Humax Flat Panel Television LAU 32TPVR User Manual
LAU-32TPVR  
LCD Digital and Analogue TV  
Digital 2 Tuner PVR Built-in  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LCD Digital and  
Analogue TV  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caution  
To reduce the risk of electric shock, do not remove cover(or back).  
No user serviceable parts inside. Refer servicing to qualified service personnel.  
Indicates a situation which, if not avoided, could damage the equipment or  
other apparatus.  
This symbol indicates dangerous voltage inside the LCD-TV that presents a  
risk of electric shock or personal injury. Indicates a hazardous situation which,  
if not avoided, could result in serious injury.  
This symbol indicates important instructions accompanying the LCD-TV.  
Read this manual carefully and make sure you understand the instructions provided.  
For your safety, check what the result of each action will be. Throughout the whole  
manual, pay special attention to the following marks that indicate hazardous situations.  
Indicates additional information to the user to make the user aware of possible  
problems and information of any importance to help the user to understand, to use  
and to maintain the installation.  
The information in this document is subject to change without notice.  
Copyright (Copyright ཱྀ 2005 HUMAX Corporation)  
Not to be copied, used or translated in part or whole without HUMAX's prior  
consent in writing except approval of ownership of copyright and copyright law.  
Warranty  
HUMAX does not have any responsibility for direct, indirect, accidental and other  
damage caused by the use of the information contained in this manual.  
Trademarks  
TM  
VIACCESS is a trademark of France Telecom.  
CryptoWorks(TM) is a trademark of Philips Electronics N.V.  
Irdeto is a trademark of Mindport BV.  
Nagravision is a registered trademark of KUDELSKI S.A.  
Conax is a trademark of Telenor Conax AS.  
'Dolby' and the double-D symbol are trademarks of Dolby Laboratories.  
Manufactured under the license from Dolby Laboratories.  
is a trademark of SRS Labs, Inc.  
TruSurround XT technology is incorporated under license from SRS Labs, Inc.  
Thank you for purchasing a HUMAX LCD-TV. Please read this user manual  
carefully in order to safely install, use and maintain the LCD-TV at maximum  
performance. Keep this user manual next to your LCD-TV to ensure the best  
performance possible.  
2. Caution  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Instructions  
This LCD-TV has been engineered and manufactured to assure your safety. You  
can prevent serious electrical shock and other hazards by keeping in mind the  
following:  
Do not place anything heavy, wet or magnetic on the LCD TV or the power  
cord. Never cover the ventilation openings with any material and never touch  
them with metalic or inflammable materials.  
Avoid operating the LCD-TV in extreme heat, humidity or areas affected by dust.  
+ Temperature : 0~50 C  
+ Humidity : 20~90RH  
Be sure to turn the LCD-TV off before plugging the power cord into the socket.  
Make sure that the power cord and the other cords are securely and correctly  
connected.  
Overloaded AC outlets and extension cords are dangerous, as are frayed power  
cords and broken plugs, which may cause electric shock or fire. Call your service  
technician for replacement.  
Do not use sharp tools such as a pin or a pencil near the LCD-TV, as they may  
scratch the LCD surface.  
Do not use a solvent, such a benzene(any liquids), to clean the LCD-TV,  
as it will damage the LCD surface.  
The apparatus shall not be exposed to dripping or splashing.  
Be careful when touching the LCD-TV.  
When you touch the LCD-TV, be careful not to get a cut on your fingers with an  
acrylic surface of the LCD-TV.  
Warning  
1
Follow these directions in order not to damage the power cord or plug.  
Do not modify the power cord or plug. Do not bend or twist the power cord  
too much. Make sure to disconnect the power cord using the plug rather than  
the power code. Keep heating appliances as far as possible from the power cord  
in order to prevent the cover vinyl from melting.  
2
Follow these directions. Failure to follow one of them may cause an electrical  
shock. Do not open the main body. Do not insert metals or inflammable objects  
inside the LCD-TV. Do not touch the power plug with wet hands. Disconnect the  
power cord in case of lightning.  
3
Do not use the LCD-TV when it is out of order. If you continue to use the  
LCD-TV when defective, serious damage can be caused to it. Make sure to  
contact your local LCD-TV distributor if the LCD-TV is out of order.  
4
Please do not insert metal or alien substances into the slots for the modules  
and smart cards. In doing so it can cause damage to the LCD-TV and reduce its  
life span.  
5
Hard Disk Drive : Do not move the LCD-TV or turn the power off suddenly  
while the hard disk drive is running. The company shall not be liable for any  
corruption of data on the hard disk drive caused by the carelessness or misuse  
of users. This LCD-TV provides up to 40GB of hard disk drive. Do contact your  
LCD-TV provider when you change the hard disk drive.  
3. Safety Instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Package Contents  
Front Panel  
Rear Panel  
07  
08  
09  
Before Using the TV  
Remote Control  
10  
10  
13  
14  
+ Main Remote Control  
+ Simple Remote Control  
+ Inserting the Batteries  
Mounting Device  
+ Assembling the Stand-Base  
+ Installing on the Wall  
15  
15  
15  
Setting Up the TV  
Connecting the External Equipment  
+ Connecting the Aerial  
+ Connecting the PC  
+ Connecting the External Devices  
+ Connecting the DVD  
+ Connecting the DVI  
16  
16  
16  
17  
17  
17  
Setting the Analogue Channels  
18  
18  
19  
20  
Using the Analogue TV  
+ Setting the Analogue Channels Automatically  
+ Setting the Analogue Channels Manually  
+ Editing the Analogue Channels  
Basic Operation  
21  
21  
21  
21  
21  
21  
22  
22  
22  
22  
+ Powering the TV On/Off  
+ Changing the Input Mode  
+ Volume Control  
+ Selecting the Channel  
+ Choosing your Language  
+ Listing Channels  
+ Using the OK Button  
+ Using the Audio Button  
+ Setting the Sleep Time  
Setting the Picture  
+ Mode  
+ Colour Temperature  
23  
23  
23  
Setting the PIP/TWIN  
+ PIP/TWIN  
+ Using the PIP Buttons in the Remote Control  
+ Using the Digital Channels in PIP/TWIN Mode  
24  
24  
25  
25  
Changing the Sound  
+ Effect  
+ Auto Volume Level  
+ TruSurround XT  
+ Sound Source  
+ Using the Sound Button in the Remote Control  
26  
26  
26  
26  
26  
26  
Setting the Time  
+ Setting the Current Time  
+ Automatically Turning the TV On and Off  
27  
27  
27  
Setting the System  
+ Language  
+ OSD Transparency  
+ AV Output  
+ Antenna Power  
+ Aspect Ratio  
+ Backlight Brightness  
28  
28  
28  
28  
28  
28  
28  
Displaying the Teletext Information  
Setting the PC Input  
29  
30  
4. Contents - Analogue TV  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Recording  
+ Instant Recording  
31  
31  
32  
32  
33  
33  
34  
35  
Recording and Playback  
(PVR function)  
- Setting the Recording Quality  
- Setting the Clipping Noise Reduction  
+ Recording Reservation  
- Adding Recording Reservations  
- Editing Recording Reservations  
+ Time Shifted Recording  
Playback  
37  
37  
39  
39  
39  
39  
40  
41  
41  
41  
41  
41  
41  
42  
42  
42  
+ Programme Playback  
+ Editing Recorded Programmes  
- Editing Title  
- Delete File  
- Copy File to External Device  
- Connecting the External HDD  
+ Playback Control  
- Play / Pause  
- Rewind to Previous Scene  
- Fast forward to Next Scene  
- Recording  
- Direct Jump  
- Instant Reply  
- Repeat between A and B  
- Bookmark  
HDD Control  
+ Checking the Hard Disk Drive  
+ Connecting the External HDD  
43  
43  
44  
5. Contents - PVR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Digital TV Channel Setup  
Basic Operation  
+ Switching Channel  
+ Changing the Subtitle Language  
+ Changing an Audio Language  
+ Programme Information - Information Banner (I-Plate)  
45  
46  
46  
46  
46  
47  
Using the Digital TV  
Channel List  
+ Displaying and Switching Channel List  
+ Editing Channels  
49  
49  
49  
52  
+ Editing Favourite Channels  
Programme Guide  
+ Viewing Programme Guide Information  
+ Finding a Programme  
53  
53  
54  
55  
+ Adding Reservations by Guide  
Setting the Preferences  
+ Parental Control  
+ Local Setting  
56  
56  
57  
59  
+ Miscellaneous Settings  
Installation  
60  
60  
61  
62  
63  
+ Automatic Search  
+ Regional Search  
+ Manual Search  
+ Default Setting  
System Information  
+ Status  
+ Signal Detection  
+ Common Interface  
64  
64  
64  
65  
Game  
65  
Software Upgrade  
66  
+ Software Update from PC  
66  
67  
67  
67  
68  
Menu Map  
Appendix  
+ LCD TV Menu  
+ PC Main Menu  
+ Digital TV Menu  
69  
69  
70  
Troubleshooting  
+ Troubleshooting  
+ Error Message  
72  
73  
74  
Specification  
Glossary  
Service and Support  
6. Contents - Digital TV  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Package Contents  
+ Please check all package contents before using your LCD-TV.  
+ Package Contents may be different according to the area.  
LCD - TV  
User's Manual  
AAA Batteries (x2)  
Power Cable  
PAGE  
NR-103  
Simple Remote Control  
(SR-10)  
Main Remote Control  
(NR-103)  
PC Cable  
7. Package Contents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Panel  
TV/AV  
OK  
MENU  
VOL  
CH  
TV/AV  
6
OK  
5
MENU  
4
ൖ VOL ൘G 3  
̷GGCH ̵G 2  
STANDBY  
1
1.  
: STANDBY  
Switches between Operation and Standby modes.  
Displays Red colour when the set is in standby mode.  
Changes to Green colour when the set is switched on.  
2. ̷GGCH ̵  
Selects a programme or a menu item.  
3. ൖ VOL ൘  
Adjusts the volume. Adjusts the menu setting.  
4. MENU  
Displays the menu.  
5. OK  
Selects a menu or confirms the selected operation.  
6. TV/AV  
Selects the input signal (Digital TV, Analog TV, AV1, AV2, AV3, S-Video,  
Component, PC, DVI ).  
8. Front Panel  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15. COMMON INTERFACE  
16. SMARTCARD SLOT  
10. S/PDIF  
11. H/P (Headphone)  
Red3 : AUDIO : R  
12. AV3 IN  
White : AUDIO : L  
Yellow : VIDEO  
13. S-VIDEO  
Red2 : AUDIO : R  
White : AUDIO : L  
Red1 : Pr  
14. COMPONENT  
17. MAIN POWER  
Blue : Pb  
Green : Y  
VIDEO  
L
-
AUDIO  
-
R
VIDEO  
L
-
AUDIO  
-
R
VIDEO  
L
-
AUDIO  
-
R
75ⵕ  
AV1 IN  
AV OUT  
AV2 IN  
AC INPUT 1  
DVI INPUT 2  
PC INPUT 3  
AUDIO INPUT 4  
RS-232C 5  
USB MASTER PORT 6  
AV1 IN 7  
AV2 IN 7  
AV OUT 8  
ANT IN 9  
1. AC INPUT  
Connect the supplied AC power cord.  
2. DVI INPUT  
Connect to the digital video output jack of an external device with DVI output.  
3. PC INPUT  
Connect to the video output jack on your PC, using the PC cable supplied.  
4. AUDIO INPUT  
Connect to the audio output jack on your PC or your external device with DVI output.  
5. RS-232C  
Connect to the RS-232C port on your PC for software upgrade.  
6. USB MASTER PORT  
Connect to the USB port on an external HDD for moving the various digital data to/from an  
external HDD.  
7. AV1 IN, AV2 IN  
Connect for the video and audio input to external devices with RCA cables.  
8. AV-OUT  
Connect for the video and audio output to external devices such as a VCR or DVD.  
9. ANT IN (Antenna In)  
Connect to your aerial for digital and analogue TV signal.  
10. S/PDIF  
Connect to Dolby digital decoder for the digital audio signal output.  
11. H/P (Headphone)  
Connect to your headphone.  
12. AV3 IN  
Connect for the video and audio input to external devices with RCA cable.  
13. S-VIDEO  
Connect to an external device with S-Video output.  
14. COMPONENT  
Connect to an external device with Component output, such as DVD.  
15. COMMON INTERFACE  
Use for one CA Module with a smart card.  
16. SMARTCARD SLOT  
Slot for Smartcard.  
17. MAIN POWER  
Main Power Button.  
9. Rear Panel  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
All the functions can be controlled with the Remote Control handset. Some function  
can also be adjusted with the buttons on the front panel of the set.  
Both the Main Remote Control to control the all functions and the  
Simple Remote Control to control the some simple functions are provided.  
Before you use the Remote Control handset, please install the batteries.  
Main Remote Control  
EFFECT  
NR-103  
+/-  
+ -  
+/-  
25. SUBTITLE  
26. SOUNDTRACK/AUDIO  
F
27. ASPECT RATIO  
28. PIP and TSR BUTTONS  
29. TELETEXT BUTTONS  
/ PLAYBACK BUTTONS  
NR-103  
10. Remote Control  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
1. STANDBY  
15. OK  
Selects a menu, or confirms the  
Switches between Operation  
and Standby modes.  
selected operation and displays  
the channel list whilst watching  
a programme.  
2. SLEEP  
Sets the sleep time.  
16. EXIT  
3. MUTE  
Mutes the audio.  
Exits the main menu or Guide  
screen.  
4. TV/AV  
17. MENU  
Selects input signal between TV  
and another signals.  
Displays the main menu.  
18. DTV Setup  
5. WIDE  
Displays the DTV Setup menu in  
the Digital TV mode.  
Enlarges the picture to the wide  
aspect ratio in the Digital TV mode.  
Unavailable when PIP or TWIN mode.  
19. CH +/- and PAGE +/-  
Changes the Channel or Page.  
6. SND (Sound) EFFECT  
Changes the sound mode.  
20. INFORMATION  
Displays the information about  
the channel and programme  
in the Digital TV mode.  
7. PIC (Picture) MODE  
Changes the picture mode.  
8. NUMERICAL BUTTONS (0~9)  
Enters a channel number or menu  
option number.  
21. VOL +/-  
Adjusts the audio volume.  
A
B
C
22. FAV CH  
9. LIST  
Displays the Favourite Channel  
List in the Digital TV mode.  
Displays the channel list.  
10. TEXT  
23. RADIO CH  
Not used for this product.  
Switches to digital Radio  
channel in the Digital TV mode.  
11. COLOUR BUTTONS (R/G/Y/B)  
Selects colour keys for teletext in the  
Analog TV and Digital TV modes.  
24. DTV CH  
Switches to digital TV channel  
in the Digital TV mode.  
12. BACK  
Returns to the previous menu and  
screen.  
D
E
25. SUBTITLE  
Changes the subtitle language  
in the Digital TV mode.  
13. GUIDE  
Displays the Programme Guide.  
26. SOUNDTRACK/AUDIO  
Lists alternative soundtracks  
enable stereo, dual or mono  
sound in the Digital TV mode.  
14. ARROW BUTTONS (  
,
,
,
)
Moves the cursor to the up, down,  
left or right menu option.  
F
27. ASPECT RATIO  
Changes the aspect ratio  
of the screen.  
11. Remote Control  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
PIP AND TSR BUTTONS  
K. TSR  
K
P
P
(TIME SHIFTED RECORDING)  
Switches the Time Shifted  
Recording On and Off.  
L
M
N
O
L. PIP/TWIN  
Changes PIP/TWIN mode.  
A
C
G
B
D
H
M. PIP INPUT  
Change the PIP input mode.  
E
I
F
J
N. PIP POSITION  
Control the PIP position.  
O. SWAP  
NR-103  
Switch between main screen  
and PIP screen.  
P. PIP CH +/ -  
Change the PIP channel.  
TELETEXT BUTTONS  
PLAYBACK BUTTONS (for PVR)  
A. TELETEXT (  
)
B. PLAY / PAUSE (  
)
Activate/Deactivate the teletext service.  
Plays or pause a programme.  
C. MIX (  
)
C. FAST REWIND (  
)
Displays the teletext with the  
broadcasting screen.  
Rewinds a programme. Each time  
you press this button, the scenes  
is rewound more faster divided into  
4 steps.  
D. INDEX (  
)
D. FAST FORWORD (  
)
Displays the teletext index page.  
Fast forwards a programme. Each  
time you press this button, the scene  
is forwarded faster divided into 4 steps.  
E. UPDATE (  
)
E. STOP (  
)
Displays the TV picture on the  
screen whilst waiting for the new  
teletext page.  
Stops a programme.  
F. REVEAL (  
)
F. RECORD (  
)
Displays the concealed information.  
Records a programme.  
G. MODE (  
)
G. INSTANT REPLAY (  
)
Programme a colour button in LIST  
mode.  
Replays the programme from 7  
seconds previous scene.  
H. SIZE (  
)
H. A-B REPEAT (  
)
Selects a text size.  
Plays back a specified block  
repeatedly.  
I. HOLD (  
)
I. BOOKMARK LIST (  
)
Holds function during teletext display.  
Stop the automatic page change.  
Displays the list of saved viewing  
positions.  
J. SUBPAGE (  
)
J. ADD BOOKMARK (  
)
Search the sub-page using the  
sub-code.  
Saves the present viewing position  
as a bookmark.  
12. Remote Control  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
Simple Remote Control  
1. STANDBY  
2. MUTE  
3. TV/AV  
4. OK  
5. CH (Channel) ̵/̷  
6. VOL (Volume) ̵/̷  
7. BACK  
8. MENU  
9. GUIDE  
10. PAUSE / PLAY  
11. LIST  
1. STANDBY  
6. VOL (Volume) +/-  
Switches between Operation  
and Standby modes.  
Adjusts the audio volume.  
7. BACK  
2. MUTE  
Returns to the previous menu  
and screen.  
Mutes the audio.  
3. TV/AV  
8. MENU  
Selects input signal between  
TV and another signals.  
Displays the main menu.  
9. GUIDE  
4. OK  
Displays the Programme Guide.  
Selects a menu, or confirms the  
selected operation and displays  
the channel list whilst watching  
a programme.  
10. PAUSE/PLAY  
Plays or pause a programme.  
11. LIST  
5. CH (Channel) +/-  
Displays the channel list.  
Changes the Channel.  
13. Remote Control  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control  
Inserting the Batteries  
You must insert or replace the batteries in the remote control when you:  
+ Purchase the TV.  
+ Find that the remote control is no longer operating correctly.  
Pull  
Push  
Lock  
Insert  
1
2
3
1. Pull the battery cover upward in the arrow direction to remove.  
2. Insert the batteries as illustrated in the battery compartment.  
3. Put the battery cover back.  
4. For Simple Remote Control, insert the batteries in the same way.  
+ Apply two 1.5V batteries of AAA type. Don˅t mix used batteries with new  
batteries.  
+ Remove batteries when you don˅t use the remote control for long periods.  
Liquid leakage from old batteries may cause operation failure.  
Notes for using remote control  
+ Make sure these are no objects between the remote control and its sensor.  
+ Don˅t place the remote control near a heater or damp place. Strong  
impact on remote controller may cause operation failure.  
+ The signal from the remote control may be subjected to interference  
from sunlight or other strong light.  
14. Remote Control  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting Device  
This describes how to set up the LCD-TV. Select the most appropriate procedure  
depending on your requirements.  
If you encounter any problem when setting up the LCD-TV, please contact  
your local LCD-TV distributor.  
Assembling the Stand-Base  
2
1
1. Attach your LCD-TV with the stand-base.  
2. Firmly fix the stand-base and the LCD-TV using the 4 screws.  
Note : Firmly fix the stand-base for the LCD-TV before moving it,  
as the stand-base may fall and could cause serious injury.  
Installing on the Wall  
You can install the LCD-TV on the wall using a mounting bracket (sold separately).  
To reduce the risk of damage from falling, this LCD-TV should be secured at all times.  
(The LCD TV in the picture may not look exactly like yours.)  
1
2
3
1. Before you install, separate the LCD-TV and stand-base.  
2. Attach your main body bracket on the LCD-TV and fix using screws firmly.  
3. Stick the LCD-TV with main body bracket into the wall bracket attached on the wall.  
4. Tighten up a safety-screw.  
Note :  
_ Do not install the set on a weak surface such as plaster or foam board.  
_ Be at enough distance to open CI door between the LCD-TV and the wall  
when installing on the wall. If the LCD-TV is not at proper distance from the  
wall, the CI door may be not opened enough.  
15. Mounting Device  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the External Equipment  
You can connect additional equipment, such as VCRs, DVD, etc. to your set.  
Examples are shown below.  
Connecting the Aerial  
To view television channels correctly, a signal must be received by the set  
from one of following sources :  
+ An outdoor aerial  
+ An indoor aerial ( not recommended )  
ANT IN  
1. Connect the aerial to the ANT IN on the bottom of the LCD-TV.  
2. Press the TV/AV button on the remote control.  
3. Select Analog TV or Digital TV.  
Connecting the PC  
PC INPUT  
AUDIO INPUT  
AC INPUT  
1. Turn off your computer and LCD-TV.  
2. Connect a PC D-Sub cable between your PC and PC INPUT of the LCD-TV and  
then fasten the screws of both sides on the cable.  
3. Connect a PC Audio Cable between the Sound Output jack of the sound card  
on your PC and the AUDIO INPUT of the LCD-TV.  
4. Connect the Power cable to the AC INPUT jack on the rear of your LCD-TV.  
And connect power code to a power outlet.  
5. Power on your PC before turning on the LCD-TV.  
16. Connecting the External Equipment  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the External Equipment  
Connecting the External Devices  
1. Connect video/audio RCA cable as indicated in the diagram.  
2. For optimal visual image, use S-VIDEO lead(cable not supplied).  
3. If you wish to connect the optical S/PDIF terminal and Dolby Digital decoder  
to listen digital audio, connect as follows. (cable not supplied)  
S/PDIF  
VCR  
AV IN  
AV OUT  
DVD  
AV1 IN  
AV2 IN  
AV OUT  
Connecting the DVD  
Connect AUDIO L/R to AUDIO OUT connector of the DVD.  
For viewing, use S-Video or Component Video Input (Y, Pb, Pr).  
For listening, use Component Audio Input (Audio L/R).  
S-Video  
R
L
SET-TOP BOX  
Pr  
Pb  
Y
DVD  
Connecting the DVI  
Connect the DVI cable and Audio cable as follows.  
For viewing, use DVI INPUT. For listening, use AUDIO INPUT.  
DVI INPUT  
AUDIO INPUT  
DVI  
L - ADUIO - R  
SET-TOP BOX  
DVD  
17. Connecting the External Equipment  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Analogue Channels  
Setting the Analogue Channels Automatically  
You can scan for the frequency ranges available to you (and availability depends on  
your country.) Automatically allocated programme numbers may not correspond to  
actual or desired programme numbers. However you can sort numbers manually and  
clear any channels you do not wish to watch. It˅s only for analogue TV mode.  
1. Press the MENU button.  
2. Select Channel using the ̵/̷ button, and press the OK or ൘Gbutton.  
3. Select Auto Programme using the ̵/̷ button, and press the OK or ൘ button.  
4. Select System using the ̵/̷ button, and press the ൖGor ൘ button to select  
a particular system.  
BG : I : DK  
5. Select Storage From using the ̵/̷ button, and press the ൖ, ൘ or NUMERICAL  
(0~9) button to enter the starting number to store the scanned programme.  
6. Select Start Search using the ̵/̷ button, and press the OK or ൘ button  
to start auto scanning. To stop the search before it has finished, press  
the BACK button.  
The search will end automatically. Channels are sorted and stored in an order,  
and then the programme originally selected is displayed.  
In the digital TV mode, you can select Setup Digital Channel menu instead  
of Channel menu.  
18. Setting the Analogue Channels  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Analogue Channels  
Setting the Analogue Channels Manually  
The Manual Programme allows you to manually tune and arrange the channels in the  
order you desire. You can also assign a channel name with characters to each channel  
number. It's only for analogue TV mode.  
1. Press the MENU button.  
2. Select Channel using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Manual Programme using the ̵/̷ button, and press the  
OK or ൘ button.  
4. Select System using the ̵/̷ button, and press the ൖGor ൘ button to select  
a particular system.  
BG : I : DK  
5. Select Band using the ̵/̷ button, and press the ൖGor ൘ button to select  
a particular system.  
V/UHF : Cable  
6. If you know the channel number to be stored, select Channel using the ̵/̷  
button, and press the ൖ, ൘ or NUMERICAL (0~9) button to select number.  
If you do not know the channel number, select Search using the ̵/̷Gbutton,  
and press the ൖGor ൘ button to start search.  
7. Select Programme No. using the ̵/̷Gbutton, and press the ൖ, ൘ or  
NUMERICAL (0~9) button to assign a programme number into the  
channel.  
8. Select Name using the ̵/̷Gbutton, and press the OK or ൘Gbutton  
to change a name.  
To select a letter (A~Z, 0~9, +, -), press the ̵/̷Gbutton.  
To move on the previous or next letter, press the ൖGor ൘ button.  
To store the changing name, press the OK button.  
9. Select Fine Tune using the ̵/̷Gbutton, and press the ൖGor ൘ button to  
fine-tune the channel manually. If the signal is weak or distorted, you may  
have to fine-tune the channel manually.  
10. When you are satisfied with your choice, press the BACK button to  
store the current setting values.  
19. Setting the Analogue Channels  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Analogue Channels  
Editing the Analogue Channls  
This function enables you to delete, copy, move, or skip the stored channel. It˅s only  
for analogue TV mode.  
1. Press the MENU button.  
2. Select Channel using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Edit Programme using the ̵/̷ button, and press the OK or ൘Gbutton.  
The programme list is displayed in the main screen.  
4. Select the programme name to edit with ̵/̷/ൖ/൘ button and press  
the Colour (R/G/Y/B) buttons to delete, copy, move, or skip the programme.  
+ Delete button : RED  
+ Move button : YELLOW  
+ Copy button : GREEN  
+ Skip button : BLUE  
Skipping a Channel  
_ Select a channel to skip with the ̵/̷/ൖ/൘ button.  
_ Press the BLUE button, the channel selected will change to the blue colour.  
Thereafter these channels will be skipped when using the CH +/- button.  
_ To return to normal status, select the skipped channel and then press again  
the BLUE button for 2~3 seconds.  
Moving a Channel  
_ Select a channel to move with the ̵/̷/ൖ/൘ button.  
_ Press the YELLOW button to select the channel you wish to move.  
Use the ̵/̷/ൖ/൘ button to move the channel to the desired position,  
and then press the YELLOW button again to store.  
Copying a Channel  
_ Select a channel to copy with the ̵/̷/ൖ/൘ button.  
_ Press the GREEN button.  
Deleting a Channel  
_ Select a channel to delete with the ̵/̷/ൖ/൘ button.  
_ Press the RED button. If you press the RED button again, the selected channel  
will be deleted.  
While editing the programme, you can switch to the channel you select.  
20. Setting the Analogue Channels  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operation  
Powering the TV On/Off  
1. Connect the plug to the wall outlet.  
2. Press the MAIN POWER button on the rear of the LCD-TV to turn the TV power on.  
3. Press the STANDBY, TV/AV or CH +/- button on the front of the LCD-TV or  
press the STANDBY, TV/AV, CH +/- or NUMERICAL (0~9) buttons on the  
remote control to switch the TV on.  
Note : To place the TV in standby mode, press the STANDBY button  
again on the remote control or on the front of the LCD-TV.  
It can be useful when you wish to interrupt viewing temporarily  
(during a meal, for example).  
4. To turn the TV power off, press the MAIN POWER button on the rear of the  
LCD-TV.  
Note : Do not leave the TV in standby mode for too long (on holiday,  
for example). Turn the TV off by pressing the MAIN POWER button  
on the rear of the LCD-TV. It is best to disconnect the power cord.  
Changing the Input mode  
1. Press the TV/AV button to change the input mode.  
2. Select your desired mode using the ̵/̷ button, and press the OK button.  
You can also change the input mode by pressing the TV/AV button repeatedly.  
Volume Control  
1. Press the VOL +/- buttons to adjust the audio volume.  
2. Press the MUTE button to mute the sound.  
Selecting the Channel  
1. Press the CH +/- or NUMERICAL (0~9) buttons to change the  
channel number.  
Choosing Your Language  
When you start using your television for the first time, you must select the language  
which will be used for displaying menus and indications.  
1. Press the MENU button.  
2. Select System using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Language using the ̵/̷ button, and press the ൖGor ൘ button to  
select a particular language.  
4. When you are satisfied with your choice, press the EXIT button to return  
to normal viewing.  
21. Basic Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operation  
Listing Channels  
You can watch the programme list while watching analogue TV.  
1. Press the LIST button.  
2. Select a channel using the ̵/̷ button, and press the OK button to switch  
to the selected channel. You can also move to the next or previous list page  
using the PAGE +/- button.  
Using the OK button  
When you press the OK button, the information of the channel appears :  
_ Channel number, channel name, and current time in the Analog TV mode  
_ External input mode and current time in the AV input mode.  
_ The information of Main and PIP screen in the PIP mode.  
If you wish to disappear the information, press the OK button again.  
In the audio mode also, the information appears.  
Using the Audio button  
You can hear the sound with various modes. ( Mono, Stereo, Dual mode)  
Press the SOUNDTRACK/AUDIO button repeatedly to switch into other mode.  
If it is not switched, it's the channel that various modes are not supplied.  
Setting the Sleep Time  
You can select a time for the TV to turn off automatically.  
Press the SLEEP button repeatedly until the desired time appears.  
The number changes from Off . 10 . 20 . 30 . 60 . 90 . 120 . 180 . 240.  
When the selected time is out, the TV will turn off automatically.  
To cancel the sleep time, press the SLEEP button repeatedly and select  
--- (Sleep Off).  
22. Basic Functions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Picture  
Mode  
You can select the picture type you prefer.  
1. Press the MENU button.  
2. Select Picture using the ̵/̷Gbutton, and press the OK or ൘Gbutton.  
3. Select Mode using the ̵/̷Gbutton and press the ൖGor ൘ button to select  
a particular mode. If you select User, you can control the value manually.  
Standard : Dynamic : Movie : Mild : User  
4. On the Standard, Dynamic, Movie, or Mild, the value of the Brightness,  
Contrast, Sharpness and Colour is changed automatically. You can also set  
these options simply by pressing the PIC MODE (Picture Mode) button.  
Note : If you change the value of the Brightness, Contrast, Sharpness  
and Colour, the User is selected automatically.  
Colour Temperature  
You can select the picture colour tone you prefer.  
1. Press the MENU button.  
2. Select Picture using the ̵/̷Gbutton, and press the OK or ൘ button.  
3. Select Colour Temperature using the ̵/̷Gbutton and press the  
OK or ൘Gbutton.  
4. Select Colour Temp using the ̵/̷Gbutton, and press the ൖGor ൘ button  
to select a particular colour tone. If you select User, you can control the  
value manually.  
Normal : Cool : Warm : User  
5. On the Normal, Cool, or Warm, the value of the R/G/B Gain is changed  
automatically.  
Note : If you change the value of the R/G/B Gain, the User is selected  
automatically.  
23. Setting the Picture  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the PIP/TWIN  
PIP/TWIN  
With PIP, Picture in Picture, you can call up a small screen within the main screen.  
This enables you to watch two different input sources at the same time. In this way,  
you can watch TV programme or monitor the video input from any connected  
devices while watching TV or other video input.  
1. Press the MENU button.  
2. Select Picture using the ̵/̷Gbutton, and press the OK or ൘Gbutton.  
3. Select PIP/TWIN using the ̵/̷ button, and press the OK or ൘Gbutton.  
4. Select Main Input using the ̵/̷ button, and press the ൖ or ൘ button to  
select a particular thing.  
Digital TV : Analog TV : AV1 : AV2 : AV3 : S-Video : Component : PC : DVI  
5. Select PIP/TWIN using the ̵/̷ button, and press the ൖGor ൘ button to  
select a particular thing.  
_ Off  
: Switch PIP mode off.  
_ PIP (Picture in Picture) : Switch PIP mode on.  
_ TWIN 1, TWIN 2  
: Switch two Twin screen modes on.  
(Twin screen 1, Twin screen 2)  
6. Select PIP/TWIN Input using the ̵/̷ button, and press the ൖ or ൘  
button to select a particular thing.  
Digital TV : Analog TV : AV1 : AV2 : AV3 : S-Video : Component : PC : DVI  
Note : You can only select different inputs between Main Input and  
PIP/TWIN Input except Digital TV mode.  
You can enjoy two digital channels simultaneously in each screen.  
7. Select PIP Position using the ̵/̷ button, and press the ൖGor ൘ button to  
move the PIP picture to another corner of the screen.  
Left-Top  
Right-Top  
Left-Bottom  
Right-Bottom  
Note : If you wish to select PIP Position, you must set the PIP/TWIN  
mode to PIP.  
24. Setting the PIP/TWIN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the PIP/TWIN  
8. Select Swap using the ̵/̷ button, and press the ൘ button to exchange the  
picture in the main screen and small screen. Not available in PC Mode.  
In case of PIP  
2
1
1
2
In case of TWIN1 or TWIN2  
2
2
1
1
Using the PIP Buttons in the Remote Control  
You can use the PIP buttons on the remote control. Press PIP/TWIN button  
repeatedly during watching TV channel to switch into PIP or TWIN mode.  
Press PIP INPUT button repeatedly to change the input mode in the small screen.  
Press PIP POSITION button repeatedly to move the position of the small screen.  
Press the PIP CH+ / PIP CH- button to change the TV Channels in the small screen.  
Press SWAP button to exchange the picture in the main screen and small screen.  
Using the Digital Channels in PIP/TWIN Mode  
You can watch two digital channels simultaneously using PIP/TWIN mode.  
1. Press PIP/TWIN button during watching digital TV channel.  
2. Press PIP INPUT button repeatedly, and change to Digital TV  
mode in the small screen.  
3. Press PIP CH+ / PIP CH- to change the channel in the small screen.  
Note : There are the programme which you cannot watch in the small  
screen such as scrambled programmes or data programmes.  
25. Setting the PIP/TWIN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Sound  
You can select the preferred sound settings which corresponds with the personal  
sound settings.  
1. Press the MENU button.  
2. Select Sound using the ̵/̷ button, and press the OK or ൘ button.  
Effect  
3. Select Effect using the ̵/̷ button and press the ൖGor ൘button to select  
a particular thing. If you select User, you can control the value manually.  
Flat : Speech : Movie : Music : User  
4. On the Flat, Speech, Movie, or Music, the value of the Bass, Treble, and  
Balance is changed automatically. You can also set these options simply  
by pressing the SND EFFECT (Sound Effect) button.  
Item  
Setting Change  
Bass  
ൖ
0
൘
൘
൘
Adjusts low sounds  
Treble  
Balance  
ൖG 0  
Adjusts high sounds  
ൖ
0
Adjusts left and right volumes  
Note : If you change the value of the Bass, Treble, and Balance, the User  
is selected automatically.  
Auto Volume Level  
5. Select Auto Volume Level using the ̵/̷ button and press the ൖGor ൘ button  
to select On or Off.  
Note : Auto Volume Level can adjust the volume every time the channel  
is changed.  
TruSurround XT  
6. Select TruSurround XT using the ̵/̷ button and press the ൖGor ൘ button  
to select On or Off.  
Note : The benefits of TruSurround XT sound are enormous. You can be  
completely enveloped in sound: just as if you were at a concert  
hall or cinema.  
Sound Source  
7. Select Sound Source using the ̵/̷Gbutton and press the ൖGor ൘ button  
to select Main or PIP/TWIN.  
Note : You can hear the sound of small screen or main screen  
according to your selecting.  
Using the Sound Button in the Remote Control  
You can use the Sound button in the remote control. Press the MUTE button  
to mute the sound. If you press again, the sound will be reactivated.  
26. Changing the Sound  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Time  
Setting the Current Time  
You can set the current time. If you wish to use the Power On or Off Time,  
you must also set the Local Time.  
1. Press the MENU button.  
2. Select System using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Time Setting using the ̵/̷ button, and press the OK or ൘Gbutton.  
4. Select Date using the ̵/̷Gbutton, and press the OK or ൘Gbutton.  
5. Press the ̵/̷/ൖ/൘Gbutton to set the current date.  
6. When you are satisfied with your choice, press the OK button to store the date.  
7. Select Local Time using the ̵/̷ button, and press the OK or ൘ button.  
8. Press the ̵/̷/ൖ/൘ button to set the current time.  
9. When you are satisfied with your choice, press the OK button  
to store the time.  
Note : The LCD-TV sets and updates the time automatically by the air,  
if you successfully search digital terrestrial channels.  
You must set the GMT Offset value in DTV Setup menu. Refer  
DTV SETUP - Preferences - Local Setting menu for more detail  
information.  
Automatically Turning the TV On and Off  
You can automatically switch on or off at the time you select.  
1. Press the MENU button.  
2. Select System using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Time Setting using the ̵/̷ button, and press the OK or ൘ button.  
4. Select Power On/Off Time using the ̵/̷ button, and press the  
GGGGൖ or ൘ button to select Enable or Disable.  
5. In the Enable mode, Select Timer using the ̵/̷ button, and press  
the OK or ൘ button.  
6. Press the ̵/̷/ൖ/൘ button to set the time.  
7. When you are satisfied with your choice, press the OK button to store the time.  
8. Select Auto Power Off using the ̵/̷Gbutton, and press the ൖ or ൘ button  
to select Enable or Disable. In setting the Auto Power Off to Enable,  
the LCD TV turns off automatically if there is no signal.  
27. Setting the Time  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Language  
1. Press the MENU button.  
2. Select System using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Language using the ̵/̷ button, and press the ൖ or ൘ button to  
select a particular language.  
OSD Transparency  
1. Press the MENU button.  
2. Select System using the ̵/̷ button, and press the OK or ൘ button.  
3. Select OSD Transparency using the ̵/̷ button, and press the ൖ or ൘ button  
to set the transparency.  
High : Medium : Low  
AV Output  
1. Press the MENU button.  
2. Select System using the ̵/̷ button, and press the OK or ൘ button.  
3. Select AV Output using the ̵/̷ button, and press the ൖ or ൘ button to  
select a particular thing.  
Digital TV : Analog TV : AV1 : AV2  
Antenna Power  
1. Press the MENU button.  
2. Select System using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Antenna Power using the ̵/̷Gbutton, and press the ൖ or ൘ button  
to select On or Off.  
Aspect Ratio  
You can select the picture format you prefer.  
1. Press the MENU button.  
2. Select System using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Aspect Ratio using the ̵/̷Gbutton, and press the ൖ or ൘ button  
to select a particular thing. You can also set the Aspect Ratio simply  
by pressing the ASPECT RATIO button.  
_ Auto  
: The screen format will automatically become enlarged,  
allowing you to view the picture at its maximum size.  
_ 4:3 , 14:9 , 16:9 : Setting for the 4:3, 14:9, or 16:9 screen format.  
_ Zoom1, Zoom2 : Expansion to the Zoom1 or Zoom2 ratio.  
Note : If you wish to change the Aspect Ratio, you must set the PIP/TWIN  
mode to Off. To enlarges the picture to the wide aspect ratio in the  
Digital TV mode, press the WIDE button. Although the channel is  
changed, the wide aspect ratio keeps.  
Backlight Brightness  
1. Press the MENU button.  
2. Select System using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Backlight Brightness using the ̵/̷ button, and press the ൖ or ൘ button  
to set the brightness of LCD panel.  
High : Medium : Low  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Displaying the Teletext Information  
You can display Teletext information at any time on your TV.  
Most TV channels broadcast information via teletext. Each channel which broadcasts  
teletext transmits a page with information on how to use its teletext system.  
Depending on the TV channel, teletext is transmitted in different systems. The colours  
used in the options line correspond with the colour buttons of your remote control.  
For Teletext information to be displayed correctly, channel reception must be  
stable, otherwise:  
+ Information may be missing  
+ Some pages may not be displayed  
Press the TELETEXT (  
) button to display teletext.  
And you can control the Teletext functions using the following buttons.  
NR-103  
Special Teletext Functions  
TELETEXT  
MIX  
Activate/Deactivate the teletext service.  
Displays the teletext with the broadcasting screen.  
Displays the teletext index page.  
INDEX  
UPDATE  
Display the TV picture on the screen while waiting  
for the new teletext page.  
REVEAL  
MODE  
Displays the concealed information.  
Displays the mode.  
SIZE  
Displays the text size as double size.  
Hold function during teletext display.  
Search the sub-page using the sub-code.  
HOLD  
SUBPAGE  
You are in teletext mode, so only teletext functions are available.  
29. Displaying the Teletext Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the PC Input  
PC INPUT  
1. Press the TV/AV button to switch to PC mode.  
2. Select PC using the ̵/̷ button, and press the OK button.  
3. Press the MENU button.  
4. Select PC Input Setting using the ̵/̷ button, and press the OK or ൘ button.  
5. Select the following item using the ̵/̷ button, and press the OK orG൘ button.  
_ Auto Configure : Automatically optimizes the status of screen.  
This is recommended when connecting a new PC.  
_ Position  
_ Clock  
: Move the screen to the right, left, bottom or Up.  
: Adjusts the horizontal size of screen by increasing or  
decreasing the number of pixels.  
_ Phase  
: Sets the focus of screen.  
30. Setting the PC Input  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
Instant Recording  
Since the LCD-TV has a hard disk drive inside, you can record a programme with  
out an external media device such as a VCR.  
1. Press the RECORD (  
) button on the remote control to record the  
current programme instantly.  
2. You can change the recording duration time by pressing the RECORD (  
button repeatedly.  
)
30min -> 60min -> 90min -> 120min -> 240min -> 24hr Max  
3. To stop the recording, press the STOP (  
) button. If there is no time delay  
NR-103  
while recording a programme, it will stop recording and return to the live  
broadcasting instantly. Otherwise, if there is a time delay, it will jump to the  
current point and return to the live broadcasting by pressing the STOP (  
button once again.  
)
Note :  
_ When beginning the recording, REC (  
) icon is displayed on the  
upper right-hand side of the screen for about 3 seconds.  
_ You can reset the recording time while recording.  
_ Ensure that there is enough free space before recording, because if  
the free space on the hard disk drive is insufficient, recording will stop.  
Recording 1 hour of programme may require up to about 1GB of free  
space of hard disk space. The space for recording 1 hour of programme may  
be different depending on the programme recorded and the recorded quality.  
_ It is possible that you may not record the scrambled programme or  
data programme normally.  
_ You cannot change to other channel during recording analogue channel  
or scrambled digital programme.  
_ Recording is not available in Component, DVI or PC Input sources.  
_ You can change to other input source during recording  
_ You can playback the recorded programme during recording using  
trick play functions (FF, RW, Instant Replay, Repeat between A and  
B, Bookmark List and Add Bookmark). See the Playback Control.  
_ When you are recording the channel which is watching currently,  
the subtitle is recorded according to subtitle-setting in start of  
recording. When you are recording the channel which is not watching  
currently, the subtitle is recorded according to subtitle-setting in Menu  
(DTV SETUP - Preferences - Local Setting - Subtitle Language/Display).  
31. Recording  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
Setting the Recording Quality  
1. Press the MENU button.  
2. Select Recording using the ̵/̷Gbutton, and press the OK or ൘ button.  
3. Select Recording Quality using the ̵/̷Gbutton, and press the ൖGor ൘ button  
to select a particular thing.  
HQ (High Quality) : SP (Standard Play) : LP (Long Play)  
Decreasing the record quality decreases the amount of disk space required  
to store the images, due to a higher compression scheme.  
32. Recording  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
Recording Reservation  
You can reserve recording to record your desired programme automatically.  
You can reserve recording of a programme using Menu - Recording  
- Recording Schedule.  
Adding Recording Reservations  
1. Press the MENU button.  
2. Select Recording using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Recording Schedule using the ̵/̷ button, and press the  
OK or ൘ button.  
4. Select a blank list using the ̵/̷ button, and press the OK button  
to add a new recording schedule.  
5. Select Channel using the ̵/̷ button, and press the OK or ൘ button to  
change the channel. Change the Input source and channel No. using the  
GGGG̵/̷/ൖ/൘/NUMERICAL(0~9) button. Press the OK to save the changed channel.  
6. Select Date using the ̵/̷ button, and press the OK or ൘ button to change  
the date. Change the date using the ̵/̷/ൖ/൘/ NUMERICAL (0~9) button  
and press OK to save the changed date.  
7. Select Start Time using the ̵/̷Gbutton, and press the OK or ൘ button to change  
the start time. Change the start time using the ̵/̷/ൖ/൘/ NUMERICAL(0~9)  
button and press OK to save the changed start time.  
8. Select Duration using the ̵/̷ button, and press the OK or ൘ button  
to change the recording duration. Change the recording duration using  
the ̵/̷/ൖ/൘/NUMERICAL(0~9) button and press OK to save the  
changed recording duration. (2 min ~ 24 hours)  
9. Select Repeat using the ̵/̷ button, and select one among Once (  
Daily ( ) and Weekly ( ) using the ൖV൘ button.  
),  
10. Select Title using the ̵/̷ button, and press the OK or ൘ button to  
display a keyboard on the screen. Enter the desired title on the screen  
keyboard using the ̵/̷/ൖ/൘Gbutton.  
11. Select Recording Quality using the ̵/̷ button, and select one among  
HQ (High Quality), SP (Standard Play) and LP (Long Play) using the ൖV൘  
button.  
12. Select Save and press the OK button to complete the editing.  
13. Select Delete and press the OK button to delete the editing.  
14. Select Cancel and press the OK button to cancel the editing.  
In Recording Schedule, you can move easily to the Recorded  
Programmes or HDD Control using the RED or GREEN buttons  
on the remote control.  
33. Recording  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
Editing Recording Reservations  
1. Press the MENU button.  
2. Select Recording using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Recording Schedule using the ̵/̷ button, and press the OK or ൘ button.  
4. Select a reserved item which you want to edit using the ̵/̷Gbutton,  
and press the OK button.  
5. The next editing procedure is the same as Adding recording reservations.  
When the reserved start time comes, the following message will be  
displayed on the screen ;  
If you select Yes and press OK button, the recording of the reserved  
programme is started.  
Note :  
_ If the reserved start time comes in the standby mode, no sooner  
have you turn on the LCD-TV than the confirm message will be displayed  
on the screen.  
_ If the programme to reserve overlaps with the existing one, adjust  
the reservation so as not to overlap.  
_ If you want to stop on recording, press the STOP (  
) button.  
_ When you are recording the channel which is watching currently,  
the subtitle is recorded according to subtitle-setting in start of  
recording. When you are recording the channel which is not watching  
currently, the subtitle is recorded according to subtitle-setting in Menu  
(DTV SETUP - Preferences - Local Setting - Subtitle Language/Display).  
34. Recording  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
Time Shifted Recording  
This LCD-TV automatically saves the programme on air in the installed hard disk  
drive temporarily, so that users can watch programmes as they watch a video tape  
using functions such as rewind, fast forward, instant replay and pause.  
1. On watching TV, press the TSR on the remote control until when Time Shift On  
message appears, and the time shifted recording will be started.  
_ If you press the TSR button on watching TV, the current state of time  
shifted recording will be displayed with a message (Time Shift On or  
Time Shift Off). If you press it once again, the message will be changed  
to the other state.  
_ On the channel during time shifted recording, if you press the OK button,  
TSR On message is shown.  
Note : If you press the PLAY/PAUSE (  
) button on the Time Shift  
Off state, it will be switched to the Time Shift On automatically  
and start the time shifted recording.  
2. During time shifted recording, you can press the various playback buttons such  
as PLAY/PAUSE (  
REPLAY ( ) to playback the recording data saved temporarily in TSR buffer  
of the programme you are watching.  
), FORWARD (  
), REWIND (  
) or INSTANT  
Note :  
_ You cannot perform Repeat A-B (  
function during time shifted recording.  
) or Bookmark (  
,
)
_ If you want to playback the programme which is viewing-restricted  
or locked, will need the password.  
3. If you press a playback button, the TSR time bar will be displayed as following and  
the data will be played according to each playback function. For more information  
of the playback buttons, refer to Playback Control.  
TSR Time Bar  
TSR time bar displays the current operation status for playback of TSR data.  
1
6
2
3
4
5
7
8
1. Start time of TSR time bar  
2. Watching point  
3. Live or broadcasting point  
4. Total amount of programme saved to TSR buffer (max 30 minutes)  
5. End time of TSR time bar  
6. Play status (The speed is shown in playing of fast-forward, fast-rewind,  
slow-forward, slow-rewind.)  
7. The time of watching point  
8. Current time (The time of live or broadcasting point)  
When the play status is PLAY or LIVE on TSR time bar, if you take no action  
for about 3 seconds, TSR time bar will disappear.  
35. Recording  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
4. If you press the STOP (  
the playback will be stopped.  
) button, the TSR time bar will disappear and  
5. To stop the time shifted recording, press the TSR button until  
when Time Shift Off message appears.  
Note :  
_ It is possible that you may not record the scrambled programme  
or data programme normally.  
_ Total TSR buffer is limited.  
_ During the TSR playback or Programme Playback, the TruSurround XT  
and Auto Volume Level menus are disabled.  
36 . Recording  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback  
Programme Playback  
You can watch the recorded programme by selecting a desired  
programme in the Menu - Recording - Recorded Programmes  
and pressing the OK or PLAY/PAUSE (  
) button.  
1. Press the MENU button.  
2. Select Recording using the ̵/̷ button, and press the OK or ൘ button.  
3. Select Recorded Programmes using the ̵/̷ button, and press the  
OK or ൘ button to display the recorded programme list.  
4. Select a desired programme to playback using the ൖV൘ button, and then  
press the OK or PLAY/PAUSE (  
) button to playback the programme.  
5. Time bar appears as following and starts playback of the selected programme  
instantly.  
Time Bar  
Time bar displays the current operation status.  
1
6
2
3
4
5
7
8
9
1. The playing time of watching point  
2. The played amount of programme  
3. Watching point  
4. The non-played amount of programme  
5. The total recorded time of programme  
6. Play status (The speed is shown in playing of fast-forward, fast-rewind,  
slow-forward, slow-rewind.)  
7. Input source mode of the recorded programme (Digital, Analog, AV1/2/3,  
S-Video)  
8. Channel number  
9. Programme name  
When the play status is PLAY on Time bar, if you take no action for  
about 3 seconds, Time bar will disappear.  
6. You can perform trick play functions like VCR functions such as rewind,  
forward, slow motion, pause, skip, and replay using the playback control or  
the additional buttons on the remote control during playback a programme.  
37. Playback  
Download from Www.Somanuals.com. All Manuals Search And Download.  
currently on recording.  
_
During the TSR playback or Programme Playback, the TruSurround XT  
and Auto Volume Level menus are disabled.  
38.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback  
Editing Recorded Programmes  
Select Menu - Recording - Recorded Programmes, and then select the desired  
recorded programme to edit the information of the programme.  
Editing Title  
You can edit the title of a recorded programme.  
1. Select your desired programme in the list using the ൖV൘Gbutton.  
2. Select Edit Title using the ̵/̷ button, and press the OK button  
to display a keyboard on the screen.  
3. Enter the desired programme title on the screen keyboard using the  
GGGG̵/̷/ൖ/൘ button.  
4. After finishing editing, select Save, and then press the OK button  
to complete.  
Delete File  
You can delete the recorded programme.  
1. Select your desired programme in the list using the ൖ/൘Gbutton.  
2. Select Delete File using the ̵/̷G button, and press the OK button.  
Display a message. (Do you want to delete this recorded programme?)  
3. Select Yes using the ൖ/൘ button, and then press the OK button to delete  
the file. If you don't delete the file, select No and press the OK button.  
Copy File to External Device  
You can copy the recorded programme from/to external device.  
1. Select your desired programme in the list using the ൖV൘Gbutton.  
2. Select Copy file to external device using the ̵/̷Gbutton, and press the  
OK button. Display the progressing status including copied rate,  
elapsed time and remaining time. Please wait to copy to external device  
completely.  
3. When the file copy is finished, press the OK button. If you want to  
cancel the copying, select Cancel and press the OK button.  
Note : The file format of external device must be FAT32 or Linux file  
format for copying to external device. If the file format of  
external device is mismatched to these file format, initialize the  
external device at Menu-Recording-HDD control menu.  
39. Playback  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback  
Connecting the External HDD  
You can also save/backup the recorded data to external storage device via  
USB port located on the rear of the LCD-TV. Connect a USB cable between  
an external storage device and USB port of the LCD-TV. Then, the External  
menu will be enabled.  
USB  
HDD  
Note : It may not be compatible with the TV according to the sort of  
external HDD or its case.  
40. Playback  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback  
Playback Control  
You can perform playback control using playback buttons of the  
remote controller. You can use trick play functions during instant  
recording, time shifted recording or playing recorded programme.  
PLAY/PAUSE  
If you press PLAY/PAUSE (  
) button on the remote controller on  
playing, the playing is paused. If you press PLAY/PAUSE (  
) button  
on pausing, the playing is resumed from paused point.  
Note : If you press PLAY/PAUSE (  
) button during watching TV or  
AV input, time shifted recording is started automatically.  
Rewind to Previous Scene  
Press the REWIND (  
the scene passed by. Whenever you press the REWIND (  
rewind speed increases (x2, x4, x8, x16, x24). If you press the PLAY/PAUSE  
) button, the programme is played at normal speed. If you press the  
REWIND ( ) button on the pause state, the programme is played backward  
) button on the remote controller to watch backward  
) button, the  
(
at slow speed (x1/2, x1/4, x1/8, x1/16, x1/24).  
Fast Forward to Next Scene  
Press the FORWARD (  
) button on the remote controller to fast forward  
the programme. Whenever you press the FORWARD (  
) button, the fast-  
forward speed increases (x2, x4, x8, x16, x24). If you press the PLAY/PAUSE  
) button, the programme is played at normal speed. If you press the  
FORWARD ( ) button on the pause state, the programme is played forward  
(
at slow speed (x1/2, x1/4, x1/8, x1/16, x1/24).  
Recording  
Press the RECORD (  
) button on the remote controller to start recording the current  
programme. For more information about recording refer to Instant Recording.  
Direct Jump  
If you press the ൖGor ൘ button during playback, the moving focus appears in  
the progress bar. Move this arrow to a desired time point using the ൖV൘ button.  
Press the OK button to play the programme at the moved time point.  
To return the arrow to original play position, press the BACK button.  
41. Playback  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback  
Instant Replay  
If you press the INSTANT REPLAY (  
) button, the current programme  
is played from the 10 seconds before.  
Repeat between A and B  
You can play special section repeatedly. You can set the section by pressing the  
A-B ( ) button twice. Press the A-B ( ) button once at the desired  
starting point, and press again at the desired ending point. Then, a mark for  
the A-B section repetition will be displayed and the section is played repeatedly.  
To stop the repetition play and return to the normal play, press the A-B (  
)
button once again.  
Bookmark  
You can set bookmark where you want to save.  
Add Bookmark  
Press the ADD BOOKMARK (  
) button, when you want to save where you  
watch. No. and time of the added bookmark are shown on the screen. You can  
go to that position directly using bookmark list.  
Note : The bookmark can be saved up to 5. If you save bookmark over 5,  
the first bookmark is deleted.  
Go to Bookmark  
Press the BOOKMARK LIST (  
) button, and then the bookmark list appears.  
Select a bookmark where you want to go using the ൖV൘Gbutton, and press  
the OK button to play.  
Note : If you press the ADD BOOKMARK (  
) button on displaying  
the bookmark list, you can add the watching position to bookmark  
list instead of the selected bookmark.  
42. Playback  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDD Control  
Checking the Hard Disk Drive  
You can check the free space of the hard disk drive, and can  
format the disk drive if necessary.  
1. Press the MENU button.  
2. Select Recording using the ̵/̷ button, and press the OK or ൘ button.  
3. Select HDD Control using the ̵/̷Gbutton, and press the OK orG൘ button.  
4. Select Internal Device or External Device (if connected) using the  
GGGGൖ/൘Gbutton.  
5. You can check the total, TSR buffer, recorded and free space of each HDD.  
6. Select Diagnosis and press the OK button to diagnose the HDD.  
Diagnosing progress bar appears. After finishing diagnosing, confirm the  
message and press the OK button.  
7. Select Format and press the OK button to remove all the recorded  
programmes saved on the HDD and initialize the HDD.  
8. Select Yes and press the OK button for the format confirm message,  
and then is started formatting the HDD. Formatting progress bar appears.  
To abort formatting, select Cancel and press the OK button, and then  
select Yes and press the OK button.  
Note :  
_ You have to be careful because performing format deletes all the  
recorded programmes saved on the HDD.  
_ In case of External Device, Remount or Disconnection menu appears.  
Please connect/disconnect safety using these menus.  
_ The file format of external device must be FAT32 or Linux file format  
for copying to external device. If the file format of external device is  
mismatched to these file format, you should initialize the external  
device at Menu-Recording-HDD control menu.  
_ Don't unplug the power cord during format. If you did unplug it, you  
shoud perform the format again.  
In HDD Control, you can move easily to the Recorded Programmes or  
Recording Schedule using the RED or GREEN buttons on the remote  
control.  
43. HDD Control  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDD Control  
Connecting the External HDD  
You can also save/backup the recorded data to external storage device via USB  
port located on the rear of the LCD-TV. Connect a USB cable between an external  
storage device and USB port of the LCD-TV. Then, the External menu will be enabled.  
USB  
HDD  
Note : It may not be compatible with the TV according to the sort of  
external HDD or its case.  
44. HDD Control  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Digital TV Channel Setup  
When you purchase your LCD-TV, you can run the Automatic Search.  
It immediately performs Channel Search.(You can also run the digital TV channel  
setup in Default Setting.)  
1. Turns on the TV in the Digital TV mode.  
2. Starts the Automatic Search  
immediately. Please wait for  
finishing the Channel Search.  
If you want to stop the Channel  
Search, select the OK button.  
If the Channel Search is stopped  
or finished, press the OK button  
to save the result of the channel  
search.  
Once the channel search has  
finished, you can enjoy digital  
television.  
Warning : If you exit the Automatic Search without fully completing  
the channel searching procedure, you may not have any  
digital TV channels stored. In this case, you can use the  
Installation Menu to configure your LCD-TV as required.  
45. Digital TV Channel Setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operation  
This chapter describes functions such as switching channel, changing language,  
and basic features for watching programmes.  
Switching Channel  
You can switch the current channel using one of the following methods.  
1. Press the CH +/- button.  
2. Enter your desired channel number using the NUMERICAL (0~9) button  
to move to the channel directly.  
3. Press the DTV CH or RADIO CH button to switch between TV channel  
and Radio channel.  
Note : You can switch channel using the channel list or programme guide.  
Changing the Subtitle Language  
If the current programme provides  
Subtitle information, you can select the  
language for the Subtitle.  
1. Press the SUBTITLE button to  
display the subtitle language list.  
2. Select your desired subtitle language  
using the ̵/̷ button, and press  
the OK button. Then the subtitle  
will be displayed in the selected  
language at the bottom of the screen.  
3. Select OFF from the subtitle language list if you do not wish to display subtitles  
in the screen.  
Note :  
_ You can select a default subtitle language by selecting DTV SETUP -  
Preferences - Local Setting - Subtitle Language menu.  
_ In PIP/TWIN Input screen, the subtitle is not displayed.  
Changing an Audio Language  
If the current programme is available in  
multiple audio languages, you can select  
the language that you wish to listen in.  
1. Press the SOUNDTRACK/AUDIO  
button to display soundtrack list.  
2. Select your desired audio language  
using the ̵/̷Gand OK button  
to change the audio soundtrack.  
3. Select Audio preference(left, right,  
stereo) using the ൖ/൘ buttons.  
4. Press the EXIT or SOUNDTRACK/AUDIO button to exit the soundtrack list.  
46. Basic Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operation  
Note :  
_ you can select your desired default audio language by selecting  
DTV SETUP- Preferences - Local Setting - Audio Language menu.  
_ If the programme is broadcast in Dolby Digital one, you cannot  
set the audio preference such as left, right, and stereo.  
_ If you select Dolby Digital by selecting DTV SETUP - Preferences -  
Local Setting - Audio Priority menu, Dolby Digital soundtrack  
is automatically used in preference to the default audio language.  
Programme Information-Information Banner (I-plate)  
Programme information is always displayed for a specific period of time whenever  
you switch channels. You can view the programme information by pressing the INFO  
button twice while watching a programme. Press the EXIT button to hide the I-plate.  
General Information  
The General Information is displayed at the bottom of the screen as followings.  
1. Channel number and channel name  
2. Programme name  
3. Current time  
4. Detailed programme information : displayed if detailed programme information  
is provided.  
5. Next programme Information : displayed if next programme information is  
provided. Press the ൘Gbutton to display the next programme information.  
Note : If there is no available programme information, programme  
information is not displayed.  
47. Basic Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operation  
Detailed Programme Information  
You can see detailed information about  
the current programme.  
Press the INFO button.  
Note :  
_ Press the INFO button again  
to hide the information box.  
_ If the detailed programme  
information is more than one  
page, use ̵/̷ button to move to  
the previous or next page.  
Icons  
Represents the recommended minimum age for the current programme.  
Displayed only when the channel is a locked channel.  
Displayed only when the channel is a scrambled channel.  
Displayed only when subtitle information is available.  
Displayed only when there is any teletext information.  
Displayed only when the programme is broadcast in Dolby Digital.  
48. Basic Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel List  
Displaying and Switching Channel List  
You can display channel list using LIST button and switch to other channels  
on the channel list.  
1. Press the LIST button while  
watching a channel to display the  
channel list.  
2. Select your desired channel using  
the ̵/̷ button and press the  
OK button to change the channel.  
3. Enter the channel number directly  
using NUMERICAL (0~9) button  
to move cursor on to your desired  
channel. And then press the  
OK button to change to the  
selected channel.  
Note :  
_ Within the channel list, press the PAGE +/- buttons to move on  
page-by-page basis.  
_ Whenever you press the DTV CH or RADIO CH button while the  
channel list is displayed, the channel list will be switched  
between the TV and Radio channel list.  
Editing Channels  
You can edit all channels or each channel by channel list group.  
1. Press the DTV SETUP button.  
2. Select Edit Channels using the  
GGGG̵/̷ button, and press the  
OK or ൘Gbutton.  
3. Select Edit Channel Lists using  
the ̵/̷ button, and press the  
OK or ൘Gbutton.  
4. You will be prompted to enter your  
password. Enter your password using  
NUMERICAL (0~9) buttons.  
Note :  
_ The Default Password is 0000. If you have forgotten your Password,  
please contact your local LCD-TV distributor.  
_ Press the BACK or ൖ button to save the changes and return to  
the previous menu, press the EXIT button to exit the menu screen.  
_ You can easily navigate all menus using the assigned number for each  
menu. Press the DTV SETUP button then select the numbers 2,1 to  
select Edit Channel Lists menu.  
49. Channel List  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel List  
Select a Channel Group  
You can select the channel list group to edit TV or Radio.  
1. Press the OK or ൘Gbutton in Group  
to display channel list group.  
2. Select your desired channel list group  
using the ̵/̷ button, and press  
the OK button.  
Note :  
_ Press the DTV CH or RADIO CH button to move to TV or RADIO  
channel list directly.  
_ For editing Favourite channel list, move to DTV SETUP - Edit Channels -  
Edit Favourite Channels menu.  
Delete Channels  
You can delete one or more channels.  
1. Move the cursor to the channel list  
using the ൖ/൘Gbutton.  
2. Select your desired channel,  
and then press the OK button.  
You can select multiple channels.  
3. Select Delete in the right using  
the ൘ button, and press the  
OK button.  
50. Channel List  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel List  
Lock/Unlock Channels  
You can lock or unlock one or more  
channels.  
1. Move the cursor to the channel list  
using the ൖ/൘ button.  
2. Select your desired channel, and  
then press the OK button.  
You can select multiple channels.  
3. Select Lock in the right using  
the ൘ button, and press the  
OK button.  
Select/Unselect All Channels  
You can select/unselect all channels  
at a time.  
1. Select Select All in the right  
and press the OK button to select  
all channels.  
2. Select Unselect All in the right  
and press the OK button to unselect  
all the selected channels.  
51. Channel List  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel List  
Editing Favourite Channels  
You can edit Favourite channel or Favourite channel list.  
1. Press the DTV SETUP button.  
2. Select Edit Channels using  
the ̵/̷ button, and press the  
OK button.  
3. Select Edit Favourite Channels  
using the ̵/̷Gbutton, and press  
the OK or ൘ button.  
4. Select a channel using the  
GGGG̵/̷ button, and press the  
OK button. The selected channel  
is moved into the Favourite.  
5. Move between TV and Favourite using the ൖ/൘Gbutton. In this way,  
you can return the channel.  
Note :  
_ Press the DTV CH or RADIO CH button to move to TV or RADIO  
channel list directly.  
_ Press the BACK or ൖ button to save the changes and return to  
the previous menu. Press the EXIT button to exit the Menu screen.  
52. Channel List  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programme Guide  
The Programme Guide displays programme information about each channel,  
based on the date and time. You can also schedule your recording using  
the information given.  
Note : Press the GUIDE button to exit the Guide screen.  
Viewing Programme Guide Information  
You can view programme information for all channels.  
1. Press the GUIDE button.  
2. Move to previous or next programme  
within the same channel using the  
ൖ/൘ button.  
3. Move to other desired channel using  
GGGG̵/̷ button. If there are multiple  
channels, use PAGE +/- button  
to move to channels by page. Also,  
you can enter your desired channel  
number using the NUMERICAL (0~9)  
buttons on the remote control to  
move to the channel directly.  
4. Select your desired programme, and press the OK button.  
Then you can watch the programme if it is on air, or you can reserve it  
if it is the future programme.  
5. Press the INFO button in the selected programme to view  
Extended Information for the selected programme.  
Viewing Guide Information by Another Group  
You can view programme information for desired channel list by groups.  
1. Press the GUIDE button.  
2. Press the RED button to change the channel list group or press the  
DTV CH, RADIO CH, or FAV CH buttons.  
3. The Programme Guide for selected channel list is displayed.  
Note : Press the DTV CH or RADIO CH button to move to TV or  
RADIO channel list directly.  
53. Programme Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programme Guide  
Viewing Programme Information Using Time Bar  
You can quickly search for your desired time slot using the Time bar.  
1. Press the GUIDE button.  
2. Press the GREEN button to display  
the Time Bar.  
G
3. Select the each button using the  
GGGGൖ/൘ button, and press the  
OK button to move as your desired  
amount of time. If you press the  
button repeatedly, the same  
operation is repeated.  
4. Each button functions as follows.  
Now : Moves to the current programme  
where the cursor is located.  
ൖ
൘
: Moves to the previous programme or 30 minutes before.  
: Moves to the next programme or 30 minutes after.  
: Moves to 2 hours before.  
: Moves to 2 hours after.  
ൖDay : Moves to one day before.  
Day൘ : Moves to one day after.  
5. Select  
and press the OK button to exit the Time Bar.  
Note : The guide provides programme information from the previous  
day to the next 7 days.  
Finding a Programme  
You can find your desired programme by programme name or genre.  
Finding a Programme by Programme Name  
1. Press the GUIDE button.  
2. Press the BLUE button to display  
Find screen.  
B
3. Enter the programme name directly  
using the keyboard displayed on the  
screen.  
4. When completing entering programme  
name, select the Find, and press the  
OK button.  
Note :  
_ Select ̵/̷/ൖ/൘ button and then press OK button to enter the  
programme name on the keyboard screen.  
_ If you select Previous or Next on the Keyboard displayed on the screen  
and press OK button, the keyboard layout is switched.  
54. Programme Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programme Guide  
Finding a Programme by Programme Genre  
1. Press the GUIDE button.  
B
2. Press the BLUE button to display  
Genre screen.  
3. Select By Genre and press the  
OK button to search programme  
by genre.  
4. Select your desired genre using  
GGGG̵/̷/ൖ/൘ button and press the  
OK button.  
5. If you select your desired programme  
from the Found Programme List  
screen and press the OK button,  
you can watch the programme  
if it is on air.  
Note : The Found Programme List  
may differ depending on the  
provided programme  
information.  
Adding Reservations by Guide  
You can automatically reserve to watch your desired programme.  
1. Select the scheduled programme  
and pressing the OK button.  
2. Select OK using ൖ/൘Gbutton and  
press the OK button.  
3. When reservation has been completed,  
the icon (  
) is displayed on the  
reserved programme.  
When you cancel the reservation  
1. Select the reserved programme and press the OK button.  
The message will be displayed.  
2. Select OK and press the OK button to cancel the reservation.  
Note : You can look into reservation schedule using YELLOW button  
in guide.  
55. Programme Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Preferences  
You can set censorship classification, password, time and other options to enhance  
your viewing pleasure.  
Note :  
_ Press the BACK or ൖ button to save the changes and return to  
the previous menu. Press the EXIT button to exit the Menu screen.  
_ You can easily select all menu items using the assigned numerical  
button for each menu.  
Parental Control  
You can set parental control for each programme. You can also change your password.  
1. Press the DTV SETUP button.  
2. Select the Preferences using  
the ̵/̷ button, and press the  
OK or ൘ button.  
3. Select the Parental Control using  
the ̵/̷ button, and press the  
OK or ൘Gbutton.  
4. When prompting message is  
displayed to ask Password,  
enter the Password using the  
NUMERICAL (0~9) buttons.  
Setting Censorship Classification  
Censorship Classification allows you to  
block programmes according to the age  
level you have set.  
1. Select the Censorship Classification  
using the ̵/̷ button, and press  
the OK or ൘Gbutton.  
2. Select your desired Rating value  
using the ̵/̷ button, and press  
the OK button.  
View All : All programmes can be watched because there is no age limitation.  
P (Pre-school) : This program is designed to be appropriate for pre-school children.  
C (Children's) : This program is designed to be appropriate for all children.  
G (General Audience) : This program is designed to be appropriate for all ages.  
PG (Parental Guidance Recommended) : This program contains unsuitable materials that  
parents want to prevent their children from watching.  
M (Mature Audience 15+) : Programs are blocked for children under the age of 15.  
MA (Mature Adult Audience 15+) : Programs are blocked for children under the age of 15.  
AV (Adult Audience strong violence 15+) : This program contains the strong violent contents.  
Therefore, programs are blocked for children under the age of 15.  
R (Restricted 18+) : Programs are blocked for children under the age of 18.  
Lock All : All Programmes are blocked without considering the age level.  
Note : You have to enter your password to watch the programme which  
is blocked by the age restriction.  
56. Setting the Preferences  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Preferences  
Changing Password  
You can change the current password into a new one.  
1. Select Change Password using  
the ̵/̷ button, and press the  
OK or ൘ button.  
2. Enter New Password using the  
NUMERICAL (0~9) button, and  
select OK and press OK button.  
3. Enter the New Password again to  
confirm the Verify Password, and  
select OK and press the OK button.  
Note : The Default Password is 0000. If you have forgotten your Password,  
please contact your local LCD-TV distributor.  
Local Setting  
You can set a Language for Audio, and Subtitles and set the current time.  
1. Press the DTV SETUP button.  
2. Select Preferences using the  
GGGG̵/̷ button, and press the  
OK orG൘ button.  
3. Select Local Setting using the  
GGGG̵/̷ button, and press the  
OK or ൘ button.  
Setting Current Time  
You can set the GMT Offset for the current time.  
1. Select GMT Offset using the ̵/̷ button.  
2. Press the OK or ൘Gbutton to display GMT list. GMT can be changed  
in 30 minutes / 1 hour steps.  
3. Select your GMT offset using the ̵/̷ buttons, and press the OK button.  
Note : The current time is set automatically whenever GMT Offset changes.  
The default item is Auto. If GMT Offset is Auto, the time will change  
to summer time (BST).  
57. Setting the Preferences  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Preferences  
Time Zone  
You can adjust the time by selecting Time Zone according to your location.  
1. Select the Time Zone using the ̵/̷ button.  
2. Select your desired option using the ̵/̷ button.  
NSW/ACT : VIC : QLD : SA : WA : TAS : NT  
Audio/Subtitle Language  
You can set the language for Audio and Subtitles. The default language is English.  
1. Select Audio / Subtitle Language using the ̵/̷ button.  
2. Press the OK or ൘ button to display the available Language List.  
3. Select your desired language using the ̵/̷ button, and press the OK button.  
Audio Priority  
You can select the audio priority between language and Dolby Digital.  
1. Select Audio Priority using the ̵/̷ button.  
2. Press the OK or ൘ button to display either Language or Dolby Digital.  
3. Select your desired option using the ̵/̷ button, and press the OK button.  
+ Language  
: You can watch a programme in the selected language.  
+ Dolby Digital : You can listen in Dolby Digital sound.  
Subtitle Display  
You can select whether or not to display the Subtitle automatically if provided.  
NR-103  
1. Select Subtitle Display using the ̵/̷ button.  
2. Select your desired option using the OK or ൘ button.  
+ Auto  
: Subtitles are displayed automatically in the predefined  
subtitle language.  
+ Manual : Subtitles are displayed in the language when you select  
the subtitle language by pressing the SUBTITLE button  
on the remote control.  
Subtitle Font  
You can select the Subtitle font.  
1. Select the Subtitle Font using the ̵/̷ buttons.  
2. Select your desired option using the OK or ൘ button.  
+ Variable : Uses the horizontally variable Subtitle Font.  
+ Fixed  
: Uses the fixed Subtitle Font.  
58. Setting the Preferences  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Preferences  
Miscellaneous Settings  
1. Press the DTV SETUP button.  
2. Select Preferences using the  
̵/̷ button, and press the  
OK or ൘Gbutton.  
3. Select Miscellaneous Settings  
using the ̵/̷ button, and press  
the OK or ൘Gbutton.  
i-Plate Display Time  
You can set the duration during which the Information box is to be automatically  
displayed when you switch the channel.  
1. Select i-Plate Display Time using the ̵/̷ button, and press the OK or ൘ button.  
2. Select a value between Disable, 1 ~ 20 seconds using the ̵/̷ button,  
and press the OK button.  
59. Setting the Preferences  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Automatic Search  
If your LCD-TV is connected to a suitable aerial(outdoor aerial recommended)  
you can automatically search channels without entering any other information.  
1. Press the DTV SETUP button.  
2. Select Installation using the  
GGGG̵/̷ button, and press the  
OK or ൘ button.  
3. Select Automatic Search from  
Installation menu using the  
GGGG̵/̷ button, and press the  
OK or ൘ button.  
Search  
Please wait while the LCD-TV searches for the channels, this may take a few minutes.  
1. During the automatic search  
procedure, the cursor is located at  
Stop. If you press the OK button  
during the search, the operation is  
stopped and the channels found thus  
far will be displayed.  
2. If despite successful completion of  
search operation the some or all  
channels have been not found,  
press the OK button and perform  
to reset the search operation again  
if necessary.  
3. You can delete unnecessary channels  
from the found channels. Select your  
desired channels to delete and press  
the OK button. Then select Delete  
and press the OK button.  
To delete all channels, select  
Select All to select all channels,  
select Delete, and press the  
OK button.  
4. When completing Channel Search  
and deleting unnecessary channels,  
select Save to save the changes.  
60. Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Regional Search  
You can search channels based on state, region, and location.  
1. Press the DTV SETUP button.  
2. Select Installation using the  
GGGG̵/̷ button, and press the OK or  
൘ button.  
3. Select Regional Search from  
Installation menu using the  
GGGG̵/̷ button, and press the OK or  
൘ button.  
4. Select State/Region using the  
GGGG̵/̷ button, and press the OK or  
GGGG൘ button.  
5. Select the appropriate options according to your geographical region  
using the ̵/̷ button, and press the OK button.  
6. After completing the settings, select Search, and press the OK button.  
The following procedures are the same as those for Automatic Search.  
Refer to Automatic Search.  
61. Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Manual Search  
You can search channels manually by searching parameters, if you know the  
multiplex-parameters(check with your local broadcaster).  
1. Press the DTV SETUP button.  
2. Select Installation using the  
GGGG̵/̷ button, and press the  
OK or ൘ button.  
3. Select Manual Search from  
Installation menu using the  
GGGG̵/̷ button, and press the  
OK or ൘ button.  
4. Select Channel, Frequency,  
or Network Search using the  
GGGG̵/̷ button, and press the  
OK or ൘ button.  
Channel Number  
Enter your desired frequency channel number to search. When entering frequency  
channel number, the appropriate frequency value is automatically displayed in Frequency.  
Select one of channel using the ̵/̷ button, press the OK button.  
Frequency  
Enter your desired frequency to search directly. When entering the frequency,  
the appropriate channel for the entered frequency is automatically displayed in Channel.  
Enter frequency using the NUMERICAL (0~9) button and press OK button.  
Network Search  
If specified frequency channel information and other channel information are  
provided together, the channel, which belongs to other frequency channel,  
is also searched. Select one option between Enable and Disable using  
the ൘ button.  
62. Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Default Setting  
Default Setting restores the LCD-TV to the default settings  
Warning : Please Note that once you perform Default Setting, all data  
such as Aerial Setting information Channel List, and User  
Configured data are deleted.  
To perform Factory Default:  
1. Press the DTV SETUP button.  
2. Select Installation using the  
̵/̷ button, and press the  
OK or ൘ button.  
3. Select Default Setting using  
the ̵/̷Gbutton, press the  
OK or ൘ button.  
4. Select Yes and press the OK button  
to restore all setting to Factory  
Default. Select No and press the OK  
or BACK button to return to the previous menu.  
5. Confirm again to start loading default setting. Enter Password using the  
NUMERICAL (0~9) buttons to confirm that you wish to restore the default  
settings.  
6. When default setting is completed, Installation Wizard is automatically  
displayed, which helps Channel Search. For detailed information about  
Installation Wizard, refer to Digital TV Channel Setup.  
Note : In the Default Setting, you need a Password to enter. The Default  
Password is 0000. If you have forgotten your Password, please  
contact your local LCD-TV distributor.  
63. Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Information  
You can view all system information, and signal detection.  
1. Press the DTV SETUP button.  
2. Select System using the ̵/̷ button,  
and press the OK or ൘ button.  
Status  
You can view the System information  
1. Select Status using the ̵/̷ button,  
and press the OK or ൘ button.  
2. Confirm the information about  
Hardware version,  
Software version, Loader version,  
System ID, and Update Date.  
Signal Detection  
You can view the signal strength and signal quality reception for the channel  
that is currently being viewed.  
1. Select Signal Detection using  
the ̵/̷ button, and press the  
OK or ൘ button.  
2. Display information about the aerial  
and multiplex, which current channel  
belongs to and the graphs and  
percentage of Signal Strength and  
Quality of the channel.  
64. System Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Information  
Common Interface  
You can view the current status of the CI module.  
1. Select Common Interface using  
the ̵/̷ button, and press the  
OK or ൘ button.  
2. Select Slot 1, and press the  
OK or ൘ button.  
3. If Common Interface is available,  
you can view information about  
each Slot.  
Note : The displayed information  
about each Common Interface may differ depending on  
Common Interface type.  
Game  
This LCD-TV provides various games for user's entertainment.  
1. Press the DTV SETUP button.  
2. Select Games using the ̵/̷ button, and press the OK or ൘ button.  
3. According to the instruction displayed on screen, you can enjoy the game  
usingGൖ/൘ and OK button.  
Note : Press the EXIT or BACK button to exit the game.  
65. System Information / Game  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software Upgrade  
In order to maintain proper performance of this LCD-TV, it is essential to have  
the most up-to-date software. The latest news and release of software versions  
may be found at the HUMAX website (http://www.humaxdigital.com.).  
It is recommended that you periodically check for the availability of software update.  
Software Update from PC  
You can connect your LCD-TV to the PC directly and update your software by  
transferring the new software from the PC. Follow these steps to download new  
software from a PC to this LCD-TV.  
1. Download new software file(HDF) suitable for this LCD-TV model from our  
website into your computer (http://www.humaxdigital.com).  
2. Download and install download tool from our website into your computer.  
3. Connect your PC to this LCD-TV with an RS-232C serial cable(not supplied).  
4. Execute installed download tool, and then follow the instructions contained  
within the download tool.  
5. Reconnect the power cable of the LCD-TV and press the STANDBY button  
to start download.  
You can also start download using only the STANDBY button.  
Switch off the LCD-TV by pressing the STANDBY button and press again  
the STANDBY button after about 1 minute.  
RS-232C  
66. Software Upgrade  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Map  
LCD TV Menu  
Mode  
Brightness  
Contrast  
Picture  
Sound  
Sharpness  
Colour  
Colour Temperature  
PIP/TWIN  
Effect  
Bass  
Treble  
Balance  
Auto Volume Level  
TruSurround XT  
Sound Source  
Auto Programme  
Manual Programme  
Edit Programme  
Analogue TV  
Digital TV  
Channel  
Setup Digital  
Channel  
Recorded Programmes  
Recording Schedule  
HDD Control  
Recording  
Recording Quality  
Language  
Time Setting  
OSD Transparency  
AV Output  
System  
Antenna Power  
Aspect Ratio  
Backlight Brightness  
PC Main Menu  
Auto Configure  
Position  
Clock  
PC Input  
Setting  
Phase  
67. Menu Map  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Map  
Digital TV MENU  
Parental Control  
Local Setting  
Preferences  
Miscellaneous Settings  
Edit Channel Lists  
Edit Channels  
Edit Favourite Channels  
Automatic Search  
Regional Search  
Manual Search  
Default Setting  
Installation  
Status  
Signal Detection  
Common Interface  
System  
Games  
68. Menu Map  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Troubleshooting  
Before contacting your local service dealer, please make sure you refer to the  
following guide. If the LCD-TV does not work normally after completing the  
following trouble shooting, please contact your local LCD-TV distributor or  
service centre.  
1. No message is displayed on the front panel or the LCD-TV has no power  
+ Check the main power cable and check that it is plugged into a suitable power outlet.  
+ Check whether the Power Switch is On.  
2. No picture  
+ Make sure that the LCD-TV is in Operation Mode.  
+ Make sure that the AV Cable(SCART, SVHS, etc) is firmly connected to the LCD-TV.  
+ Make sure that the aerial is correctly connected to the equipment.  
+ Make sure that the aerial Setting is correct.  
+ Check the brightness level of the LCD-TV.  
+ Check the channel is on air.  
3. Poor picture & sound quality  
+ Install aerial make sure to avoid putting mobile phone or mircrowave oven near  
around the equipment.  
+ Use 75 ˟ coaxial cable to connecting LCD-TV and aerial.  
4. No or poor sound  
+ Check the volume level of the LCD-TV.  
+ Check the Mute status of the LCD-TV.  
+ Press the Audio button to change the Sound Track type.  
5. Remote Control does not operate  
+ To manipulate the equipment with Remote Control, the remote control's emitting  
part should be pointed directly towards the receiving part of LCD-TV's remote sensor.  
+ Check the battery of remote control.  
69. Troubleshooting  
Download from Www.Somanuals.com. All Manuals Search And Download.  
s
Error message  
Possible causes  
What to do  
No or bad signal  
+ The aerial is not  
installed correctly.  
+ Adjust aerial.  
+ Check the cable from  
the aerial. If you cannot  
resolve the problem you  
may need to have your  
aerial and installation  
tested by a professional.  
The channel is  
scrambled or not  
available.  
+ The channel has a signal  
but no audio or video.  
+ Confirm if the channel  
is currently on air.  
+ The channel is for data  
broadcasting.  
+ You cannot watch the  
channel in the usual way.  
The channel is  
scrambled.  
+ This digital terrestrial  
receiver does not support  
the service that enables  
descrambling of the  
+ Please contact your local  
dealer for an appropriate CI  
Module and viewing card.  
scrambled channels.  
The audio is not  
available.  
+ The channel has signal,  
but no Audio.  
+ Press the DTV / AUDIO  
button to confirm if the  
channel has Audio.  
The fan is out of  
control:  
+ The fan is out of order.  
+ Please turn it off.  
*Contact the call center  
immediately.  
please turn it off.  
70. Troubleshooting  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Error Message  
Problem  
Check item  
No picture on  
screen and No  
sound from  
speakers.  
+ Insert the AC power cord plug securely in AC power outlet.  
+ Make sure the remote control is not in the standby mode  
(The POWER/Standby indicator is Orange colour.)  
+ Turn on the MAIN POWER button on the bottom of the display.  
No picture /  
+ Check the brightness setting of the display.  
+ Lamp may have malfunctioned.  
No picture from  
AV terminal.  
+ Check the cable from the VIDEO INPUT terminal.  
Picture is  
+ Check the sound setting.  
displayed, But no  
sound from the  
Speakers.  
+ Make sure the sound is not muted.  
+ Make sure headphones are not connected.  
+ Check the setting of AV OUTPUT terminal.  
Picture is too light.  
Picture is too dark.  
+ Check the COLOUR and CONTRAST settings.  
+ Make sure the BRIGHTNESS setting is not set too low.  
Remote controller  
does not work.  
+ Change the batteries.  
+ Make sure the LCD-TV remote sensor is not facing a strong  
light source.  
The picture is not  
sharp.  
+ The reception may be weak.  
+ The quality of the broadcast may also be poor.  
+ Make sure the aerial is facing the right direction.  
+ Make sure the outside aerial is not disconnected.  
The picture moves.  
The picture is  
+ Make sure the antenna is facing the right direction.  
double or tripled.  
+ The signal may be reflected from mountains or buildings.  
+ There may be interference from cars, trains, high voltage  
lines, neon lights, etc.  
The picture is  
spotted.  
+ There may be interference between the aerial cable and  
power cable.  
+ Try positioning them further apart.  
+ Is the unit receiving interference from other devices ?  
+ Transmission antennas of radio broadcasting stations and  
transmission antenna of amateur radios and cellular phones  
may also cause interference.  
There are strips  
on the screen or  
colours fade.  
+ Use the unit as far apart as possible from devices that may cause  
possible interference.  
71. Troubleshooting  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification  
Specification  
Item  
Specification  
+ Type  
- Colour active matrix TFT-LCD  
- 32.0" (697.7 (W) X 392.2 (H) mm)  
- 16.7 M  
+
+
+
+
+
+
+
+
+
+
+
Display Area  
Display Colour  
Pixel Pitch  
- 0.51075 x 0.51075 mm  
- 1280 x 768 pixels  
Max. Resolution  
Interface  
LCD Panel  
- LVDS Interface with 1 pixel / clock  
- R/L : 176 , U/D : 176 (CR˻10)  
- 600:1 (Typ)  
Viewing Angle  
Contrast Ratio  
Brightness  
- 500 cd/m2 (Typ)  
Horizontal Frequency  
Vertical Frequency  
Dimension  
- 47.4 kHz (Typ)  
- 60 Hz (Typ)  
- 760.0 (H) x 450.0 (V) x 48.0 (D) mm (Typ)  
+
+
+
+
Sync  
- Separate  
Horizontal Frequency  
Vertical Frequency  
Max. Resolution  
- 31~61kHz  
PC Monitor  
- 56~75Hz  
- 1280 x 768 pixels @ 60Hz  
+
Video Input  
-
Analog Tuner(1), Digital Tuner(2), RCA(3), RGB, S-Video, Component, DVI  
+ Video Output  
- RCA  
Input /  
Output  
+
+
+
Audio Input  
- PC Audio, Component (R / L), RCA (R / L) x 3  
- S/PDIF, Speaker, Headphone, RCA (R / L)  
- RS-232C (for S/W Upgrade), USB 2.0 (for PVR)  
Audio Output  
Data Interface  
Analogue  
- EU  
Digital  
+
+
+
+
+
+
Area  
- EU  
Antenna Input  
Tuning System  
Colour System  
Sound System  
VHF Low  
- IEC 169-2 Female  
- FS  
- IEC 169-2 Female  
- OFDM DVB-T  
- BG, I, DK  
- BG, I, DK  
TV Signal  
- NICAM, A2  
- 48.25 ~ 158MHz  
- 160 ~ 442MHz  
- 442 ~ 863.25MHz  
- Yes  
- MPEG1 Layer 1/2  
- 51MHz ~ 858MHz  
+ VHF alta  
+ UHF  
+
+
Teletext  
Safety  
- Yes  
- CE  
- CE  
Regulation  
Others  
+ EMI  
+
+
+
+
+
+
Power  
- 160.5 W (~ 1.90A , Max)  
- 7W x 2EA  
Speaker Output  
Plug & Play Level  
Weight  
- DDC 1/2B  
- NET 25.0Kg / Gross 31.0Kg  
- AC 100 ~ 240V, 50/60Hz  
- 40G  
Power Supply  
HDD  
72. Specification  
Download from Www.Somanuals.com. All Manuals Search And Download.  
73.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service and Support  
You can get information such as a troubleshooting guide, software upgrades and  
product support guide from the following web sites and call center (Hotline).  
Please try to contact to your local dealers first when you have any problem.  
Web site and e-mail  
Homepage  
http://www.humaxdigital.com  
http://www.humaxdigital.com  
http://www.humaxarabia.com  
(English)  
(Deutsch)  
(Arabic)  
HCSA (Humax Customer Service Area)  
Software Download, Information and Technical Q&A  
http://www.humaxdigital.com / hcsa  
(English)  
http://www.humaxdigital.com /Deutsch / hcsa  
(Deutsch)  
E-mail (Technical Q&A)  
tech-info@humax-digital.co.uk  
techinfo@humax-digital.de  
(Europe & North Africa)  
(Germany)  
callcenterME@humaxdigital.com  
Webmaster@humaxdigital.com  
(Middle East)  
(Asia & Other area)  
Call Center  
HUMAX Hotline (United Kingdom)  
Tel : 0870 247 8800  
Fax : +44 2891 812 932  
E-mail: uksupport@humax-digital.co.uk  
Open : Local Time in UK (GMT+0)  
08:30~18:00 (Monday - Friday)  
Support Language : English  
HUMAX Hotline (Germany)  
Germany: 01805 778 870 ( 0,12/Min)  
Other Countries: + 49 1805 778 870 ( 0,12/Min+ International Call Charge)  
Open: Local Time in Germany (GMT+1)  
08:00 - 20:00 (Monday - Friday)  
08:00 - 18:00 (Saturday)  
Support Language: Deutsch/English  
HUMAX Hotline (Italy)  
Tel : 899 100080  
Fax : +39 0471 543749  
E-mail : info@mediasat.com  
Open : Local Time in Italy (GMT+1)  
08:00~18:00 (Monday - Friday)  
Support Language : Italian  
For hardware repair, please refer to support website. (Homepage or HCSA)  
74. Service and Support  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LCD-TV  
Digital and Analogue  
HTVAU32TPVR_200GB  
P/N 20010-0280  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grundig Universal Remote PC CONTROL User Manual
Haier Dishwasher DW12 EBM 1S User Manual
Hamilton Beach Frozen Dessert Maker 68771 User Manual
Hamilton Beach Hot Beverage Maker 40898 User Manual
Harbor Freight Tools Picnic Table 97736 User Manual
Heat Glo LifeStyle Indoor Fireplace Dakota 42 B User Manual
Honeywell Barcode Reader MS9500 User Manual
Honeywell Marine Instruments KMA 29 User Manual
Humminbird Fish Finder 531452 1_A User Manual
Impex Home Gym MCB 880 MG User Manual