DS160C
Manuel d’utilisation et d’entretien
Manuale di Istruzioni
Foreuse de chantier
Trapanatrice da cantiere
Manual de Instrucciones
Taladradora de obra
Operating Instructions
Drilling Machine
Betriebs-und Wartungsanleitung
Baustellen-Bohrmaschine
Gebruiksaanwijzing
Verplaatsbare Boormachine
Manual de Instrucoes
Perfuradora de obra
Bruksanvisning och Underhallsmanual
Borrmaskin
P/N 541404170
8/2006
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
PREFACE TO THE MANUAL
These operating instructions apply exclusively to drill stand, type DS 160 C. Please also read
the operating instructions that accompany your drill motor to verify their compatibility and
not to exceed the limitations of the DS 160 C drill stand.
Usage to the Intended Purpose
The drill stand is designed exclusively for core drilling in concrete, asphalt, brickwork or similar
building materials. Details of the maximum permissible drill bit diameter can be found under
“Technical Specifications”. Any use above and beyond the intended purpose endangers both
user and machine and is not permitted.
Before commencing drilling, always ensure that;
there is no danger of drilling through electric cables, gas, oil or other pipes,
the drilled holes do not undermine the stability of the structure,
you do not drill into or through any steel girders,
when drilling through walls, you cannot cause any damage at the drill exit point.
Strict care must be taken when drilling in areas where people or general public
are present. Local codes dictate proper protocol and must be observed.
Improper Usage
The drill stand must not be used for any kind of stirring, e.g. paint or similar;
drilling holes in soil, e.g. to drill holes for posts.
The drill stand must be mounted via anchor bolt or vacuum, do not attempt to
drill hand held or standing on base plate.
This drill stand incorporates the expertise of decades of experience in the field of concrete
drilling.
Before leaving our factory every machine passes an inspection program in which everything is
checked completely.
Following the instructions will ensure that your machine gives long service, in normal
operating conditions.
The user advice and spare parts mentioned in this document are given as an indication and
do not constitute an undertaking. No warranty will be granted in the event of errors or
omissions or for damage occurring during delivery or caused by the design or use of this
machine. We are very concerned about the quality of our products and we serve the right to
make any technical modifications to improve them without warning.
This document will assist the user particularly in:
·Information about the machine
·Information about its possible uses
4
Download from Www.Somanuals.com. All Manuals Search And Download.
·Prevent accidents due to unsuitable use, by an untrained person, during maintenance,
repairs, overhauls, handling or transport
·Improve the reliability and durability of the machine
·Ensuring correct use, regular maintenance and rapid repair in order to reduce stoppage
times and repair cost.
The manual should always be available at the place of work.
It should be read and used by any person installing or using the machine.
The obligatory technical regulations in force in the county where the machine is used
must also be adhered to for maximum safety.
GENERAL SAFETY INSTRUCTIONS
The use of symbols on the drill stands and in the manual identify advice concerning your
safety.
This symbol indicates that the machine is in conformance with the applicable European
directive.
WARNING
MANDATORY
PROHIBITED
INFORMATION
These signs give advice concerning your safety.
SPECIAL INSTRUCTIONS
·The drill stand is designed to provide safe and reliable service in operating conditions
corresponding with the instructions, but it can present dangers for the user and risks of
damage, consequently regular on site inspection is necessary to ensure:
·Perfect technical condition (use for the purpose for which it is intended and taking into
account any risks and correction of any malfunction detrimental to safety).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
·Use of a diamond core bit for water lubricated cutting of concrete, asphalt, marble, stone,
granite, brick and facings (porcelain, glazed tiles, ceramics, etc). The use of any other core
bit is forbidden (abrasive, saw, etc).
·Competent staff (qualifications, age, training) who have read and understood the
manual in detail before starting work: any electrical, mechanical or other problem should
be investigated by a qualified maintenance engineer (electrician, maintenance manager,
approved dealer, etc).
·That the warnings and instructions marked on the machine are followed (adequate
personal protection, correct use, general safety instructions, etc).
·That no modification, transformation or addition is detrimental to safety and that it is
carried out without prior authorization from the manufacturer.
MOTORS:
DIMAS: DM 225D with motor support collar
WEKA: DK 12 with motor support collar
DK 13 with motor support collar
DK 14 with motor support collar
DM 225 with motor support collar
CARDI: Talpa T0 with motor support collar
Talpa T1 with motor support collar
Motor characteristics: see the manufacturer’s manual supplied with the motor.
Please contact us regarding any other frame/motor combination.
1. Delivery
On delivery, carry out an immediate visual check for signs of physical damage and that no
components are missing.
The contents of the package should include:
Drill Stand - Base, Column, Carriage, Crank, Wheel Assembly, Vacuum Cap Plate, Vacuum
Gasket and Back Support, Operating Instructions and Ordered Accessories.
2. Technical Specifications
Base length
Base width
Height
15.50 in / 394 mm
9.50 in / 241 mm
32 in / 813 mm
30 lbs / 14 kg
Weight
Motor rating up to max. 3.5 hp / 2.4 kW
Drill bit diameter up to max.
6 in / 152 mm
Impact anchor; minimum tensile force 5.7 kN with M12 Fastener
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Assembly
Align holes on the wheel assembly (1) with the tapped
holes on rear of the base plate (2). Insert bolts (3)
through lockwashers (4), then insert bolts through
wheel assembly and screw onto base plate.
4. Description and Features of the Drill Stand
1
3
Tapered roller carriage.
Sealed ball bearing design.
4
Plumb and leveling guides.
Left and right crank handle drive with incorporated
adjustment tool. This adjustment tool adjusts
column angle, leveling screws and column angle lock.
Angle column capability.
Anchor base with incorporated vacuum capability.
Detachable wheel assembly.
2
Replaceable wear items.
Incorporated carrying handle.
Column angle and drill depth indicator decal.
Rigid drill collar motor mount.
Brass inserts for leveling bolts.
Precision rack and pinion drive.
5. Handling - Transport
Remove the diamond core bit from the drill motor.
Remove the motor from the carriage assembly.
Lower the carriage to the base and lock the brake.
The transport wheels enable the drill stand to be moved easily.
Tilt the drill stand backwards and hold the handle at the top of the column.
To avoid damaging the motor shaft, the motor must not be carried or moved by the shaft,
whether or not it is fitted with a drill or extension.
If the base is to be used as a vacuum mount, do not move the drill stand laterally or damage
and tearing away the vacuum seal may result. To avoid deforming the seal, remove the seal
when vacuum is not in use.
6. Inspection Before Starting Up
Please read the instructions for use prior to operating the machine for the first time.
The working area must be completely cleared, well lit and all safety hazards removed (no
water or dangerous objects in the vicinity).
The use of ear protection is mandatory.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The operator must wear protective clothing appropriate to the work he is doing. We
recommend that this includes both eye and ear protection.
Any person not involved in the work should leave the working area.
Use core bits which are suitable for the work to be done.
7. Fitting and Removing the Motor
Unplug the motor from the outlet.
Always remove the core bit before fitting or removing the motor.
Engage the carriage brake. The motor is mounted on the frame by means of a support collar.
8. Electrical Connection
ELECTRICAL SAFETY:
Operate this machine only on a supply equipped with a 30 mA grounded current-
limiting circuit breaker.
The Ground Fault Circuit Interrupter (GFCI) must be used correctly, including testing it
regularly. For tools supplied with an integral GFCI in the cable or in the main plug, if
the cable or plug has been damaged, repairs must be carried out by the manufactur-
er, one of his agents or by a qualified repair workshop to avoid any risks resulting
from errors.
Use single phase 2 pole plus grounded sockets for the appropriate voltage.
Make sure that the main voltage is the same as that on the manufacturer’s plate.
Extension cables, type HO7 RNF, should have an adequate cross section for the power:
2
3 x 2.5 mm up to 50 m or double for longer cables.
9. Mounting Methods
There are three options available for fastening the base plate of your drill stand. Fastening
with threaded rod and heavy-duty anchor, expanding anchor or vacuum.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Designation of the Components
Carrying Handle
Feed Handle
Carriage
Level and Plum Indicator
Carriage Brake
Back Support
Drill Motor Mount
Gear Rack
Depth and Angle Scale
Angle Column Lock Screw
Leveling Screws
Wheel Assembly
(Removable)
Vacuum Cap
(Removable)
Base Plate w/ Integrated
Vacuum
Vacuum Quick Disconnect
9
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Operation Positions
The drill stand can be used for drilling ceilings, floors and walls. Individual safety instructions
for each area of applications as described in the following chapters must be observed and
complied with.
The three main drilling directions (area of application) are:
Floor position:
Wall position:
The feed direction is vertical and downward.
The feed direction is horizontal.
Overhead position:The feed direction is vertical and upwards.
Floor Positions
A falling core can cause serious injury. The danger zone underneath the drilling area must be
sealed off and the core must be supported.
Wall Position
Before drilling into a wall, the operator must ensure that there are no obstructions at the exit
point and that there is no risk of injury.
Overhead Drilling
It is not permitted to secure the drill by means of the vacuum plate when carrying out
overhead drilling. Follow local codes for anchoring overhead. Overhead drilling may only be
carried out if a water collector and vacuum collection system is used. During overhead drilling,
only use impact anchors suitable for zones subject to tensile force.
Angle Drilling
When angle drilling, always work at low drilling pressure until the drill bit is completely
engaged.
12. Fastening the Drill Stand (Base Plate)
There are three options available for fastening the base plate;
Fastening with threaded rod and heavy-duty anchor or impact anchor;
Fastening by means of a threaded rod and locking nut with washer;
Fastening by means of a vacuum plate and vacuum pump.
Fastening by means of a ThreadedRod and Heavy-DutyAnchor or Impact Anchor
Fastening the drill stand base plate should be carried out without the drill motor installed.
To ensure that the device is securely fastened, only use heavy-duty anchors or impact anchors
approved by the building inspection authorities which may vary by country, providence, county
or city. When working overhead, only use anchors suitable for zones subject to tensile force.
For details of minimum tensile force, see, “Technical Specifications”.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill a hole for the anchor at a distance of 292
mm ( X ) from the hole center.
1 Nut and Washer
Drive the impact anchor and secure.
Screw in the all thread rod (2).
2 All thread rod
Slip on the base plate (4) over the thread rod.
Fit the washer and tighten nut (1) slightly.
3 Adjusting screw
Align the base plate (4) by means of the
adjusting screw (3).
4 Base plate
Tighten nut (1).
X
Fastening by means of a Thread Rod,
Washer and Lock Nut
If, for any reason, the anchoring surface does not provide sufficient hold for the anchor, a
thread rod must be used which passes through the brickwork, the wall or the ceiling and is
secured from the other side by means of a washer and locknut.
Fastening by means of a Vacuum Plate
It is not permitted to fasten the drill stand by means of a vacuum when carrying out overhead
drilling.
1
2
Vacuum Pump
(Actual pump may vary between Regions)
Vacuum Cap, Base Plate and Gasket
Connect the vacuum hose to the vacuum cap (1) and switch on the vacuum pump (2).
Set the vacuum base at the measured position and prime. A vacuum of at least 25 in.Hg must
be reached or until the plate is properly secure. Because this type of fastening depends on the
surface, it can only be implemented on smooth, level and non-porous surfaces. When fasten-
ing the drill stand, it must be ensured that the floor covering is firmly attached to the
undersurface and cannot work its way loose.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Setting the Angle of the Column
Remove the column lock bolt (1)
1
Loosen bolt on back support bracket (2).
3
The column can now be pulled into the desired
position, 0 to 45 degrees. Side decal provides
approximate measurements. If greater precision is
required use alternate measuring techniques.
Maximum column range is 45 degrees. Indictor strip
on the column shows various degrees (3).
2
14. Mounting the Drill Carriage
Risk of injury!
Always disconnect the power before mounting the drill carriage to the drill motor. Fingers
may be crushed between the column and drill carriage. For this reason, when mounting the
drill carriage, keep one hand on the handle and the other hand on the drill motor.
Align the column.
Mount the drill carriage.
15. Operating the Feed
Drilling into a live external power supply line can cause a fatal injury as the drill may
conduct current and voltage. A Ground Fault Circuit Interrupter (GFCI) offers no protection
in such situations, therefore care must be taken prior to drilling to ensure that electrocution is
avoided.
The use of levers or extensions to increase drilling pressure is prohibited. In order to
prevent the drill bit being damaged, it is important to ensure that the diamond core bit is
supplied with sufficient cooling water. Operate the feed handle manually.
The feed handle is designed to facilitate handling of the drill
and its flexible left/right hand fitting enables convenient
adaptation to individual drilling situations. The feed handle
can be switched to the other side as follows:
Pull off the feed handle in an axial direction.
Slip the feed handle onto the axle shaft on the opposite side.
A loose feed handle on the shaft may cause you to lose
control of the drill. For this reason, always ensure that the
feed handle is securely fitted on the shaft.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Maintenance
For details of maintenance work required for the drill motor, please refer to the enclosed
motor manufacturer’s documentation.
Routine Checks
Check electrical connections routinely before each use.
The following routine checks should be carried out monthly:
Check that all screws and fastening elements are properly secure.
Check the feed handle for easy movement.
Check the drive for easy movement and noise.
Check the column for wear and damage.
Check for movement or play in the drill carriage.
Always disconnect the electrical plug before cleaning your drill stand. The drill is virtually
maintenance-free and only requires cleaning. Never clean the drill motor with water or exces-
sively wet clothes.
Adjusting Carriage
Rollers
Loosen the locknut (1) using a 19mm open
1
end wrench, turn the eccentric shaft (2)
using an 8mm open end wrench, so there is
only slight pressure of the roller in contact
with the column wear plates (3). Holding
the eccentric shaft in place, tighten the
locknut. Follow this procedure for both
adjusting rollers.
2
3
If you are unable to achieve proper adjust-
ment, the rollers and/or column wear plates
may need to be replaced.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Wear Cylinders
Using a 4mm allen wrench, turn each of the 4 setscrews (4) clockwise until the nylatron wear
cylinders (5) are in slight contact with the column.
Side Cleaning Plates
Loosen each of the 4 cleaning plate capscrews (6) using a 3mm allen wrench and slide the
cleaning plate (7) so it is in contact with the column wear plates. Tighten the capscrews.
7
6
5
5
4
5
7
4
6
17. Spare Parts
Stocking Spare Parts
In order to gain maximum usage of your drill stand, it is necessary to ensure that an on-site
stock of the most important spare parts and those parts subject to wear are always ready and
on-hand.
The fitting and/or use of spare parts that we have not supplied or authorized may change the
technical configuration of the drill stand; thus impairing active and/or passive operational
safety. The manufacturer accepts no liability for damage due to the use of non-original spare
parts.
Ordering Spare Parts
The following spare parts lists with diagrams are designed to assist you when ordering spare
parts. When ordering spare parts, have the model number and part number ready.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
29
28
23
10
24 25 26 27
7
8
9
11
12
13
14
15
30
22
21
16
31
20 19 18
17
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill Stand Parts
Item Description
Part Number Qty
541404147
Comments
1
M4x16 Socket Head Capscrew
4
1
1
1
1
1
2
2
1
2
2
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
1
1
1
2
3
4
5
6
7
8
9
Handle Top Decal
Column Handle
T-Washer
Angle Support Bolt
Angle Support Assembly
M10x25 Socket Head Capscrew
M10 Lockwasher
Wheel Assembly
M6 Acorn Nut
M8x10 Socket Head Shoulder Screw
Leveling Screw Cap
M4 Washer
M4x16 Socket Head Capscrew
Gasket
541404097
541404781
541404078
541404079
541404109
541404155
541404148
541404113
541404141
541404139
541404084
541404146
541404147
541404083
541404142
541404143
541404107
541404081
541404151
541404136
541404053
541404782
541404783
541404144
541404098
541404786
541404145
541404080
541404099
542190734
541404153
Complete
Complete
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
M12 Acorn Nut
M12 Lockwasher
Drill Column Assembly
Column Spacer
M8x90 Socket Head Capscrew
M6x25 Socket Head Capscrew
Carriage Stop
Drill Carriage Assembly
Drill Base Casting
M16x70 Socket Head Shoulder Screw
Drill Operating Instruction Decal
Vacuum Cap Assembly
M10x1.5 Nut
Complete
Complete
Complete
Complete
Leveling Screw
Serial Number Decal
Husqvarna Decal
M6 Allen Wrench
Not Shown
16
Download from Www.Somanuals.com. All Manuals Search And Download.
15 16 17
12 13
1
18
10
9
11
5
8
19
18
6*
2
16
14
3
20 21
5
7*
4
22
23
*6.1
6.2
6.3
6.4
6.5
*7.1
7.2
7.3 7.4
7.5
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Item Description
Part Number Qty
Comments
1
2
3
4
5
6
6.1
6.2
6.3
6.4
6.5
7
7.1
7.2
7.3
7.4
7.5
8
Drill Carriage
Adaptor Plate
Drill Collar
Key
M8x25 Socket Head Capscrew
Locking Mechanism
Knob
Pin Retainer
Compression Spring
Pin
Spring Pin 2mmx16mm
Travel Lever Assembly
Travel Lever
Travel Lever Drive Hub
Stainless Steel Ball Plunger
Hex Nut M8x1.25
Travel Lever Knob
Carriage Drive Shaft
Bearing 17mmIDx35mmODx10mm Width 541404033
External Retaining Ring
Level Bubble
M4x10 Socket Head Capscrew
Side Cleaning Plate
M8x35 Socket Head Capscrew
Eccentric Shaft
541404784
541404029
541404030
541404031
541404126
541404114
541404087
541404085
541404089
541404086
541404088
541404101
541404043
541404044
541404133
541404132
541404045
541404040
1
1
1
1
3
1
1
1
1
1
2
1
1
1
1
1
2
1
2
2
1
4
4
2
2
6
2
4
2
4
4
1
1
Complete
Complete
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
541404042
541404049
541404130
541404035
541404152
541404039
541404036
541404131
541404102
541404038
541404129
541404032
541404152
541404154
Spacer
M12x1.75 Nut
Roller Assembly
Straight Shaft
M8x8 Socket Set Screw-Cup Point
Wear Cylinder
M8x35 Socket Head Capscrew
M8 Lock Nut
18
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
9
10
11
Item Description
Part Number Qty
Comments
1
2
3
4
5
6
7
8
9
Column
541404050
541404137
541404054
541404055
541404052
541404051
541404135
541404053
541404136
541404081
541404151
1
24
2
2
4
1
6
1
1
M3x8 Socket Head, Flat Head Screw
Depth Measurement Decal
Angle Measurement Decal
Wear Plate
Rack
M4x8 Socket Head Capscrew
Carriage Stop
M6x25 Socket Head Capscrew
Column Spacer
10
11
1
1
M8x90 Socket Head Capscrew
19
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
Item Description
Part Number Qty
Comments
1
2
3
Roller
Spacer
541404037
541404036
541404034
1
1
2
Bearing 12mmI.D.x24mmO.D.x6mm
20
Download from Www.Somanuals.com. All Manuals Search And Download.
1
6
5
3
2
4
Item Description
Part Number Qty
Comments
1
2
3
4
5
6
Angle Support Member
Angle Support Spacer
T-Washer Retainer
M6x20 Flat Socket Head Screw
M8 Socket Head Shoulder Screw
Angle Support Bushing
541404062
541404064
541404065
541404138
541404139
541404063
2
1
1
2
2
2
21
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
Item Description
Part Number Qty
Comments
1
2
3
4
5
Knob w/Stud
1/8 NPT Male Fitting
Ball Detent
Vacuum Cap
Vacuum Cap Gasket
541404073
541404071
541404072
541404785
541404070
1
1
2
1
1
22
Download from Www.Somanuals.com. All Manuals Search And Download.
HUSQVARNA CONSTRUCTION PRODUCTS
Product Limited Warranty
Equipment manufactured by Husqvarna Construction Products is warranted to be free
from defects in material and workmanship if operated properly, without abuse or negligence in
normal service applications for a period of two (2) years from date of purchase by the
original consumer purchaser.
Keep all payment records (bill of sale/delivery slip). The date on these records establishes
the warranty period. Should warranty service be required, you must show proof of purchase. If
proof of purchase cannot be supplied, the warranty period will determined from the date of
manufacture of the product.
All warranty claims will be determined after inspection at a designated facility. Write or
call Husqvarna at 17400 W. 119th Street, Olathe, KS 66061, 800-365-5040, for instructions. The
customer must prepay the freight and absorb any labor expense required to return or replace a
product submitted to Husqvarna for warranty consideration. Husqvarna will pay return shipping
expenses for repaired or approved replacement products. Under no circumstances will
Husqvarna be responsible for incidental or consequential damages.
The responsibility of Husqvarna under this warranty is limited to the repair or replace-
ment, at our option, of defective parts and assemblies at its plant in Olathe, KS and Torrance, CA
and does not cover engines, motors, pumps, transmissions and other trade accessories sold with,
attached to, or operated with Husqvarna products. Such components, parts and accessories are
subject to the original manufacturer’s warranty policy and procedures. Normal wear items, such
as filters, V-belts and wheels are not covered under this warranty.
The Husqvarna warranty does not apply to defects caused by abuse, modifications, low
voltage, acts of God, unreasonable use, faulty repairs made by others or damage or loss caused
by failure to provide reasonable maintenance. All warranties are void if the equipment or any
of its components are altered or modified by the purchased, or if the product is used in a
manner or with a blade not recommended by the manufacture.
The foregoing express warranties are in lieu of all other warranties. HUSQVARNA
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not allow exclusion of warranties or limitations of damages, so the
limitations and exclusions contained in this warranty may not apply to you. This warranty gives
you specific legal rights. You many have additional rights, which vary from state to state.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
|