Multi-Platform Tuner
TUN-3.7
Instruction Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
For U.S. models
FCC Information for User
CAUTION:
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Integra/Onkyo dealer.
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners, alco-
hol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
For American Models
•
•
Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV tech-
nician for help.
Pressing the [Standby/On] button to select Standby
mode does not fully shutdown the unit. If you do not
intend to use the unit for an extended period,
remove the power cord from the AC outlet.
5. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Integra/
Onkyo dealer.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you origi-
nally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
Memory backup
The TUN-3.7 uses a battery-less memory backup system
in order to retain radio presets and other settings when it’s
unplugged or in the case of a power failure. Although no
batteries are required, the TUN-3.7 must be plugged into
an AC outlet in order to charge the backup system.
Once it has been charged, the TUN-3.7 will retain the
settings for several weeks, although this depends on the
environment and will be shorter in humid climates.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Thank you for purchasing an Integra
Multi-Platform Tuner. Please read this
manual thoroughly before making connec-
tions and plugging in the unit.
General
❑ Tuner board slot
❑ 12V trigger IN/OUT
❑ IR IN/OUT
❑ RS232 port for interface control
❑ Hi-rigidity, anti-resonant chassis
❑ Aluminum front panel
❑ RI (Remote Interactive) capable
Following the instructions in this manual
will enable you to obtain optimum perfor-
mance and listening enjoyment from your
new Tuner.
Please retain this manual for future refer-
ence.
With C-HDXM Tuner Board Installed
❑ HD Radio reception and XM Satellite Radio
❑ RDS (Radio Data System)
❑ Automatic AM/FM/XM tuning
❑ 40 AM/FM/XM presets
❑ Preset auto scan
❑ Direct tuning
❑ Ground isolation circuit for digital/analog
With C-AMFM Tuner Board Installed
❑ Automatic AM/FM tuning
❑ 40 AM/AM presets
❑ Preset auto scan
❑ Direct tuning
HD Radio™ Technology
Manufactured Under
License From iBiquity
Digital Corporation.
“iBiquity Digital” and the “HD Radio” and “HD”
Symbols are registered trademarks of iBiquity Digital
Corporation. “HD Radio” is a trademark of iBiquity
Digital Corporation. U.S. and Foreign Patents.
The XM name and related logos
are registered trademarks of XM
Satellite Radio Inc.
®
XM Ready , XM Public Radio™ are trademarks of
XM Satellite Radio Inc. ©2006 XM Satellite Radio
Inc. All rights reserved. All other trademarks are the
property of their respective owners.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Supplied Accessories..................................................................................................................6
Before Using the TUN-3.7............................................................................................................6
Installing the Batteries...........................................................................................................7
Front Panel............................................................................................................................8
Rear Panel ..........................................................................................................................10
Remote Controller......................................................................................................................11
Remote Controller ...............................................................................................................11
Optional Tuner Boards ..............................................................................................................12
Connections
Connecting the AM Loop Antenna ......................................................................................14
Connecting the TUN-3.7.............................................................................................................16
Connecting to an Amplifier ..................................................................................................16
About the System Functions ...............................................................................................16
Turning On and Listening to AM and FM Radio......................................................................19
Turning On the TUN-3.7......................................................................................................19
Listening to AM and FM Radio............................................................................................19
Tuning into Stations by Frequency......................................................................................20
Setting the Satellite Radio Mode.........................................................................................22
Selecting XM Satellite Radio...............................................................................................22
Signing Up for XM Satellite Radio.......................................................................................22
Displaying XM Radio Information........................................................................................24
Listening to HD Radio™ Stations.............................................................................................25
Displaying RDS Information ................................................................................................26
Using Presets .............................................................................................................................27
Presetting Your Favorite Stations........................................................................................27
Selecting Presets ................................................................................................................27
Deleting Presets..................................................................................................................27
Changing the Remote ID............................................................................................................28
Others
Troubleshooting.........................................................................................................................29
If you can’t resolve an issue, try resetting the AV receiver by holding down the [Memory] button
and pressing the [Standby/On] button.
Specifications.............................................................................................................................31
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Before Using the TUN-3.7
Make sure you have the following accessories:
Connecting the Supplied Power Cord
Plug the supplied power cord into this AC INLET.
• Do not use a power cord other than the one supplied
with this tuner. It’s designed exclusively for use with
this tuner and should not be used with any other com-
ponent.
• Never disconnect the power cord from the tuner while
the other end is still plugged into a wall outlet. Doing
so may cause an electric shock. Always disconnect
the power cord from the wall outlet first.
Remote controller and two batteries (AA/R6)
DO NOT connect the
power cord at this time.
Audio cable (1)
Power cord
(supplied)
cable (1)
To use
, the TUN-3.7 must be connected with an
cable and an audio cable.
Power cord
(Plug type varies from country to country.)
* In catalogs and on packaging, the letter added to the end of
the product name indicates the color of the TUN-3.7. Speci-
fications and operation are the same regardless of color.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using the TUN-3.7—Continued
Installing the Batteries
Aiming the Remote Controller
When using the remote controller, point it toward the
TUN-3.7’s remote control sensor, as shown below.
Open the battery compartment, as shown.
1
Remote control sensor
TUN-3.7
Insert the two supplied batteries (AA) in
accordance with the polarity diagram
inside the battery compartment.
2
30˚
30˚
Notes:
• The remote controller may not work reliably if the
TUN-3.7 is subjected to bright light, such as direct
sunlight or inverter-type fluorescent lights. Keep this
in mind when installing.
Close the battery compartment.
3
• If another remote controller of the same type is used
in the same room, or the TUN-3.7 is installed close to
equipment that uses infrared rays, the remote control-
ler may not work reliably.
• Don’t put anything, such as a book, on the remote
controller because the buttons may be pressed inad-
vertently, thereby draining the batteries.
• The remote controller may not work reliably if the
TUN-3.7 is installed in a rack behind colored glass
doors. Keep this in mind when installing.
• The remote controller will not work if there’s an
obstacle between it and the TUN-3.7’s remote control
sensor.
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a
long time, remove the batteries to prevent damage
from leakage and corrosion.
• Flat batteries should be removed as soon as possible
to prevent damage from leakage and corrosion.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the TUN-3.7
Front Panel
A
B C 4 5
6 7
8
9 J
K
L M
For detailed information, refer to the pages in parentheses.
* XM Radio/HD Radio reception requires C-HDXM
tuner board.
A Standby/On button (19)
Sets the TUN-3.7 to On or Standby.
B Standby indicator (19)
C Category [ ]/[ ] buttons (23, 26)
HD Radio stations, they’re used to select multicast
channels.
D Preset [ ]/[ ] buttons (27)
Used to select radio presets.
E Dimmer button (9)
Adjusts the display brightness.
F Display button (24, 26)
Used to view various information on the display.
G Band button (19, 22)
Used to select radio bands, AM, FM, and so on. The
bands available depends on the type of tuner board
installed.
H Tuning/CH [ ]/[ ] buttons (19, 23)
With AM and FM, these buttons are used for tuning.
With XM Radio, they’re used to select stations.
I Auto Scan button (26, 27)
Starts the Auto Scan function, which selects and
outputs each radio preset in turn for 5 seconds.
Receives control signals from the remote controller.
K Display
See the next page.
L Memory button (27)
Used to store and delete radio presets.
M Tuning Mode button (19, 23, 27)
With AM and FM, this button selects the Auto or
Manual tuning mode. With XM Radio, it selects the
search modes.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the TUN-3.7—Continued
Display
8
1 2 3 4 5 6 7
9 J K
L
A XM (requires C-HDXM tuner board)
Lights up if the installed tuner board supports XM
Satellite Radio. When XM is selected, a box appears
around it.
I
HD TUNED
The TUNED indicator lights up when prop-
erly tuned to a radio station. During Auto Tuning,
the Tuning Arrows flash. When tuned to an HD
Radio station, the indicator appears as
B FM
HD TUNED
J AUTO
Lights up when Auto Tuning mode is selected.
K MEMORY
.
Lights up if the installed tuner board supports FM.
When FM is selected, a box appears around it.
C AM
Lights up if the installed tuner board supports AM.
When AM is selected, a box appears around it.
Lights up when presetting radio stations.
D HD Radio
L Message area
Lights up if the installed tuner board supports HD
Radio technology. When the HD Radio band is
selected, a box appears around it.
Various information is displayed here, including
radio preset numbers, tuning frequency, and so on.
E RDS (requires C-HDXM tuner board)
Lights up when tuned to an FM radio station that
supports RDS (Radio Data System).
F STEREO
Lights up when radio reception is in stereo.
The indicator does not light up if the installed tuner
board supports HD Radio technology.
Setting the Display Brightness
G MONO
With this function, you can adjust the brightness of the
display.
Lights up when radio reception is in mono.
The indicator does not light up if the installed tuner
board supports HD Radio technology.
Press the [Dimmer] button
repeatedly to select: dim, dim-
mer, or normal brightness.
Alternatively, you can use the [Dim-
H HD Radio indicators
(These indicators function only when a tuner board
that supports HD Radio technology, such as a C-
HDXM, has been installed.)
Remote controller
mer] button on the tuner.
DIGITAL: Lights up when a digital HD Radio
transmission is being received.
ANALOG: Lights up when an analog HD Radio
transmission is being received.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the TUN-3.7—Continued
Rear Panel
■ C-HDXM tuner board installed
5
1 2 3
4
67
8
9
■ C-AMFM tuner board installed
5
2 3
4
67
8
9
For detailed information, refer to the pages in parentheses.
The 12V TRIGGER OUT jack can be connected to
the 12-volt trigger input on another component, so
that when the TUN-3.7 is turned on, the other com-
ponent turns on as well.
A XM ANTENNA (C-HDXM tuner board only)
(21)
This jack is for connecting the XM Mini-Tuner (not
supplied).
G IR IN/OUT (18)
B FM 75Ω ANTENNA (14)
A commercially available IR receiver can be con-
nected to the IR IN jack, allowing you to control the
TUN-3.7 while you’re in another room, or control it
when it’s out of sight, for example, installed in a
cabinet.
A commercially available IR emitter can be con-
nected to the IR OUT jack to pass IR (infrared)
This jack is for connecting an indoor or outdoor FM
antenna. An indoor FM antenna is supplied with
each tuner board.
C AM ANTENNA (14)
These push terminals are for connecting an AM
loop antenna or outdoor AM antenna. An AM loop
antenna is supplied with each tuner board.
D AUDIO OUTPUT (16)
H RS232
Using the supplied audio cable, connect these out-
put jacks to an analog audio input on your amp.
This port is for connecting the TUN-3.7 to home
automation equipment and external controllers.
E
REMOTE CONTROL (17)
I Power cord (6)
These two identical
can be connected to the
(Remote Interactive) jacks
jacks on your other
The power cord should be connected to a suitable
wall outlet.
Integra/Onkyo components for interactive control.
To use , the TUN-3.7 must be connected with an
cable and an audio cable.
F 12V TRIGGER IN/OUT (17)
The 12V TRIGGER IN jack can be connected to the
12-volt trigger output on another component, so that
when the other component is turned on, the
TUN-3.7 turns on as well.
See pages 16–18 for connection information.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
Remote Controller
A Standby/On button (19)
Sets the TUN-3.7 to On or Standby.
B Number buttons (20, 23, 28)
Used to select radio presets by number, and to enter
AM/FM station frequencies and XM Radio channel
numbers in Direct Tuning mode.
1
2
3
9
J
Selects the Direct Tuning mode. With AM and FM,
quency. With XM, you can select a station directly
by entering its channel number.
K
L
D Return button (28)
Returns to the previous display.
4
E Arrow [ ]/[ ]/[ ]/[ ] buttons (12, 22–25, 28)
With AM and FM, the Up and Down [ ]/[ ] but-
tons are used for tuning. With XM Radio, the Up
and Down [ ]/[ ] buttons are used to select chan-
nels.
5
6
M
The Left and Right [ ]/[ ] buttons are used to
select category.
6
7
8
M
N
Used to select radio presets.
G Auto Scan button (26, 27)
Starts the Auto Scan function, which selects and
H Band button (19, 22)
bands available depends on the type of tuner board
installed.
I Display button (24, 26)
Used to view various information on the display.
J Dimmer button (9)
K Ent and Enter buttons (12, 22–25, 28)
used to select secondary multicast channels with
HD Radio stations.
L Setup button (12, 22, 24, 28)
Selects Setup mode.
M Tuning/CH [ ]/[ ] buttons (19, 23)
With AM and FM, these buttons are used for tuning.
With XM Radio, they’re used to select stations.
N Tuning Mode button (19, 23)
With AM and FM, this button selects the Auto or
Manual tuning mode. With XM Radio, it selects the
search modes.
* XM Radio/HD Radio reception requires C-HDXM
tuner board.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Tuner Boards
The following optional tuner boards are available for the TUN-3.7.
Board slot
Product number: C-AMFM
AM/FM tuner
Product number: C-HDXM
HD Radio AM/FM tuner, and XM Satellite Radio tuner
Caution:
• Before installing or removing a board, be sure to turn off the TUN-3.7 and unplug the power cord from the wall out-
let. Failure to do so could seriously damage your equipment.
AM Frequency Step Setup
Use the Up and Down Arrow
]/[ ] buttons to select “AM
Freq.”
With some tuner boards, there will
only be one option available and you
won’t need to use the Up and Down
Arrow [ ]/[ ] buttons.
3
[
Remote controller
In most cases, you do not need to perform the following
procedure. However, if the purchased board is the
worldwide model and you plan to use it in North Amer-
ica, you must change the AM Frequency setting to
10 kHz after installing the board.
Press the [Setup] button.
1
Use the Left and Right Arrow
Remote controller
4
[
]/[ ] buttons to select:
Remote controller
9 kHz: Select if 9 kHz steps are used
in your area.
10 kHz: Select if 10 kHz steps are
used in your area.
Use the Up and Down Arrow
2
[
]/[ ] buttons to select “Hard-
Remote controller
ware Setup,” and then press
[Enter].
With some tuner boards, there will
only be one option available and you
won’t need to use the Up and Down
Arrow [ ]/[ ] buttons.
Press the [Setup] button.
5
Remote controller
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Tuner Boards—Continued
Installing a Tuner Board
Insert the board between the guide rails
and push it in.
4
Use the Allen wrench, hexagonal socket head screws,
removal thumbscrews, and so on supplied with the tuner
board.
Turn off the TUN-3.7, and then unplug the
power cord from the wall outlet.
1
Use the supplied Allen wrench to unscrew
2
the two hexagonal socket head screws
that are securing the existing board or
blanking plate.
When the board meets the internal connector,
apply a little more pressure so that the board
plugs fully into the connector. Make sure the
board’s panel is flush with the TUN-3.7’s rear
panel.
Use the Allen wrench to screw tight the
two hexagonal socket head screws so
that the board is secure.
5
Note:
To remove an existing tuner board, use the fol-
lowing procedure.
Screw the supplied removal thumbscrews
into the two holes just below the holes
that were used by the hexagonal socket
head screws. Screw them in about 3/16"
(5 mm). Hold and pull both of the thumb-
screws to remove the board.
Be sure to fully tighten the screws. If they are
loose, the ground connection between the board
and the TUN-3.7 may be inadequate, resulting in
noise or failure.
Caution:
75
If any of the screws use washers, be sure to reuse
them when installing or removing a board.
Carefully remove the board from its bag.
3
To prevent electrostatic
damage, hold the board by
its panel, taking care not
to touch any of the com-
ponents or the underside
of the circuit board with
your bare hands.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas
This section explains how to connect the indoor FM
antenna and AM loop antenna, and how to connect com-
mercially available outdoor FM and AM antennas.
Connecting the AM Loop Antenna
The indoor AM loop antenna is for indoor use only.
* An indoor FM antenna and AM loop antenna are sup-
plied with each tuner board.
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
1
FM antenna jack
AM antenna push terminals
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
2
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around).
Connecting the Indoor FM Antenna
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
The indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown.
1
Insert the plug fully
into the jack.
Push
Insert wire
Release
Once the TUN-3.7 is ready for use, you’ll need to
tune into an FM radio station and adjust the posi-
tion of the FM antenna to achieve the best possi-
ble reception.
Use thumbtacks or something similar to
fix the FM antenna into position.
Once the TUN-3.7 is ready for use, you’ll need to
tune into an AM radio station and adjust the posi-
tion of the AM antenna to achieve the best possi-
ble reception.
2
Keep the antenna as far away as possible from the
TUN-3.7, TV, speaker cables, and power cords.
If you cannot achieve good reception with the indoor
AM loop antenna, try using it with a commercially
available outdoor AM antenna.
Thumbtacks, etc.
Caution: Be careful that you don’t injure your-
self when using thumbtacks.
If you cannot achieve good reception with the indoor
FM antenna, try using a commercially available outdoor
FM antenna instead.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the indoor
FM antenna, try a commercially available outdoor FM
antenna instead.
If good reception cannot be achieved using the AM loop
antenna, an outdoor AM antenna can be used in addition
to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in
an attic or loft.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situ-
ated well away from power lines and other high-volt-
age equipment.
Outdoor AM antennas work best when installed hori-
zontally outside, but good results can sometimes be
obtained indoors by mounting horizontally above a win-
dow. Note that the AM loop antenna should be left con-
nected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and
TV reception, as this can cause interference problems. If
circumstances demand it, use a TV/FM antenna splitter,
as shown.
TV/FM antenna splitter
To TUN-3.7
To TV (or VCR)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TUN-3.7
RCA Audio Connection Color Coding
Before Making Any Connections
• Refer to the instructions that came with the com-
ponent you are connecting.
• Do not plug in the power cord until all other con-
nections are complete.
• Red plugs are used for the right channel, white
plugs are used for the left channel.
Left (white)
L
• Do not bind audio cables with power cords and
speaker cables. Doing so may adversely affect the
sound quality.
Right (red)
R
• To prevent interference, keep power cords and
speaker cables as far away as possible from the
antennas.
• Push each plug in all the way to make a good con-
nection (loose connections can cause noise or mal-
functions).
Right!
Wrong!
Connecting to an Amplifier
About the System Functions
Use the supplied audio cable to connect the TUN-3.7’s
AUDIO OUTPUT L/R jacks to the TUNER IN jacks on
your amplifier, as shown.
If you connect the TUN-3.7 to another Integra/Onkyo
-capable component with the supplied
and audio cable, you can use the following system func-
tions. cables are special cables solely for use with
cable
To use the
system functions, use the supplied
Integra/Onkyo products.
cable to make an
connection (see the next column).
Auto Power On
When you turn on the TUN-3.7, your Integra/Onkyo
amplifier or receiver will turn on automatically. (The
amplifier’s POWER switch must be set to ON for this to
work.)
Direct Change
When you select a radio preset or change the band (AM,
FM, etc.), your Integra/Onkyo amplifier will automati-
cally select the TUN-3.7 as the input source.
TUN-3.7
Supplied audio
cable
Remote Control Operation
Supplied
cable
You can control the TUN-3.7 by using your Inte-
gra/Onkyo amplifier or receiver’s remote controller. See
the amplifier or receiver’s instruction manual for details.
L
TUNER
Amplifier
Note:
• If the TUN-3.7 is used with another Integra/Onkyo
component, refer to its instruction manual as well.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TUN-3.7—Continued
With
(Remote Interactive), you can control your
Connecting the 12V Trigger Jacks
-capable Integra/Onkyo CD player, TUN-3.7, and
so on with your amp’s remote controller.
To have the TUN-3.7 turn on automatically when
another component is turned on, connect the TUN-3.7’s
12V TRIGGER IN jack to a 12-volt trigger output on
the other component with a miniplug cable.
• To use
, you must make an analog audio con-
nection between your amplifier and each audio
component.
Likewise, to have another component turn on automati-
cally when the TUN-3.7 is turned on, connect the
TUN-3.7’s 12V TRIGGER OUT jack to a 12-volt trig-
ger input on the other component with a miniplug cable.
Integra/Onkyo amplifier, etc.
Amplifier, AV receiver, etc.
MASTER VOLUME
TUNING
/
PRESET
STANDBY/ON
ENTER
jack
jack
Integra/Onkyo
CD player, etc.
STANDBY
12 TRIGGER OUT
V
Z
O
N
E
2
O
F
F
ZONE
2
RETURN
SETUP
TONE
+
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
ZONE
2
LEVEL
VIDEO
4
INPUT
PHONES
PURE AUDIO
MULTl CH
DVD
VIDEO
1
VIDEO
2
VIDEO
3
VIDEO
4
TAPE
TUNER
CD
SETUP MIC
S
VIDEO
VIDEO
L
AUDIO
R
DIGITAL
VCR
1
VCR
2
TUN-3.7
TUN-3.7
CD player, etc.
12
V
TRIGGER
IN
jack
Remote Interactive
Dock, etc.
cable
Notes:
• Push each plug in all the way to make a good connec-
tion.
• Use only dedicated
cables for
connections.
cables are supplied with Integra/Onkyo tuners
and players (DVD, CD, etc.).
• Some components, including the TUN-3.7, have two
jacks. They’re both the same, so use either one.
•
jacks should be connected only to Integra/Onkyo
components. Connecting them to another manufac-
turer’s component may cause a malfunction.
• Some components may not support all
functions.
See the manuals supplied with your other Integra/
Onkyo components for more information.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TUN-3.7—Continued
Controlling Components That Are Out of Range
You can use the following multi-room kits to control the
TUN-3.7 when it’s out of range of the remote controller:
Controlling Other Out-of-range
Components
• Multiroom AV distribution and control systems such
If another component is out of range of its remote con-
troller, you can use a commercially available IR emitter
to retransmit the remote controller signals received at
the TUN-3.7’s IR IN, as shown below.
®
®
as those made by Niles and Xantech .
IR receiver
Connecting
block
IR IN
IR OUT
TUN-3.7
IR emitter
Remote controller
Controlling the TUN-3.7 When It’s Out of
Range
Other
component
If the TUN-3.7 is located in another room, installed in a
cabinet, or out of range of its remote controller, you can
use a commercially available IR receiver to pickup the
remote controller signals and feed them to the TUN-3.7,
as shown below.
: Signal flow
Connect the IR emitter to the TUN-3.7’s IR OUT, and
place the IR emitter in front of the other component’s
remote control sensor (usually located on its front
panel), as shown below. See the instructions supplied
with the IR emitter.
IR receiver
Connecting
block
Other component
Remote control
IR IN
sensor
from connecting block
TUN-3.7
IR emitter
Miniplug cable
Remote controller
Inside
Miniplug
cabinet
: Signal flow
IR Emitter
Connect the IR receiver to the TUN-3.7 as shown
below.
TUN-3.7
:Signal flow
from connecting block
Only remote controller signals received by the
TUN-3.7’s IR IN are fed through to the IR OUT. Signals
picked up by the TUN-3.7’s remote control sensor are
not output.
Miniplug cable
TUN-3.7
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On and Listening to AM and FM Radio
Listening to AM and FM Radio
Standby/ON
Tuning/CH
Press the [Band] button repeat-
edly to select AM or FM.
1
The
or
indicator lights up.
Remote controller
Standby indicator
Standby/On
Tuning Mode
Band
Press the [Tuning Mode] button
repeatedly to select Auto or Man-
ual Tuning mode.
2
•
Auto Tuning Mode
The AUTO indicator appears and
stereo radio reception is possible.
Manual Tuning Mode
The MONO indicator appears and
radio reception will be in mono.
Remote controller
•
Tuning/CH
Tuning Mode
/
Band
AUTO indicator
MONO indicator
Note:
The MONO indicator does not light up
if the installed tuner board supports
HD Radio technology.
Turning On the TUN-3.7
•
Auto Tuning Mode
Connect the power cord to a suit-
able wall outlet.
The AUTO indicator appears.
Manual Tuning Mode
AUTO indicator disappears.
1
2
•
Press the [Standby/On] button
on the TUN-3.7 or remote control-
ler.
The TUN-3.7 turns on, and the
Standby indicator goes off.
Use the Tuning/CH [ ]/[ ] but-
tons to tune into a station.
In Auto Tuning mode, once a station is
found, tuning stops automatically.
The American model changes FM fre-
quency in 0.2 MHz steps, 10 kHz steps
for AM.
For other models, it’s 0.05 MHz steps
for FM and 9 kHz or 10 kHz steps for
AM.
3
Remote controller
To turn off the TUN-3.7, press the
[Standby/On] button. The TUN-3.7
will enter Standby mode.
Remote controller
Note that the TUN-3.7 is not com-
pletely shutdown in Standby mode.
In Manual Tuning mode, the frequency
stops changing when you release the
buttons. Press the buttons repeatedly to
change the frequency one step at a time.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On and Listening to AM and FM Radio—Continued
When tuned into a station, the
TUNED indicator appears.
TUNED
Number buttons
Direct Tuning
Tuning into weak stereo FM stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Tuning into Stations by Frequency
You can tune into AM and FM stations directly by
entering the appropriate frequency.
Press the [Direct Tuning] button.
1
Remote controller
(Actual display depends on country.)
Within 8 seconds, use the num-
2
Remote controller ber buttons to enter the fre-
quency of the radio station.
For example, to tune into an FM sta-
tion at 87.5 MHz, press [8], [7], and
[5].
Adjusting the Antennas
Adjusting and installing the FM antenna
Choose a location for the FM antenna while
listening to an FM station.
Adjusting the AM antenna
Adjust the location and position of the
AM antenna while listening to an AM sta-
tion to achieve the best possible reception.
1
2
Change the direction of the
Affix the antenna with a thumbtack. (Do not
antenna to achieve the best
possible reception.
push the thumbtack through the antenna.)
Caution: Be careful not to prick your finger!
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to XM Satellite Radio
A warning against reverse engineering:
®
Listening to XM Satellite Radio
(North American Models Only)
It is prohibited to copy, decompile, disassemble, reverse
engineer, or manipulate any technology incorporated in
receivers compatible with the XM Satellite Radio sys-
®
tem. Furthermore, the AMBE voice compression soft-
Important XM Radio Information
ware included in this product is protected by intellectual
property rights including patent rights, copyrights, and
trade secrets of Digital Voice Systems, Inc. The user of
this or any other software contained in an XM Radio is
explicitly prohibited from attempting to copy, decom-
pile, reverse engineer, or disassemble the object code, or
in any other way convert the object code into human-
readable form. The software is licensed solely for use
within this product.
XM Satellite Radio offers an extraordinary variety
of commercial-free music, plus the best in sports,
news, talk and entertainment. XM is broadcast in
superior digital audio from coast to coast. From
rock to reggae, from classical to hip hop, XM has
something for every music fan. XM’s dedication to
playing the richest selection of music is matched by
its passion for live sporting events, talk radio, up-to-
the-minute news, stand-up comedy, children’s pro-
gramming, and much more. For U.S. customers,
information about XM Satellite Radio is available
ers, information about XM Canada is online at
Connecting the XM Mini-Tuner and Home
Dock
To receive XM Satellite Radio, you need an XM Mini-
Tuner and Home Dock, which includes a home antenna.
These are sold separately. For connection information,
refer to the instruction manual supplied with the XM
Mini-Tuner and Home Dock.
Note:
Hardware and required monthly subscription sold sepa-
rately. Other fees and taxes, including a one-time activa-
tion fee may apply. Subscription fee is consumer only.
All fees and programming subject to change. Channels
with frequent explicit language are indicated with an
XL. Channel blocking is available for XM radio receiv-
ers by calling 1-800-XMRADIO (US residents) and
1-877-GET-XMSR (Canadian residents).
XM antenna jack
For a full listing of the XM commercial-free channels
and advertising-supported channels, visit lineup.xmra-
dio.com (US residents) or xmradio.ca (Canadian resi-
dents).
Subscriptions subject to Customer Agreement available
at xmradio.com (US residents) and xmradio.ca (Cana-
dian residents). Only available in the 48 contiguous
United States and Canada. ©2006 XM Satellite Radio
Inc. All rights reserved. All other trademarks are the
property of their respective owners
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to XM Satellite Radio—Continued
Selecting XM Satellite Radio
Band
Press the [Band] button repeat-
edly to select XM.
1
If “CHECK ANTENNA” appears on
the display, make sure the XM Mini-
Tuner is connected properly.
Setup
Enter
Remote controller
/
/
/
Band
Signing Up for XM Satellite Radio
Once you have installed the XM Mini-Tuner and Home
Dock, you are ready to subscribe to XM Satellite Radio.
You’ll need a major credit card and your XM Radio ID.
There are three places you can find your 8-character
XM Radio ID:
Setting the Satellite Radio Mode
Press the [Setup] button.
1
1. On the XM Mini-Tuner
2. On the XM Mini-Tuner packaging
3. On XM Channel 0, as explained below
Remote controller
Use the Up and Down Arrow
1
[
]/[ ] buttons to select“RADIO
Remote controller
ID.”
Use the Up and Down Arrow
2
[
]/[ ] buttons to select “SAT
Alternatively, press the [Direct Tuning]
button, followed within 8 seconds by
the [0] button and [Enter] button.
Remote controller
Radio Mode,” and then press
[Enter].
Your XM Satellite Radio ID number is
displayed. Write it below.
ID:
To sign up, go to:
Use the Left and Right Arrow
2
3
Or call: 1-800-XM-RADIO
(1-800-967-2346)
[
]/[ ] buttons to select “XM.”
Remote controller
The choices available depends on the
type of tuner board you’re using.
For XM Canada, go to:
If you’ve not using satellite radio,
select None.
Or call: 1-877-GET-XMSR
(1-877-438-9677)
Press the [Setup] button.
4
Remote controller
Notes:
• RADIO ID cannot be selected in Category Search
mode. You must select Channel Search mode (see
page 23).
• The following letters are not used in XM Satellite
Radio IDs: I, O, S, F.
• XM Satellite Radio will transmit a special signal to
the TUN-3.7 to activate the full channel lineup. Acti-
vation normally takes between 10 and 15 minutes, but
during busy peak periods, you may need to leave the
TUN-3.7 turned on for up to an hour.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to XM Satellite Radio—Continued
Category Search Mode
Tuning/CH
Press the [Tuning Mode] button
to select Category Search mode.
1
Remote controller
Tuning Mode
Category
/
Use the TUN-3.7’s [Category]
2
[
]/[ ] buttons, or remote con-
troller’s Left and Right [ ]/[
buttons to select a category, and
use the TUN-3.7’s Tuning/CH
]
Number buttons
Direct Tuning
Return
[
]/[ ] button, or remote con-
troller’s Up and Down Arrow
]/[ ] buttons to select a chan-
nel in that category.
Enter
[
/
/
/
Tuning/CH
Tuning Mode
/
Remote controller
Selecting XM Radio Channels
There are three ways to select XM Radio channels:
• Channel Search mode: select any channel.
• Category Search mode: select channels by category.
• Direct tuning: enter channel number.
Direct Tuning
You can select an XM Radio channel directly by enter-
ing its number with the remote controller.
Channel Search Mode
Press the [Direct Tuning] button.
1
Remote controller
Press the [Tuning Mode] button
1
to select Channel Search mode.
Remote controller
Within 8 seconds, use the num-
ber buttons to enter the channel
2
Remote controller
number.
For example, to select channel #20,
press [0], [2], and [0], or press [2], [0],
and [Enter].
Use the TUN-3.7’s Tuning/CH
2
[
]/[ ] button, or remote con-
troller’s Up and Down Arrow
]/[ ] buttons to select a chan-
[
nel.
Remote controller You can also use the remote control-
ler’s Left and Right Arrow [ ]/[
buttons to select a category.
]
Selecting the Previous Channel
To listen to the previously selected XM channel, press
the [Return] button.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to XM Satellite Radio—Continued
NO SIGNAL
Display
Display
The signal is too weak. Check the XM Mini-Tuner
and/or antenna connection and reposition it for the best
reception.
LOADING
The TUN-3.7 is tuning or decoding audio or text data.
Please wait.
Setup
Enter
OFF AIR
The XM channel you selected is not currently broad-
casting. Select another channel.
Positioning the XM antenna
You can check the signal strength of the XM Radio sig-
nal and adjust the position of the XM antenna accord-
ingly.
Press the [Setup] button.
1
Displaying XM Radio Information
Remote controller
Press the [Display] button repeatedly to cycle
through the available information.
Channel name
Use the Up and Down Arrow
2
Remote controller [ ]/[ ] buttons to select
“Antenna Aiming,” and then
press [Enter].
Channel number
Channelnumber
& preset number
Preset number
Category
Adjust the position of the XM
3
antenna so that the satellite
(SAT) signal strength bar is as
long as possible.
Artist name
Song title
If you can’t receive the satellite (SAT)
signal, adjust your XM antenna so that
the terrestrial (TER) signal strength bar
is as long as possible.
Note:
If the category, artist, or song title is not available,
“- - -” will be displayed instead.
Press the Down Arrow [ ] button to
display the terrestrial (TER) signal bar.
■ XM Radio Messages
The following messages may appear while using XM
Radio.
Terrestrial signals are only available in
certain areas.
CHECK ANTENNA
The XM Mini-Tuner and/or antenna is not connected
properly. Check the connection.
UPDATING
The XM user encryption code is being updated. Please
wait.
So long as the signal strength is good,
you can enjoy XM Radio by using
either satellite or terrestrial reception.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to HD Radio™ Stations
HD Radio technology brings digital radio to conven-
tional analog AM and FM radio stations, with improved
sound quality, better reception, and new data services.
HD Radio technology provides CD-quality sound for
FM stations, and FM-quality sound for AM stations. In
addition, FM HD Radio stations can transmit multiple
programs on the same frequency by using multicast
channels. Text data display incudes station name, song
title, artist name, and so on.
Category
/
Display
Auto Scan
For more information about HD Radio technology,
visit:
Display
Enter
HD Radio stations broadcast on the same AM and FM
frequencies they’ve always used, and you can receive
them by tuning into your favorite station as normal (see
pages 19, 20). If the current AM or FM station supports
HD Radio technology, the HD Radio indicator lights up.
When an HD Radio transmission is received, a box
appears around the HD Radio indicator, and “HD”
appears in the right corner of the message area.
Auto Scan
Selecting Multicast Channels
FM HD Radio stations can transmit multiple programs
on the same frequency by using what are called multi-
cast channels.
Light up with HD
Radio reception.
HD Radio indicator
■ Using the remote controller:
Use the Up and Down Arrow
Remote controller [ ]/[ ] buttons to select a multi-
cast channel.
1
Station name
Band
HD Radio channel number
If you select a multicast channel that is
not currently broadcasting, a plus [+]
symbol will appear next to the HD
indicator, indicating that the channel
has been reserved. When broadcasting
commences, hat channel will be
selected automatically.
• If the current AM or FM station supports HD Radio
technology, the station’s name will be displayed
instead of the band and frequency.
• When music data is received, song title and artist
name information will be displayed next to the HD
indicator.
• If the current HD Radio station supports multicast
channels, the currently selected multicast channel
will be displayed to the right of the HD indicator.
Reserved channel indication
HD Radio channel number
Note:
Multicast channels are not available on
AM.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using RDS
Listening to HD Radio™ Stations—
Continued
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. RDS is approved
by the National Radio Systems Committee (NRSC) and
is available in North America.
■ Using the TUN-3.7:
Press the [Category] [ ]/[
buttons.
]
1
Many FM stations use it these days. In addition to dis-
playing text information, RDS can also help you find
radio stations by type (e.g., news, sport, rock, etc.).
This product supports the following types of RDS infor-
mation: Program Service Name (PS), Radio Text (RT),
and Program Type (PTY).
Selecting the Audio Format
(Blend Mode)
Displaying RDS Information
HD Radio stations transmit both analog and digital ver-
sions of their programs and you can choose which one
you want to listen to.
The RDS indicator lights up when tuned to an FM radio
station that supports RDS.
RDS indicator
Use the [Auto Scan] button to
select Auto or Analog.
Remote controller
Press the [Display] button repeatedly to cycle through
the available information.
Auto: Select to use the digital signal
when available.
1. Program Service Name
When tuned to an RDS station that’s broadcasting
PS information, the station’s name will be dis-
played.
Anlg (Analog): Select to use the ana-
log signal.
2. Radio Text
Note:
When tuned to an RDS station that’s broadcasting
RT text information, the text will be shown on the
display.
• Multicast channels 2 through 8 only carry a digital
signal, so to select an audio format, you must select
multicast channel #1 first.
3. Program Type
When tuned to an RDS station that’s broadcasting
PTY information, the type of program will be dis-
played.
Displaying HD Radio Information
Press the [Display] button repeatedly to cycle through
the available information.
Note:
HD Radio
channel number
If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
Frequency
Frequency &
HD Radio
channel number
Scrolling
station information
Station
information
Artist name
Song title
Artist
information
Song title
information
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Presets
Selecting Presets
■ Using the Preset buttons:
To select a preset, use the
TUN-3.7’s Preset [ ]/[ ] buttons,
or the remote controller’s Preset
[+]/[–] buttons.
Auto Scan
Memory
Tuning Mode
Preset
/
Remote controller
Preset –/+
Auto Scan
■ Using the Auto Scan function:
Press the [Auto Scan] button.
The Auto Scan function automatically
selects and outputs each radio preset in
turn for 5 seconds.
Remote controller
When you hear the station that you
want to listen to, press the [Auto Scan]
button again to stop auto scanning.
PresettingYour Favorite Stations
You can store any combination of up to 40 of your
favorite AM, FM, and XM Satellite radio stations as
presets.
■ Using the TUN-3.7:
Deleting Presets
Tune into the station that you
want to store as a preset.
1
■ Using the TUN-3.7:
Select the preset that you want to
delete.
See the previous section.
Press the [Memory] button.
The MEMORY indicator appears and
the preset number flashes.
1
2
2
While holding down the [Mem-
ory] button, press the [Tuning
Mode] button.
The preset is deleted and its number
disappears from the display.
While the MEMORY indicator is
displayed (about 8 seconds), use
the Preset [ ]/[ ] buttons to
3
select a preset from 1 through 40.
Press the [Memory] button again
4
to store the station or channel.
The station or channel is stored and the
preset number stops flashing.
Repeat this procedure for all of your
favorite radio stations.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Remote ID
If the TUN-3.7’s remote controller interferes with other
Integra/Onkyo components located in the same room,
you can change the remote control ID. You can select
remote control ID #1, #2, or #3. By default, the remote
control ID is set to #1. If you change the ID, you must
also change the ID on the remote controller to match, as
explained below, otherwise, the remote controller won’t
work.
Use the Left and Right Arrow
]/[ ] buttons to change the
remote ID.
You can select ID #1 (default), #2, or
#3.
4
[
Remote controller
Press the [Setup] button.
5
Once you’ve changed the TUN-3.7’s
remote ID, the remote controller will
no longer control the TUN-3.7, so you
must change the remote controller’s ID
to match, as explained below.
Remote controller
Number buttons
Return
Setup
Enter
/
/
/
Changing the Remote Controller’s ID
Before changing the remote con-
troller’s ID, change the TUN-3.7’s
ID first (see above).
1
Press the remote controller’s
[Return] button.
Changing the TUN-3.7’s Remote ID
2
Remote controller
Press the [Setup] button.
1
Remote controller
While pressing and holding
down the remote controller’s
3
Remote controller
[Return] button, press number
button [1], [2], or [3] for 3 sec-
onds to select ID #1, #2, or #3
respectively.
Use the Up and Down Arrow
2
[
]/[ ] buttons to select “Hard-
Remote controller
ware Setup,” and then press
[Enter].
With some tuner boards, there will
only be one option available and you
won’t need to use the Up and Down
Arrow [ ]/[ ] buttons.
Check whether the remote con-
troller operates the TUN-3.7
properly.
4
Use the Up and Down Arrow
3
Note:
[
]/[ ] buttons to select
Remote controller
• The remote controller and TUN-3.7 must be set to the
same remote control ID. Otherwise, you won’t be
able to control the TUN-3.7 with the remote control-
ler.
“Remote ID.”
With some tuner boards, there will
only be one option available and you
won’t need to use the Up and Down
Arrow [ ]/[ ] buttons.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have any trouble using the TUN-3.7, look for a solution in this section.
If you can’t resolve the issue yourself, try resetting the TUN-3.7 before contacting your Integra/Onkyo dealer.
To reset the TUN-3.7 to its factory defaults, turn it on and, while holding down the
[Memory] button, press the [Standby/On] button. “Clear” will appear on the dis-
play and the TUN-3.7 will enter Standby mode.
Note that resetting the TUN-3.7 will delete your radio presets and custom settings.
Power
Can’t turn on the TUN-3.7.
• Make sure that the power cord is properly plugged into the wall outlet (see page 19). And also, make sure that the
other end of the power cord is properly connected to the TUN-3.7’s AC INLET (see page 6).
• Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.
Audio
There’s no sound.
• Make sure your amplifier’s volume control is not set to minimum.
• Check all connections and correct as necessary (see pages 14 to 18).
Tuner
Reception is noisy, stereo FM reception suffers from hiss, or the STEREO indicator doesn’t light up when tuned
to a stereo FM station.
• Check the antenna connections (see page 14).
• Change the position of the antenna (see page 20).
• Move the TUN-3.7 away from a nearby TV or computer.
• Cars or airplanes can cause noisy interference.
• The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.
• Try selecting Manual Tuning mode (see page 19).
• When listening to an AM station, noise may be heard when you operate the remote controller.
• If none of the above improves the reception, install an outdoor antenna (see page 15).
If a power outage occurs or the power cable is disconnected:
• If the preset stations are lost, preset them again (see page 27).
Can’t adjust the frequency of the radio.
RDS doesn’t work.
• Your Tuner board doesn’t support HD Radio reception.
• The FM station you are tuned to doesn’t support RDS.
• Install an outdoor FM antenna (see page 15).
• Change the position or direction of your outdoor FM antenna (see page 15).
• Move the FM antenna as far away as possible from fluorescent lights (see page 15).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
Remote Controller
The remote controller doesn’t work properly.
• Make sure the batteries have been installed with the correct polarity (+/–) (see page 7).
• Replace both batteries with new ones. (Do not mix different types of batteries or new and old batteries.)
• The remote controller is too far away from the TUN-3.7, or there’s an obstacle between them (see page 7).
• The TUN-3.7’s remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight).
• The TUN-3.7 is located behind the glass doors of a audio rack or cabinet.
• The TUN-3.7 and remote controller may be set to different remote control IDs. Set the TUN-3.7’s remote control ID
first, and then set the remote controller to the same ID (see page 28).
Others
Interactive control with other Integra/Onkyo
-capable components is not working.
• Make sure the
won’t work.
cables and analog audio cables are connected correctly (see page 16). Connecting only an
cable
The TUN-3.7 contains a microcomputer for signal processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity may cause it to lock up. In the unlikely event that this
should happen, unplug the power cord, wait at least 5 seconds, and then plug it again.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
Power Supply:
AC 120 V, 60 Hz
Power Consumption:
Stand-by Power Consumption:
Dimensions (W × H × D):
Weight:
27 W (when C-HDXM board is used)
0.2 W
435 × 81 × 306 mm (17-1/8" × 3-3/16" × 12-1/16") (not include a board)
4.5 kg (9.9 lbs.) (not include a board)
FM
Tuning frequency range:
Usable sensitivity:
Signal-to-noise ratio:
87.5–107.9 MHz
Stereo: 22.2 dBf (IHF)
Stereo: 67 dB (IHF-A)
Mono: 15.2 dBf (IHF)
Mono: 73 dB (IHF-A)
Mono: 0.3% (1 kHz)
THD (total harmonic distortion): Stereo: 0.5% (1 kHz)
Stereo separation:
40 dB (1 kHz)
AM
Tuning frequency range:
Usable sensitivity:
Signal-to-noise ratio:
530–1710 kHz
300 µV
40 dB
THD (total harmonic distortion): 0.7%
Specifications and features are subject to change without notice.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Integra Division of
ONKYO U.S.A. CORPORATION
18 park Way, Upper Saddle River, N.J. 07458, U.S.A.
En
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
I0803-2
SN 29344350A
(C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 4 3 5 0 A *
Download from Www.Somanuals.com. All Manuals Search And Download.
|