Ten.dvc 10" S u b w o o f e r
BETA TEN.DVC 2-OHM (PARALLEL) WIRING
BETA TEN.DVC DUAL-SUBWOOFER WIRING
(Dual) Beta Ten.dvc
Beta Ten.dvc
(rear view)
(rear view)
I N S T R U C T I O N S
CAR AUDIO
+
+
+
–
+
–
+
–
+
+
–
Thank you for purchasing an Infinity Beta Ten.dvc
10" Dual Voice-Coil Subwoofer. You’ve selected a
premium product that offers superior performance
and advanced materials, resulting from over 25
years of loudspeaker design. This Infinity product is
made with our ongoing dedication to create the best
consumer audio products possible. As a result, you
can expect your new Beta Subwoofer to provide you
with many years of listening enjoyment.
• Locate and note all fuel lines, hydraulic brake
lines, and electrical wiring. Use extreme caution
when cutting or drilling in and around these areas.
From
Amp
Output
®
®
®
From
Amp
Output
–
–
• Check clearances on both sides of a planned
mounting surface before drilling any holes or
installing any screws.
METHOD #1
+
–
–
THIELE-SMALL PARAMETERS
Refer to Subwoofer Enclosure Trade-Offs (on the
inside pages) for help in selecting an enclosure type
and alignment. Also, review the wiring diagrams (on
the back page) on how to connect the subwoofer for
2-ohm, 8-ohm, and summed-mono applications.
FREE-AIR RESONANCE:
FS (HZ
)
3
24.00
2.70
77.00
8.08
0.20
0.20
0.39
10.00
2.80
(Dual) Beta Ten.dvc
(rear view)
COMPLIANCE VOLUME:
VAS (FT
)
VAS (LITERS)
QMS
+
–
+
–
+
–
–
+
BETA TEN.DVC 8-OHM (SERIES) WIRING
From
Amp
Output
MECHANICAL Q:
ELECTRICAL Q:
TOTAL Q:
®
®
Each Infinity Beta Ten.dvc 10" Dual Voice-Coil
Subwoofer is covered by our limited parts and labor
warranty (see the enclosed warranty card). Keep
your original dated bill of sale in case warranty ser-
vice is required.
Beta Ten.dvc
QES
(rear view)
+
–
QTS
+
MAXIMUM EXCURSION:
XMAX (IN)
XMAX (MM)
RE (OHMS)
+
–
METHOD #2
®
From
Amp
Output
IMPORTANT: Installation of automotive stereo
components can require extensive experience in
dealing with a variety of electrical, and
mechanical procedures, including subwoofer
box building. Although these instructions
explain how to install a Beta Subwoofer in a
general sense, they do not show the exact instal-
lation methods for your particular vehicle. If
you do not have the experience, do not attempt
the installation yourself; instead ask your
Authorized Infinity Car Audio Dealer about
professional installation options.
VOICE COIL
DC
RESISTANCE:
IMPORTANT: When connecting two Beta
Ten.dvc subwoofers together, use Method #1 to
create a net 4-ohm impedance. NEVER USE
METHOD #2, since most amplifiers cannot fully
control driver movement in this configuration.
SPECIFICATIONS
DIAMETER:
+
–
–
10" (254.0 MM)
SENSITIVITY (2.83 V @ 1M): 93 dB
POWER HANDLING:
FREQUENCY RESPONSE:
NOMINAL IMPEDANCE:
DIMENSIONS:
250 WRMS PER VOICE COIL
20 ~ 500 HZ
BETA TEN.DVC SUMMED-MONO WIRING
4
OHMS PER VOICE COIL
Beta Ten.dvc
(rear view)
DECLARATION OF CONFORMITY
mounting depth
4.75" (120.65 mm)
PRECAUTIONS
+
–
We, Infinity Systems A/S
Kongevejen 194B
DK-3460 Birkerød
DENMARK
• Always wear protective eyewear when using tools.
From
Left
From
Right
Amp
declare in own responsibility, that the Beta Ten.dvc subwoofer
is in compliance with technical standards
• Turn off all audio systems and other electrical
devices before starting the installation.
Amp
cutout diameter
9.37" (238.00 mm)
EN 50 081-1/1992 and EN 50 082-1/3.1995
Output
Output
• Disconnect the (–) negative lead from your vehi-
cle’s battery.
+
–
outer diameter
10.70" (271.78 mm)
Steen Michaelsen
Infinity Systems A/S
Birkerød. DENMARK. 4/96
Infinity Systems, Inc.
Chatsworth, CA 91311, USA
20630 Nordhoff Street
Infinity Systems, Inc.
Chatsworth, CA 91311, USA
20630 Nordhoff Street
•
•
VOICE (818) 407-0228 • FAX (818) 709-9486
VOICE (818) 407-0228 • FAX (818) 709-9486
•
•
®
®
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed In Japan
|