COMPACT COMPONENT SYSTEM
SYSTEME DE COMPOSANTS COMPACT
FS-X5
Consists of CA-FSX5 and SP-FSX5
Se compose de CA-FSX5 et de SP-FSX5
CA-FSX5
SP-FSX5
SP-FSX5
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT1041-001B
[C]
Download from Www.Somanuals.com. All Manuals Search And Download.
For Canada/pour le Canada
For Canada/pour Le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
THIS DIGITAL APPARATUS DOES NOT EXCEED THE
CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM
DIGITAL APPARATUS AS SET OUT IN THE INTERFER-
ENCE-CAUSING EQUIPMENT STANDARD ENTITLED “DIG-
ITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF
COMMUNICATIONS.
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
PRECAUTION: POUR EVITER LES CHOCS ELEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA
PRISE ET POUSSER JUSQUAU FOND
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAR-
EILS NUMERIQUES DE CLASSE B PRESCRITES DANS LA
NORME SUR LE MATERIEL BROUILLEUR: “APPAREILS
NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE
DES COMMUNICATIONS.
1. CLASS 1 LASER PRODUCT
1. PRODUIT LASER CLASSE 1
2. CAUTION: Invisible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user ser-
viceable parts inside the unit; leave all servicing to qualitied
service personnel.
2. ATTENTION: Radiation laser invisible quand l’appareil est
ouvert ou que le verrouillage est en panne ou désactivé.
Eviter une exposition directe au rayon.
3. ATTENTION: Ne pas ouvrir le couvercle du dessus. Iln’y a
aucune pièce utilisable à l’intérier. Laisser à un personnel
qualifié le soin de réparer votre appareil.
CAUTION
ATTENTION
To reduce the risk of electrical shocks, fire, etc.:
1 Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Afin d’èviter tout risque d’électrocution, d’lncendie. etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
Caution —STANDBY/ON
Disconnect the main plug to shut the power off completely.
The STANDBY/ON button in any position does not dis-
button!
Attention — Touche STANDBY/ON
Déconnecter la fiche de secteur poru couper complètement le
courant. La touche STANDBY/ON
ne coupe jamais com-
connect the main line. The power can be remote controlled.
• When the unit is on standby, the STANDBY/ON indicator
lights red.
• When the unit is turned on, the STANDBY/ON indicator
lights green.
plètement la ligne de secteur, quelle que soit sa position. Le
courant peut être télécommandé.
• Quand l’appareil est en mode de veillle, le tèmoin
STANDBY/ON est allumè en rouge.
• Quand l’appareil est sous tension, le tèmoin STANDBY/ON
est allumè en vert.
CAUTION
ATTENTION
1. Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by
a newspaper or cloth, etc., the heat may not be
able to get out.)
1. Ne bloquez pas les orifices ou les trous de ventila-
tion. (Si les orifices ou les trous de ventilation sont
bloqués par un journal un tissu, etc., la chaleur
pent ne pas être évacuée correctement de l’appa-
reil.)
2. Do not place any naked flame sources, such as
lighted candles, on the apparatus.
3. When discarding batteries, environmental prob-
lems must be considered and local rules or laws
governing the disposal of these batteries must be
followed strictly.
4. Do not expose this apparatus to rain, moisture,
dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the
apparatus.
2. Ne placez aucune source de flamme nue, telle
qu’une bougie, sur l’appareil.
3. Lors de la mise au rebut des piles, veuillez prendre
en considération les problèmes de l’environnement
et suivre strictement les règles et, les lois locales
sur la mise au rebut des piles.
4. N’exposez pas cet appareil à la pluie, à l’humidité,
à un égouttement ou à des éclaboussures et ne
placez pas des objets remplis de liquide, tels qu’un
vase, sur l’appareil.
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
ATTENTION
I About the Internal Cooling Fan
I A propos du ventilateur de refroidissement interne
Cet appareil est équipé d’un ventilateur de refroidissement
interne afin de permettre un fonctionnement à haute puis-
sance dans un espace limité.
This unit includes an internal cooling fan, so as to allow for
high-power operation within a small space.
This fan comes on when the sound level is set high, and may
also come on even at low sound levels if the internal temper-
ature rises. To ensure effective fan operation, please leave
at least 15cm (5-15/16”) clearance between the rear of the
unit and the wall, and at least 1cm (7/16”) clearance on each
side of the unit.
Ce ventilateur se met en marche quand le niveau sonore est
élevé et peut aussi se déclencher même à un niveau bas si
la température interne augmente. Pour garantir un fonction-
nement effectif du ventilateur, veuillez laisser un espace
libre de 15 cm au moins entre l’arrière de l’appareil et le mur,
et de 1 cm au moins de chaque côté de l’appareil.
Caution: Proper Ventilation
Attention: Aération correcte
To avoid risk of electric shock and fire, and to prevent damage,
locate the apparatus as follows:
1 Front:
Pour prévenir tout risque de décharge électrique ou d’incendie
et éviter toute détérioration, installez l’appareil de la manière
suivante:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by
the dimensions below.
3 Bottom:
1 Avant:
Bien dégagé de tout objet.
2 Côtés/dessus/dessous:
Assurez-vous que rien ne bloque les espaces indiqués sur
le schéma ci-dessous.
Place on the level surface. Maintain an adequate air path
for ventilation by placing on a stand with a height of 10 cm
(3-15/16”) or more.
3 Dessous:
Posez l’appareil sur une surface plane et horizontale.
Veillez à ce que sa ventilation correcte puisse se faire en le
plaçant sur un support d’au moins dix centimètres de hau-
teur.
Front view
Face
Side view
Côté
CA-FSX5
CA-FSX5
SP-FSX5
SP-FSX5
G-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction ........................................................................................................2
Features ......................................................................................................................................2
How This Manual Is Organized .................................................................................................2
WARNINGS ..............................................................................................................................2
IMPORTANT CAUTIONS .......................................................................................................2
Getting Started...................................................................................................3
Accessories.................................................................................................................................3
How To Put Batteries In the Remote Control ............................................................................3
Using the Remote Control..........................................................................................................3
Connecting the FM Antenna ......................................................................................................4
Connecting the AM Antenna......................................................................................................5
Connecting the Speakers (SP-FSX5) .........................................................................................6
Connecting an External Equipment............................................................................................7
Connecting an MD Recorder, etc (Optical Digital Output) .......................................................7
COMPU PLAY ..........................................................................................................................7
Automatic Power On..................................................................................................................7
Basic Operations ...............................................................................................8
Turning the Power On and Off...................................................................................................8
Changing the Source ..................................................................................................................8
Adjusting the Brightness (DIMMER - at Power On).................................................................9
Power Saving Mode (DIMMER - at Power Off).......................................................................9
Adjusting the Volume ................................................................................................................9
Fade-out Muting (FADE MUTING)..........................................................................................9
Reinforcing the Bass Sound (Active Hyper Bass Pro.)..............................................................9
Tone Control (BASS/TREBLE)...............................................................................................10
Auto Power Off (A.P.off).........................................................................................................10
Entering the Number with the Remote Control (Numeric Keys).............................................10
Using the Tuner................................................................................................11
Tuning In a Station...................................................................................................................11
Presetting Stations....................................................................................................................12
To Change the FM Reception Mode........................................................................................12
Beat Cut (AM Reception) ........................................................................................................12
Using the CD Player.........................................................................................13
To Insert a CD..........................................................................................................................13
To Unload a CD .......................................................................................................................14
Basics of Using the CD Player – Normal Play.........................................................................14
Programming the Playing Order of the Tracks – Program Play ..............................................14
Random Play ............................................................................................................................15
Repeating Tracks......................................................................................................................16
CD DOOR LOCK ....................................................................................................................16
Using External Equipments ............................................................................17
Listening to External Equipment..............................................................................................17
Changing the Equipment’s Name ............................................................................................17
Recording the System’s Source to External Equipment ..........................................................18
Adjusting the Input Level.........................................................................................................18
Using the Timers..............................................................................................19
Setting the Clock......................................................................................................................19
Showing the Clock (DISPLAY)...............................................................................................20
Correcting the Clock ................................................................................................................20
Setting the Daily Timer............................................................................................................20
Setting the SLEEP Timer.........................................................................................................23
Timer Priority...........................................................................................................................23
Troubleshooting...............................................................................................24
Care And Maintenance ....................................................................................25
Specifications...................................................................................................26
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing the JVC Compact Component System.
We hope it will be a valued addition to your home, giving you years of enjoyment.
Be sure to read this instruction manual carefully before operating your new stereo system.
In it you will find all the information you need to set up and use the system.
If you have a query that is not answered by the manual, please contact your dealer.
Features
Here are some of the things that make your System both powerful and simple to use.
❑
The controls and operations have been redesigned to make them very easy to use, freeing you to
just enjoy the music.
• With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio or
CD Player with a single touch.
❑
The System incorporates AHB (Active Hyper Bass) PRO circuitry to faithfully reproduce low
frequency sound.
❑
❑
❑
A 45-station preset capability (30 FM and 15 AM) in addition to auto-seek and manual tuning.
CD options that include repeat, random and program play.
Timer functions; Daily Timer and Sleep Timer. The Daily Timer can select one of 10 melodies as a source, in addition to
CD, FM, AM and LINE.
❑
❑
❑
You can connect various external units, such as an MD recorder.
The system can play CD-R and CD-RW after they have been finalized.
You can play back your original CD-R or CD-RW recorded in Music CD format. (However they may not be played back
depending on their characteristics or recording conditions.)
How This Manual Is Organized
• Basic information that is the same for many different functions - e.g. setting the volume - is given in the section
‘Basic Operations’, and not repeated under each function.
• The names of buttons/controls and display messages are written in all capital letters: e.g. FM/AM, “CD NO DISC”.
• System functions are written with an initial capital letter only: e.g. Normal Play.
Use the table of contents to look up specific information you require.
We have enjoyed making this manual for you, and hope it serves you in enjoying the many features built into your System.
WARNINGS
• DO NOT PUT ANYTHING ON THE CD DOOR. IF THE SYSTEM IS OPERATED WITH
SOMETHING PUT ON THE CD DOOR, IT WILL BE DAMAGED WHEN YOU TRY TO
OPEN THE CD DOOR.
• NEVER REMOVE THE CD DOOR FROM THE UNIT. SERIOUS INJURY MAY OCCUR IF
THE SYSTEM IS OPERATED WITHOUT THE CD DOOR.
IMPORTANT CAUTIONS
Installation of the System
1
• Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C or 41°F and 95°F.)
• Leave sufficient distance between the System and a TV.
• Do not use the System in a place subject to vibrations.
Power cord
• Do not handle the power cord with wet hands!
2
• Some power is always consumed as long as the power cord is connected to the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
Malfunctions, etc.
3
• There are no users serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.
• Do not insert any metallic object into the System.
• Do not insert your hand between the CD door and the main body when the CD door is being closed.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Accessories
Make sure that you have all of the following items, which are supplied with the System.
FM Wire Antenna (1)
AM Loop Antenna (1)
Remote Control (1)
Batteries (2)
Speaker Cords (4)
If any of these items are missing, contact your dealer immediately.
How To Put Batteries In the Remote Control
Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.
R6P(SUM-3)/AA(15F)
CAUTION:
• Handle batteries properly.
❑
To avoid battery leakage or explosion:
• Remove batteries when the Remote Control will not be used for a long time.
• When you need to replace the batteries, replace both batteries at the same time with new ones.
• Do not use an old battery with a new one.
• Do not use different types of batteries together.
Using the Remote Control
The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7m away.
You need to point the Remote Control at the remote sensor on the System’s front panel.
Remote Sensor
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
CAUTION:
• Make all connections before plugging the System into an AC power outlet.
Connecting the FM Antenna
Rear Panel of the Center Unit (CA-FSX5)
(on the side panel)
If reception is poor, connect the outdoor antenna.
Using the Supplied Wire Antenna
Using the Coaxial Type Connector
(Not Supplied)
A 75-ohm antenna with coaxial type connector should be
connected to the FM 75-ohm COAXIAL terminal.
FM wire antenna (supplied)
FM outdoor
antenna
(Not supplied)
• Fasten it up in the position until you have the best
reception.
Coaxial cable
• Before attaching a 75 ohm coaxial lead (the kind with a
round wire going to an outdoor antenna), disconnect the
supplied FM Wire Antenna.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Connecting the AM Antenna
FSX5)
Rear Panel of the Center Unit (CA-
AM loop antenna (Supplied)
Outdoor single vinyl-covered wire (not supplied)
Turn the loop until you have the best reception.
Attach the AM loop to its base by snapping the tabs on
the loop into the slot in the base.
• If the AM loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram.
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord.
This could cause poor reception.
• If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM loop
antenna connected.)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Connecting the Speakers (SP-FSX5)
These speakers are exclusively for this system. Using with other devices will damage the speakers.
Connect the speaker cords between the speaker terminals of the Unit and those of the Speakers.
• When inserting the speaker wire lead, open the speaker terminal.
• Connect each speaker cord as shown below.
Left side (rear view)
Right side (rear view)
Black
Black
Blue
Black
Black
Blue
Blue
Blue
SPEAKER terminal description
(On the side panel)
• Since both speakers are the same, you can put either one to the right or left side.
• Do not connect other speakers to the Unit. The difference of the load impedance causes failures.
• Do not use the supplied speakers in parallel with other speakers.
CAUTIONS:
• A TV may display irregular colors if located near the speakers. If this happens, set the speak-
ers away from the TV.
• Handling the speakers
Do not hold the speaker incorrectly. Otherwise it will be damaged. Also, dropping the speaker
can cause injury, or damage to the speaker.
Good
Not Good
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Connecting an External Equipment
Connect signal cords (not supplied) between the System’s LINE IN/OUT terminals and the output/input terminals of the ex-
ternal MD recorder, tape deck, etc. (For the details of connection, please refer to the user’s manual of the external equipment.)
You can then listen to the external source through the System or record the System’s CD player or tuner to the external unit.
Signal cord
(not supplied)
Pin-plug x 2
STEREO mini plug
MD recorder or tape deck
(not supplied)
STEREO mini plug
Pin-plug x 2
Signal cord
(not supplied)
Connecting an MD Recorder, etc (Optical Digital Output)
Unplug the cap and connect an optical digital cord (not supplied) between the System’s OPTICAL DIGITAL OUT terminal
and the input terminal of the MD recorder, etc.
You can record the digital output signal from the System’s CD Player to the MD recorder, etc.
Cap
Optical digital cord
(not supplied)
MD recorder, etc.
(not supplied)
COMPU PLAY
JVC’s COMPU PLAY feature lets you control the most frequently used System functions with a single touch.
With One Touch Operation you can play a CD, turn on the radio, or listen to an external equipment with a single press of the
play button for that function. One Touch Operation turns the power on for you, then starts the function you have specified. If
the System is not ready (no CD in place), the System still powers on so you can insert a CD.
How One Touch Operation works in each case is explained in the section dealing with that function.
The COMPU PLAY buttons are:
On the Remote Control
CD 3/8button
FM/AM button
LINE button
Automatic Power On
The System automatically turns on with the following operation.
• When you press the 0CD button on the Unit or the CD DOOR 0 button on the Remote Control, the System automatically
turns on and the CD door opens to allow CD setting. However, this operation does not change the source to CD.
When you press the STANDBY/ON
button to turn off the System, the CD door will be automatically closed if it is opened.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
STANDBY/ON
CD lamp
(Inside)
DISPLAY
LINE
FM/AM
CD 6
AHB PRO
BASS/TREBLE
AHB PRO
Source indicator
A.P. off
DIMMER
_
VOLUME +,
Source
selector
FADE
MUTING
_
VOLUME +,
STANDBY/ON
indicator
STANDBY/ON
PHONES
Display
Turning the Power On and Off
Changing the Source
The System has four sound sources, CD, FM, AM and
LINE. Select one of sources you want to listen.
For example, when you want to listen to the CD, select the
source “CD”.
Turning the System On
Press the STANDBY/ON
button.
The display comes on and “HELLO” is displayed once. The
STANDBY/ON indicator lights in green.
The System comes on ready to continue in the mode it was
in when the power was last turned off.
On the Unit
Turn the Source selector to Select the source you want.
Each time you turn it clockwise or counterclockwise, the
source changes as follows.
❑ For example, if the last thing you were doing was listen-
ing to a CD, you are now ready to listen to a CD again. If
you wish, you can change to another source.
CD ÔFM ÔAM ÔLINE
The selected source name will appear on the display and the
Source indicator on the Unit will light up.
❑ If you were listening to the Tuner last, the Tuner comes
on playing the station it was last set to.
On the Remote Control
Turning the System Off
CD
:Press the CD 6button to select the source “CD”.
Press the STANDBY/ON
button again.
You can listen to the CD. If a CD is inserted, the CD
will be played back.
“SEE YOU” is displayed and the display goes out, except for
the clock display. The STANDBY/ON indicator lights in red.
FM/AM
:Press the FM/AM button to select the source “FM” or
“AM”.
❑ Some power is always consumed even though power is
turned off (called Standby Mode).
You can listen to the FM or AM broadcast.
LINE
❑ To switch off the System completely, unplug the AC
power cord from the wall outlet. When you unplug the
AC power cord, the clock will be reset to AM 12:00.
:Press the LINE button to select the source “LINE”.
You can listen to the music through external equip-
ment.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
CAUTION:
Adjusting the Brightness
(DIMMER - at Power On)
• DO NOT turn off the System with the volu-
me set to an extremely high level; otherwi-
se a sudden blast of sound could damage
your hearing, speakers and/or headphones
when you turn on the System or start play-
ing any source next time.
You can adjust the brightness of the display.
When the System is Turned On
At power on, each time you press the DIMMER button on
the Remote Control, the brightness changes as follows:
DIMMER OFF =DIMMER 1 =DIMMER 2 =(back to
the beginning)
REMEMBER you cannot adjust the volume
level while the System is in standby mode.
DIMMER OFF: Bright
DIMMER 1 : Dark (CD lamp also becomes dark.)
DIMMER 2 : Darker (CD lamp goes out.)
Fade-out Muting (FADE MUTING)
You can mute the output with one touch operation.
Power Saving Mode
To mute the output, press the FADE MUTING button
on the Remote Control. Then, “FADE MUTING” blinks
and the output will be faded out and becomes 0.
(DIMMER - at Power Off)
In power saving mode, you can save the power while the
System is turned off (Standby Mode).
Each time you press the DIMMER button on the Remote
Control at power off, the display alternates as follows.
DISPLAY ON ÔDISPLAY OFF
To release muting, press the FADE MUTING button once
again. Then, the output will be faded in to the original level.
To enable Power Saving mode, set to “DISPLAY
OFF”.
The display completely turns off to save the power.
To restore normal power mode, reset to “DISPLAY ON”.
The Clock indicator
(
)
and the clock appear on the display.
• Adjusting the volume causes the muting process (fading
out to 0) to release.
• If you use the AHB PRO button or the BASS/TREBLE but-
ton during muting, the FADE MUTING button does not
work to release muting. In this case, turn the VOLUME
control on the Unit or the VOLUME+/ button on the Re-
mote Control to newly set the volume.
Adjusting the Volume
Turn the VOLUME control on the Unit clockwise to in-
crease the volume or turn it counterclockwise to decrease
the volume.
_
Press the VOLUME + button on the Remote Control to in-
_
crease the volume or press the VOLUME button on the
Remote Control to decrease the volume.
Reinforcing the Bass Sound
(Active Hyper Bass Pro.)
You can reinforce the bass sound to maintain rich, full bass at
low volume. (This effect does not apply to the headphones.)
You can adjust the volume level between 0 and 50.
To get the effect, press the AHB PRO button on the Unit
or the Remote Control.
“AHB PRO ON” appears and the “BASS” indicator lights up.
To cancel the effect, press the AHB PRO button again.
“AHB PRO OFF” appears and the “BASS” indicator goes out.
For private listening
Connect a pair of headphones to the PHONES jack. No
sound comes out of the speakers.
Be sure to turn down the volume before connecting or put-
ting on headphones.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
No signal condition:
Tone Control (BASS/TREBLE)
Source CD:
CD is stopped or no CD is inserted.
You can control the tone by changing the bass (low frequen-
cy) and treble (high frequency).
When no signal condition continues, “A.P.off 20 sec” (20
seconds left before elapsed time reaches three minutes) ap-
pears on the display. The displayed time is counted down
and, finally, the System is turned off (Standby mode).
• If a CD is played back, the “A.P.off” indicator stops
blinking and stays lit again.
• If you press a button or turn the VOLUME control,
three-minute counting down is reset and counting down
newly restarts.
On the Remote Control
Press the BASS/TREBLE button.
1
Each time you press the button, the Tone Control mode
changes as follows.
BASS =TREBLE =Normal display =(back to the begin-
ning)
To disable the A.P.off function
When the source is “CD”, press the A.P.off button on the
Remote Control until “A.P.off STOP” appears on the dis-
play.
While “BASS” or “TREBLE” appears on
2
the display, press the VOLUME + or
-
button to adjust the bass or treble level.
You can change the level within the range of -5 to +5. (0: flat)
Then, the “A.P.off” indicator goes out.
Entering the Number with the
Remote Control (Numeric Keys)
You will use the Numeric Keys on the Remote Control to
enter numbers for presetting stations, recalling the preset
stations, selecting track number, or programming the play-
ing tracks on a CD.
Press the BASS/TREBLE button until
normal display appears.
3
How to enter the number with the Numeric Keys is ex-
plained here.
Waiting for five seconds will also return the System to
the normal display.
Examples:
• To enter number 5, press 5.
• To enter number 10, press 10.
Auto Power Off (A.P.off)
• To enter number 15, press +10 then 5.
• To enter number 20, press +10 then 10.
• To enter number 25, press +10, +10, then 5.
You can automatically turn off the System when no signal
condition continues for three minutes. This function is ef-
fective when the source is set to “CD”, but not to “FM”,
“AM” or “LINE”.
To Enable the A.P.off function
(When the source is “CD”)
Press the A.P.off button on the Remote
Control until “A.P.off SET” appears on
the display.
1
Then, the “A.P.off” indicator lights up on the display.
• Each time you press the button, the display alternates
as follows.
A.P.off SET ÔA.P.off STOP
When no signal condition is detected, the “A.P.off” indica-
tor will start blinking soon.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
Numeric
Keys
5
3
∞
SET
2
FM/AM
FM/PLAY MODE
Multi-control
button
Source
selector
¢
4
FM mode indicator
Band display, Preset channel,
Frequency display
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
You can listen to FM and AM stations. Stations can be
tuned in manually, automatically, or from preset memory
storage.
Select a station using one of the follow-
ing methods.
2
G Manual Tuning
❑ Before listening to the radio:
Press the ¢or 4button on the Unit or the 5 or
∞ button on the Remote Control repeatedly to move
from frequency to frequency until you find the station
you want.
• Make sure that both the FM and AM antennas are cor-
rectly connected. (See pages 4 and 5).
One Touch Radio
Just press the FM/AM button on the Remote Control to turn
on the System and start playing the station you were last
tuned to.
OR
G Auto Tuning
If you press and hold the ¢ or 4 button on the
Unit or the 5 or ∞ button on the Remote Control
for one second or more, the frequency changes up, or
down, automatically until a station is found.
❑ You can switch from any other sound source to the radio
by pressing the FM/AM button.
OR
Tuning In a Station
G Preset Tuning using the Remote Control
(Possible only after presetting stations)
Select the desired preset number using the 3 or 2
button on the Remote Control. The display will show
the preset number’s band and frequency.
• You can also select the desired preset number
using the Numeric Keys. See “Entering the
Number with the Remote Control” on page 10.
(e.g. Press +10, and then 2 for number 12.)
Press the FM/AM button.
The Band and Frequency you were last tuned to appear
on the display.
1
(If the last station was selected using the preset number,
the preset number appears first.)
Each time you press the button, the band alternates be-
tween FM and AM.
• You can also select the band by turning the Source
selector on the Unit.
Example:
Press the 3 button until the preset number “2” ap-
pears.
Preset number
UP
DOWN
3
3
or
(On the Remote Control)
(On the Unit)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
CAUTION:
Presetting Stations
• Even if the system is unplugged or if the
power failure occurs, the preset stations
will be stored for about 24 hours. However,
in case the preset stations are erased, you
will need to preset the stations again.
You can preset up to 30 FM stations and up to 15 AM sta-
tions.
• Preset numbers may have been set to factory test fre-
quencies prior to shipment. This is not a malfunction. You
can preset the stations you want into memory by following
one of the presetting methods below.
To Change the FM Reception
Mode
When you are tuned into an FM stereo broadcast, the “ST.”
indicator lights up and you can hear stereo effects.
If an FM stereo broadcast is hard to receive or noisy, you
can select Monaural mode. Reception improves, but you
lose stereo effect.
FM AUTO mode is also useful to suppress static noise be-
tween stations.
1
STORED
SET
FM/AM
SET
+10
2
or
FM = 30, AM = 15
When changing the Band
To enter Monaural mode while receiving an FM
broadcast, press the FM/PLAY MODE button on the Re-
mote Control until “FM MONO” appears on the display. Then,
the “MONO” indicator lights up.
On the Remote Control
Each time you press the FM/PLAY MODE button, the display
Select a band by pressing the FM/AM
button.
1
2
3
alternates between “FM AUTO” and “FM MONO”.
FM/PLAY
MODE
5 ∞
Press the or button to tune in a sta-
tion.
FM AUTO ÔFM MONO
Press the SET button.
To restore the stereo effect, press the FM/PLAY
MODE button on the Remote Control until “FM AUTO” ap-
pears on the display. Then, the “MONO” indicator goes out
and the “ST.” indicator will light up.
Preset number “1” will blink for 5 seconds.
Within 5 seconds, proceed to the next step.
When the display returns to the one set in step 2 after 5
seconds, press the SET button again.
3 2
Press the Numeric Keys, or the or
4
Beat Cut (AM Reception)
button within 5 seconds to select the
preset number.
Switching the Beat Cut mode may reduce beat noise.
Each time you press the FM/PLAY MODE button while re-
ceiving an AM broadcast, the Beat Cut mode changes as fol-
lows.
Example:
BEAT CUT 1 =BEAT CUT 2 =BEAT CUT 3 =
BEAT CUT 4 =(back to the beginning)
FM/PLAY
MODE
Press the SET button within 5 seconds.
“STORED” appears and after 2 seconds, the display re-
turns to the broadcast frequency display.
5
6
Set to the position where beat noise is small.
• The best position will differ depending on the AM
broadcast station being received.
Repeat above steps 1 to 5 for each sta-
tion you want to store in memory with a
preset number.
• In AM broadcast, reception sensitivity will be changed by
turning the AM loop antenna. Turn the AM loop antenna
for best reception.
To change the preset stations, repeat the same
steps as above.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
Numeric
Keys
CD DOOR 0
CANCEL
5
3
∞
SET
2
CD door
CD 6
7
REPEAT
FM/PLAY MODE
0CD
6
Source
selector
¢
7
Disc
indicator
4
Repeat indicator
Play mode
indicator
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
You can use Normal, Random, Program or Repeat Play. Re-
peat Play can repeat all the tracks or just one of the tracks
on the CD.
To Insert a CD
Here are the basic things you need to know to play a CD and
locate the different tracks on it.
Select the source “CD” using the
1
2
Source selector on the Unit.
This Unit has been designed only to playback the follow-
ing CDs.
• Digital audio CD
• Recordable digital audio CD (CD-R)
• Rewritable digital audio CD (CD-RW)
0
Press the CD button on the Unit or
0
the CD DOOR button on the Remote
Control.
The CD door opens.
Place a CD, with its label side up as
shown below. Press down on the CD’s
center until you hear a click.
3
When playing a CD-R or CD-RW
You can play back finalized CD-R or CD-RW recorded
music CD format. (If CD-RW have been recorded in a
different format, erase all the data on CD-RW complete-
ly before recording on the disc.)
❑ You can play back CD-R or CD-RW like CD.
❑ Some CD-R or CD-RW may not be played back on
this Unit because of their disc characteristics, damage
or stain on them, or if the player lens is dirty.
❑ The reflection factor of CD-RW is lower than that of
other CD, possibly causing CD-RW to take longer to
read.
❑ CD-R and CD-RW of MP3 format are not played
0
Press the CD button on the Unit or the
4
back.
0
CD DOOR button on the Remote Con-
The Quickest Way To Start a CD Is With the One
Touch Operation
trol again to close the CD door.
“CD DOOR CLOSE” appears and then, “CD READ-
ING” appears on the display. At that time, Disc indica-
tor ( ) will also be lit on the display.
• To close the CD door and play the CD, you can just
press the 6button on the Unit or the CD 6but-
ton on the Remote Control.
❑ Press the CD 6button on the Remote Control.
• The power is automatically turned on and, if a CD is
already inserted, it will start playing from the first track.
• If no CD is inserted, “CD NO DISC” appears on the dis-
play and the CD Player remains in Stop mode.
❑ You can place an 8 cm CD without an adaptor.
❑ If the CD cannot be read correctly (because it is scratch-
ed, for example), “CD CAN’T PLAY” appears on the
display.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
❑ You can insert a CD while listening to the other source.
• However, while the CD door is operating (opening or
closing), the other source will be muted.
To Select a Track or Passage within a Track
During playback
Press the ¢or 4button on the Unit or the 3or 2but-
ton on the Remote Control to select the track you want.
• The selected track starts playing.
CAUTION:
• DO NOT try to open or close the CD door by
• Press the ¢(or 3) button once to skip to the
beginning of the next track.
• Press the 4(or 2) button to skip to the beginning
of the track being played. Press twice quickly to skip
to the beginning of the previous track.
• When the 3or 2button on the Remote Control is
kept pressing, the track continuously skips.
• Press the Numeric Keys to select truck number (See
page 10).
hands as it will be damaged.
To Unload a CD
Take out the CD as shown below.
In Stop mode
• Press the ¢or 4(or 3or 2) button to skip the
track.
• Hold down the ¢or 4(or 3or 2) button to
continuously skip the tracks.
Search Play
Holding down the ¢or 4button on the Unit or the 5
or ∞button on the Remote Control, during playback, will
fast forward/backwards the CD so you can quickly find a
particular passage in the track you are listening to.
Basics of Using the CD Player
– Normal Play
To Play a CD
Programming the Playing Order
of the Tracks – Program Play
Select the source “CD”.
1
Insert a CD.
2
3
You can program up to 32 tracks in any desired order in-
cluding the same tracks.
Press the 6button on the Unit or the
CD 6button on the Remote Control.
❑ You can only make a program when the CD Player is
stopped.
The first track of the CD begins playing.
On the Remote Control
Insert a CD.
1
Press the CD 6button.
2
Track number
Playback time
Press the 7button to stop the CD.
3
4
• The CD Player automatically stops when the last
track of the CD has finished playing.
Press the FM/PLAY MODE button until
“CD PROGRAM” appears.
The System enters the Program Play mode and the
“PRGM” indicator lights up.
To stop playing the CD, press the 7button.
The following information for the CD is displayed.
Each time you press the button, the play mode changes
as follows.
CD PROGRAM =CD RANDOM =CD NORMAL
=(back to the beginning)
Total track number
Total playback time
To stop playing and remove the CD, press the 0CD
button on the Unit or the CD DOOR 0 button on the Re-
mote Control to open the CD door.
(After a few seconds)
To pause, press the 6button on the Unit or the CD 6
button on the Remote Control. The playback time blinks on
the display.
To cancel pause, press the same button again. Play con-
tinues from the point where it was paused.
• If already programmed, the track number and preset
number of the last programmed track will appear.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
Press the Numeric Keys to enter the
track number you want to program (See
page 10).
The program order number will be assigned from “1”, if
nothing is programmed yet.
5
• If the total playback time of the programmed tracks ex-
ceeds 1 hour and 40 minutes, “--:--” will appear on the dis-
play.
• If you try to program the 33rd track, “MEMORY FULL” ap-
pears on the display for about 2 seconds.
Example:
Track number
Program order number
(After a few seconds)
To Modify the Program
Modify the contents of the program while the CD Player is
stopped.
Each time you press the CANCEL button, the last track in
the program is deleted. To add new tracks to the end of the
program, repeat above step 5.
Total playback time of the programmed tracks
Random Play
• To delete the last entry, press the CANCEL button.
The tracks will play in no special order when you use this
mode.
Repeat step 5 to program the other
tracks.
You can see the total playback time of programmed
tracks on the display.
6
7
In Stop mode, press the FM/PLAY MODE
button on the Remote Control until “CD
RANDOM” appears.
1
Press the CD 6button.
The System plays the tracks in the order you have pro-
grammed them.
The “RANDOM” indicator lights up on the display.
Each time you press the button, the play mode changes
as follows.
CD PROGRAM =CD RANDOM = CD NORMAL
=(back to the beginning)
The CD will stop when all of the programmed tracks
have been finished playing.
• You can also press the 6button on the Unit.
Press the CD 6button on the Remote
Control.
2
❑ You can skip to a particular program track by pressing the
3or 2button on the Remote Control or the ¢or 4
button on the Unit during Program Play.
The tracks are played in random order.
The CD will stop when all the tracks have been finished
playing.
❑ You can perform search play by holding down the ¢or
4button on the Unit or the 5or ∞button on the Re-
mote Control during playback.
• You can also press the 6button on the Unit.
To skip a track during playback, press the ¢(or 3)
button to jump to the next track in the random sequence.
Press the 4(or 2) button to jump back to the start of a
track being played.
To perform search play during playback, hold down
the ¢(or 5) or the 4(or ∞) button.
To exit the Random Play mode, while the CD Player
is stopped, press the FM/PLAY MODE button until “CD
NORMAL” appears on the display. (The “RANDOM” in-
dicator goes out.)
❑ To stop playing, press the 7button once.
To confirm the programmed tracks while the CD
player is stopped, each time you press the 3or 2but-
ton, the tracks making up the program will successively be
displayed in the programmed order.
To delete all the tracks in the program, in Stop mode,
hold down the CANCEL button until “ALL CLEAR!” ap-
pears on the display.
Opening the CD door or turning off the System will clear
the programmed tracks and release the Program Play mode.
To exit the Program Play mode once, while the CD
Player is stopped, press the FM/PLAY MODE button until
“CD NORMAL” appears on the display. (The “PRGM” in-
dicator goes out.)
To re-enter the Program Play mode, press the FM/
PLAY MODE button until “CD PROGRAM” appears on
the display. (The “PRGM” indicator lights up.)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
Repeating Tracks
CD DOOR LOCK
You can repeat all tracks or individual track, as many times
as you like.
You can prevent unwanted CD ejection by locking the CD
door. The CD Player works normally except CD ejection
operation.
During playback or in Stop mode, press the RE-
PEAT button on the Remote Control.
Each time you press the button, the Repeat mode and Re-
peat indicator change as follows.
Locking the CD door
Turn off the system.
1
CD REPEAT ALL (
ALL) =CD REPEAT 1 (
)
While pressing down the 7button on
the Unit, press the 0CD button on the
Unit.
=CD REPEAT OFF =(back to the beginning)
2
ALL: In Normal Play mode, repeats all the tracks.
In Program Play mode, repeats all the tracks
in the program.
“DOOR LOCKED” appears on the display.
In Random Play mode, repeats all the tracks
in random order.
:
Repeats one track.
• If you try to open the CD door, “DOOR LOCKED”
appears on the display to let you know that the CD
door has been locked.
To exit the Repeat mode, press the REPEAT button un-
til “CD REPEAT OFF” appears and the Repeat indicator on
the display goes out.
Unlocking the CD door
Repeat above steps 1 and 2.
❑ Repeat mode remains in effect even when you change the
play mode.
“DOOR UNLOCKED” appears on the display.
Now, you can open the CD door normally.
• Even after the System is unplugged, the CD door lock
condition will be retained for about 24 hours. To unlock the
CD door after powering up, you need to perform the un-
locking operation.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using External Equipments
SET
2
3
LINE
Source
selector
Listening to External
Equipment
Changing the Equipment’s Name
You can change the equipment’s name according to the
equipment to be used. (At purchase, “LINE” is selected.)
You can listen to the external equipment such as MD re-
corder, tape deck or other auxiliary.
On the Remote Control
❑ First make sure that the external equipment is properly
connected to the System. (See page 7).
Press the LINE button to select the
source “LINE”.
1
Set the VOLUME control to the mini-
mum position.
1
Press the LINE button for two seconds
or more.
2
Press the LINE button on the Remote
Control.
2
“NAME CHANGE” blinks on the display.
“LINE” will appear on the display.
While “NAME CHANGE” is blinking,
press the SET button.
3
• You can also select “LINE” using the Source Selec-
tor on the Unit.
Start playing the external equipment.
Press the 3or 2button repeatedly to
select the desired name.
Each time you press the button, the equipment name
changes as follows.
3
4
4
Adjust the VOLUME control to the
desired listening level.
LINE Ô TAPE Ô DBS Ô VCR Ô TVÔ
GAME Ô (back to the beginning)
DBS (Direct Broadcasting Satellite): For CS/BS
Apply the following sound effects, if you
wish.
5
• AHB PRO (See page 9.)
Press the SET button
The current name is replaced with new one.
(When TAPE is selected)
5
• Tone (BASS/TREBLE) (See page 10.)
To exit the source “LINE”, select other source (e.g.
CD).
• For operation of the external equipment, refer to its In-
structions.
• The selected name will appear on the display when you
select the source “LINE”.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using External Equipments
Recording the System’s Source
Adjusting the Input Level
to External Equipment
If the sound from the component connected to the LINE IN
jacks is too loud or is not loud enough when changing the
source to the external component (without adjusting the
volume level), you can change the input level through the
LINE IN jacks.
You can record the System’s source to external equipment
which is connected to the LINE OUT or OPTICAL DIGI-
TAL OUT terminal of the System, such as tape deck or MD
recorder, etc.
❑ First make sure that the external equipment is properly
connected to the System. (See page 7).
On the Remote Control
When the source is “LINE”, press and
hold the SET button.
1
❑ When recording an FM or AM program, use the LINE
OUT terminal (not the OPTICAL DIGITAL OUT termi-
nal).
Play the System’s CD Player or tune in
to a station.
1
❑ The recording level is not affected by the VOLUME level
set by the System. Also it is not affected by the sound ef-
fects.
• If you have changed the source name of the external
component, the currently selected source will appear
(see page 17).
Press the 3or 2button to select an
appropriate input level.
2
• For operation of the external equipment, refer to its In-
structions.
• Each time you press the button, the input level alter-
nate between “INPUT LEVEL1” and “INPUT
LEVEL2”.
INPUT LEVEL1: Select this when the sound is not loud
enough.
INPUT LEVEL2: Select this when the sound is too loud.
Press the SET button to finish the
adjustment.
3
• “LEVEL2 STORED” appears on the display.
• The selected input level will be kept in memory until
you change it.
The input level is too high.
• Select “INPUT LEVEL2” if the current level is “INPUT
LEVEL1”.
• If the current level is “INPUT LEVEL2”, adjust the output
level on the external component.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
STANDBY/ON
CANCEL
SET
3
2
CLOCK/TIMER
SLEEP
DAILY indicator
Clock indicator
SLEEP indicator
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
The timers let you control listening functions automatically.
Two types of timers are available:
On the Remote Control
DAILY Timer
Press the CLOCK/TIMER button.
The hour digit of the time indication blinks on the dis-
play, also, the Clock indicator ( ) blinks.
1
Use this timer to set wake up everyday to music from
any source, including melodies.
SLEEP Timer
Fall asleep and have your System turn off automatically
after a certain length of time.
Setting the Clock
When you plug the AC power cord into the wall outlet, the
time indication “AM12:00” and the Clock indicator (
)
• If the clock is already set and the Clock indicator (
) is
blink on the display in standby (System off) mode.
You can set the clock whether the System is on or off (but
not in power saving mode (See page 9)).
not blinking, press the CLOCK/TIMER button repeatedly
until the clock setting display appears on the display.
Each time you press the CLOCK/TIMER button, the dis-
play changes as follows.
DAILY ON?/DAILY OFF? =ON (time) =Clock setting
display* =Cancelled =(back to the beginning)
*: Select this item!
• The clock must be correctly set for the timers to work.
• The clock may gain or lose one to two minutes per month.
Press the 3or 2button to set the hour.
Pressing the 3 button moves the time forwards and
pressing the 2 button moves it backwards. Holding
down the button moves the hour.
2
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
Example:
Press the SET button.
The minute digits of the time indication blink on the dis-
3
play.
• To return to the hour setting, press the CANCEL
button.
Alternates
Press the 3or 2button to set the minute.
4
5
Press the SET button.
“ADJUST OK!” appears on the display. The Clock in-
dicator ( ) remains lit. Then, the selected time is set
and the seconds start counting from 0.
CAUTION:
• If there is a power failure, the clock loses its
setting. “AM12:00” and the Clock indicator
(clock)
Display the source
(
) blinks on the display and the clock
must be reset.
(clock is canceled)
Showing the Clock (DISPLAY)
Perform steps 2 to 5 in “Setting the Clo-
ck” on page 19-20.
2
You can show the current time on the display.
To display the clock, press the DISPLAY button on the
Remote Control.
To return to the normal display, press the same button
again.
• When the System is in power saving mode, nothing ap-
pears on the display. To see the clock, press the DIMMER
button on the Remote Control.
• The clock may gain or lose one to two minutes per month.
• If there is a power failure, the clock loses its setting,
“AM12:00” blinks on the display and the clock must be re-
set. To reset the clock, see “Setting the Clock” on page
19-20.
Correcting the Clock
Use the following method to correct any clock shift.
❑ You can correct the clock whether the System is turned
on or off.
Setting the Daily Timer
Repeatedly press the CLOCK/TIMER bu-
1
Once you have set the Daily Timer, the timer will be acti-
vated at the same time every day.
The “DAILY” indicator on the display shows that the Daily
Timer you have set is in effect.
tton to show the clock on the display.
Each time you press the button, the display changes as
follows.
You can set the Daily Timer whether the System is on or off
(but not in power saving mode (See page 9)).
• If you have made a mistake while setting the timer, press
the CANCEL button on the Romote Control. However, this
does not always cancel the current setting. If the CANCEL
button does not work, press the CLOCK/TIMER button on
the Remote Control repeatedly until the display returns to
the original display, and start from the first step.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
2. Press the 3or 2button to set the minute, then press
the SET button.
On the Remote Control
Press the CLOCK/TIMER button repeat-
edly until “ON (time)” appears on the
1
display.
At this time, “DAILY” indicator blinks on the display.
Each time you press the button, the display changes as
follows.
DAILY ON?/DAILY OFF? = ON (time)* = Clock
setting display =Cancelled =(back to the beginning)
*: Select this item!
The System enter Music Source Selecting mode and
“FM?” appears on the display.
The System enters ON-time setting mode, and the cur-
rent ON time appears on the display and the hour digits
blink.
Selecting the music source.
4
Press the 3or 2button to select the music source you
want to listen to, then press the SET button.
Each time you press the 3 or 2 button, the display
changes as shown below:
FM? ÔAM? ÔCD? ÔLINE?* Ô MELODY?
Ô(back to the beginning)
*: If the name has been changed, that name (e.g.
“TAPE”) will appear. (See page 17.)
According to the music source you have selected, the
next operation differs.
Setting the ON time (Example: AM 10:15)
.
2
1. Press the 3or 2button to set the hour you want the
System to come on, then press the SET button.
The minute digits of the ON time blink on the display.
Pressing the 3 button moves the time forwards and
pressing the 2button moves it backwards.
FM?
: Tunes in to the specified preset FM sta-
tion.
Holding down the button moves the time.
AM?
CD?
: Tunes in to the specified preset AM sta-
tion.
: Plays the specified track on the speci-
fied CD.
LINE?
: Plays an external source.
MELODY? : Select one of 10 melodies.
2. Press the 3or 2button to set the minute, then press
the SET button.
Preparation for each music source:
Perform the following operation according to the music
source you have selected. Then, the System enters Vol-
ume Setting mode.
G When selecting “FM?” or “AM?”
Press the 3 or 2 button to select the preset station
number, then press the SET button.
• If you select the display “- -”, the current broad-
cast station is selected.
The System enters OFF-time setting mode, and the
hour digits blink.
G When selecting “CD?”
Press the 3 or 2 button to select the track number
you want to start playback, then press the SET button.
• If you select the display “- -”, playback will start
from the first track.
Setting the OFF time (Example: PM 1:30).
3
G When selecting “LINE?”
Note that the same time as the ON time cannot be set.
Prepare the external equipment so that it will turn on
at the ON time set by the System.
To allow this, the equipment should have the timer
function.
1. Press the 3or 2button to set the hour you want the
System to be turned off, then press the SET button.
The minute digits of the OFF time blink on the dis-
play.
G When selecting “MELODY?”
Press the 3 or 2 button to select one of melodies
(MELODY 1-10). Then, the selected melody is
played back.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
Setting the volume level.
Press the 3 or 2 button to select the volume level
5
(VOLUME 1-50), then press the SET button.
• When a melody is set for the Daily Timer while playing
back the CD, the CD will stop playing.
• In step 4, the selected melody will be played back for your
reference. However, if the melody is selected with the Sys-
tem turned off, no melody will be heard.
• During setting the melody, the source cannot be selected
with the Source selector on the Unit or the source select
button on the Remote Control.
• If the system is already on when the timer ON-time comes,
the Daily Timer does not work.
Select the FADE function.
Press the 3or 2button to select either “FADE” (fades
in at power on) or “NoFADE” (does not fade in).
6
Press the SET button.
7
The timer setting is completed, and the “DAILY” indi-
cator stops blinking and remains lit. Each setting you
have made appears on the display in the order of ON
time, OFF time, music source, volume and fading.
Then, the display returns to the display before you set
the timer.
Turning the Daily Timer On and Off
Once you have set the Daily Timer, it is stored in memory.
So, the Daily Timer will be activated at the same time every
day until it is canceled.
To cancel the Daily Timer temporarily:
Press the STANDBY/ON
turn off the System.
button to
8
On the Remote Control
The Clock indicator ( ) and “DAILY” indicator are lit
Press the CLOCK/TIMER button repeat-
edly until the “DAILY ON?/DAILY OFF?”
1
on the display, showing that the Daily Timer is set to on.
To change the timer setting, repeat the setting proce-
dure from the beginning.
appears on the display.
The “DAILY” indicator blinks on the display.
When the timer ON-time comes:
The following operation will be automatically repeated every-
day.
Press the CANCEL button.
2
“DAILY OFF” appears and the “DAILY” indicator
goes out.
• When the timer ON-time comes, the System automati-
cally turns on. The “DAILY” indicator blinks, and then
“DAILY TIMER” and “TIMER STANDBY” alternate
for a while. After that, the music source you have set is
played. The “DAILY” indicator blinks during timer
operation. In the case of MELODY, it’s title scrolls on
the display.
• When the timer OFF-time comes, “DAILY TIMER” and
“OFF” alternate for a while. Then, the System automati-
cally turns off and the “DAILY” indicator remains lit.
To activate the canceled Daily Timer:
On the Remote Control
Press the CLOCK/TIMER button repeat-
edly until the “DAILY ON?/DAILY OFF?”
1
appears on the display.
The “DAILY” indicator blinks on the display.
Selectable Melodies
When you select the melody as the source in step 4, you can
use one of the following melodies.
MELODY 1:Twinkle Twinkle Little Star (by W.A.Mozart)
MELODY 2:Grandfather’s Clock (by H.C.Work)
MELODY 3:Csikos Post (by H.Necke)
MELODY 4:Farewell Song (by La chambre de Chopin)
MELODY 5:Canon (by J.Pachelbel)
Press the SET button.
2
The “DAILY” indicator remains lit. Each setting al-
ready made appears on the display in the order of ON
time, OFF time, music source, volume, and fading.
Then the display returns to the original display.
• “DAILY TIMER/NO SET” appears on the display
before you enter the timer setting.
MELODY 6:Menuett (by J.S.Bach)
MELODY 7:Humoresk (by A.Dvorak)
MELODY 8:Serenade (by J.Haydn)
MELODY 9:Jesus,Joy Of Man’s Desiring (by J.S.Bach)
MELODY10:Ravel’s Bolero (by Ravel)
CAUTION:
• If the System is unplugged, or a power fail-
ure occurs, the timer setting will be lost.
You will need to reset the clock first, then
the timer.
• When you select the melody as the source, only the title
of the selected melody will appear on the display.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
Setting the SLEEP Timer
Timer Priority
Use the Sleep Timer to turn the System off after a certain
number of minutes when it is playing. By setting the Sleep
Timer, you can fall asleep to music and know that your Sys-
tem will turn off by itself rather than play all night.
The timer that will turn off earlier has the priority. You will
see the priority from the following examples.
Example 1
Setting
OFF
• You can only set the Sleep Timer when the System is on.
On the Remote Control
SLEEP Timer
ON
OFF
During playback a source, press the
SLEEP button.
1
DAILY Timer
The “SLEEP” indicator lights up on the display.
PM11:00
PM10:00 PM10:30
Set the length of time you want the
source to play before shutting off.
Each time you press the SLEEP button, the time length
changes as follows:
10 =20 =30 =60 =90 =120 =OFF =(back to
the beginning)
2
Operation
OFF
SLEEP Timer
DAILY Timer
ON
Wait for a few seconds.
3
PM10:00 PM10:30
The display returns to the original one. The display is
dimmed (DIMMER 2 mode) and the CD lamp goes out.
The System is now set to turn off after the number of
minutes you have set.
Example 2
Setting
OFF
To Confirm the Sleep Time:
SLEEP Timer
DAILY Timer
When the SLEEP button is pressed, the remaining sleep
time is displayed. Wait until the display returns to the orig-
inal display.
OFF
ON
To Cancel the SLEEP Timer Setting:
Press the SLEEP button on the Remote Control until
“SLEEP OFF” appears and the “SLEEP” indicator goes out
on the display.
PM10:00 PM10:30 PM11:00
• Pressing the CLOCK/TIMER button or turning off the
System also cancels the SLEEP Timer.
Operation
SLEEP Timer
DAILY Timer
ON
• When the SLEEP button is used without setting the clock,
“CLOCK ADJUST!” appears on the display. You need to
set the clock beforehand.
OFF
PM10:00 PM10:30
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
• If you are having a problem with your System, check this list for a possible solution before calling for service.
• If you cannot solve the problem from the hints given here “ERROR!” appears on the display, or the System has been phys-
ically damaged, call a qualified person, such as your dealer, for service.
Symptom
No sound is heard.
Possible Cause
Action
• Connections are incorrect, or loose.
• Check all connections and make cor-
rections. (See pages 4 to 7.)
• Disconnect the headphones.
• Headphones are connected.
Poor radio reception
• The antenna is disconnected.
• The AM Loop Antenna is too close
to the System.
• The FM Wire Antenna is not prop-
erly extended and positioned.
• Reconnect the antenna securely.
• Change the position and direction of
the AM Loop Antenna.
• Extend FM Wire Antenna to the best
reception position.
Stereo effect is lost in FM broadcast.
The CD skips.
FM reception mode is changed to “FM Press the FM/PLAY MODE button to
MONO”.
select “FM AUTO”. (See page 12)
• The CD is dirty or scratched.
• Track Skip marks are recorded.
• Clean or replace the CD.
• This is normal.
The CD does not play.
• The CD is upside down.
• Track Skip mark is recorded for the
first track of the disc.
• Put the CD in with the label side up.
• Wait until the Unit finds a track with-
out a Track Skip mark.
Unable to operate the Remote Control.
Operations are disabled.
• The path between the Remote Con-
trol and the sensor on the Unit is
blocked.
• Remove the obstruction.
• The batteries have lost their charge.
• Replace the batteries.
The built-in microprocessor has mal- • Unplug the System then plug it back
functioned due to external electrical in-
terference.
in.
“CD NO DISC” appears.
There is no disc loaded.
Insert a disc
“CD CAN’T PLAY” appears.
• You are trying to playback a CD
which cannot be played, or there is a
problem with the CD.
• The disc has been inserted with its
label side down.
• Change the disc.
• Remove the disc and insert it with
the label side up.
“CD DOOR ERROR” appears.
The object is blocking the CD door to Press the 0CD button to close the CD
open. door and remove the object.
When the CD door is operating (open- This is one of the characteristics of this This is normal.
ing or closing) while you are listening
to FM, AM or LINE, the source is mut-
ed.
system.
Some of the CD functions, such as skip You are playing an unfinalized disc.
or search, do not work correctly.
This is normal. If you need to use these
functions, finalize the disc. (This Unit
cannot finalize CD-R/CD-RW)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Care And Maintenance
Handle your CDs carefully, and they will last a long time.
- DO NOT wipe it with a hard cloth.
- DO NOT wipe it strong.
- DO NOT wipe it with thinner or benzine.
- DO NOT apply any volatile substance such as insecti-
cides to it.
Compact Discs
- DO NOT allow any rubber or plastic to remain in con-
tact with it for a long time.
• Only CDs bearing these marks
can be used with this System.
However, continued use of irregu-
lar shape CDs (heart-shape,
octagonal, etc.) can damage the
System.
Cleaning the Lens
If the lens in the CD pickup is dirty, dropout, etc., could de-
grade sound.
Open the CD door and clean the lens as shown.
• Use a blower (available from a camera store) to blow
dust off the lens.
Blower
• Remove the CD from its case by
holding it at the edges while press-
ing the case’s center hole lightly.
• Do not touch the shiny surface of
the CD, or bend the CD.
Lens
• Put the CD back in its case after
use to prevent warping.
• Be careful not to scratch the sur-
face of the CD when placing it
back in the case.
• Avoid exposure to direct sunlight,
temperature extremes, and moisture.
• If there are fingerprints, etc. on the lens, gently wipe
clean with a cotton swab.
• A dirty CD may not play cor-
rectly. If a CD does become dirty,
wipe it with a soft cloth in a
straight line from center to edge.
CAUTION:
• Do not use any solvent (for example, con-
ventional record cleaner, spray thinner,
benzine, etc.) to clean a CD.
Moisture Condensation
General Notes
Moisture may condense on the lens
inside the System in the following
cases:
• After turning on heating in the
room.
• In a damp room.
• If the System is brought directly
from a cold to a warm place.
Should this occur, the System may
malfunction. In this case, leave the
System turned on for a few hours un-
til the moisture evaporates, unplug
the AC power cord, and then plug it
in again.
In general, you will have the best performance by keeping
your CDs and the mechanism clean.
• Store CDs in their cases, and keep them in cabinets or on
shelves.
• Keep the System’s CD door closed when not in use.
Cleaning the Unit
• Stains on the Unit
Should be wiped off with a soft cloth. If the Unit is heavily
stained, wipe it with a cloth soaked in water-diluted neutral
detergent and wrung well, then wipe clean with a dry cloth.
• Since the Unit may deteriorate in quality, become
damaged or get its paint peeled off, be careful
about the followings.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
CA-FSX5
Amplifier
Output Power
Main :60 W (30 W + 30 W) at 4 Ω (1 kHz 10% THD)
Sub :60 W (30 W + 30 W) at 4 Ω (80 Hz 10% THD)
Input Sensitivity/Impedance (1 kHz)
LINE IN :210 mV/51 kΩ (LEVEL 1)
520 mV/51 kΩ (LEVEL 2)
Output Sensitivity/Impedance (1 kHz)
LINE OUT :600 mV/5.1 kΩ
OPTICAL DIGITAL OUT :–23 dBm - –15 dBm
Speaker terminals :MIN. 4 Ω
Phones :16 Ω - 1 kΩ
CD Player
Signal-To-Noise Ratio :95 dB
Wow And Flutter :Unmeasurable
Tuner
FM Tuner
Tuning Range :87.5 MHz - 108.0 MHz
AM Tuner
Tuning Range :530 kHz - 1 710 kHz
Power Specifications
Power Requirements :AC 120 V
, 60 Hz
Power Consumption :35 W (power on mode)
1.2 W (on Standby: with display off)
4.6 W (on Standby: with display on)
Center Unit
Dimensions :160 mm ✕ 130 mm ✕ 242 mm (W/H/D)
Mass :Approx. 2.3 kg
Speaker Specifications (each unit)
SP-FSX5
Type :2way Bass-reflex type
Main-Speaker :9.5 cm ✕ 1 cm
Direct drive
Power Handling Capacity :30 W
Impedance :4 Ω
Sub-woofer :9.0 cm cone
Power Handling Capacity :30 W
Impedance :4 Ω
Sound Pressure Level :77 dB/W·m
Cross over frequency :210 Hz
Frequency Range :52 Hz
20 000 Hz
Dimensions :140 mm ✕ 301.5 mm ✕ 185 mm (W/H/D)
Mass :Approx. 2.3 kg each
Accessories
FM Wire Antenna (1)
AM Loop Antenna (1)
Remote Control (1)
Batteries (2)
Speaker Cords (4)
Design and specifications are subject to change without notice.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Caractéristiques
CA-FSX5
Amplificateur
Puissanc
Principal :60 W (30 W + 30 W) à 4 Ω (1 kHz 10% THD)
Secondaire :60 W (30 W + 30 W) à 4 Ω (80 Hz 10% THD)
Sensibilité/Impédance d’entrée (1 kHz)
LINE IN :210 mV/51 kΩ (LEVEL 1)
520 mV/51 kΩ (LEVEL 2)
Sensibilité/Impédance de sortie (1 kHz)
LINE OUT :600 mV/5,1 kΩ
OPTICAL DIGITAL OUT :–23 dBm - –15 dBm
Bornes des haut-parleurs :4 Ω min.
Casque d’écoute :16 Ω - 1 kΩ
Lecteur CD
Rapport signal/bruit :95 dB
Pleurage et scintillement :Unmeasurable
Tuner
Tuner FM
Bande de fréquence :87,5 MHz - 108,0 MHz
Tuner AM
Bande de fréquence :530 kHz - 1 710 kHz
Alimentation
Tension requise :AC 120 V
, 60 Hz
Consommation :35 W (allumé)
1,2 W (en veille : affichage éteint
)
4,6 W (en veille : affichage allumé
)
Elément central
Dimensions :160 mm ✕ 130 mm ✕ 242 mm (L/H/P)
Poids :Environ 2,3 kg
Speaker Specifications (each unit)
SP-FSX5
Type :Enceinte résonance 2-voie
Haut-parleur principal :9,5 cm ✕ 1 cm
Entraînement direct
Puissance nominale :30 W
Impédance :4 Ω
Caisson de grave :cône de 9,0 cm
Puissance nominale :30 W
Impédance :4 Ω
Niveau de pression sonore :77 dB/W·m
Fréquence de recouvrement :210 Hz
Gamme de fréquence :52 Hz
Dimensions :140 mm ✕ 301,5 mm ✕ 185 mm (L/H/P)
Poids :Environ 2,3 kg chacun
20 000 Hz
Accessoires
Fil d’antenne FM (1)
Antenne cadre AM (1)
Télécommande (1)
Piles (2)
Cordons électriques du haut-parleur (4)
Le modèle et les caractéristiques peuvent être sujets à modifications sans avis préalable.
VICTOR COMPANY OF JAPAN, LIMITED
EN, FR
0403MNMCREJEM
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
|