Kambrook Electric Heater KCE440 User Manual

Ceramic  
Tower Heater  
Instruction Booklet  
KCE440  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd  
1
12/10/09 2:26 PM  
Contents  
Kambrook Recommends  
Safety First  
p4  
Your Ceramic Tower Heater  
Quick Start Guide  
p6  
p7  
Using Your Ceramic Tower Heater  
Care and Cleaning  
p8  
p11  
p12  
Warranty Details  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd  
3
12/10/09 2:26 PM  
Kambrook Recommends Safety First  
IMPORTANT: Please retain your  
instruction book for future use.  
At Kambrook, we believe that safe performance is the first priority in any  
consumer product, so that you, our valued customer can confidently  
use and trust our products. We ask that any electrical appliance that  
you use be operated in a sensible fashion with due care and attention  
placed on the following important operating instructions.  
Important Safeguards For Your Kambrook  
Ceramic Tower Heater  
Avoid touching heater body while it is on,  
some parts of the heater are hot.When  
moving the unit switch off and hold the  
heater by the handles where provided.  
Keep combustible materials such as  
drapes and other furnishings at least 1.7  
metres from the front, sides and rear of  
the heater. Do not use heater to dry your  
laundry.  
at the power outlet then unplug heater  
from the power outlet when not in use.  
Do not operate heater whilst asleep.  
Do not operate any heater with a  
damaged cord or plug, or if heater  
has been dropped or damaged in any  
manner. Return heater to your nearest  
service centre for examination, electrical  
or mechanical adjustment or repair.  
Do not use outdoors.This heater is not  
intended for commercial use, such as  
construction sites.  
Do not locate the heater immediately  
below a socket outlet when in use.  
WARNING: In order to  
avoid overheating do  
not cover the heater.  
Do not use this heater with a  
programmer, timer or any other  
device that switches the heater on  
automatically. Since a fire risk may exist  
if the heater is covered or positioned  
incorrectly.  
This heater is not intended for use in wet  
or moist locations. Do not use this heater  
in the immediate surroundings of a bath,  
a shower or a swimming pool. Do not  
immerse or allow liquids to be spilt on  
heater.  
This heater has hot and arcing or  
sparking parts inside. Do not use in areas  
where petrol, paints, aerosols, or other  
inflammable substances are used or  
stored.  
Extreme caution and supervision is  
necessary when this heater is used by or  
near children, invalids or animals.  
This appliance is not intended for use  
by persons (including children) with  
reduced physical, sensory or mental  
capabilities, or lack of experience and  
knowledge, unless they have been given  
supervision or instruction concerning use  
of the appliance by a person responsible  
for their safety.  
Children should be supervised to ensure  
that they do not play with the appliance.  
Important – this heater is intended for  
floor use only.  
Do not operate the heater with the  
power cord damaged, frayed or split,  
wound around any part of the heater, or  
in contact with heated surfaces of the  
heater.  
Do not mount on ceiling or walls.  
Do not leave heater unattended.Always  
switch off the heater at the controls and  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd  
4
12/10/09 2:26 PM  
Do not allow materials that have been  
in contact with oil, petroleum based  
products or drying fluids to come in  
contact with the heater.  
Switch off at the control switch and  
power outlet, then unplug and allow  
heater to cool down before cleaning or  
storing.  
Do not run the cord under carpeting  
or cover the cord with rugs, runners or  
the like.Arrange cord away from traffic  
areas and where it will not be tripped  
over.  
Use this heater only as described in this  
instruction manual.Any other use not  
recommended by the manufacturer  
may cause fire electric shock or injury  
and voids all warranties.  
To disconnect heater turn the power to  
OFF, then turn the control switch to off.  
Turn off at the power outlet then remove  
the plug from its outlet.  
Do not insert or allow foreign objects to  
pass through the inlet or outlet openings.  
This may cause an electric shock, fire or  
damage the heater.  
Regularly inspect the supply cord, plug,  
control settings, air inlets and outlets and  
main housing for any damage. If found  
damaged in any way, immediately  
cease use of the heater and return  
to Kambrook or an authorised service  
agent for inspection or repair.  
To prevent a possible fire or heat  
damage, allow ample space around the  
heater (1.7m at front and 0.5m at the  
rear, top and sides) and do not totally  
or partially block the air inlet or outlets  
in any manner. Check the openings  
from time to time for accumulated  
dust. Ensure long shag carpet does not  
obstruct airflow under the unit.  
NOTE: This Kambrook Ceramic  
Tower Heater is electronically  
controlled and will not operate  
until the heater is plugged into  
a 230V or 240V power point and  
switched on.  
Do not touch hot metal surfaces.  
Important Safeguards For All Electrical  
Appliances  
Fully unwind the power cord before use.  
Any maintenance other than cleaning  
should be performed at an authorised  
Kambrook Service Centre.  
Do not let the power cord hang over  
the edge of a bench or table, touch hot  
surfaces or become knotted.  
This appliance is for household use only.  
Do not use this appliance for anything  
other than its intended use. Do not use  
in moving vehicles or boats. Do not use  
outdoors. Misuse may cause injury.  
The installation of a residual current  
device (safety switch) is recommended  
to provide additional safety protection  
when using electrical appliances. It  
is advisable that a safety switch with  
a rated residual operating current  
not exceeding 30mA be installed in  
the electrical circuit supplying the  
appliance. See your electrician for  
professional advice.  
The appliance is not intended for use by  
persons (including children) with reduced  
physical, sensory or mental capabilities,  
or lack of experience and knowledge,  
unless they have been given supervision  
or instruction concerning use of the  
appliance by a person responsible for  
their safety.  
Children should be supervised to ensure  
that they do not play with the appliance.  
It is recommended to regularly inspect  
the appliance.To avoid a hazard do not  
use the appliance if power cord, power  
plug or appliance becomes damaged  
in any way. Return the entire appliance  
to the nearest authorised Kambrook  
Service Centre for examination and/or  
repair, or contact Customer Service on  
1300 139 798  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd  
5
12/10/09 2:26 PM  
Your Ceramic Tower Heater  
1. 1800 watt ceramic heating  
7. 2 heat setting, plus auto mode  
element for efficient heating  
and fan only setting  
2. LCD screen  
8. 90° degree oscillation for warmth  
throughout the room  
3. ThermoGuard protection for  
peace of mind  
9. On/Off button and variable  
temperature dial, to turn  
the heater on and off and  
to maintain your desired  
temperature setting  
4. Full featured remote control  
5. Power switch  
Control Panel  
10. Power-On indicator  
6. Convenient 8hr  
auto-off timer  
Not Shown  
Convenient carry handle  
Safety tip-over cut-out switch  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd  
6
12/10/09 2:26 PM  
Quick Start Guide  
Setting the  
heating  
mode  
Turning the  
heater on  
Plug the cord  
into a 230V or  
240V power  
point and  
Switch on the  
unit using the  
ON/OFF switch. activate.  
Press the On/  
Off button to  
The heater will  
start operating  
at the HIGH  
heat setting.  
Leave at HIGH  
until the room  
temperature is  
comfortable.  
Press the MODE  
button to  
select the LOW  
heat setting,  
and retain a  
comfortable  
temperature for  
your room.  
switch on.  
Setting the  
variable  
Setting the  
oscillation  
Turning the  
heater off  
temperature  
R
Press the  
Rotate the  
dial clockwise  
to increase  
temperature,  
and anti-  
Press the SWING Press the On/Off Switch off the  
MODE button  
to select AUTO  
setting.  
button to  
button to place unit using the  
activate. Press  
again to stop  
the oscillation.  
the heater in  
ON/OFF switch.  
standby mode.  
clockwise  
to decrease  
temperature.  
Fit window coverings like curtains to  
Hints/Tips to Retain Heat in  
Your Home  
limit winter heat loss  
Put draft stoppers, such as a rolled  
up towel, at the bottom of outside  
doorways to keep out cold air  
Keep the heat in and the cold out by  
installing wall and ceiling insulation.  
Avoid placing items too close to the  
heater (both at the front and back)  
for optimal air flow  
Don’t overheat your home.The  
temperature of a heated room in  
winter should be 18-21°C  
Your heater will work more  
efficiently if you stick to Kambrook’s  
recommended clearance spaces  
Choose the right size heater for the  
room type you want to heat  
Zone off unoccupied rooms by closing  
doors and only heat the main living  
areas  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd  
7
12/10/09 2:26 PM  
Using Your Ceramic Tower Heater  
Remove any promotional material or  
packaging from the heater.  
Setting the Heating Mode  
Unwind the cord to its full length  
and place the heater on a firm, level  
surface in a stable upright position.  
Visually inspect the air inlet and outlets  
to ensure there are no blockages.  
When unpacking the heater, check  
to see you have received the remote  
control, before discarding the  
packaging.  
Turning Your Heater On  
Plug the cord into a 230V or 240V  
power point and switch on.  
To activate the heater, press the On/  
Off button.The heater will start  
operating on the HIGH heat setting  
(1800 watts) and the LCD screen will  
illuminate, displaying the ambient  
room temperature and heat setting.  
NOTE: To avoid an electrical  
circuit overload, it is  
recommended that no other  
appliances are plugged into  
the same circuit as your heater,  
when it is in use.  
NOTE: After several seconds,  
the LCD screen will fade, but  
the heater settings will remain  
visible.  
Turn the heater on by switching the  
Power  
switch located on the right  
hand side of the base, to the on  
position.An audible beep will sound,  
and the red power indicator light  
will illuminate.The heater is now in  
standby mode.  
Use the MODE  
button to select the  
desired heat setting.The mode button  
allows you to scroll through the various  
heating modes.  
Using the Remote Control  
Your heater may be operated using  
either the control panel or the remote  
control.  
The remote control uses 2 x AAA  
batteries.To access the battery  
compartment, simply remove the  
cover at the rear of the remote  
control.  
HIGH – High heat setting (1800 watts)  
LOW – Low heat setting (900 watts)  
AUTO – for use with the electronic  
thermostat  
FAN – for fan only operation  
To switch the heater into standby  
mode, press the On/Off  
button.  
To operate, ensure that you point  
the remote control at the heater.An  
audible beep will sound with the press  
of each button.  
Turn the heater off by switching the  
Power switch located on the right  
hand side of the base, to the off  
position.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd  
8
12/10/09 2:26 PM  
The temperature can be set between  
15° C and 35°C.  
NOTE: This heater features a  
tip-over switch. If the heater  
tips over, it will automatically  
switch off. Once placed back  
into the upright position, the  
heater will be in standby mode,  
and the settings will need to be  
selected again.  
When the air temperature reaches  
2-3°C above the set temperature,  
the heater will automatically cut out,  
although the fan will continue to run  
for approximately 15 seconds to cool  
the heater.  
When the air temperature drops  
below the set temperature the unit will  
begin heating again.  
Setting the Variable  
Temperature  
Setting the Oscillation  
The oscillation function works in all  
operating modes.  
The variable temperature can  
be used to maintain your desired  
temperature.  
Press the SWING  
button once to  
activate.The heater will begin to  
oscillate from side to side.  
NOTE: The variable  
Press the SWING  
button again to  
temperature only operates  
when the heater is being used  
in the Auto mode.  
stop the heater from oscillating.  
Setting the Auto-Off Timer  
The timer function works in all  
operating modes, and switches the  
unit off after a preset number of hours.  
Press the MODE  
button until the  
heater is set to AUTO mode.  
The LCD screen will display the default  
temperature of 25°C and will flash.  
When the temperature is flashing,  
you may set the desired temperature  
Press the TIMER  
button to activate  
the timer settings.A timer symbol  
will appear on the LCD screen  
displaying 1 hour.  
using the VARIABLE TEMPERATURE  
R
Press the TIMER  
button to cycle  
DIAL on top of the unit.  
through the one hour increments, up  
to 8 hours.The unit will then switch  
itself to standby mode after the  
To adjust the set temperature rotate  
the VARIABLE TEMPERATURE  
DIAL  
R
clockwise to increase the desired  
temperature or anti-clockwise to  
decrease the desired temperature.  
selected number of hours has passed.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd  
9
12/10/09 2:26 PM  
Using Your Ceramic Tower Heater  
continued  
Safety Features  
This heater includes an audible alarm  
to warn that parts of the heater are  
overheating. If the alarm sounds,  
immediately turn the heater off and  
inspect for any objects on or adjacent  
to the heater that may cause high  
temperature. DO NOT OPERATE THE  
HEATER WITH THE ALARM SOUNDING.  
ThermoGuard Overheating  
Safety Device  
Your heater is fitted with a safety  
device that switches off the heater  
in the event of overheating. Should  
this heater stop working, turn off the  
heater and inspect the air inlet and  
outlet for blockages.Wait until the  
unit is fully cooled for the protection  
system to reset before attempting to  
restart the heater.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd 10  
12/10/09 2:26 PM  
Care and Cleaning  
Ensure that the heater is switched off  
and disconnected from the power  
point before cleaning.  
Use a clean, dry cloth to clean the  
external surfaces of the heater. If  
the heater has collected dust or dirt  
inside the unit or around the elements,  
have the unit cleaned by a qualified  
service agent. Do not operate the  
heater in this condition.  
Do not attempt to open the case of  
the heater at any time as there are no  
customer serviceable parts inside.  
When not in use, store the heater  
(preferably in its original box) in a cool,  
clean and dry location.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd 11  
12/10/09 2:26 PM  
Kambrook 12 Month Replacement Warranty  
In Australia, this Kambrook Replacement Warranty  
The Kambrook Replacement Warranty does not  
apply to any defect, deterioration, loss, injury or  
damage occasioned by, or as a result of, misuse  
or abuse, negligent handling or if the product has  
been used other than in accordance with the  
instructions.The Kambrook Replacement Warranty  
excludes breakables such as glass and ceramic  
items, consumable items and normal wear and  
tear.  
does not affect the mandatory statutory rights  
implied under the Trade Practices Act 1974  
and other similar State and Territory legislation  
relating to the appliance. It applies in addition  
to the conditions and warranties implied by that  
legislation.  
In New Zealand, this Kambrook Replacement  
Warranty does not affect your mandatory statutory  
rights implied under the Consumer Guarantees  
Act 1993 in relation to the appliance. It applies in  
This Kambrook Replacement Warranty is void if  
there is evidence of the product being tampered  
addition to the conditions and guarantees implied with by unauthorised persons.  
by that legislation.  
If the product includes one or a number of  
This Kambrook Replacement Warranty is valid only accessories only the defective accessory or  
in the country of purchase, but other statutory  
warranties may still apply.  
product will be replaced. Subject to your statutory  
rights, in the event of Kambrook choosing  
to replace the appliance, the Kambrook  
Replacement Warranty will expire at the original  
date, i.e. 12 months from the original date of  
purchase.  
This Warranty card and the purchase receipt for this  
product are to be retained as proof of purchase  
and must be presented if making a claim under  
the Kambrook Replacement Warranty. Please note  
that under any applicable statutory warranty you  
In the event that you need some assistance  
are not required to produce these documents, but with your Kambrook appliance, please contact  
may be required to provide a proof of purchase.  
our Customer Service Department on 1300 139  
798 (Australia) or 09 271 3980 (New Zealand).  
Alternatively, visit us on the website at  
www.kambrook.com.au  
Kambrook warrants the purchaser against defects  
in workmanship and material for a period of 12  
months domestic use from the date of purchase  
(or 3 months commercial use).  
Kambrook 12 Month Replacement Warranty  
Your Purchase Record (Please Complete)  
Attach a copy of the purchase receipt  
here.  
Date Of Purchase ________________________________  
Model Number ___________________________________  
Serial Number ____________________________________  
Purchased From __________________________________  
(Please don’t return purchase record  
until you are making a claim)  
Kambrook - New Zealand  
Private Bag 94411  
Botany, Manukau  
Auckland 2141  
New Zealand  
Customer Service Line/Spare Parts  
0800 273 845 or 09 271 3980  
Kambrook - Australia  
Building 2, Port Air Industrial Estate  
1A Hale Street  
Botany NSW 2019  
Australia  
Customer Service Line 1300 139 798  
Customer Service Fax 1800 621 337  
Customer Service Fax 0800 288 513  
Due to continual improvement in design or otherwise, the product you  
purchase may differ slightly from the illustration in this book. Issue 1/10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KCE440_IB_FA.indd  
1
12/10/09 2:26 PM  

Indesit Washer Dryer IWDD 7123 User Manual
Ingersoll Rand Water Pump PD05P XXX XXX B User Manual
JAI Network Card Vis 300 400 User Manual
Jensen MP3 Docking Station JiSS 100 User Manual
JVC DVD Player XV 523GD User Manual
JVC Network Card VN E4 User Manual
JVC Projection Television 1004TNH II IM User Manual
Kettler Mobility Scooter 8452 200 User Manual
Keys Fitness Home Gym KF CR User Manual
KitchenAid Trash Compactor 403 User Manual