59CL-4 & 59CLF-4
UNDERMOUNT
MOWER
Tested. Proven. Unbeatable.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
OPERATION & SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DEALER CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 23
PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . INSIDE BACK COVER
GENERAL INFORMATION
The purpose of this manual is to assist you in operating
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.
and maintaining your mower. Read it carefully. It fur-
nishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature due to unknown and varying
operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.
■
Some illustrations in this manual show the
mower with safety shields removed to provide a
better view. The mower should never be operated
without necessary safety shielding.
The illustrations and data used in this manual were cur-
rent at the time of printing but, due to possible inline
!
LEA EL INSTRUCTIVO!
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
29929 (Rev. 3/28/2008)
Introduction 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
„ Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
„
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
In addition to the design and configuration of
equipment, hazard control and accident preven-
tion are dependent upon the awareness, con-
cern, judgement, and proper training of
personnel involved in the operation, transport,
maintenance, and storage of equipment.
„ Inspect and clear area of stones, branches, or
other hard objects that might be thrown, causing
injury or damage.
OPERATION
„ You may not be able to stop the tractor safely if
the clutch or brake pedal mechanisms are improp-
erly adjusted, allowing them to contact mower
components.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be
that kind of operator.
„ When the mower lift stops are installed as
instructed in this manual, properly adjusted clutch
and brake pedal mechanisms will not contact
mower components. You should frequently check
that the tractor clutch and brake pedal mechanisms
are in adjustment.
TRAINING
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ If the clutch or brake pedal mechanisms can
contact mower components, do not put mower into
service until properly adjusted.
„ Do not put mower into service unless discharge
chute is installed and in good condition. Replace if
damaged.
„ If you do not understand any part of this manual
and need assistance, see your dealer.
„ Keep bystanders away from equipment.
„ Know your controls and how to stop engine and
attachment quickly in an emergency.
„ Do not operate or transport equipment while
under the influence of alcohol or drugs.
„
Operators must be instructed in and be capable
„ Never direct discharge toward people, animals,
or property.
of the safe operation of the equipment, its attach-
ments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
„ Operate only in daylight or good artificial light.
„ Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
„ Never allow children or untrained persons to
operate equipment.
PREPARATION
„ Always comply with all state and local lighting
and marking requirements.
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
„ Never allow riders on power unit or attachment.
„ Always sit in power unit seat when operating
controls or starting engine. Place transmission in
neutral, engage brake, and ensure all other con-
trols are disengaged before starting power unit
engine.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Look down and to the rear and make sure area
is clear before operating in reverse.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
„ Do not operate or transport on steep slopes.
„ Remove accumulated debris from this equip-
„ Do not stop, start, or change directions sud-
ment, power unit, and engine to avoid fire hazard.
denly on slopes.
59CL Safety Rules (Rev. 10/12/2007)
4 Safety
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
„ Use extreme care and reduce ground speed on
slopes and rough terrain.
system leak down, hydraulic system failures,
mechanical failures, or movement of control levers
can cause equipment to drop or rotate unexpect-
edly and cause severe injury or death. Follow Oper-
ator's Manual instructions for working underneath
and blocking requirements or have work done by a
qualified dealer.
„ Watch for hidden hazards on the terrain during
operation.
„ Stop power unit and equipment immediately
upon striking an obstruction. Turn off engine,
remove key, inspect, and repair any damage before
resuming operation.
„ Make sure attachment is properly secured,
adjusted, and in good operating condition.
TRANSPORTATION
„ Always comply with all state and local lighting
and marking requirements.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
„ Never allow riders on power unit or attachment.
„ Do not operate PTO during transport.
„
Make certain all movement of equipment com-
ponents has stopped before approaching for ser-
vice.
„ Watch for hidden hazards on the terrain.
„ Do not operate or transport on steep slopes.
„ Frequently check blades. They should be sharp,
„ Do not operate auxiliary hydraulics during
free of nicks and cracks, and securely fastened.
transport.
„ Do not handle blades with bare hands. Careless
or improper handling may result in serious injury.
„ Do not operate or transport equipment while
under the influence of alcohol or drugs.
„ Your dealer can supply genuine replacement
blades. Substitute blades may not meet original
equipment specifications and may be dangerous.
MAINTENANCE
„ Before dismounting power unit or performing
any service or maintenance, follow these steps:
disengage power to equipment, lower the 3-point
hitch and all raised components to the ground,
operate valve levers to release any hydraulic pres-
sure, set parking brake, stop engine, remove key,
and unfasten seat belt.
„ Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
„ Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
„ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
„
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Wear gloves when installing belt. Be careful to
prevent fingers from being caught between belt
and pulley.
STORAGE
„ Never go underneath equipment (lowered to the
ground or raised) unless it is properly blocked and
secured. Never place any part of the body under-
neath equipment or between moveable parts even
when the engine has been turned off. Hydraulic
„ Block equipment securely for storage.
„ Keep children and bystanders away from stor-
age area.
™
59CL Safety Rules (Rev. 10/12/2007)
Safety 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
1 - PN 19007
3 - SERIAL NUMBER PLATE
MODEL NO.
SERIAL NO.
2 - PN 53425
Woods Equipment Company
Oregon, Illinois, U.S.A.
DANGER
BE CAREFUL!
Use a clean, damp cloth to clean safety
decals.
ROTATING BLADES AND
THROWN OBJECTS
Avoid spraying too close to decals when using
a pressure washer; high-pressure water can
enter through very small scratches or under
edges of decals causing them to peel or come
off.
ꢀDo not put hands or feet under or into mower when
engine is running.
ꢀBefore mowing, clear area of objects that may be
thrown by blade.
ꢀKeep bystanders away.
ꢀKeep discharge chute and guards in place and in good
condition.
Replacement safety decals can be ordered
free from your Woods dealer. To locate your
nearest dealer, check the Dealer Locator at
States and Canada call 1-800-319-6637.
BLADE CONTACT OR THROWN OBJECTS CAN
CAUSE SERIOUS INJURY OR DEATH.
53425-B
29929 (Rev. 3/28/2008)
6 Safety
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
4 - PN 18877
5 - PN 18868
DANGER
WARNING
TO AVOID SERIOUS
INJURY OR DEATH:
SHIELD MISSING
Do not operate.
Put shield on.
18868-B
ꢀ
ꢀ
Read Operator's Manual (available
from dealer) and follow all safety
precautions.
Keep all shields in place and in good
condition.
6 - PN 18869
DANGER
SHIELD MISSING
ꢀ Operate mower from tractor seat only.
ꢀ Lower mower, stop engine and remove
key before dismounting tractor.
DO NOT OPERATE - PUT SHIELD ON
ꢀ Allow no children or untrained persons
to operate equipment.
ꢀ Do not transport towed or
semi-mounted units over 20 mph.
FAILURE TO OPERATE SAFELY
CAN RESULT IN
INJURY OR DEATH.
18877-C
7 - PN 23376
29929 (Rev. 3/28/2008)
Safety 7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION & SERVICE
necessary to make the belt run true. The side adjust-
MOWING GRASS
ment holes are also for additional belt takeup in case
belt adjustment is used on the idlers. It is very impor-
tant to run the belt as much in line as possible at all
times.
Woods mowers are equipped with suction-type blades
which make them ideal for finish mowing large areas of
lawn.
The machine should be run level when mowing, and
the uncut area kept to the left side (right side on left-
hand machine) to prevent small windrow that might
otherwise occur.
Lubrication
Lubricate the blade spindle shafts with SAE 80 or 90EP
gear lube every 24 hours of operation until some oil is
forced out around the top of the shaft. If machine is
equipped with casters, grease occasionally to keep the
powdered metal bearing well lubricated. The V-belt
idlers have sealed ball bearings and do not need lubri-
cating. On mowers using chain drive and jackshaft,
keep chain well oiled and grease jackshaft every 24
hours of operation.
Streaking
With certain types of grass and under certain seasonal
conditions, the front caster wheels may roll the grass
down enough that it will not come all the way back up
and will not be cut as short as the surrounding area.
This may appear to be a streak left by the spindle, but it
is not. The only solution, under these conditions, is to
carry the weight of the machine on the lift chains with
the caster wheels adjusted up so they carry the weight
when riding a high ridge or high spot.
V-Belts
Belts should be adjusted so that they are tight enough
to hold the power of the tractor when mowing. The
mowers for IH Cub tractors are designed so that as the
mower is raised above the mowing position, the belt
slackens. This is to prevent excessive load on the trac-
tor PTO pilot bearing when the tractor motor is oper-
ated with PTO disengaged. Thus, on Cubs, the
operator should avoid adjusting the drive belt so tight
that the slackening off effect is eliminated. On other
tractors, to prevent belt from jumping off, the belt
should be adjusted so it is snug and not tight when
mower is raised.
TRACTOR OPERATING INSTRUCTIONS
Operate the tractor at full governed rpm when doing
normal mowing. If the forward speed is too high, a
lower gear can be used.
Height Adjustment (Without Casters)
The mower is raised, lowered and mowing height main-
tained by the tractor hydraulic system. Set the hydrau-
lic control lever stop for the mowing level desired; then
adjust the side skids so that they just clear the ground.
The side skids will then minimize scalping by lifting the
mower over bumps.
When belt replacement is necessary, use only belts
recommended by Woods dealers. These are of special
construction for shock loading and severe use.
Side Shield & Discharge Chute
Height Adjustment (With Casters)
Both a side shield and a discharge chute are provided
for the discharge end of mower (left end on white
mower frames and right end of yellow frames). The
side cover shield should be used in light mowing and
when mowing in areas where other persons may be
present. The discharge chute is used in heavy mowing
to allow easier escape of cut material. Always use
either side shield or discharge chute.
The mower may be raised off the casters at any time by
the tractor lift system, but regulate mowing height with
caster height. Adjust mowing height by transferring
spacers from below the caster mounting bracket to
above it or vice versa and by moving wheel up or down
in holes in wheel yoke.
Attitude Adjustment
OPTIONAL EQUIPMENT
The rotary mower can be adjusted to ride level at vari-
ous cutting heights by adjusting the rear of the machine
up or down in the mounting bracket holes. After chang-
ing the height of the rear of the mower, always check
the alignment of the belt from the idlers forward. If the
belt is out of line, move the entire mower forward or
back in the side adjustment holes or adjust idlers as
Two caster wheels are available for mounting on the
front of the mower. This will gage the mowing height
very accurately. The leaf mulcher disposes of leaves
quickly and economically. It returns valuable organic
material to the soil.
8 Operation
29929 (Rev. 3/28/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
MOWER SPINDLE ASSEMBLIES
CLEANING
Mower spindles are equipped with two tapered roller
bearings. The proper adjustment is held by a spring
pin. It is not intended that these bearings be adjusted
during their useful life. When difficulty is experienced
with the mower spindle assembly, time and trouble will
be saved by buying a completely new spindle assem-
bly.
After Each Use
●
●
●
Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
Inspect machine and replace worn or damaged
parts.
Replace any safety decals that are missing or not
readable.
However, if bearings must be adjusted, the spring pin
can be driven out, the sleeve pulled loose, and a
washer shim placed under the sleeve to tighten the
bearings.
Periodically or Before Extended Storage
●
Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
●
Remove the remainder using a low-pressure water
spray.
SERVICING CUTTING BLADES
Blades are made of heat-treated alloy steel and are
designed to produce the most satisfactory results. For
a good mowing job, always keep blades sharp.
1. Be careful when spraying near scratched or torn
safety decals or near edges of decals as water
spray can peel decal off surface.
NOTE: On left hand models (L - White Frame) the
blade bolts have left-hand threads.
2. Be careful when spraying near chipped or
scratched paint as water spray can lift paint.
3. If a pressure washer is used, follow the advice
MODEL 59 MOWER
of the pressure washer manufacturer.
●
●
Inspect machine and replace worn or damaged
parts.
This mower does not have friction blade clutch. The
bolt which is used to fasten the blade to the mower
spindle shaft has a nylon insert to prevent it from black-
ing out too easily. Do not substitute an ordinary bolt.
When replacing the blade, tighten the bolt tight enough
so that the blade will not slip.
Sand down scratches and the edges of areas of
missing paint and coat with Woods spray paint of
matching color (purchase from your Woods
dealer).
●
Replace any safety decals that are missing or not
readable (supplied free by your Woods dealer).
See Safety Decals section for location drawing.
Operation 9
29929 (Rev. 3/28/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly of this mower is the responsibility of the
Woods dealer. It should be delivered to the owner com-
pletely assembled, lubricated, and adjusted for normal
cutting conditions.
Refer to mower frame assembly illustrations and parts
list. Lay out parts and hardware on a clean surface to
aid in assembly.
AꢀꢀWARNING
■
Keep all persons away from the operator con-
trol area while performing adjustments, service or
maintenance.
Figure 1. Photo of Mounting Plate Supplied in 10570
AꢀꢀCAUTION
and Installation of Attachment Bracket
■
Always wear relatively tight and belted clothing
to avoid entanglement in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hands, hearing and head.
Side Shields (See page 16)
Attach side shields to the mower with 3/8 x 1" cap
screws and flange lock nuts. A side discharge chute
(60) may be installed on the right end of the mower in
place of side shield (54).
Center Belt Shield (See page 16)
Bolt center belt shield bracket (21) to mower deck in
hole just behind center spindle using 3/8 x 1" bolt, lock
washer and nut. Bolt center shield (22) to this bracket
and to deck, using the three bolts welded in them.
Secure with 3/8" nuts and lock washers.
Figure 2. 59CLF-4 with Fast Hitch Shown Mounted
on Cub Lo-Boy Tractor with all of the
Fast Hitch Equipment Installed
Remove the drawbar mounting plates for the Fast Hitch
from the Fast Hitch. Replace with special mounting
plates supplied in the kit.
Side Skids (See page 16)
Bolt the side skids on in such a position that they will be
carried close to the ground when the mower is oper-
ated at the desired mowing height. Use 3/8 x 1-1/4 heat
treated bolts (torque to 35 lbs-ft) lock washers and
nuts.
Front Toe Guards (See page 16)
Front toe guards (59) are furnished for some mowers.
When provided, bolt them to front of mower, using 3/8
NC x 3/4" carriage bolts and 3/8" flange lock nuts.
Attachment Arms
Fast Hitch
For tractors with fast hitch, see page 16. Bolt attach-
ment arms (31) and (40) to inside of drawbar mounting
brackets on the tractor with one 5/8 x 1-3/4" cap screw
and lock washer and one 1/2 x 2-1/2" cap screw, flat
washer, lock washer, and nut in each. If drawbar is not
used, place a 5/8 x 1-3/8 x 5/8" washer between verti-
To use 59CLF-4 with Fast Hitch, accessory kit 10570
must be used.
10 Assembly
29929 (Rev. 3/28/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
cal push arms (31 and 40) and attachment brackets
(32) and (39).
Belt Assembly & Adjustment
First put belt on bottom groove, right hand side of the
center sheave. Then thread it to the left, around the left
hand sheave.
Idler Bracket Assembly (See Figure 9 &
page 16)
Remove the cap screws from the PTO bearing plate.
Bolt the idler bracket assembly (36, 37, 38 and 45) to
the tractor using 3/8 x 1-1/2" cap screws and lock
washers.
Sheave for Belt Pulley Shaft (See page 16)
Remove paint from bore of sheave (41). Put 1" splined
tapered bushing in sheave (41) and insert screws to
hold bushing in place, but DO NOT TIGHTEN. Slide
sheave and bushing on PTO shaft and leave loose until
belts are put on and lined up. After proper alignment is
obtained, tighten bushing bolts evenly to 12 lbs-ft of
torque, alternating back and forth at least six times.
Mount Mower (See page 16)
Slide mower under tractor, attach crosswise rear sup-
port (35) to the two channel arms (33) using 5/8 x
1-1/2" clevis pins and safety pins (28).
Figure 3. Belt Installation
Channel Arms (See page 16)
Bring the belt back across the center sheave in the
center groove over to the right outside sheave.
Attach two channel arms (33) with single bore hole end
to the mower, using 5/8 x 1-1/2 clevis pins and safety
pins. Use upper hole in arms for high grass. Attach
channel arms to brackets (31 & 40) using 5/8 x 1-3/4
clevis pins.
Attach the crosswise rear support (35) to the mower
frame using one 1/2 x 2" cap screw, pivot bushing (34)
and flange lock nut.
Lifting Assembly (See page 16)
Attach the lift assembly to right hydraulic arm of the
tractor, using two 5/8 x 1-3/4 cap screws, lock washer
and nut.
Attach two 10-link lift chains (9) to the key holes in lift
lugs on mower frame and secure with plastic caplug.
Attach upper end of chains to the eye bolts of lift
assembly.
Raise the mower on the tractor hydraulic system
slightly and adjust the chain to carry the mower level.
Adjust stops on lift control lever so mower will not hit
tires or bottom of tractor when fully raised.
Figure 4. Belt Installation
Then thread it back across the front of the center
sheave in the top groove.
Assembly 11
29929 (Rev. 3/28/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
It is assumed that the mower is adjusted to run approx-
imately level. If the front of the mower is down, the
idlers will have to be raised. If the back of the mower is
down, the idlers will have to be down further. Belts
must be in proper alignment with sheave grooves as
shown in Figure 6 through Figure 8.
PTO Pulleys
PTO Pulleys must be moved in or out to cause the belt
to be in alignment with the idlers.
Belt Tension
Run belts very tight. Slipping will heat and ruin a belt
but tension is not harmful.
Use of Straight Edge (Side View)
Figure 5. Belt Installation
Proper Twist: The belt then follows with a 3/4 twist
back under the left V-idler, up over the drive sheave
and back down under the right idler pulley. This will
leave a 1/4 twist in the section of belt extending from
the right V-idler to lower groove of the center mower
sheave. If not installed correctly, more twist will result
than is allowable.
Adjust the mower to proper cutting height. The front of
the mower should be slightly lower than the rear for the
best cutting and least power requirement.
Idler Adjustment: Make minor belt adjustment with
idlers but keep left idler about 1" above being in line
with the groove in which the belt runs on the center
sheave of the mower and right idler about 1" below.
Move mower fore and aft for major adjustments.
Figure 6. Use of Straight Edge
How to Align a Twisted Belt
Belt Troubleshooting
Right: Inside edges of the belt are approximately lined
up with the sheave.
Belt Whip
Belt whip is caused by belt misalignment unless mower
is driven by a rough-running or 2-cylinder engine. On
certain models a belt guide is provided to dampen out
the whip on the loose side. The guide should be set to
just clear the belt in normal position.
Proper Position of 59
Adjust mower forward and back to such a position that
the rear take-up idlers are near the bottom of their slots
when the belt lines up with the proper groove in the
center pulley and is tight. Never run the idlers high in
the slots as this will cause misalignment.
Figure 7. Correct Alignment
12 Assembly
29929 (Rev. 3/28/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
Wrong: Outer edge of belt appears to be in line.
long slots. Remove side shields. Leave side skids on. If
optional front roller has been installed, it must be
removed.
On mowers with bent-down front frame, remove center
baffle and drill two 7/16 diameter holes in front of
mower at the dimensions shown on page 21.
Attach slotted angles (2) to leaf mulcher as shown in
drawing.
Place leaf mulcher over blades on mower. Attach
angles (2) to mower side shields to side frame angle on
mower. Mowers with bolt-on front shields will use front
shield hole to attach angle (2). Bolt side shields to
mower using 3/8 flat washers for spacers.
Figure 8. Incorrect Alignment
V-Belt Shield (See page 16)
Place the V-belt shield (43) over the rear drive and
secure with wing nut.
On mowers with bolt-on front shield, bolt front of leaf
mulcher to bottom of slots in front shield with 3/8 x 1"
bolts and flat washers. On mowers with bent-down
front frame, bolt leaf mulcher to inside of mower in
holes drilled in front frame using 3/8 x 1-1/2" bolts and
5/8 long pipe spacers between leaf mulcher and
mower. On some mowers where 5/8" pipe may be too
long, substitute 3/8 flat washers.
Casters
The caster bundle includes one right and one left
caster assembly, which, on most tractors, is assembled
with the offset away from front wheels, but on 59CL
mounted on IH Cub Lo-Boy, the left caster must be off-
set away from carburetor on the tractor. Therefore,
right caster will offset outward toward front tire. The
front tractor wheels should be moved out about 6" from
narrowest position to provide room for caster wheel to
turn when backing up.
Drill 7/16 holes in rear of mower deck through holes in
leaf mulcher rear plates and bolt rear of leaf mulcher to
deck using 3/8 x 1" bolts.
Tighten all bolts securely. Turn each blade individually
inside the leaf mulcher to see that it clears the leaf
mulcher rings. If necessary, the rings may be re-
shaped with a hammer to clear the leaf mulcher rings.
Leaf Mulcher
Turn mower upside down on saw horses. If mower has
a bolt-on front shield, adjust shield all the way down in
Figure 9. 59CL-4 Idler Bracket and Mounting Assembly Photo
Assembly 13
29929 (Rev. 3/28/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 10. 59CL-4 Lift Assembly & Caster Assembly Photo
14 Assembly
29929 (Rev. 3/28/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
DEALER CHECK LISTS
PRE-DELIVERY CHECK LIST
(DEALER’S RESPONSIBILITY)
DELIVERY CHECK
(DEALER’S RESPONSIBILITY)
Inspect the equipment thoroughly after assembly to
ensure it is set up properly before delivering it to the
customer. The following check lists are a reminder of
points to inspect. Check off each item as it is found sat-
isfactory or after proper adjustment is made.
___ Instruct customer how to lubricate and explain
importance of lubrication.
___ Point out the safety decals. Explain their meaning
and the need to keep them in place and in good
condition. Emphasize the increased safety haz-
ards when instructions are not followed.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Present Operator's Manual and request that cus-
tomer and all operators read it before operating
equipment. Point out the manual safety rules,
explain their meanings and emphasize the
increased safety hazards that exist when safety
rules are not followed.
___ Check that shields and guards are properly
installed and in good condition. Replace if dam-
aged.
___ Properly attach implement to tractor and make all
necessary adjustments.
___ Check all bolts to be sure they are tight.
___ Show customer the safe, proper procedures to be
used when mounting, dismounting, and storing
equipment.
___ Check and grease all lubrication points as identi-
fied in “Service”.
___ Check that blades have been properly installed.
___ Point out all guards and shields. Explain their
importance and the safety hazards that exist
when not kept in place and in good condition.
Assembly 15
29929 (Rev. 3/28/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
59CL-4 & 59CLF-4 MAIN ASSEMBLY
53 - COMPLETE DECAL SET
61 - FRENCH SAFETY DECAL SET
29929 (Rev. 3/28/2008)
16 Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
59CL-4 & 59CLF-4 MAIN ASSEMBLY
NOTE: Mower frames sold after 1976 the front side of mower is formed down. Before they had a bolt-on front shield.
Key For Number Used Columns
A Serial Number 100 through 306 (59CL-1)
B Serial Number 307 through 478 (59CL-2)
C Serial Number 479 through 822 (59CL-3 & 59CLF-3)
D Serial Number 823 and up (59CL-4 & 59CLF-4)
REF PART
A
B
C
D
DESCRIPTION
REF PART
A
B
C
D
DESCRIPTION
41
41A
42
3493
1505
1506
3501
3492
4152
4336
6095
-
1
1
-
-
1
-
1 PTO Sheave, 1BK 6.1H
- PTO Sheave, 1BK 7.4H
1 10-Spline bushing with bolts
1 Rear V-belt shield
1
2
3
4
5
6
7
8
9
9700
4141
5818
25506
4176
484
1
1
1
1
1
1
1
2
-
1
1
1
1
1
1
1
2
2
-
1
1
1
1
1
1
1
2
2
-
1 Frame shipping unit
1
1
-
1 Right side skid
1
1
1
-
1 Front shield (prior to 1975)
1 Right belt shield
43
44
-
-
1 W172 V-Belt, special -or-
- W180 V-Belt, special
1 Upper attachment arm
1 5/8 x 1 x 7/16 HT Sleeve
1 Chain attachment bracket
2 3/8 NC x 5 Open eyebolt
2 2/0 Straight link chain 10-link
44
1
2
2
1
2
2
45A
45B
2
2
2 V-Groove idler w/ bearing, rt
4174
4153
4215
2 .626 ID x 1.85 OD Ball
bearing
45C 4335
2
2
2
2 4.50 OD V-Groove idler
sheave less bearing, right
10 18336
-
2 Caplug, 1-1/16 - 121D SAE
thread -or-
46
47
48
49
51
4227
3885 *
4226
6126
-----
3
3
2
1
3
3
3
2
1
3
3
3
2
1
3
3 H3/4 Strt bushing w/ bolts
3 3/16 x 3/16 x 1-1/4 Key
2 1 BK 3.9H Sheave
10
11
4155
-----
2
2
2
2 1/4 Cold shut repair link (not
shown)(on earlier models)
** ** ** 1 Pair of casters
(see page 20 )
1 3 BK 3.9PD H Sheave
3 Spindle & blades (see
page 19)
21 25557
22 25555
-
-
-
-
-
-
1 Center belt shield bracket
1 Center belt shield -or-
53
5753 †
-
-
-
-
-
-
-
-
1
-
-
-
-
-
-
-
-
-
-
-
1
-
-
-
-
-
-
-
-
-
-
-
1
-
-
-
1 Complete decal set
22
4130
1
1
1
1 Center shield (for mowers
prior to mid 1975)
54 25512 †
55 25508 †
56 25532 †
57 25509 †
58 25531 †
59 26516 †
60 26520 †
61 52310 †
67 24597 *
1 Right side shield with baffle
1 Front corner baffle
23 25507
24 4142
25 25513
1
1
1
-
1
1
1
-
1
1
1
1
1
6
4
2
2
1
-
1 Left belt shield
1 Center baffle rear mtg angle
1 Center baffle
1 Left side skid
1 Left side shield
1 Center baffle frt mtg lug
2 Front toe guard with safety
1 Side discharge chute
1 French safety decal set
6 3/8NC x 3/4 Carriage bolt
2 3/8 NC x 1 Carriage bolt
12 3/8 NC Flange lock nut
26
27
-----
-----
1 Channel brace
1
4
4
2
2
-
1
4
4
2
2
-
1 Frame angle
28
2688 *
4097
410
6 1/8 Safety pin
29
4 5/8 x 1-1/2 Clevis pin
2 5/8 x 1-3/4 Clevis pin
- Rear shield
29A
30
68
6697 *
4145
69 14350 *
31 13870
1 Right vertical push arm
- Attachment arm
70
71
72
73
74
75
76
77
78
79
1263 * 35 35 31 22 3/8 NC x 1" HHCS GR5
976 * 5 3/8 NC x 1-1/2 HHCS GR5
835 * 41 41 36 36 3/8 NC Hex nut
3298 * 4 3/8 NC Hex nut plated
838 * 46 46 41 41 3/8 Lock washer
31A
32
-----
2
-
2
-
5
5
5
3369
1
2
-
1 Rt attach place (CLF only)
2 Push channel with clevis bar
- Adjustment arm
33 13314
-
-
4
4
4
33B
34
4160
3504
2
-
2
-
1
1
-
1 1/2 x 5/8 x 1-1/16 Sleeve HT
1 Crosswise rear support
- Offset pipe frame
- Guide rod
565 *
1287 *
4119
9
1
9
2
11 11 3/8 Flat washer
2 3/8 NC Wing nut
35 13313
-
-
2
35A
35B
4165
4159
1
1
-
1
1
6
12 12 12 12 1/2 NF x 1 HHCS GR5
-
745 *
742 *
1
3
1
3
-
-
- 1/2 NC x 1-1/4 HHCS GR5
35C 1791
-
- 5/8 x 1 x 9/16 HT Sleeve (for
raising fast-hitch)
- 1/2 NC x 1-3/4 HHCS GR5
(NS)
35D 4156
1
2
-
1
2
-
-
- 3/8 U-Bolt
80
81
82
83
84
948 *
-
-
3
5
3 1/2 NC x 2 HHCS GR5
2 1/2 NC Hex nut
36
37
38
39
5655 *
2
1
1
1
1
2 5/8 NC x 3-1/2 Carriage bolt
1 Upper idler bracket
1 Lower idler bracket
1 Left attach plate (CLF only)
1 Left vertical push arm
1093 *
4
4
3510
3506
3368
855 * 16 16 17 14 1/2 Lock washer
-
-
854 * 12 12
6268 *
3
8
2 1/2 Flat washer
-
-
-
-
8 5/8 NC x 1-1/4 HHCS GR5
40 13871
-
-
29929 (Rev. 3/28/2008)
Parts 17
Download from Www.Somanuals.com. All Manuals Search And Download.
59CL-4 & 59CLF-4 MAIN ASSEMBLY CONTINUED
REF PART
A
B
C
D
DESCRIPTION
REF PART
A
B
C
D
DESCRIPTION
95 12169 *
96 13258
4
-
4
-
4
2
-
4 3/8 NC x 1-1/4 HHCS, GR5
2 5/8 x 1-3/8 x 5/8 Flat washer
3 1/2 NC Flange lock nut
85
86
87
88
89
90
91
92
93
94
738 *
4
3
8
1
8
4
3
8
1
8
-
- 5/8 NC x 1-1/2 HHCS GR5
3 5/8 NC x 1-3/4 HHCS GR5
4 5/8 NC Hex nut
614 *
230 *
3
4
1
97 11900 *
-
-
6239 *
1286 *
1 5/8 Lock nut
* Obtain locally
12 12 5/8 Lock washer
** The 6760 casters may be used on “A”, “B”, & “C”
machines by drilling two 13/32 diameter holes 4" apart,
through frame angle, the first hole being 3-1/2" from
front end of frame angle. For repair of “A”, “B” & “C”
series casters, see page 20 drawing and parts list.
† For mowers sold after 1976. See note on previous
page.
692 * 13 13 13 13 5/8 Flat washer
3627
1
8
-
1
8
-
-
- 1" Shakeproof washer
2457 *
1985 *
-----
8
6
1
3 1/4 NC x 3/4 HHCS GR5
6 1/4 Standard lock washer
1 Leaf mulcher (see page 21)
1
1
29929 (Rev. 3/28/2008)
18 Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
SPINDLE ASSEMBLY
REF PART QTY
DESCRIPTION
1
2
4116
5089
4114
1
2
1
1
2
1
2
1
1
1
1
1
1
1
1
2
1
1
Spindle
Seal
3
Sleeve
Pin
4
4115
5
4107
4117
Bearing cone
6
Housing with cups
Bearing cup
7
4106
1972
4105
4110
8
Grease fitting
9
Spindle shaft
10
11
Shoulder washer
20-1/4 Medium suction blade
20-1/4 Low suction blade
5/8 NC x 1-1/2 Nylok bolt
Blade bolt wrench
Spindle lock wrench
5/8 Cup washer
6950KT
11 26559KT
12
13
14
16
17
10658
3490
2974
10635
692
5/8 Flat washer
18 1015825
Blade bolt and washers, complete
NOTE: When difficulty is experienced with a
mower spindle, time and trouble will be saved
by buying a complete new assembly.
NOTE: Repair shaft (9) and repair sleeve (3) do
not have a hole drilled in them for pin (4). After
new parts have been assembled and proper bearing
adjustment obtained, drill a 3/16 diameter hole
through sleeve and shaft. Drive in Sel-lock pin to
hold proper bearing adjustment.
29929 (Rev. 3/28/2008)
Parts 19
Download from Www.Somanuals.com. All Manuals Search And Download.
59 & L59 CASTERS
REF PART
QTY
DESCRIPTION
1
2
29750
1
1
59 & L59 Right & left caster bundle
12243
Caster yoke (includes bolt, nut & 2
sleeves)
3
29746 (a)
1
Right caster arm asy, 13-5/32 long
-or-
3
4
4
5
7
6761 (a)
29747 (a)
18424 (a)
19703
1
1
1
1
1
Right caster arm, 16-5/32 long
Left caster arm, 13-5/32 long -or-
Left caster arm, 16-5/32 long
8" HD Caster wheel with sleeve
2909 *
Straight 1/4 self-tapping grease fitting
(for steel wheel) -or-
7
195 *
1
Straight 1/8P thread grease fitting (for
polyethylene wheel)
8
8
9
21020
1
1
1
1/4 x 1-1/4 Spirol pin -or-
1285 *
12296 *
1/4 x 1-1/2 Cotter pin
1/4 - 28 Straight grease fitting 15/32"
long
10
11
12
13
14
15
15
16
12169 *
838 *
2
2
2
1
1
1
1
2
3/8 NC x 1-1/4 HHCS GR5
3/8 Standard lock washer
3/8 NC Hex nut, plated
835 *
765 *
1/2 NC Hex lock nut
23479
1/2 NC x 5 HHCS GR5
29368 (c)
12242 (c)
29375 (b)
1/2 x 3/4 OD x 3-3/8 Sleeve -or-
17 GA Wall x 5/8 OD x 3-3/8 tube
3/4 Bore flanged bearing for 1-1/8
hole -or-
16
16
16
4228 (b)
2905 (b)
2
2
2
5/8 Bore flanged bearing for 1-3/8
hole -or-
5/8 Bore flanged bearing for 1-1/8
hole -or-
65578 (b)
3/4 Bore x 1.385 flanged wheel
bearing with groove
17
18
22240
4181
2
2
3/4 x 1-3/16 x 10 GA Washer
25/32 x 1 x 1/2 Heat-treated sleeve
* Obtain locally
(a) For proper caster arm identification, refer to
dimension “L” as shown on drawing. The caster arms
may be used on either side to obtain best fit.
(b) Measure old bearing.
(c) Measure outside diameter of old sleeve.
29929 (Rev. 3/28/2008)
20 Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
LEAF MULCHER
REF PART
QTY
DESCRIPTION
A
A
1
7080
1
1
1
1
1
Model 59 Leaf mulcher -or-
Model L306 Leaf mulcher
Leaf mulcher weldment
Angle lug
13482
-----
2
7076
23218
5
3/8 Schd 40 pipe 5/8 long
3/8 NC x 1 HHCS GR5
3/8 NC x 1-1/2 HHCS GR5
3/8 Flat washer
7
839 *
8
979 *
565 *
838 *
835 *
9
10
11
3/8 Lock washer
3/8 NC Hex nut
*
Standard hardware, obtain locally
29929 (Rev. 3/28/2008)
Parts 21
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
SAE 5
A
SAE 2
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
Coarse Thread
Marking on Head
Metric 8.8 Metric 10.9
Fine Thread
Marking on Head
Metric 8.8 Metric 10.9
A
A
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Size
N-m
lbs-ft
6
N-m
lbs-ft
8
N-m
lbs-ft
6
N-m
lbs-ft
8
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
11
29
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Bolt Torque & Size Charts (Rev. 3/28/2007)
22 Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
MPa.........................................................Mega Pascal
N.......................................................................Newton
NC......................................................National Coarse
NF ...........................................................National Fine
NPSM.....................National Pipe Straight Mechanical
NPT.......................................... National Pipe Tapered
NPT SWF .........National Pipe Tapered Swivel Female
ORBM .......................................... O-Ring Boss - Male
P...........................................................................Pitch
PBY...................................................... Power-Beyond
psi..........................................Pounds per Square Inch
PTO..................................................... Power Take Off
QD....................................................Quick Disconnect
RH..............................................................Right Hand
ROPS........................... Roll-Over Protective Structure
RPM ........................................Revolutions Per Minute
RT ....................................................................... Right
SAE..........................Society of Automotive Engineers
UNC .....................................................Unified Coarse
UNF...........................................................Unified Fine
UNS......................................................Unified Special
ASABE.................... American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE ....... American Society of Agricultural Engineers
ATF ............................... Automatic Transmission Fluid
BSPP .............................British Standard Pipe Parallel
BSPTM ................British Standard Pipe Tapered Male
CV.....................................................Constant Velocity
CCW .............................................. Counter-Clockwise
CW............................................................... Clockwise
F ...................................................................... Female
FT .............................................................. Full Thread
GA .................................................................... Gauge
GR (5, etc.) ........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT........................................................... Heat-Treated
JIC .................Joint Industry Council 37° Degree Flare
LH.................................................................Left Hand
LT........................................................................... Left
m......................................................................... Meter
mm................................................................Millimeter
M.......................................................................... Male
Bolt Torque & Size Charts (Rev. 3/28/2007)
Appendix 23
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
Model Number: ____________________________
From (Dealer): ___________________________________________
Serial Number: ___________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
Woods backhoe models BH70-X, BH80-X, and BH90-X are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Duration (from date of delivery
Model Number
to the original purchaser)
BW1260, BW1800
8 years
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X,
BB7200X, BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-2, BW180-2
6 years
Gearbox
components
PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,
RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2, 5 years
9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD
3 years (1 year if used in rental or
commercial applications)
RDC54, RD60, RD72
RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2,
9180RD-2, 9204RD-2
Blade spindles
Rust-through
3 years
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-2, BW180-2,
BW1260, BW1800, 2162, 3240, DS1260, DSO1260, DS1440, TS1680
10 years
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made
with parts other than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to
a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,
its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-3079 (Rev. 4/4/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(Replacement Parts For All Models Except Mow’n Machine
Zero-Turn Mowers and Woods Boundary Utility Vehicles)
TM
TM
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 6/23/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
©2007 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and “Tested. Proven. Unbeatable.” are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|