Havis Shields C VS 0812 CHGR User Manual

INSTALL INSTRUCTIONS  
C-VS-0812-CHGR & C-VS-0812-CHGR-1  
20” VEHICLE SPECIFIC LOW PROFILE CONSOLE  
2006-2007 DODGE CHARGER and MAGNUM  
2008 DODGE CHARGER and MAGNUM  
TOOLS REQUIRED:  
Ratcheting wrench  
Sockets - 7/16”  
Screwdriver set  
T-20 torx bit  
Combo wrench set  
HARDWARE:  
ITEM#  
QTY DESCRIPTION  
PART #  
1
2
3
4
5
6
7a  
7b  
8a  
8b  
9
1
1
1
1
1
1
1
1
1
1
2
1
8
8
8
6
4
2
2
1
8” console housing  
Support bracket for stout console  
12” Low profile console (housing only)  
Frame support bracket  
YAW sensor cover panel  
Rear floor filler panel  
Driver side wire panel - 2006 – 07 Charger  
Driver side trim panel - 2008 Charger  
Passenger side wire panel - 2006 – 07 Charger  
Passenger side trim panels - 2008 Charger  
“L” bracket mounting leg  
Extension floor plate  
¼-20 Hex nut  
¼-20 x ¾” Hex bolt  
¼-20 Serrated nut  
10-32 x ½” Phillips machine screw  
10-32 Keps nut  
#10 Flat washer  
Torx hardware kits  
Mounting hardware kit  
CM000672  
CM001595  
C-SM-1200-H  
CM001593  
CM001638  
CM001642  
CM001598-D  
CM002165  
CM001598-P  
CM002164  
C-B41  
CM93712  
GSM30005  
GSM33001  
GSM30023  
GSM33118  
GSM30028  
GSM31003  
C-HK-1  
10  
C-HK  
View of trak removed  
Remove OEM supplied trak.  
Note: Some hardware is re-used  
in installation of console  
Attach frame support bracket  
(#4) to vehicle using 10/32 x ½”  
phillips machine screws,  
washers, and keps nuts  
Attach frame support bracket  
(#4) to vehicle using 10/32 x ½”  
phillips machine screws,  
Attach support bracket for stout  
console (#2) to vehicle and to frame  
support bracket using OEM hardware  
and #10 x ½” phillips machine screws  
and washers  
Tighten hardware  
washers, and keps nuts  
Note: Due to some slight differences on the OEM floor mount bracket, tabs with mounting hole may  
need to be bent slightly to accommodate the console front support bracket. Bending these tabs can easily  
be done using pliers.  
View of installation to this point  
Note: Be sure OEM wiring is not  
being crushed by mounting  
brackets  
Place console assembly and  
install extension (#10) for “L”  
bracket mounting leg on stout  
Attach “L” bracket mounting  
leg (#9) to rear floor filler panel  
(#6) using ¼-20 x ¾” hex bolts  
console, using OEM hardware.  
and serrated nuts.  
Attach rear floor filler panel (#6)  
to vehicle using OEM hardware  
Attach YAW sensor cover panel  
(#5) to vehicle using front  
driver side hardware from rear  
floor filler panel (#6)  
Attach driver and passenger-  
side wire panels (#7 & 8) to  
frame support bracket using #10  
x ½” phillips machine screws  
and washers.  
View of installed C-VS-0812-CHGR  
Route wiring and install emergency  
controls and accessories  
C-VS-0812-CHGR_INST_12-07  
4

AKG Acoustics CU700 User Manual
Brother MFC 9700 User Manual
Carrier 39LH03 25 User Manual
Cornelius ED2XX 629085101 User Manual
GE ASV12AK User Manual
GE General Electric Air Conditioner ASV14 User Manual
Graco CONTEMPO ISPH015AC User Manual
Haier HW 09LN03 User Manual
Heat Controller Inc Air Conditioner BG 101G User Manual
HP Hewlett Packard Hewlett Packard Barcode Reader HP 44714A User Manual