Safety Instructions & Operator’s Manual for
21” STEEL DECK
WALK MOWERS
(TYPE ‘M’)
SERIES 18
MODELS
MR216518B
MRP216518B
MODEL NUMBER EXPLANATION
MR
P
21
65
18
B
MODEL DESIGNATION
SELF-PROPELLED
CUTTING WIDTH
ENGINE DESIGNATION
SERIES DESIGNATION
ENGINE HORSE POWER *
M – Model Designation
R – Recycling Model
P – Self Propelled Model
21 – 21” Cutting Width
65 – 6.5 HP *
18 – Series Designation
B – Briggs & Stratton
Thank you for buying a SNAPPER Product! Before operating your Walk Behind, read this manual carefully and
pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 - 4. Remember that all power
equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in
accordance with the operating instructions and common sense.
NOTE: Specifications are correct at time of printing and are subject to change without notice.
* Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors.
COPYRIGHT © 2004
SNAPPER – A DIVISION OF SIMPLICITY MFG., INC.
ALL RIGHTS RESERVED
MANUAL No. 2-9755 (I.R. 7/29/04)
IMPORTANT SAFETY INSTRUCTIONS
SAFE HANDLING OF GASOLINE
(Continued From Previous Page)
OPERATION
(Continued From Previous Column)
3. DO NOT remove fuel cap or add fuel with the engine
running. Allow the engine to cool before refueling.
4. DO NOT refuel the machine indoors.
5. DO NOT store the machine or fuel container inside
where there is an open flame, spark or pilot light
such as on a water heater or other appliances.
6. DO NOT fill fuel containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always place
the containers on the ground away from the vehicle
before filling.
7. Remove gas-powered equipment from the vehicle or
trailer and refuel it on the ground. If this is not
possible, then refuel equipment using a portable
container, rather than a gasoline dispenser nozzle.
8. DO NOT start gas powered equipment in enclosed
vehicles or trailers.
11. Before cleaning, repairing or inspecting make
certain engine, blade and all moving parts have
STOPPED. Disconnect and secure spark plug wire
away from plug to prevent accidental starting.
12. STOP engine and wait until the blade comes to
complete STOP before removing grass bag and/or
clearing grass.
13. DO NOT operate mower without the entire grass
catcher, discharge guard, rear guard or other safety
devices in place and working. DO NOT point discharge
at people, passing cars, windows or doors.
14. DO NOT discharge material against a wall or obstruction.
Material may ricochet back towards the operator.
15. Slow down before turning.
16. Watch out for traffic when near or crossing
roadways.
9. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. DO NOT use a nozzle lock-open device
10. If fuel is spilled on clothing, change clothing
immediately.
17. DO NOT operate engine in enclosed areas. Engine
exhaust gases contain carbon monoxide, a deadly
poison.
18. Only use accessories approved by the manufacturer. See
manufacturer’s instructions for proper operation and
installation of accessories.
11. DO NOT overfill a fuel tank. Replace fuel cap and
tighten securely.
MAINTENANCE AND STORAGE
OPERATION
1. DO NOT store mower or fuel container inside where
fumes may reach an open flame, spark or pilot light
such as in a water heater, furnace, clothes dryer or
other gas appliance. Allow engine to cool before
storing machine in an enclosure. Store fuel
container out of reach of children in a well
ventilated, unoccupied building.
1. DO NOT put hands or feet near or under rotating
parts. Keep clear of discharge area while engine is
running.
2. STOP engine when crossing gravel drives, walks, or
roads, and under any conditions where thrown
objects might be a hazard.
3. Mow only in daylight or good artificial light.
4. DO NOT operate mower while under the influence of
alcohol or drugs.
2. Keep mower and engine free of grass, leaves or
excess grease to reduce fire hazard and engine
overheating.
5. After striking a foreign object or if mower vibrates
abnormally, STOP the engine, disconnect and
secure spark plug wire. Inspect the mower for any
damage and repair the damage before starting.
6. DO NOT mow near drop offs, ditches or
embankments. Operator could lose footing or
balance.
7. STAY ALERT for holes and other hidden hazards.
Tall grass can hide obstacles. Keep away from
ditches, washouts, culverts, fences and protruding
objects.
3. When draining fuel tank, drain fuel into an approved
container outdoors and away from open flame.
4. Keep all bolts, especially blade bolts, nuts and
screws properly tight. Check that all cotter pins are
in proper position.
5. Always provide adequate ventilation when running
engine. Engine exhaust gases contain carbon
monoxide, a deadly poison.
6. Service engine and make adjustments only when
engine is stopped. Removed spark plug wire from
spark plug and secure wire away from spark plug to
prevent accidental starting.
7. DO NOT change engine governor speed settings or
overspeed engine.
8. DO NOT mow on wet grass. Always be sure of your
footing. Keep a firm hold on the handle and walk,
never run. Slipping could cause injury.
9. ALWAYS stay behind handle when engine (motor) is
running.
10. DO NOT leave the machine with the engine running.
STOP BLADE and STOP ENGINE before leaving the
operators position for any reason.
8. Check grass bag assembly frequently for wear or
deterioration to avoid thrown objects and exposure
to moving parts. Replace with new bag if loose
seams or tears are evident. Replace slider or bag
adapter if broken or cracked.
9. Mower blades are sharp and can cut. Wrap the
blades or wear heavy leather gloves and use
CAUTION when handling them.
3
IMPORTANT SAFETY INSTRUCTIONS
MAINTENANCE AND STORAGE
(Continued From Previous Page)
10. DO NOT test for spark by grounding spark plug next
to spark plug hole; spark plug could ignite gas
exiting engine.
11. Have machine serviced by an authorized SNAPPER
dealer at least once a year and have the dealer install
any new safety devices.
12. Use only genuine SNAPPER replacement parts to
assure that original standards are maintained.
4
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS...................................................................... 2 - 4
TABLE OF CONTENTS......................................................................................................5
SECTION 1 - FAMILIARIZATION.......................................................................................6
SECTION 2 - OPERATING INSTRUCTIONS............................................................... 7-11
Pre-start Checklist................................................................................................7
Starting & Stopping Engine & Blades................................................................7
Starting & Stopping Wheel Drive........................................................................8
Handle Height Adjustment ..................................................................................8
Cutting Height Adjustment..................................................................................8
Recycling Operation.............................................................................................9
Installation of Grass Catcher (Door Type)................................................... 9-10
Installation of Grass Catcher (Slide Closure Type) ........................................10
Installation of Discharge Deflector & Recycling Cover..................................11
SECTION 3 - MAINTENANCE INSTRUCTIONS ....................................................... 12-13
Change Engine Oil..............................................................................................12
Check Transmission Grease....................................................................... 12-13
Check Mower Blade ...........................................................................................13
Check Engine Drive Belt....................................................................................13
Check Transmission Poly-V Belt ......................................................................13
Service - Annually ..............................................................................................13
Engine ..............................................................................................................13
Air Filter............................................................................................................13
Engine Oil.........................................................................................................13
Storage Procedure .............................................................................................13
SECTION 4 - ADJUSTMENTS AND REPAIR............................................................ 14-21
Mower Blade Replacement................................................................................14
Blade Sharpening......................................................................................... 14-15
Wheel Drive Control Adjustment ......................................................................15
Driven and Drive Disc Service .................................................................... 16-19
Cleaning Drive Disc and Driven Disc............................................................16
Drive Spring Repair/Replacement.................................................................16
Driven Disc Adjustment............................................................................ 16-17
Driven Disc Replacement......................................................................... 17-18
Driven Disc Bearing Replacement ................................................................18
Hex Shaft Bearing Replacement....................................................................19
Belt Service................................................................................................... 19-20
Engine Drive Belt Replacement............................................................... 19-20
Transmission Poly-V Belt Replacement .......................................................20
Battery Service ...................................................................................................21
TROUBLESHOOTING......................................................................................................22
SERVICE SCHEDULE......................................................................................................23
Maintenance/Replacement Parts......................................................................23
WARRANTY......................................................................................................................24
PRIMARY MAINTENANCE ........................................................................................ 25-28
PRODUCT REGISTRATION FORM.................................................................................29
5
Section 1 - FAMILIARIZATION
WHEEL DRIVE
CONTROL
BLADE
CONTROL
IMPORTANT
The figures and illustrations in this manual are
provided for reference only and may differ from
your specific model. Contact your Snapper
dealer if you have questions.
GROUND SPEED
CONTROL
ROPE START
HANDLE
FUEL FILLER
CAP
OIL FILL CAP
AND DIPSTICK
REAR HEIGHT
ADJUSTMENT
LATCH
ENGINE
PRIMER
RECYCLING
COVER
FRONT HEIGHT
ADJUSTMENT
LATCHES
FIGURE 1.1
1.1 INTRODUCTION
1.2 NOMENCLATURE
This manual has been prepared for the operators of
the SNAPPER Type ‘M’ WALK BEHIND MOWERS.
Its purpose, aside from recommending operating and
routine service requirements, is to promote safety
through the use of accepted operating practices.
Read, Understand and Follow the “IMPORTANT
SAFETY INSTRUCTIONS” on Pages 2 - 4 of this
manual and all safety messages on the mower and
attachments before operating the mower.
The nomenclature drawing above, Figure 1.1, shows
the essential parts of the SNAPPER Type ‘M’ WALK
BEHIND MOWERS. It is recommended that all
operators of the mower become thoroughly familiar
with the controls, parts and operation of the mower
before operating.
Specific details involving the
engine are found in the separate engine owner’s
manual. Study these manuals before operating and
keep both handy for future reference.
6
Section 2 - OPERATING INSTRUCTIONS
2.1 PRE-START CHECK LIST
2.2 STARTING & OPERATION
Make the following checks and perform the service
required before each start-up.
2.1.1. Check guards, deflectors, grass bag, adapter
and covers to make sure all are in place and
securely tightened.
2.2.1. ENGINE & BLADE
1. Push primer button three times to start a cold
engine. See Figure 2.3. NOTE: The primer should
not be required to restart a warm engine.
2.1.2. Check blade control and wheel drive control
to insure they work freely. See Figure 2.1.
PRIMER
BUTTON
(PUSH 3X)
BLADE
CONTROL
WHEEL
DRIVE
CONTROL
FIGURE 2.3
2. Pull blade control against handle. See Figure
2.4.
FIGURE 2.1
3. Pull rope start handle to crank engine.
2.1.3. Check cutting height. Adjust to desired height.
2.1.4. Check engine oil and add oil as needed to bring
level up to the full mark. Refer to Engine Owner’s
Manual for oil specifications. See Figure 2.2.
BLADE
CONTROL
ROPE START
HANDLE
FIGURE 2.4
FIGURE 2.2
4. After engine starts, allow a brief warm-up until
engine runs smooth.
2.1.5. Add fuel to tank after pushing the mower
outside where fumes can safely dissipate. Make sure
cap is tightened after refueling. Refer to Engine
Owners Manual for specifications.
NOTE: To stop the engine (and blade), release the blade
control.
2.1.6. Clean exterior surfaces of cutting deck and
engine of any accumulation of spilled fuel, dirt, grass,
oil, etc. Keep engine air intake screen and cooling
fins clear at all times.
7
Section 2 - OPERATING INSTRUCTIONS
2.2 STARTING & OPERATION
2. Move upper mower handle up or down until the
desired position is achieved.
2.2.2. PROPELLING MOWER
(Self Propelled Models Only)
1. Start engine. Refer to Section “Starting &
Operation”.
3. Tighten the lower nuts on each lower handle to
maintain desired position.
2. Move ground speed control to the desired speed
position. See Figure 2.5.
WARNING
Stop engine and mower blade by releasing the blade
control before adjusting cutting height.
3. Move wheel drive control against handle to
engage wheel drive and propel mower forward.
Forward speed can be adjusted while the mower is
moving by changing position of the ground speed
control. See Figure 2.5.
2.5 CUTTING HEIGHT ADJUSTMENT
1. Pull the height adjusting latch outward and move
to desired cutting height. See Figure 2.7.
ENGAGE
LOWEST CUTTING
HEIGHT
1
LATCH
WHEEL
DRIVE
CONTROL
GROUND
SPEED
SIXTH
CONTROL
SHOWN IN
FIRST/SLOW
FIRST
1
2
3
4
HIGHEST
CUTTING
HEIGHT
6
5
FIGURE 2.5
6
2.3 STOPPING
Stop engine and blade by releasing the blade
control. Stop forward motion of mower by releasing
the wheel drive control.
FIGURE 2.7
2.4 HANDLE HEIGHT ADJUSTMENT
The height of the mower handle can be adjusted as
follows:
2. Set all wheels at the same cutting height. The
highest cutting position is Notch 6. The lowest
cutting position is Notch 1. See Figure 2.8.
1. Loosen the lower nuts on each lower handle as
shown in Figure 2.6.
HIGHER
LATCH
POSITIONS
LOWER
HANDLE
LOWER
CUTTING HEIGHT SETTINGS
LOOSEN LOWER
NUTS ON EACH
LOWER HANDLE
FIGURE 2.8
FIGURE 2.6
8
Section 2 - OPERATING INSTRUCTIONS
2.8 INSTALLATION of RECYCLING PLUG
(Optional Accessory on Some Models)
STEP 1: Once adapter has been installed, recycling may
be desired. Insert recycling plug completely and securely
into adapter. Install grass bag. See Figure 2.10.
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
INSERT RECYCLING PLUG
COMPLETELY AND SECURELY
PLUG
INTO ADAPTER. INSTALL
GRASS BAG.
2.6 RECYCLING OPERATION
NOTE: For best recycling results, cut up to a maximum of
1/3 of grass blade length and recycle ONLY when grass
is dry.
1. Set all wheels in the highest cutting position
(Notch 6).
2. Move ground speed control to slowest speed
setting.
ADAPTER
3. Proceed mowing slowly. If grass is very dense,
lower each rear wheel latch one notch lower than
the front wheel latches to improve recycling
performance.
2.7 INSTALLATION of GRASS BAG ADAPTER
(Optional accessory on some models)
STEP 1: Install the grass bag adapter and secure to the
side and top of the deck with the two nuts provided on the
machine. Slot in front edge of adapter must be under nut
located on top of deck. See Figure 2.9.
FIGURE 2.10
2.9 INSTALLATION of GRASS CATCHER – DOOR
BAG
ROUTE RECOIL
ROPE AROUND
ADAPTER PULLEY
(Optional accessory on some models)
Install grass catcher by sliding connector over flange
of adapter. See Figure 2.11. Attach grass bag hooks
over middle handle cross bar. See Figure 2.12.
BE SURE
ADAPTER SLOT
SLIPS UNDER
DECK NUT
POSITION BAG
BETWEEN HANDLES
SECURE
WITH NUTS
SLIDE
CONNECTOR
DOWN OVER BAG
ADAPTER FLANGE
ADAPTER
CONNECTOR
FIGURE 2.9
STEP 2: Route recoil rope around pulley on top of bag
BAG
adapter. See Figure 2.9.
ADAPTER
FIGURE 2.11
(Continued On Next Page)
9
Section 2 - OPERATING INSTRUCTIONS
HOOK BAG
HANDLE OVER
LOWER HANDLES
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
2.9 INSTALLATION of GRASS CATCHER – DOOR
BAG
(Optional accessory on some models)
MIDDLE
HANDLE
CROSS BAR
SLIDE CONNECTOR
OVER END OF
ADAPTER FLANGE
FIGURE 2.14
2.11 REMOVING and DUMPING GRASS CATCHER –
Slide Closure Type
1. Grasp bag connector and bag handle as shown.
See Figure 2.13.
2. First, lift up on bag handle, removing it from the
mower handle. Then lift up on bag connector
removing it from the adapter flange.
ATTACH BAG HOOKS
OVER MIDDLE HANDLE
CROSS BAR
FIGURE 2.12
3. Dump bag by pulling bag slider off of Z-Fold at
rear of bag, opening bag.
2.10 INSTALLATION of GRASS CATCHER – Slide
Closure Type
4. To close bag, fold rear of bag into Z-shape,
keeping edges aligned. Note: an illustration of
folding the Z-shape is attached to the bag.
5. Grasp the edge of the Z-fold, and while holding
the slider, pull the Z-fold fully into the slider. See
Figure 2.15.
(Optional accessory on some models)
1. Position grass bag between handles. See
Figure 2.13. Install grass catcher by sliding
connector over flange of adapter. Attach grass
bag hooks over middle handle cross bar. See
Figure 2.14.
LOWER HANDLES
HANDLE
GRASP SLIDER. PULL
Z-FOLD INTO SLIDER
BAG CONNECTOR
PULL
FIGURE 2.15
ADAPTER
FLANGE
FIGURE 2.13
10
Section 2 - OPERATING INSTRUCTIONS
2.13 INSTALLATION of RECYCLING COVER
(Optional Accessory on Some Models)
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP
engine and blade. Disconnect spark plug wire and
secure away from spark plug. Engine and
components are HOT. Avoid serious burns, allow
sufficient time for all components to cool.
It will be necessary to remove bag adapter and grass
bag or discharge deflector before installing recycling
cover. See previous section for instructions. Install the
recycling cover and secure to the side and top of the
deck with the two nuts provided on the machine. Slide
top portion of cover under nut secured to the deck. See
Figure 2.17.
2.12 INSTALLATION of DISCHARGE DEFLECTOR
(Optional accessory on some models)
RECYCLING
COVER
Install discharge deflector if discharging is desired.
Grass Bag and Bag Adapter or Recycling Cover must
be removed.
1. Remove front and rear nuts that secure Bag
Adapter or Recycling Cover to deck. Refer to
sections concerning these parts.
2. Install discharge deflector and secure to deck
using hardware removed in Step 1. Slot in front
edge of discharge deflector must be under nut as
shown and both bolts protruding through holes in
the side of the deflector. See Figure 2.16.
SLIDE
INSTALL
DEFLECTOR SLOT
UNDER NUT
DISCHARGE
DEFLECTOR
ATTACH RECYCLING
COVER TO THE DECK
WITH TWO NUTS
FIGURE 2.17
WARNING
DO NOT operate without entire Grass Catcher or
guard in place. Grass Catcher components are
subject to deterioration during normal use. Inspect
frequently and replace worn or damaged
components immediately.
INSTALL
NUTS
FIGURE 2.16
WARNING
Grass Catcher bags used on SNAPPER products
are made of woven fabric, and are subject to
deterioration and wear during normal usage.
Check condition of bag before each use.
Immediately replace worn or damaged catcher bags
with only bags recommended by SNAPPER. The
grass catcher is optional equipment on some
models.
11
Section 3 – MAINTENANCE
3.1 INTRODUCTION
To retain the quality of the mower, use genuine
SNAPPER replacement parts only. Contact a local
SNAPPER dealer for parts and service assistance.
For the correct part or information for a particular
mower, always mention model and serial number.
3. Dispose of drain oil properly.
4. Fill engine with oil as specified in Engine Manual.
Do Not overfill.
3.2.2. CHECK GREASE LEVEL IN TRANSMISSION
1. Remove transmission fill plug. Roll machine
forward or backward while looking down into plug
hole.
2. If liquid grease IS NOT visible on the input gear
(the small gear below the plug hole), add an
amount, to cover gear, of Snapper “00” grease. See
Figure 3.2.
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
3.2 SERVICE - AFTER FIRST 5 HOURS
3.2.1. CHANGE ENGINE OIL
FILL PLUG
IMPORTANT: Drain fuel tank before tipping machine.
DO NOT tip machine with carburetor or spark plug down.
Oil from crankcase will saturate the air filter and cause the
engine to be hard to start or not start at all. If
contamination does occur, the air filter will have to be
replaced.
1. Refer to Engine Manual for proper oil
specifications, procedures and proper service
intervals.
2. For simplest/cleanest oil change, loosen lower
handle nuts. Stand mower up on lower handle
brackets as shown in Figure 3.1. Drain oil through
dipstick tube into a container. Allow sufficient time for
all oil to drain. NOTE: On self-propelled models,
wheel drive rod prohibits handles from being folded.
Simply turn mower on its side to drain oil.
FIGURE 3.2
NOTE: Snapper “00” Grease (Part No. 2-9443) is
available at your SNAPPER dealer.
FIGURE 3.1
12
Section 3 – MAINTENANCE
3.2.5. CHECK TRANSMISSION POLY-V BELT
1. Visually check poly-v belt for cracking, fraying,
severed or belt strands exposed. If worn or
damaged, replace belt before operating mower.
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool. Wear heavy leather gloves
when handling or working around cutting blades.
Blades are extremely sharp and can cause severe
injury.
RECOMMENDED
BLADE RETAINING
CAP SCREW TORQUE
VALUE SHOULD BE
40 FT. LBS.
3.2.2. CHECK GREASE LEVEL IN TRANSMISSION
NOTE: Do not spill grease or oil on surface of drive
disc. See Figure 3.3.
3. Reinstall transmission plug.
4. Check grease level after each 25 hours of
operation.
FIGURE 3.4
3.3 SERVICE - ANNUALLY
Perform all maintenance as described in the “Service
Schedule” section of this manual.
3.3.1. Engine
KEEP DRIVE DISC CLEAN!
Service engine according to engine owner’s manual.
3.3.2. Air Filter
Refer to engine owner’s manual for service
instructions.
3.3.3. Engine Oil
Refer to engine owner’s manual for service
instructions.
3.4 STORAGE PROCEDURE
Refer to the Engine Owner’s Manual for directions
regarding engine storage preparations. Prepare the
mower for “end of season” storage as follows:
1. Drain fuel from fuel tank and let engine run until
all fuel is out of the carburetor.
FIGURE 3.3
2. Disconnect and remove the spark plug wire
away from spark plug before any other
preparations are made!
3. Tape all openings closed to prevent spraying
water into exhaust or air intakes during washing.
4. Tilt mower up on its rear wheels and thoroughly
clean the underside of the deck. Do not tilt mower
with spark plug or carburetor down. Scrape away
any accumulation of grass with a putty knife and or
wire brush.
5. Lubricate all exposed metal with a light coating
of oil to prevent corrosion.
6. On self-propelled models disconnect transfer
rod clip and remove ground speed control rod
before folding handles.
IMPORTANT: Drain fuel tank before tipping mower. DO
NOT tip machine with carburetor or spark plug down. Oil
from crankcase will saturate the air filter and cause the
engine to be hard to start or not start at all. If contamination
does occur, the air filter will have to be replaced.
3.2.3. CHECK MOWER BLADE
1. Disconnect spark plug wire and secure end away
from plug.
2. Tilt mower up on its rear wheels for access to the
blade cap screw. Do not tilt mower with spark plug or
carburetor down. See Figure 3.4.
3. Check torque of blade retaining cap screw.
Recommended torque should be 40 ft. lbs.
See Figure 3.4.
7. Loosen handle knobs. Carefully fold the handles
forward, “flexing” the control cables to prevent
cable damage.
4. Check blade for sharpness, wear and damage.
Refer to Section “Blade Wear Limits”.
3.2.4. CHECK ENGINE DRIVE BELT
1. Visually check engine drive belt for cracking,
fraying, severed or belt strands exposed. If worn or
damaged, replace belt before operating mower.
8. Store the mower in a shed or other dry area,
protected from weather.
13
Section 4 - REPAIR & ADJUSTMENTS
2. Replace the blade if it is badly chipped, bent,
WARNING
noticeably out of balance or has cracks or notch in
either tip. See Figure 4.1 & 4.1A. Replace with new
blade.
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool. Wear heavy leather gloves
when handling or working around cutting blades.
Blades are extremely sharp and can cause severe
injury.
WARNING
DO NOT use a cutting blade that shows signs of
excessive wear or damage. Refer to Section
“MOWER BLADE REPLACEMENT” for proper blade
inspection and service procedures.
4.1.2. BLADE SHARPENING
1. Disconnect spark plug wire and secure end away
from plug.
4.1 MOWER BLADE REPLACEMENT
4.1.1. STANDARD BLADE WEAR LIMIT
1. Inspect blade frequently for signs of excessive
wear or damage. See Figure 4.1.
IMPORTANT: Drain fuel tank before tipping mower.
DO NOT tip machine with carburetor or spark plug down.
Oil from crankcase will saturate the air filter and cause the
engine to be hard to start or not start at all. If
contamination does occur, the air filter will have to be
replaced.
NEW BLADE
WEAR LIMIT
(NOTCH STARTS)
DANGEROUS CONDITION !
DO NOT USE ON MOWER !
REPLACE WITH NEW
BLADE.
2. Tilt mower up on its rear wheels. Do not tilt
mower with spark plug or carburetor down.
3. Remove blade. See Figure 4.3.
MAKE SURE THAT
BLADE HUB IS
SEATED
BETWEEN
FLANGES
BLADE
HUB
FIGURE 4.1
FLANGE
4.1.1.A. NINJA BLADE WEAR LIMIT
1. Inspect blade frequently for signs of excessive
wear or damage. See Figure 4.2.
BLADE
WEAR LIMIT.
NEW BLADE
CRACKS OR
NOTCHES
CONE WASHER
(Concave Side Up)
BEGIN TO
APPEAR ON TIP
CAPSCREW
FIGURE 4.3
DANGEROUS !
DO NOT USE A BLADE IN
THIS CONDITION !
FIGURE 4.2
14
Section 4 - REPAIR & ADJUSTMENTS
CLUTCH CABLE
VINYL SPRING
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
1/16” TO 1/8”
CLEARANCE
CLUTCH CABLE
EYE
UPPER
SPRING
SPRING HOOK
LOWER
SPRING
4. Sharpen blade on a grinding wheel at an angle of
22 to 28 degrees. DO NOT sharpen blade beyond
original cutting edge. See Figure 4.4.
DO NOT SHARPEN
BEYOND ORIGINAL
CUTTING EDGE
CABLE
CLUTCH CABLE EYE
22-28º
BLADE TIP
SPRING
END VIEW OF
BLADE ASSEMBLY
ORIGINAL CUTTING EDGE
FIGURE 4.5
FIGURE 4.4
2. To adjust, unhook upper spring from cable eye
and rotate spring in direction required to extend or
shorten spring length.
3. Rehook upper spring to cable eye and check
clearance. Repeat procedure if required.
5. Check blade for balance. If necessary, correct
balance by grinding heavy end of blade.
6. Reinstall blade. See Figure 4.3. Check torque of
blade retaining cap screw. Recommended torque
should be 40 ft. lbs.
NOTE: The vinyl spring cover should be kept over the
spring at all times except for adjustments.
NOTE: The following sections 4.2 through
4.4 are for self-propelled models only.
4. If the wheel drive control fails to return quickly to
the “OFF” position when released, check for binding
at the cable holdings located on the side of the right
handle. The upper clip should be located 2” below
the upper knob; the lower clip should be 4” above
the lower knob. The cable should slide freely with
the clips installed at these locations.
4.2 WHEEL DRIVE CONTROL ADJUSTMENT
1. The wheel drive control is properly adjusted
when there is 1/16” to 1/8” clearance between the
inside of the spring hook and the inside of the clutch
cable eye with the wheel drive control released. See
Figure 4.5.
15
Section 4 - REPAIR & ADJUSTMENTS
IMPORTANT: If machine drive system continues
slipping see Trouble Shooting section.
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
USE
NEEDLE
NOSE
PLIERS TO
INSTALL
DRIVE
SPRING
4.3 DRIVEN AND DRIVE DISC SERVICE
If the mower does not propel itself properly, See
Figure 4.6. Check for the following problems:
DRIVEN DISC &
RUBBER RING
POLY-V
BELT
DRIVE
SPRING
DRIVE
SPRING
ENGINE
DRIVE
BELT
DRIVE
DISC
FIGURE 4.7
4.3.3. DRIVEN DISC ADJUSTMENT
If the drive disc and driven disc are clean and the
mower drive is still slipping, adjust the driven disc as
follows:
1. Place ground speed control in the number six
speed position. See Figure 4.8.
FIGURE 4.6
1. Grease on drive disc causing slippage.
2. Broken or disconnected drive spring.
3. Driven disc is out of adjustment.
4. Driven disc rubber is worn - does not contact
drive disc properly.
MOVE GROUND
REYCLING MODEL SHOWN
SPEED CONTROL TO
(ROPE START MOUNTED ON
SIX SPEED POSITION
RIGHT SIDE OF HANDLE)
5. Worn Poly-V Belt or engine drive belt.
SIXTH SPEED
POSITION
NOTE: If any of the above (1 thru 5) are causing
problems, service as follows:
SIXTH
4.3.1. Cleaning Drive Disc & Driven Disc.
If oil or grease on the drive disc or driven disc is
causing slippage, clean discs as follows:
1. Wipe away any oil or grease with a clean cloth.
2. Use either an approved grease solvent or hot,
soapy water to clean drive disc or driven disc.
3. Rinse components with clean water.
FIRST
FIRST
SPEED
4. Dry components with a clean cloth.
4.3.2. Drive Spring Repair/Replacement
If drive spring is loose, reconnect as shown in Figure
4.7. If spring is broken, replace with new spring.
FIGURE 4.8
16
Section 4 - REPAIR & ADJUSTMENTS
WARNING
1/8” MEASUREMENT TO
OUTSIDE EDGE OF DRIVE
DISC
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
DRIVE
DISC
SLIDE DRIVEN
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
DISC ASSEMBLY
TOWARD OUTSIDE
EDGE
4.3.3. DRIVEN DISC ADJUSTMENT
(Continued From Previous Page)
2. Remove driven disc spring from driven disc
assembly. Loosen connector hex nut. See Figure
4.9.
TRANSFER
ROD
OUTSIDE
EDGE
DRIVEN DISC
ASSEMBLY
CONNECTOR
DRIVE
DISC
CONNECTOR
HEX NUT
FIGURE 4.10
DRIVEN DISC
SPRING
CONNECTOR
CLIP
TRANSFER
ROD
CONNECTOR
TRANSFER
ROD
CONNECTOR
HEX NUT
SPEED
CONTROL
ROD
FIGURE 4.9
3. Slide driven disc assembly over to 1/8” from
outside edge of drive disc. Maintaining the 1/8”
measurement, remove any looseness from the
linkage. This can be done by holding the transfer
rod and applying pressure to the left (as viewed
from operators position). Then retighten the
connector hex nut securely. See Figure 4.10. Move
ground speed control to the first speed position,
then back to the sixth speed position. Recheck the
1/8” measurement described previously. Reinstall
driven disc spring to driven disc assembly.
REINSTALLED CLIP
AND TRANSFER ROD
CONNECTOR
CLIP
TRANSFER
ROD
SPEED
CONTROL
ROD
4.3.4. Replacing Rubber Driven Disc
If the rubber is badly chunked or worn it must be
replaced. Install new Driven Disc as follows:
1. Using a small flat blade screwdriver, free the clip
from the transfer rod. Then remove the transfer rod
from the clip and the speed control rod. See Figure
4.11.
FIGURE 4.11
17
Section 4 - REPAIR & ADJUSTMENTS
4.3.5. Replacing Bearing In Driven Disc Assembly
WARNING
IMPORTANT: The bearing, on these machines, is
staked into the thrust plate. The bearing will have to be
driven out with a mallet and a large punch. A new
bearing with four retaining screws will have to be
purchased to replace existing bearing.
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
If the driven disc bearing requires replacement,
remove the driven disc assembly and replace
bearing as follows:
1. Using a small flat blade screwdriver, free the clip
from the transfer rod. Then remove the transfer rod
from the clip and the speed control rod. See Figure
4.11.
2. Using needle nose pliers, unhook the drive
spring and slide the driven disc assembly off the
hex shaft. See Figure 4.12.
3. Remove both snap rings that secure rubber
driven disc hub to thrust plate. See Figure 4.13.
4. Slide the rubber driven disc hub out of the
bearing.
4.3.4. Replacing Rubber Driven Disc
(Continued from previous page)
2. Using needle nose pliers, unhook the drive
spring and slide the driven disc assembly off the
hex shaft. See Figure 4.12.
3. Remove the two snap rings which secure the
rubber driven disc to the driven disc assembly. See
Figure 4.13.
4. Install new rubber driven disc onto driven disc
assembly with retaining rings.
5. Reverse above procedures for reassembly and
installation of driven disc assembly.
5. Drive out existing bearing.
6. Install new bearing and secure to thrust plate
with four retaining screws. Tighten screws securely.
7. Reassemble components in reverse order.
DRIVEN DISC
ASSEMBLY
INSTALL NEW
DRIVEN DISC
SNAP
RINGS
FIGURE 4.13
FIGURE 4.12
18
Section 4 - REPAIR & ADJUSTMENTS
4.4 BELT SERVICE
WARNING
On self-propelled mowers, the engine belt transmits
power from engine to drive disc. The drive disc
powers the poly-v belt, which engages the
transmission that powers the rear wheels. Should
these belts become worn, they could cause slippage,
which would impair mower performance. The
condition of the engine belt and poly-v belt should be
checked after every 25 hours of mower operation.
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
4.3.6. Replacement Of Bearing On Pulley End Of
Hex Shaft
To replace the bearing on the pulley end of the hex
shaft, proceed as follows:
1. Hold the hex shaft with an adjustable wrench
held next to the pulley.
2. Remove the 3/8” hex lock nut, which is located
on the outside of the right wheel bracket. See
Figure 4.14.
4.4.1. Engine Drive Belt Replacement
(Stretch Type Belts)
1. Empty the fuel tank.
2. Note the belt routing in Figure 4.15. There is no
idler pulley on these models to disconnect. See
Figure 4.15.
DRIVE BELT
ENGINE DRIVE
PULLEY
3. Remove holder, O-ring and bearing.
4. Install new bearing.
5. Carefully install new O-ring over the outside of the
new bearing.
6. Install bearing holder and secure with screws.
7. Install 3/8” hex lock nut.
DRIVE DISC
TOP VIEW OF STRETCH TYPE BELT ROUTING
FIGURE 4.15
BALL BEARING
“O” RING
3/8”
LOCK NUT
BALL BEARING
HOLDER
FIGURE 4.14
19
Section 4 - REPAIR & ADJUSTMENTS
PULLEY POSITION
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
DRIVE DISC
SLOT IN END
OF DRIVE DISC
BOLT
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
BUSHING
4.4.1. Engine Drive Belt Replacement
(Stretch Type Belts)
DECK BRACKET
(PARTIALLY SHOWN)
(Continued From Previous Page)
BOLT RETAINER
IMPORTANT: Drain fuel tank before tipping mower.
DO NOT tip machine with carburetor or spark plug down.
Oil from crankcase will saturate the air filter and cause the
engine to be hard to start or not start at all. If
contamination does occur, the air filter will have to be
replaced.
LOCK WASHER
NUT
3. Remove the driven disc.
“Replacing Rubber Driven Disc” for driven disc
assembly removal procedure.
Refer to Section
FIGURE 4.16
4.4.2. Transmission Poly-V Belt Replacement
1. Remove the driven disc. Refer to Section
”Re4placing Rubber Driven Disc“ for procedure.
2. Note the routing of the old belt around the three
pulleys before removing it. See Figure 4.17.
3. Place new Poly-V Belt over end of hex shaft and
onto driven pulley.
4. Tilt mower up on its rear wheels and remove
blade and blade hub. Assistance from another
person may be necessary to hold mower in the tilted
position.
5. Hold the slotted end of the drive disc bolt with a
screwdriver and remove the nut and internal tooth
lock washer. See Figure 4.16.
6. Remove the belt cover located under deck.
7. Lift the drive disc up and remove worn belt.
8. Loop one end of new belt over engine pulley and
insert the other end through slot in deck.
See Figure 4.15.
4. Work belt onto top of idler pulley.
5. Twist belt sideways and pull it upward between
the differential bracket and drive pulley and then
down into the pulley groove. Make sure the Poly-V
Belt is above belt guide. See Figure 4.17.
6. Adjust clutch cable. Refer to Section “Wheel
Drive Control Adjustment:”.
9. Loop the belt around the pulley on the bottom of
the drive disc.
10. Reinstall drive disc and retaining hardware.
IMPORTANT: 1) The square shoulder of the drive
disc bolt must fit into the square hole of the bushing.
2) The square end of bushing must fit into the
bracket slot.
IDLER
DIFFERENTIAL
PULLEY
BRACKET
DRIVE
PULLEY
POLY-V
BELT
11. Reinstall belt cover and tighten bolts securely.
12. Reinstall blade hub and cutter blade.
Recommended torque for blade cap screw is 40 ft. lbs.
HEX SHAFT
DRIVEN
PULLEY
BELT GUIDE
ROUTING OF POLY-V BELT
FIGURE 4.17
20
Section 4 - REPAIR & ADJUSTMENTS
4.5. BATTERY SERVICE
4.5.2. BATTERY SERVICE
1. Remove battery.
2. Place battery in a well ventilated area on a level
surface.
3. Using distilled water, refill cells as required to bring
fluid to proper level.
4. With cell caps removed, connect battery charger to
battery terminals. Red to positive (+) terminal and
black to negative (-) terminal.
5. Slow charge battery at 1 amp for 10 hours.
6. If battery will not accept charge or is partially
charged after 10 hours of charging at 1 amp, replace
with new battery.
4.5.1. NEW BATTERY PREPARATION
1. Remove battery from carton.
2. Place battery in a well ventilated area on a level
non-concrete surface.
3. Remove battery cell caps. Fill cells with electrolyte
to proper level. Filling battery with electrolyte will bring
the battery to 80% charged state.
4. With cell caps removed, connect battery charger to
battery terminals; RED to positive (+) and BLACK to
negative (-) terminal.
IMPORTANT: Never place anything in battery other than
specified electrolyte.
4.5.3. BATTERY STORAGE
5. Slow charge the battery at 1 amp for 2 hours to
bring the battery to full charge.
6. After charging, check level of electrolyte and add
as needed to bring to proper level.
If Walk Behind is to be stored out of season on its rear
bumper, it is recommended the battery be removed,
charged and stored.
1. Remove battery.
7. Reinstall cell caps.
8. Install battery into power unit.
2. Perform battery service.
3. Bring battery to full charge, if required.
4. Store battery in an area away from the Walk
Behind on a wood surface. DO NOT STORE
BATTERY ON A CONCRETE SURFACE.
9. Connect positive (+) cable (red) first, from wiring
harness to the positive terminal (+) on battery using
bolt and nut provided in hardware bag. Connect
negative (-) cable (black) last, to negative terminal (-)
on battery using bolt and nut. Apply a small amount of
grease over terminals to prevent corrosion.
4.5.4. BATTERY TESTING
There are two types of battery tests: Unloaded and
Loaded. The unloaded test is the procedure that will
be discussed. It’s the simplest and most commonly
used. An unloaded test is made on a battery without
discharging current. To perform unloaded testing,
check charge condition using either a hydrometer or
voltmeter.
WARNING
DO NOT over fill battery with electrolyte. Shield the
positive terminal with terminal cover located on battery
harness. This prevents metal from touching the
positive terminal, which could cause sparks. The
electrolyte (acid) produces a highly explosive gas.
Keep all sparks, flame and fire away from area when
charging battery or when handling electrolyte or
battery. Electrolyte (acid) is a highly corrosive liquid.
Wear eye protection. Wash affected areas immediately
after having eye or skin contact with electrolyte (acid).
Battery acid is corrosive. Rinse empty acid containers
with water and mutilate before discarding. If acid is
spilled on battery, bench, or clothing, etc., Flush with
clear water and neutralize with baking soda. Never
attempt to charge battery while installed on the walk
behind. Never use “BOOST” chargers on the battery.
1. Using a voltmeter, voltage readings appear
instantly to show the state of charge. Remember to
hook the positive lead to the battery’s positive
terminal, and the negative lead to the negative
terminal.
2. A hydrometer measures the specific gravity of
each cell. The specific gravity tells the degree of
charge; generally, a specific gravity of about 1.265 to
1.280 indicates full charge. A reading of 1.230 to
1.260 indicates the battery should be charged. The
chart on the next page shows the charge level as
measured by syringe float hydrometer, digital
voltmeter and five ball hydrometer.
4.5.4. BATTERY TESTING
Methods of Checking Battery Condition
State of Charge
100% Charged w/ Sulfate Stop
100% Charged
75% Charged
50% Charged
Syringe Hydrometer
Digital Voltmeter
Five Ball Hydrometer
Five Balls Floating
Four Balls Floating
Three Balls Floating
Two Balls Floating
One Ball Floating
1.280
12.80v
1.265
1.210
12.60v
12.40v
1.160
12.10v
25% Charged
1.120
11.90v
0% Charged
Less than 1.100
Less than 11.80v
Zero Balls Floating
21
TROUBLESHOOTING
PROBLEM
PROBABLE CAUSE
CORRECTIVE ACTION
Engine Will Not Start 1. Fuel tank empty.
Using Recoil Starter 2. Engine needs priming.
3. Spark plug wire disconnected.
1. Fill fuel tank with fresh fuel.
2. Prime. Check Engine Manual for Instructions.
3. Place spark plug wire onto spark plug.
Engine Stalls or Stops 1. Blade control is released or is not being held securely 1. Blade control should be held securely against
After Running
against handle.
handle at all times during operation of mower.
2. Fuel tank empty.
2. Fill with fuel to proper level.
3. Engine air pre-cleaner and or air cleaner dirty.
4. Spark plug defective or gap set improperly.
5. Water, debris or stale fuel in fuel system.
3. Clean free of all debris.
4. Service spark plug.
5. Drain and clean fuel system.
1. Clean or replace filters.
Engine Loses Power 1. Engine air pre-cleaner or air cleaner dirty
2. Spark plug faulty.
2. Service spark plug.
3. Water, debris or stale fuel in fuel system.
3. Drain and clean fuel system.
Excessive Vibration 1. Damaged, out of balance or bent mower blade.
2. Loose blade components.
1. Service mower blade.
2. Service and tighten loose parts.
3. Replace air lifts. Tighten to proper torque.
4. Replace belt.
3. Loose or missing air lift (if equipped).
4. Lumpy or frayed belt
1. Damaged transmission
2. Traction drive belt requires replacement
3. Driven disc slipping
Mower Will Not Move
Loss Of Traction
(Self-Propelled Models)
1. Contact authorized SNAPPER dealer.
2. Replace traction drive belt.
3. Clean or replace driven disc.
1. Cutting height too low or high.
2. Forward ground speed too fast.
3. Terraced cut, side to side.
1. Adjust cutting height.
Cutting Grass
Improperly
3. Move ground speed control to a slower speed.
4. Adjust height of cut with height adjust levers.
5. Adjust height of cut with height adjust levers.
6. Sharpen cutting edges or replace blade.
1. Move ground speed control to a slower speed.
2. Mow when grass is dry.
4. Excessive deck pitch, front to rear.
5. Cutting blade dull or damaged.
1. Forward speed too fast.
Poor Grass Discharge
2. Grass is wet.
3. Excessively worn or damaged blade.
4. Build up of grass clippings and debris under deck.
5. Improper blade installed on deck.
6. Blade installed improperly on deck.
1. Leaking engine case.
3. Service mower blade.
4. Clean deck.
5. Install proper SNAPPER blade.
6. Install blade properly.
Oil Leaking
1. Contact authorized SNAPPER dealer.
2. Check and tighten drain plug.
3. Make sure dip stick or oil filler cap is securely
in place.
22
SERVICE SCHEDULE
ITEM
SERVICE PERFORMED
REF.
Page 7
EACH
USE
5
HRS
25
HRS
50
HRS
100
HRS
EACH
SEASON
Check Oil Level
Engine Oil
X
Initial Oil Change
Periodic Oil Change
Page 12
Page 13
X
X*
Clean Sponge Element
Clean or Replace
Replace
Engine Manual
Engine Manual
Engine Manual
Engine Manual
Pages 13, 19
Air Pre-Cleaner
Air Cleaner
X**
X**
Spark Plug
X
Clean Shroud & Fins
Engine Cooling
System
X**
Check For Wear And
Tension
Check For Wear, Damage Pages 14-15
& Replacement
Clean Debris
Accumulation
Drive Belts
X
X
X
X
Mower Blade
Mower Deck
X
X
Page 7
Check Grease Level
Page 13
Transmission
Grease
X
X
Periodic Grease Check
Page 13
Check for Wear Damage Pages 16-18
& Replacement
Drive Disc
X
*Change oil every 25 hours when operating under heavy load or high temperatures.
**Clean more often under dusty conditions or when air debris is present
4.5
MAINTENANCE/REPLACEMENT PARTS
MAINTENANCE PARTS
Blade Control Cable
3-4608
3-4604
1-9795
1-7168
2-6691
2-6407
1-2354
4-6784
5-7668
4-1855
06138
Clutch Pull Cable (See Parts Manual)
Cutter Blade (Air Lift Compatible)
Cutter Blade (Mulching)
Cutter Blade (Not Air Lift Compatible)
Cutter Blade (Ninja - Quad Edge)
Wheel Drive Pulley to Transmission Pulley Belt
Engine to Drive Disc Belt
Cantilever Drive Tire Assembly
Rubber Drive Tire
Parts Manual for 21” Steel Deck Walk Behind Mower Type ‘M’ Series 18
23
2 YEAR LIMITED WARRANTY
For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through
any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts
found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
For ninety (90) days from purchase date for the original purchaser's commercial, rental, or other non-residential use,
SNAPPER, through any authorized SNAPPER dealer will replace, free of charge, any part or parts found upon
examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for
replacement under this warranty must be paid by the purchaser.
This warranty does not apply to certain transmissions, to engines and their components, and batteries, as these items
are warranted separately. This warranty does not apply to parts that have been damaged by accident, alteration,
abuse, improper lubrication, normal wear, or other cause beyond the control of SNAPPER. This warranty does not
cover any machine or component part that has been altered or modified changing safety, performance, or durability.
Batteries have a one (1) year warranty period with free replacement if required for one (1) year from the original
purchase date. SNAPPER will not be responsible for any installation cost incurred. The battery warranty only covers
original equipment batteries and does not cover damage to the battery or machine caused by neglect or abuse,
destruction by fire, explosion, freezing, overcharging, improper maintenance, or use of improper electrolyte.
There is no other express warranty.
DISCLAIMER OF WARRANTY
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to two (2)
years from purchase date for the original purchaser's residential or other non-commercial use, and ninety (90)
days from purchase for the original purchaser's commercial, rental or other non-residential use, and to the
extent permitted by law, any and all implied warranties are excluded. This is the exclusive remedy. Liabilities
for consequential damages, under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
WARNING: THE USE OF REPLACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE
SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER
ASSOCIATED WITH THE USE OF SUCH PARTS.
IMPORTANT: Please fill out the attached SNAPPER Product Registration Card immediately and mail to:
Snapper’s Product Registration Center, P.O. Box 1379, McDonough, Georgia 30253
24
PRIMARY MAINTENANCE
25
PRIMARY MAINTENANCE
26
PRIMARY MAINTENANCE
27
PRIMARY MAINTENANCE
28
SNAPPER PRODUCT REGISTRATION FORM
IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS
(Complete the following information on your Snapper purchase)
Model Number_____________________________________________________________
Serial Number _____________________________________________________________
Date of Purchase ___________________________________________________________
Retailer____________________________________________________________________
Retailer’s Phone Number____________________________________________________
It is very important that you register your purchase with Snapper to ensure
warranty coverage. Please mail your product registration card to:
Snapper at P.O. Box 777, McDonough, Georgia 30253.
You can contact us at our web site or if you would like to speak with a Customer
Service Representative. Call us at the Snapper Customer Relations Center. For
faster service please have your Serial Number and Model Number available.
Call the Snapper Customer Relations Center at 1-800-935-2967.
29
NOTES
30
NOTES
31
Safety Instructions & Operator’s Manual for
21” STEEL DECK
WALK BEHIND MOWERS (TYPE ‘M’)
SERIES 18
IMPORTANT
Snapper products are built using engines that meet or exceed all applicable emissions requirements on the
date manufactured. The labels on those engines contain very important emissions information and critical
safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine
manual, and on the machine, engine and attachments. If you have any questions about your Snapper
product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper,
McDonough, GA. 30253. Phone: (1-800-935-2967).
WARNING
BATTERY POSTS, TERMINALS AND RELATED ACCESSORIES CONTAIN LEAD AND LEAD COMPOUNDS,
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR
OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING.
WARNING
ENGINE EXHAUST, SOME OF ITS CONSTITUENTS, AND CERTAIN VEHICLE COMPONENTS CONTAIN OR
EMIT CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER OR OTHER
REPRODUCTIVE HARM.
COPYRIGHT © 2004
SNAPPER – A DIVISION OF SIMPLICITY MFG., INC.
ALL RIGHTS RESERVED
MANUAL No. 2-9755 (I.R. 7/29/04)
32
|
Briggs Stratton Lawn Mower 131F User Manual
Bush Hog Lawn Mower RFM 60 User Manual
Dixon Lawn Mower 52 21 KAW 52 HONDA 52 20 KOH 52 25 KOH 60 25 KOH 60 25 B&S User Guide
Husqvarna Lawn Mower YTH220 TWIN User Guide
Land Pride Lawn Mower 309 502M User Guide
Shibaura Lawn Mower SR525 User Guide
Snapper Lawn Mower LT23460 7800207 User Manual
Snapper Lawn Mower PD21357B User Manual
Snapper Lawn Mower R21500T2 User Manual
Woods Equipment Lawn Mower ME2052B User Guide