OWNER'S MANUAL
JDS-12B Benchtop 12” Disc Sander
(708432K shown with optional stand 708438 and Canister Filter 708434)
JET
P.O. BOX 1349
Auburn, WA 98071-1349
e-mail [email protected]
Phone: 253-351-6000
Fax: 1-800-274-6840
M-708433 05/02
WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Wear eye protection.
Always keep guards in place and in proper operating condition. Do not operate the machine
without the guards for any reason.
This disc sander is intended to be used with wood and wood products only. Use of this disc
sander and a dust collector with metal products is a potential fire hazard.
Support the workpiece adequately at all times during operation; maintain control of the work at
all times.
This disc sander is designed and intended for use by properly trained and experienced
personnel only. If you are not familiar with the proper and safe operation of a disc sander, do
not use until proper training and knowledge has been obtained.
•
REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and
adjusting wrenches are removed from the machine before turning it on.
•
•
KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.
DON’T USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.
•
•
•
KEEP CHILDREN AWAY. All visitors should be kept a safe distance from the work area.
MAKE THE WORKSHOP KIDPROOF with padlocks, master swatches, or by removing starter keys.
DON’T FORCE THE MACHINE. It will do the job better and safer at the rate for which it was
designed.
•
•
USE THE RIGHT TOOL. Don’t force a machine or attachment to do a job for which it was not
designed.
USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your machine
will draw. An undersized cord will cause a drop in the line voltage resulting in power loss and
overheating. The table following shows the correct size to use depending on the cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. Remember, the smaller the
gauge number, the heavier the cord.
Volts
120V
Total Length of Cord in Feet
25
16
50
AWG
16
100
14
150
12
•
•
WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
ALWAYS USE SAFETY GLASSES. Also use face or dust masks if the cutting operation is dusty.
Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.
•
•
DON’T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING.
REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position
before plugging in.
•
USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not
recommended by JET may cause hazards or risk of injury to persons.
•
•
NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped.
CHECK DAMAGED PARTS. Before further use of the machine, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform its
intended function - check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
•
•
NEVER LEAVE THE MACHINE RUNNING UNATTENDED. TURN POWER OFF. Don’t leave the
machine until it comes to a complete stop.
SOME DUST CREATED by power sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
•
•
•
Lead from lead based paint
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
•
Your risk from those exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specifically designed to filter out microscopic particles
•
•
DO NOT operate tool while under the influence of drugs, alcohol or any medication.
AVOID kickback by sanding in accordance with directional arrows. Sand on downward side of disc.
Sanding on the upward side could cause the workpiece to fly up causing injury.
•
•
•
•
SAND with the grain of the wood.
DO NOT sand pieces of material that are too small to be safely supported.
WHEN sanding a large workpiece, provide additional support at table height.
ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available
from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201, in the Accident
Prevention Manual for Industrial Operations and also in the safety Data Sheets provided by the NSC.
Please also refer to the American National Standards Institute ANSI 01.1 Safety Requirements for
Woodworking Machinery and the U.S. Department of Labor OSHA 1910.213 Regulations.
•
SAVE THESE INSTRUCTIONS refer to them often and use them to instruct others.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
Caution: This tool must be grounded while in use to protect the operator from electric shock.
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The
conductor, with insulation having an outer surface that is green with or without yellow stripes, is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is properly grounded. Use only three wire extension
cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug.
Repair or replace a damaged or worn cord immediately.
115 Volt Operation
As received from the factory, your sander is ready to run at 115 volt operation. This sander, when wired
for 115 volt, is intended for use on a circuit that has an outlet and a plug that looks like the one illustrated
in (A). A temporary adapter, which looks like the adapter as illustrated in (B), may be used to connect
this plug to a two-pole receptacle, as shown in (B) if a properly grounded outlet is not available. The
temporary adapter should only be used until a properly grounded outlet can be installed by a qualified
electrician. This adapter is not applicable in Canada. The green colored rigid ear, lug, or tab,
extending from the adapter, must be connected to a permanent ground such as a properly grounded
outlet box, as shown in (B).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
230 Volt Operation
If 230V, single phase operation is desired, the following instructions must be followed:
1. Disconnect the machine from the power source.
2. This JET sander is supplied with four motor leads that are connected for 115V operation, as shown in
Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B.
3. The 115V attachment plug (A), supplied with the sander, must be replaced with a UL/CSA listed plug
suitable for 230V operation (D). Contact your local Authorized JET Service Center or qualified
electrician for proper procedures to install the plug. The sander must comply with all local and
national codes after the 230 volt plug is installed.
4. The sander with a 230 volt plug should only be connected to an outlet having the same configuration
(D). No adapter is available or should be used with the 230 volt plug.
Important: In all cases (115 or 230 volts), make certain the receptacle in question is properly grounded.
If you are not sure, have a registered electrician check the receptacle.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
JDS-12B
Stock Number................................................................................................................................ 708433
Disc Diameter.......................................................................................................................................12”
Table Tilt ......................................................................................................................15° Up - 45° Down
Dust Chute Diameter ..............................................................................................................................4”
Disc Table .................................................................................................................16-3/8" W x 9-3/4” D
Motor..............................................................................................................1 HP, 115/230V, 60Hz, 1Ph
Impeller .................................................................................................................................9” x 1-13/16”
Overall Dimensions ...........................................................................................21” W x 25-5/8" D x 21” H
Net Weight (approx.) ....................................................................................................................100 Lbs.
Table of Contents
Warranty .................................................................................................................................................2
Warnings..............................................................................................................................................3-4
Grounding Instructions.............................................................................................................................5
115V Operation .......................................................................................................................................5
230V Operation .......................................................................................................................................6
Specifications..........................................................................................................................................7
Table of Contents ....................................................................................................................................7
Contents of the Shipping Carton..............................................................................................................8
Tools Required for Assembly & Adjustment .............................................................................................8
Unpacking ...............................................................................................................................................8
Stand Assembly (optional accessory).......................................................................................................9
Sander Assembly.....................................................................................................................................9
Table Adjustment...................................................................................................................................10
Sanding Disc Replacement....................................................................................................................10
Center Point ..........................................................................................................................................11
Brake.....................................................................................................................................................11
On/Off Switch........................................................................................................................................11
Lubrication.............................................................................................................................................11
Motor.....................................................................................................................................................11
Dust Collection ......................................................................................................................................11
Canister Filter (optional accessory)........................................................................................................12
Cleaning the filter ............................................................................................................................12
Optional Accessories.............................................................................................................................12
Troubleshooting.....................................................................................................................................13
Parts Breakdowns & Parts List..........................................................................................................14-17
Wiring Diagram .....................................................................................................................................18
The specifications in this manual are given as general information and are not binding. The WMH Tool
Group reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of the Shipping Carton
JDS-12B Benchtop Sander
1. Sander
1. Sanding Disc
1. Table
1. Miter Gauge
1. Inlet
1. Inlet Gasket
1. Owner's Manual
1. Warranty Card
Hardware Kit
4. Hex Head Bolt M10x40
8. Flat Washer M10
4. Lock Washers M10
4. Hex Nut M10
4. Hex Head Bolt M6x16
1. Center Point
1. Right Angle Hex Wrench 3mm
1. Filler Bar
1. Socket Head Cap Screw M5x8
OS-12DS Stand (optional accessory)
4. Stand Legs
4. Stand Supports
Hardware Kit
16. Carriage Bolt M8x16
16. Hex Nut M8
(708432K shown with optional stand 708438 and
Canister Filter 708434)
CF-12DS Canister Filter (optional accessory)
1. Canister Filter
1. Plastic Elbow
1. Grounding Wire
Tools Required for Assembly &
Adjustments
1. 13mm Wrench or socket
1. Combination Square
WARNING
Read and understand the entire contents of
this manual before attempting assembly or
operation of the disc sander!
Failure to comply may cause serious injury!
Unpacking
1. Remove all contents from the shipping
carton(s).
2. Report any damage to your distributor.
3. Do not discard any shipping material until
the sander has been assembled and is
running properly.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Stand Assembly (optional accessory)
1. Match the hole patterns in the stand legs
with the hole patterns in the stand supports.
Mount the legs to the outside of the supports
using sixteen M8x16 carriage bolts and
sixteen M8 flange lock nuts, figure 1. Do
not tighten until the stand has been
assembled and is sitting level on the floor.
2. Bolt the sander to the stand with four
M10x40 hex cap bolts, eight M10 flat
washers, four M10 lock washers and four
M10 hex nuts
Sander Assembly
1. Mount the sander to JET’s open stand with
four M10x40 hex head bolts, eight M10 flat
washers, four lock washers, and four hex
nuts. Tighten the nuts to secure the sander
to the stand.
Note: If you are going to use the sander as
a benchtop unit mount the sander to the
workbench with the supplied bolts.
2. Unscrew the knob (A, Fig. 2), remove the
washer (B, Fig. 2) and the trunnion holder
(C, Fig. 2). Repeat for opposite side.
3. Lift the table (D, Fig. 2) into position and set
on top of the split pins and threaded shaft.
4. Reinstall the trunnion holder, washer and
knob. Repeat for opposite side.
5. Make sure the trunnion and trunnion holder
engage and tighten the knob.
6. Place the gasket (E, Fig. 3) against the
sander base and mount the inlet port (F, Fig.
3) to the sander with four M6x16 hex cap
bolts (G, Fig. 3).
Warning
Avoid kickback by sanding in accordance
with directional arrow. Sand on downward
side of disc. Sanding on the upward side
could cause the workpiece to fly up causing
injury! Failure to comply may cause serious
injury!
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Adjustment
The table stops have been set-up at the factory.
However, if you run into a problem, or want to
check the table follow the below listed steps.
1. Loosen lock knobs (B, Fig. 4) and move the
table to the 90 degree position. Tighten
knobs and place a square (A, Fig. 4) against
the table and disc. The square should rest
flat against the table and disc.
2. If adjustment is needed move the table so
that it rests 90 degrees from the table, and
loosen the hex nut (D, Fig. 5) and tighten
the set screw (C, Fig. 5) until it contacts the
table surface. Tighten hex nuts. This will
properly adjust the 90-degree stop.
3. Loosen the lock knobs (F, Fig. 5) and tilt the
table up just enough to pivot the stop (E, Fig.
5) out of the way.
4. Tilt the table down until it hits the 45 degree
stop (G, Fig. 5). Tighten lock knobs, and
check the table with a combination square.
5. If adjustment is needed, loosen the hex nut
(H, Fig. 5) and adjust the socket head cap
screw (G, Fig. 5) until it contacts the table.
Tighten hex nuts.
6. Always maintain a gap of approximately
1/16” between the table edge, and disc. If
adjustment is necessary loosen hex cap
bolts (I, Fig. 5) and move the table into
position. Tighten hex cap bolts.
7. The table tilts between 15° up - 45° down by
loosening the lock knobs and tilting the table
to the desired angle. Tighten the knobs.
8. If you want to tilt the table up you need to
pivot the stop (E, Fig. 5) out of the way.
Sanding Disc Replacement
1. Disconnect machine from the power
source.
2. Remove the knobs (J, Fig. 6), washers (K,
Fig. 6), and trunnion holders (L, Fig. 6)
followed by the table assembly (M, Fig. 6).
3. Remove old sanding disc by striping from
wheel. Use a cleaner and putty knife to
remove the residue. Make sure the disc
plate is clean and dry.
4. Press the new disc firmly into place.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
If you want to run the JDS-12B on 230V refer to
the wiring diagram found on the inside of the
switch box cover (F, Fig. 8).
Center Point
The center point (A, Fig. 7) provided with the
sander can be used for sanding circles. Slide
the center point into the miter slot that is
perpendicular to the sanding disc. The radius of
the desired circle should be the distance from
the center point to the sanding disc. Lock the
center point in position by tightening the set
screws. Cut the wood to the approximate
diameter and press on to the center point.
Rotate the wood until the desired results are
achieved.
Before hooking up to the power source, make
sure that the switch is in the off position.
Dust Collection
The disc sander has a built in fan designed to
suck the saw dust away from the sanding disc
and exhaust through the inlet (C, Fig. 7). For
best results hook the sander to JET’s optional
accessory canister filter (#708434).
Filler Bar
The sander can also be attached to a dust
collector using a 4” diameter hose and clamp.
JET offers a wide variety of hoses, adapters and
dust collectors.
The filler bar (H, Fig. 7) should be added when
sanding small workpieces. Secure in place with
the socket head cap screw (I, Fig. 7). When not
using the filler bar thread the socket head cap
screw (I, Fig. 7) in the tapped hole as a stop.
Brake
After you have turned the sander “OFF” you can
press the brake (B, Fig. 7) to slow, or stop the
sanding disc.
On/Off Switch
The machine can be turned “ON” by moving the
switch (D, Fig. 8) to the “UP” position. The key
(E, Fig. 8) can be removed when the machine is
in the “OFF” position. With the key removed
the switch will not operate.
Lubrication
You may need to lubricate the trunnion, and
trunnion holder (G, Fig. 8) if the table does not
tilt smoothly.
Motor
Make frequent inspections of the motor fan cover,
and blow out (with low pressure air hose) or
vacuum any accumulation of foreign material in
order to maintain normal motor ventilation.
WARNING
All electrical connections must be done by
a qualified electrician. All adjustments or
repairs must be done with the sander
disconnected from the power source,
unplugged. Failure to comply may result in
serious injury!
The JDS-12B disc sander is rated 115V/230V,
Prewired 115V.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Filter (optional accessory)
1. Remove the inlet port that came with the
sander.
2. Mount the plastic elbow (A, Fig. 9) to the
sander using the same hardware (B, Fig. 9)
from the inlet port.
3. Connect the filter (C, Fig. 9) to the elbow
and turn counter-clockwise so that it locks in
place.
WARNING
Static electricity will build up in the filter
during operation. The filter ground must be
attached to the machine ground, and to the
filter. Failure to comply may result in
fire/loss of property, or personal injury!
4. Remove the screw (D, Fig. 9) from the
sander base.
Attach the end of the
grounding wire to the screw and thread back
in to the base.
5. Attach the grounding clip (E, Fig. 9) to the
metal part of the filter. This will prevent
static electricity from building up in the filter.
Cleaning the Filter
CAUTION
Wearing a particle mask/respirator for
protection against fine dust particles during
cleaning is highly recommended.
Optional Accessories
708438: Open Stand
708434: Canister Filter
57620025: JET Stik Abrasive Belt and Disc
Cleaner.
Clean the canister filter frequently to keep the
sander’s performance at its optimum. To clean:
Dust Collectors and Accessories see a JET
Distributor.
JDS-12B Sanding Disc PSA Aluminum Oxide
“J” Weight Cloth Back.
1. Disconnect the machine from the power
source.
2. Take off the grounding clip and remove the
filter (C, Fig. 9) by turning clockwise.
12”
36 Grit
50 Grit
60 Grit
Stock
Number
Master
Carton
12”
Stock
Number
Master
Carton
3. Empty the contents into an appropriate
container.
57698525
57698650 57698750
25
50
50
4. The filter can be cleaned with a low
pressure air hose. Blow from the outside of
the filter to clean the dust particles. For
best results check and empty the filter
frequently.
80 Grit
57698850
100 Grit
120 Grit
57698950 57699050
50 50
50
5. Install the filter and reattach the grounding
clip.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Possible Cause
Trouble
Solution
1. Sander unplugged from wall
or motor
1. Check all plug connections
2. Replace fuse or reset circuit
breaker
Sander will not start
2. Fuse blown or circuit breaker
tripped
3. Replace cord
3. Cord damaged
1. Replace with adequate size
and length cord
1. Extension cord too light or
too long
Sanding disc does not come
up to speed
2. Contact a qualified
electrician
2. Low current
1. Adjust stand or base so that
it rests evenly on the floor
1. Stand or base on uneven
surface
Machine vibrates excessively
Sanded edge not square
2. Bolt down
1. Table not square to sanding
disc
1. Use a square to adjust table
to sanding disc
1. Keep workpiece moving
1. Work held still
2. Use coarser grit for stock
removal and fine grit for
finish sanding.
2. Wrong grit sanding disc
3. Feed pressure too great
4. Sanding against the grain
Sanding marks on wood
3. Never force workpiece
4. Sand with the grain
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Sander Breakdown
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List For The JDS-12B Benchtop Disc Sander
Disc Sander
Index Part
No. No.
Description
Size
Qty
1..........612131......................... Guard Base ........................................... ...............................................1
2..........MH612001 ................... Motor.....................................................1 HP, 1Ph 110V/220V .............1
............JDS12B-MFC............... Motor Fan Cover (not shown) ................ ...............................................1
............JDS12B-MF ................. Motor Fan (not shown)........................... ...............................................1
............JDS12B-CS.................. Centrifugal Switch (not shown)............... ...............................................1
............JDS12B-CC ................. Capacitor Cover (not shown) ................. ...............................................1
............JDS12B-JBC................ Junction Box Cover (not shown) ............ ...............................................1
............JDS12B-SC.................. Starting Capacitor (not shown)...............200MFD, 125VAC.....................
............JDS12B-RC ................. Running Capacitor (not shown)..............10uF, 250V ...............................
3..........KS050565 .................... Key........................................................5x5x65....................................1
4..........994534......................... On/Off Switch........................................ ...............................................1
5..........998621......................... Strain Relief........................................... ...............................................1
6..........IC100001 ..................... Power Cord............................................ ...............................................1
7..........TS-1551071 ................. Spring Washer.......................................M8 ..........................................4
8..........SJ080400..................... Pan Head Socket Bolt............................M8x20.....................................4
9..........612132......................... Fan Blade..............................................9” ............................................1
10........612133......................... Partition................................................. ...............................................1
11........SF069200 .................... Pan Head Bolt w/Flange ........................M6x8.......................................5
12........612134......................... Sanding Disc ......................................... ...............................................1
13........SS060200 .................... Set Screw..............................................M6x8.......................................1
14........612113......................... Washer.................................................. ...............................................1
15........SM089400.................... Countersunk Head Bolt..........................M8x16.....................................1
16........57698525..................... 12” Disc Sanding Paper 36 Grit ............. .............................................25
............57698650..................... 12” Disc Sanding Paper 50 Grit ............. .............................................50
............57698750..................... 12” Disc Sanding Paper 60 Grit ............. .............................................50
............57698850..................... 12” Disc Sanding Paper 80 Grit ............. .............................................50
............57698950..................... 12” Disc Sanding Paper 100 Grit............ .............................................50
............57699050..................... 12” Disc Sanding Paper 120 Grit............ .............................................50
17........612136......................... Front Cover ........................................... ...............................................1
18........SF069200 .................... Pan Head Bolt w/Flange ........................M6x8.......................................5
19........TS-1504071 ................. Socket Head Cap Screw........................M8x35.....................................1
20........TS-1540061 ................. Hex Nut .................................................M8 ..........................................1
21........TS-1550061 ................. Flat Washer...........................................M8x18.....................................1
22........612038......................... Trunnion Holder (A) ............................... ...............................................1
23........PS062600 .................... Spring Pin..............................................6x26........................................4
24........SS081200 .................... Set Screw..............................................M8x60.....................................2
25........TS-1550061 ................. Flat Washer...........................................M8x18.....................................2
26........612098......................... Knob......................................................M8 ..........................................2
27........612052......................... Trunnion Holder (B) ............................... ...............................................1
28........612135......................... Table..................................................... ...............................................1
29........612046......................... Trunnion................................................ ...............................................2
30........TS-1551061 ................. Lock Washer .........................................M8 ..........................................4
31........TS-1490021 ................. Hex Head Bolt .......................................M8x16.....................................4
32........612010......................... Locating Block....................................... ...............................................1
33........PS053600 .................... Spring Pin..............................................5x36........................................1
34........TS-1540041 ................. Hex Nut .................................................M6 ..........................................1
35........TS-1523071 ................. Set Screw..............................................M6x25.....................................1
36........612116......................... Brake..................................................... ...............................................1
37........612118......................... Brake Fixed Base .................................. ...............................................1
38........PS042600 .................... Spring Pin..............................................4x26........................................1
39........SP040200 .................... Pan Head Bolt .......................................M4x10.....................................3
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Index Part
No. No.
Description
Size
Qty
40........612140......................... Spring.................................................... ...............................................1
41........WF051210 ................... Flat Washer...........................................M5x12.....................................1
42........612115......................... Stop Handle........................................... ...............................................1
43........TS-1491061 ................. Hex Head Bolt .......................................M10x40...................................4
44........TS-1550071 ................. Flat Washer...........................................M10x20...................................8
45........TS-1551071 ................. Lock Washer .........................................M10.........................................4
46........TS-1540072 ................. Hex Nut .................................................M10.........................................4
47........612137......................... Packing ................................................. ...............................................1
48........612145......................... Inlet .......................................................4” ............................................1
49........TS-1482031 ................. Hex Head Bolt .......................................M6x16.....................................4
50........612099......................... Sponge.................................................. ...............................................1
51........TS-1551021 ................. Lock Washer .........................................M4 ..........................................2
52........AB198101 .................... Miter Gauge Assembly .......................... ...............................................1
53........AB612143 .................... Circle Gauge Assembly (ASM) .............. ...............................................1
57........612117......................... Sponge Gasket...................................... ...............................................1
58........SP059200 .................... Pan Head Bolt .......................................M5x8.......................................1
59........WE050000................... Star Washer ..........................................M5 ..........................................1
60........612171......................... Filler Bar................................................ ...............................................1
61........TS-1502011 ................. Socket Head Cap Screw........................M5x8.......................................1
* ..........JDS12B-HK.................. Hardware Kit (not shown)....................... .................................................
............JDS12B-WL................. Warning Label (not shown) .................... .................................................
............JDS12B-ID................... I.D. Label (not shown)............................ .................................................
............JDS12B-JL................... JET Label (not shown)........................... .................................................
Optional Accessory
54........612147......................... Elbow .................................................... ...............................................1
55........331022......................... Filter...................................................... ...............................................1
56........331033......................... Grounding Clip ...................................... ...............................................1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Open Stand Breakdown (optional accessory)
JDS-12B Stand Assembly (optional accessory)
Description
Index Part
No. No.
Size
Qty.
1..........612141............................. Stand Leg...................................................... ...................................4
2..........612142............................. Stand Support ............................................... ...................................4
3..........SC089400........................ Carriage Bolt ................................................. M8x16 ......................16
4..........NF081300 ........................ Flange Lock Nut ............................................ M8............................16
* ..........OS12DS-HK..................... Hardware Kit (not shown)............................... .....................................
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|