Initio Network Card I O HIGHWAY User Manual
®
initio  
TM  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
iii  
Contents  
Technical Support  
ii  
1. INTRODUCTION  
1
The Initio I/OHIGHWAY PCI-FastSCSI host adapter  
Technical Illustration  
Product Features / Specifications  
1
2
3
2. GETTING STARTED  
5
Host adapter and the SCSI bus  
5
SCSI bus preparation  
SCSI bus termination  
5
5
3. HARDWARE INSTALLATION  
7
Installation basics  
7
Installation in ten easy steps  
Hard disk drive preparation  
7
11  
Low-level format  
11  
4. HOST ADAPTER SETUP  
13  
Running the SmartSCSI Setup Utility 13  
Main Menu Options 13  
5 MS-DOS/WINDOWS 3.1X DRIVER INSTALLATION  
Overview 17  
17  
Installing the Initio ASPI driver to an existing MS-DOS system  
Installing the Initio ASPI driver to an existing Win3.1x system  
17  
18  
ASPI Manager command line options  
ASPI CD-ROM Driver Command Line options  
ASPI Disk Driver Command Line options 21  
ASPI Partition and Format Utility 22  
19  
19  
6. MICROSOFT WINDOWS 95/95B (OSR2) DRIVER INSTALLATION 23  
Overview  
Installation  
23  
23  
New Windows 95/95a installation  
Adding the Initio Driver to an existing Windows 95/95a system  
23  
25  
Updating the Initio 95/95a device driver  
New Windows 95b (OSR2) installation  
26  
27  
Adding the Initio driver to an existing Windows 95B (ORS2) System  
Updating the Initio 95B (OSR2) device driver 29  
28  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
iv  
Contents  
7. MICROSOFT WINDOWS NT DRIVER INSTALLATION  
31  
Overview  
Installation  
31  
31  
New Windows NT installation  
31  
Adding or updating the Initio driver to an existing WinNT system  
Installing a new WinNT system and Initio driver w/out floppy disks  
33  
34  
8. NOVELL NETWARE DRIVER INSTALLATION  
35  
Overview  
Installation  
35  
35  
New NetWare 4.xx installation  
Adding the Initio driver to an existing NetWare system  
Device driver command line options 37  
35  
36  
9. IBM OS/2 DRIVER INSTALLATION 39  
Overview  
Installation  
39  
39  
New OS/2 installation  
39  
Adding the Initio driver to an existing OS/2 system 40  
Device driver command line options  
40  
10. SCO UNIX DRIVER INSTALLATION  
43  
Overview  
Installation  
43  
43  
Updating interrupts and hardware settings 43  
Installing the Initio driver in a new SCO UNIX system  
Adding the Initio driver to an existing SCO UNIX system  
Changing to the INI-9XXX as the bootable host adapter  
44  
44  
45  
11. SCO UNIXWARE DRIVER INSTALLATION  
47  
Overview  
Installation  
47  
47  
Updating interrupts and hardware settings 47  
Installing the Initio driver in a new UnixWare system  
Adding the Initio driver to an existing UnixWare system  
47  
48  
Using Multiple Host Adapters  
49  
Removing the Initio driver from a UnixWare system  
49  
TROUBLESHOOTING 51  
INDEX 55  
PRODUCT WARRANTY  
57  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
Introduction  
™
The Initio I/OHIGHWAY is a high-performance  
PCI bus master FastSCSI host adapter which  
provides the interface between the FastSCSI  
bus and the PCI local bus. Distiguishing  
features include:  
1
• Support of 32-bit data transfers across the PCI bus  
The Initio  
I/OHIGHWAY  
Host Adapter  
at speeds up to 133 MBytes per second  
™
• The SmartSCSI Setup Utility program enables  
integration of the host adapters into most platforms  
and operating systems  
• Compliancy with Plug-n-Play applications on  
systems using the PCI bus standard  
I/OHIGHWAY host adapter supports synchronous  
FastSCSI bus transfers at a rate of 10 MBytes  
per second. I/OHIGHWAY utilizes full support of  
FastSCSI standards defined by SCSI  
specifications.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
Technical Illustration  
This illustration identifies major components pertaining to your I/OHIGHWAY host  
adapter. You will find it helpful to refer to this illustration while installing the host  
adapter and attaching the cables.  
FIGURE 1 – INI-9100A Board Layout  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Product Features/Specifications  
Product Features  
• PCI Compatibility: The PCI Bus is a 32-bit bus with multiplexed address and data  
lines. I/OHIGHWAY is compliant with PCI 2.1 bus protocol, electrical and mechanical  
specifications.  
• Plug and Play: I/OHIGHWAY has an on-board read only memory (ROM) to provide the  
necessary configuration mechanisms for installation, configuration, and booting  
without user intervention.  
• 133 MBytes per second PCI burst mode: The 32-bit data path for the PCI bus  
structure running in a synchronous mode at 33 MHz gives maximum operating speeds  
of 133 MBytes/second.  
• 10 MBytes per second data transfer: Up to 10 MBytes/sec synchronous FastSCSI  
data transfers for I/OHIGHWAY.  
• Programmable/Automatic SCSI Termination: Allows the user to choose between  
programmable or auto-SCSI termination, eliminating the need to remove system unit  
covers each time a change is made in SCSI bus configuration.  
• Onboard BIOS supports MS-DOS, Windows 3.1x: I/OHIGHWAY has the necessary  
software support on-board–allowing you to run disk drive operations for MS-DOS and  
Windows 3.1x without any extra drivers.  
• Windows 95, Windows NT, OS/2, SCO UNIX, UnixWare, Linux and NetWare  
Driver Support: I/OHIGHWAY is compatible with all major operating systems.  
• ISGE™ Integrated Scatter/Gather Engine: Initio host adapters have incorporated  
advanced hardware functions to provide increased performance in all Scatter/Gather  
operations.  
• No Hardware Jumpers to set: Initio host adapters embed an intelligent software  
utility to set configuration options.  
• Compatible with Hard Disk, CD-ROM, Optical, Tape, Printer, and other SCSI  
products: I/OHIGHWAY is a complete FastSCSI implementation. All peripherals are  
compliant with SCSI-2 and SCSI-1 and can be used with I/OHIGHWAY.  
• 64-byte FIFO: A 64-byte FIFO buffer is designed into I/OHIGHWAY and is utilized as a  
caching buffer to manage PCI to SCSI bus structure timing for data and command  
transfer.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Product Features/Specifications  
• Command Queuing: A unique implementation to provide 255 simultaneous SCSI  
commands.  
• SCSI compliant: I/OHIGHWAY is fully SCSI compliant, implementing advanced features  
such as:  
• Tag Queuing  
• Sync/Async Transfers  
• Disconnect / Reselect Arbitration  
Product Specifications  
Power Requirements  
• 5.0 ± 0.25 V at 0.51 Amps maximum not including bus termination  
Physical Dimensions  
• 5.75” x 3.40” (14.61 cm x 8.65 cm)  
Environmental Specifications  
Operating Temperature  
• 0 to 55°C (32 to 131°F)  
• 10% to 90% relative humidity (non-condensing)  
Storage Temperature  
• -40 to 75°C (-40 to 167°F)  
• 5% to 95% relative humidity (non-condensing)  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Getting Started  
Host Adapter and the SCSI Bus  
I/OHIGHWAY is a bus mastering host adapter which works with the host computer to  
provide control for the SCSI bus. By daisy chaining peripheral devices together, up to  
seven devices can be linked with I/OHIGHWAY. The host adapter can be placed in any  
standard PCI slot on the bus.  
2
SCSI bus preparation  
Each peripheral device attached to the SCSI bus can either be an internal or external  
device. Each peripheral has a specific device ID, commonly referred to as a SCSI ID.  
Please refer to your peripheral documentation to determine switch or jumper settings for  
SCSI ID’s. No two devices can have the same ID; the device ID uniquely defines the  
device to the SCSI bus.  
SCSI bus termination  
The SCSI bus structure has a length limitation as well as a requirement for termination at  
each end of the SCSI cable. The cable is designed to connect in a daisy chain fashion.  
No branching is permitted in the SCSI bus. The first and last physical SCSI device on  
the SCSI bus must be terminated (FIGURE 2).  
FIGURE 2 – Examples of SCSI bus termination  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Getting Started  
I/OHIGHWAY’s SCSI termination can be set to auto-termination or programmable mode  
via the SmartSCSI Setup Utility. This feature allows the operator to switch the auto-  
termination On or Off. If auto-termination is switched off, the operator can manually  
program termination for the host adapter. There are three ways to manually control  
terminating the host adapter on the SCSI bus (see TABLE 1).  
SCSI Devices Configuration  
Internal Devices Only 1  
SCSI Channel Termination  
ON  
ON  
External Devices Only 1  
Internal & External Devices2  
OFF  
TABLE 1 - I/OHIGHWAY possible termination settings  
1 Assumption: Host adapter is at the end of the SCSI bus  
2 Assumption: Host adapter is in the middle of the SCSI bus  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Hardware Installation  
Installation Basics  
The internal cable permits connection of multiple internal devices. SCSI devices that are  
connected to the internal connector are installed inside the host computer enclosure.  
The external connector is accesible through the D-shell connector at the back of the  
host system and is designed to connect devices outside the host system enclosure.  
3
The following table has connector details of I/OHIGHWAY.  
Internal  
Connector  
External  
Connector  
Maximum SCSI  
Devices allowed  
Product  
I/OHIGHWAY  
One 50-pin S/D  
One 50-pin H/D  
7
(INI-9100A)  
S/D: Standard Density...........  
H/D: High Density.................  
TABLE 2 - Connector Details  
To increase the reliability of the cabling being used with the host adapter, it is recom-  
mended that the following guidelines be observed:  
• SCSI-1 – up to 6 meters or 20 feet  
• FastSCSI – up to 6 meters or 20 feet  
• Impedance of the cable should be between 90-110 ohms  
• Use high quality shielded connectors  
Installation inTen Easy Steps  
1 Power down the host computer and all peripherals.  
Remove the cover from the host system. You may need to refer to the system manual  
for cover removal. If necessary, identify the PCI sockets inside the host system with  
the aid of the system documentation.  
2 Use static electricity discharge precautions.  
Remove possible static discharge potential from any objects that the host adapter  
may come in contact with before installation. This can be accomplished by touching  
a bare metal chassis rail after you have turned off the power.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Hardware Installation  
3 Inserting the host adapter  
Orient the host adapter for installation so that the external connector is facing the  
back of the system unit and align the card with the PCI connector on the system unit  
(see FIGURE 3).  
Holding the adapter by the mounting bracket and the card edge, match up the card  
edge connector with the PCI host computer socket and insert the card into the  
socket. Once the connector is in the PCI expansion slot socket tighten the mounting  
bracket screw to secure the card in place.  
FIGURE 3 – Inserting the host adapter into a PCI slot  
4a Installation of internal SCSI cables  
The number of internal and external connectors for Initio’s SCSI host adapters are  
referenced in the hardware installation section (TABLE 2).  
All internal connectors may be used simultaneously or singularly, depending on  
your bus configuration. Installation of internal SCSI cables must be performed  
before replacing the system covers. The internal ribbon cable is made with multiple  
connectors attached and used to daisy chain the host adapter with two or more  
devices. It is important that the cable be installed correctly for proper operation.  
The cable has a colored stripe running the length of the cable, on the edge distin-  
guishing the pin one side of the connector. These identifying markings must match  
when mated on the host adapter board.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Hardware Installation  
When attaching FastSCSI devices, use the 50-pin FastSCSI cable connector on the  
host adapter. Align the internal cable into the host adapter and the other cable  
connectors in a similar fashion into the other SCSI device connectors as described  
in the appropriate manufacturers instructions.  
FIGURE 4 – Connecting the 50-pin internal flat ribbon cable  
4b Installation of external SCSI cables  
Installation of external SCSI cables can be performed after the cover has been  
closed. The cable is limited in length to a total of six meters including any internal  
cabling. The external cable can be daisy chained to include up to seven with the  
host adapter in combination with internal devices. The external cable is designed  
to be inserted only one way, requiring termination at the end peripheral device on  
the bus (FIGURE 5).  
FIGURE 5 – External cable connection  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Hardware Installation  
5 Drive activity LED  
A drive activity LED is designed into the host adapter to indicate when a data  
transfer is being made. Connection to the LED is optional and cabling is not in-  
cluded with this kit. Each host adapter has one four-pin connector. Please refer to  
the host adapter’s illustration (FIGURE 1) for the LED connector that will accomodate  
the LED cable.  
6 Multiple Initiators  
Under some circumstances multiple initiators can be used on a single SCSI bus. The  
bus is configured to have more than one host adapter inserted into at least two  
distinctly different computer systems sharing peripheral devices. In these circum-  
stances, it is possible to have one of the two computer systems turned off. Under  
these conditions, the host adapter has a jumper that can be enabled (closed) to set  
the active on-board termination on all the time, regardless of whether power is  
applied or not. The host adapter is shipped without the jumper installed and need  
not be changed in most cases.  
7 Close the cover on the host computer  
Visually inspect the configuration you have installed to verify that all cables have  
been inserted correctly. Close the cover on the host computer. The hardware  
installation for the host adapter is now complete.  
8 Host computer configuration  
Most computer manufacturers with a PCI bus automatically configure the add on-  
card or host adapter I/O Port address, IRQ Channel and BIOS address. If this is not  
the case with your computer system, you will need to manually configure your  
system.  
There are two means of configuring the PCI bus from the host computer system:  
1. Setting jumpers on the host system motherboard.  
2. Setting CMOS BIOS incorporated into the host system.  
You will need to refer to the host computer system documentation to complete PCI  
bus activation and setup.  
If the host system will be using a SCSI device to provide system boot capability, then  
the system CMOS drive type settings may need to be changed. Under some condi-  
tions the system will expect the boot disk to be an IDE drive. This must be changed  
in order to boot from a SCSI device.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Hardware Installation  
9 System startup  
The newly installed SCSI bus is now ready to power up. Switch on peripheral and  
host computer system power. The system monitor should display the following  
information, but may vary, based on the system BIOS manufacturer.  
• The normal Power-On Self Test and memory test procedure.  
• The host adapter sign on message including a list of attached SCSI devices.  
The list should match the peripheral devices attached to the bus. In most cases the  
host computer system is now configured and ready for use.  
Some situations will require that a low-level format be performed using the host adapter  
SmartSCSI Setup Utility to initialize a SCSI disk drive and lay the foundation for a bootable  
SCSI drive.  
10 SmartSCSI Setup Utility  
The SmartSCSI Setup Utility simplifies the SCSI installation process by eliminating  
the need for opening the system to change system jumpers and switch settings. All  
necessary host adapter functions are accessible through the utility, simplifying  
customization for your system needs. Initio’s SmartSCSI Setup Utility is divided into  
five segments identified by: Scan Bus; Device Setup; Adapter Setup; BIOS Setup; and Disk  
Utility. These program functions are accessible by typing <CTRL><I> at the boot-  
up prompt.  
Hard Disk Drive Preparation  
A new SCSI disk drive is normally low-level formatted at the factory to simplify installa-  
tion. The drive can be used as it comes from the factory once it is partitioned for  
system operation.  
Low-level Format  
A low-level format will erase any data that is stored on the target disk. Before attempting  
to perform a low-level format be sure the data on the target disk has been backed up. A  
low-level format can be achieved via the SmartSCSI Setup Utility for I/OHIGHWAY.  
The low level format sets the media to a state which is easily recognized by the host  
adapter on the SCSI bus. Once this format is completed, you will need to partition the  
drive. Refer to your operating system documentation for further information on parti-  
tioning drives.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Host Adapter Setup  
Running the SmartSCSI Setup Utility  
To start the SmartSCSI Setup Utility, verify that all devices attached to the SCSI bus are  
powered up when the host computer system is turned on. Once the power switch has  
been turned on and the system begins its on screen power up sequence, the Initio banner  
will be displayed for a brief period. During this time the Initio SmartSCSI Setup Utility is  
accessible by pressing the <Ctrl> key and the <I> key at the same time. When displayed  
on your system monitor, the following message indicates that the host system is ready to  
accept your keyboard input.  
4
!!! Press <Ctrl> <I> for SmartSCSI Setup Utility !!!  
Main Menu Options  
SmartSCSI’s main menu provides five possible setup options for meeting your system  
configuration:  
Scan Bus  
Device Setup  
Adapter Setup  
BIOS Setup  
Disk Utility  
Scan Bus  
This option scans the SCSI bus. All device ID’s are displayed on the screen including  
SCSI ID’s without devices attached. This allows for a better definition of location and  
priority on the SCSI bus.  
• A device ID should only be changed if it conflicts with another device address on the same bus. Refer  
to your peripheral documentation for changing SCSI ID’s.  
• The best ID for a bootable hard disk is SCSI ID-Ø.  
Device Setup  
Asynchronous Transfer. Use this option to set the synchronous data transfer mode.  
I/OHIGHWAY will transfer data at a maximum rate of 10 MBytes per second in synchro-  
nous mode and a maximum rate of 5 Mbytes per second in asynchronous mode. Use  
this option to set the synchronous data transfer mode. The default setting for this  
option is for synchronous operation. (no)  
Maximum Synchronous Transfer Rate. This option determines the speed at which  
data is moved across the SCSI cable. I/OHIGHWAY has the option of running up to 10  
MBytes per second.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Host Adapter Setup  
DOS Space > 1 GB. Using this option allows for single disk capacities to be extended  
up to 8 GBytes (yes). Please refer to the Appendix titled DOS Space > 1 GB for further  
information on this feature.  
• (NO) DOS limits the number of cylinders per drive to 1024. The host adapter defines  
head and sector usage to 64 heads and 32 sectors. This format allows for maximum  
capacity of 1 gigabyte per disk storage.  
• (YES) The upper limit can be extended from 1 GByte to 8 GBytes by increasing the  
number of heads to 255 and sectors used per track to 63. This is a powerful option.  
DATA CAN BE LOST BY CHANGING SETTINGS.  
Spin Up Disk Drive. This option is used to initiate motor spin-up for SCSI disk drives.  
The host adapter BIOS can limit system power requirements during power-up. This is  
accomplished by signaling the device to start at delayed intervals (default setting will be  
‘no’).  
Enable Disconnect. The host adapter uses this option to allow a device to temporarily  
disconnect from the SCSI bus (referred to as disconnect/reconnect). This allows the  
host adapter to perform other functions on the bus while the device is temporarily  
disconnected. The device and the host adapter can then reconnect when the bus is  
needed (default setting will be ‘yes’).  
Adapter Setup  
Host Adapter SCSI Bus ID. Used to change the adapter’s SCSI ID on the SCSI bus.  
The narrow host adapters provides eight ID’s available numbered 0-7, with 7 having the  
highest priority (and ID-7 reserved for the host adapter).  
Installation of additional host adapters is permitted on the same PCI bus. This will allow  
the system to have more than one SCSI bus attached. Under these conditions, SCSI  
ID’s can be repeated.  
Boot Device ID. This option selects which SCSI device will be the designated boot  
device for the system. The default ID for this option is 0.  
SCSI Terminators. This option is used to set auto-termination located on the host  
adapter card. This option is also used to manually control termination on the host  
adapter. The normal setting for this option is auto.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
Host Adapter Setup  
SCSI Parity Check ON. Select this option to enable or disable parity checking on the  
SCSI bus by the host adapter. The default setting for this option is on (yes).  
NOTE: If this option is set ON, be certain that the peripheral SCSI device also has this option turned  
ON.  
BIOS Setup  
Enable Host Adapter BIOS. This option controls the host adapter usage of SCSI disk  
I/O routines inside the host adapter BIOS. By disabling this option you will eliminate the  
host adapter’s ability to utilize boot capabilities in I/OHIGHWAY. Setting this to “no” will  
also disable all subsequent features displayed by this on-screen panel. The default  
setting will be on. (Yes)  
BIO SUPPORT for More than Two Drives. This option supports two or more disk  
drives on the SCSI bus for MS-DOS 5.0 or later when enabled. The optimum device  
identification (ID) for multiple drive operation is device ID-0 for a system disk and device  
ID-1 for the second drive. The default setting will be on. (Yes)  
BIOS Treat Removable Disks as Fixed Disk. This option is able to treat removable  
disks as fixed disks. With this option selected you can run removable disk media without  
additional software drivers. The default setting will be off. (No)  
BIOS Support for Bootable CD-ROM. This option allows users to boot from a CD-  
ROM by replying with Yes at the prompt. Only one bootable CD-ROM will be allowed at a  
time. The default setting will be off. (No)  
Disk Utilities  
Format Disk. Use this option to perform a low level disk format on the target device.  
The format will erase all data resident on the targeted disk drive. Refer to the section  
titled “Hard Drive Preparation” for additional information.  
Verify Disk. This option will verify the media of a successfully formatted device and  
verify that the drive is functioning properly. Verify will also identify and flag any bad  
sectors on the disk so that during operation these flagged sectors will not be used. If a  
bad sector is found you are given two options shown below:  
• Reassign will assign the flagged location to another sector on the disk.  
• Skip will not reassign the flagged location.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
MS-DOS/Windows 3.1x Driver Installation  
Overview  
The Initio ASPI driver will support extended SCSI command functions for MS-DOS 3.30  
or later. The on-board BIOS initialized during the power up boot routine only supports  
MS-DOS hard disk operation. If peripherals other than disks are used, such as CD-ROM  
or MO, the Initio ASPI driver will need to be installed in addition to Initio CD-ROM and  
MO drivers.  
5
Installation  
The installation procedure guides you through the installation of the Initio DOS ASPI  
and the ASPI for Windows 3.1x drivers. The installation procedure described here  
requires some experience in MS-DOS or Windows 3.1x system setup and administration.  
The device driver is transferred from the INI-9XXXU/9XXXUW DRIVER DISK 1 to the hard  
drive where it is automatically initialized during the system boot routine.  
The INI-9XXXU/9XXXUW DRIVER DISK 1 contains two installation programs that perform  
the same task. If you have completed installing the Initio ASPI driver using the MS-DOS  
based installation routine described in this User’s Manual, it is not necessary to repeat  
the procedure for a Windows 3.1x environment on the same system.  
Installing the ASPI drivers to an existing MS-DOS system  
The ASPI driver is found on the INI-9XXXU/9XXXUW DRIVER DISK 1. It is important that  
the SCSI bus hardware, and operating system are installed correctly before proceeding  
further. If you need help installing the MS-DOS operating system, please refer to the  
MS-DOS manual before proceeding.  
1 Turn on host system and boot into MS-DOS.  
2 Insert the INI-9XXXU/9XXXUW DRIVER DISK 1 into your floppy drive.  
3 At the MS-DOS prompt, change to your active floppy drive (e.g., type A: <ENTER>).  
4 Type DOSSETUP <ENTER> (A series of screens will guide you through the installation of  
the ASPI device drivers).  
5 The first screen sets the installation drive and directory that the ASPI driver will be  
installed on. Follow the on-screen directions and/or options to continue the installa-  
tion.  
6 To activate the device driver, reboot the system by selecting the Reboot Now option  
at the end of the installation process.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
MS-DOS/Windows 3.1x Driver Installation  
Installing the Initio ASPI drivers to an existing Windows  
3.1x system  
The ASPI for Windows 3.1x drivers are found on the INI-9XXXU/9XXXUW DVR DSK 1. It is  
important that the SCSI bus hardware, and operating system are installed correctly  
before proceeding further. If you need help installing Windows 3.1x, please refer to the  
Microsoft Windows manual before proceeding.  
1 Turn on host system and boot into MS-DOS and Windows 3.1x operating system.  
2 Insert the INI-9XXXU/9XXXUW DRIVER DISK 1 into your floppy drive.  
3 Use your installed mouse or the appropriate key strokes to select RUNꢀ from the  
Windows PROGRAM MANAGER. Execute the following steps:  
• Type A:\SETUP <ENTER>. A series of screens will guide you through the  
installation of the ASPI for Windows device drivers.  
• Choose CONTINUE to continue the installation sequence.  
• Choose CONTINUE to accept the Host Adapter selection.  
4 Two installation options are available:  
• Choose EXPRESS INSTALL to install both the DOS ASPI drivers and the Windows  
32-bit Disk Access drivers. Use this option if you are unfamiliar with configuring a  
DOS or Windows manually.  
• Choose CUSTOM INSTALL to select DOS ASPI drivers or the Windows 32-bit Disk  
Access drivers manually. Use this option only if you are familiar with configuring a  
DOS or Windows PC manually  
5 Follow the on-screen directions and/or options to continue the installation.  
• Choose CONTINUE to accept the default directory or enter the full directory where  
you want ASPI drivers installed.  
• Choose CONTINUE after all the files have been copied and installed to your  
system.  
• Select YES to make the required changes to your system’s CONFIG.SYS and  
SYSTEM.INI configuration files.  
• Once the SETUP COMPLETE screen is displayed, choose CONTINUE.  
6 Last minute changes to this User’s Manual will be displayed in the README.TXT file  
that is shown. To exit the README.TXT file, use your installed mouse or the appropri-  
ate key strokes to select FILE, then EXIT from the Note Pad FILE MENU.  
7 To complete the installation and activate the device driver, exit from your Windows  
3.1x session and reboot the system by pressing <CTRL> + <ALT> + <DEL>.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
MS-DOS/Windows 3.1x Driver Installation  
ASPI Manager Command Line Options  
Below is a list of command line options. The Initio ASPI Manager, ASPI910U, supports  
command line switches to optimize driver operation. From inside the CONFIG.SYS file  
for MS-DOS, use the following format when modifying the device driver switches:  
The standard format for command line switches is:  
Device = C:\INIASPI\ASPI910U.SYS [Driver Config Option]  
/D  
Verbose Mode provides detailed information about the driver on system com-  
mand line when the driver is initialized.  
/L  
Driver scan eight LUNs for each SCSITarget.  
/Bb,dd  
Scan device only on PCI BUS #b, PCI DEVICE #dd  
The range for “b” is from 0 to 7.  
The range for “dd” is from 0 to 20.  
/Bb  
Scan all the devices on the PCI BUS #b  
The range for “b” is from 0 to 7.  
/Sdd  
Scan device only on the PCI BUS #0 and device #dd  
The range for “dd” is from 0 to 20.  
/CCBSx  
Defines the maximum number of concurrent I/O that driver supports.  
The range for “x” is from 1 to 16.  
ASPI CD-ROM Driver Command Line Options  
INICD.SYS is a DOS device driver for supporting SCSI CD-ROM drives. It is the interface  
between MSCDEX.EXE (supplied by Microsoft®) and the physical CDROM drive.  
INICD.SYS is automatically loaded in the CONFIG.SYS start up file by the Initio  
DOSSETUP or SETUP programs. INICD.SYS requires that the Initio ASPI Manager be  
loaded. INICD.SYS can be loaded with either the DEVICE= or DEVICEHIGH= command.  
INICD.SYS can be found on INI-9XXXU/9XXXUW DRIVER DISK 1. Below is a list of  
command line options and examples.  
/D: /d: This option is used to specify the name of the device driver. The name specified  
must also be passed to MSCDEX.EXE on it’s command line (Using the same /D: or /d:  
option). The name specified must be 8 or less characters in length. Valid characters are  
the A-Z, a-z, 0-9 and underscore. The name must start with a letter.  
Examples:  
/D:INICD001  
/d:mscd001  
/d:MYCD01  
/T /t  
This option is used to specify a Time out value to be used when sending  
commands to a CDROM drive. If a CDROM drive does not respond to a command  
within the specified time out then the command will be aborted and an appropriate  
error message will be displayed. The time out value is specified in minutes. Valid values  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
MS-DOS/Windows 3.1x Driver Installation  
are 1-9 and D or d. The D or d values are used to Disable the time out mechanism. If  
the time out mechanism is disabled then faulty hardware can lock up the system.  
Examples:  
/T4  
/Td  
/TD  
/T1  
/X /x  
This option is used to exclude particular CD-ROM drives. Excluded CDROM  
drives are identified by specifying the host adapter, target id and lun. These values are  
spereated by a colon. Groups of CDROM drives (or wild cards) can also be identified.  
Below are examples of the different ways CDROM drives can be excluded:  
/X0:1:2  
/X0:2  
/X0  
This will exclude the drive on Host Adapter 0, with target ID 1  
and lun 2.  
This will exclude the drive on Host Adapter 0, with target ID 2  
and ANY lun  
This will exclude ALL drives on Host Adapter 0.  
SAMPLE CONFIG.SYS AND AUTOEXEC.BAT FILES  
These samples assume that the user has loaded the Initio drivers in the following  
directory: c:\iniaspi.  
Config.sys:  
DEVICEHIGH=c:\iniaspi\aspi910u  
DEVICEHIGH=c:\iniaspi\inicd.sys /D:INICD001  
Explanation:  
The first line loads the ASPI manager and the second line loads the CDROM driver  
specifying the device name INICD001.  
Autoexec.bat:  
Mscdex /D:INICD001  
Explanation:  
This line will load the Microsoft supplied mscdex.exe file instructing it to attach to the  
CD-ROM device driver INICD001.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
MS-DOS/Windows 3.1x Driver Installation  
ASPI Disk Driver Command Line Options  
INIDISK.SYS is a DOS block device driver for supporting SCSI fixed disks, removable  
disks and MO devices. INIDISK.SYS is automatically loaded in CONFIG.SYS start up file  
by the Initio DOSSETUP or SETUP programs. INIDISK.SYS requires that the Initio ASPI  
Manager be loaded. INIDISK.SYS can be loaded with either the DEVICE= or  
DEVICEHIGH= command. INICD.SYS can be found on the INI-9XXXU/9XXXUW DRIVER  
DISK 1. Below is a list of command line options and examples.  
/R /r  
This option specifies the number of logical drives to reserve for MO and  
removable disk devices. MO and removable disks media are capable of being parti-  
tioned just like a fixed disk. For every DOS partition on the media a logical DOS drive  
letter will be available. INIDISK.SYS will support as many logical drives as required (up to  
the maximum supported by DOS) based on the partitioning of the media that is present  
when your system boots. However, the media may be removed at any time and a new  
disk may be inserted. The new disk may have more (or less) partitions then the original  
disk. The /R /r option is used to reserved drive letters at start up in order to facilitate a  
disk change to a disk with more partitions than the original disk present at boot time.  
The value after the /R /r option determines how many drive letters will be reserved on a  
device basis. For example, if the user specifies a /R4 option and there are two removable  
devices attached to the SCSI bus, then a total of eight (8) drive letters will be reserved.  
/T /t  
This option is used to specify a Time out value to be used when sending  
commands to a SCSI drive. If a SCSI drive does not respond to a command within the  
specified time out then the command will be aborted and an appropriate error message  
will be displayed. The time out value is specified in minutes. Valid values are 1-9 and D  
or d. The D or d values are used to Disable the time out mechanism. If the time out  
mechanism is disabled then faulty hardware can lock up the system.  
Examples:  
/T4  
/Td  
/TD  
/T1  
/X /x  
This option is used to exclude particular SCSI drives. Excluded SCSI drives are  
identified by specifying the host adapter, target id and lun. These values are spereated  
by a colon. Groups of SCSI drives (or wild cards) can also be identified. Below are  
examples of the different ways SCSI drives can be excluded:  
/X0:1:2  
/X0:2  
This will exclude the drive on Host Adapter 0, with target ID 1  
and lun 2.  
This will exclude the drive on Host Adapter 0, with target ID 2  
and ANY lun  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
MS-DOS/Windows 3.1x Driver Installation  
/X0  
This will exclude ALL drives on Host Adapter 0.  
SAMPLE CONFIG.SYS  
These samples assume that the user has loaded the Initio drivers in the following  
directory: c:\iniaspi.  
Config.sys:  
DEVICEHIGH=c:\iniaspi\aspi910u  
DEVICEHIGH=c:\iniaspi\inicd.sys /R2  
Explanation:  
The first line loads the ASPI manager and the second line loads the SCSI disk driver  
specifying that a minimum of two drive letters be reserved for each MO and removable  
disk attached to the SCSI bus.  
ASPI Partition & Format Utility  
INIFDISK.EXE is a DOS ASPI partition and format utility. It requires the ASPI910U.SYS  
and INIDISK.SYS drivers to be loaded in order for it to function properly. INIFDISK.EXE is  
installed by the Initio DOSSETUP or SETUP programs. Upon invocation, the initial  
screen will have two windows. The top window will list all of the SCSI devices installed in  
the system. The user can highlight a particular device by using the up and down arrow  
keys. The bottom window will display information about the device that is currently  
highlighted in the top window. Inifdisk.exe can partition and format any SCSI storage  
device that is not being controlled by the BIOS, this includes SCSI disks, magnetic  
optical drives, and removable media devices. INIFDISK will display two screens in which  
the bottom portion will explain all commands possible in the top window.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
Microsoft Windows 95/95b (OSR2) Driver Installation  
Overview  
I/OHIGHWAY will support Microsoft Windows 95 and Windows 95B (OSR2) with the  
addition of a software driver. The installation procedure described here requires some  
experience in Windows 95 system setup and administration. The device driver is  
transferred from the INI-9XXXU/9XXXUW DRIVER DISK 1 to the hard drive where it is  
automatically initialized during the system boot routine.  
6
The following files are used for installation and will be found on the INI-9XXXU/9XXXUW  
DRIVER DISK 1:  
\WIN95\INI910U.MPD  
INI-9XXX SCSI Host Adapter Windows 95 miniport driver.  
\WIN95\INI910U.INF  
Windows 95 installation information file.  
Installation  
The INI-9XXX driver developed for Windows 95 is loaded during the system boot routine  
and will remain resident on the drive. This is accomplished by following one of the three  
installation procedures listed:  
• New Windows 95 and Windows 95B (OSR2) installation.  
• Adding the Initio Windows 95 device driver to an existing Windows 95 or Windows 95B  
(OSR2) system.  
• Updating INI910U.MPD device driver  
The procedures described to make changes to the system have distinct differences. It is  
strongly suggested that the selected procedure be read and understood before proceed-  
ing with the system configuration changes. Please read the instructions carefully.  
To determine which version of Windows 95 you have installed on your system,  
check the date of the KRNL32.DLL file located in your Windows directory. A file  
date of 07/11/95 belongs to Windows 95, first release; 12/31/95 belongs to Win-  
dows 95a or 95 with Service Pack 1; and 08/24/96 reflects Windows 95b or OSR2.  
New Windows 95/95a Installation  
These instructions will guide you through the installation of the Initio host adapter driver  
while installing Windows 95. Windows 95 will be installed from either a CD-ROM or floppy  
diskettes. It is important that the hardware and DOS 4.01 or higher have been installed  
successfully before proceeding further. If installing from a SCSI CD-ROM drive, it is impor-  
tant that the Initio ASPI driver, and CD-ROM driver be installed before proceeding further.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
Microsoft Windows 95/95b (OSR2) Driver Installation  
1 Access the Windows 95 CD-ROM from either the DOS prompt or from Microsoft  
Windows 3.x File Manager. Execute the SETUP.EXE program and follow the instruc-  
tions on your screen. If you are installing from floppy diskette, insert the Windows 95  
Setup Disk 1 in your floppy disk drive and boot your system. Follow the instructions  
on your screen.  
2 Once a Windows 95 session is established, use your installed mouse or the appropri-  
ate key strokes to select MY COMPUTER from the MAIN DESKTOP. Execute the  
following steps:  
• Select CONTROL PANEL from within the MY COMPUTER icon.  
• Select SYSTEM from within the CONTROL PANEL group  
• Select DEVICE MANAGER tab from within the SYSTEM group  
• Select the OTHER DEVICES category from within the DEVICE MANAGER listing.  
• Select the PCI-SCSI Bus Controller sub-category from within the OTHER DE-  
VICES listing.  
• In the Initio PCI-SCSI Bus Controller Properties window, select the DRIVER tab,  
then select “CHANGE DRIVER...”.  
• In the SELECT HARDWARE TYPE window, select SCSI CONTROLLERS.  
• In the SELECT DEVICE window, select “HAVE DISK...”.  
3 In the INSTALL FROM DISK window, enter the Initio Driver path name:  
• Insert the INI-9XXXU/9XXXUW DRIVER DISK 1 into drive A:  
• Type: A:\WIN95, select “OK”  
4 Select Initio INI-9XXXU/UW PCI SCSI Host Adapter, select “OK”, then “OK”  
again to install the INI910U.MPD driver onto your hard disk drive. It may be necessary to  
direct Windows to look for the driver in A:\win95 before the driver can be copied. This step may  
need to be repeated more than once.  
5 Following installation of the Initio INI-9XXXU/UW Windows 95 driver for all channels,  
reboot your system to activate the SCSI device driver.  
6 It is highly recommended that you Initio’s Windows 95 device driver has been  
properly installed by selecting MY COMPUTER from the desktop. Then select  
CONTROL PANEL:  
• Select SYSTEM from within the CONTROL PANEL group,  
• Select DEVICE MANAGER from within the SYSTEM group,  
• Select SCSI CONTROLLER from within the DEVICE MANAGER listing, and  
• Select Initio INI-9XXXU/UW PCI SCSI Host Adapter from within the SCSI  
CONTROLLER listing. If “This device is working properly” is displayed on your  
screen, the driver has been correctly installed.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
Microsoft Windows 95/95b (OSR2) Driver Installation  
Adding the Initio Driver to an Existing Windows 95/95a  
System  
These instructions will guide you through the installation of the Initio host adapter to an  
existing Windows 95 system. Windows 95 will automatically detect the presence of new  
hardware in Plug and Play compliant systems. It is important that the Initio hardware  
has been properly installed before proceeding further.  
1 Microsoft Windows 95 will detect the presence of new hardware upon boot-up and  
will display a dialog window titled NEW HARDWARE FOUND and PCI SCSI BUS  
CONTROLLERS will be highlighted.  
• Select: DRIVER FROM DISK PROVIDED BY HARDWARE MANUFACTURER,  
then “OK”  
• Select SCSI CONTROLLER from the list of available devices, then select “HAVE  
DISK...”  
2 In the INSTALL FROM DISK window that is displayed, enter the Initio Driver path  
name:  
Insert INI-9XXXU/9XXXUW DRIVER DISK 1 into drive A:  
Type: A:\WIN95, select “OK”  
3 Select Initio INI-9XXXU/UW PCI SCSI Host Adapter, select “OK”, then “OK” again  
to install the INI910U.MPD driver onto your hard disk drive. It may be necessary to direct  
Windows to look for the driver in A:\win95 before the driver can be copied. This step may need to be  
repeated more than once.  
4 This completes loading the Host Adapter Driver. You must now reboot your system to  
activate the SCSI device driver. .  
5 It is highly recommended that you verify Initio’s Windows 95 device driver by selecting  
MY COMPUTER from the desktop. Then select CONTROL PANEL:  
• Select SYSTEM from within the CONTROL PANEL group,  
• Select DEVICE MANAGER from within the SYSTEM group,  
• Select SCSI CONTROLLER from within the DEVICE MANAGER listing, and  
• Select the Initio INI-9XXXU/UW PCI SCSI Host Adapter from within the SCSI  
CONTROLLER listing. If “This device is working properly” is displayed on your  
screen, the driver has been correctly installed.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
Microsoft Windows 95/95b (OSR2) Driver Installation  
Updating the Initio Windows 95/95a Device Driver  
1 Once a Windows 95 session is established, use your installed mouse or the appropri-  
ate key strokes to select MY COMPUTER from the Main Desktop. Execute the  
following steps:  
• Select CONTROL PANEL from within the MY COMPUTER group.  
• Select SYSTEM from within the CONTROL PANEL group.  
2 • Select the DEVICE MANAGER tab from within the SYSTEM group.  
• Select the SCSI CONTROLLERS category from within the DEVICE MANAGER  
listing.  
• Select one of the Initio INI-9XXXU/UW PCI SCSI Host Adapter sub-categories  
from within the SCSI CONTROLLERS listing (or select any other INI-9100U/UW  
class of drivers if you are using an older Initio board).  
• In the INI-9XXX SCSI HOST ADAPTER PROPERTIES window, select the DRIVER tab,  
then select “CHANGE DRIVER...”.  
• In the SELECT DEVICE window, select “HAVE DISK...”.  
3 In the INSTALL FROM DISK window, enter the Initio Driver path name:  
• Insert the INI-9XXXU/9XXXUW DRIVER DISK 1 into drive A:  
• Type: A:\WIN95, select “OK”  
4 Select Initio INI-9XXXU/UW PCI SCSI Host Adapter, select “OK” to install the  
INI910U.MPD driver onto your hard disk drive.  
It may be necessary to direct Windows to look for the driver in A:\win95 before the driver can be copied.  
This step may need to be repeated more than once.  
This completes updating the Host Adapter Driver. Follow the on-screen directions to  
restart you computer and activate the new driver.  
It is highly recommended that you verify Initio’s Windows 95 device driver by selecting  
MY COMPUTER from the desktop. Then select CONTROL PANEL:  
• Select SYSTEM from within the CONTROL PANEL group,  
• Select DEVICE MANAGER from within the SYSTEM group,  
• Select SCSI CONTROLLER from within the DEVICE MANAGER listing, and  
• Select the Initio INI-9XXXU/UW PCI SCSI Host Adapter from within the SCSI  
CONTROLLER listing. If “This device is working properly” is displayed on your  
screen, the driver has been correctly installed.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
Microsoft Windows 95/95b (OSR2) Driver Installation  
New Windows 95B (OSR2) Installation  
These instructions will guide you through the installation of the Initio host adapter driver  
while installing Windows 95B (OSR2). Windows 95B will be installed from either a CD-  
ROM or floppy diskettes. It is important that the hardware and DOS 4.01 or higher have  
been installed successfully before proceeding further. If installing from a SCSI CD-ROM  
drive, it is important that the Initio ASPI driver, and CD-ROM driver be installed before  
proceeding further.  
1 Access the Windows 95B CD-ROM either from the DOS prompt or from Microsoft Win-  
dows 3.x File Manager. Execute the SETUP.EXE program and follow the instructions on  
your screen. If you are installing from floppy diskette, insert the Windows 95 Setup Disk  
1 in your floppy disk drive and boot your system. Follow the instructions on your  
screen.  
2 Once a Windows 95 session is established, use your installed mouse or the appropri-  
ate key strokes to select MY COMPUTER from the MAIN DESKTOP. Execute the  
following steps:  
• Select CONTROL PANEL from within the MY COMPUTER group  
• Select SYSTEM from within the CONTROL PANEL group,  
• Select DEVICE MANAGER tab from within the SYSTEM group  
• Select the OTHER DEVICES category from within the DEVICE MANAGER listing  
• Select one of the PCI-SCSI Bus Controller sub-category from within the OTHER  
DEVICES listing  
• In the Initio PCI-SCSI Bus Controller Properties window, select the DRIVER tab,  
then select “UPDATE DRIVER...”  
• Insert INI-9XXXU/9XXXUW DRIVER DISK 1 into drive A:  
• Select YES, click Next, and Windows will search for the driver  
• Select the OTHER LOCATION  
• Type A:\WIN95, then select “OK”  
• Select “FINISH”  
• At window “Insert Disk labled INI-9XXXU/9XXXUW driver” , select “OK”  
• At window titled “Copying file”, replace the highlighted directory path with  
A:\WIN95, then select “OK” this will complete loading the INI910U.MPD driver  
onto your hard disk drive.  
3 Following installation of the Initio INI-9XXXU/UW Windows 95 driver, reboot your sys-  
tem to activate the SCSI device driver.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
Microsoft Windows 95/95b (OSR2) Driver Installation  
4 It is highly recommended that you verify Initio’s Windows 95 device driver by selecting  
MY COMPUTER from the desktop. Then select CONTROL PANEL:  
• Select SYSTEM from within the CONTROL PANEL group,  
• Select DEVICE MANAGER from within the SYSTEM group,  
• Select SCSI CONTROLLER from within the DEVICE MANAGER listing, and  
• Select the Initio INI-9XXXU/UW PCI SCSI Host Adapter from within the SCSI  
CONTROLLER listing. If “This device is working properly” is displayed on your  
screen, the driver has been correctly installed.  
This completes loading the Host Adapter Driver, follow the on-screen directions to com-  
plete the Windows 95 installation. Exit and reboot the system to activate the device driver.  
Adding the Initio Driver to an Existing Windows 95B  
(OSR2) System  
These instructions will guide you through the installation of the Initio host adapter to an  
existing Windows 95 system. Windows 95 will automatically detect the presence of new  
hardware in Plug and Play compliant systems. It is important that the Initio INI-9XXX  
hardware has been properly installed before proceeding further.  
1 Microsoft Windows 95 will detect the presence of new hardware upon boot-up and  
will display a dialog window titled “update Device driver wizard”  
2 Insert the INI-9XXXU/9XXXUW DRIVER DISK 1 into floppy drive,:  
•Select “NEXT”  
•Select the “OTHER LOCATION”  
•Type A:\Win95, then select “OK”  
•Select “FINISH”  
•At window “Insert Disk labled INI-9XXXU/9XXXUW driver”, select “OK”  
•At window titled “Copying file”, replace the highlighted directory path with  
A:\Win95, then select “OK” this will complete loading the INI910U.MPD driver  
onto your hard disk drive. Restart your computer.  
3 It is highly recommended that you verify Initio’s Windows 95 device driver by selecting  
MY COMPUTER from the desktop. Then select CONTROL PANEL:  
•Select SYSTEM from within the CONTROL PANEL group,  
•Select DEVICE MANAGER from within the SYSTEM group,  
•Select SCSI CONTROLLER from within the DEVICE MANAGER listing, and  
•Select the Initio INI-9XXXU/UW PCI SCSI Host Adapter entries from within the  
SCSI CONTROLLER listing. If “This device is working properly” is displayed on  
your screen, the driver has been correctly installed.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
Microsoft Windows 95/95b (OSR2) Driver Installation  
Updating the Initio Windows 95B (OSR2) Device Driver  
1 Once a Windows 95 session is established, select MY COMPUTER from your desktop.  
Execute the following steps:  
• Select CONTROL PANEL from within the MY COMPUTER group  
• Select SYSTEM from within the CONTROL PANEL group  
• Select the DEVICE MANAGER tab from within the SYSTEM group  
• Select the SCSI CONTROLLERS category from within the DEVICE MANAGER listing  
• Select the Initio INI-9XXXU/UW PCI SCSI Host Adapter sub-categories from  
within the SCSI CONTROLLERS listing (or any other INI-9100U/UW class of drivers if  
you are using an older Initio product)  
2 In the INI-9XXXU/9XXXUW SCSI HOST ADAPTER PROPERTIES window, select the  
DRIVER tab, then select “UPDATE DRIVER...”  
• Select “Next”  
• Select the “OTHER LOCATION”  
• Type A:\WIN95, then select “OK”  
• Select “FINISH”  
• At prompt“Insert Disk labled INI-9XXXU/9XXXUW driver ,” select “OK”  
• At prompt “Copying file”, replace the highlighted directory path with A:\Win95,  
then select “OK.” This will complete loading the INI910U.MPD driver onto your hard  
disk drive.  
This completes updating the Host Adapter Driver. Follow the on-screen directions to  
restart you computer and activate the new driver.  
It is highly recommended that you verify Initio’s Windows 95 device driver by selecting  
MY COMPUTER from the desktop. Then select CONTROL PANEL:  
• Select SYSTEM from within the CONTROL PANEL group,  
• Select DEVICE MANAGER from within the SYSTEM group,  
• Select SCSI CONTROLLER from within the DEVICE MANAGER listing, and  
• Select the Initio INI-9XXXU/UW PCI SCSI Host Adapter entries from within the  
SCSI CONTROLLER listing. If “This device is working properly” is displayed on  
your screen, the driver has been correctly installed.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
Microsoft Windows NT Driver Installation  
Overview  
I/OHIGHWAY will support Windows NT v3.5x/4.0 with the addition of a software driver. A  
software driver allows the host computer the ability to transfer data over the SCSI bus.  
The device driver for Windows NT is copied from the Initio driver installation diskette to  
your hard drive where it is loaded onto the computing system during installation.  
7
The following files are used for installation and may be found on the INI-9XXXU/9XXXUW  
DRIVER DISK 1:  
\WINNT\INI910U.SYS  
\WINNT\TXTSETUP.OEM  
\WINNT\OEMSETUP.INF  
INI-9XXX SCSI Host Adapter Windows-NT miniport driver.  
Script file for installing INI910U.SYS during the text setup phase.  
Script file for installing INI910U.SYS during the windows phase.  
Installation  
The INI-9XXX driver developed for Windows NT will be installed on the hard drive used  
for system initialization. The driver is loaded during the system boot routine and will  
remain resident on the drive. This is accomplished by following one of the two installa-  
tion procedures listed:  
• New Windows NT installation  
• Adding or updating the INI-9XXX Host Adapter Driver to an existing Windows NT  
System  
The procedures described to make changes to the system have distinct differences. It is  
strongly suggested that the selected procedure be read and understood before proceed-  
ing with the system configuration changes. Please read the instructions carefully.  
New Windows NT Installation  
These instructions will guide you through the installation of the Initio host adapter driver  
while installing Windows NT 4.0. Windows NT will be installed from either floppy  
diskettes or CD-ROM. The Windows NT driver is located on the INI-9XXXU/9XXXUW  
DRIVER DISK 1. It is important that the hardware has been installed successfully before  
proceeding further.  
1
If you are installing Windows NT from floppy diskettes, locate the Windows NT  
Disk 1 for Floppy Installation. Make a backup copy of this diskette before  
installation.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32  
Microsoft Windows NT Driver Installation  
2
If you are installing Windows NT from a CD version, locate the Windows NT  
Setup Disk for CD-ROM Installation. Make a backup copy of this diskette before  
installation.  
3
4
Insert the backup Windows NT Setup disk into drive A: and turn on your com-  
puter.  
Follow the instructions on the screen until you come to a window titled:  
”WINDOWS NT WORKSTATION SETUP” (for servers, it will read “WINDOWS NT SERVER  
SETUP”).  
• Press “ENTER” to continue setting up Windows NT.  
• Select “S” to skip mass storage detection.  
• Select “S” to configure additional SCSI adapters.  
5
6
When prompted by the Windows NT installation, scroll down the list and select  
“OTHER (Requires disk provided by a hardware manufacturer)” from the  
list of Additional SCSI Adapters. A message will appear on screen stating to:  
• Remove diskette in drive A and set it aside.  
• Insert INI-9XXXU/9XXXUW DRIVER DISK 1 and press <ENTER>.  
• Select: Initio INI-9XXX SCSI Host Adapter and press <ENTER>.  
The Initio host adapter driver is now installed The on-screen instructions will  
continue for a complete installation of Windows NT. Refer to your Windows NT  
users manual for completion of the operating system installation procedure.  
Adding or updating the Initio driver to an existing Win-  
dows NT system:  
For computer systems using other SCSI host adapters or an IDE drive to provide the  
system boot routine, these instructions will guide you through the INI-9XXX host  
adapter driver installation. The Windows NT driver will be found on the INI-9XXXU/  
9XXXUW DRIVER DISK 1. It is important that the SCSI bus hardware and Windows NT  
are installed and configured before proceeding further.  
1 Once a Windows NT session is established, use your installed mouse or the appropri-  
ate key strokes to select MY COMPUTER from the Main Desktop. Execute the  
following steps:  
• Select CONTROL PANEL from within the MY COMPUTER group.  
• Select SCSI ADAPTERS from within the CONTROL PANEL group.  
2 Select the DRIVERS tab from within the SCSI ADAPTERS group.  
• In the DRIVERS window, select “ADDꢀ”  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
Microsoft Windows NT Driver Installation  
3 In the INSTALL DRIVER window, select “HAVE DISK...”.  
4 In the INSTALL FROM DISK window that is displayed, enter the Initio Driver path  
name:  
• Insert INI-9XXXU/9XXXUW DRIVER DISK 1 into drive A:  
• Type: A:\WINNT, select “OK”  
5 Select Initio INI-9XXXU/UW PCI SCSI Host Adapter, select “OK” to install the  
INI910U.SYS driver onto your hard disk drive.  
6 In the WINDOWS NT SETUP window that is displayed, enter the Initio Driver path  
name to continue:  
• Type: A:\WINNT, select “CONTINUE”  
7 This completes updating the Host Adapter Driver. Follow the on-screen directions to  
restart you computer and activate the new driver  
8 It is highly recommended that you verify Initio’s Windows NT device driver has been  
properly installed by selecting MY COMPUTER from the desktop. Then select  
CONTROL PANEL:  
• Select SCSI ADAPTERS from within the CONTROL PANEL group,  
• Select Initio INI-9XXXU/UW PCI SCSI Host Adapter from within the SCSI  
CONTROLLER listing. If “This device is working properly” is displayed on your  
screen, the driver has been correctly installed.  
Installing a new Windows NT system and Initio driver  
without floppy disks  
For computer systems installing or upgrading to Windows NT from a floppyless setup  
such as a share on your network, these instructions will guide you through the INI-  
9XXXU/9XXXUW host adapter driver installation. The Windows NT drivers are located on  
the INI-9XXXU/9XXXUW DRIVER DISK 1. It is important that the hardware has been  
installed successfully before proceeding further.  
1
Execute a floppyless setup as described by the Windows NT System Administrator’s  
Guide  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
34  
Microsoft Windows NT Driver Installation  
2
When SETUP begins to load, the screen will turn from black to blue with the text  
“SETUP IS INSPECTING YOUR COMPUTER’S HARDWARE CONFIGURATIONꢀ” at the  
top  
• Press the F6 key to interrupt this process. You will have two seconds in which to  
press this key  
• Follow the instructions on the screen until you are asked to specify a SCSI driver.  
3
4
Insert the INI-9XXXU/9XXXUW DRIVER DISK 1 into your local floppy disk drive,  
and press <ENTER>.  
• Select: Initio INI-9XXXU/UW PCI SCSI Host Adapter  
The Initio host adapter driver is now installed  
The on-screen instructions will continue for a complete installation of Windows NT.  
Refer to your Windows NT System Administrator’s Guide for completion of the operating  
system installation procedure.  
Installing a new Windows NT system from a Bootable CD  
For computer systems installing or upgrading to Windows NT from a bootable CD, these  
instructions will guide you through the INI-9XXXU/9XXXUW host adapter driver installa-  
tion. The Windows NT driver will be found on the INI-9XXXU/9XXXUW DRIVER DISK 1.  
It is important that the hardware has been installed successfully before proceeding  
further.  
1 Boot your system from a Windows NT CD.  
2 When initial boot screen (Black and white screen prior to blue screen) shows the  
message, “Setup is inspecting your computers hardware configuration,” press F6.  
3 A setup screen will appear asking which drivers you wish to use.  
4 Press the appropriate key to add driver and select other.  
5 Windows NT will prompt you for a manufacturer’s supplied disk.  
6 Insert the Initio manager set floppy (marked INI-9XXXU/9XXXUW DRIVER DISK 1) and  
press ENTER. The host adapter should be recognized by Windows NT and the driver  
will be allowed to load. The operating system will continue loading and should  
recognize the hard drives.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
Novell NetWare Driver Installation  
Overview  
I/OHIGHWAY will support Novell NetWare 386 V4.XX or V3.1X with the addition of a  
software driver. The installation procedure described here requires some experience in  
Novell system setup and administration. The device driver is transferred from the INI-  
9XXXU/9XXXUW DRIVER DISK 1 to the hard drive where it is automatically initialized  
during the system boot routine. The device drivers listed can support NetWare versions  
described after the Initio file name:  
8
\NETWARE\V31X\INI910U.DSK  
\NETWARE\V31X\ASPITRAN.DSK  
\NETWARE\V4X\INI910U.DSK  
\NETWARE\V4X\INI910U.DDI  
\NETWARE\V4X\ASPITRAN.DSK  
\NETWARE\HAM\INI9100.HAM  
\NETWARE\HAM\INI9100.DDI  
Initio Novell adapter driver for V3.1X  
ASPI transport layer driver for V3.1X  
Initio Novell adapter driver for V4.X or later  
Device driver installation file  
ASPI transport layer driver for V4.X or later  
HAM device driver  
HAM device driver installation file  
Installation  
The drivers developed by Initio for NetWare will be installed on the disk drive used for  
NetWare system initialization. It is strongly recommended that the selected procedure be  
read and understood before continuing with the system configuration or change. Please  
read the instructions carefully.  
New IntraNetWare Installation  
Drivers for the Initio host adapter may be found on the INI-9XXXU/9XXXUW DRIVER  
DISK 1. In most cases you will load the drivers during a new installation of NetWare from  
CD-ROM. The driver is loaded during the NetWare Server Installation procedure. The  
NetWare installation program will prompt you for the required parameters as the installa-  
tion procedure progresses. It is highly recommended that you have a copy of the Novell  
NetWare Installation and Upgrade Manual for reference.  
1 At the MS-DOS prompt for CD-ROM installation, change directories to where the  
installation files are located.  
e.g., d:\ <ENTER>  
2 Type INSTALL <ENTER> to initialize the installation routine  
3 Select installation Language. <ENTER>.  
4 Select NetWare Server Installation <ENTER>  
5 Select product type <ENTER>  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
36  
Novell NetWare Driver Installation  
6 Select installation type. <ENTER>  
7 Enter server name when prompted <ENTER>  
At this point the boot files will be copied to the hard drive.  
8 After the files are finished being copied you may encounter the following message:  
Install found the following hardware but found  
More than one driver supporting this hardware  
PCI.XXXX.XXXX.XXXX.XXXX.XX  
Press <Enter> for a list of drivers to choose  
From or <F3> to continue without selecting  
Press <F3> to continue. Repeat if this screen is shown again.  
9 A screen listing the drivers will be displayed. INI9100 will be listed as the selected  
driver. This completes loading the Host Adapter Driver, Follow the on-screen direc-  
tions to complete the Novell NetWare installation.  
This will load the HAM driver. If a DSK driver is required or an updated HAM driver is  
needed it is recommended that you complete the installation and use NetWare’s  
INSTALL utility to update/change the driver.  
Adding the Initio driver to an existing IntraNetWare sys-  
tem  
1 To begin the installation you will need to change the directory to the location of the  
server and initialize the network server, e.g.,  
Type CD \ NWSERVER <ENTER>  
Type SERVER <ENTER>  
2 At the NetWare prompt, Type LOAD INSTALL <ENTER>.  
3 Select Driver Options from the window by highlighting it using the UP or DOWN  
ARROW keys, press <ENTER>  
• Select Configure disk and storage device drivers from the window by high  
lighting it using the UP or DOWN ARROW keys, press <ENTER>  
4 Highlight Discover and load additional drivers and press <ENTER>  
5 NetWare will load INI9100.HAM modify the STRATUP.NCF file to reflect the new  
changes.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
Novell NetWare Driver Installation  
Upgrading/Changing Driver on an Existing IntraNetWare  
Server  
1
To begin the you will need to change the directory to the location of the server and  
initialize the network server, e.g.,  
Type CD \ NWSERVER <ENTER>  
Type SERVER <ENTER>  
2
3
At the NetWare prompt, Type LOAD INSTALL <ENTER>.  
Select Driver Options from the window by highlighting it using the UP or DOWN  
ARROW keys, press <ENTER>  
• Select Configure disk and storage device drivers from the window by high-  
lighting it using the UP or DOWN ARROW keys, press <ENTER>  
4
5
Highlight Deselect a selected driver and press <ENTER>  
Highlight the driver you wish to replace/upgrade and press <ENTER>  
Repeat steps 4 and 5 for each instance of the driver  
6
When all of the drivers you wish to upgrade/replace have been removed highlight  
Select an additional driver and press <ENTER>  
7
8
9
Press <INS> followed by <F3>  
Enter the location path of the drivers A:\  
Select the driver you wish to load INI9100.HAM or INI910U.DSK and press  
<ENTER>  
If the HAM driver(s) are being used proceed to step 10. If you use the DSK driver  
the upgrade is complete and you may exit the install utility.  
10 Highlight Select and modify parameters and press <ENTER>  
Enter the slot number and press <F10> to continue  
11 Highlight Save parameters and continue and press <ENTER>  
12 Repeat steps 6 through 11 for each additional adapter installed  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
38  
Novell NetWare Driver Installation  
Device driver command line options  
The Initio device drivers support command line switches to optimize driver performance.  
However, in certain situations some driver optimization may be advantageous to system  
performance.  
NetWare offers two means of entering command line switches. One method is for  
session usage and needs to be entered each time the system is rebooted.  
Load (Pathname) ini910u [Driver Config Option]  
The second method listed is for permanent installation. In startup.ncf you can include  
the following statement.  
Load (Pathname) ini910u [Driver Config Option]  
or  
Load (Pathname) INI9100 [Driver Config Option]  
Driver Config Options:  
/V  
Verbose Mode provides detail information about driver on system command line  
when driver is initialized.  
/!V  
Non Verbose Mode (default)  
/L  
Driver assumes that all targets have more than one LUN  
Driver assumes that all targets only have LUN 0 (default)  
Target enable mask WORD (Default scan all targets)  
Scan device only on PCI BUS #b, PCI DEVICE #dd  
Scan all the devices on PCI BUS #b (from 0 to 7)  
Specifies maximum number of tag commands per target (default 4)  
No tag  
/!L  
/T:xxxx  
/B:b,dd  
/B:b  
/Q:q  
/!Q  
/WR  
/!WR  
/R  
Read after write, hardware verify  
Not verified (default)  
Support removable media (default)  
/!R  
Will not support removable media  
/D  
/!D  
Enable support for fixed disk drive (default)  
Disable support for fixed disk drive  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
IBM OS/2 Driver Installation  
Overview  
The I/OHIGHWAY OS/2 driver will support OS/2, 3.0 & 4.0. The device driver for OS/2 is  
copied from the INI-9XXXU/9XXXUW DRIVER DISK 1 to your hard drive where it is  
initialized during boot-up.  
9
The installation of Initio device drivers to support OS/2 include the following software  
files and may be found on the INI-9XXXU/9XXXUW DRIVER DISK 1:  
\OS2\INI910U. ADD  
\OS2\INI910U.DDP  
INI-9XXX SCSI Host Adapter OS/2 driver.  
Script file for installing INI910U.ADD  
Installation  
The INI-9XXX driver developed for OS/2 will be installed on the disk drive used for  
system initialization. The driver is loaded during the system boot routine and will remain  
resident on the drive. Installation of the drivers can be accomplished by following one  
of the procedures listed:  
• New OS/2 Installation  
• Adding INI-9XXX host adapter to existing OS/2  
The steps used to install the Initio drivers have different system requirements that may  
affect basic operation if not installed properly. It is strongly suggested that the selected  
procedure be read and understood before proceeding. Please read all instructions  
carefully.  
New OS/2 installation:  
These instructions will guide you through the Initio OS/2 device driver and OS/2 installa-  
tion at the same time. The program can be installed from floppy diskettes or from CD-  
ROM. The OS/2 driver for the INI-9XXX will be found on the INI-9XXXU/9XXXUW DRIVER  
DISK 1. It is important that the INI-9XXX hardware has been installed successfully before  
proceeding further.  
1 Make a duplicate copy of OS/2 Diskette 1 using a blank diskette and label it as “OS/2  
Diskette 1 for INI-9XXX”.  
2 Copy the INI910U.ADD file from the INI-9XXXU/9XXXUW DRIVER DISK 1 (OS/2  
subdirectory) to the root directory on the “OS/2 diskette 1 for INI-9XXX”.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
40  
IBM OS/2 Driver Installation  
3 Using an appropriate text editor modify the CONFIG.SYS on the OS/2 Diskette 1 for  
INI-9XXX to include the new Initio driver.  
Enter: BASEDEV=INI910U.ADD and save the file.  
4 Insert the Installation Diskette into drive A: and turn on your computer. This will  
begin the OS/2 installation and establish an OS/2 bootable hard drive.  
5 When prompted, insert the “OS/2 Diskette 1 for INI-9XXX.” Follow the on-screen  
instructions to continue.  
6 You have completed the Initio device driver installation for OS/2. Follow the on-screen  
instructions and OS/2 manual for a complete description of OS/2 installation.  
Adding the Initio driver to an existing OS/2 system  
For computer systems using other SCSI host adapters or an IDE device to provide the  
system boot routines, these instructions will guide you through INI-9XXX host adapter  
driver installation. The OS/2 driver will be found on the INI-9XXXU/9XXXUW DVR DISK 1.  
It is important that the SCSI bus hardware and OS/2 are installed correctly before proceed-  
ing further.  
1
2
Once an OS/2 session is established, insert the INI-9XXXU/9XXXUW DRIVER DISK 1  
into your floppy drive.  
By using your installed mouse, or by using the appropriate key strokes, select  
DEVICE DRIVER INSTALL from the SYSTEM SETUP group.  
3
4
5
6
Select CHANGE source directory to read as the root directory.  
Select OS2 and select SET.  
Select DESTINATION DIRECTORY.  
Select CHANGE destination directory to any existing OS/2 directory or accept the  
default.  
7
8
9
Select SET.  
From the DEVICE DRIVER INSTALLATION GROUP select INSTALL.  
Select INITIO INI-9XXX Device Driver for OS/2 select “OK”.  
10 Select EXIT to install the OS/2 device driver. Exit and reboot the system to activate  
the device driver.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
41  
IBM OS/2 Driver Installation  
Device driver command line options  
The Initio device drivers support command line switches to optimize driver performance.  
Device drivers normally require no further information to work effectively. However, in  
certain situations some driver optimization may be advantageous to system perfor-  
mance. From inside the CONFIG.SYS file use the following format to edit the file.  
The standard format for command line switches is:  
BASEDEV = INI910U.ADD [Driver Config Option]  
Driver Config Options:  
/V  
Verbose Mode provides detail information about driver on system command line  
when driver is initialized.  
/!V  
Non Verbose Mode (default)  
/ET  
Driver assumes that all targets have more than one LUN  
Driver assumes that all targets only have LUN 0 (default)  
Target enable mask WORD (Default scan all targets) in hex format  
Scan device only on PCI BUS #b, DEVICE #dd (in decimal format)  
Scan all the devices on PCI BUS #b (from 0 to 7)  
Assigns adapter number based on BIOS address  
Enable direct access storage device (DASD) support  
Disable DASD manager support  
/!ET  
/T:hhhh  
/B:b,dd  
/B:b  
/A:n  
/DM:t,t,t  
/!DM:t,t,t  
/SM:t,t,t  
/!SM:t,t,t  
/Q:q  
Enable SCSI manager support  
Disable SCSI manager support  
Specifies maximum number of tag commands per target  
No tag  
/!Q  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
SCO Unix Driver Installation  
Overview  
The I/OHIGHWAY SCO UNIX device driver will support SCO UNIX System V/386 Release  
3.2v4.0 or later, SCO Open Desktop v2.0, v3.0 or later, and SCO Open Server Release 3.0 &  
5.0.x. The device driver is transferred from the floppy diskette to the hard drive where it’s  
loaded during system initialization.  
10  
The installation of Initio device drivers to support SCO UNIX include the following  
software files and may be found on the INI-9XXXU/9XXXUW DRIVER DISK 2.  
Driver.o  
Space.c  
Device driver object file  
Device driver definition file  
Reference Documentation:  
• SCO UNIX documentation, installation and user’s guide  
• The systems setup and installation guide  
• The documentation for system peripherals  
• Initio documentation for the SCSI host adapter  
Installation  
The SCO UNIX drivers developed by Initio will be installed on the disk drive used for sys-  
tem initialization. It is strongly suggested that the selected procedure be read and under-  
stood before continuing with the system configuration or change. Please read the instruc-  
tions carefully.  
Updating interrupts and hardware settings  
The following interrupt configuration settings are suggested as the most effective means  
of providing a controller interrupt to the host adapter:  
• Host Adapter interrupt levels available are 9,11, 15, (IRQ 11 is recommended)  
• Avoid using interrupt 10 as the controller interrupt.  
• Set first SCSI disk ID to 0 (first time install requirement)  
• Set tape target ID to 2. (If tape is in use)  
• Set CD-ROM target ID to 5. (If CD-ROM is in use)  
Please Refer to your system documentation to set the interrupt levels and your peripheral  
documentation for help in setting SCSI IDs.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
44  
SCO Unix Driver Installation  
Installing the Initio driver in a new SCO UNIX system  
1 Insert the SCO UNIX N1 boot disk into the floppy drive and turn on the system. At the  
SCO UNIX boot prompt, type: link < ENTER >.  
2 The system will ask you what packages you want linked to the system; type: i91u <  
ENTER >. The system at this point will boot into SCO UNIX. Please refer to the SCO  
UNIX Documentation for additional information. When prompted by the installation,  
insert the INI-9XXXU/9XXXUW DRIVER DISK 2 diskette into your floppy drive; Press <  
ENTER >  
3 Please refer to the SCO UNIX Documentation for additional information. You have  
completed the installation of the SCO UNIX driver.  
Adding the Initio driver to an existing SCO UNIX system  
1 Insert the INI-9XXXU/9XXXUW DRIVER DISK 2 diskette into your floppy drive.  
2 Type: “installpkg” under the command prompt, <ENTER>  
3 The system will ask you what packages you wish to install.  
Type: i91u < ENTER >  
4 Change the directory and rebuild the UNIX kernel:  
• cd /etc/conf/cf.d < ENTER >  
• . /link_unix  
< ENTER >  
5 You have completed the link procedure for the Initio device driver. Exit and reboot  
the system.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45  
SCO Unix Driver Installation  
Changing to the INI-9XXX as the bootable host adapter:  
1 Insert the INI-9XXXU/9XXXUW DRIVER DISK 2 diskette into floppy drive.  
2 Type: “installpkg” under command prompt and press <ENTER>. The system will  
ask you what packages you want to install.  
• Type: i91u <ENTER>  
3 Change the mscsi file:  
• cd /etc/conf/cf.d  
• cp mscsi mscsi.bak < ENTER >  
• vi mscsi < ENTER >  
< ENTER >  
In the example below, The XXXX would be replaced with i91u.  
ha  
attach  
number ID  
lun  
XXXX Stp  
XXXX Sdsk  
XXXX Srom  
0
0
0
2
0
5
0
0
0
4 Rebuild the UNIX kernel:  
• . /link_unix < ENTER >  
5 You have completed the link procedure for the Initio device driver. Exit and reboot  
the system.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
47  
SCO UnixWare Driver Installation  
Overview  
The I/OHIGHWAY SCO UnixWare device driver will support UnixWare 2.x. The device driver  
is transferred from the floppy diskette to the hard drive where it is loaded during system  
initialization.  
11  
The installation of Initio device drivers to support SCO UnixWare may be found on the  
INI-9XXXU/9XXXUW DRIVER DISK 2.  
Installation  
The SCO UnixWare drivers developed by Initio will be installed on the disk drive used for  
system initialization. It is strongly suggested that the selected procedure be read and  
understood before continuing with the system configuration or change. Please read the  
instructions carefully.  
Updating interrupts and hardware settings  
The following interrupt configuration settings are suggested as the most effective means  
of providing a controller interrupt to the host adapter:  
• Host adapter interrupt level must be set to IRQ 10 for proper installation of the  
Initio driver.  
Please refer to your system documentation to set the interrupt levels and your periph-  
eral documentation for help in setting SCSI IDs.  
Installing the Initio driver in a new UnixWare system  
Drivers for the host adapter may be found on the INI-9XXXU/9XXXUW DRIVER DISK 2.  
In most cases you will load the drivers during a new installation of UnixWare from CD-  
ROM. The driver is loaded during the early stages of the installation procedure. The  
UnixWare installation program will prompt you for the required parameters as the  
installation procedure progresses. It is highly recommended that you have a copy of the  
SCO UnixWare Installation Handbook and SCO UnixWare System Owner Handbook for  
reference.  
1 Insert the “SCO UNIXWARE INSTALLATION DISKETTE” into the floppy drive and turn on  
the computer. Follow the on-screen installation instructions.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
48  
SCO UnixWare Driver Installation  
2 When prompted to INSTALL HOST BUS ADAPTER DRIVERS, insert the INI-9XXXU/  
9XXXUW DRIVER DISK 2 into drive A: press <Enter>.  
3 When prompted to INSTALL ANOTHER HBA DISKETTE, press <ENTER> to con-  
tinue.  
4 Follow the directions on screen until you come to a window titled: Loading Initio INI-  
9XXX Host Adapter.  
• Select CONTINUE INSTALLATION.  
• Select CONTINUE INSTALLATION again.  
5 This completes loading the host adapter driver. Follow the on-screen directions to  
complete the SCO UnixWare installation. For further information regarding UnixWare  
installation, refer to the SCO UnixWare Installation Handbook.  
Adding the Initio driver to an existing UnixWare system  
1 Once a UnixWare session is established and a command prompt is ready, type (recall  
that UnixWare is case sensitive):  
• cp /stand/unix /stand/unix.org , press <ENTER>  
• pkgadd -d diskette1 , press <ENTER>  
2 Select i910u ihv hba from the list of available host drivers, press <ENTER>.  
3 If the INI-9XXX is intended to be the bootable host adapter, the next step to updating  
the driver will require a revision to the I910u file. These instructions will guide you  
through changing the current software settings for UnixWare to establish the INI-9XXX  
as the host adapter for your boot device:  
• At the system command prompt, type  
• cd /etc/conf/sdevice.d  
• Use “vi” or another editor to modify the file I910u by adding a line  
• locate the line $version2  
• edit the file by adding the line $static immediately following $version2.  
• Rebuild the UnixWare kernel by completing the following steps at the command  
prompt :  
• /etc/conf/bin/idbuild -B <ENTER>  
• cp /etc/conf/cf.d/unix /stand/unix <ENTER>  
• cd / <ENTER>  
• shutdown -g0 ( 0 is Zero ) <ENTER>  
• Y <ENTER>  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
49  
SCO UnixWare Driver Installation  
4 If the host adapter is NOT intended to be bootable, these instructions will guide you  
through changing the current software settings for UnixWare to establish the INI-9XXX  
as a non-bootable host adapter for your device:  
• At the system command prompt, type  
• /etc/conf/bin/idbuild -M i910u <ENTER>  
• cd / <ENTER>  
• shutdown -g0 ( 0 is Zero ) <ENTER>  
• Y <ENTER>  
5 Exit the UnixWare program and reboot your system to initialize the new device driver  
to control INI-9XXX.  
Using Multiple Host Adapters  
UnixWare is capable of supporting up to eight SCSI busses. If you choose to use multiple  
host adapters in your system, verify that each host adapter shared interrupt level is set to  
IRQ10. Please refer to your system documentation to set the interrupt levels.  
Space for each host adapter in the system is configured and allocated by a separate line in  
the file /ETC/CONF/SDEVICE.D/I910U.  
1 Verify that Y is selected in the second field at the line starting at I910u in the file /ETC/  
CONF/SDEVICE.D/I910U for each INI-9XXX in the system.  
UnixWare will automatically rebuild the kernel when an additional INI-9XXX is detected.  
Removing the Initio driver from a UnixWare system  
1 Once a UnixWare session is established and a command prompt is ready, type (recall that UnixWare  
is case sensitive):  
• Type: /etc/conf/bin/idinstall -d i910u <ENTER> to delete the following files:  
/etc/conf/mdevice.d/i910u  
/etc/conf/sdevice.d/i910u  
/etc/conf/pack.d/i910u/driver.o  
/etc/conf/pack.d/i910u/space.c  
/etc/conf/pack.d/i910u/disk.cfg  
/etc/conf/pack.d/i910u/disk.cfg  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
50  
SCO UnixWare Driver Installation  
2 Then rebuild the UnixWare kernel by executing the following commands at the system prompt:  
/etc/conf/bin/idbiuld -B -K <ENTER>  
/cp /etc/conf/cf.d/unix /stand/unix <ENTER>  
cd/ <ENTER>  
shutdown -g0 (where 0 is Zero) <ENTER>  
Y <ENTER>  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
51  
Troubleshooting  
In the following section you will find commonly asked questions and answers to problems  
encountered during the installation of your host adapter.  
Question: Why isn’t the INI-9XXX banner “!!! Press <CRTL><I> for SmartSCSI Setup Utility  
!!!” displayed when I power up the host system?  
Answer:  
Verify that all cabling to the host adapter is installed correctly, refer to the hardware  
installation section of this manual.  
Question: On boot-up the message “SCSI BIOS Installed” is displayed, but my system hangs.  
Answer:  
Verify that the CMOS interrupt structure is set to INTA and the CMOS IRQ level  
matches the jumper settings on the motherboard. Refer to your PC user manual.  
Question: On boot-up, not all the peripherals are scanned and recognized.  
Answer:  
Verify that each of the SCSI devices on the bus has its own distinct SCSI ID number  
and all peripherals are receiving power. Refer to your peripheral manual for informa-  
tion regarding changing SCSI ID’s.  
Verify the SCSI Termination is set correctly. Make sure the last peripheral on the  
SCSI bus has termination. See the peripheral manual for proper termination  
information.  
After the above steps are executed, if you are still not recognizing all attached  
peripherals, configure the host adapter to operate in an Asynchronous Transfer  
mode by changing its setting under the SCSI Devices Setup section of the  
SmartSCSI Setup Utility. This feature is discussed thoroughly in the chapter entitled  
Host Adapter Setup.  
Question: On boot-up I get a message “Missing Operating System”, displayed. The boot drive  
is greater than 1 gigabyte.  
Answer:  
Verify the “DOS SPACE> 1 GB” is enabled in the INI-9XXX SmartSCSI Setup Utility.  
Question: Under SCO UnixWare, the system displays a panic message or crashes during  
bootup:  
Answer:  
Reboot the system and verify that the INI-9100A is using IRQ10. Please Refer to  
your system documentation to set the interrupt levels and your peripheral docu-  
mentation for help in setting SCSI ID’s.  
In order to boot from the old UnixWare kernel, reboot the system and execute the  
following steps:  
• Begin an interactive boot session by pressing the <SPACEBAR> at the  
BOOTING UNIXWARE prompt.  
• At the system [boot]# prompt, type KERNEL=unix.org <ENTER>  
• Type go <ENTER>.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
52  
Troubleshooting  
Consult the SCO UnixWare Installation Handbook “Troubleshooting” section to help  
isolate the problem. If it becomes necessary to remove the Initio device driver,  
please consult the “Removing the Initio Driver from a SCO UnixWare System”  
section of this document.  
B: DOS Space > 1GB  
The default disk head mapping for Initio SCSI host adapter is 255 heads and 63 sectors.  
This translates to a maximum accessible capacity of 8 GBytes per drive under MS-DOS.  
Warning: If you have already installed the operating system on your hard drives,  
changing the head mapping will corrupt your files and cause other unexpected prob-  
lems. Before changing any “DOS Space > 1GB” option setting, please back up your disk  
drives. Then you should run the FDISK utility to delete all the partitions on your selected  
disk drive. At this point you can switch the setting, reinstall the operating system, and  
restore your backed up files.  
All device drivers for the INI-9100A Host Adapter will support different head mappings  
based on the setting of “DOS Space > 1GB” option.  
MS-DOS, OS/2 & Windows NT  
Under MS-DOS, OS/2 & Windows NT, we recommend you enable “DOS Space > 1GB”  
option if your SCSI hard disk has more than 1 GByte capacity.  
SCO UNIX  
SCO UNIX does not have a 1 GByte barrier. Therefore, the “DOS Space > 1GB” option is  
not required to be enabled; however, you must make sure the root file system is located  
below 1024 cylinders in order to perform the kernel boot routines. If the size of the root  
file system is greater than 1 GByte or the location of root file system is beyond 1 GByte,  
you should enable the “DOS Space > 1GB” option.  
SCO UNIX can not support different head mappings for each disk drive under the same  
host adapter. The head mapping will be based on the setting represented by target ID 0.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
53  
Troubleshooting  
Drives with Multiple Operating Systems  
It is mandatory that the same head mapping be used across multiple operating systems  
on one drive. However you can use different head mappings on different drives with the  
exception of SCO UNIX. It is recommended that you enable “DOS Space > 1GB” option  
if the capacity of your SCSI hard disk has more than 1 GByte.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
55  
Index  
A
I
ASPI 15, 16  
I910u 46  
ASPI CD-ROM Driver 17  
ASPI Disk Driver Command Line  
Options 19  
ASPI Manager 17  
ASPI910U 17  
i910u ihv hba 46  
INI9100.HAM 34  
ini910U.DSK 34  
INI910U.INF 21  
INI910U.MPD 21, 23, 27, 28  
INI910U.SYS 29  
Autoexec.bat 18  
INICD.SYS 17  
INICD001 18  
B
Inidisk.sys 19  
INIFDISK, ASPI Partition & Format  
Utility 20  
INIFDISK.EXE 20  
Integrated Scatter/Gather Engine 3  
IRQ 45  
BIOS 15  
bus 16  
C
CD-ROM 18  
CONFIG.SYS 16  
CONTROL PANEL 22, 24, 27, 31  
K
D
KRNL32.DLL 21  
DEVICE MANAGER 23, 24, 28  
DEVICEHIGH= command 19  
Disk Access 16  
L
Load (Pathname) ini910u 36  
DOS 15  
DOS 4.01 21  
M
DOS ASPI 16  
DOSSETUP 15  
DSK drivers 34, 35  
MO 19  
MS-DOS 16, 33  
MSCDEX.EXE 17  
F
N
File Manager 22  
NetWare 33, 34  
NEW HARDWARE FOUND 23  
Novell 33  
H
Novell NetWare 33, 34  
HAM driver 34, 35  
HAVE DISK... 24  
Host Adapter Driver 23  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
56  
O
OEMSETUP.INF 29  
OS/2 driver 37  
OSR2 21, 25, 26  
P
PCI SCSI BUS CONTROLLERS 23  
PCI-SCSI Bus Controller 22  
PROGRAM MANAGER 16  
R
README.TXT 16  
S
SCO UNIX 41  
SCO UNIXWARE 45  
SCO UnixWare 45  
SCSI CONTROLLER 23, 31  
SCSI CONTROLLERS 28  
SCSI IDs 45  
SETUP.EXE 22  
SYSTEM.INI 16  
T
TXTSETUP.OEM 29  
U
UnixWare 47  
UPDATE DRIVER 28  
W
Windows 3.x 25  
Windows 95B 25, 26  
WINDOWS NTWORKSTATION SETUP 30  
Windows NT 29  
Windows NT 4.0 29  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
57  
Product Warranty  
Initio Corporation warrants to the original purchaser that this product shall be free from defects in  
material and workmanship for a period of 5 years from the date of purchase. Should this product, in  
the judgment of Initio Corporation, prove to be defective, Initio Corporation will at its option repair  
or replace the product once it has been returned to Initio Corporation free of charge. Any replaced  
parts or products become the property of Initio Corporation. You may obtain warranty service by first  
getting authorization from Initio Corporation then returning this product with proof of delivery date,  
shipping charges prepaid, to Initio Corporation. This warranty does not apply to the software  
component of the product nor to any product which has been subjected to misuse, accident, abuse  
or use in a manner inconsistent with normal host adapter operations. The original purchaser must  
be registered with Initio Corporation (by mailing the Product Registration Card) to qualify for  
warranty coverage. This remedy is your exclusive remedy for breach of this warranty.  
INITIO DISCLAIMS ALL OTHER WARRANTIES EITHER EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MER-  
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. INITIO SHALL BE LIMITED TO THE WARRANTY PERIOD  
SPECIFIED ABOVE. ALL OTHER WARRANTIES ARE EXCLUDED. INITIO’S TOTAL LIABILITY HEREUNDER SHALL NOT  
EXCEED THE PRICE PAID FOR THE PRODUCT PURCHASED. IN NO EVENT SHALL INITIO BE LIABLE FOR ANY INDI-  
RECT, SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFOR-  
MANCE OF THE PRODUCT, EVEN IF INITIO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
FCC Compliance Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device  
may not cause harmful interference, and (2) this device must accept any interference received, including interference  
that may cause undesired operations.  
Class B Equipment  
Information to User  
This equipment has been tested and found to comply with the limits for a CLASS B digital device, pursuant to Part 15  
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-  
dential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions contained in this manual, may cause harmful interference to radio commu-  
nications. However, there is no guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the  
following measures:  
Re-orient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that of the receiver.  
Consult the dealer or a experienced audio television technician.  
Note: Connecting this device to peripheral devices that do not comply with CLASS B requirements or using an unshielded  
peripheral data cable could also result in harmful interference to radio or television reception.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  
58  
Product Warranty  
The user is cautioned that any changes or modifications not expressly approved by the party responsible for  
compliance could void the user’s authority to operate this equipment.  
To ensure the use of this product does not contribute to interference, it is necessary to use shielded I/O Cables.  
Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the Federal  
Register, National Archives and Records Administration, U.S. Government Printing Office.  
Declaration of the Manufacturer/Importer  
We hereby certify that the I/OHIGHWAY PCI-FastSCSI Bus Master Host Adapters, in compliance with the require-  
ments of BMPT Vfg 243/1991, is RFI suppressed. The normal operation of some equipment (e.g., signal genera-  
tors) may be subject to specific restrictions. Please observe the notices in the user’s manual.  
The marketing and sale of the equipment was reported to the Federal Office for Telecommunication Permits  
(BZT). The right to retest this equipment to verify compliance with the regulation was given to the ZZF.  
EN 55 9100UW2 Declaration of Conformance  
This is to certify that the I/OHIGHWAY PCI–FastSCSI Bus Master Host Adapter is shielded against the generation  
of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity  
is declared by the application of EN 55 9100UW2:1987 Class B (CISPR 22:1985/BS 6527:1988).  
EN50081-1 GENERIC EMISSIONS STANDARD  
EN50082-1 GENERIC IMMUNITY STANDARD  
1. IEC 801-2 :1984(1000-4-2:1995);  
2. IEC 801-3 :1984(1000-4-3:1995);  
3. IEC 801-4 :1988(1000-4-4:1995).  
Production Notes  
®
™
This Initio User’s Manual was written, edited, and produced electronically using Adobe Pagemaker ,  
®
™
™
™
™
Adobe Photoshop , Macromedia Freehand , Adobe Streamline , and Microsoft Word .  
Text type is ITC Novarese® and display type is Universe 55®. ©1992 International Typeface Corpora-  
tion. ©1993 Linotype-Hell AG Corporation. All rights reserved.  
All product names that appear in this manual are for identification purposes only and are acknowl-  
edged to be trademarks or registered trademarks of their respective companies.  
®
initio  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ingersoll Rand Septic System 662400 C User Manual
Insignia Oven NS B2110 User Manual
Intel Computer Accessories 05 2342 002 User Manual
Intel Computer Hardware SE7320VP2 User Manual
Intel Universal Remote 05 2352 005 User Manual
Jeep Motorized Toy Car N9356 User Manual
Jet Tools Sander JDS 12B User Manual
Kathrein TV Cables EVK 14 User Manual
Kawasaki Motorcycle KX65 User Manual
KitchenAid Blender KSB550 User Manual