERROR  
5
3
9
6
0
z ERROR indicator (45 to 49)  
10  
4
x
(Standby/On) buttons (POWER section) (12, 44, 47, 48)  
+1
L
BALANCE  
c SLEEP button (16)  
R
VOLUME  
v Source select buttons (SOURCE SELECT section) (13)  
b MUTE button (14)  
RM-SR992U REMOTE CONTROL  
n VOLUME +/– buttons (13)  
Inside panel  
m Learning function buttons (45 to 49)  
, Remote mode section (42 to 49)  
. 10 keys (21)  
IMPORTANT  
Sound Adjustment buttons (30, 34)  
Component operating buttons (42 to 44)  
RDS operating buttons (25, 42)  
About the % / fi / @ / # buttons on the ON SCREEN  
CONTROL section (l) of the remote control:  
Ifyoupressthesebuttons,themenufunctionstartsoperating.  
So, makesureyouareshowingtheon-screendisplayonthe  
TV before pressing these buttons.  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the FM and AM (MW/LW) Antennas  
FM Antenna Connections  
Using the Supplied FM Antenna  
A
B
A
B
TheFMantennaprovidedcanbeconnectedtotheFM  
75-ohm COAXIAL terminal as temporary measure.  
UsingtheStandardTypeConnector(NotSupplied)  
Astandardtypeconnector(IECorDIN45325)should  
be connected to the FM 75-ohm COAXIAL terminal.  
FM 75  
ANTENNA  
FM 75  
ANTENNA  
AXIAL  
CO  
AXIAL  
CO  
GND  
GND  
T  
T  
AM  
LOOP  
AM  
LOOP  
Note:Makesuretheantennaconductorsdonottouchany  
other terminals, connecting cords or power cord.  
This could cause poor reception.  
Extend the FM wire antenna horizontally.  
ATENNA  
FM Antenna  
FM 75  
COAXIAL  
If reception is poor, connect the outside  
antenna.  
GND  
Before attaching a 75-ohm coaxial cable  
(the kind with a round wire going to the  
outdoor FM antenna), disconnect the  
supplied FM antenna.  
AM  
LOOP  
Outside FM Antenna Wire  
AM  
EXT  
AM (MW/LW) Antenna Connections  
ANTENNA  
FM 75  
COAXIAL  
Turn the loop until you have the best reception.  
AM (MW/LW) Loop Antenna  
GND  
AM  
LOOP  
AM  
EXT  
Snap the tabs on the loop into the slots of the  
base to assemble the AM (MW/LW) loop.  
3
1
2
If reception is poor, connect an outdoor single vinyl-  
covered wire to the AM EXT terminal. (Keep the AM  
(MW/LW) loop antenna connected.)  
AM (MW/LW) Wire Antenna  
Note:  
Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could  
cause poor reception.  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Speakers  
You can connect the following speakers:  
• Two pairs of front speakers to produce normal stereo sound.  
• One pair of rear speakers to enjoy the surround effect.  
• One center speaker to produce more effective surround effect (to emphasize human voices).  
• One subwoofer to enhance the bass.  
For each speaker (except for subwoofer), connect the black (–) and red (+) terminals on the rear panel to the  
black (–) and red (+) terminals marked on the speakers. For connecting a subwoofer, see page 7.  
CAUTION:  
When connecting speakers, use speakers with the SPEAKER IMPEDANCE indicated by the  
speaker terminals.  
Connecting the front speakers  
Cut, twist and remove the insulation at the end of each speaker signal cable first, and then, connect the front  
speakers to the FRONT SPEAKERS terminals by using the cables.  
You can connect two pairs of front speakers (one pair to the FRONT SPEAKERS 1 terminals, and another  
pair to the FRONT SPEAKERS 2 terminals).  
FRONT SPEAKERS  
RIGHT  
LEFT  
1
2
1
2
–
–
+
+
Left  
Speaker  
Right  
Speaker  
RIGHT  
LEFT  
2
Insert the speaker  
signal cable.  
3
Turn the knob  
clockwise.  
1
Turn the knob  
counterclockwise.  
1
1
1
RIGHT  
RIGHT  
RIGHT  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the rear and center speakers  
Cut, twist and remove the insulation at the end of each speaker signal cable first, and then, connect rear  
speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals by  
using the cables.  
1
Open the terminal and  
then insert the speaker  
signal cable.  
CENTER  
SPEAKER  
REAR  
SPEAKERS  
RIGHT LEFT  
Center Speaker  
Right Rear Speaker  
2
Close the terminal.  
Left Rear Speaker  
Notes:  
• You can register the center speaker size after you finish its connection. If you register it, you do not have  
to set the center speaker mode when setting the surround mode.  
(If you do not use a center speaker, register that information.) See page 17.  
• When you connect rear speakers, make sure that both left and right speakers are connected; otherwise, no  
sound will come out of the rear speakers.  
Connecting the subwoofer speaker  
You can enhance the bass by connecting a subwoofer.  
ConnecttheinputjackofapoweredsubwoofertotheSUBWOOFEROUTjackontherearpanel,usingacable  
with RCA pin plugs.  
SUBWOOFER  
OUT  
Powered subwoofer  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About the speaker impedance of the speakers  
CAUTION:  
When connecting speakers, use speakers with the SPEAKER IMPEDANCE indicated by the  
speaker terminals.  
Notes:  
• The required speaker impedance of the front speakers does not differ depending on whether both the  
FRONT SPEAKERS 1 and FRONT SPEAKERS 2 terminals are used or only one of them is used.  
• The required speaker impedance of the front speakers differs depending on whether or not a center and/  
or rear speakers are connected at the same time. Since there are four possible speaker connections with  
the receiver, check which one fits your case and use the speaker with the impedance described below.  
CASE 1 When you connect only front speakers  
CASE 2 When you connect front speakers and a center  
speaker  
Front  
Front  
Front  
Front  
Speaker  
Speaker  
Speaker  
Speaker  
Center Speaker  
Use front speakers with 4 — 16 ohm impedance.  
Use the following speakers;  
• Front speakers: 8 — 16 ohm impedance  
• Center speaker: 8 — 16 ohm impedance  
CASE 3 When you connect front and rear speakers  
CASE 4 When you connect front and rear speakers as  
well as a center speaker  
Front  
Speaker  
Front  
Speaker  
Front  
Speaker  
Front  
Speaker  
Center Speaker  
Rear  
Speaker  
Rear  
Speaker  
Rear  
Speaker  
Rear  
Speaker  
Use the following speakers;  
Use the following speakers;  
• Front speakers: 8 — 16 ohm impedance  
• Rear speakers: 8 — 16 ohm impedance  
• Front speakers: 8 — 16 ohm impedance  
• Rear speakers: 8 — 16 ohm impedance  
• Center speaker: 8 — 16 ohm impedance  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Audio/Video Components  
You can connect the following audio/video components to this receiver using cables with RCA pin plugs (not  
supplied). Refer also to the manuals supplied with your components. If you want to connect a component not  
listed in the table below, refer to the manual supplied with it.  
Audio Components  
Video Components  
•
•
•
Turntable  
•
•
•
•
TV  
CD player  
Cassette deck  
VCR(s)  
Video disc player  
Video camera  
Notes:  
• If you connect a sound-enhancing device such as a graphic equalizer between the source components and  
this receiver, the sound output through this receiver may be distorted.  
• Anyturntablesincorporatingasmall-outputcartridgesuchasanMC(moving-coiltype)mustbeconnected  
to this receiver through a commercial head amplifier or step-up transformer. Direct connection may result  
in insufficient volume.  
Audio component connections  
Ifagroundwireisprovidedforyourturntable,  
connect the cable to the screw marked GND  
on the rear panel.  
To audio output  
AUDIO  
GND  
RIGHT  
LEFT  
Turntable  
PHONO  
CD  
To audio output  
VIDEO  
CD player  
OUT  
(REC)  
OUT  
(REC)  
VCR  
VCR  
IN  
(PLAY)  
IN  
(PLAY)  
VIDEO 1  
VIDEO 1  
TV  
SOUND  
MONITOR  
OUT  
OUT  
(REC)  
To audio input  
TAPE  
IN  
(PLAY)  
To audio output  
Cassette deck  
If your audio components have a COMPU LINK-3 terminal  
The COMPU LINK remote control system allows you to control other JVC audio components from the  
receiver or vice versa.  
Connect your audio components and the receiver with the cable (monaural mini-plug supplied with those  
components) as well as the connection above.  
For detailed information about the connection and the COMPU LINK-3 remote control system, see page 41.  
Note:  
The COMPU LINK-3 remote control system is the upgraded version of the COMPU LINK-1 and COMPU  
LINK-2. Even if your component has the COMPU LINK-1 or COMPU LINK-2 jacks, you can still connect  
it in the COMPU LINK-3 remote control system, but some functions may not work correctly.  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video component connections  
AUDIO  
RIGHT LEFT  
GND  
PHONO  
CD  
To video input  
To audio input  
VIDEO  
VHS  
OUT  
(REC)  
OUT  
(REC)  
To audio output  
To video output  
VCR  
VCR  
VCR  
IN  
(PLAY)  
IN  
(PLAY)  
VIDEO 1  
To audio output  
To video output  
VIDEO 1  
To video input  
TV  
SOUND  
MONITOR  
OUT  
TV  
To audio output  
Video disc player  
OUT  
(REC)  
TAPE  
IN  
(PLAY)  
You can use the VIDEO 2 input jacks on the front panel. These jacks are convenient for connecting and  
disconnecting the component frequently.  
VIDEO 2  
Video camera  
VIDEO  
L
AUDIO  
R
MASTER VOLUME  
RX-730R AUDIO/VIDEO CONTROL RECEIVER  
ONE TOUCH  
VIDEO1  
VIDEO2  
VCR  
TV SOUND  
FM  
AM  
CD  
AM  
PHONO  
OPERATION  
–
+
SOURCE  
SURROUND MODE  
SEA MODE  
SURROUND  
ADJUST  
SEA  
MEMORY  
MEMORY  
ADJUST  
SETTING  
TUNER  
VIDEO  
2
SPEAKERS  
PHONES  
STANDBY  
VIDEO  
L
AUDIO  
R
1
2
To audio output  
To video output  
POWER  
DISPLAY  
MODE  
TA/NEWS/INFO  
EON  
PTY SEARCH  
_ON —OFF  
STANDBY/ON  
_ON —OFF  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Power Cord  
Before plugging the receiver into an AC outlet, make sure that all connections have been made.  
1. Plug the power cord into an AC outlet.  
POWER  
2. Press POWER to set it in the _ON position.  
The STANDBY lamp lights up. A small amount of power is always consumed.  
_ON OFF  
To shut off the power completely:  
Press POWER to set it in the —OFF position.  
Keep the power cord away from the connecting cables for the TV, VCR, and antenna. The power cord may  
cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since  
it is well-shielded against interference.  
The difference between the POWER switch and the STANDBY/ON  
button  
• The POWER switch is the mains supply switch, allowing the receiver to connect to the mains supply.  
To shut off the power completely, press the POWER switch to set it in the —OFF position.  
• The STANDBY/ON  
button is a functional on/off (standby) switch, and does not disconnect the  
receiver from the mains supply. A small amount of power is consumed even in standby mode for the  
receiver to accept signals from the remote control.  
Note:  
A preset settings such as preset channels and sound adjustments may be erased in the following cases:  
• When you press POWER to set it in the —OFF position.  
• When you unplug the power cord.  
• When a power failure occurs.  
CAUTIONS:  
• Do not touch the power cord with wet hands.  
• Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp  
the plug so as not to damage the cord.  
Putting Batteries in the Remote Control  
Before using the remote control, put two supplied batteries first. When using the remote control, aim the  
remote control directly at the remote sensor on the receiver.  
1. On the back of the remote control, remove the cover as illustrated.  
2. Insert batteries. Make sure to observe the proper polarity: (+) to (+) and (–) to (–).  
3. Replace the cover in.  
R03 (UM-4)/AAA (24F)  
If the range or effectiveness of the remote control decreases, replace the batteries. Use two R03 (UM-4)/AAA  
(24F) type dry-cell batteries.  
Note:  
When you replacing the batteries, finish it without delay; otherwise, the control signals you have stored are  
all erased. (See pages 45 and 47.)  
CAUTIONS:  
Follow these precautions to avoid leaking or cracking cells:  
• Place batteries in the remote control so they match the polarity indicated: (+) to (+) and (–)  
to (–).  
• Use the correct type of batteries. Batteries that look similar may differ in voltage.  
• Always replace both batteries at the same time.  
• Do not expose batteries to heat or flame.  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
The following operations are commonly used when you play any sound source.  
Turning the Power On and Off  
On the front panel:  
STANDBY  
To turn on the power, press STANDBY/ON  
.
The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the  
display.  
STAN
Current source  
name appears  
Volume level is also  
shown here  
whenever the power  
is on.  
100  
1k  
10k  
VOLUME  
STANDBY  
To turn off the power (into standby mode), press STANDBY/ON  
again.  
STAN
The STANDBY lamp lights up.  
Front panel  
From the remote control:  
To turn on the power, press AUDIO  
.
AUDIO  
The STANDBY lamp goes off. The name of the current source appears on the display.  
To turn off the power (into standby mode), press AUDIO  
again.  
The STANDBY lamp lights up.  
Remote: Outside  
Note:  
Pressing STANDBY/ON  
or AUDIO  
again turns off the power (into standby mode) and lights the  
STANDBY lamp. A small amount of power is consumed in standby mode. To turn the power off completely,  
press  
POWER to set it in the —OFF position on the front panel.  
See also  
page 37.  
MENU  
Selecting the Source to Play  
You need to select the source before you start playing any source.  
On the front panel:  
1. Press SOURCE so that the Control % / fi buttons work for selecting the source.  
SOURCE  
2. Press Control % / fi until the source name you want appears on the display.  
The selected source lamp also lights up.  
MUTE AUTO TUNED STEREO  
TA NEWS INFO  
SLEEP  
EON  
FM  
AM  
Selected source  
name appears  
MHz  
kHz  
CH–  
SURROUND PRO LOGIC 3CH LOGIC HALL  
SEA  
LOUDNESS  
100  
1k  
10k  
VISUAL CONFIRMATION  
VOLUME  
Front panel  
Page 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
From the remote control:  
Press one of the buttons on the SOURCE SELECT section.  
VIDEO1  
VIDEO2  
VCR  
TV SOUND  
FM*  
AM*  
TAPE*  
CD*  
Play back a video source on the video component connected to the VIDEO1 jacks.  
Play back a video source on the video component connected to the VIDEO2 jacks.  
Play back a video source on the video component connected to the VCR jacks.  
Listen to TV sounds.  
Listen to FM broadcasts.  
Listen to AM (MW/LW) broadcasts.  
Listen to a cassette tape.  
Listen to a CD.  
SOURCE SELECT  
VIDEO 1  
VIDEO 2  
VCR  
TV SOUND  
TAPE  
FM  
CD  
AM  
PHONO  
PHONO*  
Listen to a record.  
Note:  
When you press one of the buttons on the SOURCE SELECT section marked above with an asterisk (*), the  
receiver automatically turns on.  
Remote: Outside  
Adjusting the Volume  
When you change the volume level, the volume level is shown on the display.  
MASTER VOLUME  
On the front panel:  
–
+
To increase the volume, turn MASTER VOLUME clockwise.  
To decrease the volume, turn MASTER VOLUME counterclockwise.  
When you turn MASTER VOLUME rapidly, the volume level also changes rapidly.  
When you turn MASTER VOLUME slowly, the volume level also changes slowly.  
Front panel  
From the remote control:  
To increase the volume, press VOLUME +.  
To decrease the volume, press VOLUME –.  
VOLUME  
CAUTION:  
Always set the volume level to the minimum before starting any source. If the volume level is  
left turned up, the sudden blast of sound energy can permanently damage your hearing and/  
or ruin your speakers.  
Remote: Outside  
Selecting the Front Speakers  
On the front panel only:  
When you have connected two pairs of the front speakers, you can select which to use. Pressing SPEAKERS  
SPEAKERS  
1
2
1 or SPEAKERS 2 to set it in the _ON position activates the respective pair of the speakers.  
To use the speakers connected to the FRONT SPEAKERS 1 terminals, press SPEAKERS 1 to set it in  
the _ON position, and press SPEAKERS 2 to set it in the —OFF position.  
_ON —OFF  
To use the speakers connected to the FRONT SPEAKERS 2 terminals, press SPEAKERS 2 to set it in  
the _ON position, and press SPEAKERS 1 to set it in the —OFF position.  
To use both pairs of the speakers, press both SPEAKERS 1 and 2 to set them in the _ON position.  
To use neither pair of the speakers, press both SPEAKERS 1 and 2 to set them in the —OFF position.  
Front panel  
Note:  
When only one pair of the speakers is connected to either the FRONT SPEAKERS 1 or 2 terminals, do not  
press both SPEAKERS 1 and 2 to set them in the _ON position. If you do, no sound comes out of the front  
speakers.  
Page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening with Headphones  
A standard pair of headphones can be connected to the PHONES jack on the front panel.  
To listen with only headphones, press both SPEAKERS 1 and 2 to set them in the —OFF position.  
No sound comes out of the front speakers.  
CAUTION:  
Be sure to turn down the volume before connecting or putting on headphones, as high volume  
can damage both the headphones and your hearing.  
Muting the Sound  
From the remote control only:  
MUTE  
To mute the sound through all the speakers and headphones connected, press MUTE so that  
“MUTE” appears on the display and the volume turns off.  
To cancel the mute, press MUTE again so that “OFF” appears on the display.  
Turning MASTER VOLUME or pressing VOLUME +/– also restores the sound at the previous volume level.  
Remote: Outside  
Recording a Source  
You can record any source playing through the receiver to the cassette deck connected to the TAPE jacks and  
the VCR connected to the VCR jacks at the same time.  
Whilerecording,youcanlistentotheselectedsoundsourceatwhateversoundlevelyoulike,withoutaffecting  
the sound levels of the recording.  
Note:  
The output volume level, SEA, and surround modes cannot affect the recording.  
Page 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Settings  
Some of the following settings are required after connecting and positioning your speakers in your listening  
room, while others will make operations easier.  
See also  
page 37.  
MENU  
Adjusting the Front Speaker Output Balance  
If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output  
balance.  
On the front panel:  
SETTING  
1. Press SETTING so that the Control % / fi / @ / # buttons work for adjusting the balance.  
The lamp next to the button lights up.  
2. Press Control % / fi until “BALANCE” appears on the display.  
3. Press Control @ / # to adjust the balance.  
• Pressing Control @ decreases the right channel output.  
• Pressing Control # decreases the left channel output.  
From the remote control:  
Press BALANCE L/R (–/+).  
• Pressing BALANCE L (–) decreases the right channel output.  
• Pressing BALANCE R (+) decreases the left channel output.  
L
BALANCE  
R
Front panel  
See also  
page 38.  
MENU  
Listening at Low Volume (Loudness)  
Human ears are not sensitive to bass at low volume. To compensate for this, the loudness function  
automatically boosts the bass level as you lower the volume.  
Note:  
The loudness function affects the front speaker sounds only.  
On the front panel only:  
1. Press SETTING so that the Control % / fi / @ / # buttons work for setting the loudness  
SETTING  
function.  
The lamp next to the button lights up.  
2. Press Control % / fi until “LOUDNESS” appears on the display.  
3. Press Control @ / # to set the loudness function to “ON” or “OFF.”  
• Select “ON ” to activate the loudness function.  
The LOUDNESS indicator lights up on the display.  
• Select “OFF” to cancel it.  
The indicator goes off.  
Front panel  
Page 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
See also  
page 38.  
MENU  
Using the Sleep Timer  
Using the Sleep Timer, you can fall asleep to music and know the receiver will turn off by itself rather than  
play all night.  
SETTING  
On the front panel:  
1. Press SETTING so that the Control % / fi / @ / # buttons work for setting the Sleep Timer.  
The lamp next to the button lights up.  
2. Press Control % / fi until “<SLEEP>” appears on the display.  
3. Press Control @ / # to set the shut-off time.  
Each time you press the button, the shut-off time on the display changes as follows:  
The SLEEP indicator lights up on the display.  
10  
20  
30  
40  
50  
60  
70  
80  
(Canceled)  
0
When the shut-off time comes  
The receiver turns off (into standby mode) automatically.  
To check or change the time remaining until the shut-off time  
1. Press SETTING, if necessary, so that the Control % / fi / @ / # buttons work for setting the Sleep  
Timer.  
Front panel  
2. Press Control % / fi, if necessary, until “<SLEEP>” appears on the display.  
3. Press Control @ / # once.  
The remaining time until the shut-off time appears in minutes.  
• To change the shut-off time, press Control @ / # repeatedly.  
To cancel the Sleep Timer  
Press Control @ / # repeatedly in step 3 above until “0” appears on the display. (The SLEEP indicator goes  
off.) Turning off the power (into standby mode) also cancels the Sleep Timer.  
From the remote control:  
Press SLEEP repeatedly.  
SLEEP  
The SLEEP indicator lights up and the shut-off time appears on the display.  
Each time you press the button, the shut-off time on the display changes as follows:  
10  
20  
30  
40  
50  
60  
70  
80  
Remote: Outside  
(Canceled)  
0
To check or change the time remaining until the shut-off time  
Press SLEEP once. The remaining time until the shut-off time appears in minutes.  
• To change the shut-off time, press SLEEP repeatedly.  
To cancel the Sleep Timer  
Press SLEEP repeatedly until “0” appears on the display. (The SLEEP indicator goes off.)  
Turning off the power (into standby mode) also cancels the Sleep Timer.  
Page 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
See also  
page 38.  
MENU  
Selecting the Center Speaker Size  
You can register the information on the center speaker after all connections are completed.  
If you do this registration first, you do not have to adjust the center speaker mode when you want to activate  
the Dolby Surround. However, to register the information, first you have to set the surround mode either to  
“PROLOGIC” or “3CHLOGIC.” (You cannot select the center speaker size when the surround mode is  
“SURR OFF” or “HALL.”)  
On the front panel only:  
SURROUND MODE  
1. Press SURROUND MODE so that the Control % / fi buttons work for selecting the surround  
mode.  
The lamp next to the button lights up.  
2. Press Control % / fi until “PROLOGIC” or “3CHLOGIC” whichever you want appears on the  
display.  
The PRO LOGIC or 3CH LOGIC indicator (as well as the SURROUND indicator) also lights up.  
3. Press SETTING so that the Control % / fi / @ / # buttons work for selecting the center speaker  
size.  
The lamp next to the button lights up.  
SETTING  
4. Press Control % / fi until “CNTR SPK” (Center Speaker) appears on the display.  
5. Press Control @ / # to select the appropriate item about your center speaker.  
Each time you press the button, the display changes to show the following:  
LARGE  
SMALL  
NO  
LARGE:  
Select this mode when the size of the center speaker is the same as that of the  
front speakers.  
SMALL:  
NO:  
Select this mode when the size of the center speaker is smaller than that of the  
front speakers.  
Select this mode when you do not use a center speaker.  
(You cannot select this mode when “3CHLOGIC” is selected for the surround  
mode.)  
Note:  
This center speaker size setting is so related to the center mode setting for the Dolby Surround mode that  
changing this setting affects and changes the center mode to a relevant mode, and vice versa.  
For example;  
Front panel  
• If you select “LARGE,” the center mode is automatically set to “WIDE,” and vice versa.  
• If you select “SMALL,” the center mode is automatically set to “NORMAL,” and vice versa.  
• If you select “NO,” the center mode is automatically set to “PHANTOM” for Pro Logic and vice versa.  
Page 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
See also  
page 38.  
MENU  
Using Visual Confirmation  
When you operate the receiver, you can see what you are doing, by showing it on the TV screen.  
To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 10),  
and set the TV’s input mode to the proper position to which the receiver is connected.  
When the TV’s input mode is for TV, you cannot see the on-screen display.  
On the front panel only:  
1. Press SETTING so that the Control % / fi / @ / # buttons work for setting Visual  
Confirmation.  
SETTING  
The lamp next to the button lights up.  
2. Press Control % / fi until “VCONFIRM” appears on the display.  
3. Press Control @ / # to set Visual Confirmation to “ON” or “OFF.”  
• Select “ON ” to activate Visual Confirmation.  
The VISUAL CONFIRMATION indicator lights up on the display.  
• Select “OFF” to cancel it.  
The indicator goes off.  
Front panel  
EXAMPLES:  
When changing the source:  
The SOURCE menu appears on the TV screen for  
about 5 seconds.  
When adjusting the Pro Logic settings:  
The PRO LOGIC adjustment menu appears on the  
TV screen for about 5 seconds.  
When adjusting the center speaker size:  
The SETTING menu appears on the TV screen for  
about 5 seconds.  
Page 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
One Touch Operation  
This receiver can memorize the optimum sound settings for each playing source.  
About the One Touch Operation  
JVC’s One Touch Operation function is used to assign and store different sound settings for each different  
playingsource. Byusingthisfunction, youdon’thavetochangethesettingseverytimeyouchangethesource.  
The stored settings for the newly selected source are automatically recalled.  
The following can be stored for each source:  
• Volume level (see page 13)  
• Balance (see page 15)  
• Loudness (see page 15)  
• SEA modes (see page 27)  
• Surround mode settings (see page 29)  
Note:  
If the source is FM or AM (MW/LW), the One Touch Operation function works only when the preset channels  
from 1 — 20 are tuned in. You can assign a different setting for each preset channel.  
Using the One Touch Operation  
To store the sound settings  
ONE TOUCH  
OPERATION  
1. Press ONE TOUCH OPERATION.  
The ONE TOUCH OPERATION lamp lights up, then the previously memorized settings are recalled  
and appear on the display in turn.  
2. Adjust the sound using the functions listed above.  
The newly adjusted settings are memorized.  
Front panel  
To recall the sound settings  
ONE TOUCH  
OPERATION  
With the ONE TOUCH OPERATION lamp lit, the settings for the currently selected source is recalled, and  
appears on the display when the source is selected.  
To cancel the One Touch Operation function  
Press ONE TOUCH OPERATION so that the lamp goes off.  
(Even though the One Touch Operation function is canceled, the recalled sound effects remain active.)  
Remote: Outside  
Page 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Receiving Radio Broadcasts  
You can browse through all the stations or use the preset function to go immediately to a particular station.  
See also  
page 39.  
MENU  
Tuning in Stations Manually  
On the front panel only:  
TUNER  
MEMORY  
1. Press TUNER so that the Control % / fi / @ / # buttons work for tuner settings.  
The lamp next to the button lights up.  
2. Press Control % / fi until “<FM AM>” appears on the display.  
3. Press Control @ / # to select the band.  
Each time you press the button, the band alternates between FM and AM (MW/LW).  
4. Press Control % / fi until “–TUNING+” appears on the display.  
5. Press Control @ / # until you find the frequency you want.  
• Pressing Control @ decreases the frequency.  
• Pressing Control # increases the frequency.  
Notes:  
• When you hold down Control@ /# in step 5, the frequency keeps changing until you press the button again  
or a station is tuned in.  
• When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display.  
When an FM stereo program is received, the STEREO indicator also lights up.  
Front panel  
See also  
page 39.  
MENU  
Using Preset Tuning  
Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 40  
stations at random.  
Storing the preset stations  
On the front panel only:  
1. Tune in the station you want to preset (see above).  
If you want to store the FM reception mode for this station, select the FM reception mode you want.  
See page 21 for details.  
TUNER  
MEMORY  
2. Press MEMORY (next to the TUNER button).  
“CH-” appears and the channel number position starts flashing on the display for about 5 seconds.  
3. Press Control % / fi to select a channel number while the channel number position is flashing.  
• Pressing Control % increases the number.  
• Pressing Control fi decreases the number.  
Note:  
You can use the 10 keys on the remote control to select the preset number. When using the 10 keys, be sure  
that they are activated for tuner, not for the CD and others. (See page 42.)  
4. Press MEMORY (next to the TUNER button) again while the selected channel number is  
flashing on the display.  
TUNER  
MEMORY  
The selected channel number stops flashing.  
The station is assigned to the selected channel number.  
5. Repeat steps 1 to 4 until you store all the stations you want.  
Front panel  
To cancel a stored preset station  
Storing a new station on a used number erases the previously stored one.  
Continued to the next page  
Page 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION:  
The preset channels may be erased in the following cases:  
• When you press POWER to set it in the — OFF position.  
• When you unplug the power cord.  
• When a power failure occurs.  
Tuning in a preset station  
On the front panel:  
1. Press TUNER so that the Control % / fi / @ / # buttons work for tuner settings.  
TUNER  
MEMORY  
The lamp next to the button lights up.  
2. Press Control % / fi until “–PRESET+” appears on the display.  
3. Press Control @ / # to select a preset channel.  
Each time you press the button, the preset channels changes.  
• Pressing Control @ changes preset channels in decreasing order.  
• Pressing Control # changes preset channels in increasing order.  
From the remote control:  
1. Press FM or AM.  
The last received station of the selected band is tuned in.  
2. Open the outside panel of the remote control and press PRESET CHANNEL +/–.  
To select a preset channel number directly, press 10 keys on the inside panel.  
• For channel number 5, press 5.  
• For channel number 15, press +10 then 5.  
• For channel number 20, press +10 then 10.  
• For channel number 30, press +10, +10, then 10.  
Front panel  
PRESET  
CHANNEL  
FM  
AM  
Note:  
When you use the 10 keys on the remote control, be sure that they are activated for tuner, not for the CD  
and others. (See page 42.)  
Remote:  
Outside  
Remote:  
Inside  
See also  
page 39.  
MENU  
Selecting the FM Reception Mode  
You can change the FM reception mode while listening an FM broadcast.  
You can also store the FM reception mode for each preset station. (See page 20.)  
TUNER  
MEMORY  
On the front panel:  
1. Press TUNER so that the Control % / fi / @ / # buttons work for tuner settings.  
The lamp next to the button lights up.  
2. Press Control % / fi until “FM MODE” appears on the display.  
3. Press Control @ / # to select either “AUTO” or “MONO.”  
• Normally select “AUTO.”  
• When an FM stereo broadcast is hard to receive or noisy, select “MONO.”  
AUTO:  
When a program is broadcast in stereo, you will hear stereo sound; when in  
monaural, you will hear monaural sounds. This mode is also useful to suppress  
static noise between stations.  
The MUTE AUTO indicator lights up on the display.  
MONO:  
Reception will be improved although you will lose the stereo effect. In this  
mode, you will hear noise while tuning into the stations.  
Front panel  
The MUTE AUTO indicator goes off on the display.  
FM  
From the remote control:  
Press FM MODE/MUTE.  
MODE/MUTE  
0
Each time you press the button, “AUTO” and “MONO” alternately appears on the display.  
Note:  
Remote: Inside  
When you use the FM MODE/MUTE button, be sure that 10 keys are activated for tuner, not for the CD and  
others. (See page 42.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Page 21  
See also  
page 39.  
MENU  
Assigning Names to Preset Stations  
You can assign a name of up to five characters to each preset station (from preset channel number 1 to 20).  
When a preset station is tuned in, its assigned name will appear on the display.  
On the front panel only:  
1. Tune in a preset station (preset channel number 1 to 20).  
See page 21 for details.  
2. Press MEMORY (next to the TUNER button).  
The preset channel number starts flashing.  
CH–  
TUNER  
MEMORY  
Note:  
If you press Control % / fi while the preset channel  
numberisflashing,youcanchangethepresetchannel  
100  
1k  
10k  
VISUAL CONFIRMATION  
number.  
3. Press Control # (or @) until the first character  
position starts flashing.  
CH–  
100  
1k  
10k  
VISUAL CONFIRMATION  
4. Press Control % / fi to select a character.  
You can use characters listed below.  
CH–  
100  
1k  
10k  
VISUAL CONFIRMATION  
5. When a character you want appears, press  
Control # (or @).  
The next (or previous) character position starts  
flashing.  
CH–  
100  
1k  
10k  
VISUAL CONFIRMATION  
6. Repeat steps 4 and 5 to enter up to five characters.  
7. Press MEMORY (next to the TUNER button) again while the last selected character is flashing,  
after you have assigned a name.  
TUNER  
MEMORY  
To erase the input characters  
Front panel  
Insert blanks using the same procedure described above.  
Available characters  
Blank  
A
Q
6
B
R
7
C
S
8
D
T
9
E
U
F
V
G
H
X
I
J
K
0
L
1
M
2
N
3
O
4
P
5
W
Y
Z
Page 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
See also  
page 39.  
MENU  
Using the RDS (Radio Data System) to Receive FM Stations  
RDS allows FM stations to send an additional signal along with their regular program signals. For example,  
the stations send their station names, as well as information about what type of program they broadcast, such  
as sports or music, etc.  
When tuned to an FM station which provides the RDS service, the RDS indicator lights up on the display.  
With the receiver, you can receive the following types of RDS signals.  
PS (Program Service) :  
PTY (Program Type) :  
RT (Radio Text) :  
shows commonly known station names  
shows types of broadcast programs  
shows text messages the station sends  
About characters shown on the display  
When the display shows PS, PTY, or RT signals, the following characters are used.  
• The display cannot differentiate upper case and lower case letters and always uses upper case letters.  
• The display cannot show accented letters, “A”, for instance, may stand for accented “A’s” like “Å, Ä,  
Ã, Á, À, and Â.”  
A, Å, Ä,  
Ã, Á, À, Â  
B
K
U, Ü, Ú,  
Ù, Û  
V
0
1
2
<
>
=
*
+
-
L
M
W
C, C, C  
D, D  
N, Ñ  
X
3
\
'
,
E, Ë, É,  
È, Ê  
F
O, Ö, Õ, Ô,  
Ò, Ó, Ø  
P
Y
4
5
6
.
/
Z, Z, Z  
G
Q
–
–
H
R, R, R  
S, S, S  
T
7
8
9
I, Ï, Í, Ì, Î  
J
–
Note:  
RDS may not operate correctly if the station tuned is not transmitting data properly or if the signal strength  
is weak.  
See also  
page 39.  
MENU  
What Information Can RDS Signals Provide?  
You can see the RDS signals the station sends.  
To show the RDS signals  
DISPLAY MODE  
Press DISPLAY MODE while listening to an FM station.  
Each time you press the button, the display changes to show you the following information:  
PS  
PTY  
RT  
Frequency  
Front panel  
PS (Program Service):  
While searching, “PS” appears and then the station names will be displayed. “NO PS” appears if no  
signal is sent.  
PTY (Program Type):  
While searching, “PTY” appears and then the type of the broadcast program will be displayed. “NO  
PTY” appears if no signal is sent.  
RT (Radio Text):  
While searching, “RT” appears and then text messages the station sends will be displayed. “NO RT”  
appears if no signal is sent.  
Station Frequency:  
Station frequency (non-RDS service)  
Page 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When pressing DISPLAY MODE on the remote control:  
DISPLAY MODE  
TUNER  
Make sure that you have selected FM station using the remote control only.  
Ifnot, theDISPLAYMODEbuttondoesnotworkfortuneroperation. (PressingTUNER(ontheremotemode  
section of the inside panel) activates the remote control for tuner operation.)  
\
Notes:  
Remote: Inside  
• If searching finishes at once, “PS”, “PTY”, and “RT” will not appear on the display.  
• If you press DISPLAY MODE while listening to an AM (MW/LW) station, the display only shows station  
frequency.  
• RDS is not available for AM (MW/LW) broadcasts.  
See also  
page 39.  
MENU  
Searching for a Program by PTY Codes  
One of the advantages of the RDS service is that you can locate a particular kind of program from the preset  
channels by specifying the PTY codes.  
To search for a program using the PTY codes  
On the front panel:  
PTY SEARCH  
1. Press PTY SEARCH while listening to an FM station so that Control @ / # buttons work for  
selecting PTY code.  
“PTY” and “SELECT” alternate on the display.  
2. Press Control @ / # until the PTY code you want appears on the display.  
Each time you press the button, the display gives you the PTY codes described on page 25.  
3. Press PTY SEARCH again.  
While searching, “SEARCH” and the selected PTY code alternate on the display.  
The receiver searches 40 preset channels, stops when it finds the one you have selected, and tunes in  
that station.  
PTY SEARCH  
To continue searching after the first stop:  
PTY SEARCH  
Press PTY SEARCH again while the indications on the display are flashing.  
If no program is found, “NOTFOUND” appears on the display.  
To stop searching any time during the process:  
Front panel  
Press PTY SEARCH while searching.  
Page 24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
From the remote control:  
Before starting the procedure below, make sure you have selected FM station only using the remote control.  
If not, the following RDS operating buttons do not work for tuner operation. (Pressing TUNER (on the remote  
mode section of the inside panel) activates the remote control for tuner operation.)  
PTY SEARCH  
1. Press PTY SEARCH while listening to an FM station.  
“PTY” and “SELECT” alternate on the display.  
PTY SELECT  
PTY SELECT  
2. Press PTY SELECT +/– until the PTY code you want appears on the display.  
–
+
PTY SEARCH  
The display gives you the PTY codes described below.  
3. Press PTY SEARCH again.  
While searching, “SEARCH” and the selected PTY code alternate on the display.  
The receiver searches 40 preset channels, stops when it finds the one you have selected, and tunes in  
that station.  
PTY SEARCH  
To continue searching after the first stop:  
PTY SEARCH  
Press PTY SEARCH again while the indications on the display are flashing.  
If no program is found, “NOTFOUND” appears on the display.  
To stop searching any time during the process:  
Press PTY SEARCH while searching.  
Remote: Inside  
Descriptions of the PTY codes:  
NEWS  
NEWS:  
News  
AFFAIRS:  
INFO:  
SPORT:  
Topical programs expanding on the current news or affairs  
Programs on medical service, weather forecast, etc.  
Sports events  
ALARM  
AFFAIRS  
INFO  
EDUCATE: Educational programs  
DRAMA: Radio plays  
CULTURE: Programs on national or regional culture  
SCIENCE:  
VARIED:  
POP M:  
ROCK M:  
M.O.R. M:  
LIGHT M: Light music  
CLASSICS: Classics  
OTHER M  
CLASSICS  
LIGHT M  
M.O.R. M  
ROCK M  
POP M  
Programs on natural sciences and technology  
Other programs like comedies or ceremonies  
Pop music  
SPORT  
Rock music  
Middle-of-the-road music (usually called “easy listening”)  
EDUCATE  
DRAMA  
OTHER M: Other music  
ALARM:  
Emergency broadcast  
NONE:  
Undefined (this cannot be searched.)  
CULTURE  
SCIENCE  
When an emergency broadcast (ALARM signal) is sent from an FM station:  
The receiver automatically switches the source to FM and tunes in the station except in the following cases:  
• When you are listening to non-RDS stations (all AM (MW/LW) and some FM stations).  
• When the receiver is in standby mode.  
VARIED  
While receiving an emergency broadcast, “ALARM” appears on the display.  
Page 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
See also  
page 39.  
MENU  
Switching to a Broadcast Program of Your Choice Temporarily  
Another convenient RDS service is called “EON (Enhanced Other Network).”  
This allows the receiver to switch temporarily to a broadcast program of your choice (NEWS, TA, and/or  
INFO) from a different station except in the following cases:  
• When you are listening to a non-RDS stations (all AM (MW/LW) and some FM stations).  
• When the last received FM station is a non-RDS station.  
On the front panel only:  
EON  
1. Press EON so that the last selected program type appears on the display.  
The receiver enters EON standby mode.  
2. Press TA/NEWS/INFO until the program type you want appears on the display.  
TA/ NEWS /INFO  
Each time you press the button, the display changes to show the following.  
TA  
TA/INFO  
TA/NEWS  
NEWS/INFO  
INFO  
NEWS  
TA/NEWS/INFO  
Front panel  
TA:  
NEWS:  
INFO:  
Traffic Announcement in your area.  
News.  
Programs on medical service, weather forecast, etc.  
CASE 1 Ifthereisnostationbroadcastingtheprogram  
you have selected  
CASE 2 Ifthereisastationbroadcastingtheprogramyouhave  
selected  
Thereceivercontinuesplayingthecurrentsource.  
The receiver stops playing the current source, and tunes in  
the program. The indicator of received PTY code starts  
flashing.  
‘
When a station starts broadcasting the program  
you have selected, the receiver automatically  
switches to the station. The indicator of received  
PTY code starts flashing.  
‘
When the program is over, the receiver goes back to the  
previously selected source, but still remains in EON  
standby mode.  
‘
When the program is over, the receiver goes back  
tothepreviouslyselectedsource, butstillremains  
in EON standby mode.  
EON  
To stop listening to the program selected by EON:  
Press EON so that the program type (TA/NEWS/INFO) goes off from the display. The receiver enters EON  
off mode and goes back to the previously selected source.  
Each time you press EON, the EON mode alternates between standby mode and off mode.  
Notes:  
Front panel  
• InEONstandbymode, ifyouchangethesourcetoAM(MW/LW)orifyoucarryoutsynchronizedrecording  
(see page 41), EON standby mode is canceled temporarily. The receiver goes back to EON standby mode  
again when you have finished that operation.  
• While listening to a program tuned in by the EON function, you can only use STANDBY/ON  
, EON,  
and DISPLAY MODE on the front panel or AUDIO and DISPLAY MODE on the remote control.  
• When the receiver is turned off (into standby mode), the EON function is also turned off.  
CAUTION:  
When the source alternates intermittently between the station tuned in by the EON function and  
the currently selected source, press EON to cancel the EON function. This is not a malfunction  
of the receiver.  
Page 26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the SEA Modes  
The SEA (Sound Effect Amplifier) modes give you control of the way your music sounds.  
Note:  
The SEA modes cannot be used for recording.  
See also  
page 39.  
MENU  
Selecting Your Favorite SEA Mode  
On the front panel:  
SEA MODE  
1. Press SEA MODE so that the Control % / fi buttons work for selecting the SEA mode.  
The lamp next to the button lights up.  
2. Press Control % / fi until the mode you want appears on the display.  
Each time you press the button, the SEA mode changes as follows:  
ROCK  
MUSICAL  
MOVIE  
COUNTRY  
JAZZ  
SEA OFF  
USERMODE  
Note:  
When the SEA mode is turned on, the SEA indicator lights up on the display.  
ROCK:  
Gives a heavy sound. Both high and low frequencies are boosted.  
Front panel  
MUSICAL:  
MOVIE:  
Enhance the mid-frequency range, which the human voice is mostly made up of.  
Adds breadth to sounds so you feel like you are in a movie theater.  
COUNTRY:  
Enhances the high-frequency range so that instruments such the violin and banjo  
are emphasized.  
JAZZ:  
Gives a feeling of a live atmosphere. Good for acoustic music.  
Your original SEA adjustment (see page 28).  
No SEA mode is applied (see below).  
USERMODE:  
SEA OFF:  
To cancel the SEA mode, press Control % / fi until “SEA OFF” appears in step 2 above.  
The SEA indicator goes off from the display.  
From the remote control:  
Press SEA MODE repeatedly until the SEA mode you want appears on the display.  
SEA  
MODE  
Each time you press the button, the SEA mode changes as follows:  
ROCK  
MUSICAL  
MOVIE  
COUNTRY  
JAZZ  
SEA OFF  
USERMODE  
Remote: Outside  
Note:  
When the SEA mode is turned on, the SEA indicator lights up on the display.  
To cancel the SEA mode, press SEA MODE repeatedly until “SEA OFF” appears on the display.  
The SEA indicator goes off from the display.  
Page 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
See also  
page 39.  
MENU  
Creating Your Own SEA Mode  
You can adjust and store your own SEA adjustment into memory (USERMODE).  
On the front panel only:  
If you do not want to store your adjustment, but rather want to adjust the SEA temporarily, skip step 3 below.  
1. Press SEA ADJUST so that the Control % / fi / @ / # buttons work for the SEA adjustment.  
SEA  
ADJUST  
MEMORY  
The lamp next to the button lights up.  
2. Adjust the SEA frequency and its level.  
• Press Control @ / # to select the frequency range to adjust.  
• Press Control % / fi to adjust the level.  
100  
1k  
10k  
3. Press MEMORY (next to the SEA ADJUST button).  
Your adjustment is stored into USERMODE.  
SEA  
ADJUST  
MEMORY  
To recall your own SEA adjustment  
See page 27.  
To erase a stored adjustment  
Front panel  
Storing a new adjustment into USERMODE erases the previously stored one.  
Page 28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Surround Processor  
The built-in surround processor provides three types of surround programs — Dolby Pro Logic, Dolby 3-  
Channel Logic, and JVC’s Hall Surround.  
What is surround?  
The sound heard in a concert hall or a movie theater consists of direct sound and indirect sound: early  
reflectionsandreflectionsfrombehind.Thereflectedsoundsarealwaysdelayedbythedistancesoftheceiling  
and walls from the listener. These reflections are some of the most important elements of the acoustic  
surround.  
On JVC’s Hall Surround  
Inordertoreproduceamorerealisticsoundfieldinyourlistening  
roomwhileplayinganordinarystereosource,JVC’sHallSurround  
has been designed to give you clear vocals and to create the  
feeling of a concert hall. The sound is reproduced through the  
front speakers and rear speakers.  
Reflections  
from behind  
Early reflections  
On Dolby Surround  
Dolby Surround has been also developed to reproduce the  
important elements of the acoustic surround at home.  
To watch the soundtracks of video software bearing the mark  
DOLBY SURROUND  
* which includes the same encoded surround  
information as found in Dolby Stereo films, the receiver can  
provide you with 2 Dolby Surround programs (Dolby Pro Logic  
and Dolby 3ch Logic).  
Direct sound  
Dolby Pro Logic: Select this mode when the optional rear  
speakers are connected (as well as a center speaker).  
Dolby 3ch Logic: Select this mode when a center speaker is  
connected without rear speakers.  
Notes:  
* Manufactured under license from Dolby Laboratories Licensing  
Corporation. “Dolby,” the double-D symbol, and “Pro Logic” are  
trademarks of Dolby Laboratories Licensing Corporation.  
• The surround processor has no effect on monaural sources.  
• The surround processor cannot be used for recording.  
See also  
page 40.  
MENU  
Using JVC’s Hall Surround  
You need to connect one set of rear speakers to obtain the full effect.  
Once you have adjusted the Hall Surround, the receiver memorizes the settings.  
On the front panel:  
1. Press SURROUND MODE so that the Control % / fi buttons work for selecting the surround  
SURROUND MODE  
modes.  
The lamp next to the button lights up.  
2. Press Control % / fi until “HALL” appears on the display.  
The HALL and SURROUND indicators also light up on the display.  
Each time you press the button, the surround modes change as follows (the indicator of the selected  
surround mode also lights up on the display):  
PROLOGIC  
3CHLOGIC  
HALL  
SURR OFF  
(Surround Off)  
Front panel  
Page 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Press SURROUND ADJUST so that the Control  
settings.  
                                                                    
%
                                                                     
/
                                                                       
fi
                                                                       
/
                                                                          
@
                                                                          
/
                                                                             
#
                                                                             
buttons work for surround  
SURROUND  
ADJUST  
The lamp next to the button lights up.  
4. Press Control % / fi until “– REAR +” appears on the display.  
5. Press Control @ / # to adjust the rear speaker output level.  
• Pressing Control @ decreases the output level up to –10 dB.  
• Pressing Control # increases the output level up to +10 dB.  
6. Press Control % / fi until “–DELAY +” appears on the display.  
7. Press Control @ / # to adjust the delay time of the rear speaker output.  
Each time you press the button, the delay time changes as follows:  
DELAY 1  
DELAY 4  
DELAY 2  
DELAY 3  
Front panel  
DELAY 1  
DELAY 2  
Select this when the distance from you to your rear speakers is greater than that to the front  
speakers.  
Select this when the distance from you to your rear speakers is almost equal to that to the  
front speakers.  
DELAY 3  
DELAY 4  
Select this when the distance from you to your rear speakers is a little less than that to the  
front speakers.  
Select this when the distance from you to your rear speakers is much less than that to the  
front speakers.  
To cancel the Hall surround, press Control % / fi until “SURR OFF” appears in step 2.  
The HALL and SURROUND indicators go off.  
From the remote control:  
SURROUND  
MODE  
1. Press SURROUND MODE repeatedly until “HALL” appears on the display.  
The HALL and SURROUND indicators also light up on the display.  
Each time you press the button, the surround modes change as follows (the indicator of the selected  
surround mode also lights up on the display):  
Remote: Outside  
PROLOGIC  
3CHLOGIC  
HALL  
SOUND  
CONTROL  
SURR OFF  
(Surround Off)  
2. Open the outside panel and press SOUND CONTROL on the remote mode section.  
+
–
REAR  
3. Press REAR +/– to adjust the rear speaker output level.  
• Pressing REAR – decreases the output level up to –10 dB.  
• Pressing REAR + increases the output level up to +10 dB.  
7/P  
8
4. Press DELAY to adjust the delay time.  
Each time you press the button, the delay time changes as follows:  
DELAY  
2
DELAY 1  
DELAY 4  
DELAY 2  
DELAY 3  
To cancel the Hall Surround, press SURROUND MODE until “SURR OFF” appears on the display.  
The HALL and SURROUND indicators go off.  
Remote: Inside  
Page 30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker Arrangements for Dolby Surround  
The following illustrations show how to obtain the optimum sound environment for various Dolby Surround  
settings. Try to find the speaker direction and location to create the optimum sound field.  
CASE 1 When you have added a center speaker and rear speakers  
TV  
Front  
Front  
speaker  
speaker  
Center speaker  
In this case:  
1.Select “PROLOGIC.”  
2.Select “NORMAL” or “WIDE”  
for center mode.  
Rear  
Rear  
speaker  
speaker  
See pages 32 to 35 for more details.  
CASE 2 When you have added rear speakers (without a center speaker)  
TV  
Front  
Front  
speaker  
speaker  
In this case:  
1.Select “PROLOGIC.”  
2.Select “PHANTOM” for center  
mode.  
Rear  
Rear  
speaker  
speaker  
See pages 32 to 35 for more details.  
CASE 3 When you have added a center speaker (without rear speakers)  
TV  
Front  
Front  
speaker  
speaker  
Center speaker  
In this case:  
1.Select “3CHLOGIC.”  
2.Select “NORMAL” or “WIDE”  
for center mode.  
See pages 32 to 35 for more details.  
Page 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
See also  
page 40.  
MENU  
Preparing for Dolby Surround  
The receiver memorizes two sets of Dolby Surround adjustments; one for Pro Logic and the other for 3ch  
Logic.  
On the front panel:  
1. Press SURROUND MODE so that the Control % / fi buttons work for selecting the surround  
SURROUND MODE  
modes.  
The lamp next to the button lights up.  
2. Press Control % / fi until “PROLOGIC” or “3CHLOGIC” whichever you want appears on the  
display.  
The PRO LOGIC or 3CH LOGIC indicator (as well as the SURROUND indicator) also lights up.  
Each time you press the button, the surround modes change as follows (the indicator of the selected  
surround mode also lights up on the display):  
PROLOGIC  
3CHLOGIC  
HALL  
Front panel  
SURR OFF  
(Surround Off)  
PROLOGIC  
Select this mode to watch a video source with Dolby Surround when you have  
connected the rear speakers (and a center speaker).  
3CHLOGIC  
HALL  
Select this mode to watch a video source with Dolby Surround when you have  
connected a center speaker and no rear speakers.  
Thisis JVC’soriginal surround mode, and isdifferent from Dolby Surround. To use  
this, see page 29.  
SURR OFF  
No surround mode is applied.  
SURROUND  
ADJUST  
3. Press SURROUND ADJUST so that the Control % / fi / @ / # buttons work for adjusting the  
surround mode.  
The lamp next to the button lights up.  
4. Press Control % / fi until “CNT MODE” (Center Mode) appears on the display.  
5. Press Control @ / # to select the center mode.  
Each time you press the button, the center modes change as follows:  
WIDE  
NORMAL  
OFF  
PHANTOM  
WIDE  
Select this mode when the center speaker can reproduce the bass better than the  
front speakers. All signals of the center channel are output through the center  
speaker.  
NORMAL  
Select this mode when the center speaker cannot reproduce the bass better than  
the front speakers. The bass portions of the center channel signals are output  
through the front speakers.  
Front panel  
PHANTOM  
OFF  
Selectthismodewhenyoudonotuseacenterspeaker.Thecenterspeakerchannel  
signals are output through the front speakers.  
Select this mode to turn off the center speaker channel.  
Notes:  
• If you have already set the “center speaker size” following the procedure described on page 17, you do not  
have to select the center mode in this procedure.  
• When you have selected “3CHLOGIC,” you cannot select “PHANTOM.”  
Continued to the next page  
Page 32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Press Control  
                                            
%
                                            
/
                                               
fi
                                               
until “–DELAY +” appears on the display.  
7. Press Control @ / # to adjust the delay time of the rear speaker output.  
Each time you press the button, the delay time changes as follows:  
DELAY 1  
DELAY 4  
DELAY 2  
DELAY 3  
DELAY 1  
DELAY 2  
DELAY 3  
DELAY 4  
Select this when the distance from you to your rear speakers is greater than that  
to the front speakers.  
Select this when the distance from you to your rear speakers is almost equal to  
that to the front speakers.  
Select this when the distance from you to your rear speakers is a little less than  
that to the front speakers.  
Front panel  
Select this when the distance from you to your rear speakers is much less than  
that to the front speakers.  
Note:  
When you have selected “3CHLOGIC,” you cannot adjust the delay time.  
8. Press Control % / fi until “TEST” appears on the display, then press Control @ / # to start  
checking the speaker output balance.  
“TEST” starts flashing on the display, and a test tone comes out of the speakers in the following  
order:  
Left front speaker  
Right front speaker  
Center speaker  
Rear speakers  
Notes:  
• No test tone comes out of the rear speakers when you have selected “3CHLOGIC.”  
• No test tone comes out of the center speaker when you select “PHANTOM” or “OFF” for the center  
mode.  
Front panel  
9. If necessary, adjust the speaker output level as follows:  
• To adjust the rear speaker output level, press Control % / fi until “– REAR +” appears on the  
display, then press Control @ / #.  
• To adjust the center speaker output level, press Control % / fi until “–CENTER+” appears on the  
display, then press Control @ / #.  
Notes:  
• You cannot adjust the left and right rear speaker output level separately.  
• You cannot adjust the rear speaker output level when you have selected “3CHLOGIC.”  
• You cannot adjust the center speaker output level when you select “PHANTOM” or “OFF” for the  
center mode.  
Front panel  
Page 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Press Control  
test tone.  
                                            
%
                                            
/
                                               
fi
                                               
until “TEST” appears on the display, then press Control  
                                                                                         
@
                                                                                         
/
                                                                                            
#
                                                                                            
to stop the  
11. Press Control % / fi until “CNT TONE” (Center Tone) appears on the display.  
12. Press Control @ / # to select the center tone you want.  
The center tone adjustment affects the mid-frequency range, which the human voice is mostly made  
up of.  
Each time you press the button, the display changes to show the following:  
SOFT2  
SOFT1  
FLAT  
SHARP1  
SHARP2  
To make the dialogue clearer, select “SHARP1” (little) or “SHARP2” (much).  
To make the dialogue softer, select “SOFT1” (little) or “SOFT2” (much).  
When “FLAT” is selected, no adjustment is applied.  
Front panel  
Note:  
The center tone cannot be adjusted when sounds do not come out of the center speaker.  
From the remote control:  
Note:  
If you want to use the remote control for adjusting the center mode and the center tone, use the menu function  
(see page 40).  
1. Press SURROUND MODE until “PROLOGIC” or “3CHLOGIC” whichever you want appears  
on the display.  
SURROUND  
MODE  
The PRO LOGIC or 3CH LOGIC indicator (as well as the SURROUND indicator) also lights up.  
Each time you press the button, the surround modes change as follows (the indicator of the selected  
surround mode also lights up on the display):  
Remote: Outside  
PROLOGIC  
3CHLOGIC  
HALL  
SURR OFF  
(Surround Off)  
SOUND  
CONTROL  
2. Open the outside panel and press SOUND CONTROL on the remote mode section.  
The remote control is activated for adjusting the sound.  
DELAY  
3. Press DELAY to adjust the delay time of the rear speaker output.  
2
Each time you press the button, the delay time changes as follows:  
DELAY 1  
DELAY 4  
DELAY 2  
DELAY 3  
Remote: Inside  
Note:  
When you have selected “3CHLOGIC,” you cannot adjust the delay time.  
Continued to the next page  
Page 34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TEST  
4. Press TEST to start checking the speaker output balance.  
6
“TEST” starts flashing on the display, and a test tone comes out of the speakers in the following  
order:  
Left front speaker  
Right front speaker  
Center speaker  
Rear speakers  
Remote: Inside  
Notes:  
• No test tone comes out of the rear speakers when you have selected “3CHLOGIC.”  
• No test tone comes out of the center speaker when you select “PHANTOM” or “OFF” for the center  
mode.  
+
–
REAR  
+
–
CENTER  
5. If necessary, adjust the speaker output level as follows:  
• To adjust the rear speaker output level, press REAR +/–.  
• To adjust the center speaker output level, press CENTER +/–.  
3
4
7/P  
8
Pressing – decreases the output level up to –10 dB.  
Pressing + increases the output level up to +10 dB.  
Remote: Inside  
Notes:  
• You cannot adjust the left and right rear speaker output level separately.  
• You cannot adjust the rear speaker output level when you have selected “3CHLOGIC.”  
• You cannot adjust the center speaker output level when you select “PHANTOM” or “OFF” for the  
center mode.  
TEST  
6. Press TEST again to stop the test tone.  
6
Remote: Inside  
Page 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
See also  
page 40.  
MENU  
Using Dolby Surround  
Once you have set the Dolby Surround adjustments, you can use the same adjustment every time you want  
to enjoy Dolby Surround.  
ThereceivermemorizestwosetsofDolbySurroundadjustment;oneforProLogicandtheotherfor3chLogic.  
On the front panel:  
1. Press SURROUND MODE so that the Control % / fi buttons work for selecting the surround  
SURROUND MODE  
modes.  
The lamp next to the button lights up.  
2. Press Control % / fi until “PROLOGIC” or “3CHLOGIC” whichever you want appears on the  
display.  
The PRO LOGIC or 3CH LOGIC indicator (as well as the SURROUND indicator) also lights up.  
Each time you press the button, the surround modes change as follows (the indicator of the selected  
surround mode also lights up on the display):  
PROLOGIC  
3CHLOGIC  
HALL  
Front panel  
SURR OFF  
(Surround Off)  
3. Select and play a sound source which was processed with Dolby Surround and is labeled with  
mark.  
DOLBY SURROUND  
To cancel the surround mode, press Control % / fi until “SURR OFF” appears in step 2 above.  
The indicator of the selected mode goes off.  
From the remote control:  
1. Press SURROUND MODE until the surround mode you want appears on the display.  
The PRO LOGIC or 3CH LOGIC indicator (as well as the SURROUND indicator) also lights up.  
Each time you press the button, the surround modes change as follows (the indicator of the selected  
surround mode also lights up on the display):  
SURROUND  
MODE  
Remote: Outside  
PROLOGIC  
3CHLOGIC  
HALL  
SURR OFF  
(Surround Off)  
2. Select and play a sound source which was processed with Dolby Surround and is labeled with  
mark.  
DOLBY SURROUND  
To cancel the surround mode, press SURROUND MODE until “SURR OFF” appears on the display.  
The indicator of the selected mode and the SURROUND indicator go off.  
Page 36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the On-Screen Display to Control the Receiver  
You can use the menu function on the TV screen to control the receiver.  
To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 10),  
and set the TV’s input mode to the appropriate position to which the receiver is connected.  
When the TV’s input mode is for TV, you cannot see the on-screen display.  
IMPORTANT:  
When you use the menu functions, make sure that you have connected a TV and operate the  
menu function while watching the on-screen displays on the TV.  
Ba s ic P r ocedur es  
From the remote control:  
1. Press MENU.  
Menu function buttons  
The MAIN MENU appears on the TV screen.  
• If you press % / fi / @ / #, a sub-menu you can adjust at that time appears on the TV  
screen instead of the MAIN MENU.  
MENU  
MENU  
EXIT  
2. Press % / fi to move  
to the sub-menu you want to set, then press @ / # .  
The sub-menu you want appears.  
3. If necessary, press % / fi / @ / # to set or adjust the item you want on the selected sub-  
ON SCREEN CONTROL  
menu.  
When a item is selected, the item will be highlighted.  
Note:  
Moving  
press @ / # to highlight it.  
to an item does not mean that you have selected it. If the item is not highlighted,  
MAIN MENU  
4. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
To go back to the MAIN MENU any time during the process  
Press MENU again.  
Shows the buttons you can use on the current menu. In this case, press % / fi  
to move  
up and down, and @ / # to select the item. (The menus are  
shown on the TV for about one minute.)  
S elect ing t he S our ce t o P la y (Also see page 12)  
SOURCE menu  
1. Press MENU.  
The MAIN MENU appears on the TV.  
2. Press % / fi to move  
to “SOURCE,” then press @ / #.  
The SOURCE menu appears.  
3. Press % / fi to move  
to the source you want to play.  
4. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
Adjus t ing t he Fr ont S pea ker Out put Ba la nce (Also see page 15)  
SETTING menu  
1. Press MENU.  
The MAIN MENU appears on the TV.  
2. Press % / fi to move  
to “SETTING,” then press @ / #.  
The SETTING menu appears.  
3. Press % / fi to move  
to “BAL.” (Balance).  
4. Press @ / # repeatedly to adjust the balance.  
Shows the buttons you can use on  
the current menu.  
5. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
In this case, press % / fi to  
move  
up and down, and @ / #  
to adjust or set the item.  
Page 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Lis t ening a t Low Volum e (Loudnes s ) (Also see page 15)  
1. Press MENU.  
The MAIN MENU appears on the TV.  
2. Press % / fi to move  
to “SETTING,” then press @ / #.  
SETTING menu  
The SETTING menu appears.  
3. Press % / fi to move  
to “LOUDNESS.”  
4. Press @ / # to set the loudness function to “ON” or “OFF.”  
5. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
Us ing t he S leep Tim er (Also see page 16)  
1. Press MENU.  
The MAIN MENU appears on the TV.  
2. Press % / fi to move  
to “SETTING,” then press @ / #.  
SETTING menu  
The SETTING menu appears.  
3. Press % / fi to move  
to “SLEEP TIMER.”  
4. Press @ / # to set the shut-off time.  
5. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
S elect ing t he Cent er S pea ker S ize (Also see page 17)  
Note:  
When the surround mode is “OFF” or “HALL,” you cannot select the center speaker size.  
SETTING menu  
1. Press MENU.  
The MAIN MENU appears on the TV.  
2. Press % / fi to move  
to “SETTING,” then press @ / #.  
The SETTING menu appears.  
3. Press % / fi to move  
to “CENTER SPK” (Center Speaker).  
4. Press @ / # repeatedly until the appropriate center speaker size is selected.  
5. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
Us ing Vis ua l Confir m a t ion (Also see page 18)  
1. Press MENU.  
The MAIN MENU appears on the TV.  
SETTING menu  
2. Press % / fi to move  
to “SETTING,” then press @ / #.  
The SETTING menu appears.  
3. Press % / fi to move  
to “VISUAL CONFIRM.” (Visual Confirmation).  
4. Press @ / # to set Visual Confirmation to “ON” or “OFF.”  
5. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
Page 38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Oper a t ing t he Tuner  
TUNER menu  
1. Press MENU.  
The MAIN MENU appears on the TV.  
2. Press % / fi to move  
to “TUNER,” then press @ / #.  
The TUNER menu appears.  
3. Press % / fi to move  
to the item you want to set or adjust, then press @ / #.  
On the TUNER menu, you can do the following:  
If you have assigned the  
name to this preset station, it  
appears here.  
“CH.”:  
Select a preset channel station. (See page 21)  
If you want to assign a name to a preset channel, see page 22.  
Select the band. (See page 20)  
“BAND”:  
“TUNING”:  
“FM MODE”:  
Tune in a station manually. (See page 20)  
Select the FM reception mode. (See page 21)  
RDS Information menu  
“RDS Information”:Shows the RDS Information on the screen. (See page 23)  
4. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
S elect ing Your Fa vor it e S EA M ode (Also see page 27)  
1. Press MENU.  
The MAIN MENU appears on the TV.  
SEA MODE menu  
2. Press % / fi to move  
to “SEA,” then press @ / #.  
The SEA MODE menu appears.  
3. Press % / fi to move  
to the SEA mode you want.  
4. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
Cr ea t ing Your Own S EA M ode (Also see page 28)  
1. Press MENU.  
The MAIN MENU appears on the TV.  
SEA ADJUST menu  
2. Press % / fi to move  
to “SEAADJUST” then press @ / #.  
The SEAADJUST menu appears.  
3. Press % / fi / @ / # to adjust the SEA mode as you want.  
@ / #: Select the frequency ranges to adjust.  
% / fi: Adjust the frequency levels.  
4. Press MEMORY (next to the SEAADJUST button).  
5. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
Page 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S elect ing t he S ur r ound M odes (Also see pages 29, 32 and 36)  
1. Press MENU.  
The MAIN MENU appears on the TV.  
2. Press % / fi to move  
to “SURROUND,” then press @ / #.  
SURROUND MODE menu  
The SURROUND MODE menu appears.  
3. Press % / fi to move  
to one of the surround modes.  
If you want to adjust the selected mode, go to the following steps.  
4. Press MENU.  
The MAIN MENU appears on the TV again.  
5. Press % / fi to move  
to “SURROUND ADJUST,” then press @ / #.  
The adjustment menu for the mode you have selected in step 3 appears.  
6. Press % / fi to move  
to the item you want to set or adjust, then press @ / #.  
On these adjustment menus, you can do the following:  
PRO LOGIC adjustment menu  
For Dolby Pro Logic:  
“CENTER MODE”: Select the center mode.  
“TEST”:  
Output a test tone.  
“CENTER”:  
“REAR”:  
“DELAY”:  
Adjust the center speaker output level.  
Adjust the rear speaker output level.  
Adjust the delay time of the rear speaker sound.  
Select the center tone.  
“CENTER TONE”:  
3CH LOGIC adjustment menu  
For Dolby 3ch Logic:  
“CENTER MODE”: Select the center mode.  
“TEST”:  
Output a test tone.  
“CENTER”:  
“CENTER TONE”:  
Adjust the center speaker output level.  
Select the center tone.  
For JVC HALL Surround:  
“REAR”:  
HALL Surround adjustment  
menu  
Adjust the rear speaker output level.  
“DELAY”:  
Adjust the delay time of the rear speaker sound.  
7. When you finish, press MENU EXIT.  
The menu disappears from the TV.  
Page 40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPU LINK Remote Control System  
The COMPU LINK remote control system allows you to operate JVC audio components through the remote  
sensor on the receiver.  
To use this remote control system, you need to connect JVC audio components through the COMPU LINK-  
3 (SYNCHRO) jacks (see below) in addition to the connections using cables with RCA pin plugs (see page  
9).  
CD player  
Cassette deck  
COMPU LINK – 3  
(SYNCHRO)  
Turntable  
Notes:  
• If your audio component has two COMPU LINK-3 (SYNCHRO) jacks, you can use either one. If it has only  
oneCOMPULINK-3(SYNCHRO)jack, connectitsothatitisthelastitemintheseriesofcomponents. (For  
example, the turntable or CD player in the diagram above.)  
• Refer also to the manuals supplied with your audio components.  
This remote control system allows you to use four functions listed below.  
7
Remote Control through the Remote Sensor on the Receiver  
You can control the connected audio components through the remote sensor on the receiver using this remote  
control. For details, see pages 42 and 43.  
Note:  
Aim the remote control directly at the remote sensor on the receiver.  
7
Automatic Source Selection  
When you press the play (3) button on a connected component or on its own remote control, the receiver  
automatically turns on and changes the source to the component. On the other hand, if you select a new source  
on the receiver or the remote control, the selected component begins playing immediately.  
In both cases, the previously selected source continues playing without sound for a few seconds.  
7
Automatic Power On/Off (Standby) (only possible with the COMPU LINK-3 connection)  
Both the CD player and cassette deck turn on and off (into standby mode) along with the receiver.  
When you turn on the receiver, the CD player or cassette deck will turn on automatically, depending on which  
component has been previously selected.  
When you turn off the receiver (into standby mode), both the CD player and cassette deck will turn off (into  
standby mode).  
7
Synchronized Recording  
Synchronized recording means the cassette deck starts recording as soon as a CD or a record begins playing.  
To use synchronized recording, follow these steps:  
1
2
Put a tape in the cassette deck, and a disc in the CD player (or a record on the turntable).  
Press the record () button and the pause (8) button on the cassette deck at the same time.  
This puts the cassette deck into recording pause.  
Note:  
Ifyoudonotpresstherecord()buttonandpause(8)buttonatthesametime,thesynchronizedrecording  
feature will not operate.  
3
Press the play (3) button on the CD player or on the turntable.  
The source changes on the receiver, and as soon as play starts, the cassette deck starts recording.  
When the play ends, the cassette deck enters recording pause, and stops about 4 seconds later.  
Notes:  
• During synchronized recording, the selected source cannot be changed.  
• IfyourCDplayerisplayinginprogrammode,a4-secondblankisrecordedbetweentrackssothat themusic  
scan feature of your cassette deck can be used on the recorded tape.  
• If the power of any component is shut off during synchronized recording, the COMPU LINK remote control  
system may not operate properly. In this case, you must start again from the beginning.  
Page 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control  
Using this remote control, you can operate audio/video components of not only JVC’s but also the other  
manufacturers’. To operate the other manufacturers’ components, see page 47.  
Using the Remote Control for Operating JVC Audio/Video Components  
IMPORTANT:  
To operate JVC audio components using this remote control:  
• You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see page  
41) in addition to the connections using cables with RCA pin plugs (see page 9).  
• Aim the remote control directly at the remote sensor on the receiver.  
• Select a source with the buttons on the SOURCE SELECT section (outside panel) of the remote control,  
or press the buttons on the remote mode section (inside panel) of the remote control. If you select a source  
on the front panel or using the menu function, the remote control will not operate that source.  
Tuner  
FM  
AM  
After pressing FM or AM (on the SOURCE SELECT section of the outside panel) or TUNER (on the remote  
mode section of the inside panel), you can perform the following operations on the built-in tuner:  
Remote: Outside  
1 – 10, +10  
Selects the preset channels directly.  
TUNER  
For preset channel number 5, press 5.  
For preset channel number 15, press +10, then 5.  
For preset channel number 20, press +10, then 10.  
For preset channel number 30, press +10, +10, then 10.  
Changes the FM reception mode.  
DELAY  
+
–
CENTER  
REAR  
1
5
9
2
3
4
+
–
TEST  
FM MODE/MUTE  
PRESET CHANNEL +/–  
RDS operating buttons  
PTY SEARCH  
6
7/P  
8
Changes the preset channels.  
FM  
MODE/MUTE  
10  
0
+10  
Starts and ends searching a broadcast using the RDS.  
Selects a program type.  
Changes the RDS display mode.  
PRESET  
CHANNEL  
TV  
VOLUME  
PTY SELECT +/–  
DISPLAY MODE  
PTY SELECT  
PTY SELECT  
+
–
PTY SEARCH  
DISPLAY MODE  
TV/VIDEO  
TAPE  
Note:  
To activate the remote control for tuner operations, you can use the FM button or the AM button on the  
SOURCE SELECT section or the TUNER button on the remote mode section. If you press the button on  
the remote mode section, you can operate the tuner using the remote control, but the playing source will  
not be changed to “FM” or “AM.”  
Remote: Inside  
Sound control section (Amplifier)  
You can always perform the following operations:  
SURROUND  
MODE  
SURROUND MODE  
SEA MODE  
Changes the surround modes.  
Changes the SEA modes.  
SEA  
MODE  
Remote: Outside  
After pressing SOUND CONTROL on the remote mode section of the inside panel, you can perform the  
following operations:  
SOUND  
CONTROL  
CENTER +/–  
REAR +/–  
DELAY  
Changes the center speaker output level for the surround modes.  
Changes the left/right rear speaker output level for surround modes.  
Changes the delay time for surround modes.  
Remote: Inside  
TEST  
Checks the speaker output level for surround modes.  
DELAY  
+
–
CENTER  
1
5
9
2
3
4
Note:  
+
–
REAR  
TEST  
After adjusting sounds, press the corresponding button on the remote mode section to operate your target  
source by using 10 keys; otherwise, 10 keys cannot be used for operating your target source.  
6
7/P  
8
FM  
MODE/MUTE  
10  
0
+10  
PRESET  
CHANNEL  
TV  
VOLUME  
PTY SELECT  
PTY SELECT  
+
–
PTY SEARCH  
DISPLAY MODE  
TV/VIDEO  
TAPE  
Remote: Inside  
Page 42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD player  
CD  
AfterpressingCD(eitherontheSOURCESELECTsectionoftheoutsidepanelorontheremotemodesection  
of the inside panel), you can perform the following operations on a CD player:  
Remote: Outside  
CD  
3
Starts playing.  
4
¢
7
Returns to the beginning of the current (or previous) track.  
Skips to the beginning of the next track.  
Stops playing.  
DELAY  
+
–
CENTER  
REAR  
1
5
9
2
3
4
8
Stops playing temporarily. To release it, press 3.  
+
–
TEST  
6
7/P  
8
1 — 10, +10 Selects a track number directly  
For track number 5, press 5.  
FM  
MODE/MUTE  
For track number 15, press +10, then 5.  
10  
0
+10  
PRESET  
CHANNEL  
TV  
VOLUME  
For track number 20, press +10, then 10.  
For track number 30, press +10, +10, then 10.  
PTY SELECT  
PTY SELECT  
+
–
PTY SEARCH  
DISPLAY MODE  
TV/VIDEO  
TAPE  
Note:  
To activate the remote control for CD operations, you can use either one of the CD buttons — the one on  
the SOURCE SELECT section; the other on the remote mode section. If you press the one on the remote  
mode section, you can operate the CD player using the remote control, but the playing source will not be  
changed to “CD.”  
Remote: Inside  
CD player-changer  
CD DISC  
After pressing CD DISC (on the remote mode section of the inside panel), you can perform the following  
operations on a CD player-changer:  
DELAY  
+
–
CENTER  
1
5
2
3
4
3
Starts playing.  
+
–
REAR  
TEST  
4
Returns to the beginning of the current (or previous) track.  
Skips to the beginning of the next track.  
Stops playing.  
Stops playing temporarily. To release it, press 3.  
Select the number of a disc installed in a CD player-changer.  
6
7/P  
8
¢
PTY SELECT  
PTY SELECT  
+
7
–
PTY SEARCH  
DISPLAY MODE  
TV/VIDEO  
TAPE  
8
1 — 6, 7/P  
Remote: Inside  
Cassette deck  
TAPE  
After pressing TAPE (either on the SOURCE SELECT section of the outside panel or on the remote mode  
section of the inside panel), you can perform the following operations on a cassette deck:  
Remote: Outside  
3
Starts playback.  
TAPE  
1
¡
7
Fast winds the tape from right to left.  
Fast winds the tape from left to right.  
Stops operation.  
Stops playing or recording temporarily. To release it, press 3.  
Press this button with 3 to start recording.  
Press this button with 8 to enter the recording standby mode.  
DELAY  
+
–
CENTER  
REAR  
1
5
9
2
3
4
8
+
–
TEST  
6
7/P  
8
FM  
MODE/MUTE  
10  
0
+10  
Without pressing TAPE (either on the SOURCE SELECT section of the outside panel or on the remote  
mode section of the inside panel), you can always perform the following:  
PRESET  
CHANNEL  
TV  
VOLUME  
TAPE  
Changes the direction of tape running.  
PTY SELECT  
PTY SELECT  
+
–
PTY SEARCH  
DISPLAY MODE  
TV/VIDEO  
TAPE  
Note:  
To activate the remote control for deck operations, you can use either one of the TAPE buttons — the one  
on the SOURCE SELECT section; the other on the remote mode section. If you press the button on the  
remote mode section, you can operate the cassette deck using the remote control, but the playing source  
will not be changed to “TAPE.”  
Remote: Inside  
Turntable  
PHONO  
After pressing PHONO (on the SOURCE SELECT section), you can perform the following operations on a  
turntable:  
Remote: Outside  
PTY SELECT  
PTY SELECT  
+
–
PTY SEARCH  
TV/VIDEO  
3
7
Starts playing.  
Stops playing.  
TAPE  
DISPLAY MODE  
Remote: Inside  
Page 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT:  
To operate JVC video components using this remote control:  
• Some JVC VCR can accept two types of the control signals — remote code “A” and “B.” Before using this  
remotecontrol, makesurethattheremotecontrolcodeoftheVCRconnectedtotheVCRjacksissettocode  
“A.”  
• Aim the remote control directly at the remote sensor on the VCR or TV, not on the receiver.  
• Select a source with the buttons on the SOURCE SELECT section (outside panel) of the remote control,  
or press the buttons on the remote mode section (inside panel) of the remote control. If you select a source  
on the front panel or using the menu function, the remote control will not operate that source.  
VCR  
After pressing VCR (either on the SOURCE SELECT section of the outside panel or on the remote mode  
section of the inside panel), you can perform the following operations on a VCR:  
3
Starts playback  
Rewinds a tape  
Fast winds a tape  
Stops operation.  
Stops playing or recording temporarily. To release it, press 3.  
Press this button with 3 to start recording.  
Press this button with 8 to enter the recording standby mode.  
DELAY  
+
1
¡
7
–
CENTER  
REAR  
1
5
9
2
3
4
+
–
TEST  
6
7/P  
8
8
FM  
MODE/MUTE  
10  
0
+10  
PRESET  
CHANNEL  
TV  
VOLUME  
PRESET CHANNEL +/–  
1 – 9, 0  
Changes the TV channels on the VCR.  
Selects the TV channels on the VCR.  
PTY SELECT  
PTY SELECT  
+
–
PTY SEARCH  
DISPLAY MODE  
TV/VIDEO  
TAPE  
Without pressing VCR (either on the SOURCE SELECT section of the outside panel or on the remote  
mode section of the inside panel), you can always perform the following:  
TV/VIDEO  
Switches the TV tuner output mode.  
VCR (on the POWER section of the outside panel)  
Turns on/off the VCR.  
Remote: Inside  
Note:  
To activate the remote control for VCR operations, you can use either one of the VCR buttons — the one  
ontheSOURCESELECTsection;theotherontheremotemodesection. Ifyoupresstheoneontheremote  
mode section, you can operate the VCR using the remote control, but the playing source will not be  
changed to “VCR.”  
TV  
After pressing TV SOUND (on the SOURCE SELECT section of the outside panel) or TV (on the remote  
mode section of the inside panel), you can also perform the following operations on the TV:  
DELAY  
+
–
CENTER  
REAR  
1 – 9, 0, +10  
Selects the TV channels.  
1
5
9
2
3
4
+10buttonwillfunctionastheENTERbuttonifyourTVrequirespressing  
the ENTER button after selecting a channel number.  
Changes the TV channels.  
+
–
TEST  
6
7/P  
8
PRESET CHANNEL +/–  
FM  
MODE/MUTE  
10  
0
+10  
Without pressing TV SOUND (on the SOURCE SELECT section of the outside panel) or TV (on the  
remote mode section of the inside panel), you can always perform the following:  
PRESET  
CHANNEL  
TV  
VOLUME  
TV VOLUME +/–  
Changes the TV volume.  
PTY SELECT  
TV (on the POWER section of the outside panel)  
PTY SELECT  
+
–
PTY SEARCH  
DISPLAY MODE  
TV/VIDEO  
TAPE  
Turns on/off the TV.  
Note:  
To activate the remote control for TV operations, you can use either the TV SOUND button on the  
SOURCE SELECT section or the TV button on the remote mode section. If you press TV on the remote  
mode section, you can operate the TV using the remote control, but the playing source will not be changed  
to “TV SOUND.”  
Remote: Inside  
Page 44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Simplifying the Operations Using the Remote Control  
You can program and store a series of operations in a specific order you want. After making a program, you  
can perform these programed operations at a press of the SEQUENTIAL PROGRAM KEY.  
Programing a series of operations  
You can make 3 different programs, each containing up to 16 steps.  
1
2
Open the outside panel of the remote control.  
LEARN  
CANCEL  
Press LEARN so that the SEND/LEARN indicator lights up (green).  
Lights  
SEND/LEARN  
ERROR  
3
4
Close the outside panel.  
Remote: Inside  
Press SEQUENTIAL PROGRAM KEY A, B, or C to which you want to assign a program you  
are making from now.  
SEQUENTIAL PROGRAM KEY  
A
B
C
The SEND/LEARN indicator starts flashing.  
Flashes  
SEND/LEARN  
ERROR  
Remote: Outside  
Note:  
If the ERROR indicator lights up (red) while the SEND/LEARN indicator is flashing, you have already  
assignedaprogramtothatSEQUENTIALPROGRAMKEY. Toaddstepstotheprogram, continuetostep  
5. If you do not want to change it, press another SEQUENTIAL PROGRAM KEY after the SEND/LEARN  
indicator stops flashing.  
5
While the SEND/LEARN indicator is flashing, press the button you want to store as the first  
step of the program.  
Both the SEND/LEARN and ERROR indicators light up, and then only the ERROR indicator goes  
off.  
SEND/LEARN  
SEND/LEARN  
ERROR  
ERROR  
Lights  
Lights  
Lights  
SEND/LEARN  
ERROR  
When the SEND/LEARN indicator goes off and starts flashing again, the first step is stored.  
The ERROR indicator lights up while the SEND/LEARN indicator is flashing.  
SEND/LEARN  
ERROR  
Flashes  
Lights  
SEND/LEARN  
ERROR  
Note:  
If the SEND/LEARN indicator stops flashing before you press the button, repeat from step 4 again.  
Page 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Repeat step 5 until you program up to 16 steps.  
Notes:  
• If the ERROR indicator flashes several times, you cannot program this step.  
– 16 steps are already programed or this particular step is not programmable.  
• You cannot program an operation performed by pressing two buttons at the same time — like pressing  
and 3 at the same time to start recording.  
• Do not program a TV operation step immediately after the step of turning on the TV. The TV operation  
may be ignored since the TV is not yet ready to accept the signal.  
LEARN  
CANCEL  
7
Press LEARN again to finish the programing procedure.  
Both the SEND/LEARN and ERROR indicators go off.  
SEND/LEARN  
ERROR  
Remote: Inside  
CAUTION:  
Whenreplacingthebatteries, finishitwithoutdelay;otherwise, thestoredsignalsareallerased.  
Erasing a program  
1
2
Open the outside panel of the remote control.  
Press LEARN so that the SEND/LEARN indicator lights up (green).  
LEARN  
CANCEL  
Lights  
SEND/LEARN  
ERROR  
Remote: Inside  
3
4
Press CANCEL.  
Both the SEND/LEARN and ERROR indicators light up.  
LEARN  
CANCEL  
SEND/LEARN  
ERROR  
Remote: Inside  
Lights  
Lights  
SEND/LEARN  
ERROR  
Close the outside panel, and press and hold SEQUENTIAL PROGRAM KEY A, B, or C to  
which the program you want to erase has been assigned to, until both the SEND/LEARN and  
ERROR indicators start flashing.  
SEQUENTIAL PROGRAM KEY  
A
B
C
SEND/LEARN  
ERROR  
Flashes  
Lights  
Remote: Outside  
Flashes  
SEND/LEARN  
ERROR  
SEND/LEARN  
ERROR  
Note:  
If the ERROR indicator remains lit, no program is assigned to the SEQUENTIAL PROGRAM KEY.  
In this case, press CANCEL to turn off the ERROR indicator.  
LEARN  
CANCEL  
5
Press LEARN again to finish the erasing procedure.  
The SEND/LEARN indicator goes off.  
Remote: Inside  
SEND/LEARN  
ERROR  
Page 46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating the Other Manufacturers’ Audio/Video Components  
The remote control supplied with the receiver can learn and memorize the signals used for the other  
manufactures’ remote control unit. By storing these signals, you can operate the other manufacturers’ audio/  
video components.  
Storing the signals  
Before storing another manufacturer’s signals, make sure that manufacturer’s remote control unit (hereafter  
called “target remote control”) actually works.  
1
Place the two remote controls on a level surface with signal transmitting windows facing each  
other.  
Leave a space of 5 to 10 cm (2 to 4 inches) between the two remote controls; otherwise, storing may  
be failed.  
5 to 10 cm  
(2 to 4 inches)  
2
3
Open the outside panel of this remote control.  
Press LEARN so that the SEND/LEARN indicator lights up (green).  
LEARN  
CANCEL  
Lights  
SEND/LEARN  
ERROR  
Remote: Inside  
EXT.1  
4
Press one of the buttons on the remote mode section.  
If possible, select the source corresponding to the target remote control’s usage.  
TV  
VCR  
EXT.2  
SEND/LEARN  
ERROR  
CD  
TAPE  
Lights  
SEND/LEARN  
ERROR  
Notes:  
• Since no signal have been preset for the EXT.1 and EXT.2 modes, you can store signals from the target  
remote control without losing any preset signals.  
Remote: Inside  
• If you want to store a signal into the TV or VCR button on the POWER section, you can skip this step.  
Buttons you can assign  
signals to  
5
Press one of the buttons (illustrated to the left), to which you want to assign a signal from the  
target remote control.  
The SEND/LEARN indicator starts flashing.  
TV  
VCR  
Remote: Outside  
SEND/LEARN  
SEND/LEARN  
ERROR  
ERROR  
DELAY  
+
–
CENTER  
1
5
9
2
3
4
Flashes  
+
–
REAR  
TEST  
6
7/P  
8
FM  
Note:  
MODE/MUTE  
10  
0
+10  
If the ERROR indicator lights red, you have already stored a signal. To change the stored signal, go to  
the next step. If you do not want to change it, press another button.  
PRESET  
CHANNEL  
TV  
VOLUME  
PTY SELECT  
PTY SELECT  
6
While the SEND/LEARN indicator is flashing, press the button on the target remote control,  
the signal of which you want to assign to the button of this remote control you have pressed in  
step 5.  
+
–
PTY SEARCH  
DISPLAY MODE  
TV/VIDEO  
TAPE  
The SEND/LEARN indicator stops flashing and remains lit, and the ERROR indicator also lights red  
but soon goes off.  
Remote: Inside  
SEND/LEARN  
SEND/LEARN  
SEND/LEARN  
ERROR  
ERROR  
ERROR  
Lights  
Lights  
Lights  
Page 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
After several seconds, the SEND/LEARN indicator goes off and lights up again. This means that the  
storing is successfully finished.  
SEND/LEARN  
ERROR  
Lights  
SEND/LEARN  
ERROR  
Notes:  
• If the SEND/LEARN indicator stops flashing before you press the button on the target remote control,  
repeat from step 5 again.  
• If the ERROR indicator lights red and does not go off, you have failed in storing the signal.  
• If the ERROR indicator flashes, you have failed in storing the signal. Try again. However some signals  
do not match to this remote control even though this remote control can lean most infrared signals.  
7
8
Repeat steps 5 to 6 to store more signals in the same remote mode.  
Repeat steps 4 to 6 to store more signals in a different remote mode.  
Press LEARN to finish the storing procedure.  
LEARN  
CANCEL  
SEND/LEARN  
ERROR  
Note:  
The signals stored into this remote control from the target remote control deviates slightly from the  
original signals. Since some components will not accept these deviating signals, you may not be able to  
operate those components using this remote control even though the storing procedure has been  
successfully finished.  
Remote: Inside  
CAUTION:  
Whenreplacingthebatteries, finishitwithoutdelay;otherwise, thestoredsignalsareallerased.  
Using stored signals  
When you want to use the stored signals, follow the procedure below.  
EXT.1  
1
2
3
Open the outside panel of the remote control.  
Press one of the remote mode buttons.  
Press the desired button.  
TV  
VCR  
EXT.2  
CD  
TAPE  
Note:  
WhenyouhavestoredsignalsintotheTVandVCRbuttons, simplypressingthebuttonwillsendthestored  
signals. You do not have to press a remote mode button.  
DELAY  
+
–
CENTER  
REAR  
1
5
9
2
3
4
+
–
TEST  
6
7/P  
8
TV  
VCR  
FM  
MODE/MUTE  
10  
0
+10  
Remote: Outside  
PRESET  
CHANNEL  
TV  
VOLUME  
PTY SELECT  
PTY SELECT  
+
–
PTY SEARCH  
DISPLAY MODE  
TV/VIDEO  
TAPE  
Remote: Inside  
Page 48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Erasing stored signals  
After erasing stored signals, preset signals are resumed and you can operate JVC’s components again.  
1
2
Open the outside panel of the remote control.  
Press LEARN so that the SEND/LEARN indicator lights up (green).  
LEARN  
CANCEL  
Lights  
SEND/LEARN  
ERROR  
Remote: Inside  
3
Press CANCEL.  
Both the SEND/LEARN and ERROR indicators light up.  
LEARN  
CANCEL  
SEND/LEARN  
ERROR  
Remote: Inside  
Lights  
Lights  
SEND/LEARN  
ERROR  
EXT.1  
4
Press and hold the one of the buttons on the remote mode section until both the SEND/LEARN  
and ERROR indicators start flashing.  
TV  
VCR  
EXT.2  
All the signals assigned in the selected remote mode are erased at the same time.  
You cannot erase a signal assigned to a particular button only.  
CD  
TAPE  
SEND/LEARN  
SEND/LEARN  
ERROR  
ERROR  
Remote: Inside  
Flashes  
Lights  
Flashes  
SEND/LEARN  
ERROR  
Note:  
If the ERROR indicator remains lit, no signals are assigned to the buttons in the selected remote mode.  
In this case, press CANCEL to turn off the ERROR indicator.  
LEARN  
CANCEL  
5
Press LEARN again to finish the erasure.  
The SEND/LEARN indicator goes off.  
SEND/LEARN  
ERROR  
Remote: Inside  
Page 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact  
your JVC service center.  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
The display does not light  
up.  
The power cord is not plugged in Plug the power cord into an AC outlet  
or the POWER switch is  
pressed to set in the —OFF  
position.  
and/or press POWER to set it in the  
_ON position.  
No sound from speakers.  
Speaker signal cables are not  
connected.  
Check speaker wiring and  
reconnect if necessary.  
The SPEAKERS 1 and 2 buttons Press SPEAKERS 1 and 2 correctly.  
are not set correctly.  
An incorrect source is selected.  
Mute is activated.  
Select the correct source.  
Press MUTE to cancel the mute.  
Sound from one speaker  
only.  
Speaker signal cables are not  
connected properly.  
Check speaker wiring and reconnect if  
necessary.  
The balance is set to one extreme. Adjust the balance properly.  
Continuous hiss or buzzing  
during FM reception.  
Incoming signal is too weak.  
Connect an outside FM antenna or  
contact your dealer.  
The station is too far away.  
An incorrect antenna is used.  
Select a new station.  
Check with your dealer to be sure you  
have a correct antenna.  
Antennas are not connected  
properly.  
Check connections.  
Occasional cracking noise  
during FM reception.  
Ignition noise from automobiles. Move the antenna farther from  
automobile traffic.  
No colors on the on-screen  
display.  
The color system of the  
connected TV is not PAL.  
Connect a PAL TV.  
Howling during record  
playing.  
Your turntable is too close to  
speakers.  
Move speakers away from the  
turntable.  
Remote control does not  
work.  
Stored control signals are erased. Store the control signals again.  
There is an obstruction in front of Remove the obstruction.  
the remote sensor on the receiver.  
Batteries are weak.  
Replace batteries.  
Page 50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Amplifier  
Output Power  
At Stereo operation  
Front Channels  
80 watts per channel, min. RMS, both channels driven into 4  
ohms at 1 kHz with no more than 0.9% total harmonic distortion.  
(IEC268-3/DIN)  
70 watts per channel, min. RMS, both channels driven into 8  
ohms at 1 kHz with no more than 0.9% total harmonic distortion.  
(IEC268-3/DIN)  
65 watts per channel, min. RMS, both channels driven into 8  
ohms, 20 Hz to 20 kHz with no more than 0.06% total harmonic  
distortion.  
At Surround operation  
Front Channels  
70wattsperchannel, min. RMS, driveninto8ohmsat1kHzwith  
no more than 0.7% total harmonic distortion.  
Center Channel  
Rear Channels  
70 watts, min. RMS, driven into 8 ohms at 1 kHz, with no more  
than 0.7% total harmonic distortion.  
70 watts per channel, min. RMS, driven into 8 ohms at 1 kHz,  
with no more than 0.7% total harmonic distortion.  
Total Harmonic Distortion  
(8 ohms, 1 kHz)  
0.06 %* at 65 watts output  
(* Measured by JVC Audio Analysis System)  
Audio Input Sensitivity/  
Impedance (1 kHz)  
PHONO (MM)  
CD, VCR, VIDEO1, VIDEO2,  
TV SOUND, TAPE  
2.5 mV/47 k ohms  
230 mV/47 k ohms  
Audio Output Level  
TAPE, VCR  
230 mV  
Signal-to-Noise Ratio  
(’66 IHF/DIN)  
PHONO  
CD, VCR, VIDEO1, VIDEO2,  
TV SOUND, TAPE  
70 dB/66 dB  
87 dB/67 dB  
Frequency Response (8 ohms)  
RIAA Phono Equalization  
PHONO  
CD, VCR, VIDEO1, VIDEO2,  
TV SOUND, TAPE  
20 Hz to 20 kHz (±1 dB)  
20 Hz to 20 kHz (±1 dB)  
±0.5 dB (20 Hz to 20 kHz)  
Loudness Control  
(Volume Control at –40 dB)  
+6 ±1 dB at 100 Hz  
+4 ±1 dB at 10 kHz  
S.E.A.  
Center Frequencies  
Control Range  
100 Hz, 1 kHz, 10 kHz  
±10 dB ±2 dB  
Video  
Video Input Sensitivity/Impedance VCR, VIDEO1, VIDEO2  
1 Vp-p/75 ohms  
1 Vp-p (at 1 Vp-p input)  
Negative  
Video Output Level  
Synchronization  
VCR, MONITOR OUT  
Signal-to-Noise Ratio  
On-Screen Color System  
45 dB  
PAL  
Page 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FM tuner (IHF)  
Tuning Range  
87.5 MHz to 108.0 MHz  
Usable Sensitivity  
Monaural  
10.8 dBf (0.95 µV/75 ohms)  
50 dB Quieting Sensitivity  
Monaural  
Stereo  
16.3 dBf (1.8 µV/75 ohms)  
38.3 dBf (22.5 µV/75 ohms)  
Signal-to-Noise Ratio  
(IHF-A weighted)  
Monaural  
Stereo  
80 dB at 85 dBf  
73 dB at 85 dBf  
Total Harmonic Distortion  
Monaural  
Stereo  
0.15 % at 1 kHz  
0.2 % at 1 kHz  
Stereo Separation at REC OUT  
Capture Ratio  
40 dB at 1 kHz  
1.5 dB (10 mV)  
Alternate Channel Selectivity  
Frequency Response  
60 dB: (±400 kHz)  
30 Hz to 15 kHz: (+0.5 dB, –3 dB)  
AM (MW/LW) tuner  
Tuning Range  
MW:  
LW:  
522 kHz to 1,629 kHz  
144 kHz to 288 kHz  
Usable Sensitivity  
MW: Loop antenna  
External antenna  
300 µV/m  
30 µV  
LW: Loop antenna  
600 µV/m  
Signal-to-Noise Ratio  
50 dB (100 mV/m)  
General  
Power Requirements  
AC 230V , 50 Hz  
Power Consumption  
Dimensions (W x H x D)  
Mass  
280 watts  
2 watts (in standby mode)  
435 x 156.5 x 412 mm  
(17 3/16 x 6 3/16 x 16 1/4 inches)  
10.3 kg (22.7 lbs)  
Designs & specifications are subject to change without notice.  
Page 52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VICTOR COMPANY OF JAPAN, LIMITED  
J
C
V
0697OFYOTKJEM  
EN, GE, FR, NL, SP, IT  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Insignia CD Player NS P3114 User Manual
Intel Video Gaming Accessories 9800 Pro User Manual
IOGear Network Card GICe702S3R5W6 User Manual
JVC Camcorder LYT2259 002B M User Manual
JVC Car Video System LVT2086 001B User Manual
JVC Flat Panel Television LT Z26S2 User Manual
JVC Satellite Radio KTSR2000J KT SR2000 User Manual
Kalorik Vacuum Cleaner USK HVC 2 User Manual
Kambrook Electric Heater KCE440 User Manual
KitchenAid Coffeemaker KCM222 User Manual