Instruction booklet
TUMBLE DRYER
Contents
GB
GB
Important information, 2
Product data, 2
English
Installation, 3-4
Where to put your dryer
Ventilation
Electrical connection
Levelling your dryer
Before you start using your dryer
Dryer description, 5
The front
The back
Control panel
Start and programmes, 6-10
Choosing a programme
Tables of Programmes
The controls
TVEL 75 Experience
Laundry, 11-12
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 13
General safety
Saving energy and respecting the environment
Maintenance and Care, 14
Switching off the electricity
Cleaning the filter after each cycle
Check the drum after each cycle
Cleaning the dryer
Troubleshooting, 15
Service, 16
Disposal
Hotpoint Guarantee, 19
Hotpoint After Sales Service, 20
! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and
should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the
dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.
! Read these instructions carefully; the following pages contain important information on installation and suggestions
on how the appliance works.
This symbol reminds you to read this booklet.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Permanent venting
Where to put your dryer
GB
In conjunction with the vent tube we recommend
using a Wall/Window Vent Kit, available at a retail
location or the nearest Spare Parts Dealer.
●
Place your dryer at a distance from gas ranges,
stoves, heaters, or cook tops because flames can
damage the appliance.
●
If you are going to install the
Minimum gap 10mm
Wall mounting
appliance under a work
1. Leave an opening in
the wall to the left of the
dryers proposed position.
2. Keep the tube as short
and straight as possible
to prevent condensed
moisture from backing up
into the dryer.
3. Similarly, the duct in
the wall should slope
downwards towards the
outside.
counter, be sure to leave a
10mm space between the
top and any other objects on
or above the machine and a
15mm space between the
sides and lateral furnishings
Minimum gaps
15mm
or walls. This is to ensure
proper air circulation. Make sure that the back
vents are not obstructed.
●
Make sure you put your dryer in an environment
that is not damp and has proper air circulation
throughout, the dryer will not operate efficiently in
an enclosed space or cupboard.
Window mounting
1. With a stacked dryer
the hole in the window
should ideally be made
below the vent.
! We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed
behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the dryer door.
2. The tube should be
kept as short as possible.
Ventilation
The Dryer dries your laundry by drawing in cool, clean
and relatively dry air, heating it, and then distributing it
through the clothes as they are gently tumbled. For
optimum performance, the moist air is then blown out
through a vent tube at the back of the dryer.
When the dryer is in use, there has to be adequate
ventilation to avoid the back flow of gases into the room
from appliances burning other fuels, including open fires.
Depending on how often you use your dryer, it is
essential that areas A and B are checked periodically
to remove lint or debris.
The vent tube adaptor must be fitted securely thus
preventing any humid air from being emitted back into
the room.
! The Dryer should not be pushed so far back that the
tube adaptor is pulled out of position or the tube is
squashed or bent.
Mobile venting
! The tube should be kept clear of the air intake vent
and kinks or ‘U’ bends must be avoided as these will
obstruct the tube or trap condensation.
A vent tube must always be fitted when the dryer is
used in conjunction with Mobile Venting.
The tube must be fitted securely into the back of the
dryer (see Dryer Description). If possible, it is always
best to connect the tube to a permanent
outlet close to the dryer. If permanent installation is
not possible, the dryer will work just as well with the
tube passing through a partly-opened window.
! Ensure that the end of the tube is not directed
toward the air intake vent at the rear of the dryer.
! The vent tube should not exceed 2.4 metres in
length and should be kept free of any possible
accumulation of fluff, lint and water by shaking it out
frequently. Always ensure that the tube is not
squashed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Open window venting
Moulded plug
GB
The end of the tube
! The plug must not be used
without the fuse cover in place. If
a replacement fuse holder/cover is
required, it must be of the same
colour coding or wording as
shown on the base of the plug.
Replacements are available from
authorised dealers.
should be directed
downwards, to prevent
warm moist air from
condensing in the room or
in the dryer.
Changing the plug
The wires in the power cord are coloured in accordance
with the following:
Green and Yellow
(Earth) wire to terminal
! Ensure that the dryer is adequately ventilated and
that the end of the vent tube is not directed towards
the air intake duct.
marked ‘E’, symbol
or coloured green and
yellow.
,
! The vent tube must always be fitted for optimum
performance.
! Make sure that the vent tube and air intake vents are
not obstructed or blocked.
! The dryer must not recycle exhaust air.
! Misusing a tumble dryer may create a fire hazard.
! Do not discharge exhaust air into a flue which is
used for exhaust fumes from other appliances that
burn gas or other fuels.
! Do not discharge exhaust air into an extraction
system or any duct with an extractor fan. This will
affect the way the thermal controls operate and can
result in a fire hazard.
13A ASTA approved
fuse to BS1362.
Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.
Brown (Live) wire to
terminal marked ‘L’ or
coloured red.
Cord clamp
! If the plug being replaced is a non-rewirable type,
then the cut-off plug must be disposed of safely. DO
NOT leave it where it can be inserted into a socket
and create a shock hazard.
! The power supply cord should be checked periodically
and replaced by a cord specially prepared for this
dryer and fitted only by authorised technicians (see
Service). New or longer power cords are supplied at
an extra charge by authorised dealers.
Electrical connections
! The manufacturer denies any responsibility should
any of these rules not be followed.
! If in doubt about any of the above consult a qualified
electrician.
Make sure of the following before you insert the plug
into the the electrical socket:
●
The socket must be grounded.
●
The socket must be able to sustain the machines
maximum power, which is indicated on the rating
label (see Dryer Description).
Levelling your dryer
The dryer must be installed level for correct operation.
When you have installed your
dryer in its final location check
that it is level first side to side,
then front to back.
●
Power voltage must be within the values indicated
on the rating label (see Dryer Description).
The socket must be compatible with the dryers
plug. Should this not be the case, replace the
plug or the socket.
●
! The dryer must not be installed outdoors, even if the
space is sheltered. It can be very dangerous if it is
exposed to rain or storms.
! Once installed, the dryers electrical wire and plug
must be within easy reach.
If the dryer is not level, use a
wooden block to
support it while adjusting the two
front legs up or down, until your
dryer is level.
! Do not use extension cords.
! The power cord must not be bent or squashed.
! The power cord supplied is fitted with a BS1363 plug
and a 13 amp BS1362 fuse. If you need to replace the
fuse, use only those rated at 13 amp (13A) and ASTA
approved to BS1362.
Before you start using your dryer
Once you have installed your dryer and before you
use it, clean the inside of the drum to remove any dust
that could have accumulated during transport.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer Description
The front
The back
GB
Drum
Model & Serial numbers
Control Panel
Air Intake Vent
Rating plate
Vent Tube fitted here
Filter
Caution: Hot!
Control panel
PROGRAMMES
Knob
START/PAUSE
Button & Light
Clean Filter
Light
Indicator
OPTION
Buttons & Lights
ON/OFF
Button
Progress or Delay
Lights
button in pauses the programme and stops the dryer.
The light is green when programme is running, flashing
amber if the programme has been paused or flashing
green if on standby waiting to start a programme (see
Start and Programmes).
Note: This light also flashes amber during the Post
Care phase of a programme.
The ON/OFF button
: If the dryer is running and
this button is pressed and held for more than 3
seconds, the dryer is turned off. Press and hold again
for more than 3 seconds and the dryer reactivates.
The PROGRAMMES knob sets the programme: rotate
it until the indicator is pointing to the programme you want
to select (see Start and Programmes).
The Progress or Delay lights show you the status of
the programme, or the delay time when they flash.
During a delayed start the lights flash to show the
delay selected. When (not flashing) they show each
stage of the programme by the corresponding light
turning on (see Start and Programmes).
The OPTION buttons/lights select available options for
your selected programme. The lights indicate that the
option has been selected. If an option is not available
the buzzer will beep three times (see Start and
Programmes).
The Clean Filter light gives you a reminder before
every programme that it is essential to clean the filter
every time the dryer is used (see Maintenance and Care).
The START/PAUSE button/light
starts a selected
programme. When you press this button there will be
one beep and the progress lights will flash to confirm
the action. When a programme is running, holding this
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Choosing a programme
while others continue drying. When you close
the door again, press the START/PAUSE button in
order to resume drying.
(When the door is opened the START/PAUSE light
will flash Amber, after the door is closed and the
START/PAUSE button pressed, the START/PAUSE
light will stop flashing and show green.)
Note: During the Post Care phase this light
flashes Amber.
GB
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
3. Open the door and make sure the filter is clean
and in place (see Maintenance).
4. Load the machine and make sure items are not in
the way of the door seal. Close the door.
5. If none of the lights are on: Press the ON/OFF
9. At the end of the drying cycle the End light comes
on and either :
button
.
6. Choose a programme by checking the Programmes
Guide (see Programmes) as well as the indications
for each type of fabric (see Laundry).
- The buzzer will beep 3 times to let you know
that your programme is complete. (Note: If
the SOUND option was selected the buzzer
beeps 3 times every 30 seconds for 5
minutes).
- Select a programme by rotating the
PROGRAMMES knob.
7. Set a delay time and other options if necessary.
8. The START/PAUSE light is flashing green:
or - If you have selected the Crease Care option
and you do not take the items out immediately,
the items will tumble occasionally for 10
hours or until you open the door, the buzzer
will then beep 3 times to confirm the
programme is completed.
- press the START/PAUSE
button to begin.
The green light stops flashing.
During the drying programme, you can check on
your laundry and take out items that are dry
10. Open the door, take the laundry out, clean the filter
and replace it (see Maintenance).
11. Unplug the dryer.
Note:
This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is detected. Press the ON/OFF button briefly and wait for the
dryer to reactivate.
Shirts Light Dry
High heat option
This is a programme for shirts made from cotton.
It can be used for load sizes up to 3kg (approximately 10 shirts).
This programme will take about 60 minutes, but may take longer depending on the size of the load and the spin
●
●
●
speed used in your washer.
Low heat option
●
This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such
as polyester and cotton.
It can be used for load sizes up to 3kg (approximately 14 shirts).
This programme will take about 55 minutes, but may take longer depending on the size of the load and the spin
●
●
speed used in your washer.
Shirts dried using this programme are usually ready to put away, the edges or seams may be slightly damp. If this is
the case, try turning the shirts inside out and running the programme again for a short period.
Jeans
●
This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.
It can be used for load sizes up to 3kg (approximately 4 pairs).
Do not mix dark and light coloured items.
It can also be used on other garments made from the same material, such as jackets.
●
●
●
●
This programme will take about 85 minutes, but may take longer depending on the size of the load and the spin
speed used in your washer.
●
Loads dried using this programme are usually ready to wear, the edges or seams may be slightly damp. If this is
the case, try turning the jeans inside out and running the programme again for a short period.
! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Wool Programme
GB
●
This is a programme for tumble dryer safe garments marked with the symbol
It can be used for load sizes up to 1kg (approximately 3 sweaters).
We recommend that garments are turned inside out before drying.
This programme will take about 60 minutes, but may take longer depending on the size and density of the load and the
spin speed used in your washer.
.
●
●
●
●
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly
damp. Allow these to dry naturally as over-drying could damage garments.
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape.
! This programme is not suitable for Acrylic garments.
Baby Delicate Programme
●
This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille)
and for drying your delicate clothes.
DO NOT dry items such as bibs and nappy pants with plastic coverings.
It can be used for load sizes up to 2kg.
This programme will take about 60 minutes, but may take longer depending on the size and density of the load
●
●
●
and the spin speed used in your washer.
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be
●
slightly damp. If this is the case, try turning items inside out and running the programme again for a short period.
Bed & Bath
●
This is a programme for Cotton Towels and sheets.
It can be used on any load size, do not overload your dryer (see Laundry).
This programme will take about 100 minutes, but may take longer depending on the the size and density of the
●
●
load and the spin speed used in your washer.
Loads dried using this programme are usually ready to use, the edges or seams may be slightly damp, especially
●
on large items. If this is the case, try opening them out and running the programme again for a short period.
Heat & Enjoy
This programme helps to heat towels & bathrobes for a warm sensation after a bath or shower. It is also useful for
warming clothes before dressing during winter. The cycle heats clothes to 37°C (Body Temperature) and runs at this
temperature for a maximum of 4 hours or until you stop the cycle by opening the door.
Maximum load 3kg.
Easy Iron Programme
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle
relaxes the fibres and makes them easier to iron and fold.
! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results: 1. Do not load more than the maximum capacity. These numbers refer to the dry weight:
Fabric
Maximum load
2.5kg
2kg
Cotton and Cotton mixtures
Synthetics
Denim
2kg
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles
and put them away in the closet. Should this not be possible repeat the programme.
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,
and less well on acrylic fibres and on materials such as Tencel®.
Refresh
! ‘Refresh’ is not a drying programme and should not be used for wet articles of clothing.
●
It can be used on any load size, but is more effective on smaller loads.
Do not overload your dryer (see Laundry).
This is a 20 minute programme that airs your clothes with cool air. Also use to cool warm clothes.
●
●
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Programmes
! If none of the lights are lit; Press the ON/OFF button
GB
and then select programme.
What it does...
How to set it...
Notes/Options available:
Programme
Dries your clothes, ready 1. Position the PROGRAMME knob on 1.
Delay Timer
Crease Care or Sound
1
Cottons
Ready to wear
for wearing.
2. Select any Options, if required.
3. Press the Start/Pause button
.
Delay Timer
High Heat
Crease Care or Sound
Dries your clothes, ready 1. Position the PROGRAMME knob on 2.
2
Cottons
Cupboard Dry
for putting away.
2. Select any Options, if required.
3. Press the Start/Pause button
.
Delay Timer
High Heat
Crease Care or Sound
Dries your clothes, ready 1. Position the PROGRAMME knob on 3.
3
Cottons
Hanger Dry
for hanging.
2. Select any Options, if required.
3. Press the Start/Pause button
.
Delay Timer
High Heat
Crease Care or Sound
Dries your clothes, ready
for ironing.
1. Position the PROGRAMME knob on 4.
2. Select any Options, if required.
4
Cottons
Iron Dry
3. Press the Start/Pause button
.
Dries your Cotton or
Synthetic shirts, ready for
putting away.
Delay Timer
High Heat
Crease Care or Sound
1. Position the PROGRAMME knob on 5.
2. Select any Options, if required.
5
Shirts
Light Dry
3. Press the Start/Pause button
.
Dries your Synthetic
clothes, ready for putting
away.
Delay Timer
Crease Care or Sound
1. Position the PROGRAMME knob on 6.
2. Select any Options, if required.
6
Synthetics
3. Press the Start/Pause button
.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
Programmes Table
! If none of the lights are on; Press the ON/OFF button
GB
and then select programme.
EXCLUSIVES
Programme
What it does...
Dries your Cotton
Jeans.
How to set it...
Notes/Options available:
Delay Timer
Crease Care or Sound
1. Position the PROGRAMME knob on 7.
2. Select any Options, if required.
3. Press the Start/Pause button
7
Jeans
1. Position the PROGRAMME knob on 8.
2. Press the Start/Pause button
Dries your Woollen
clothes, (see previous
pages).
Sound
8
Wool
Dries your clothes on
Low heat setting, ready
to be worn.
1. Position the PROGRAMME knob on 9.
2. Select any Options, if required.
3. Press the Start/Pause button
Delay Timer
Crease Care or Sound
9
Baby
Delicates
1. Position the PROGRAMME knob on 10.
2. Select any Options, if required.
3. Press the Start/Pause button
Dries your Bedding &
Towels on High Heat
setting, ready for putting
away.
Delay Timer
Crease Care or Sound
10
Bed & Bath
TIMED DRY
Programme
Notes/Options available:
What it does...
How to set it...
Always use timed drying 1. Position the PROGRAMME knob on either
Timed
Drying
Delay Timer
High Heat
Crease Care or Sound
11. for 30 minute programme
for loads of less than
1kg.
The heat setting used
depends on the fabric
that is being dried (see
laundry).
or
12. for 60 minute programme
or
13. for 140 minute programme
●
The last 10 minutes of
or
these programmes is the
cool tumble phase
2. Select any Options, if required.
3. Press the Start/Pause button
EXTRA
Programme
What it does...
Warms towels,
bathrobes or other
clothes
How to set it...
1. Position the PROGRAMME knob on 14.
2. Press the Start/Pause button
Notes/Options available:
None
14
Heat & Enjoy
Brief programme
1. Position the PROGRAMME knob on 15.
2. Press the Start/Pause button
Sound
15
Easy Iron
(approximately 10
minutes) that softens
fibres of clothing that is
ready for ironing.
! This is not a drying
programme (see previous
pages).
20-minute programme
that airs your clothes
with cool air. Use also to
cool warm clothes.
1. Position the PROGRAMME knob on 16.
2. Press the Start/Pause button
Sound
16
Refresh
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Start and Programmes
The Controls
High Heat
GB
Press this button and a high heat setting is selected and
the light next to the button comes on. If the light
alongside the button is on then pressing the button
selects a low heat setting and the light goes out.
Not all programmes allow you to change this setting.
●
PROGRAMMES knob
! Warning, if after pressing the start button, the
programmes knob position is changed, the new position
will NOT change the programme selected.
To change a selected programme, press the
Sound
Start/Pause button
, the light flashes Amber to
If selected, gives a signal at the end of the drying cycle,
to remind you that the clothes are ready to be removed.
Not available with the Heat & Enjoy programme.
Note: If you have selected the Crease Care option this
option is not available.
indicate the programme is paused. Select the new
programme and any options required, the light will
then flash green. Press the Start/Pause button
again and the new programme will start.
●
OPTION buttons / lights
●
These buttons are used to customise the selected
programme to your requirements. Not all options are
available for all programmes (see Start and
Programmes). If an option is not available and you
press the button, the buzzer will beep three times. If
the option is available the option light next to the
button lights to confirm the selection.
Door Opening
Opening the door (or pressing the Start/Pause button)
during a programme will stop the dryer and have the
following effects:
Note: The Start/Pause light flashes Amber during the
Post Care phase of a programme.
●
The Start/Pause light flashes Amber.
During a delay phase the delay will continue to
●
Progress (
Drying, Cool Tumble, End) /
count down. The Start/Pause button must be
pressed to resume the delay programme.
One of the delay lights will flash to show the
current delay setting.
Delay (3hr 6hr 9hr) Lights
When the light next to the delay button is on, these lights
flash to indicate the delay time selected. During other
programmes they indicate the progress of the dryer,
each one comes on as the corresponding phase starts.
●
The Start/Pause button must be pressed to
resume the programme. The progress lights will
change to show the current status and the
Start/Pause light will stop flashing and turn green.
Delay Timer (Time Delay)
The start of some programmes (see Start and
Programmes) can be delayed for up to 9 hours in 3hr
steps.
●
During the Post Care phase of a drying
programme, the programme will finish. Pressing
the Start/Pause button will re-start a new
programme at the beginning.
When a delayed start is in progress the light next to the
delay button will be on and the selected delay period
light will flash (after the start button has been pressed).
To set a delayed start, press the Delay Timer button,
and the light next to the button will come on together
with the 3hr delay light. Pressing the button again will
advance the delay setting to 6hr, the 3hr light goes
out and the 6hr light is on. Each time you press the
button the delay setting advances 3 hours, as indicated
by the corresponding light. If the 9hr light is on,
pressing the button again will cancel the delay.
Holding in the On/Off button will also cancel.
Crease Care
The pre-care option is only available if a delayed start has
been selected. It tumbles the clothes occasionally during
the delayed period to help prevent creases developing.
The post-care option occasionally tumbles the clothes
after the end of the drying and cool tumble cycles to
prevent creases developing, should you not be available
to remove the load immediately the programme is
complete. The End light is on during this phase. Note:
The Start/Pause light flashes Amber during this phase.
Selecting this option enables both the pre and post care
functions if appropriate.
●
Changing the programmes knob will select a new
programme and the Start/Pause light will flash
green. You can use this to select the Refresh
programme to cool the clothes, if you find them
dry enough. Press the Start/Pause button to begin
a new programme.
●
Note
If you have a power cut, switch off the power or
remove the plug, press and hold the On/Off button
until the dryer reactivates, then press the Start/Pause
button.
Note: If you have selected the Sound option this option is
not available.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Laundry
Sorting your laundry
Wash Care Labels
GB
●
Check symbols on clothing labels to make sure
that the articles can be tumble dried.
Sort laundry by fabric type.
Empty pockets and check buttons.
Close zippers and hooks and tie loose belts and
strings.
Wring out each item in order to eliminate as much
excess water as possible.
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
●
●
●
May be tumble dried
●
Do not tumble dry
! Do not load dripping wet clothes into the dryer.
Tumble dry at high heat setting
Tumble dry at low heat setting
Maximum load size
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 7kg max (15lb)
Synthetic fibres: 3kg max (6.6lb)
Items not suitable for tumble drying
●
Articles that containing rubber or rubber-like
materials or plastic film (pillows, cushions, or PVC
rainwear), any other flammable articles or objects
that contain flammable substances (towels soiled
with hair spray).
Glass fibres (certain types of draperies)
Items which have been dry cleaned
! DO NOT overload the dryer as this could result in
reduced drying performance.
Typical weights
●
●
Note: 1kg = 1000g
(1lb = 16oz)
150g
●
Items with the ITCL Code
(see Special
Clothes
clothing items). These can be cleaned with special
at-home dry cleaning products. Follow instructions
carefully.
Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads etc). These expand
when drying and would prevent airflow through
the dryer.
Blouse
Cotton
(5oz)
Other
Cotton
Other
100g
500g
350g
700g
(3oz)
Dress
(1lb 2oz)
(12oz)
(1lb 6oz)
●
Jeans
10 nappies
Shirt
1000g (2lb 3oz)
Cotton
Other
300g
200g
125g
(10oz)
(7oz)
(4oz)
T-Shirt
Household Items
Duvet cover
(Double)
Cotton
Other
1500g (3lb 5oz)
1000g (2lb 3oz)
Large Tablecloth
Small Tablecloth
Tea Towel
700g
250g
100g
700g
350g
500g
350g
(1lb 6oz)
(9oz)
(3oz)
Bath Towel
(1lb 6oz)
(12oz)
Hand Towel
Double Sheet
Single Sheet
(1lb 2oz)
(12oz)
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and synthetics together.
If this happens simply give them an additional short
period of drying.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Laundry
Special clothing items
Times are approximate and can vary depending
upon:
GB
Blankets and Bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special
care on LOW heat setting. Avoid drying for a long
period of time.
●
Amount of water retained in clothes after spin
cycle: towels and delicates retain a lot of water.
●
Fabrics: items that are the same type of fabric but
Pleated or creased garments: read the manufacturer’s
drying instructions on the garment.
different textures and thicknesses may not have
the same drying time.
●
Starched articles: do not dry these with non-starched
items. Make sure that as much of the starch solution is
removed from the load as possible before placing it in
the dryer. Do not over-dry: the starch will become
powdery and leave your clothing limp, which defeats
the purpose of starch.
Quantity of laundry: single items or small loads
may take longer to dry.
●
Dryness: If you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
●
Heat setting.
Drying times
●
Room temperature: if the room where the dryer is
The table below presents APPROXIMATE drying times
in minutes. Weights refer to dry garments:
located is cold, it will take longer for the dryer to
dry your clothes.
●
Bulk: some bulky items can be tumble dried with
Cottons
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
Full Heat (use High Heat option for Timed Drying)
Drying times 800-1000rpm in washing machine
1kg 2kg 3kg
4kg
5kg
6kg
7kg
! Do not over-dry your clothes.
All fabrics contain a little natural moisture, which
20-30 35-45 45-60 60-70 70-80 80-100 90-120
keeps them soft and fluffy.
Synthetics
Full Heat (use High Heat option for Timed Drying)
Drying times on reduced spin in washing machine
1kg
2kg
3kg
20-40
30-50
40-70
Delicates (e.g.Acrylics)
Use Timed Drying with Low Heat option
Drying times on reduced spin in washing machine
1kg
30
2kg
60
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings and Suggestions
To minimise the risk of fire in your tumble dryer, the
! The appliance has been designed and built according
to international safety standards.
These warnings are given for safety reasons and must
be followed carefully.
GB
following should be observed:
●
Tumble dry items only if they have been washed with
detergent and water, rinsed and been through the spin
cycle. It is a fire hazard to dry items that HAVE NOT
been washed with water.
●
Do not dry garments that have been treated with
General safety
chemical products.
Do not tumble dry items that have been spotted or
●
●
This tumble dryer is not intended for use by
soaked with vegetable or cooking oils, this constitutes a
fire hazard. Oil-affected items can ignite spontaneously,
especially when exposed to heat sources such as a tumble
dryer. The items become warm, causing an oxidisation
reaction with the oil, Oxidisation creates heat. If the heat
cannot escape, items can become hot enough to catch
fire. Piling, stacking or storing oil-effected items can prevent
heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics containing vegetable or
cooking oil or those that have been contaminated with
hair care products be placed in a tumble dryer they should
first be washed with extra detergent - this will reduce, but
not eliminate the hazard. The cool tumble phase should
be used to reduce the temperature of the items. They
should not be removed from the dryer and piled or
stacked while hot.
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
This tumble dryer has been designed for home,
and not professional use.
Do not touch the appliance while barefoot or with
wet hands or feet.
Unplug the machine by pulling on the plug, not
the cord.
Children must not be in proximity of the dryer
when in use. After using the dryer, turn it off and
unplug it. Keep the door closed to make sure that
children do not use it as a toy.
Children should be supervised to ensure that they
do not play with the dryer.
The appliance must be installed correctly and
have proper ventilation. The air intake vents
behind the machine, the outlet vents and the vent
tube should never be obstructed (see Installation).
Never direct the vent tube outlet towards the air
intake at the back of the machine.
Never allow the tumble dryer to recycle exhaust air.
Never use the dryer on carpeting where the pile
height would prevent air from entering the dryer
from the base.
Check to see if the dryer is empty before loading it.
The back of the dryer could become very
hot. Never touch it while in use.
Do not use the dryer unless the filter is securely
in place (see Maintenance).
Do not overload the dryer (see Laundry) for
maximum loads.
Do not load items that are dripping wet.
Carefully check all instructions on clothing labels
(see Laundry).
●
●
●
●
●
Do not tumble dry items that have previously been
cleaned in or washed in, soaked in or soiled with
●
●
petrol/gasoline, dry cleaning solvents or other flammable
or explosive substances. Highly flammable substances
commonly used in domestic environments including
cooking oil, acetone, denatured alcohol, kerosene, spot
removers, turpentine, waxes and wax removers. Ensure
these items have been washed in hot water with an extra
amount of detergent before being dried in the tumble dryer.
●
●
Do not tumble dry items containing foam rubber (also
●
●
known as latex foam), or similarly textured rubber like
materials. Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
●
Fabric softener or similar products should not be used in
●
●
a tumble dryer to eliminate the effects of static electricity
unless the practice is specifically recommended by the
manufacturer of the fabric softener product.
●
●
●
Do not tumble dry undergarments that contain metal
reinforcements eg. bras with metal reinforcing wires.
Damage to the tumble dryer can result if the metal
reinforcements come loose during drying.
●
Do not tumble dry rubber, plastic articles such as shower
●
●
caps or babies waterproof covers, polythene or paper.
●
Do not tumble dry rubber backed articles, clothes fitted
with foam rubber pads, pillows, galoshes and rubber
coated tennis shoes.
●
●
●
●
Do not tumble dry large, very bulky items.
Do not tumble dry acrylic fibres at high temperatures.
Complete each programme with its Cool Tumble Phase.
Do not turn off the dryer when there are still warm
items inside.
Clean the filter after each use (see Maintenance).
Do not allow lint to collect around the dryer.
Never climb on top of the dryer. It could result in
damage.
Always follow electrical standards and requirements
(see Installation).
Always buy original spare parts and accessories
(see Service).
●
Remove all objects from pockets, especially lighters
(risk of explosion).
! WARNING: Never stop the dryer before the end of the
drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.!
●
●
●
Saving energy and respecting the
environment
●
●
●
Wring out items to eliminate excess water before
tumble drying (if you use a washing machine first,
select a high spin cycle). Doing this will save time
and energy during drying.
●
Always dry full loads - you save energy: single
items or small loads take longer to dry.
●
Clean the filter after each use to contain energy
consumption costs (see Maintenance).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Care
Switching off the electricity
Check the drum after each cycle
GB
Unplug your dryer when not using it, when cleaning it
and during all maintenance operations.
Turn the drum manually in order to remove small items
(handkerchiefs) that could have been left behind.
Cleaning the drum
Clean the filter after each cycle
! Do not use abrasives, steel wool or stainless steel
The filter is an important part of your dryer:
cleaning agents to clean the drum.
it accumulates lint and fluff that is formed while drying.
Small items could also become trapped in the filter.
When finished drying, therefore, clean the filter by
rinsing it under running water or with your vacuum
cleaner. Should the filter become clogged up, the airflow
inside the dryer will be seriously compromised: drying
times lengthen and you will consume more energy. It
may also damage your dryer.
A coloured film may start to appear on the stainless
steel drum, this may be caused by a combination of
water and, or cleaning agents such as fabric conditioner
from the wash. This coloured film will not affect the
dryer performance.
Cleaning
The filter is found in front
of the dryer trim
●
External parts in metal or plastic and rubber parts
(see diagram).
can be cleaned with a damp cloth.
●
Periodically check the vent tube and any
permanent venting fixture to make sure that there
has been no accumulation of fluff or lint, and
remove it.
●
Remove lint that collects around the filter and the
outlet vents.
Removing the filter:
1. Pull the plastic grip of
the filter upwards (see
diagram).
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
2. Open the filter and clean the lint from
the inside.
3. Replace it correctly. Ensure the filter is fully located
flush into the tumble dryer trim.
4. Remove any lint that has built up on the inside of the
door and around the door seal.
! Do not use the dryer without replacing the filter.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
GB
Problem:
Possible causes / Solution:
●
The tumble dryer won’t start.
The plug is not plugged into the socket, or not making contact.
There has been a power failure.
The fuse has blown. Try to plug another appliance into the socket.
You are using an extension cord? Try to plug the dryer’s power cord
●
●
●
directly into the socket.
The door is not closed securely?
The PROGRAMMES knob has not been set properly (see Start and
●
●
Programmes).
●
The START/PAUSE button has not been pressed (see Start and
Programmes).
●
Drying cycle will not begin.
Its taking a long time to dry.
You have set a delayed time (see Start and Programmes).
●
The filter has not been cleaned (see Maintenance).
The correct programme has not been selected for the type of fabric you
●
are drying (see Start and Programmes).
The flexible vent tube is obstructed (see Installation).
The air intake vent is obstructed (see Installation).
The permanent ventilation flap on the storm cover is obstructed (see
●
●
●
Installation).
The items were too wet (see Laundry).
The dryer was overloaded (see Laundry).
●
●
Programme finishes and
clothes are damper than
expected.
! For safety the dryer has a maximum programme time of 3 hours. If an
automatic programme has not sensed the required final moisture in this time
the dryer will complete the programme and stop. Check the above points
and run the programme again, if the results are still damp, contact the
Service Centre (see Service).
●
The START/PAUSE light
flashes amber and all Option
lights also flash to indicate a
fault.
Try turning the dryer off and remove the plug. Then replace the plug and
turn on, if a fault is still shown when you turn the dryer back on: note the
lights that are on (not flashing) and contact the Service Centre (see
Service).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Before calling the Service Centre:
Spare Parts
GB
●
Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
If not, turn off the dryer and call the Service Centre
closest to you.
This dryer is a complex machine. Repairing it yourself
or having a non-authorised person try to repair it could
cause harm to one or more persons, could damage
the machine and could invalidate the spare parts
warranty.
●
What to tell the Service Centre:
Call an authorised technician if you experience problems
while using the machine.
●
name, address and post code.
telephone number.
the type of problem.
the date of purchase.
●
●
●
●
the appliance model (Mod.).
●
the serial number (S/N).
This information can be found on the data label inside
the door of the machine.
Recycling and Disposal Information
As part of our continued commitment to helping
the environment, we reserve the right to use
quality recycled components to keep down customer
costs and minimise material wastage.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials
they contain and reduce the impact on human health
and the environment.
●
Disposing of the packaging material: follow local
regulations, so the packaging can be recycled.
To minimise risk of injury to children, remove the
●
door and plug - then cut off mains cable, flush
with the appliance. Dispose of these parts separately
to ensure that the appliance can no longer be
plugged into a mains socket.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
This appliance conforms to the following EC Directives:
- 2006/95/EC (Low Voltage Equipment)
- 2004/108/EC (Electromagnetic Compatibility)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturers’ guarantee, which covers the cost of
breakdown repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be
defective because of either workmanship or materials, we will, at our discretion, either
repair or replace the appliance at no cost to you.
The guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
- The appliance is only used on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled or otherwise
interfered with by any person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our
property.
- The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper use, neglect or interference or as a
result of improper installation.
- Replacement of any consumable item or accessory. These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
- Replacement of any removable parts made of glass or plastic.
THE GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN
COMMERCIAL OR NON-DOMESTIC PREMISES.
Non-Domestic Usage Policy:
Indesit Company manufactures appliances for domestic use only. We understand that in
some cases our appliances are used in commercial and/or non-domestic situations. We
still provide a full 12 month manufacturers’ guarantee, provided the appliance has not been:
Accidentally damaged - Damage that occurs suddenly as a result of an unexpected and
non-deliberate external action.
Maliciously damaged - The deliberate and intentional damage to the product.
Subjected to misuse - Incorrect or careless or improper use.
Subjected to overuse - Excessive usage versus that expected of a domestically situated
appliance.
5 Year Parts Guarantee
Hotpoint also offers you a FREE 5 year parts guarantee. This additional guarantee is
conditional on you registering your appliance with us and the parts being fitted by one
of our authorised engineers. There will be a charge for our engineer’s time.
To activate the extra parts warranty on your appliance, simply call our free phone registration line on
0800 519 2102 (Republic of Ireland 1800 844 347)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
195100543. 03 N
.
10/2012 - LION fpg Four Ashes, Wolverhampton
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on
UK: 08448 226 226
Republic of Ireland: 01 230 0233
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint
Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance,
or, where necessary, to arrange for an engineer to call.
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its
working life than us - the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled
telephone advisors and 1100 fully qualified engineers on call to ensure you receive
fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number
Serial number
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that
protect and hygienically clean your appliance to keep it looking good and functioning
efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership.
To activate your FREE 5 year parts guarantee you must register your appliance with us.
Free phone UK: 0800 519 2102
Republic of Ireland: 1800 844 347
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
Indesit Company, Unit 49 Airways Industrial Estate, Dublin 17
Download from Www.Somanuals.com. All Manuals Search And Download.
|