Invacare Hot Tub 2001 User Manual

Heavy Duty Cleaning Procedure  
Maintenance Instructions  
For Invacare Continuing Care Group Tubs  
SAVE THESE INSTRUCTIONS  
WARNING  
DO NOT use this product or any available optional equipment without first completely reading and understanding these  
instructions and any additional instructional material such as owner’s manuals, service manuals or instruction sheets supplied  
with this product or optional equipment. If you are unable to understand the warnings, cautions or instructions, contact a  
healthcare professional, dealer or technical personnel before attempting to use this equipment - otherwise, injury or damage may  
occur.  
The disinfectant dispensing system has been factory tested and calibrated for use with Invacare disinfectant. The use of any disinfectant  
with a dilution ratio (½ oz. per gallon) or viscosity level different than that of Invacare disinfectant will result in an improper mixture of  
disinfectant and water. This may cause your system to be improperly disinfected - or in some instances, not disinfected at all. If using  
any disinfectant with a dilution ratio or viscosity level different than that of Invacare disinfectant or if switching from one type of  
disinfectant to another type, the disinfectant flowmeter must be calibrated before performing this procedure. Refer to the tub owner’s  
manual or to the calibration instruction sheet, part number 1154272, for the calibration procedure.  
ALWAYS wear rubber gloves, an apron and face shield protection during disinfecting, cleaning and rinsing procedures. In case of  
eye or skin contact, follow procedures on disinfectant container.  
CAUTION  
NEVER use abrasive cleaners like scouring powder or liquid cleaners containing pumice stone. The use of these types of cleaners  
®
will make the gel-coat finish of your tub scratched and dull. NEVER use cleaners containing iodine, bromine, Betadine or  
methylene blue. The use of these types of cleaners will cause the tub to stain. Never use cleaners containing bleach. Use of these  
types of cleaners will dry out the rubber seals and gaskets and the tub will not function properly.  
Before starting the whirlpool pump, the water level must be completely above the whirlpool jets. Otherwise damage to the  
motor/pump will result.  
Heavy Duty Cleaning Procedure  
TUB  
MODEL  
NUMBER  
WATER REQUIRED  
TO COVER JETS  
(GALLONS)  
INVACARE  
HEAVY DUTY  
CLEANER  
REQUIRED (OZ)*  
In addition to disinfecting your tub after every use, you will need to perform this procedure  
approximately once every 80150 baths.  
1. Clean the entire surface of the tub to remove visible tissue residue and fluid.  
2. Rinse the inside surface of the tub with the shower/massage wand on the spray setting.  
3. Rotate the water temperature valve to adjust the water temperature to approximately  
2800  
2001  
3700  
3750  
3800  
3600  
3650  
3600XL  
2300  
3300  
4300  
4300HL  
5300  
5300HL  
6300  
6300ADH  
4400SS  
5400SS  
10  
32  
30  
30  
30  
30  
48  
48  
25  
30  
35  
35  
52  
52  
50  
50  
48  
50  
40  
128  
120  
120  
120  
120  
192  
192  
100  
120  
140  
140  
208  
208  
200  
200  
192  
200  
o
105 F.  
NOTE: This will maximize the cleaning solutionʹs ability to clean and disinfect the system.  
4. Close the drain.  
5. Make sure the whirlpool jets are open.  
6. Fill the tub one inch above the highest whirlpool jets.  
7. Add the Invacare Heavy Duty Cleaner to the water in the tub. Refer to the chart for the  
proper amount.  
8. Spray premixed Invacare Heavy Duty Cleaner on the remaining surfaces.  
9. Press the whirlpool on/off button to turn on the whirlpool pump and let the pump run  
for 60 seconds.  
10. Turn off the pump and allow the heavy duty cleaner/water solution to remain in the tub  
for 10 minutes.  
11. During this tenminute waiting time, take a long handled brush and thoroughly scrub  
all interior surfaces of the tub.  
12. Open the drain to allow the heavy duty/water solution to drain from the tub.  
13. Use the shower/massage wand on the pulse setting and direct the spray into both  
whirlpool jets to back flush until the water discharging from the whirlpool inlet is clear.  
*NOTE: If using nonInvacare heavy duty  
cleaner, refer to the instructions supplied with the  
cleaner to determine the proper amount required.  
14. Rinse the tub thoroughly with the shower wand on the spray setting.  
15. Check the tub for damage and to ensure all surfaces of the tub are clean and that no  
visible residue remains. If residue is found, repeat STEPS 13 and 14.  
Invacare Continuing Care Group  
USA  
Canada  
One Invacare Way  
Elyria, Ohio USA  
44036-2125  
994 Hargrieve Rd.  
London Ontario  
N6E IP5 Canada  
All rights reserved. Trademarks are identified by the symbols ™ and ®. All  
trademarks are owned by or licensed to Invacare Corporation unless  
otherwise noted.  
Betadine is a registered trademark of Purdue Pharma L.P.  
© 2008 Invacare Corporation  
Part No 1154271  
Rev A - 04/08  
For customer service call: 800-668-2337  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ingersoll Rand Heat Pump 650752 User Manual
Ingersoll Rand Water Pump PM10X X X A02 User Manual
JVC Computer Monitor 0110SKH MW MT User Manual
Karcher Pressure Washer K 240 User Manual
Kensington Computer Accessories K62065A User Manual
Kenwood Marine Radio TKR 740 User Manual
King Canada Planer KC 520C User Manual
KitchenAid Range KERS205 User Manual
KitchenAid Washer KAWE977D User Manual
Kodak Digital Camera C310 CD40 User Manual