JBL Speaker SAM3HA User Manual

®
SYNTHESIS THREE ARRAY  
SAM3HA,  
SAM3VA  
OWNER S AND  
INSTALLER S  
MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
®
Congratulations on purchasing this JBL Synthesis Three Array home theater speaker. This product represents the  
synthesis of everything that JBL has learned about the emotional power of audio and video in sixty years of preemi-  
nence in the field. It sets new benchmarks in the use of “high technology” and provides you with the experience of  
being in some of the world’s greatest movie houses and concert halls, right at home! JBL’s Synthesis Three Array  
speaker systems feature the following:  
®
THX ULTRA2 -LICENSED HOME AUDIO SYSTEM: When used with a THX controller and amplifiers, your  
speaker system will deliver a state-of-the-art THX home theater experience to your living room. You will hear in your  
home exactly what the director and sound engineer heard in the recording studio. The system will reproduce the  
audio flawlessly and without distortion.  
ULTRAHIGH-FREQUENCY COMPRESSION DRIVER: 1" (25mm) Pure-titanium compression driver with aluminum  
edge-wound voice coil and 2" (51mm) neodymium motor assembly, mounted in a constant-directivity horn for extended  
high-frequency response to exceed SACDand DVD-Audio specifications.  
High-Power Compression Horn: Horns are commonplace in movie theaters across the world, because of  
their high power handling and well-defined high-frequency output. The horns employed in SAM3 have very low dis-  
tortion, and a well-controlled directivity, to put the dialogue at the center of the screen and the effects all around you.  
ACCURATE MID-BASS DRIVERS AND SUBWOOFERS: The 6-1/2" (165mm) mid-bass drivers incorporate many  
of JBL’s patented technologies – such as Symmetrical Field Geometry(SFG), Symmetrical Inductance Modulation  
(SIM) and Vented Gap Cooling(VGC) – as well as unique cone and dome materials, to provide tight, smooth  
midrange sound without harshness, stridency or listener fatigue. From two to as many as four 12" or 15" (305mm or  
380mm) high-power subwoofers complete the experience with earth-shattering, deep bass.  
COMMON VOICING: Synthesis Three Array uses common voicing across the front three channels. Since identical  
drivers are used, each speaker has the same tonal qualities, thus as a sound is panned from one side to the other,  
there will be no change in timbre.  
MAGNETIC SHIELDING: All front speakers are magnetically shielded, allowing you to place them near video mon-  
itors without generating interference or distorting the picture.  
DUAL “INSIDE” NEODYMIUM, SHIELDED MOTOR STRUCTURE: The magnetic material is placed at the  
center of the motor structure, INSIDE the voice coil diameter. This inverted dual-magnet configuration improves  
magnetic shielding even further, reducing the extraneous magnetic field, and offers increased acoustic output.  
DEEP-ANODIZED CONE AND DOME MATERIAL: The special deep-anodized aluminum cone and dome material,  
together with the motor features, helps to reduce midband distortions to very low levels (approximately 50dB to 60dB  
below the fundamental signal driven at 100dB output).  
TWO-STAGE PHASE PLUG: The phase plug is a key element in this compression driver. The accuracy of the phase  
plug geometry is most important to achieve a wide and flat frequency response. The pressure distribution in the phase  
plug is manipulated by adjustments to the number and width of the slots and even the plug inside streamline is opti-  
mized to achieve a coherent pressure front across the operating range at the exit of the phase plug.  
SYMMETRICAL INDUCTANCE MODULATION (SIM): The flux-stabilizing ring and copper gap ring are also opti-  
mized for size and position, to help minimize or eliminate “asymmetrical inductance modulation.” Minimizing this  
asymmetrical inductance modulation leads to even further distortion reduction and improved vocal clarity.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPEAKER PLACEMENT  
Positioning your loudspeakers properly is critical in order to achieve the  
sonic performance of a home theater. Please read the following section  
for guidance in correct and optimal placement.  
L
C
R
LEFT AND RIGHT SPEAKERS: If you have purchased a Synthesis Three  
Array Digital Home Theater System, then the model SAM3VA will serve as  
your front left and right main speakers.  
VIEWING  
POSITION  
Since the left and right speakers have been designed for maximum localization  
of sound, they should be placed with the center of the speakers at about the  
same height on screen as the actors would be, to aid in the illusion that the  
actors’ voices are coming directly from their on-screen images. Ideally, the  
speakers will be placed about 45 degrees apart from each other, viewed  
from the listening position, so that the distance between the speakers is the  
same as each speaker’s distance from the listener (see Figure 1).  
FLOOR PLAN  
Figure 1. 5.1-Channel system  
CENTER CHANNEL SPEAKERS  
SAM3VA: If you have purchased the vertical channel speaker (model  
SAM3VA) for the center position, be sure to place it vertically during  
installation in order to take advantage of its sound-dispersion characteristics.  
If you mount it horizontally, it will not provide the correct dispersion pattern.  
If the speaker is being used with a perforated projection screen, it should be  
mounted behind the center of the screen (see Figure 2). If a nonperforated  
projection screen, plasma display or other fixed video device is being used  
in the installation, the preferred center speaker is the model SAM3HA (below).  
Figure 2.  
SAM3HA: If you have purchased the horizontal channel speaker (model SAM3HA) for the center position, be sure  
to position it horizontally during installation in order to take advantage of its  
sound-dispersion characteristics. If you mount it vertically, it will not provide  
the correct dispersion pattern. Although the preferred speaker model to be  
used with a perforated projection screen is the vertical model SAM3VA  
(above), the SAM3HA horizontal speaker may be used instead and should be  
mounted behind the center of the screen. If a nonperforated projection  
screen, plasma display or other fixed video device is being used in the  
installation, then the recommended location is directly below and as close  
as possible to the video display (see Figure 3), although the inverse of this  
Figure 3.  
method will work also.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPEAKER PLACEMENT  
NOTE: It is extremely important to place the tweeter/mid-bass arrays for each of the center, left and right speakers  
at the same height. The horn array containing the tweeter in the center channel speaker should be no more than two  
feet (0.6 meter) higher or lower than those in the left and right speakers. This preserves the “localization integrity” of  
“sound pans,”in which the sound appears to move from left to center to right. If the program material also appears to  
travel up and down, it can destroy the illusion of panning effects and so should be avoided.  
AMBIENT SURROUND SPEAKERS: Although it has been common for many years to use a number of surround  
speakers in commercial movie houses, until recently, the traditional home theater configuration called for 5.1  
channels, i.e., front left, center, front right, surround left and surround right, plus a low-frequency-effects channel.  
The newer surround formats that are appearing in consumer audio equipment are calling for more complicated 6.1-  
and 7.1-channel systems. The advantages of using additional speakers are many. Additional channels enable a more  
versatile use of directionality for a more accurate surround presentation. Also, a higher overall sound-pressure level  
can be achieved with less energy expenditure from any individual speaker. Placement of the surround speakers  
remains critical.  
5.1-CHANNEL SYSTEMS  
The ambient surround speakers work optimally if they are placed as far back  
from the screen as the viewing chairs are. If there are two rows of chairs,  
these speakers should be placed between them.  
The ambient surround speakers should be placed higher than the seating  
area, at least two feet (0.6 meter) above (seated) ear level (see Figure 4).  
The preferred method to mount the ambient surrounds is to put them directly in  
the side walls. This lets each speaker radiate to the front and back of the room  
and to reflect off the side walls.  
There are a few instances in which the ambient surrounds would perform  
better if mounted in the ceiling rather than the walls. If one or both of the walls  
are “acoustically dead,due to the presence of windows, fabric, furniture or  
other absorption, it may be necessary to turn the ambient speakers sideways  
and, instead of mounting them in a vertical orientation, mount them in the  
ceiling in a horizontal orientation.  
Figure 4.  
L
C
R
6.1-CHANNEL SYSTEMS  
A 6.1-channel system can be thought of as a 5.1-channel system with the  
addition of a rear center speaker placed midway between the two surround  
speakers, and further to the rear than the surrounds. It should be placed at the  
same height as the side surround speakers (see Figure 5).  
FLOOR PLAN  
Figure 5. 6.1-Channel system  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPEAKER PLACEMENT  
L
C
R
7.1-CHANNEL SYSTEMS  
In a 7.1-channel system, two speakers are added for rear fill, in addition to the sur-  
round speakers in a 5.1-channel system. The two additional speakers are placed on  
the rear wall or near the rear wall in the ceiling (see Figure 6).  
SIDE  
LEFT  
SIDE  
RIGHT  
REAR RIGHT  
REAR LEFT  
Figure 6. 7.1-Channel system  
CONNECTING THE SPEAKERS TO THE REST OF YOUR SYSTEM  
To connect the Synthesis Three Array loudspeakers to the power amplifiers or receiver, use two-conductor insulated  
speaker wire. We recommend #14 AWG wire as a minimum size. Your JBL dealer can recommend suitable cables.  
Both the SAM3VA and SAM3HA utilize 5-way binding posts that can accommodate up to #10 AWG stranded wire.  
PREPARING THE HOOKUP WIRE  
1. First determine the distance between your amplifier and the most distant speaker in each group (fronts, surrounds,  
back surrounds, subwoofers).  
2. Now make the hookup wires for all speakers in each group this length, even if one speaker is much closer to your  
amplifier than the other. This will help maintain proper signal balance.  
3. Strip off 3/8" (10mm) of insulation from both ends of each conductor.  
4. Twist each set of standard wires into a tightly bunched spiral.  
5. Speakers and electronics terminals have corresponding (+) and (–) terminals. Most manufacturers of speakers and  
electronics, including JBL, use red to denote the (+) terminal and black for the (–) terminal, although some elec-  
tronics manufacturers have adopted the new color-coding standard promulgated by the Consumer Electronics  
Association. In that case, the positive terminal will be colored to correspond to the channel position, while the  
negative terminal will be black.  
It is important to connect all speakers identically: (+) on the speaker to (+) on the amplifier and (–) on the speaker to  
(–) on the amplifier. Wiring “out of phase” results in thin sound, weak bass and poor imaging.  
With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the cor-  
rect polarity remains equally important to preserve the proper ambience and directionality of the program material.  
Now find a visual difference between the two conductors of each molded pair of speaker wires. Differentiating  
marks can be a different color wire (copper or silver); a strand of yarn in one conductor; thin, raised ribs on one part  
of the outer insulation; or a printed marking on one part of the outer insulation. It doesn’t matter which of the two  
strands go to the (+) and (–) on the speakers and amplifiers, as long as all speakers are connected identically. Push  
down on the binding post, insert the wire into the hole, and release.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING THE SPEAKERS TO THE REST OF YOUR SYSTEM  
Figure 7. Synthesis Three Array with powered subwoofers  
SDP-5  
SDP-5 Digital Surround Processor/Controller  
INPUTS  
NOTE: Although the  
SDP-5 is shown here,  
connections for the  
SDP-40 are similar.  
MAIN  
ZONE  
2
JBL, Inc. Northridge, CA  
Assembled in USA  
S/PDIF INPUTS  
2
1
3
2
4
TUV  
INPUT  
1
INPUT  
2
Y
Y
PR  
PR  
PB  
PB  
Y
Y
PR  
PR  
PB  
PB  
C
US  
1
1
1
2
2
3
4
4
5
5
VIDEO  
VIDEO  
AUDIO  
CAUTION  
S/N  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
ATTENTION  
RISQUE DE CHOC  
ELECTRIQUE  
3
4
NE PAS OUVRIR  
OUTPUT  
CENTER  
INPUT  
7
3
IR IN  
3
6
8
FRONT  
SIDE  
REAR  
TRIGGER  
OUTPUTS  
(L)  
(R)  
(C)  
(LS)  
(RS)  
(L)  
(R)  
(C)  
(LS)  
(RS)  
L
L
L
S/PDIF  
OUT  
1
2
RS-232  
(SUB)  
(SUB)  
R
R
R
SUBWOOFER  
OUTPUTS  
1
2
AC 100-240V ~ 50-60 HZ, 60W  
SDEC-3000  
INPUT CHANNEL OUTPUT  
A1  
A2  
A3  
A4  
B1  
B2  
B3  
B4  
Left Front  
C1  
Right Front C2  
Center  
C3  
C4  
Left Side  
Right Side D1  
Left Rear D2  
Right Rear D3  
Subwoofer D4  
S7150  
NO USER SERVICEABLE PARTS INSIDE. REFER  
SERVICING TO QUALIFIED PERSONNEL  
INPUT  
JBL SYNTHESIS  
NORTHRIDGE, CA  
DESIGNED, ENGINEERED AND MANUFACTURED  
IN THE UNITED STATES OF AMERICA  
TRIGGERS  
IN  
S5160 POWER AMPLIFIER  
Ch. 1 Left Front  
Ch. 2 Right Front  
Ch. 3 Center  
Ch. 1  
Input  
Ch. 2  
Input  
Ch. 3  
Input  
Ch. 4  
Input  
Ch. 5  
Input  
Ch. 6  
Input  
Ch. 7  
Input  
SPKR-1  
SPKR-2  
OUT  
Ch. 4 Left Side  
Ch. 5 Right Side  
Ch. 6 Left Rear  
Ch. 7 Right Rear  
MANUAL  
ON  
AUTO  
ON  
ON  
15A  
120V  
~
50/60Hz  
1800W  
OFF  
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.  
ATTENTION:  
VOIR LE CAHIER D'  
INSTRUCTION  
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture  
+
+
+
+
+
+
+
-
-
-
-
-
-
-
serial number  
Ch. 1 Output  
Ch. 2 Output  
Ch. 3 Output  
Ch. 4 Output  
Ch. 5 Output  
Ch. 6 Output  
Ch. 7 Output  
Front  
Left  
Front  
Right  
Front  
Center  
Side  
Left  
Side  
Right  
Rear  
Left  
Rear  
Right  
To  
Subwoofers  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING THE SPEAKERS TO THE REST OF YOUR SYSTEM  
Figure 8. Synthesis Three Array with passive subwoofers  
SDP-5  
SDP-5 Digital Surround Processor/Controller  
INPUTS  
MAIN  
ZONE  
2
JBL, Inc. Northridge, CA  
Assembled in USA  
S/PDIF INPUTS  
2
1
3
2
4
TUV  
INPUT  
1
INPUT  
2
NOTE: Although the SDP-5  
is shown here, connections  
for the SDP-40 are similar.  
Y
Y
PR  
PR  
PB  
PB  
Y
Y
PR  
PR  
PB  
PB  
C
US  
1
1
1
2
2
3
3
4
4
5
5
VIDEO  
VIDEO  
AUDIO  
CAUTION  
S/N  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
ATTENTION  
RISQUE DE CHOC  
ELECTRIQUE  
3
4
NE PAS OUVRIR  
OUTPUT  
CENTER  
INPUT  
7
3
IR IN  
6
8
FRONT  
SIDE  
REAR  
TRIGGER  
OUTPUTS  
(L)  
(R)  
(C)  
(LS)  
(RS)  
(L)  
(R)  
(C)  
(LS)  
(RS)  
L
L
L
S/PDIF  
OUT  
1
2
RS-232  
(SUB)  
(SUB)  
R
R
R
SUBWOOFER  
OUTPUTS  
1
2
AC 100-240V ~ 50-60 HZ, 60W  
SDEC-3000  
INPUT CHANNEL OUTPUT  
A1  
A2  
A3  
A4  
B1  
B2  
B3  
B4  
Left Front  
C1  
Right Front C2  
Center  
C3  
C4  
Left Side  
Right Side D1  
Left Rear D2  
Right Rear D3  
Subwoofer D4  
S7150  
JBL SYNTHESIS  
NORTHRIDGE, CA  
NO USER SERVICEABLE PARTS INSIDE. REFER  
SERVICING TO QUALIFIED PERSONNEL  
DESIGNED, ENGINEERED AND MANUFACTURED  
IN THE UNITED STTES OF AMERICA  
TRIGGERS  
IN  
S5160 POWER AMPLIFIER  
INPUT  
Ch. 1  
Input  
Ch. 2  
Input  
Ch. 3  
Input  
Ch. 4  
Input  
Ch. 5  
Input  
Ch. 6  
Input  
Ch. 7  
Input  
Ch. 1 Left Front  
Ch. 2 Right Front  
Ch. 3 Center  
SPKR-1  
SPKR-2  
OUT  
MANUAL  
ON  
AUTO  
ON  
Ch. 4 Left Side  
Ch. 5 Right Side  
Ch. 6 Left Rear  
Ch. 7 Right Rear  
ON  
15A  
120V  
50/60Hz  
1800W  
~
OFF  
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.  
ATTENTION:  
VOIR LE CAHIER D'  
INSTRUCTION  
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture  
+
+
+
+
+
+
+
-
-
-
-
-
-
-
serial number  
Ch. 1 Output  
Ch. 2 Output  
Ch. 3 Output  
Ch. 4 Output  
Ch. 5 Output  
Ch. 6 Output  
Ch. 7 Output  
S800  
VOIR LE CAHIER D'  
INSTRUCTION  
JBL SYNTHESIS  
NORTHRIDGE, CA  
DESIGNED, ENGINEERED AND MANUFACTURED  
IN THE UNITED STATES OF AMERICA  
ATTENTION:  
TRIGGERS  
IN  
S800 POWER AMPLIFIER  
Ch. 1 Left Sub  
Ch. 2 Right Sub  
BRIDGED  
Ch. 1  
BRIDGED  
Input  
Ch. 2  
Input  
WARNING; To reduce the risk of fire or  
electric shock, do not expose  
MONO  
STEREO  
this appliance to rain or moisture  
OUT  
No user serviceable parts inside. Refer  
servicing to qualified personnel.  
AUTO  
ON  
MANUAL  
ON  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
AVIS:  
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR  
ON  
10A  
120V  
50/60Hz  
1200W  
~
OFF  
HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.  
WARNING:  
serial number  
BRIDGED  
+
+
-
+
-
-
Ch. 1 Output  
Ch. 2 Output  
To Left To Right  
Sub Sub  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
SYMPTOM  
PROBABLE CAUSE  
SOLUTION  
No sound coming  
from speaker  
• Amplifier not turned on  
• Amplifier gain is low  
Turn on amplifier.  
Make sure that there is  
amplifier gain for that channel.  
• Correct source not  
selected or turned on  
Select proper source.  
• Defective patch cords to amplifier  
Check/replace patch cords.  
• Speaker wires not  
connected to amplifier  
Check speaker wire  
connection to amplifier.  
• Balance control set improperly  
Make sure Balance control is set  
at center, or 12 o’clock, position.  
• Speaker wires damaged  
or shorted  
Make sure none of the speaker wires  
are frayed, cut or punctured. Make sure  
no wires are touching other wires or  
terminals and creating a short circuit.  
®
®
• Speaker not configured  
correctly  
In Dolby Digital or DTS mode, make  
sure that the receiver/processor is  
configured so that the speaker in  
question is enabled.  
®
• Center speaker is configured  
incorrectly  
In Dolby Pro Logic mode, make sure the  
center speaker is not in phantom mode.  
• Problem not diagnosed  
To diagnose the likely source of the  
problem, it is often helpful to switch the  
nonfunctioning speaker with one that  
is functioning correctly. Turn off all  
electronics before exchanging the  
speakers. Turn everything back on, and  
determine whether the problem is in  
the same place, or has moved with the  
speaker. If the problem is in the same  
place, the source is most likely with your  
receiver or amplifier. If the problem has  
followed the speaker, then contact your  
authorized JBL Synthesis custom installer  
or dealer for further assistance. If that  
is not possible, visit our Web site at  
Bass is very weak  
• Subwoofers are wired out  
of phase  
Make sure that positive terminals on the  
subwoofers go to the positive terminals  
on the amplifiers (red) and do the same  
for the negatives.  
• Subwoofers have not  
been placed optimally  
Experiment with different locations.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
SAM3HA  
SAM3VA  
ULTRAHIGH-FREQUENCY DRIVER  
HIGH-FREQUENCY TRANSDUCER  
045TI 1" (25MM) PURE-TITANIUM COMPRESSION  
DRIVER WITH ALUMINUM EDGE-WOUND VOICE COIL  
AND 2" (51MM) NEODYMIUM MOTOR ASSEMBLY,  
MOUNTED IN A CONSTANT-DIRECTIVITY HORN  
045TI 1" (25MM) PURE-TITANIUM COMPRESSION  
DRIVER WITH ALUMINUM EDGE-WOUND VOICE COIL  
AND 2" (51MM) NEODYMIUM MOTOR ASSEMBLY,  
MOUNTED IN A CONSTANT-DIRECTIVITY HORN  
175ND-3 1-3/4" (44MM) AQUAPLAS-TREATED  
ALUMINUM-DOME COMPRESSION DRIVER WITH  
ALUMINUM EDGE-WOUND VOICE COIL AND NEODYMIUM  
MOTOR ASSEMBLY, MOUNTED IN A VERTICAL  
CONSTANT-DIRECTIVITY HORN  
175ND-3 1-3/4" (44MM) AQUAPLAS-TREATED  
ALUMINUM-DOME COMPRESSION DRIVER WITH  
ALUMINUM EDGE-WOUND VOICE COIL AND NEODYMIUM  
MOTOR ASSEMBLY, MOUNTED IN A VERTICAL  
CONSTANT-DIRECTIVITY HORN  
LOW-FREQUENCY TRANSDUCER  
6-1/2" (165MM) DEEP-ANODIZED CONE AND DOME  
MATERIAL WITH DUAL INSIDENEODYMIUM  
MAGNETS, SHIELDED MOTOR STRUCTURE AND 2"  
(51MM) VOICE COILS  
6-1/2" (165MM) DEEP-ANODIZED CONE AND DOME  
MATERIAL WITH DUAL INSIDENEODYMIUM  
MAGNETS, SHIELDED MOTOR STRUCTURE AND 2"  
(51MM) VOICE COILS  
SENSITIVITY (2.83V/1M)  
89DB  
89DB  
FREQUENCY RESPONSE (–3DB)  
48HZ TO 40KHZ  
200 WATTS  
48HZ TO 40KHZ  
200 WATTS  
MAXIMUM RECOMMENDED  
AMPLIFIER POWER  
CROSSOVER FREQUENCIES  
1KHZ, 10KHZ  
6 OHMS  
1KHZ, 10KHZ  
6 OHMS  
NOMINAL IMPEDANCE  
DIMENSIONS (H X W X D)  
9-5/8" X 28-5/8" X 9-1/16"*  
(244MM X 727MM X 230MM)  
27-3/8" X 10-3/16" X 12-5/8"*  
(695MM X 259MM X 321MM)  
WEIGHT PER SPEAKER  
31 LB (14KG)  
34 LB (15.5KG)  
* Note: Dimensions do not include mounting hardware or feet. Add 1" (25mm) height for feet.  
All features and specifications are subject to change without notice.  
JBL, JBL Synthesis and Synthesis are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries.  
Array, Symmetrical Field Geometry and Vented Gap Cooling are trademarks of Harman International Industries, Incorporated.  
THX is a registered trademark, and THX Ultra2 is a trademark, of THX Ltd. All rights reserved.  
SACD is a trademark of Sony Corporation.  
Dolby and Pro Logic are registered trademarks of Dolby Laboratories.  
DTS is a registered trademark of DTS, Inc.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Declaration of Conformity  
We, Harman Consumer Group International  
2, route de Tours  
72500 Château du Loir  
France  
declare in own responsibility that the products described  
in this owner’s manual are in compliance with technical  
standards:  
Harman Consumer Group, Inc.  
250 Crossways Park Drive  
Woodbury, NY 11797  
EN 61000-6-3:2001  
EN 61000-6-1:2001  
8500 Balboa Boulevard  
Northridge, CA 91329  
818.830.8757  
Luc Guillaume  
Harman Consumer Group International  
Château du Loir, France 9/06  
Part No. 301227-001 9/06  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Insignia DVD Player NS 8PDVD User Manual
Jacuzzi Hot Tub EA20 User Manual
Jet Tools Saw JPS 10 User Manual
JVC Home Theater System NX BD3 User Manual
JVC Network Card AA V31E User Manual
JVC Stereo Receiver 1105RYMMDWJEIN User Manual
Kenwood Convection Oven BM250 User Manual
Keys Fitness Home Gym ST RC User Manual
KitchenAid Clothes Dryer 86 User Manual
Korg Electronic Keyboard N264 76 User Manual