COLOR VIDEO CAMERA
INSTRUCTIONS
TK-WD310
(A)
VICTOR COMPANY OF JAPAN, LIMITED
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
information for future reference.
is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD.
is a registered trademark in Japan, the U.S.A., the U.K. and other countries.
Model No.TK-WD310
Printed in Thailand
Serial No.
© 2004 VICTOR COMPANY OF JAPAN, LIMITED
LWT0181-001A-H
LWT0181-001A-H
These are general IMPORTANT SAFEGUARDS and certain items
may not apply to all appliances.
IMPORTANT SAFEGUARDS
1. Read all of these instructions.
8. Slots and openings in the cabinet and the back or bottom are pro-
vided for ventilation, and to insure reliable operation of the appli-
ance and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by plac-
ing the appliance on a bed, sofa, rug, or other similar surface.
This appliance should never be placed near or over a radiator or
heat register. This appliance should not be placed in a built-in in-
stallation such as a bookcase unless proper ventilation is provided.
9. This appliance should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of
power supplied to your home, consult your dealer or local power
company. For appliance designed to operate from battery power,
refer to the operating instructions.
2. Save these instructions for later use.
3. All warnings on the product and in the operating instructions should
be adhered to.
4. Unplug this appliance system from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
5. Do not use attachments not recommended by the appliance manu-
facturer as they may cause hazards.
6. Do not use this appliance near water - for example, near a bathtub,
washbowl, kitchen sink, or laundry tub, in a wet basement, or near
a swimming pool, etc.
7. Do not place this appliance on an unstable cart, stand, or table. The
appliance may fall, causing serious injury to a child or adult, and
serious damage to the appliance.
10. This appliance system is equipped with a 3-wire grounding type
plug (a plug having a third (grounding) pin). This plug will only fit
into a grounding-type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet, contact your electrician
to replace your obsolete outlet. Do not defeat the safety purpose of
the grounding plug.
Use only with a cart or stand recommended by the
PORTABLE CART WARNING
(symbol provided by RETAC)
manufacturer, or sold with the appliance. Wall or
shelf mounting should follow the manufacturer’s in-
structions, and should use a mounting kit approved
by the manufacturer. An appliance and cart combi-
nation should be moved with care.
11. For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time, un-
plug it form the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning
and power-line surges.
S3125A
Quick stops, excessive force, and uneven surfaces
may cause the appliance and cart combination to
overturn.
12. Do not allow anything to rest on the power cord. Do not locate this
appliance where the cord will be abused by persons walking on it.
I
II
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for purchasing this product.
(These instrustions are for TK-WD310U and TK-WD310E.)
Before beginning to operate this unit, please read the instruction
manual carefully in order to make sure that the best possible per-
formance is obtained.
EASY INSTALLATION
The factory default settings are intended to give easy installation.
Please attach a lens, a power supply, a video cable and mount the
camera securely.You should now have good images.
Features
The additional information contained in this handbook is intended to
give additional flexibility to more demanding installations.
Ⅵ Backlight compensation over a wide area is realized by the 14-bit
Wide Dynamic Range feature.
The Wide Dynamic Range feature controls the exposure time using
a maximum of 5 sampling timing for the image within a single screen.
Even when shooting in areas with large difference in lightning, sub-
jects with difference in brightness can be viewed in a clear and natu-
ral state.
Ⅵ 1/3-inch high-resolution DPS device adopted as shooting element
to realize high picture quality with no smearing or blooming in areas
with high luminance. In addition, 1.9lx (during F1.2, 50%, AGC HIGH
setting) is realized for minimum subject brightness.
Ⅵ Horizontal resolution of 480 lines (typ.) and vertical resolution of over
400 lines allow display of finely detailed video.
Ⅲ Before starting an important recording, be sure to perform a test
recording in order to confirm that a normal recording is possible.
Ⅲ We do not accept liability for the loss of a recording in the case of
it becoming impossible to record due to a problem in the video
camera, VCR or video tape.
Ⅲ We do not accept liability for any damage to the camera in cases
when it is dropped because of incomplete installation due to not
observing the installation instructions correctly. Please be careful
when installing the camera.
Ⅵ New device adopted for use even under strong electric field condi-
tions.
Characters and symbols used in this instruction manual.
Ⅵ Compatible with CS mount and VIDEO auto iris/DC auto iris.
* When using the C mount lens, C mount adapter is required.
Ⅵ Various settings in each menu screen are possible.
Menu settings can be performed easily using single button opera-
tions.
CAUTION : Cautionary notes concerning operation of the unit.
MEMO
: Reference such as restrictions of features, etc.
: Reference page or item.
੬
Ⅵ 3 white balance modes of ATW, AWB and MANUAL are available.
ATW mode that adjusts the white balance automatically according
to the changes in lighting conditions (color temperature) or AWB/
MANUAL mode that automatically or manually adjusts and locks the
white balance of specific lighting conditions can be selected.
Ⅵ Camera title setting and display can be made.
Ⅵ Compact design allows installation in narrow spaces.
2
3
INTRODUCTION
Contents
Operating Precautions
●
●
●
To save energy, when it is not being used turn the system’s power
off.
This camera has been designed for indoor use.
When you use it outdoors, be sure to use an appropriate housing.
Do not install or use the camera in the following places.
• In a place exposed to rain or moisture.
INTRODUCTION
Features ............................................................................................. 2
Contents ............................................................................................. 4
Operating Precautions ....................................................................... 5
Names and Operations of Parts......................................................... 8
• In a place with vapor or oil soot, for example in a kitchen.
• When the ambient temperature rises above or falls below the ac-
ceptable range (from –10°C to 50°C).
CONNECTION/INSTALLATION
Basic System ................................................................................... 13
Mounting the lens............................................................................. 14
Connections on the back ................................................................. 16
Mounting the camera ....................................................................... 18
Auto iris lens adjustment .................................................................. 20
Back focus adjustment ..................................................................... 22
• Near a source of radiation, X-rays, strong radio waves or magne-
tism.
• In a place where corrosive gasses are generated.
• In a place subject to vibration.
• In a place with excessive dirt.
●
If this camera and the cables connected to this camera are used
where there are strong electromagnetic waves or where there is
magnetism present, for example near a radio or TV transmitter, power
transformer or an electric motor, the picture may produce noise and
the colours may be affected.
This camera incorporates an AGC circuit. As a result, when it is
used under low light conditions, the camera sensitivity is automati-
cally boosted and the picture may look uneven. However, this is not
a malfunction.
When this camera is used in the ATW mode, the recorded colours
may be slightly different from the actual colours due to the opera-
tional principles of the auto-tracking white balance circuit. However,
this is not a malfunction.
MENU SETTING
Menu settings................................................................................... 24
Menu tree ......................................................................................... 26
About menus .................................................................................... 27
FOCUS ADJUST screen .................................................................. 27
VIDEO ADJUST screen ................................................................... 28
WDR CUSTOM SETTINGS screen .............................................. 29
MANUAL WHITE BALANCE screen ............................................. 34
CAMERA SETTINGS screen ........................................................... 35
LENS ADJUST screen .................................................................. 35
CAMERA TITLE EDIT screen ....................................................... 37
FACTORY SETTINGS screen ......................................................... 39
●
●
●
●
Hunting may occur depending on the used lens. However, this is not
a malfunction of the unit.
The screen surroundings may appear dark depending on the used
lens.
OTHERS
Troubleshooting ............................................................................... 40
Specifications ................................................................................... 41
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Operating Precautions (continued)
●
The white balance (ATW) of this device is optimally set for sunlight.
Proper white balance may not be achieved for artificial lighting such
as fluorescent lighting, etc.
●
●
Blemishes: Small spots are normal, the camera contains compen-
sation functions for blemishes above 120 mV (p-p) in value. Please
contact your JVC authorised dealer for further information.
●
If you use this camera in locations where the camera is exposed to
fluorescent light, a slow color change may occur.
(White balance normal = 5,400 K, range is 2,500 K to 10,000 K.)
AGC HIGH(×2) and up: in this mode, ATW white balance may be
inaccurate.
For temperatures higher than the recommended temperature, the
slow shutter may not work correctly.
●
●
●
White balance performance decreases under poor lighting condi-
tions.
Observe the following when carrying out camera maintenance.
• Turn the power OFF before proceeding to carry out maintenance.
If it is contaminated seriously, clean the contaminated part with a
cloth (or a tissue) which has been soaked in a solution of water and
a neutral detergent.
●
●
The unit is to be powered by a DC 12 V or an AC 24 V power supply.
The AC 24 V power supply should conform to the following:
U type : Class 2 only
E type : Isolated power supply only
The beat may sometimes appear on the screen if gain is raised
when the line lock is in use, but the phenomenon takes place due to
the fluctuation of power frequency and is not a malfunction.
At Low light levels, video iris lens may “Hunt”. Please adjust iris
level on lens to minimise hunting.
●
●
Recommended range of operating temperature is 0°C to 35°C de-
grees. The camera will function outside these parameters to –10°C
to 50°C degrees. But processing errors may be apparent.
Line-Lock is set for 50 Hz 0.02 Hz. If line frequency is outside this
tolerance, picture may jitter and some interference may be visible in
high contrast scenes.
●
●
At low light level, when the slow shutter functions the screen may be
tinted.
6
7
INTRODUCTION
Names and Operations of Parts
[Front and Bottom]
3 [BF LOCK] Back focus locking screw (× 2: 2 mm)
This serves to fix the back focus-adjusting ring.
2
1
4 Camera-mounting bracket
The bracket has been attached on the bottom of the camera before
shipment. It can also be attached on the top according to the cir-
cumstance.
To re-attach the bracket use the threaded holes at the top, with the
camera mounting bracket locking screws 7.
4
5
5 Camera-mounting screw hole (1/4 inch)
Use this hole when mounting the camera
onto a fixer, pan/tilt unit, and the like.
(Use a screw shorter than 7 mm.)
3
MAX.
7mm
(੬ Page 18)
7
6 Rotation prevention hole
6
Make use of this rotation-preventive hole to prevent any fall when
mounting the camera. Make sure that the camera is securely
mounted.
1 Lens mount
For use with CS mount lens.
(C-mount lenses require a conversion ring.)
7 Camera mounting bracket fixing screws (× 2: M2.6 × 6 mm)
Be sure to use a 6 mm long screw.
2 Backfocus adjustment ring
Adjusting the back focus during lens installation.
Please refer to “Back focus adjustment” on ੬ Page 22 for instruc-
tions on how to adjust the back focus.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Names and Operations of Parts
[Rear Panel]
A [SET] button
During normal screen display, pressing and holding this button for
more than 2 seconds will display the MENU screen.
(੬ Page 24)
During MENU screen display, this button is pressed to display or
enable the selected menu item. The input digit will change when
entering the camera title.
DC12V
SEE INST-
AC24V
1
2
RUCTION
MANUAL
8
CLASS
2
ONLY (U TYPE)
ISOLATED POWER ONLY
(E TYPE)
When selecting EXIT in the TOP MENU screen, pressing this button
will return to the normal screen.
9
0
A
B
SET
SELECTOR
B [SELECTOR] button
Used when performing menu settings.
POWER
LL
VIDEO OUT
INT
C
This button is a multidirectional switch.
Ⅵ Pressing in a vertical direction (6 or 7) will select the menu item.
Ⅵ Pressing in a horizontal direction (8 or t) will change the set
value of the item. When entering the camera title, the input char-
acter will change.
8 [DC 12V, AC 24V] Power input terminals
To input DC 12V or AC 24V power.
C [INT/ LL] Selector Switch for Synchronizing System
This switch can set a synchronizing system of the camera.
INT:
9 [VIDEO OUT] Video signal output connector
This is set for internal synchronization (INT) .
LL (Line Lock): U type: 60Hz power region only
E type: 50Hz power region only
The camera’s vertical synchronization is locked to theAC 24V power
line frequency.
This BNC connector outputs a composite video signal. Connect this
to the video input connector of a video monitor, switcher, etc.
0 [POWER] Power indicator lamp
This lamp lights when power is supplied to the camera.
When switching between multiple cameras using a switcher, select-
ing this mode and adjusting the vertical phase can reduce the moni-
tor sync disturbances occurring when the camera image is switched.
(INT: At time of factory shipment)
10
11
INTRODUCTION
CONNECTION/INSTALLATION
Names and Operations of Parts
Basic System
[Side Panel]
Ⅵ System with up to 8 cameras
Power
cable
Camera 1
AC24V or
DC12V
COLOR VIDEO CAMERA
Video signal cable
Camera 2
AC24V or
DC12V
COLOR VIDEO CAMERA
IRIS
COLOR VIDEO CAMERA
VIDEO DC
Camera 8
AC24V or
DC12V
COLOR VIDEO CAMERA
E
D
•
•
•
•
•
•
Monitor
Monitor
D [VIDEO/DC] Iris Selector Switch
This should be set according to the type of lens if an automatic iris
control lens is used.
VIDEO : In case of lens with EE amp built-in.
(੬ Page 20)
DVR, etc.
REC
SR-L910
OPERATE
R
E
C
S
T
O
P
/
E
J
E
C
T
CHECK
VIDEO CASSETTE ECORDER
PAUSE/
REVERSE STILL
O
P
E
.
L
O
C
K
PLAY
COUNT/
CLOCK
SHIFT/TRACKING
RESET
/CANCEL
MENU
REW
FF
TIME
MODE
TIMER
REC
SET/V.LOCK
AL/PL
RESET
DC
: In case of lens without EE amp built-in.
(੬ Page 14)
Switcher
(DC : At time of factory shipment)
E [IRIS] Iris Terminal
This is connected to an automatic iris control lens.
(੬ Page 15)
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION/INSTALLATION
Mounting the lens
Mount the lens according to the procedures described below.
1. Before mounting a lens, check whether it is CS-mount lens.
Dimension (b) of the lens shown in the illustration must be as shown
in the table below. If (b) exceeds the value in the table, it may dam-
age the inside of the camera or correct mounting may be impos-
sible; never use such lenses. The F mark indicates a focal point.
Lens mount
Lens
Flange back (c)
12.5mm
Dimension (b)
5.5mm or less
CS mount lens
* When using the C-mount lens, use the conversion ring (CM46633-
001, MOUNT ADAPTOR).
1.
(b)
F
2. Attach the included ferrite core to the lens cable. Please attach it
as close to the camera as possible.
3. Mount the lens on the camera by turning the lens clockwise. Adjust
its position.
(c)
4. When using an auto-iris lens with an EE amplifier, turn the switch to
the “VIDEO” side. When no EE amplifier is equipped, turn the switch
to the “DC” side.
5. If the lens has an auto-iris mechanism, connect the lens cable after
checking the pin arrangement.
3.
4.
COLOR VIDEO CAMERA
IRIS
IRIS
If the lens cable has a different type of plug, use the 4-pin plug.
[4-pin plug part no: SCV2859-001]
VIDEO DC
VIDEO
DC
Contact your dealer of purchase concerning the 4-pin plug.
1
2
3
4
Lens DC IRIS
VIDEO IRIS
2.
Pin No.
(does not contain EE amplifier) (contain EE amplifier)
–
+
1
2
3
4
Brake
Brake
Drive
Drive
9V [max 50mA]
NC
5.
+
VIDEO
GND
3
–
1
Ferrite core
4
2
14
15
CONNECTION/INSTALLATION
Connections on the back
●
Turn off the power supply to all components before making con-
nections.
Ⅵ Power supply (DC 12 V or AC 24 V)
Connect the DC 12 V or the AC 24 V power supply to the DC 12V/
AC 24V terminals. To prevent connection errors or a cable discon-
nection, we recommend the use of lug plates for the connections.
The following table shows the connection distances and connection
cables provided that 2-conductor VVF cables (vinyl-insulated vinyl
sheath cables) are used.
Power supply (DC 12 V or AC 24 V)
DC12V
Maximum extension
(reference)
SEE INST-
AC24V
1
2
RUCTION
MANUAL
100 m
260 m
410 m
500 m
CLASS
2
ONLY (U TYPE)
ISOLATED POWER ONLY
(E TYPE)
1.0qmm 1.6qmm 2.0qmm 2.6qmm
and more and more and more and more
Conductor diameter
Memo
SET
SELECTOR
POWER VIDEO OUT
● If thin cables are used (i.e. with a high resistance), a significant
voltage drop will occur when the unit is at its maximum power
consumption. Either use a thick cable to restrict the voltage drop
at the camera side to below 10%, or place the power supply
near to the camera. If voltage drop occurs during operation, the
performance will be unstable.
LL
INT
Monitor
Ⅵ Video signal cable (BNC)
● Attach the cable conductors so that they do not come into con-
tact with the drop prevention wires.
● Do not allow input from both a DC 12 V and AC 24 V power
supply at the same time.
Connect the coaxial cables (BNC) to the VIDEO OUT connector
(BNC).
● When using a DC 12 V power supply, ensure that the polarities
of the cable are correct.
● The AC 24 V power supply should conform to the following:
U type: Class 2 only
E type: Isolated power supply only
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION/INSTALLATION
Mounting the camera
Camera mounting
screw hole
Camera mounting
bracket
DC12V
AC24V
SEE INST-
RUCTION
MANUAL
1
2
CLASS
2
ONLY (U TYPE)
6mm
2mm
ISOLATED POWER ONLY
(E TYPE)
SET
SELECTOR
POWER VIDEO OUT
LL
INT
M3 × 6
Rotation prevention hole
Fall Prevention
When mounting the camera on a fixer, pan/tilt, etc., use the camera
mounting screw hole located on the camera-mounting bracket.
•
Exercise maximum caution when installing the unit to the wall or
ceiling. You should not engage in the installation work yourself. Ask
a professional to do the job, since the fall of the unit can result in
injuries and accidents.
CAUTION:
Use the screw with a length shorter than
7mm from a camera-mounting face.
•
•
When installing the unit on a fixer, Pan/Tilt unit, etc., make sure to
install it firmly using a rotation-preventing hole provided to prevent
fall.
To prevent fall, connect the unit to a section with sufficient strength
(ceiling slab or channel) using a fall prevention wire such as a wire
chain and the like. Use the black screw on the back of the unit for
installation.
MAX.
7mm
For the used safety cable, pay particular caution to the length,
strength, pull, material (insulation), etc.
Specified screw (M3 × 6 mm)
Never use any screw longer than the specified length as the inside
can be damaged.
Furthermore, make use of the rotation prevention hole to prevent the
camera from falling and securely mount the camera.
Special precautions must be taken for mounting the camera on a wall
or a ceiling. We are not liable for any damage caused by improper
installation.
•
18
19
CONNECTION/INSTALLATION
Auto iris lens adjustment
Connect the camera according to the connection method, turn it on,
display an image on the monitor, and check the image. The white bal-
ance adjustment mode is selected. ੬ Page 33 “WHITE BALANCE”
The camera has been factory-adjusted to the best position, but it may
need to be adjusted according to the object conditions or combination
of lenses. If the image is unnatural, adjust it as follows: (Also read the
instruction manual of the lens.)
• LEVEL adjustment
Monitor screen
Too bright
LEVEL turning direction
Counterclockwise (Toward L)
Clockwise (Toward H)
Too dark
Memo
● If the sensitivity adjustment LEVEL is turned excessively to L,
the sensitivity increases because of the AGC function of the
camera, and the image looks grainy.
Ⅵ For video auto iris lens (auto iris lens with built-in EE
amp)
Set the VIDEO/DC switch on the side of the unit to “VIDEO” and
adjust the LEVEL volume on the lens.
● At Low light levels, video iris lens may “Hunt”. Please adjust iris
level on lens to minimise hunting.
Level adjustment
Ⅵ For DC auto iris lens (auto iris lens without built-in EE
amp)
Set the VIDEO/DC switch on the side of the unit to “DC” and adjust
the LEVEL in the LENS ADJUST screen. (੬ Page 35)
COLOR VIDEO CAMERA
ALC adjustment
(Does not operate)
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION/INSTALLATION
Back focus adjustment
Be sure to make back-focus adjustments when changing the lens mount-
ing method or using a different lens.
• With a fixed-focus lens
If the focus can not be adjusted correctly by rotating the lens focus ring,
adjust the back focus as follows.
●
●
To make accurate back focus adjustments, carry out adjustments in
a state where the lens iris is released.
To open the lens iris, set MODE in the FOCUSADJUST menu screen
to ON. (੬ Page 27)
1. Loosen the back focus locking screws by turning it counterclock-
wise (
) with a Phillips screwdriver. (2 locations)
2. Shoot a pattern closely.
3. Turn the lens focus ring to ∞.
The auto iris lens may operate under extremely bright conditions
(7000lx or higher). In this case, use an ND filter to adjust the amount
of light.
4. Turn the back focus adjustment ring to focus at the best point.
(The ND fiter acts to reduce the amount of incident light entering the
lens evenly over the entire wavelength band.)
5. Tighten the back focus locking screws by turning it clockwise (
).
(2 locations)
Lens focus ring
Back focus adjust ring
• With a zoom lens
If the image is out of focus when zooming (telephoto wide-angle), ad-
just the camera as follows:
1. Loosen the back focus locking screws by turning it counterclock-
wise (
) with a Phillips screwdriver. (2 locations)
2. Shoot a comparatively dark scene with thin lines.
3. Set the lens to the maximum telephoto position, and adjust the lens
focus.
Phillips screwdriver
4. Set the lens to the maximum wide-angle position, and turn the back
focus ring to adjust the focus.
Back focus locking screws
(Repeat steps 3. and 4. two or three times.)
Memo
If the iris cable length of the lens is insufficient when turning the
5. Tighten the back focus locking screws by turning it clockwise (
).
(2 locations)
back focus adjustment rings, lock the back focus locking screws,
turn the lens and loosen the back focus locking screws again for
achieving back focus.
22
23
MENU SETTING
Menu settings
4. Press the SELECTOR button in the
vertical direction (6 or 7) and
move the cursor (>) to the desired
item.
DC12V
AC24V
— — —
V
I
D E O A D J UST — — —
SEE INST-
RUCTION
MANUAL
1
2
WDR
AGC
M
D E
MODE 2
L OW
MODE
WH I T E B A L ANC E
COL OR L E VE L
A TW
CLASS
2
ONLY (U TYPE)
NORMAL
NORMAL
ISOLATED POWER ONLY
(E TYPE)
E N HA NCE L E VE L
E X
I
T
5. Press the SELECTOR button in the
horizontal directional (8 or t) and
change the set value.
Ⅵ To change the set value of multiple
items, repeat steps 4. and 5. above.
SET
SELECTOR
POWER
LL
VIDEO OUT
INT
— — —
— — —
V
I
D E O A D J UST
D E
MODE
SELECTOR
button
WDR
AGC
M
MODE 2
H
I
GH
WH I T E B A L ANC E
COL OR L E VE L
A TW
NORMAL
NORMAL
E N HA NCE L E VE L
6. Exit the menu screen.
Move the cursor (>) to EXIT of the
menu screen and press the SET
button.
E X
I
T
SET button
7. Return to the normal screen.
Move the cursor (>) to EXIT of the
MENU screen and press the SET
button.
— — —
— — —
V
I
D E O A D J UST
D E
MODE
Cursor
Operation
WDR
AGC
M
MODE 2
H
I
GH
WH I T E B A L ANC E
COL OR L E VE L
A TW
NORMAL
NORMAL
— — —
— — —
MENU
1. Press and hold the SET button for
more than 2 seconds.
● The MENU screen appears.
E N HA NCE L E VE L
E X
I
T
F OCUS A D J US T..
D EO A D J US T..
CAMERA S ET T I NGS ..
F AC T OR Y S ET T I NGS ..
T
V
I
● The screen returns to the normal
screen (screen with no menu dis-
play).
EX
I
2. Press the SELECTOR button in
the vertical direction (6 or 7) and
move the cursor (>) to the desired
submenu.
— — —
F OCU S A D J US T..
— — —
MENU
V
I
DEO A D J US T..
CAME RA S ET T I NGS ..
F AC T OR Y S ET T I NGS ..
Submenu (“..” displayed
at the end.)
E X
I
T
3. Press the SET button
● The selected submenu screen
appears.
— — —
V
I
D E O A D J UST — — —
WDR
AGC
M
D E
MODE 2
L OW
MODE
WH I T E B A L ANC E
COL OR L E VE L
A TW
NORMAL
NORMAL
E N HA NCE L E VE L
E X
I
T
Memo
When returning to the normal screen from the TOP MENU screen
by selecting EXIT, the menu settings will be stored in the unit
memory.
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU SETTING
Menu tree
About menus
The menu screens are structured as shown below.
FOCUS ADJUST............ Used during focus adjustment of the auto iris
lens.
੬
Page 27
(੬ Page 27)
VIDEO ADJUST ............. Sets the wide dynamic range, gain, color tem-
—
—
—
—
—
—
F O C U S A D J UST
MOD E
E X
OFF
I
T
perature, white balance, etc.
(੬ Page 28)
CAMERA SETTINGS ..... Sets the DC iris, camera title and vertical
phase.
(੬ Page 35)
੬
Page 28
੬
Page 29
—
—
—
—
—
—
—
—
—
—
—
—
—
—
WDR CUSTOM SETTINGS
—
—
MENU
V
I
D E
O
A D J UST
FO CUS A D J US T..
WD R
WD R
EXP.
B
I
I
I
AS
WD R MOD E
AGC MOD E
WH
COL OR
E N HA NCE
E X
MOD E2
L OW
–
36
0
–
3
3
1
6
V
I
DEO A D J US T..
8
FACTORY SETTINGS ... Restores the menu settings to the factory set-
tings.
(੬ Page 39)
CAMERA
S
E T
T
I
T
NGS..
NGS ..
A TW
I
T
E
B A L ANC E
L
M
I
T
F ACT OR Y
S
ET
I
NORMAL
NORMAL
L
E
VE
E
L
2 5
6
EX
I
T
L
V E
L
I
T
B
AS
–18
–4
8
0
WD R BR
EX
I
G HT
10 0
1 0 4
15
I
T
੬
Page 35
੬ Page 34
—
—
—
—
—
0
—
CA MERA SE T
T
I
N G S
—
—
MANUAL WHITE BALANCE
—
—
FOCUS ADJUST screen
L ENS A DJ U S T ..
CAME RA
CAME RA
R – B
T
T
I
I
T
T
L E
L E E D
O F F
T
B L UE
R ED
I
E
X
I
T
V
PHASE
MODE
Default setting: OFF
0
8
4
1
4
Normal screen
EX
I
T
Used during focus adjustment of the auto iris lens.
When set to ON, the focus adjustment accuracy is increased by forcing
the iris open and with a shallower focal point.
੬
Page 35
—
—
—
—
—
2
—
L
E NS A DJ US
T
0
੬
Page 39
DC G A
I
N
0
0
6
5
5
5
—
—
—
—
—
—
F ACT OR Y S ET T N GS
I
Memo
DC O F F S E T
CA NC E L
CL EAR
1
0
1
2
0
1
0
E X
I
T
When exiting the FOCUS ADJUST screen, MODE will automati-
cally be set to OFF.
Memo
● When selecting an item with “..” at the end, the submenu screen
will appear.
● When selecting EXIT in each screen, the screen will return to
the previous screen.
When selecting EXIT in the MENU screen, the screen will return
to the normal screen.
26
27
MENU SETTING
VIDEO ADJUST screen
WDR MODE
WDR CUSTOM SETTINGS screen
The Wide Dynamic Range (WDR) is adjusted manually.
Operation
Default setting: MODE2
Setting of the wide dynamic range (WDR) is performed.
CUSTOM : Manually adjusts the wide dynamic range.
Pressing the SET button will display the WDR CUSTOM
SETTINGS screen. (੬ Page 30)
1. Display the VIDEO ADJUST
screen. (੬ Page 24)
— — — V I D E O A D J UST — — —
WDR MOD E
CUS TOM ..
L OW
MODE1 : When shooting in a bright area outdoors
MODE2 : Standard video
MODE3 : To brighten the video taken indoors
MODE4 : To brighten areas with little luminance in video with large
difference in brightness
AGC MOD E
2. Select WDR MODE and press the
SELECTOR button in the horizon-
tal direction (8 or t) to change
the setting to CUSTOM.
A TW
WH I T E B A L ANC E
COL OR L E VE L
E N HA NCE L E V E L
NORMAL
NORMAL
E X
I
T
3. Press the SET button.
(When moving from dark indoors to outdoors during shoot-
ing)
● The WDR CUSTOM SET-
TINGS screen will appear.
FLUOR : For video taken under lighting (fluorescent lighting, etc.)
that synchronizes with commercial electrical power supply
frequency resulting in periodical change in colors
(When in a 60Hz area, set to LL (Line Lock).)
(੬ Pages 11, 36)
—
—
WDR CUSTOM SETTINGS
—
—
4. Press the SELECTOR button in
the vertical direction (6 or 7) and
move the cursor (>) to the item to
set.
5. Press the SELECTOR button in
the horizontal direction (8 or t)
to change the set value.
WD R B I AS
– 36
– 8
2 5
3 6
3 6
1 8
WD R
L
I
M
I T
0
EXP. B I AS
–18
–4
WD R BR I G HT
10 0
Memo
1 0 4
15 0
EX I T
● The Wide Dynamic Range feature controls the exposure time
using up to 5 sampling timing within a single screen according
to the brightness of the subject. With the Wide Dynamic Range
feature, the subject with a large difference in brightness with the
remainder of the screen can be viewed in a clear, natural state
even when shooting in areas with large difference in lighting
(such as indoors easily influenced by backlight, afternoon sun,
etc., entrances and near windows).
6. To exit setting, select EXIT and
press the SET button.
Cursor
Set value
● The screen returns to the
VIDEO ADJUST screen.
Memo
● Set the mode by first checking under the usage environment.
● WDR custom mode allows manual adjustment. (These are over-
written if other modes are selected.)
● When exiting the WDR CUSTOM SETTINGS screen without
changing settings, MODE1 will be automatically selected for
WDR MODE.
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU SETTING
VIDEO ADJUST screen (continued)
Item
WDR BIAS
Content
AGC MODE
Default setting: LOW
Sets the low/mid luminance level of the Wide
Dynamic Range
● To brighten video with low/mid luminance:
Increase the value
Sets the maximum gain of AGC (Auto Gain Control).
You can set this device to maximum gain by the use of the slow shutter.
Refer to the chart below and set according to the subject.
● To darken video with low/mid luminance:
Decrease the value
[Setting range: -36 ~ -8 ~ 36]
Setting : Gain
Gain
0dB 10dB
22dB
28dB
34dB
40dB
46dB
Setting
OFF
WDR LIMIT
EXP. BIAS
Sets the maximum value of the Wide Dynamic
Range
● To shoot a subject with large difference in
brightness:
Increase the value
: Slow-speed shutter
LOW
21dB
MID
HIGH
28dB + [×2 (6dB)]
22dB + [×4 (12dB)]
×2
HIGH (×2)
HIGH (×4)
SUPER (×2)
SUPER (×4)
SUPER (×8)
ULTRA (×16)
[Setting range: 0 ~ 25 ~ 36]
×
2
×
4
2
Adjusts the output properties for the luminance
level of the subject
● To further sharpen a dark subject:
Increase the value
● To further sharpen a bright subject:
Decrease the value
[Setting range: -18 ~ -4 ~ 18]
34dB + [×2 (6dB)]
28dB + [×4 (12dB)]
×
×2
2
×4
×4
×8
22dB ×8 (18dB)]
×
+ [
×16
22dB + [×16 (24dB)]
E.g. When set to HIGH (×4)
As the subject darkens, the 22dB to ×2 slow-speed shutters operate to brighten the screen. If
the subject continues to darken, the 28dB to ×4 slow-speed shutters then take over and
continue to brighten up the screen.
WDR BRIGHT Adjusts the brightness of the entire video.
● To further brighten the entire video:
Increase the value
* Sensitivity is increased when the slow-speed shutter is operating, but movement on the
screen may appear a little stilted.
[Setting range: 100 ~ 104 ~ 150]
30
31
MENU SETTING
VIDEO ADJUST screen (continued)
Memo
● When raising the gain, noise will appear in the screen for dark
areas.
WHITE BALANCE
Default setting: ATW
The white balance adjustment mode is selected. White balance can be
adjusted for lighting with color temperature in the range between 2,500K
and 10,000K.
● When in a dark area and setting AGC MODE to HIGH (×2) and
up:
• Video may temporarily lock or noise may be noticeable.
• The entire screen may temporarily change from a dark to a
bright state.
ATW
: The unit will be in theAuto Tracking White Balance mode.
The white balance will be adjusted automatically accord-
ing to the color temperature of the lighting.
AWB (SET) : When pressing the SET button (under 1 second), the white
balance will be adjusted automatically for the current light-
ing (color temperature).
• When especially dark, depending on light intensity, the Wide
Dynamic Range (WDR) feature will not function.
(The WDR feature will function in normal light intensities.)
• The right edge of the screen may temporarily jiggle.
The result of the white balance automatically adjusted
will be stored in the unit memory.
• For temperatures higher than the recommended temperature,
the slow shutter may not work correctly.
Use this setting when using the white balance that has
been adjusted automatically.
MANUAL.. : Use this setting when manually adjusting the white bal-
ance for the current lighting (color temperature).
When pressing the SET button, the screen for manually
adjusting the white balance appears. (
੬
Page 34)
The result of the white balance manually adjusted will be
stored in the unit memory.
Use this setting when using the white balance that has
been adjusted manually.
Memo
● When adjusting the white balance for AWB (SET) or MANUAL,
fill the entire screen with a white subject (such as paper, cloth,
etc.).
● If proper colors cannot be achieved in the ATW mode, use the
AWB (SET) or MANUAL mode.
● In some cases, proper white balance may not be achieved even
in the MANUAL mode for artificial lightning such as fluorescent
lighting, etc.
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU SETTING
VIDEO ADJUST screen (continued)
COLOR LEVEL
Default setting: NORMAL
MANUAL WHITE BALANCE screen
The color level of video signals is adjusted.
If the entire screen appears to be reddish or bluish in color as the result
of automatic white balance adjustment, manually adjust the white bal-
ance.
●
●
To lighten colors: decrease the value.
To darken colors: increase the value.
[Setting range: -5 ~ NORMAL ~ 5]
Preparation
— — — V I D E O A D J UST — — —
ENHANCE LEVEL
The aperture control/contour level of the video signals is adjusted.
Soften video: decrease the value.
Sharpen video: increase the value.
[Setting range: -5 ~ NORMAL ~ 5]
Default setting: NORMAL
WDR MOD E
AGC MOD E
MODE 2
L OW
Fill the entire screen with a white sub-
ject (such as paper, cloth, etc.).
MAN U AL..
NORMAL
NORMAL
WH I T E B A L ANC E
COL OR L E VE L
E N HA NCE L E VE L
●
●
E X
I
T
Operation
1. Display the VIDEO ADJUST
screen. (
੬
Page 24)
CAMERA SETTINGS screen
LENS ADJUST screen
2. Set WHITE BALANCE to
MANUAL and press the SET but-
ton.
—
—
MANUAL WHITE BALANCE
—
—
This setting is performed when using the DC auto iris lens.
R – B
E X I
B L UE
R ED
● The MANUAL WHITE BAL-
ANCE screen will appear.
T
Operation
3. Press the SELECTOR button in
the vertical direction (6 or 7) and
move the cursor (>) to R-B.
4. Press the SELECTOR button in
the horizontal direction (8 or t).
● Pressing in the 8 direction will
increase bluish tint.
● Pressing in the t direction will
increase the reddish tint.
5. To end adjustment, press the SE-
LECTOR button in the vertical di-
rection (6 or 7) to select EXIT
and press the SET button.
1. Display the CAMERASETTINGS
screen. ( Page 24)
2. Select LENS ADJUST and press
the SET button.
● The LENS ADJUST screen ap-
pears.
— — — L E NS A DJ US T — — —
DC G A I N
੬
0
6 0
2 5 5
DC O F F S E T
1 0 0
1 2 0
1 5 0
Set value
E X
I
T
3. Press the SELECTOR button in
the vertical direction (6 or 7) and
move the cursor (>) to the item to
set.
4. Press the SELECTOR button in
the horizontal direction (8 or t)
to change the set value. Pressing
and holding the button will con-
tinuously change the value.
Memo
The result of the white bal-
ance adjusted manually will
be stored in the unit
memory.
Item
Set value
To use the manually ad-
justed white balance, set
WHITE BALANCE to
MANUAL.
34
35
MENU SETTING
CAMERA SETTINGS screen (continued)
5. When selecting EXIT and press-
ing the SET button, the screen will
return to the CAMERA SET-
TINGS screen.
CAMERA TITLE EDIT screen
Up to 24 characters can be entered for the camera title. The entered
camera title will appear on the bottom left of the screen when the CAM-
ERA TITLE menu item is set to ON.
Item
DC GAIN
Content
Adjusts operating speed of the DC auto iris lens.
Adjust according to the lens used.
Operation
Increasing the value: the speed will increase
[Setting range: 0 ~ 60 (default setting) ~ 255]
* Depending on the lens, hunching may occur
when setting this value too high. In this case,
lower the value.
1. Display the CAMERA SETTINGS
screen. (੬ Page 24)
2. Press the SELECTOR button in
the vertical direction (6 or 7)
and move the cursor (>) to se-
lect CAMERA TITLE EDIT.
3. Press the SET button.
● The 1st character will appear
in purple and input will be al-
lowed.
— — — CA MERA SE T T I N G S — — —
L ENS A DJ U S T ..
CAME RA
CAME RA
T
T
I T L E
O F F
I T L E E D I
T
V
PHASE
0
84
1 0 4
EX
I
T
DC OFFSET
Standard level (brightness) for controlling the DC
auto iris operation is set.
Increasing the value: the screen will become darker
[Setting range: 100 ~ 120 (default setting) ~ 150]
1st character
CAMERA TITLE
Default setting: OFF
4. Press the SELECTOR button in
the horizontal direction (8 or t)
and select the desired character.
5. Press the SET button to confirm
the 1st character. The 2nd char-
acter will then appear in purple.
6. Repeat steps 4. and 5. above to
enter up to 24 characters.
7. To end character entry, press the
SELECTOR button in the verti-
cal direction (6 or 7) and move
the cursor (>) to another item.
Whether to display the camera title is set.
OFF
ON
:
:
Camera title is not displayed.
Camera title is displayed.
V PHASE
To correct a character, press
the SET button to display the
character to correct in purple,
press the SELECTOR button in
the horizontal direction (8 or
t) to change the character.
Vertical phase during line lock is adjusted. The vertical phase can be
adjusted to other cameras. This setting is enabled when the LL/INT
switch on the back of the unit is set to LL.
●
Press the SELECTOR button in
the horizontal direction (8 or t)
to set. Pressing in the button to
the right (t) will advance the
phase and pressing to the left (8)
will delay the phase.
— — — CA MERA SE T T I N G S — — —
L ENS A DJ U S T ..
CAME RA
CAME RA
T
T
I T L E
O F F
I T L E E D I
T
V
PHASE
0
84
1 0 4
EX
I
T
Set value
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU SETTING
FACTORY SETTINGS screen
Returns set values to their factory settings.
Ⅵ Allowed characters
8 direction (SELECTOR button) t direction
Operation
1. Display the FACTORY SET-
TINGS screen. (੬ Page 24)
2. Press the SELECTOR button in
the vertical direction (6 or 7)
and move the cursor (>) to
CLEAR.
— — —
F OCUS A D J U S T ..
— — —
ME NU
Space
V
I D EO A D J US T ..
CAME RA S E T T
I
NGS..
NGS ..
F AC T OR Y S E T T
E X I T
I
3. Press the SET button.
● Settings including the camera
title will be restored to the fac-
tory settings and the screen
will return to the MENU screen.
* Select CANCEL and press the
SET button to return to the
MENU screen without chang-
ing settings.
Cursor
— — — F ACT OR Y S ET T I N GS — — —
CA NCE L
CL E AR
4. Exit the menu screen.
Select EXIT within the MENU
screen and press the SET but-
ton to return to the normal screen.
Pressing the SELECTOR button in the t direction will select the
character on the right and pressing in the 8 direction will select the
character on the left. Pressing and holding the button will continu-
ously change the character selected.
Memo
When CAMERA TITLE is set to ON, a background the width of 1
character is displayed, even when there is no camera title entered.
If a CAMERA TITLE of more than 1 character is entered, a back-
ground the width of 24 characters is displayed.
38
39
OTHERS
OTHERS
Troubleshooting
Specifications
Image pickup device
Number of effective pixeis : 380,000 pixels ((H) 720 × (V) 540)
: 1/3 type WDR digital image device
Symptom
Remedy
Drop in voltage of the power supply can
be considered. Check the length and
thickness of the power supply cable.
(੬ Page 17)
The operation becomes un-
stable
Synchronizaton method
Scanning frequency
: Internal,Line lock
:
U Type (H) 15.734 kHz, (V) 59.94 Hz
E type (H) 15.625 kHz, (V) 50.0 Hz
: 480 TV lines (H)
Resolution
VIDEO OUT
: Composite video signal
1 V(p-p), 75Ω (BNC)
: 50 dB (AGC OFF)
The auto iris will not operate Set the VIDEO/DC switch on the side
of unit according to the type of auto iris
lens used.
(੬ Pages 20, 21)
Video S/N ratio
Minimum required illumination : 1.9 lx (50%, F1.2, AGC HIGH)
0.5 lx (50%, F1.2, AGC ULTRA(×16))
0.95 lx (25%, F1.2, AGC HIGH)
0.25 lx (25%, F1.2, AGC ULTRA(×16))
: CS mount
: AC 24 V ` 50 Hz/60 Hz
DC 12 V
There is noise in the screen Lower the gain using the AGC MODE
or increase in residual im- menu item.
Lens mount
Power supply
ages
ULTRA SUPER HIGH MID LOW OFF
(MAX)
(MIN)
Gain
Power consumption
Ambient temperature
: U type Approx. 5.7 W
E type Approx. 400 mA
: –10°C to 50°C (operation)
0°C to 35°C (recommended)
: 330 g
(੬ Page 31)
When using in an environment where
there are changes in the light source,
set the WHITE BALANCE menu item
to ATW.
The colors of the screen are
not natural
Mass
Accessory
: Instructions
U type .............................. 1
E type .............................. 2
Ferrite core ....................... 1
(੬ Page 33)
White balance adjusted
automatically/manually
cannot be used
Set the WHITE BALANCE menu item
to AWB or MANUAL.
(੬ Page 33)
Ⅵ External Dimensions (Unit: mm)
U1-32
107
95
50
The camera title will not ap- Set the CAMERA TITLE menu item to
pear
ON.
(੬ Page 36)
COLOR VIDEO CAMERA
When adjusting the vertical phase dur-
ing line lock, set the LL/INT switch on
the back of unit to LL.
The vertical phase cannot be
adjusted using the V PHASE
menu item
TRIPOD
BASE
1/4-20UNC
MOUNTING HOLE
33
(੬ Page 11)
Design and specifications are subject to change without notice.
40
41
Download from Www.Somanuals.com. All Manuals Search And Download.
|