Operator′s manual
240F 240R 250R
252RX 265RX
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Contents
Note the following before starting:
KEY TO SYMBOLS
•
•
Please read the operator’s manual carefully.
Symbols .......................................................................
CONTENTS
2
Long-term exposure to noise can result in permanent
hearing impairment. So always use approved hearing
protection.
Contents ......................................................................
Note the following before starting: ................................
INTRODUCTION
3
3
WARNING! Under no circumstances may the
design of the machine be modified without
the permission of the manufacturer. Always
use genuine accessories. Non-authorized
modifications and/or accessories can result
in serious personal injury or the death of the
operator or others.
Dear Customer, ............................................................
WHAT IS WHAT?
4
!
What is what on the clearing saw? (240R) ...................
What is what on the clearing saw? (240F)....................
What is what on the clearing saw? (250R) ...................
What is what on the clearing saw? (252RX).................
What is what on the clearing saw? (265RX).................
GENERAL SAFETY PRECAUTIONS
5
6
7
8
9
WARNING! A clearing saw, brushcutter or
trimmer can be dangerous if used
incorrectly or carelessly, and can cause
serious or fatal injury to the operator or
others. It is extremely important that you
read and understand the contents of this
operator’s manual.
Important ...................................................................... 10
Personal protective equipment ..................................... 10
Machine′s safety equipment ........................................ 10
Cutting equipment ........................................................ 13
ASSEMBLY
!
Assembling the handlebar and throttle (240R, 250R)... 16
Fitting the handlebar (240F, 252RX)............................. 16
Husqvarna AB has a policy of continuous product
development and therefore reserves the right to modify the
design and appearance of products without prior notice.
Transport position, handlebar (240R, 240F, 250R,
252RX).......................................................................... 16
Fitting the handlebar (265RX)....................................... 17
Assembling the cutting equipment ............................... 17
Fitting a blade guard, grass blade and grass cutter ..... 17
Fitting the blade guard and saw blade ......................... 18
Fitting the trimmer guard and trimmer head Trimmy SII 18
Fitting other guards and cutting attachments ............... 19
Adjusting the harness and clearing saw ...................... 19
Standard harness ........................................................ 19
Triobalance harness ..................................................... 19
FUEL HANDLING
Fuel safety ................................................................... 21
Fuel .............................................................................. 21
Fuelling ........................................................................ 22
STARTING AND STOPPING
Check before starting ................................................... 23
Starting and stopping ................................................... 24
WORKING TECHNIQUES
General working instructions ....................................... 25
MAINTENANCE
Carburettor ................................................................... 29
Muffler .......................................................................... 29
Cooling system ............................................................ 30
Air filter ......................................................................... 30
Bevel gear .................................................................... 31
Spark plug .................................................................... 31
Maintenance schedule ................................................. 32
TECHNICAL DATA
Technical data .............................................................. 33
EC-declaration of conformity ........................................ 36
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Dear Customer,
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the
Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets.The
location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During the
more than 300 years of beeing, the Husqvarna factory has produced a lot of different products, from wood stoves to modern kitchen
appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first motor driven lawn mowers appeared, followed by chain
saws in 1959, and it is within this area Husqvarna is working today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest priority.
The business concept is to develop, manufacture and market motor driven products for forestry and gardening as well as for
building and construction industry. Husqvarna′s aim is also to be in the front edge according to ergonomics, usability, security and
environmental protection. That is the reason why we have developed many different features to provide our products within these
areas.
We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very long time to
come. The purchase of one of our products gives you access to professional help with repairs and service whenever this may be
necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the address of your nearest service
workshop.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator′s
manual as a valuable document.By following its′ content (using, service, maintenance etc) the life span and the second-hand value
of the machine can be extended. If you will sell this machine, make sure that the buyer will get the operator′s manual.
Good luck on using your Husqvarna machine!
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
8
6
5
3
2
7
9
1
15
4
16
28
22
18
17
1
19
19
4
4
21
26
24
29
27
23
25
What is what on the clearing saw? (240R)
1
2
3
4
5
6
7
8
9
Blade
16 Locking screw (support cup)
17 Support flange
18 Support cup
Grease filler cap
Bevel gear
Cutting attachment guard
Shaft
19 Drive disc
20 Trimmer head
21 Socket spanner
22 Operator′s manual
23 Transport guard
24 Allen key
Handlebar
Throttle control
Stop switch
Throttle lock
10 Support eyes for harness
11 Cylinder cover
12 Starter handle
13 Fuel tank
25 Carburettor screwdriver
26 Locking pin
27 Harness
28 Locking nut
14 Choke control
29 Gearbox grease
30 Air filter
15 Handle adjustment
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
8
5
3
2
7
9
14
15
11
10
13
26
4
12
20
6
16
17
1
18
27
4
21
25
19
23
24
22
What is what on the clearing saw? (240F)
1
2
3
4
5
6
7
8
9
Blade
15 Handle adjustment
Grease filler cap
Bevel gear
16 Locking nut
17 Support flange
18 Drive disc
Cutting attachment guard
Shaft
19 Socket spanner
20 Operator′s manual
21 Transport guard
22 Allen key
Handlebar
Throttle control
Stop switch
Throttle lock
23 Carburettor screwdriver
24 Locking pin
10 Support eyes for harness
11 Cylinder cover
12 Starter handle
13 Fuel tank
25 Harness
26 Air filter
27 Gearbox grease
14 Choke control
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
8
9
3
7
1
22
11
16
6
2
10
12
29
17
19
18
4
5
15
14
13
1
28
20
4
21
25
26
24
27
23
What is what on the clearing saw? (250R)
1
2
3
4
5
6
7
8
9
Blade
16 Handle adjustment
Grease filler cap
Bevel gear
17 Locking screw (support cup)
18 Support flange
19 Support cup
Cutting attachment guard
Shaft
20 Drive disc
Handlebar
21 Socket spanner
22 Operator′s manual
23 Transport guard
24 Allen key
Throttle control
Stop switch
Throttle lock
10 Support eyes for harness
11 Cylinder cover
12 Starter handle
13 Choke control
14 Air filter
25 Carburettor screwdriver
26 Locking pin
27 Harness
28 Gearbox grease
29 Locking nut
15 Fuel tank
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
8
3
1
7
9
21
5
16
11
2
10
12
4
17
6
15
18
14
13
1
27
19
20
4
24
26
25
23
22
What is what on the clearing saw? (252RX)
1
2
3
4
5
6
7
8
9
Blade
15 Fuel tank
Grease filler cap
Bevel gear
16 Handle adjustment
17 Locking nut
Cutting attachment guard
Shaft
18 Support flange
19 Drive disc
Handlebar
20 Socket spanner
21 Operator′s manual
22 Transport guard
23 Allen key
Throttle control
Stop switch
Throttle lock
10 Support eyes for harness
11 Cylinder cover
12 Starter handle
13 Choke control
14 Air filter
24 Carburettor screwdriver
25 Locking pin
26 Harness
27 Gearbox grease
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
8
11
9
15
13
7
3
14
5
1
10
12
16
4
2
6
17
18
1
22
19
4
21
20
26
24
27
25
23
What is what on the clearing saw? (265RX)
1
2
3
4
5
6
7
8
9
Blade
15 Air filter
Grease filler cap
Bevel gear
16 Handle adjustment
17 Locking nut
Cutting attachment guard
Shaft
18 Support flange
19 Drive disc
Handlebar
20 Socket spanner
21 Operator′s manual
22 Transport guard
23 Allen key
Throttle control
Stop switch
Throttle lock
10 Support eyes for harness
11 Cylinder cover
12 Starter handle
13 Fuel tank
24 Carburettor screwdriver
25 Locking pin
26 Harness
27 Gearbox grease
14 Choke control
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
HEARING PROTECTION
Important
Wear hearing protection that provides adequate noise
reduction.
IMPORTANT!
The machine is only designed for trimming grass, grass
clearing and/or forestry clearing.
The only accessories you can operate with this engine unit
are the cutting attachments we recommend in the chapter
on Technical data.
EYE PROTECTION
Always wear approved eye protection. If you use a visor then
you must also wear approved protective goggles. Approved
protective goggles must comply with standard ANSI Z87.1 in
the USA or EN 166 in EU countries.Visors must comply with
standard EN 1731.
Never use the machine if you are tired, if you have drunk
alcohol, or if you are taking medication that could affect your
vision, your judgement or your co-ordination.
Wear personal protective equipment. See instructions
under the heading Personal protective equipment.
Never use a machine that has been modified in any way
from its original specification.
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual.Some maintenance and service measures must be
carried out by trained and qualified specialists. See
instructions under the heading Maintenance.
GLOVES
Gloves should be worn when necessary, e.g., when fitting
cutting attachments.
All covers and guards must be fitted before starting. Make
sure the spark plug cap and HT lead are not damaged.
Otherwise you could get an electric shock.
The machine operator must ensure that no people or
animals come closer than 15 metres while working. When
several operators are working in the same area the safety
distance should be at least twice the tree height and no less
than 15 metres.
BOOTS
Wear sturdy, non-slip boots.
Personal protective equipment
IMPORTANT!
A clearing saw, brushcutter or trimmer can be dangerous if
used incorrectly or carelessly, and can cause serious or
fatal injury to the operator or others. It is extremely
important that you read and understand the contents of this
operator’s manual.
CLOTHING
Wear clothes made of a strong fabric and avoid loose clothing
that can catch on twigs and branches. Always wear heavy,
long pants. Do not wear jewellery, shorts sandals or go
barefoot. Secure hair so it is above shoulder level.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen. Ask
your dealer for help in choosing the right equipment.
FIRST AID KIT
Always have a first aid kit nearby.
WARNING! Listen out for warning signals or
shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
!
′
Machine s safety equipment
HELMET
This section describes the machine′s safety equipment, its
purpose, and how checks and maintenance should be carried
out to ensure that it operates correctly. See the ”What is
what?” section to locate where this equipment is positioned
on your machine.
A helmet should be worn if the trees being cleared are taller
than 2 m.
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
The life span of the machine can be reduced and the risk of
Check that the throttle control and throttle lock move freely
and that the return springs work properly.
accidents can increase if machine maintenance is not carried
out correctly and if service and/or repairs are not carried out
professionally. If you need further information please contact
your nearest service workshop.
IMPORTANT!
All servicing and repair work on the machine requires
special training. This is especially true of the machine′s
safety equipment. If your machine fails any of the checks
described below you must contact your service agent.
When you buy any of our products we guarantee the
availability of professional repairs and service. If the retailer
who sells your machine is not a servicing dealer, ask him for
the address of your nearest service agent.
See instructions under the heading Start. Start the machine
and apply full throttle. Release the throttle and check that the
cutting attachment stops and remains at a standstill. If the
cutting attachment rotates with the throttle in the idle position
then the carburettor idle setting must be checked. See
instructions under the heading Maintenance.
WARNING! Never use a machine with faulty
safety equipment.The machine’s safety
equipment must be checked and maintained
as described in this section. If your machine
fails any of these checks contact your
service agent to get it repaired.
!
Throttle lock
The throttle lock is designed to prevent accidental operation
of the throttle control. When you press the lock (A) (i.e. when
you grasp the handle) it releases the throttle control (B).
When you release the handle the throttle control and the
throttle lock both move back to their original positions. This
movement is controlled by two independent return springs.
This arrangement means that the throttle control is
automatically locked at the idle setting.
Stop switch
Use the stop switch to switch off the engine.
Start the engine and make sure the engine stops when you
move the stop switch to the stop setting.
Cutting attachment guard
Make sure the throttle control is locked at the idle setting
when the throttle lock is released.
This guard is intended to prevent loose objects from being
thrown towards the operator. The guard also protects the
operator from accidental contact with the cutting attachment.
Press the throttle lock and make sure it returns to its original
position when you release it.
Check that the guard is undamaged and not cracked.Replace
the guard if it has been exposed to impact or is cracked.
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Always use the recommended guard for the cutting
attachment you are using. See chapter on Technical data.
Quick release
There is an easily accessible, quick release fitted at the front
as a safety precaution in case the engine catches fire, or in
any other situation that requires you to free yourself from the
machine and harness. See instructions under the heading
Adjusting the harness and clearing saw.
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
!
Certain harnesses also have a quick release fitted to the
support hook.
Vibration damping system
Your machine is equipped with a vibration damping system
that is designed to minimize vibration and make operation
easier.
Check that the harness straps are correctly positioned. Once
the harness and machine have been adjusted, check that the
harness quick release works correctly.
Muffler
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user.
Use of incorrectly wound cord or an incorrect cutting
attachment increases the level of vibration. See instructions
under the heading Cutting equipment.
A muffler fitted with a catalytic converter is also designed to
reduce harmful exhaust gases.
The machine′s vibration damping system reduces the transfer
of vibration between the engine unit/cutting equipment and
the machine′s handle unit.
In countries that have a warm and dry climate there is a
significant risk of fire. We therefore fit certain mufflers with a
spark arrestor mesh. Check whether the muffler on your
machine is fitted with this kind of mesh.
Regularly check the vibration damping units for cracks or
deformation. Check that the vibration damping element is
undamaged and securely attached.
WARNING! Overexposure to vibration can
lead to circulatory damage or nerve damage
in people who have impaired circulation.
!
For mufflers it is very important that you follow the instructions
on checking, maintaining and servicing your machine. See
instructions under the heading Checking, maintaining and
servicing the machine’s safety equipment.
Contact your doctor if you experience
symptoms of overexposure to vibration.
Such symptoms include numbness, loss of
feeling, tingling, pricking, pain, loss of
strength, changes in skin colour or
condition.These symptoms normally appear
in the fingers, hands or wrists.The risk
increases at low temperatures.
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to the
machine.
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
If the muffler on your machine is fitted with a spark arrestor
The nylon lining inside the locking nut must not be so worn
that you can turn it by hand. The lining should offer a
resistance of at least 1.5 Nm. The nut should be replaced
after it has been put on approx. 10 times.
mesh this must be cleaned regularly. A blocked mesh will
cause the engine to overheat and may lead to serious
damage.
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
•
•
•
Reduce the risk of blade thrust.
Obtain maximum cutting performance.
Extend the life of cutting equipment.
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.This
also applies at idle speed. Contact can result
in burns to the skin. Remember the risk of
fire!
!
IMPORTANT!
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
WARNING! The inside of the muffler contain
chemicals that may be carcinogenic. Avoid
contact with these elements in the event of a
damaged muffler.
Refer to the instructions for the cutting attachment to check
the correct way to load the cord and the correct cord
diameter.
!
Keep the teeth of the blade correctly sharpened! Follow our
recommendations. Also refer to the instructions on the
blade packaging.
WARNING! Bear in mind that:
Maintain the correct blade setting! Follow our instructions
and use the recommended file gauge.
!
Engine exhaust fumes contain carbon
monoxide, which can cause carbon
monoxide poisoning. For this reason you
should not start or run the machine indoors,
or anywhere that is poorly ventilated.
WARNING! Always stop the engine before
doing any work on the cutting attachment.
This continues to rotate even after the
!
The exhaust fumes from the engine are hot
and may contain sparks which can start a
fire. Never start the machine indoors or near
combustible material!
throttle has been released. Ensure that the
cutting attachment has stopped completely
and disconnect the HT lead from the spark
plug before you start to work on it.
Locking nut
WARNING! Using an incorrect cutting
attachment or an incorrectly sharpened
blade increases the risk of kickback.
!
A locking nut is used to secure some types of cutting
attachment.
Cutting equipment
When fitting, tighten the nut in the opposite direction to the
direction of rotation of the cutting attachment. To remove it,
undo the nut in the same direction as the cutting attachment
rotates. (CAUTION! The nut has a left-hand thread.)
Saw blades are intended for cutting fibrous types of wood.
When loosening and tightening the saw blade nut, there is a
risk of injury from the teeth of the saw blade.You should
therefore always ensure that your hand is shielded by the
blade guard when doing this. Always use a socket spanner
with a shaft that is long enough to allow this.The arrow in the
diagram shows the area where you should operate the socket
spanner when loosening or tightening the nut.
Grass blades and grass cutters are intended for cutting
coarse grass.
A trimmer head is intended for trimming grass.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
General rules
Sharpening grass cutters and grass
blades
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
•
•
See the cutting attachment packaging for correct
sharpening instructions. Sharpen blades and cutters
using a single-cut flat file.
Sharpen all edges equally to maintain the balance of the
blade.
Keep the teeth of the blade correctly sharpened! Follow our
instructions and use the recommended file gauge. An
incorrectly sharpened or damaged blade increases the risk of
accidents.
WARNING! Always discard a blade that is
bent, twisted, cracked, broken or damaged
in any other way. Never attempt to straighten
a twisted blade so that it can be reused. Only
use original blades of the specified type.
!
Keep the correct setting on the saw blade! Follow our
instructions and use the recommended setting tool. An
incorrectly set saw blade increases the risk of jamming and
kickback, and damage to the saw blade.
Sharpening the saw blade
•
See the cutting attachment packaging for correct
sharpening instructions.
A correctly sharpened blade is essential for working efficiently
and to avoid unnecessary wear to the blade and clearing saw.
Check the cutting attachment for damage or cracks. A
damaged cutting attachment should always be replaced.
•
Make sure that the blade is well supported when you file
it. Use a 5.5 mm round file with a file holder.
•
The filing angle is 15°. File alternate teeth to the right and
those in between to the left. If the blade has been heavily
pitted by stones it may be necessary to dress the top
edges of the teeth with a flat file, in exceptional cases. If
14 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
so, this should be done before filing with a round file. The
top edges must be filed down by the same amount for all
the teeth.
Adjust the blade setting. This should be 1 mm.
Trimmer head
IMPORTANT!
Always ensure the trimmer cord is wound tightly and evenly
around the drum, otherwise the machine will generate
harmful vibration.
•
Only use the recommended trimmer heads and trimmer
cords.These have been tested by the manufacturer to suit
a particular engine size.This is especially important when
a fully automatic trimmer head is used. Only use the
recommended cutting attachment. See the chapter on
Technical data.
•
•
Smaller machines generally require small trimmer heads
and vice versa. This is because when clearing using a
cord the engine must throw out the cord radially from the
trimmer head and overcome the resistance of the grass
being cleared.
The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of the
same diameter.
•
•
Make sure that the cutter on the trimmer guard is intact.
This is used to cut the cord to the correct length.
To increase the life of the cord it can be soaked in water
for a couple of days.This will make the line tougher so that
it lasts longer.
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembling the handlebar and
throttle
Fitting the handlebar
(240F, 252RX)
(240R, 250R)
•
•
Unscrew the knob from the handlebar mounting.
Position the handlebar as shown. Fit the mounting
components and tighten the knob lightly.
•
•
Remove the screw at the rear of the throttle handle.
Slide the throttle handle onto the right side of the
handlebar, (see diagram).
•
Fit the right handle to the handlebar using the screw,
washer, sleeve and nut as shown. Tighten.
•
Align the screw hole in the throttle handle with the hole in
the handlebar.
•
•
Refit the screw in the hole in the rear of the throttle handle.
Screw the screw through the handle and handlebar.
Tighten it.
•
•
Unscrew the knob from the handlebar mounting.
•
Put on the harness and hang the machine from the
support hook. Now make a final adjustment so that the
machine is in a comfortable working position when it
hangs from the harness.
Position the handlebar as shown. Fit the mounting
components and tighten the knob lightly.
Tighten the knob.
•
Put on the harness and hang the machine from the
support hook. Now make a final adjustment so that the
machine is in a comfortable working position when it
hangs from the harness.
Transport position, handlebar
(240R, 240F, 250R, 252RX)
•
•
•
The handlebar can easily be turned to fit along the shaft
for easier transportation and storage.
Loosen the knob.Turn the handlebar clockwise so that the
throttle handle rests against the engine.
Now twist the handlebar around the shaft. Tighten the
knob.
•
Tighten the knob.
•
Fit the transport guard to the cutting attachment.
16 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Fitting the handlebar
Assembling the cutting equipment
(265RX)
WARNING!
!
When fitting the cutting attachment it is
extremely important that the raised section
on the drive disc/support flange engages
correctly in the centre hole of the cutting
attachment. If the cutting attachment is fitted
incorrectly it can result in serious and/or
fatal personal injury.
•
•
•
Fit the left handlebar in the handlebar mounting.
Fit the right handle to the handlebar.
Adjust roughly and tighten the screws slightly.
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
•
Now make a final adjustment, with the machine hanging
from the harness, to obtain the most comfortable working
position. Tighten the screws.
!
IMPORTANT! If a saw blade or grass blade are to be used
the machine must be equipped with the correct handlebar,
blade guard and harness.
Fitting a blade guard, grass blade
and grass cutter
•
Make the final adjustment to the right handle and lock it in
the most comfortable position.
Adjusting the throttle trigger
•
The blade guard (A) is fitted using 4 screws (L) and the
support plate (M) as shown.
The throttle trigger can be adjusted to give the best working
position. This is done using the Allen screws by the right
handle.
CAUTION! Always use the recommended guard for the
cutting attachment you are using. See chapter on
Technical data.
•
•
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
•
•
Insert the locking pin (C) in the hole to lock the shaft.
Place the blade (D) on the output shaft.
N
E
F
D
M
B
L
C
A
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
•
•
Fit the support flange (F) on the output shaft. Make sure
that the blade is centered by fitting it to the guide on the
support flange.
To tighten the nut, turn the spanner in the opposite
direction to the direction of rotation (Caution! left-hand
thread).
G
F
Screw the support cup (E) onto the output shaft threads
(CAUTION! Left-hand thread). Tighten to a torque of 35-
50 Nm (3.5-5.0 kpm). Use the socket spanner in the tool
kit. Note that the locking pin (C) must remain inside the
gear housing to lock the drive disk. Hold the shaft of the
socket spanner as close to the blade guard/combination
guard as possible.
D
B
C
When loosening and tightening the saw blade nut, there is a
risk of injury from the teeth of the saw blade.You should
therefore always ensure that your hand is shielded by the
blade guard when doing this. Always use a socket spanner
with a shaft that is long enough to allow this.The arrow in the
diagram shows the area where you should operate the socket
spanner when loosening or tightening the nut.
WARNING! Tighten the lock screw (N) in the
center hole of the support cup.Tighten to a
torque of 35-50 Nm (3.5-5.0 kpm), CAUTION!
!
Left-hand thread. If the lock screw is not
fitted in the support cup, there is a risk that
the support cup will come unscrewed.This
means that the blade will also come loose,
which could result in serious or fatal injury
to the operator or others.
Fitting the trimmer guard and
trimmer head Trimmy SII
Fitting the blade guard and saw
blade
•
Fit the correct trimmer guard (A) for use with the trimmer
head. Secure the trimmer guard using the 4 screws (L)
and the support plate (M) as shown.
•
The blade guard (A) is fitted using 4 screws (L) as shown.
CAUTION!
•
•
Fit the drive disc (B) on the output shaft.
Always use the recommended guard for the cutting
attachment you are using. See chapter on Technical data.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
L
•
Insert the locking pin (C) in the hole to lock the shaft.
A
L
B
A
C
M
•
•
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
•
•
Screw on the trimmer head/plastic blades (H) in the
opposite direction to the direction of rotation.
•
•
Insert the locking pin (C) in the hole to lock the shaft.
Tighten the trimmer head to a torque of 35-50 Nm.
Place the blade (D) and support flange (F) on the output
shaft.
H
•
Fit the nut (G). Tighten the nut to a torque of 35-50 Nm.
Use the socket spanner in the tool kit. Grasp the handle of
the spanner as close to the blade guard/combination
guard as possible.
•
To dismantle, follow the instructions in the reverse order.
18 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Spreading the load on your shoulders
Fitting other guards and cutting
attachments
A well-adjusted harness and machine makes work much
easier. Adjust the harness for the best working position.
Tension the side straps so that the weight is evenly distributed
across both shoulders.
Fit the trimmer guard/combination guard (A) intended for use
with the trimmer head/plastic blades. Secure the trimmer
guard using the 4 screws (L) and the support plate (M) as
shown.
•
•
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
•
Insert the locking pin (C) in the hole to lock the shaft.
Correct height
A
L
1
Forestry clearing
B
The machine should be supported in a harness when
forestry clearing so that the cutting equipment is angled
slightly forwards in relation to the ground. Adjust the
height using the strap on the harness for the support
hook.
C
M
•
Screw on the trimmer head/plastic blades (H) in the
opposite direction to the direction of rotation.
H
H
2
Grass clearing
•
To dismantle, follow the instructions in the reverse order.
The machine should be supported in a harness when
grass clearing so that the cutting equipment is parallel to
the ground.
Adjusting the harness and clearing
saw
WARNING! When using a clearing saw it
must always be hooked securely to the
harness. Otherwise you will be unable to
control the clearing saw safely and this can
result in injury to yourself or others. Never
use a harness with a defective quick release.
!
Standard harness
Triobalance harness
Safety release
Push down the red release lever to release the machine from
the harness.
Safety release
At the front is an easily accessible, quick release. Use this if
the engine catches fire or in any other emergency situation
that requires you to free yourself from the machine and
harness.
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Adjusting the harness
Correct balance
1
Tighten the hip strap so that it sits securely.
1
Forestry clearing
The machine is balanced by moving the support ring on
the machine forwards or backwards. On some models the
support ring is fixed, however, this will then have a number
of holes for the support hook. The machine is correctly
balanced when it freely hangs horizontally from the
support hook. In this way the risk of hitting stones is
reduced if you need to release the handlebar.
2
Tighten the chest strap under your left arm so that it fits
closely around your body.
3
Adjust the shoulder strap to distribute the load evenly
across your shoulders. Press downwards on the
suspension hook to load the harness.
2
Grass clearing
Let the blade balance at a comfortable cutting height, i.e.
close to the ground.
4
Adjust the height of the suspension hook as described in
the instructions for the standard harness. (Forestry
clearing)
5
6
If you need to lower the suspension hook, for trimming for
example, move the suspension strap (A) to the lower
mounting point on the backplate.
The elastic strap (B) can be tightened to transfer more
load from the shoulder straps to the hip strap.
20 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Petrol
Fuel safety
Never start the machine:
1
2
If you have spilt fuel on it. Wipe off the spillage and allow
remaining fuel to evaporate.
CAUTION! Always use a good quality petrol/oil mixture (at
least 90 octane). If your machine is equipped with a catalytic
converter (see chapter on Technical data) always use a good
quality unleaded petrol/oil mixture. Leaded petrol will destroy
the catalytic converter and it will no longer serve its purpose.
If you have spilt fuel on yourself or your clothes, change
your clothes.Wash any part of your body that has come in
contact with fuel. Use soap and water.
3
If the machine is leaking fuel. Check regularly for leaks
from the fuel cap and fuel lines.
Use low-emission petrol, also known as alkylate petrol, if it is
available.
Transport and storage
•
Store and transport the machine and fuel so that there is
no risk of any leakage or fumes coming into contact with
sparks or naked flames, for example, from electrical
machinery, electric motors, electrical relays/switches or
boilers.
•
•
The lowest octane recommended is 90. If you run the
engine on a lower octane than 90 it can result in knocking.
This gives rise to a high engine temperature, which can
result in serious engine damage.
•
•
When storing and transporting fuel always use approved
containers intended for this purpose.
When storing the machine for long periods the fuel tank
must be emptied. Contact your local petrol station to find
out where to dispose of excess fuel.
When working at continuous high revs a higher octane
rating is recommended.
•
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
Two-stroke oil
The transport guard must always be fitted to the cutting
attachment when the machine is being transported or in
storage.
•
For best results and performance use HUSQVARNA two-
stroke oil, which is specially formulated for our two-stroke
engines. Mixture 1:50 (2%).
•
If HUSQVARNA two-stroke oil is not available, you may
use another two-stroke oil of good quality that is intended
for air cooled engines.Contact your dealer when selecting
an oil. Mixing ratio 1:33 (3%).
WARNING! Take care when handling fuel.
Bear in mind the risk of fire, explosion and
inhaling fumes.
!
•
•
Never use two-stroke oil intended for water-cooled
outboard engines, sometimes referred to as outboard oil.
Fuel
Never use oil intended for four-stroke engines.
CAUTION!The machine is equipped with a two-stroke engine
and must always been run using a mixture of petrol and two-
stroke engine oil. It is important to accurately measure the
amount of oil to be mixed to ensure that the correct mixture is
obtained. When mixing small amounts of fuel, even small
inaccuracies can drastically affect the ratio of the mixture.
Two-stroke oil, litre
Petrol, litre
2% (1:50)
3% (1:33)
5
0,10
0,15
10
15
20
0,20
0,30
0,30
0,45
WARNING! Fuel and fuel fumes are highly
inflammable and can cause serious injury
when inhaled or allowed to come in contact
with the skin. For this reason observe
caution when handling fuel and make sure
there is adequate ventilation.
0,40
0,60
!
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Mixing
Fuelling
•
Always mix the petrol and oil in a clean container intended
for fuel.
•
Always start by filling half the amount of the petrol to be
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of petrol.
WARNING!Taking the following precautions,
will lessen the risk of fire:
•
Mix (shake) the fuel mixture thoroughly before filling the
machine’s fuel tank.
!
Do not smoke or place hot objects near fuel.
Always shut off the engine before refuelling.
Always stop the engine and let it cool for a
few minutes before refuelling.
When refuelling, open the fuel cap slowly so
that any excess pressure is released gently.
Tighten the fuel cap carefully after refuelling.
Always move the machine away from the
refuelling area before starting.
•
•
Clean the area around the fuel cap. Contamination in the
tank can cause operating problems.
•
•
Do not mix more than one month’s supply of fuel at a time.
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Ensure that the fuel is well mixed by shaking the container
before filling the tank.
WARNING! The catalytic converter muffler
gets very hot during and after use.This also
applies during idling. Be aware of the fire
hazard, especially when working near
flammable substances and/or vapours.
!
22 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
•
Ensure the locking nut has not lost its captive force. The
Check before starting
nut lock should have a locking force of at least 1.5 Nm.
The tightening torque of the locking nut should be 35-50
Nm.
WARNING! When the engine is started with
the choke in either the choke or start throttle
positions the cutting attachment will start to
rotate immediately.
!
•
Check that the blade guard is not damaged or cracked.
Replace the blade guard if it is exposed to impact or is
cracked.
•
•
Never start the machine indoors. Exhaust fumes can be
dangerous if inhaled.
Observe your surroundings and make sure that there is no
risk of people or animals coming into contact with the
cutting equipment.
•
Place the machine on the ground, ensure the cutting
attachment is clear of twigs and stones. Hold the body of
the machine on the ground using your left hand
•
Check that the trimmer head and trimmer guard are not
damaged or cracked. Replace the trimmer head or
trimmer guard if they have been exposed to impact or are
cracked.
(CAUTION! Not with your foot). Then grip the starter
handle with your right hand and pull the starter cord.
For safety reasons follow these recommendations!
•
Check the blade to ensure that no cracks have formed at
the bottom of the teeth or by the centre hole. The most
common reason why cracks are formed is that sharp
corners have been formed at the bottom of the teeth while
sharpening or that the blade has been used with dull
teeth. Discard a blade if cracks are found.
•
Never use the machine without a guard nor with a
defective guard.
WARNING! The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come loose
and cause personal injury.
!
Always move the machine away from the
refuelling area before starting. Place the
machine on a flat surface. Ensure the cutting
attachment cannot come into contact with
any object.
Make sure no unauthorised persons are in
the working area, otherwise there is a risk of
serious personal injury.The safety distance
is 15 metres.
•
Check that the support flange is not cracked due to fatigue
or due to being tightened too much. Discard the support
flange if it is cracked.
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
Starting
Starting and stopping
Hold the body of the machine on the ground using your left
hand (CAUTION! Not with your foot!). Grip the starter handle,
slowly pull out the cord with your right hand until you feel
some resistance (the starter pawls grip), now quickly and
powerfully pull the cord.Never twist the starter cord around
your hand.
Cold engine
Ignition: Set the stop switch to the start position.
Choke: Set the choke control in the choke position.
Reset the choke control as soon as the engine fires and
repeat until the engine starts. The throttle will automatically
disengage from the start setting when you apply more
throttle.
CAUTION! Do not pull the starter cord all the way out and do
not let go of the starter handle when the cord is fully extended.
This can damage the machine.
Warm engine
Use the same starting procedure as for a cold engine but
without setting the choke control in the choke position.Set the
throttle to the start position by moving the choke control to the
choke position and then returning it to its original position.
Stopping
Stop the engine by switching off the ignition.
24 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
5
Switch off the engine before moving to another area. Fit
the transport guard before carrying or transporting the
equipment any distance.
General working instructions
IMPORTANT!
6
Never put the machine down with the engine running
unless you have it in clear sight.
This section describes the basic safety precautions for
working with clearing saws and trimmers.
The ABC of clearing
If you encounter a situation where you are uncertain how to
proceed you should ask an expert. Contact your dealer or
your service workshop.
•
•
•
•
•
•
•
•
Always use the correct equipment.
Make sure the equipment is well adjusted.
Follow the safety precautions.
Avoid all usage which you consider to be beyond your
capability.
Organise your work carefully.
You must understand the difference between forestry
clearing, grass clearing and grass trimming before use.
Always use full throttle when starting to cut with the blade.
Always use sharp blades.
Basic safety rules
Avoid stones.
Control the felling direction (take advantage of the wind).
1
•
Look around you:
WARNING! Neither the operator of the
machine nor anyone else may attempt to
remove the cut material while the engine is
running or the cutting equipment is rotating,
as this can result in serious injury.
To ensure that people, animals or other things cannot
affect your control of the machine.
!
•
To ensure that people, animals, etc., do not come into
contact with the cutting attachment or loose objects that
are thrown out by the cutting attachment.
Stop the engine and cutting equipment
before you remove material that has wound
around the blade shaft as otherwise there is
a risk of injury.The bevel gear can get hot
during use and may remain so for a while
afterwards.You could get burnt if you touch
it.
•
CAUTION! Do not use the machine unless you are able to
call for help in the event of an accident.
2
Do not use the machine in bad weather, such as dense
fog, heavy rain, strong wind, intense cold, etc. Working in
bad weather is tiring and often brings added risks, such as
icy ground, unpredictable felling direction, etc.
3
Make sure you can move and stand safely.Check the area
around you for possible obstacles (roots, rocks, branches,
ditches, etc.) in case you have to move suddenly. Take
great care when working on sloping ground.
WARNING! Watch out for thrown objects.
Always wear approved eye protection. Never
lean over the cutting attachment guard.
Stones, rubbish, etc. can be thrown up into
the eyes causing blindness or serious injury.
!
Keep unauthorised persons at a distance.
Children, animals, onlookers and helpers
should be kept outside the safety zone of 15
m. Stop the machine immediately if anyone
approaches. Never swing the machine
around without first checking behind you to
make sure no-one is within the safety zone.
4
Take great care when cutting a tree that is in tension. A
tree that is in tension may spring back to its normal
position before or after being cut. If you position yourself
incorrectly or make the cut in the wrong place the tree may
hit you or the machine and cause you to lose control. Both
situations can cause serious personal injury.
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Working methods
Forestry clearing using a saw blade
WARNING! Avoid cutting with the area of the
blade between the 12 o’clock and 3 o’clock
positions. Because of the speed of rotation
of the blade kickback can occur if you
attempt to cut thick stems with this area of
the blade.
!
•
The risk of kickback increases with increasing stem size.
You should therefore avoid cutting with the area of the
blade between 12 o’clock and 3 o’clock.
•
Before you start clearing, check the clearing area, the
type of terrain, the slope of the ground, whether there are
stones, hollows etc.
•
•
Start at whichever end of the area is easiest, and clear an
open space from which to work.
•
To fell to the left, the bottom of the tree should be pushed
to the right. Tilt the blade and bring it diagonally down to
the right, exerting firm pressure. At the same time push
the stem using the blade guard. Cut with the area of the
blade between 3 o’clock and 5 o’clock. Apply full throttle
before advancing the blade.
Work systematically to and fro across the area, clearing a
width of around 4-5 m on each pass. This exploits the full
reach of the machine in both directions and gives the
operator a convenient and varied working area to work in.
•
•
Clear a strip around 75 m long. Move your fuel can as
work progresses.
•
To fell to the right, the bottom of the tree should be pushed
to the left. Tilt the blade and bring it diagonally up to the
right. Cut with the area of the blade between 3 o’clock and
5 o’clock so that the direction of rotation of the blade
pushes the bottom of the tree to the left.
On sloping ground you should work along the slope. It is
much easier to work along a slope than it is to work up and
down it.
•
You should plan the strip so that you avoid going over
ditches or other obstacles on the ground.You should also
orient the strip to take advantage of wind conditions, so
that cleared stems fall in the cleared area of the stand.
•
To fell a tree forwards, the bottom of the tree should be
pulled backwards. Pull the blade backwards with a quick,
firm movement.
•
Large stems must be cut from two sides. First determine
which direction the stem will fall. Make the first cut on the
felling side. Then finish cutting the stem from the other
26 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
side. Adjust the cutting pressure to match the size of the
stem and the hardness of the wood. Small stems require
more pressure, while large stems require less pressure.
Grass clearing using a grass blade
•
Grass blades and grass cutters must not be used on
woody stems.
•
•
A grass blade is used for all types of tall or coarse grass.
The grass is cut down with a sideways, swinging
movement, where the movement from right-to-left is the
clearing stroke and the movement from left-to-right is the
return stroke. Let the left-hand side of the blade (between
8 and 12 o’clock) do the cutting.
•
•
If the blade is angled to the left when clearing grass, the
grass will collect in a line, which makes it easier to collect,
e.g. by raking.
•
•
If the stems are tightly packed, adapt your walking pace to
suit.
If the blade jams in a stem, never jerk the machine free. If
you do this the blade, bevel gear, shaft or handlebar may
be damaged. Release the handles, grip the shaft with
both hands and gently pull the machine free.
Try to work rhythmically. Stand firmly with your feet apart.
Move forward after the return stroke and stand firmly
again.
•
•
Let the support cup rest lightly against the ground. It is
used to protect the blade from hitting the ground.
Brush cutting with a saw blade
Reduce the risk of material wrapping around the blade by
following these instructions:
1
2
Always work at full throttle.
•
Thin stems and brush are mown down. Work with a
sawing movement, swinging sideways.
Avoid the previously cut material during the return
stroke.
•
•
Try to cut several stems in a single sawing movement.
•
Stop the engine, unclip the harness and place the
machine on the ground before you start to collect the cut
material.
With groups of hardwood stems, first clear around the
group. Start by cutting the stems high up around the
outside of the group to avoid jamming.Then cut the stems
to the required height. Now try to reach in with the blade
and cut from the centre of the group. If it is still difficult to
gain access, cut the stems high up and let them fall. This
will reduce the risk of jamming.
English – 27
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Cutting
Grass trimming with a trimmer head
•
The trimmer is ideal for cutting grass that is difficult to
reach using a normal lawn mower. Keep the cord parallel
to the ground when cutting. Avoid pressing the trimmer
head against the ground as this can ruin the lawn and
damage the tool.
Trimming
•
Hold the trimmer head just above the ground at an angle.
It is the end of the cord that does the work. Let the cord
work at its own pace. Never press the cord into the area
to be cut.
•
Do not allow the trimmer head to constantly come into
contact with the ground during normal cutting. Constant
contact of this type can cause damage and wear to the
trimmer head.
•
•
The cord can easily remove grass and weeds up against
walls, fences, trees and borders, however it can also
damage sensitive bark on trees and bushes, and damage
fence posts.
Sweeping
•
The fan effect of the rotating cord can be used for quick
and easy clearing up. Hold the cord parallel to and above
the area to be swept and move the tool to and fro.
Reduce the risk of damaging plants by shortening the
cord to 10-12 cm and reducing the engine speed.
Clearing
•
The clearing technique removes all unwanted vegetation.
Keep the trimmer head just above the ground and tilt it.Let
the end of the cord strike the ground around trees, posts,
statues and the like. CAUTION! This technique increases
the wear on the cord.
•
When cutting and sweeping you should use full throttle to
obtain the best results.
•
•
The cord wears quicker and must be fed forward more
often when working against stones, brick, concrete, metal
fences, etc., than when coming into contact with trees and
wooden fences.
When trimming and clearing you should use less than full
throttle so that the cord lasts longer and to reduce the
wear on the trimmer head.
28 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Basic setting
Carburettor
•
The basic carburettor settings are adjusted during testing
at the factory. The basic setting is richer than the optimal
setting and should be maintained for the first few hours the
machine is in use. The carburettor should then be finely
adjusted. Fine adjustment should be carried out by a
skilled technician.
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions. After the engine has used 8-10 tanks of fuel the
engine will be run-in.To ensure that it continues to run at peak
performance and to minimise harmful exhaust emissions
after the running-in period, ask your dealer/service workshop
(who will have a rev counter at their disposal) to adjust your
carburettor.
The basic setting can vary between: H = 1 - 1 1/4 turns
and L = 1 - 1 1/4 turns.
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
Function
240R, 240F, 250R, 252RX:
Rec. idle speed 2700 rpm
265RX:
•
The carburettor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the carburettor.
The air/fuel mixture is adjustable. Correct adjustment is
essential to get the best performance from the machine.
Rec. idle speed 2250 rpm
•
•
Adjusting the carburettor means that the engine is
adapted to local operating conditions, e.g. climate,
altitude, petrol and the type of 2-stroke oil.
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
!
The carburettor has three adjustment controls:
L = Low speed jet
H = High speed jet
CAUTION! The machine should only be run for short periods
at its highest speed. For optimum adjustment of the
carburettor, contact a qualified dealer/service workshop that
has a revolution counter at their disposal.
T = Idle adjustment screw
Recommended max. speed: See theTechnical data section.
During the running-in period (8-10 tanks of fuel) the maximum
speed should be set 600-700 rpm below the recommended
maximum speed (= open the high speed jet H a further 1/8
turn).
•
The L and H-jets are used to adjust the supply of fuel to
match the rate that air is admitted, which is controlled with
the throttle. If they are screwed clockwise the air/fuel ratio
becomes leaner (less fuel) and if they are turned anti-
clockwise the ratio becomes richer (more fuel). A lean
mixture gives a higher engine speed and a rich mixture
gives a lower engine speed.
Muffler
CAUTION! Some mufflers are fitted with a catalytic converter.
See chapter on Technical data to see whether your machine
is fitted with a catalytic converter.
•
The T-screw regulates the throttle setting at idle speed. If
the T-screw is turned clockwise this gives a higher idle
speed; turning it anti-clockwise gives a lower idle speed.
The muffler is designed to reduce the noise level and to direct
the exhaust gases away from the operator. The exhaust
gases are hot and can contain sparks, which may cause fire
if directed against dry and combustible material. Some
mufflers are equipped with a special spark arrestor mesh. If
your machine has this type of muffler, you should clean the
mesh at least once a week. This is best done with a wire
brush. On mufflers without a catalytic converter the mesh
should be cleaned weekly, or replaced if necessary. On
mufflers fitted with a catalytic converter the mesh should be
checked, and if necessary cleaned, monthly. If the mesh is
damaged it should be replaced.
English – 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
If the mesh is frequently blocked, this can be a sign that the
Air filter
performance of the catalytic converter is impaired. Contact
your dealer to inspect the muffler. A blocked mesh will cause
the machine to overheat and result in damage to the cylinder
and piston.
The air filter must be regularly cleaned to remove dust and dirt
in order to avoid:
250R/252RX
•
•
•
•
•
Carburettor malfunctions
Starting problems
Loss of engine power
Unnecessary wear to engine parts.
Excessive fuel consumption.
265RX
Clean the filter every 25 hours, or more regularly if conditions
are exceptionally dusty.
Cleaning the air filter
240R, 240F
CAUTION! Never use a machine with a defective muffler.
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
Remove the air filter cover and take out the filter. Wash it
clean in warm, soapy water. Ensure that the filter is dry before
refitting it.
If the machine is used in dusty conditions the air filter should
be soaked in oil.See instructions under the heading Oiling the
air filter.
!
remain so for some time after stopping.This
also applies at idle speed. Contact can result
in burns to the skin. Remember the risk of
fire!
Cooling system
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
250R, 252RX
Remove the air filter cover and remove both filters, A and B.
A is an air filter and B is a pre-filter. Both must be washed in
warm soapy water and dried. Filter A must then be soaked in
oil, see instructions under the heading Oiling the air filter.
A
B
The cooling system consists of:
1
2
3
4
Air intake on the starter.
Fins on the flywheel.
Cooling fins on the cylinder.
Cylinder cover (directs cold air over the cylinder).
Clean the cooling system with a brush once a week, more
often in demanding conditions. A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
30 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
265RX
Bevel gear
Remove the air filter cover and take out the filter. Wash it
clean in warm, soapy water.
The bevel gear is filled with the right quantity of grease at the
factory. However, before using the machine you should check
that the bevel gear is filled three-quarters full with grease.Use
HUSQVARNA special grease.
The grease in the bevel gear does not normally need to be
changed except if repairs are carried out.
Ensure that the filter is dry before refitting it.
Spark plug
Oiling the air filter
Always use HUSQVARNA filter oil, art. no. 531 00 92-48.The
filter oil contains a solvent to make it spread evenly through
the filter.You should therefore avoid skin contact.
The spark plug condition is influenced by:
•
•
Incorrect carburettor adjustment.
An incorrect fuel mixture (too much or incorrect type of
oil).
Put the filter in a plastic bag and pour the filter oil over it.
Knead the plastic bag to distribute the oil. Squeeze the
excess oil out of the filter inside the plastic bag and pour off
the excess before fitting the filter to the machine. Never use
common engine oil. This would drain through the filter quite
quickly and collect in the bottom.
•
A dirty air filter.
These factors cause deposits on the spark plug electrodes,
which may result in operating problems and starting
difficulties.
If the machine is low on power, difficult to start or runs poorly
at idle speed: always check the spark plug first before taking
any further action. If the spark plug is dirty, clean it and check
that the electrode gap is 0.5 mm. The spark plug should be
replaced after about a month in operation or earlier if
necessary.
An air filter that has been in use for a long time cannot be
cleaned completely.The filter must therefore be replaced with
a new one at regular intervals. A damaged air filter must
always be replaced.
CAUTION! Always use the recommended spark plug type!
Use of the wrong spark plug can damage the piston/cylinder.
Check that the spark plug is fitted with a suppressor.
English – 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the
Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More
extensive work must be carried out by an authorised service workshop.
Daily
maintenance
Weekly
maintenance
Monthly
maintenance
Maintenance
Clean the outside of the machine.
X
X
Check that the harness is not damaged.
Make sure the throttle trigger lock and the throttle function correctly from a
safety point of view.
X
Check that the stop switch works correctly.
Check that the cutting attachment does not rotate at idle.
Clean the air filter. Replace if necessary.
X
X
X
Check that the guard is undamaged and not cracked. Replace the guard if
it has been exposed to impact or is cracked.
X
Check that the blade is correctly centred, is sharp, and is not cracked. An
off-centre blade will cause vibration that could result in damage to the
machine.
X
Check that the trimmer head is undamaged and not cracked. Replace the
trimmer head if necessary.
X
X
X
Check that the locking nut of the cutting equipment is tighten correctly.
Check that the locking screw is tightened when using a support cup with
bearings.
Check that the transport guard for the blade is intact and that it can be
secured correctly.
X
Check that nuts and screws are tight.
X
X
Check that there are no fuel leaks from the engine, tank or fuel lines.
Check the starter and starter cord.
X
X
Check that the vibration damping elements are not damaged.
Clean the outside of the spark plug. Remove it and check the electrode
gap. Adjust the gap to 0.5 mm or replace the spark plug. Check that the
spark plug is fitted with a suppressor.
X
Clean the machines cooling system.
X
X
X
X
Clean or replace the spark arrestor mesh on the muffler (only applies to
mufflers without a catalytic converter).
Clean the outside of the carburettor and the space around it.
Check that the bevel gear is filled three-quarters full with lubricant. Fill if
necessary using special grease.
Check the fuel filter from contamination and the fuel hose from cracks or
other defects. Replace if necessary.
X
X
X
Check all cables and connections.
Check the clutch, clutch springs and the clutch drum for wear. Replace if
necessary by an autorized service workshop.
Replace the spark plug. Check that the spark plug is fitted with a
suppressor.
X
X
Check and clean the spark arrestor mesh on the muffler (only applies to
mufflers fitted with a catalytic converter).
32 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
Technical data
Engine
240R
240F
3
Cylinder displacement, cm
Cylinder bore, mm
Stroke, mm
40,2
40,0
32
40,2
40,0
32
Idle speed, rpm
2700
12500
9190
1,8/9000
No
2700
12500
9190
1,8/9000
No
Recommended max. speed, rpm
Speed of output shaft, rpm
Max. engine output, acc. to ISO 8893
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
No
No
Manufacturer/type of ignition system
Spark plug
EM/ET
EM/ET
NGK BPMR 7A/
Champion RCJ 7Y
NGK BPMR 7A/
Champion RCJ 7Y
Electrode gap, mm
0,5
0,5
Fuel and lubrication system
Manufacturer/type of carburettor
Fuel tank capacity, litre
Walbro WT
0,8
Walbro WT
0,8
Weight
Weight without fuel, cutting attachment and guard, kg
Noise emissions
8,6
8,4
(see note 1)
Sound power level, measured dB(A)
114
114
114
116
Sound power level, guaranteed L
Noise levels
dB(A)
WA
(see note 2)
Equivalent noise pressure level at the operator’s ear,
measured according to EN/ISO 11806 and ISO 7917,
dB(A), min./max.:
100/104
98/101
Vibration levels
Vibration levels at handles, measured according to EN/
2
ISO 11806 and ISO 7916, m/s
At idle, left/right handles, min.:
2,1/2,1
2,4/2,8
2,9/2,4
4,0/3,5
3,2/3,0
3,8/4,1
1,9/2,4
4,2/4,7
At idle, left/right handles, max.:
At max. speed, left/right handles, min.:
At max. speed, left/right handles, max.:
Note 1: Noise emissions in the environment measured as sound power (L ) in conformity with EC directive 2000/14/EC.
WA
Note 2: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various
working conditions with the following time distribution: 1/2 idling and 1/2 max speed.
NOTE! The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting
attachments for the machine. The table indicates the lowest and highest values.
English – 33
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
Engine
250R
252RX
265RX
3
Cylinder displacement, cm
Cylinder bore, mm
Stroke, mm
48,7
44
50,8
45
65,1
48
32
32
36
Idle speed, rpm
2700
12500
9190
2,1/9000
No
2700
14000
10300
2,4/9000
No
2250
11500
9120
3,0/8400
No
Recommended max. speed, rpm
Speed of output shaft, rpm
Max. engine output, acc. to ISO 8893
Catalytic converter muffler
Ignition system
Manufacturer/type of ignition system
Spark plug
EM/ET
EM/ET
SEM GA 6CD
NGK BPMR 7A/
Champion RCJ 7Y
NGK BPMR 7A/
Champion RCJ 7Y
NGK BPMR 7A/
Champion RCJ 7Y
Electrode gap, mm
0,5
0,5
0,5
Fuel and lubrication system
Manufacturer/type of carburettor
Fuel tank capacity, litre
Walbro HDA
0,8
Walbro HDA
0,8
Tillotson HS
1,0
Weight
Weight without fuel, cutting attachment and guard, kg
Noise emissions
9,2
8,9
10,8
(see note 1)
Sound power level, measured dB(A)
112
114
112
114
115
116
Sound power level, guaranteed L
Noise levels
dB(A)
WA
(see note 2)
Equivalent noise pressure level at the operator’s ear,
measured according to EN/ISO 11806 and ISO 7917,
dB(A), min./max.:
97/104
96/103
98/100
Vibration levels
Vibration levels at handles, measured according to EN/
2
ISO 11806 and ISO 7916, m/s
At idle, left/right handles, min.:
2,7/3,2
3,5/6,0
1,0/1,0
2,1/2,0
2,8/2,8
4,5/3,9
1,2/1,4
1,6/1,7
4,5/4,0
5,1/4,6
3,0/3,9
3,9/5,1
At idle, left/right handles, max.:
At max. speed, left/right handles, min.:
At max. speed, left/right handles, max.:
Note 1: Noise emissions in the environment measured as sound power (L ) in conformity with EC directive 2000/14/EC.
WA
Note 2: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various
working conditions with the following time distribution: 1/2 idling and 1/2 max speed.
NOTE! The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting
attachments for the machine. The table indicates the lowest and highest values.
34 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Approved accessories 240R, 240F
Centre hole in blades/cutters, Ø 20 mm
Grass blade/grass cutter
Type
Cutting attachment guard, Art. no.
Output shaft thread M12
Multi 255-3 (Ø 255 3 teeth)
Multi 275-4 (Ø 275 4 teeth)
Multi 300-3 (Ø 300 3 teeth)
Maxi XS 200-22 (Ø 200 22 teeth)
Tricut Ø 300 mm
Trimmy S
502 26 34-01
502 26 34-01
502 26 34-01
502 27 22-01
503 91 60-01 / 502 26 34-01
503 91 60-01
503 91 60-01
503 91 60-01
-
Saw blade
Plastic blades
Trimmer head
Trimmy S II
Auto 55
Support cup
Fixed
With ball bearing
-
Approved accessories 250R
Centre hole in blades/cutters, Ø 20 mm
Grass blade/grass cutter
Type
Cutting attachment guard, Art. no.
Output shaft thread M12
Multi 255-3 (Ø 255 3 teeth)
Multi 275-4 (Ø 275 4 teeth)
Multi 300-3 (Ø 300 3 teeth)
Maxi XS 200-22 (Ø 200 22 teeth)
Maxi XS 225-22 (Ø 225 22 teeth)
Tricut Ø 300 mm
502 26 34-01
502 26 34-01
502 26 34-01
502 27 22-01
502 03 94-03
503 91 60-01 / 502 26 34-01
503 91 60-01
503 91 60-01
503 91 60-01
-
Saw blade
Plastic blades
Trimmer head
Trimmy S
Trimmy S II
Auto 55
Support cup
With ball bearing
-
Chopping blade
Set 537 16 55-01
Approved accessories 252RX
Centre hole in blades/cutters, Ø 20 mm
Grass blade/grass cutter
Type
Cutting attachment guard, Art. no.
Output shaft thread M12
Multi 255-3 (Ø 255 3 teeth)
Multi 275-4 (Ø 275 4 teeth)
Multi 300-3 (Ø 300 3 teeth)
Maxi XS 200-22 (Ø 200 22 teeth)
Maxi XS 225-22 (Ø 225 22 teeth)
Trimmy S
502 26 34-01
502 26 34-01
502 26 34-01
502 27 22-01
502 03 94-03
503 91 60-01
503 91 60-01
503 91 60-01
-
Saw blade
Trimmer head
Trimmy S II
Auto 55
Support cup
With ball bearing
Approved accessories 265RX
Centre hole in blades/cutters, Ø 20 mm
Grass blade/grass cutter
Saw blade
Type
Cutting attachment guard, Art. no.
Output shaft thread M12
Multi 300-3 (Ø 300 3 teeth)
Maxi XS 200-22 (Ø 200 22 teeth)
Maxi XS 225-22 (Ø 225 22 teeth)
Opti 255-22 (Ø 255 22 teeth)
Trimmy S
502 26 34-01
502 27 22-01
502 03 94-03
502 03 95-03
503 91 60-01
503 91 60-01
-
Trimmer head
Support cup
Trimmy S II
With ball bearing
English – 35
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
EC-declaration of conformity
(Applies to Europe only)
We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing saws Husqvarna 240R, 240F,
250R, 252RX and 265RX with serial numbers dating from 2002 onwards (the year is clearly stated on the rating plate, followed by
the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:
of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.
of May 3, 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.
of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.
For information relating to noise emissions, see the chapter Technical data.The following standards have been applied: EN292-2,
CISPR 12:1997, EN608.
SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has carried out voluntary type approval for
Husqvarna AB. The certificates have the numbers: SEC/94/053, 01/164/016 - 240R, SEC/03/1008, 01/164/036 - 240F, SEC/01/
819, 01/164/017 - 250R, SEC/97/493, 01/164/017 - 252RX, SEC/94/054, 01/164/018 - 265RX.
Huskvarna January 3, 2002
Bo Andréasson, Development manager
36 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy SII
1
2
7,0 m
23'
12 cm
5"
~ 3,5 m
11'
3
4
~ 15 cm
6'
7
5
6
"Clic"
8
9
35-50 NM
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto 55
1
2
3
>1,1 Kw
<1,1 Kw
1.)
2.)
4
5
2,7 mm - 9,0 m
3,0 mm - 7,5 m
3,3 mm - 6,0 m
15 cm
6"
8
7
6
15 cm
6"
15 cm
6"
15 cm
6"
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
´®z+H96¶6a¨
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1140252-26
´®z+H96¶6a¨
2004-01-09
Download from Www.Somanuals.com. All Manuals Search And Download.
We hope you find the links below useful. For further gardening information visit
Download from Www.Somanuals.com. All Manuals Search And Download.
|