Intel Computer Hardware 915GM User Manual

Intel® Embedded Compact Extended  
Form Factor  
Proof-of-Concept Board  
Based on Intel® 915GM Chipset  
User’s Manual  
June 2007  
Order Number: 310915-002  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Contents  
1
Product Overview............................................................................................................5  
1.1  
1.2  
1.3  
1.4  
1.5  
Introduction...........................................................................................................5  
Related Documents...............................................................................................5  
Product Contents ..................................................................................................6  
Proof-of-Concept Board Features..........................................................................6  
Intel® ECX Form Factor POC Board Based on Intel® 915GM Chipset Block  
Diagram................................................................................................................8  
2
3
Installation Guide for POC Board ...................................................................................9  
2.1  
2.2  
Before You Begin..................................................................................................9  
Setting up the Intel® ECX POC Board...................................................................9  
Connectors and Jumpers..............................................................................................14  
3.1  
3.2  
List of Jumpers....................................................................................................15  
List of Connectors...............................................................................................17  
Figures  
Tables  
Figure 1. Block Diagram ....................................................................................................8  
Figure 2. Assembly board, Top View................................................................................11  
Figure 3. Assembly board, Bottom View...........................................................................11  
Figure 4. 20-pin Power Supply Connector........................................................................12  
Figure 5. Connectors and Jumpers ..................................................................................14  
Figure 6. Solder Side.......................................................................................................15  
Table 1. Related Documents..............................................................................................5  
Table 2. Additional Hardware.............................................................................................9  
Table 3. Jumper Settings.................................................................................................10  
Table 4. Jumpers.............................................................................................................15  
Table 5. Compact Flash Power Select (JP1)...................................................................16  
Table 6. LVDS Voltage select (JP2)................................................................................16  
Table 7. COM1 Mode Select for RS-232/422/485 (JP3/JP6/JP7) ....................................16  
Table 8. COM1 Mode Select (JP4)...................................................................................16  
Table 9. COM2 Mode Select (JP5)...................................................................................16  
Table 10. CMOS Clear Jumper (JP8)...............................................................................16  
Table 11. Audio Output Select Jumper (JP9)....................................................................16  
Table 12. Connectors ......................................................................................................17  
Table 13. Digital I/O Connector (CN1)..............................................................................17  
Table 14. Front Panel Bezel Connector (CN2) .................................................................17  
Table 15. Primary IDE Hard Drive Connector (CN3).........................................................18  
Table 16. Parallel Port Connector (CN4)..........................................................................18  
Table 17. USB Port2 & Port3 Connector (CN5)................................................................19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Table 18. LVDS Connector (CN6)....................................................................................19  
Table 19. Power Connector (CN7) ...................................................................................19  
Table 20. LVDS Voltage Connector (CN8) .......................................................................19  
Table 21. Serial Port2 Connector (CN9)...........................................................................20  
Table 22. LAN Connector (CN10) ....................................................................................20  
Table 23. Audio Connector (CN11) ..................................................................................20  
Table 24. USB Port0 & Port1 Connector (CN12)..............................................................20  
Table 25. 6-Pin Mini Dim Keyboard/Mouse Connector (CN13) .........................................20  
Table 26. TV-OUT Connector (CN14)..............................................................................21  
Table 27. Serial Port1 Connector (CN15).........................................................................21  
Table 28. VGA Connector (CN16)....................................................................................21  
Table 29. SATA Connector (CN17)..................................................................................21  
Table 30. FDD Connector (CN18)....................................................................................22  
Table 31. Compact Flash Connector (CN19)...................................................................22  
Table 32. Fan Connector (FAN1).....................................................................................23  
Revision History  
Date  
Revision  
Description  
June 2007  
002  
001  
Added disclaimer  
January 2006  
Initial public release  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product Overview  
1
Product Overview  
1.1  
Introduction  
The Proof of Concept board utilizes the Intel® Pentium® M Processor Low Voltage 738 or  
Intel® Celeron® M Processor Ultra Low Voltage 373, and the Intel® 915GM and Intel® I/O  
Controller Hub 6-M (ICH6-M) chipset. It is a fanless design which provides higher  
processing capability with excellent power consumption control. It offers a stable and  
efficient solution for customer who is seeking a trade-off between high performance and  
low power consumption. The POC board supports multiple display modes including CRT,  
LCD and TV-out. With the dimension of 146mm X 105mm, Intel® Embedded Compact  
Extended Form Factor also has the expansion capability through on-board Mini-PCI Type  
3-B slot.  
1.2  
Related Documents  
For more information, please contact your Intel local representative.  
Table 1. Related Documents  
Intel Order  
Number  
Document  
Location  
Intel® Pentium® M Processor on 90 nm  
Process with 2-MB L2 Cache Datasheet  
Intel® Pentium® M Processor on 90 nm  
Process with 2-MB L2 Cache Specification  
Update  
tashts/302189.htm  
302189  
ecupdt/302209.htm  
302209  
Intel® Celeron® M Processor on 90 nm  
Process Datasheet  
Intel® Celeron® M Processors Specification  
Update  
tashts/303110.htm  
ecupdt/300303.htm  
303110  
300303  
305264  
307167  
301473  
301474  
Mobile Intel® 915PM/GM/GMS and 910GML  
Express Chipset Datasheet  
Mobile Intel® 915GM/PM/GMS and 910GML  
Express Chipset Specification Update  
Intel® I/O Controller Hub 6 (ICH6) Family  
Datasheet  
tashts/305264.htm  
ecupdt/307167.htm  
datashts/301473.htm  
specupdt/301474.htm  
Intel® I/O Controller Hub 6 (ICH6) Family  
Specification Update  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product Overview  
1.3  
1.4  
Product Contents  
The Intel® ECX Form Factor POC board based on Intel® 915GM chipset is shipped with  
the following peripherals:  
y
y
One POC board with two heat sinks – one for the CPU and one for the GMCH  
15 Jumper caps  
Proof-of-Concept Board Features  
The proof-of-concept board features are summarized as below:  
System:  
y
CPU (Onboard 479-ball µFCBGA) supported:  
-
Intel® Pentium® M Processor Low Voltage 738 or  
-
Intel® Celeron® M Processor Ultra Low Voltage 373 (default)  
y
y
y
y
Memory supported:  
200-pin DDR2 400MHz SODIMM x 1, Max. 1GB  
Chipset :  
-
-
Intel® 915GM GMCH + Intel® 82801 FBM (ICH6-M)  
Super I/O:  
-
W83627HF  
Ethernet  
-
-
-
FAST Ethernet with Intel® 82551QM (default)  
Gigabit Ethernet with Intel® 82541ER (optional)  
On board RJ-45 interface  
y
Extension Slot (140 pins AMP connector):  
-
-
-
-
SDVO x1  
LPC x1  
PCI Master x2  
PCI Express x1  
y
y
BIOS :  
-
Phoenix-Award 4Mbit FLASH ROM  
Watchdog Timer :  
-
255 levels as SMI  
-
Reset from 0~255 seconds controlled by W83627HF  
y
y
y
y
y
Battery :  
-
Lithium battery  
Power Supply Voltage :  
-
5/12V. AT/ATX  
Board Size :  
-
146mm x 105mm  
Gross Weight :  
-
0.55lb(0.4kg)  
Operating Temperature :  
-
32ºF~140ºF (0ºC~60ºC)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product Overview  
Display:  
y
Analog CRT DAC interface support  
-
-
-
24-bit RAMDAC support (8-bit for each RGB signal DAC)  
Resolution up to 2048 x 1536 at 75Hz  
DDC2B compliant  
y
y
Analog TV-Out interface support  
On board S-Video 4-pin mini DIN connector  
Dedicated Local Flat Panel(LFP) LVDS interface  
-
-
Compliant with ANSI/TIA/EIA-644-2001 spec  
-
Supports 25 to 112 MHz single/dual channel LVDS interface with Spread  
Spectrum Clocking (SSC)  
-
Support TFT panel type with maximum pixel format of 1x18 bpp for single channel  
and 2x18 bpp for dual channels  
-
-
Maximum Panel size supported up to UXGA  
Maximum Wide Panel size supported up to WUXGA  
y
y
y
SDVO support through Extension Slot  
-
Two SDVO ports are supported  
-
Supports a variety display devices such as DVI, TV Out, LVDS, etc  
Dual display support  
-
-
Independent: different images and native display timings on each display device  
Simultaneous: same images and native display timings on each display device  
Dynamic Video Memory Technology (DVMT) 3.0 to dynamically allocate up to 128 MB  
of system memory for graphics usage  
I/O:  
y
Storage :  
-
-
-
-
Integrated IDE controller support PIO IDE and Ultra ATA 100/66/33  
One SATA ports support data transfer rate up to 1.5Gb/s (150 MB/s)  
Support Advanced Host Controller Interface (AHCI)  
Type I/II CompactFlash* slot x 1  
y
y
y
Keyboard  
PS/2 Mouse  
Audio :  
-
-
-
Realtek ALC202A AC’97 codec audio  
Amplifier for speaker-out with 2.5 W for each channel  
MIC-in, Line-in, Line-out/Speaker-out (jumper selectable)  
y
USB :  
-
USB 2.0 ports x2  
-
USB 2.0 on pins header x2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product Overview  
1.5  
Intel® ECX Form Factor POC Board Based on Intel® 915GM  
Chipset Block Diagram  
Figure 1. Block Diagram  
Intel® Pentium® M LV 738  
or  
CK-410  
DC/DC IMVP IV  
Intel® Celeron® M ULV 373  
Processor  
CK-SSCD  
DC-DC GMCH, DDR2  
479 uPCBCA  
FSB 400  
LVDS  
DDR2  
SO-DIMM  
Intel® 915GM  
DDR2 400  
SDV0  
VGA  
GMCH  
TVOUT  
1257 FCBCA  
DMI  
SATA x 1  
PATA, CF  
PCI-E  
Extension  
Slot  
Intel® 82801FBM  
ICH6-M  
Intel® 82551 QM/  
USB 2.0  
X 4  
33MHz PCI  
Intel® 82541 ER  
RJ-45  
1257 FCBCA  
LPC  
10/100/1000  
AC’97  
CODEC  
Super I/O  
W83627HF  
FWH  
COM1,2  
LPT  
KB/MS  
FLOPPY  
D I/O  
B5581-01  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Guide for POC Board  
2
Installation Guide for POC Board  
2.1  
Before You Begin  
Table 2 shows the additional hardware that may be needed to set up the board.  
Table 2. Additional Hardware  
Component  
VGA Monitor  
Keyboard  
Description  
Standard VGA or greater resolution monitor.  
Keyboard with a PS/2 connector or adapter.  
Mouse with a PS/2 connector or adapter.  
Mouse  
IDE Devices  
Up to two IDE devices can be connected to the POC board. One  
cable is included in this kit. The cable accommodates the included  
hard drive and one other IDE device, such as a CD-ROM drive or  
another hard drive.  
Network Adapter  
An Intel® 82551 QM Ethernet Controller is included in the  
development kit. A CAT-5 cable with an RJ-45 connector is  
required to connect this Ethernet adapter to local area network.  
AT Power Supply An AT power supply is required in order to power up the board. If  
you are using an ATX power supply see Section 2.2 for details on  
how to make ATX work.  
Memory  
One module of 200-pin DDR2 400 MHz SODIMM (max 1 GByte) is  
required.  
Other Devices  
and Adapters  
Many PC-compatible peripherals can be attached and configured to  
work with the POC board. For example, installing an additional  
network adapter into the mini PCI slot. Procuring and installing any  
drivers required for additional devices will need to be done by user.  
2.2  
Setting up the Intel® ECX POC Board  
Gather the hardware described in section 2.1 and follow the steps below to set up the POC  
board. This manual assumes the user is familiar with basic concepts of installing and  
configuring hardware for an x86 architecture platform.  
1. Ensure a static free work environment. Static-free procedures must be completed  
before removing any components from various anti-static packaging. The POC board  
is susceptible to electrostatic discharge (ESD), which may cause product failure or  
unpredictable operation.  
Caution: Connecting the wrong cable or reversing a cable may damage the POC board and may  
damage the device being connected. Since the board is not in a protective chassis, use caution  
when connecting cables to this product.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Guide for POC Board  
2. Verify contents. Inspect the contents of your kit, and ensure that everything listed in  
Section 1.3 is included. Check for damage that may have occurred during shipment.  
3. Check jumper settings. Verify that the following jumpers are set in their default state  
(see Table 3).  
Table 3. Jumper Settings  
Jumper  
J1  
Function  
Compact Flash Power Select  
LVDS Voltage select  
Default Setting  
3.3 V : Short 1-2  
J2  
3.3 V : Short 1-2  
J3  
COM1 Mode Select  
RS-232 : Short 3-5,4-6  
CN15 Pin 1  
DCD : Short 3-5  
RI : Short 4-6  
J4  
J5  
COM1 Mode Select  
COM2 Mode Select  
CN15 Pin 8  
CN15 Pin 1  
CN15 Pin 8  
DCD : Short 3-5  
RI : Short 4-6  
J6  
J7  
J8  
J9  
COM1 Mode Select  
COM1 Mode Select  
Clear CMOS Setting  
RS-232 : Short 3-5,4-6  
RS-232 : Short 1-2  
Normal : Short 1-2  
Line Out : Short 1-3, 2-4  
Audio Line Out/Speaker Out  
4. Verify installed hardware. Make sure the following hardware is populated on your  
POC board:  
One on-board Intel Intel® Celeron® M Processor Ultra Low Voltage 373 processor in  
the 479-ball µFCBGA package  
BIOS FWH  
Battery  
Heatsink  
Note:  
The above hardware should have been correctly installed at the factory. If they are not  
installed correctly, DO NOT power on the board. Correctly re-install the components before  
proceeding.  
5. Install memory. Install the SODIMM in memory slot DIMM1. Insert the SODIMM  
above the slot (the DIMM is keyed so that it only fits in the slot in one orientation).  
Firmly, but carefully, insert the SODIMM into the slot until the tabs close.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Guide for POC Board  
Figure 2. Assembly board, Top View  
Figure 3. Assembly board, Bottom View  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Guide for POC Board  
6. Install storage devices. There is one IDE and one SATA connector on the POC  
board, which supports up to 3 hard drives (two PATA IDE devices—a master and a  
slave and one SATA IDE device.  
Note:  
Master/slave settings are determined by a jumper on each IDE device. Consult the device  
label/documentation to verify that the jumper is set correctly for the configuration you  
choose. A CD-ROM drive or additional hard drive may be installed as a primary slave  
device.  
Warning:  
Failure to properly align the IDE cable may damage the POC board and/or the hard drive.  
7. Install the CD-ROM drive  
a) Verify that the jumper on the CD-ROM drive is set for slave.  
b) Connect the unused end of the IDE cable you have already attached to the  
POC board to the CD-ROM drive. Ensure that the cable tracer is aligned with  
pin 1 of the CD-ROM drive connector.  
c) Connect the four-pin power connector from the power supply to the CD-ROM  
drive.  
8. Connect the monitor. Connect the monitor cable to the VGA port.  
9. Connect the keyboard and mouse. Connect the KB/Mouse cable to the Mini-DIN  
PS/2 connector CN13 on the board. Then connect a PS/2 mouse and keyboard to the  
KB/Mouse cable. Alternatively, USB keyboard and a USB mouse may be plugged into  
one or both of the USB connectors (CN12) on the board. Note that a legacy (PS/2)  
keyboard is needed to for entering BIOS setup mode.  
Note:  
If you connect the USB keyboard and USB mouse to the front panel, you must connect the  
USB cable from the front panel to the connector CN5 on the board first.  
10. Connect the power supply. Make sure the power supply is turned off and unplugged.  
Connect the AT 4P power supply cables to connector CN7 on the board. Next, plug the  
power cord into the power supply on the wall.  
11. Power up the system. Turn on the monitor and follow by the power supply. Please  
refer to Table 19: CN7 for the power supply pin configuration and tap it from ATX  
power supply.  
Warning:  
A loose jumper wire could lead to intermittent power which could damage the board or  
cause an electrical short.  
Figure 4. 20-pin Power Supply Connector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Guide for POC Board  
Notes:  
Powering up without all components installed correctly could lead to a power-up failure that  
could damage that board. Do not power up the board until the source of any loose  
components is fixed and the component has been replaced on the board.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
3
Connectors and Jumpers  
This section describes the placement of the connectors as well as jumper settings on the  
board.  
Figure 5. Connectors and Jumpers  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
Figure 6. Solder Side  
3.1  
List of Jumpers  
Table 4 to Table 9 must be used in setting the jumpers on the POC board. These tables  
give details about the jumpers shown in Figure 5 and Figure 6. The jumpers allow  
configuring the system to user’s application. The table below shows the function of each of  
the board’s jumpers:  
Table 4. Jumpers  
Label  
J1  
Function  
Compact Flash Power Select  
LVDS Voltage select  
J2  
J3  
COM1 Mode Select  
CN15 Pin 1  
J4  
J5  
COM1 Mode Select  
COM2 Mode Select  
CN15 Pin 8  
CN15 Pin 1  
CN15 Pin 8  
J6  
J7  
J8  
J9  
COM1 Mode Select  
COM1 Mode Select  
Clear CMOS Setting  
Audio Line Out/Speaker Out  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
Table 5. Compact Flash Power Select (JP1)  
Option  
JP1  
3.3 V (default)  
5 V  
Short 1-2  
Short 2-3  
Table 6. LVDS Voltage select (JP2)  
Option JP2  
3.3 V (default)  
5 V  
Short 1-2  
Short 2-3  
Table 7. COM1 Mode Select for RS-232/422/485 (JP3/JP6/JP7)  
Option  
RS232 (default)  
RS422  
JP3  
JP6  
JP7  
Short 3-5, 4-6  
Short 1-3, 2-4  
Short 1-3, 2-4  
Short 3-5, 4-6  
Short 1-3, 2-4  
Short 1-3, 2-4  
Short 1-2  
Short 3-4, 7-8  
Short 5-6, 7-8  
RS485  
Table 8. COM1 Mode Select (JP4)  
Option  
JP4  
Pin 1=DCD (default)  
Pin 1=5 V  
Short 3-5  
Short 1-3  
Short 4-6  
Short 2-4  
Pin 8=RI (default)  
Pin 8=+12 V  
Table 9. COM2 Mode Select (JP5)  
Option  
JP5  
Pin 1=DCD (default)  
Pin 1=5 V  
Short 3-5  
Short 1-3  
Short 4-6  
Short 2-4  
Pin 8=RI (default)  
Pin 8=+12 V  
Table 10. CMOS Clear Jumper (JP8)  
Option  
Normal (default)  
Clear CMOS  
JP8  
Short 1-2  
Short 2-3  
Table 11. Audio Output Select Jumper (JP9)  
Option  
Line Out (default)  
Speaker Out  
JP8  
Short 1-3, 2-4  
Short 3-5, 4-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
3.2  
List of Connectors  
The board has a number of connectors configuring the system to user’s application. The  
table below shows the function of each board’s connectors:  
Table 12. Connectors  
Label  
CN1  
Function  
Digital I/O Connector  
CN2  
Front Panel Bezel Connector  
Primary IDE Hard Drive Connector  
Parallel Port Connector  
USB Port2 & Port3 Connector  
LVDS Connector  
CN3  
CN4  
CN5  
CN6  
CN7  
Power Connector  
CN8  
LVDS Voltage Connector  
Serial Port2 Connector  
LAN Connector  
CN9  
CN10  
CN11  
CN12  
CN13  
CN14  
CN15  
CN16  
CN17  
CN18  
CN19  
J1  
Audio Connector  
USB Port0 & Port1 Connector  
6-Pin Mini Dim Keyboard/Mouse Connector  
TV-OUT Connector  
Serial Port1 Connector  
VGA Connector  
SATA Connector  
FDD Connector  
Compact Flash Connector  
Extension SLOT  
FAN1  
FAN Connector  
SODIMM1 DDR2 SODIMM  
Table 13. Digital I/O Connector (CN1)  
Pin  
1
Signal  
Digital Input 1  
Digital Input 2  
GND  
Pin  
2
Signal  
Digital Output 1  
Digital Output 2  
Digital Output 3  
Digital Output 4  
3
4
5
6
7
GND  
8
Table 14. Front Panel Bezel Connector (CN2)  
Pin  
1
Signal  
Pin  
2
Signal  
System Power LED +  
GND  
External Speaker +  
Jumper Pin  
3
4
5
System Power LED -  
NC  
6
Jumper Pin  
7
8
External Speaker +  
Power On/Off  
9
Power On/Off GND  
System Reset GND  
Keyboard Lock GND  
HDD Activity LED -  
10  
12  
14  
16  
11  
13  
15  
System Reset  
Keyboard Lock  
HDD Activity LED +  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
Table 15. Primary IDE Hard Drive Connector (CN3)  
Pin  
1
Signal  
PRI_IDERST#  
PDD7  
Pin  
2
Signal  
GND  
3
4
PDD8  
PDD9  
PDD10  
PDD11  
PDD12  
PDD13  
PDD14  
PDD15  
NC  
5
PDD6  
6
7
PDD5  
8
9
PDD4  
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
32  
34  
36  
38  
40  
42  
44  
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
33  
35  
37  
39  
41  
43  
PDD3  
PDD2  
PDD1  
PDD0  
GND  
PDREQ  
PDIOW#  
PDIOR#  
PIORDY  
PDDACK#  
IRQ14  
GND  
GND  
GND  
GND  
GND  
NC  
PDA1  
P66DET  
PDA2  
PDCS#3  
GND  
PDA0  
PDCS#1  
IDEACTP#  
+5V  
+5V  
GND  
NC  
Table 16. Parallel Port Connector (CN4)  
Pin  
1
Signal  
Strobe #  
Data 0  
Pin  
2
Signal  
Auto Form Feed #  
Error #  
3
4
5
Data 1  
6
Initialize #  
Printer Select In #  
GND  
7
Data 2  
8
9
Data 3  
10  
12  
14  
16  
18  
20  
22  
24  
26  
11  
13  
15  
17  
19  
21  
23  
25  
Data 4  
GND  
Data 5  
GND  
Data 6  
GND  
Data 7  
GND  
Acknowledge #  
Busy  
GND  
GND  
Paper Empty #  
Printer Select  
GND  
NC  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
Table 17. USB Port2 & Port3 Connector (CN5)  
Pin  
1
Signal  
VCC  
D0-  
Pin  
2
Signal  
VCC  
D1-  
3
4
5
D0+  
6
D1+  
GND  
GND  
7
GND  
GND  
8
9
10  
Table 18. LVDS Connector (CN6)  
Pin  
1
Signal  
VCCM  
Pin  
2
Signal  
VCCM  
3
VCCM  
4
VCCM  
5
VCCM  
6
VCCM  
7
NC  
8
NC  
9
GND  
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
32  
34  
36  
38  
40  
GND  
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
33  
35  
37  
39  
LVDSB_D3-  
LVDSB_D3+  
GND  
LVDSB_D0-  
LVDSB_D0+  
GND  
LVDSB_CLK-  
LVDSB_CLK+  
GND  
LVDSB_D1-  
LVDSB_D1+  
GND  
LVDSA_D0-  
LVDSA_D0+  
GND  
LVDSB_D2-  
LVDSB_D2+  
GND  
LVDSA_D1-  
LVDSA_D1+  
GND  
LVDSA_D3-  
LVDSA_D3+  
GND  
LVDSA_D2-  
LVDSA_D2+  
GND  
LVDSA_CLK-  
LVDSA_CLK+  
GND  
Table 19. Power Connector (CN7)  
Pin  
1
Signal  
PS_ON  
GND  
NC  
Pin  
2
Signal  
GND  
+12 V  
5V SB  
5 V  
3
4
5
6
7
5 V  
8
9
NC  
10  
GND  
Table 20. LVDS Voltage Connector (CN8)  
Pin  
1
Signal  
12VM  
5V  
Pin  
2
Signal  
12VM  
ENAB  
GND  
3
4
5
GND  
GND  
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
Table 21. Serial Port2 Connector (CN9)  
Pin  
1
Signal  
Pin  
2
Signal  
Data Carrier Detect (DCD)  
Receive Data (RXD)  
Transmit Data (TXD)  
Data Terminal Ready (DTR)  
Ground (GND)  
Data Set Ready (DSR)  
Request to Send (RST)  
Clear to Send (CTS)  
Ring Indicator (RI)  
NC  
3
4
5
6
7
8
9
10  
Table 22. LAN Connector (CN10)  
Pin  
1
Signal  
TX+  
Pin  
2
Signal  
TX-  
3
RX+  
4
RJ45 Termination  
RX-  
5
RJ45 Termination  
RJ45 Termination  
6
7
8
RJ45 Termination  
Table 23. Audio Connector (CN11)  
Pin  
1
Signal  
Mic In  
Pin  
2
Signal  
GND  
GND  
GND  
GND  
GND  
3
Line In L  
Line In R  
Audio Out L  
Audio Out R  
4
5
6
7
8
9
10  
Table 24. USB Port0 & Port1 Connector (CN12)  
Pin  
1
Signal  
VCC  
Pin  
1
Signal  
VCC  
3
USB -  
USB +  
GND  
2
USB -  
USB +  
GND  
5
3
7
4
Table 25. 6-Pin Mini Dim Keyboard/Mouse Connector (CN13)  
Pin  
1
Signal  
Keyboard Data  
GND  
Pin  
2
Signal  
Mouse Data  
GND  
3
4
5
Keyboard Clock  
6
Mouse Clock  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
Table 26. TV-OUT Connector (CN14)  
Pin  
1
Signal  
Red  
Pin  
2
Signal  
Green  
NC  
3
Blue  
4
5
GND  
6
AGND  
7
AGND  
NC  
8
AGND  
9
10  
12  
14  
GND  
11  
13  
15  
NC  
DDC DAT  
Vertical Sync  
Horizontal Sync  
DDC CLK  
Table 27. Serial Port1 Connector (CN15)  
Pin  
1
Signal  
Pin  
2
Signal  
Data Carrier Detect (DCD)  
Transmit Data (RXD)  
GND  
Receive Data (RXD)  
Data Terminal Ready (DTR)  
Data Set Ready (DSR)  
Clear To Send (CTS)  
3
4
5
6
7
Request To Send (RTS)  
Ring Indicator (RI)  
8
9
Table 28. VGA Connector (CN16)  
Pin  
1
Signal  
Red  
Pin  
2
Signal  
Green  
3
Blue  
4
NC  
5
GND  
6
AGND  
7
AGND  
NC  
8
AGND  
9
10  
12  
14  
GND  
11  
13  
15  
NC  
DDC DAT  
Vertical Sync  
Horizontal Sync  
DDC CLK  
Table 29. SATA Connector (CN17)  
Pin  
1
Signal  
GND  
TX -  
Pin  
2
Signal  
TX +  
GND  
RX +  
3
4
5
RX -  
6
7
GND  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
Table 30. FDD Connector (CN18)  
Pin  
1
Signal  
5 V  
Pin  
2
Signal  
INDEX  
DRIVE0  
DSKCHG  
NC  
3
5 V  
4
5
5 V  
6
7
NC  
8
9
NC  
10  
12  
14  
16  
18  
20  
22  
24  
26  
MOTOR ON  
DIR  
11  
13  
15  
17  
19  
21  
23  
25  
NC  
HDSEL  
NC  
STEP  
WDATA  
WGATE  
TRK0  
GND  
GND  
GND  
GND  
GND  
WPT  
RDATA  
SIDE0  
Table 31. Compact Flash Connector (CN19)  
Pin  
1
Signal  
GND  
Pin  
2
Signal  
DATA 3  
DATA 5  
DATA 7  
Address 10  
Address 9  
Address 7  
Address 6  
Address 4  
Address 2  
Address 0  
DATA 1  
IOCS16#  
CD1-  
3
DATA 4  
DATA 6  
CS0#  
4
5
6
7
8
9
ATASEL  
Address 8  
VCC  
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
32  
34  
36  
38  
40  
42  
44  
46  
48  
50  
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
33  
35  
37  
39  
41  
43  
45  
47  
49  
Address 5  
Address 3  
Address 1  
DATA 0  
DATA 2  
CD2#  
DATA 11  
DATA 13  
DATA 15  
VS1#  
DATA 12  
DATA 14  
CS1#  
IORD#  
IOWR#  
INTR  
WE#  
VCC  
CSEL#  
VS2#  
RESET#  
DMAREQ  
DASP#  
DATA 8  
DATA 10  
IORDY#  
DMAACK-  
PDIAG#  
DATA 9  
GND  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors and Jumpers  
Table 32. Fan Connector (FAN1)  
Pin  
1
Signal  
GND  
Pin  
2
Signal  
12 V  
3
Sensor  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ingersoll Rand Heat Pump 670079 User Manual
Ingersoll Rand Water Pump 650632 X C User Manual
Integra Stereo Receiver DTR 55 User Manual
JBL Speaker PB8 User Manual
JVC Computer Monitor 0509SKH SW MT User Manual
JVC Home Theater System SP THS1F User Manual
JVC MP3 Player KD R820BT User Manual
JVC Satellite TV System HM DSR100RU User Manual
KitchenAid Clothes Dryer KEYE660W User Manual
Kramer Electronics Switch VS 66hdcp User Manual