Hyperion 1300g
General Purpose Handheld Linear Scanner
User’s Guide
™
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 Word Length: Data Bits, Stop Bits, and Parity
Continuous Illumination Mode (Manual Trigger only) .
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
To Add a Carriage Return Suffix to All Symbologies4-
Intercharacter, Interfunction, and Intermessage Delays 4-
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Getting Started
About This Manual
This User’s Guide provides installation and programming instructions for the
Hyperion 1300g. Product specifications, dimensions, warranty, and customer
support information are also included.
Honeywell bar code scanners are factory programmed for the most common
terminal and communications settings. If you need to change these settings,
programming is accomplished by scanning the bar codes in this guide.
An asterisk (*) next to an option indicates the default setting.
Unpacking the Scanner
After you open the shipping carton containing the product, take the following
steps:
•
Check for damage during shipment. Report damage immediately to the
carrier who delivered the carton.
•
•
Make sure the items in the carton match your order.
Save the shipping container for later storage or shipping.
Connecting with USB
A scanner can be connected to the USB port of a computer. The scanner emu-
lates the keyboard.
1. Connect the appropriate interface cable to the scanner first, then to the com-
puter.
2. The scanner beeps.
1 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Symbols in the back of this manual.
For additional USB programming and technical information, refer to the Honey-
Connecting with Keyboard Wedge
A scanner can be connected between the keyboard and PC as a “keyboard
wedge,” where the scanner provides data output that is similar to keyboard
entries. The following is an example of a keyboard wedge connection:
1. Turn off power and disconnect the keyboard cables from the back of the ter-
minal/computer.
2. Connect the appropriate interface cable to the scanner and to the terminal/
computer.
only if
power
supply is
included
3. Turn the terminal/computer power back on. The scanner beeps.
The unit defaults to an IBM PC AT and compatibles keyboard wedge interface
with a USA keyboard. A carriage return (CR) suffix is added to bar code data.
1 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with RS-232 Serial Port
1. Turn off power to the terminal/computer.
2. Connect the appropriate interface cable to the scanner.
only if
power
supply is
included
3. Plug the serial connector into the serial port on your computer. Tighten the
two screws to secure the connector to the port.
4. Once the scanner has been completely connected, power up the computer.
5. This interface programs 38,400 baud, 8 data bits, no parity, and 1 stop bit.
Connecting with RS485
A scanner can be connected for an IBM POS terminal interface.
1 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Connect the appropriate interface cable to the device, then to the computer.
2. Turn the terminal/computer power back on. The scanner beeps.
Reading Techniques
The scanner has a bright red aiming beam that corresponds to its horizontal
field of view. The aiming beam should be centered horizontally over the bar
code; it will not read if the aiming beam is in any other direction.
Good Technique
Bad Technique
Bad Technique
1 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
The best focus point for reading most code densities is about 5 inches (12.7 cm)
from the unit. To read a single bar code or multiple bar codes (on a page or on
an object), hold the scanner at an appropriate distance from the target, pull the
trigger, and center the aiming beam on the bar code.
Menu Bar Code Security Settings
Honeywell scanners are programmed by scanning menu bar codes or by send-
ing serial commands to the scanner. If you want to restrict the ability to scan
menu codes, you can use the Menu Bar Code Security settings. Contact Tech-
Setting Custom Defaults
You have the ability to create a set of menu commands as your own, custom
defaults. To do so, scan the Set Custom Defaults bar code below before each
menu command or sequence you want saved. If your command requires scan-
sequence will be saved to your custom defaults. Scan the Set Custom
Defaults code again before the next command you want saved to your custom
defaults.
Set Custom Defaults
You may have a series of custom settings and want to correct a single setting.
To do so, just scan the new setting to overwrite the old one. For example, if you
had previously saved the setting for Beeper Volume at Low to your custom
defaults, and decide you want the beeper volume set to High, just scan the Set
Custom Defaults bar code, then scan the Beeper Volume High menu code.
The rest of the custom defaults will remain, but the beeper volume setting will be
updated.
Resetting the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Acti-
vate Custom Defaults bar code below. This resets the scanner to the custom
default settings. If there are no custom defaults, it will reset the scanner to the
factory default settings. Any settings that have not been specified through the
custom defaults will be defaulted to the factory default settings.
Activate Custom Defaults
1 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
default settings for each of the commands (indicated by an asterisk (*) on the
programming pages).
1 - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Programming the Interface
Introduction
This chapter describes how to program your system for the desired interface.
Programming the Interface - Plug and Play
Plug and Play bar codes provide instant scanner set up for commonly used
interfaces.
Note: After you scan one of the codes, power cycle the host terminal to have
the interface in effect.
Keyboard Wedge
If you want your system programmed for an IBM PC AT and compatibles key-
board wedge interface with a USA keyboard, scan the bar code below. Key-
board wedge is the default interface.
Note: The following bar code also programs a carriage return (CR) suffix.
IBM PC AT and Compatibles with CR Suffix
Laptop Direct Connect
For most laptops, scanning the Laptop Direct Connect bar code allows opera-
tion of the scanner in parallel with the integral keyboard. The following Laptop
Direct Connect bar code selects terminal ID 03, programs a carriage return
Laptop Direct Connect
with CR suffix
2 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
RS232 Serial Port
The RS232 Interface bar code is used when connecting to the serial port of a
PC or terminal. The following RS232 Interface bar code also programs a car-
riage return (CR) and a line feed (LF) suffix, baud rate, and data format as indi-
cated below.
Option
Setting
Baud Rate
38,400 bps
Data Format
8 data bits, no parity bit, 1 stop bit
RS232 Interface
RS485
Scan one of the following “Plug and Play” codes to program the scanner for an
IBM POS terminal interface.
Note: After scanning one of these codes, you must power cycle the cash
register.
IBM Port 5B Interface
IBM Port 9B
HHBCR-1 Interface
IBM Port 17 Interface
IBM Port 9B
HHBCR-2 Interface
2 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Each bar code above also programs the following suffixes for each symbology:
Symbology Suffix
Symbology
Suffix
EAN 8
EAN 13
UPC A
UPC E
0C
16
0D
0A
Code 39
00 0A 0B
00 0D 0B
00 0A 0B
00 18 0B
Interleaved 2 of 5
Code 128 *
Code 128 **
* Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B
HHBCR-1, and IBM 4683 Port 17 Interfaces
**Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface
OPOS Mode
The following bar code configures your scanner for OPOS (OLE for Retail Point
of Sale) by modifying the following OPOS-related settings:
Option
Setting
Interface
RS232
Baud Rate
38400
RS232
Handshaking
Flow Control, No Timeout
XON/XOFF Off
ACK/NAK Off
Data Bits, Stop
Bits, and Parity
Prefix/Suffix
8 Data, 1 Stop, Parity None
Clear All Prefixes and Suffixes
Add Code ID and AIM ID Prefix
Add CR Suffix
Intercharacter
Delay
Off
Symbologies
Enable UPC-A with check digit and number system
Enable UPC-E0 with check digit
Enable EAN/JAN-8 with check digit
Enable EAN/JAN-13 with check digit
Enable Code 128
Enable Code 39
Enable OPOS with automatic disable off
2 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPOS Mode
USB IBM SurePos
Scan the following “Plug and Play” codes to program the scanner for an IBM
SurePos (USB handheld scanner) interface.
Note: After scanning the code below, you must power cycle the cash register.
USB IBM SurePos
(USB Handheld Scanner)
Interface
USB IBM SurePos
(USB Tabletop Scanner)
Interface
The bar code above also programs the following suffixes for each symbology:
Symbology
Suffix
Symbology
Suffix
EAN 8
EAN 13
UPC A
UPC E
0C
16
0D
0A
Code 39
Interleaved 2 of 5
Code 128
00 0A 0B
00 0D 0B
00 18 0B
00 0A 0B
Code 39
2 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
USB PC or Macintosh Keyboard
Scan one of the following codes to program the scanner for USB PC Keyboard
or USB Macintosh Keyboard. Scanning these codes also adds a CR and LF.
d (PC)
USB Keyboar
USB Keyboard (Mac)
USB HID POS
Scan the following code to program the scanner for USB HID POS bar code
scanners.
USB HID POS Bar Code
Scanner
USB Serial Commands
USB Serial Emulation
Scan the following code to program the scanner to emulate a regular RS232-
based COM Port. If you are using a Microsoft® Windows® PC, you will need to
driver will use the next available COM Port number. Apple® Macintosh comput-
ers recognize the scanner as a USB CDC class device and automatically uses a
class driver.
Scanning this code also adds a CR and LF.
USB Serial Emulation
Note: No extra configuration (e.g., baud rate) is necessary.
2 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
CTS/RTS Emulation
CTS/RTS Emulation On
* CTS/RTS Emulation Off
ACK/NAK Mode
ACK/NAK Mode On
* ACK/NAK Mode Off
Honeywell Bioptic Aux Port Configuration
Scan the following Plug and Play code to program the scanner for a Honeywell
bioptic scanner auxiliary port configuration. This bar code sets the baud rate to
38400 bps and the data format to 8 data bits, no parity, 1 stop bit. Character
RTS/CTS with timeout and 232 ACK/NAK are also enabled.
Honeywell Bioptic Settings
Note: If you are having unexpected results with this programming code, scan
the programming code above.
2 - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Datalogic™ Magellan Bioptic
Aux Port Configuration
Scan the following Plug and Play code to program the scanner for a Datalogic
Magellan bioptic scanner auxiliary port configuration. This bar code sets the
baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.
Datalogic Magellan Bioptic Settings
Note: If you are having unexpected results with this programming code, scan
the programming code above.
Wincor Mode A
Scan the following Plug and Play code to program the scanner for Wincor Mode
A mode. This bar code sets the baud rate to 9600 bps and the data format to 8
data bits, odd parity, 1 stop bit.
Wincor Mode A
Note: If you are having unexpected results with this programming code, scan
the programming code above.
2 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Keyboard Country Layout
Scan the appropriate country code below to program the keyboard layout for
your country or language. As a general rule, the following characters are sup-
ported, but need special care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
* United States
Albania
Arabic
Azeri (Cyrillic)
Azeri (Latin)
Belarus
Belgium
Bosnia
2 - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Keyboard Mode Options
ALT Mode
If your bar code contains special characters from the extended ASCII chart for
Note: Scan the ALT mode bar code after scanning the appropriate Keyboard
Country code.
If your keystrokes require the ALT key and 4 characters, scan the 4 Characters
bar code. The data is then output with the special character(s). Default = Off.
* Off
4 Characters
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. Default =
Regular.
Regular is used when you normally have the Caps Lock key off.
* Regular
Caps Lock is used when you normally have the Caps Lock key on.
Caps Lock
2 - 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Shift Lock is used when you normally have the Shift Lock key on (not common
to U.S. keyboards).
Shift Lock
Automatic Caps Lock is used if you change the Caps Lock key on and off.
The software tracks and reflects if you have Caps Lock on or off (AT and PS/2
only). This selection can only be used with systems that have an LED, which
notes the Caps Lock status.
Automatic Caps Lock
Autocaps via NumLock bar code should be scanned in countries (e.g., Ger-
many, France) where the Caps Lock key cannot be used to toggle Caps Lock.
The NumLock option works similarly to the regular Auotcaps, but uses the Num-
Lock key to retrieve the current state of the Caps Lock.
Autocaps via NumLock
Emulate External Keyboard should be scanned if you do not have an external
keyboard (IBM AT or equivalent).
Emulate External Keyboard
Note: After scanning the Emulate External Keyboard bar code, you must power
cycle your computer.
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes.
Control + X (Control + ASCII) Mode On: The scanner sends key combina-
tions for ASCII control characters for values 00-1F. Windows is the preferred
mode. All keyboard country codes are supported. DOS mode is a legacy
2 - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
mode, and it does not support all keyboard country codes. New users should
for CTRL+ X Values.
Windows Mode Prefix/Suffix Off: The scanner sends key combinations for
ASCII control characters for values 00-1F (refer to ASCII Conversion Chart
translate any prefix or suffix information.
Default = Control + ASCII Off
Windows Mode Control + X
Mode On
* Control + X Mode Off
DOS Mode Control + X Mode
On
Windows Mode Prefix/Suffix Off
2 - 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Numeric Keypad Mode: Sends numeric characters as if entered from a
numeric keypad. Default = Off
Numeric Keypad Mode On
* Numeric Keypad Mode Off
Automatic Direct Connect Mode: This selection can be used if you have an
IBM AT style terminal and the system is dropping characters. Default = Off
Automatic Direct
Connect Mode On
* Automatic Direct Connect
Mode Off
2 - 21
Download from Www.Somanuals.com. All Manuals Search And Download.
RS232 Modifiers
RS-232 Baud Rate
Baud Rate sends the data from the scanner to the terminal at the specified rate.
The host terminal must be set for the same baud rate as the scanner.
Default = 38,400.
300
600
1200
2400
4800
9600
19200
2 - 22
Download from Www.Somanuals.com. All Manuals Search And Download.
* 38400
57,600
115,200
RS-232 Word Length: Data Bits, Stop Bits, and Parity
Data Bits sets the word length at 7 or 8 bits of data per character. If an applica-
tion requires only ASCII Hex characters 0 through 7F decimal (text, digits, and
punctuation), select 7 data bits. For applications which require use of the full
ASCII set, select 8 data bits per character. Default = 8.
Stop Bits sets the stop bits at 1 or 2. Default = 1.
Parity provides a means of checking character bit patterns for validity.
Default = None.
Note: When using 7 Data, 1 Stop, Parity None, the host must insert at least a 1
bit delay between characters. If this is not done, a different RS232 Word
Length format must be used.
7 Data, 1 Stop, Parity None
(see note above)
7 Data, 1 Stop, Parity Even
2 - 23
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Data, 1 Stop, Parity Odd
7 Data, 2 Stop Parity None
7 Data, 2 Stop, Parity Odd
8 Data, 1 Stop, Parity Even
7 Data, 2 Stop, Parity Even
* 8 Data, 1 Stop, Parity None
8 Data, 1 Stop, Parity Odd
RS-232 Handshaking
RS232 Handshaking allows control of data transmission from the scanner using
software commands from the host device.
RTS/CTS Off: RTS/CTS is turned off so no data flow control is used, but RTS
is still active.
2 - 24
Download from Www.Somanuals.com. All Manuals Search And Download.
RTS/CTS Off, RTS Inactive: RTS/CTS is turned off so no data flow control is
used and RTS is inactive.
Flow Control, No Timeout: The scanner asserts RTS when it has data to
send, and will wait indefinitely for CTS to be asserted by the host.
Character-Based Flow Control, No Timeout: The scanner asserts RTS when
it has a character to send, and will wait indefinitely for CTS to be asserted by the
host
Two-Direction Flow Control: The scanner asserts RTS when it is OK for the
host to transmit. The host asserts CTS when it is OK for the device to transmit.
Flow Control with Timeout: The scanner asserts RTS when it has data to
asserted by the host. If the delay time expires and CTS is not asserted, the
device transmit buffer is cleared and scanning may resume.
Character-Based Flow Control with Timeout: The scanner asserts RTS
CTS is not asserted, the device transmit buffer is cleared and scanning may
resume.
CTS-Based Flow Control, No Timeout: When the host asserts CTS, scan-
ning is enabled. When CTS is not asserted, scanning is disabled.
RTS On: RTS only is on during transmission. CTS is ignored.
Default = RTS/CTS Off.
* RTS/CTS Off
RTS/CTS Off, RTS Inactive
Flow Control, No Timeout
2 - 25
Download from Www.Somanuals.com. All Manuals Search And Download.
RS232 Timeout
When using Flow Control with Timeout, you must program the length of the
delay you want to wait for CTS from the host. Set the length (in milliseconds) for
a timeout by scanning the bar code below, then setting the timeout (from 1-
65535 milliseconds) by scanning digits from the inside back cover, then scan-
ning Save. Default = 1000.
RS232 Timeout
XON/XOFF
Standard ASCII control characters can be used to tell the scanner to start send-
ing data (XON/XOFF On) or to stop sending data (XON/XOFF Off). When the
host sends the XOFF character (DC3, hex 13) to the scanner, data transmission
stops. To resume transmission, the host sends the XON character (DC1, hex
11). Data transmission continues where it left off when XOFF was sent. Default
= XON/XOFF Off.
XON/XOFF On
* XON/OFF Off
ACK/NAK
After transmitting data, the scanner waits for an ACK character (hex 06) or a
NAK character (hex 15) response from the host. If ACK is received, the commu-
nications cycle is completed and the scanner looks for more bar codes. If NAK
is received, the last set of bar code data is retransmitted and the scanner waits
2 - 27
Download from Www.Somanuals.com. All Manuals Search And Download.
for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK
On bar code below. To turn off the protocol, scan ACK/NAK Off. Default =
ACK/NAK Off.
ACK/NAK On
* ACK/NAK Off
Scanner to Bioptic Communication
The following settings are used to set up communication between Honeywell
scanners and bioptic scanners.
Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout
further information.
Scanner-Bioptic Packet Mode
Packet Mode On must be scanned to set the scanner’s format so it is compati-
ble with a bioptic scanner. Default = Packet Mode Off.
* Packet Mode Off
Packet Mode On
2 - 28
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Input/Output Settings
Good Read Indicators
Beeper – Good Read
The beeper may be programmed On or Off in response to a good read. Turning
this option off, only turns off the beeper response to a good read indication. All
error and menu beeps are still audible. Default = On.
* On
Off
Beeper Volume – Good Read
The beeper volume codes modify the volume of the beep the scanner emits on
a good read. Default = High.
Low
Medium
*High
Off
3 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Beeper Pitch – Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scanner
emits on a good read. Default = Medium
Low (1600 Hz)
* Medium (2750 Hz)
High (4200 Hz)
Beeper Duration – Good Read
The beeper duration codes modify the length of the beep the scanner emits on
a good read. Default = Normal.
* Normal Beep
Short Beep
3 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Beeper Pitch – Error
The beeper pitch codes modify the pitch (frequency) of the sound the scanner
emits when there is a bad read or error. Default = 100 Hz.
* Razz (100 Hz)
* Medium (2000 Hz)
High (4200 Hz)
LED – Good Read
The LED indicator can be programmed On or Off in response to a good read.
Default = On.
* On
Off
Number of Beeps – Good Read
The number of beeps of a good read can be programmed from 1 - 9. The same
number of beeps will be applied to the beeper and LED in response to a good
read. For example, if you program this option to have five beeps, there will be
five beeps and five LED flashes in response to a good read. The beeps and
3 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
LED flashes are in sync with one another. To change the number of beeps,
scan the bar code below and then scan a digit (1-9) bar code and the Save bar
code on the inside the back cover of this manual. Default = One.
Number of Pulses
Good Read Delay
This sets the minimum amount of time before the scanner can read another bar
code. Default = No Delay.
* No Delay
Short Delay (500 ms)
Medium Delay (1000 ms)
Long Delay (1500 ms)
User-Specified Good Read Delay
If you want to set your own length for the good read delay, scan the bar code
below, then set the delay (from 0-30,000 milliseconds) by scanning digits from
the inside back cover, then scanning Save.
User-Specified Good Read Delay
3 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Trigger Modes
Manual/Serial Trigger
You can activate the scanner either by pressing the trigger, or using a serial trig-
mode, the scanner scans until a bar code is read, or until the trigger is released.
When in serial mode, the scanner scans until a bar code has been read or until
the deactivate command is sent. In serial mode, the scanner can also be set to
lows).
* Manual/Serial Trigger
Read Time-Out
Use this selection to set a time-out (in milliseconds) of the scanner’s trigger
when using serial commands to trigger the scanner. Once the scanner has
timed out, you can activate the scanner either by pressing the trigger or using a
serial trigger command. After scanning the Read Time-Out bar code, set the
time-out duration (from 0-300,000 milliseconds) by scanning digits from the
inside back cover, then scanning Save. Default = 30,000.
Read Time-Out
Automatic Trigger
The scanner scans continuously using internal LEDs to detect bar codes.
Automatic Trigger
3 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Presentation Mode
Presentation Mode uses ambient light to detect bar codes. The LEDs are off for
ambient conditions until a change occurs in the scanner’s field of view. Then
the LEDS turn on automatically to read the code. If the light level in the room is
not high enough, Presentation Mode may not work properly.
Presentation Mode
Continuous Illumination Mode (Manual Trigger only)
If you have several bar codes that are close together, you may wish to have a
continuous aiming beam on in order to properly aim the scanner at one bar
code. Scan the Continuous Illumination On bar code to program the scanner
for this capability. Once you have the aiming beam over the correct bar code,
pull the trigger to read the code. Scan the Continuous Illumination Off bar
code to turn off this feature.
Continuous Illumination
Mode On
* Continuous Illumination
Mode Off
Hands Free Time-Out
The Automatic Trigger and Presentation Modes are referred to as “hands free”
modes. If the scanner’s trigger is pulled when using a hands free mode, the
scanner changes to manual trigger mode. You can set the time the scanner
should remain in manual trigger mode by setting the Hands Free Time-Out.
Once the time-out value is reached, (if there have been no further trigger pulls)
the scanner reverts to the original hands free mode.
3 - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan the Hands Free Time-Out bar code, then scan the time-out duration
(from 0-300,000 milliseconds) from the inside back cover, and Save. Default =
5,000 ms.
Hands Free Time-Out
Reread Delay
This sets the time period before the scanner can read the same bar code a sec-
ond time. Setting a reread delay protects against accidental rereads of the
same bar code. Longer delays are effective in minimizing accidental rereads at
POS (point of sale). Use shorter delays in applications where repetitive bar
code scanning is required. Default = Medium.
Reread Delay only works when in automatic trigger mode or presentation mode
Short (500 ms)
* Medium (750 ms)
Long (1000 ms)
Extra Long (2000 ms)
3 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the bar code below,
then set the delay (from 0-30,000 milliseconds) by scanning digits from the
inside back cover, then scanning Save.
User-Specified Reread Delay
Centering
Use Centering to narrow the scanner’s field of view to make sure the scanner
reads only those bar codes intended by the user. For instance, if multiple codes
are placed closely together, centering will insure that only the desired codes are
read.
If a bar code is not touched by a predefined window, it will not be decoded or
output by the scanner. If centering is turned on by scanning Centering On, the
scanner only reads codes that pass through the centering window you specify
using the Left of Centering Window, or Right of Centering Window bar
codes.
In the example below, the red line is the full scanner field of view and the white
boxed area is the centering window. The centering window has been set to
20% left and 30% right, as shown in the legend at the bottom. Since Bar Code
1 passes through the centering window, it will be read. Bar Code 2 does not
pass through the centering window, so it will not be read.
Bar Code 1
Bar Code 2
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
Scan Centering On, then scan one of the following bar codes to change the left
or right of the centering window. Then scan the percent you want to shift the
centering window using digits on the inside back cover of this manual. Scan
Save. Default Centering = 40% for Left, 60% for Right.
3 - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Output Sequence Overview
Output Sequence Editor
This programming selection allows you to program the scanner to output data
(when scanning more than one symbol) in whatever order your application
requires, regardless of the order in which the bar codes are scanned. Reading
the Default Sequence symbol programs the scanner to the Universal values,
shown below. These are the defaults. Be certain you want to delete or clear all
formats before you read the Default Sequence symbol.
Note: To make Output Sequence Editor selections, you’ll need to know the
code I.D., code length, and character match(es) your application
requires. Use the Alphanumeric symbols (inside back cover) to read
these options.
Note: You must hold the trigger while reading each bar code in a sequence.
To Add an Output Sequence
2. Code I.D.
want to apply the output sequence format. Locate the Hex value for that
symbology and scan the 2 digit hex value from the Programming Chart
(inside back cover).
3. Length
Specify what length (up to 9999 characters) of data output will be acceptable
for this symbology. Scan the four digit data length from the Programming
Chart. (Note: 50 characters is entered as 0050. 9999 is a universal num-
ber, indicating all lengths.) When calculating the length, you must count any
programmed prefixes, suffixes, or formatted characters as part of the length
(unless using 9999).
4. Character Match Sequences
value that represents the character(s) you want to match. Use the Program-
ming Chart to read the alphanumeric combination that represents the ASCII
characters. (99 is the Universal number, indicating all characters.)
5. End Output Sequence Editor
Scan F F to enter an Output Sequence for an additional symbology, or Save
to save your entries.
Other Programming Selections
•Discard
This exits without saving any Output Sequence changes.
3 - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Output Sequence Editor
Enter Sequence
Default Sequence
Output Sequence Example
In this example, you are scanning Code 93, Code 128, and Code 39 barcodes,
but you want the image scanner to output Code 39 1st, Code 128 2nd, and
Code 93 3rd, as shown below.
Note: Code 93 must be enabled to use this example.
A - Code 39
B - Code 128
C - Code 93
You would set up the sequence editor with the following command line:
SEQBLK62999941FF6A999942FF69999943FF
The breakdown of the command line is shown below:
SEQBLKsequence editor start command
62 code identifier for Code 39
9999 code length that must match for Code 39, 9999 = all lengths
41 start character match for Code 39, 41h = “A”
FF termination string for first code
6A code identifier for Code 128
9999 code length that must match for Code 128, 9999 = all lengths
3 - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
42 start character match for Code 128, 42h = “B”
FF termination string for second code
69 code identifier for Code 93
9999 code length that must match for Code 93, 9999 = all lengths
43 start character match for Code 93, 43h = “C”
FF termination string for third code
To program the previous example using specific lengths, you would have to
count any programmed prefixes, suffixes, or formatted characters as part of the
specific code lengths, you would use the following command line:
SEQBLK62001241FF6A001342FF69001243FF
The breakdown of the command line is shown below:
SEQBLK sequence editor start command
62
code identifier for Code 39
0012
41
FF
A - Code 39 sample length (11) plus CR suffix (1) = 12
start character match for Code 39, 41h = “A”
termination string for first code
6A
code identifier for Code 128
0013
42
FF
B - Code 128 sample length (12) plus CR suffix (1) = 13
start character match for Code 128, 42h = “B”
termination string for second code
69
code identifier for Code 93
0012
43
FF
C - Code 93 sample length (11) plus CR suffix (1) = 12
start character match for Code 93, 43h = “C”
termination string for third code
3 - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Output Sequence Editor
Enter Sequence
Default Sequence
Require Output Sequence
When an output sequence is Required, all output data must conform to an
edited sequence or the image scanner will not transmit the output data to the
host device. When it’s On/Not Required, the image scanner will attempt to get
the output data to conform to an edited sequence, but if it cannot, the image
scanner transmits all output data to the host device as is.
When the output sequence is Off, the barcode data is output to the host as the
image scanner decodes it.
Note: This selection is unavailable when the Multiple Symbols Selection is
turned on.
Required
On/Not Required
*Off
Multiple Symbols
When this programming selection is turned On, it allows you to read multiple
symbols with a single pull of the scanner’s trigger. If you press and hold the trig-
ger, aiming the scanner at a series of symbols, it reads unique symbols once,
3 - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
beeping (if turned on) for each read. The scanner attempts to find and decode
new symbols as long as the trigger is pulled. When this programming selection
is turned Off, the scanner will only read the symbol closest to the aiming beam.
On
* Off
No Read
With No Read turned On, the scanner sends an “NR” to the host if you pull and
release the trigger without reading a code (e.g., bad bar code). If No Read is
turned Off, the “NR” will not be sent to the host.
On
* Off
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,”
hex code for the No Read symbol is 9C.
3 - 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Reverse
Video Reverse is used to allow the scanner to read bar codes that are inverted.
The “Off” bar code below is an example of this type of bar code.
Note: If additional menuing is required, Video Reverse must be disabled to read
the menu bar codes and then re-enabled after menuing is completed.
On
VIDREV0REV.
* Off
3 - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
3 - 16
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Data Editing
Prefix/Suffix Overview
When a bar code is scanned, additional information is sent to the host computer
along with the bar code data. This group of bar code data and additional,
user-defined data is called a “message string.” The selections in this section
are used to build the user-defined data into the message string.
Prefix and Suffix characters are data characters that can be sent before and
after scanned data. You can specify if they should be sent with all symbologies,
or only with specific symbologies. The following illustration shows the break-
down of a message string:
Prefix
1-11
alpha numeric
characters
Scanned Data
Suffix
1-11
alpha numeric
characters
variable length
Points to Keep In Mind
•
It is not necessary to build a message string. The selections in this chapter
are only used if you wish to alter the default settings.
suffix.
•
•
A prefix or suffix may be added or cleared from one symbology or all
symbologies.
You can add any prefix or suffix from the ASCII Conversion Chart (Code Page
•
•
You can string together several entries for several symbologies at one time.
Enter prefixes and suffixes in the order in which you want them to appear on
the output.
•
•
When setting up for specific symbologies (as opposed to all symbologies), the
specific symbology ID value counts as an added prefix or suffix character.
The maximum size of a prefix or suffix configuration is 200 characters, which
includes header information
4 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
To Add a Prefix or Suffix
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in
Appendix A) for the symbology to which you want to apply the prefix or
suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”.
scan 9, 9 for all symbologies.
ual.
Step 6. Repeat Steps 4 and 5 for every prefix or suffix character.
Step 7. To add the Code I.D., scan 5, C, 8, 0.
To add AIM I.D., scan 5, C, 8, 1.
To add a backslash (\), scan 5, C, 5, C.
Note: To add a backslash (\) as in Step 7, you must scan 5C twice – once to
create the leading backslash and then to create the backslash itself.
Step 8. Scan Save to exit and save, or scan Discard to exit without saving.
Repeat Steps 1-6 to add a prefix or suffix for another symbology.
Example: Add a Tab Suffix to All Symbologies
Step 1. Scan Add Suffix.
manual to apply this suffix to all symbologies.
manual. This corresponds with the hex value for a horizontal tab,
Step 4. Scan Save, or scan Discard to exit without saving.
To Clear One or All Prefixes or Suffixes
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbol-
ogy. When you Clear One Prefix (Suffix), the specific character you select is
deleted from the symbology you want. When you Clear All Prefixes (Suffixes),
all the prefixes or suffixes for a symbology are deleted.
4 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in
Appendix A) for the symbology from which you want to clear the prefix
or suffix.
ual or scan 9, 9 for all symbologies.
Your change is automatically saved.
To Add a Carriage Return Suffix to All Symbologies
Scan the following bar code if you wish to add a carriage return suffix to all sym-
bologies at once. This action first clears all current suffixes, then programs a
carriage return suffix for all symbologies.
Add CR Suffix
All Symbologies
Prefix Selections
Add Prefix
Clear One Prefix
Clear All Prefixes
4 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Suffix Selections
Add Suffix
Clear One Suffix
Clear All Suffixes
Transmit Alternate Extended ASCII Characters
You may need to emulate special keyboard functions, such as up or down
arrows, Alt/Make or Alt/Break commands, that are not supported in the
mal and hex characters. If you scan the Transmit Alternate Extended ASCII
code, any hex entries in a prefix or suffix will result in the corresponding Key-
board Function output.
Example: Transmit Alternate Extended ASCII is enabled, and you scan Add
Suffix, then scan 9 9 8 9. All symbologies (99) would have a suffix
of a Page Down (hex 89) added to them.
When Transmit Normal Extended ASCII is selected, the normal extended
Example: Transmit Normal Extended ASCII is enabled, and you scan Add
Suffix, then scan 9 9 8 9. All symbologies (99) would have a suffix
of a ‰ character added to them.
Default = Transmit Alternate Extended ASCII.
Transmit Alternate Extended
ASCII
* Transmit Normal Extended
ASCII
4 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Extended ASCII Characters
DEC HEX Keyboard Function
DEC HEX Keyboard Function
128 80
129 81
130 82
131 83
152 98 F9
153 99 F10
154 9A F11
155 9B F12
up arrow ↑
down arrow ↓
right arrow →
left arrow ←
Insert
Delete
Home
End
Page Up
Page Down
Right ALT
Right CTRL
Reserved
Reserved
Numeric Keypad Enter
Numeric Keypad /
F1
F2
F3
F4
F5
F6
F7
F8
132 84
133 85
134 86
135 87
136 88
137 89
138 8A
139 8B
140 8C
141 8D
142 8E
143 8F
144 90
145 91
146 92
147 93
148 94
149 95
150 96
151 97
156 9C Numeric Keypad +
157 9D Numeric Keypad -
158 9E Numeric Keypad *
159 9F Caps Lock
160 A0 Num Lock
161 A1 Left Alt
162 A2 Left Ctrl
163 A3 Left Shift
164 A4 Right Shift
165 A5 Print Screen
166 A6 Tab
167 A7 Shift Tab
168 A8 Enter
169 A9 Esc
170 AA Alt Make
171 AB Alt Break
172 AC Control Make
173 AD Control Break
174 AE Alt Sequence with 1 Character
175 AF Ctrl Sequence with 1 Character
4 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Code Transmit
When this selection is enabled and function codes are contained within the
scanned data, the scanner transmits the function code to the terminal. Charts
verted to a key code before it is transmitted. Default = Enable.
* Enable
Disable
Intercharacter, Interfunction, and Intermessage
Delays
Some terminals drop information (characters) if data comes through too quickly.
Intercharacter, interfunction, and intermessage delays slow the transmission of
data, increasing data integrity.
Each delay is composed of a 5 millisecond step. You can program up to 99
steps (of 5 ms each) for a range of 0-495 ms.
4 - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Intercharacter Delay
An intercharacter delay of up to 495 milliseconds may be placed between the
transmission of each character of scanned data. Scan the Intercharacter
Delay bar code below, then scan the number of steps in 5 millisecond incre-
ments and the Save bar code using the inside the back cover of this manual.
Prefix
Scanned Data
Suffix
1
2
3
4
5
Intercharacter Delay
Intercharacter Delay
To remove this delay, scan the Intercharacter Delay bar code, then set the
number of steps to 0. Scan the Save bar code using the inside the back cover
of this manual.
Note: Intercharacter delays are not supported in USB serial.
User Specified Intercharacter Delay
An intercharacter delay of up to 495 milliseconds may be placed after the trans-
mission of a particular character of scanned data. Scan the Delay Length bar
code below, then scan the number of steps in 5 millisecond increments and the
Next, scan the Character to Trigger Delay bar code, then the 2-digit hex value
Delay Length
Character to Trigger Delay
4 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
To remove this delay, scan the Delay Length bar code, and set the number of
manual.
Interfunction Delay
An interfunction delay of up to 495 milliseconds may be placed between the
transmission of each control character in the message string. Scan the Inter-
function Delay bar code below, then scan the number of steps in 5 millisecond
ual.
Prefix
STX
Scanned Data
3 4
Suffix
CR
1
HT
2
5
LF
Interfunction Delays
Interfunction Delay
To remove this delay, scan the Interfunction Delay bar code, then set the num-
this manual.
Intermessage Delay
An intermessage delay of up to 495 milliseconds may be placed between each
scan transmission. Scan the Intermessage Delay bar code below, then scan
the number of steps in 5 millisecond increments and the Save bar code using
the inside the back cover of this manual.
1st Scan Transmission 2nd Scan Transmission
Intermessage Delay
Intermessage Delay
4 - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
To remove this delay, scan the Intermessage Delay bar code, then set the
of this manual.
4 - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
4 - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Data Formatting
Data Format Editor Introduction
You may use the Data Format Editor to change the scanner’s output. For exam-
ple, you can use the Data Format Editor to insert characters at certain points in
bar code data as it is scanned. The selections in the following pages are used
only if you wish to alter the output. Default Data Format setting = None.
Normally, when you scan a bar code, it gets outputted automatically; however
on page 5-4) within the format program to output data.
Multiple formats may be programmed into the scanner. They are stacked in the
order in which they are entered. However, the following list presents the order
in which formats are applied:
1. Specific Term ID, Actual Code ID, Actual Length
2. Specific Term ID, Actual Code ID, Universal Length
3. Specific Term ID, Universal Code ID, Actual Length
4. Specific Term ID, Universal Code ID, Universal Length
5. Universal Term ID, Actual Code ID, Actual Length
6. Universal Term ID, Actual Code ID, Universal Length
7. Universal Term ID, Universal Code ID, Actual Length
8. Universal Term ID, Universal Code ID, Universal Length
The maximum size of a data format configuration is 256 bytes, which includes
header information. No format can contain more than 50 bytes.
If a bar code is read that fails the first data format, the next data format, if there
is one, will be used on the bar code data. If there is no other data format, the
raw data is output.
If you have changed data format settings, and wish to clear all formats and
return to the factory defaults, scan the Default Data Format code below.
* Default Data Format
To Add a Data Format
Step 2. Select Primary Format
Scan 0 using the inside the back cover of this manual to indicate that
this is your primary format.
5 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3. Terminal Type
minal ID number for your PC. Scan three numeric bar codes on the
inside back cover to program the scanner for your terminal ID (you must
enter 3 digits). For example, scan 0 0 3 for an AT wedge.
Note: The wildcard for all terminal types is 099.
Step 4. Code I.D.
format. Locate the Hex value for that symbology and scan the 2 digit
Step 5. Length
Specify what length (up to 9999 characters) of data will be acceptable
back cover of this manual. (Note: 50 characters is entered as 0050.
9999 is a universal number, indicating all lengths.)
Step 6. Editor Commands
symbols that represent the command you want to enter.
entries.
Enter Data Format
Save
Discard
Other Programming Selections
•
Clear One Data Format
back cover of this manual to indicate you are clearing your primary format.
Scan the Terminal Type (refer to the Supported Terminals Chart on page 5-
5 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
data length for the specific data format that you want to delete. All other
formats remain unaffected.
•
•
This exits, saving any Data Format changes.
This exits without saving any Data Format changes.
Clear One Data Format
Clear All Data Formats
Save
Discard
5 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Interface / Terminal ID Table
Interface
Terminal ID
USB
PC keyboard (HID)
Mac Keyboard
PC Keyboard (Japanese)
Serial (COM driver required)
HID POS
USB SurePOS Handheld
USB SurePOS Tabletop
RS232 TTL
124
125
134
130
131
128
129
000
000
051
003
002
Serial
RS232 True
RS485 (IBM-HHBCR 1+2, 46xx)
PS2 compatibles
Keyboard
AT compatibles
Data Format Editor Commands
When working with the Data Format Editor, a virtual cursor is moved along your
input data string. The following commands are used to both move this cursor to
different positions, and to select, replace, and insert data into the final output.
Send Commands
Send all characters
F1 Include in the output message all of the characters from the input
message, starting from current cursor position, followed by an insert
character. Syntax = F1xx where xx stands for the insert character’s hex
Send a number of characters
F2 Include in the output message a number of characters followed by an
insert character. Start from the current cursor position and continue for
“nn” characters or through the last character in the input message,
followed by character “xx.” Syntax = F2nnxx where nn stands for the
numeric value (00-99) for the number of characters, and xx stands for
the the insert character’s hex value for the CP1252 character. Refer to
hex and character codes.
5 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
F2 Example: Send a number of characters
Send the first 10 characters from the bar code above, followed by a
carriage return. Command string: F2100D
F2 is the “Send a number of characters” command
10 is the number of characters to send
0D is the hex value for a CR
The data is output as: 1234567890
F2 and F1 Example: Split characters into 2 lines
Send the first 10 characters from the bar code above, followed by a
carriage return, followed by the rest of the characters.
Command string: F2100DF10D
F2 is the “Send a number of characters” command
10 is the number of characters to send for the first line
0D is the hex value for a CR
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 1234567890
ABCDEFGHIJ
<CR>
Send all characters up to a particular character
F3 Include in the output message all characters from the input message,
starting with the character at the current cursor position and continuing
to, but not including, the search character “ss,” followed by an insert
character. The cursor is moved forward to the “ss” character. Syntax
= F3ssxx where ss stands for the search character’s hex value for the
CP1252 character, and xx stands for the insert character’s hex value for
the CP1252 character.
decimal, hex and character codes.
F3 Example: Send all characters up to a particular character
Using the bar code above, send all characters up to but not including
“D,” followed by a carriage return.
Command string: F3440D
F3 is the “Send all characters up to a particular character” command
5 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
44 is the hex value for a 'D”
0D is the hex value for a CR
The data is output as: 1234567890ABC
<CR>
Send all but the last characters
E9 Include in the output message all but the last “nn” characters, starting
from the current cursor position. The cursor is moved forward to one
position past the last input message character included. Syntax = E9nn
where nn stands for the numeric value (00-99) for the number of
characters that will not be sent at the end of the message.
Insert a character multiple times
F4 Send “xx” character “nn” times in the output message, leaving the
cursor in the current position. Syntax = F4xxnn where xx stands for the
insert character’s hex value for the CP1252 character, and nn is the
numeric value (00-99) for the number of times it should be sent. Refer
decimal, hex and character codes.
E9 and F4 Example: Send all but the last characters, followed by
2 tabs
Send all characters except for the last 8 from the bar code above, fol-
lowed by 2 tabs.
Command string: E908F40902
E9 is the “Send all but the last characters” command
08 is the number of characters at the end to ignore
F4 is the “Insert a character multiple times” command
09 is the hex value for a horizontal tab
02 is the number of time the tab character is sent
The data is output as: 1234567890AB <tab><tab>
Insert symbology name
B3 Insert the name of the bar code’s symbology in the output message,
without moving the cursor. Only symbologies with a Honeywell ID are
character codes.
5 - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert bar code length
B4 Insert the bar code’s length in the output message, without moving the
cursor. The length is expressed as a numeric string and does not
include leading zeroes.
B3 and B4 Example: Insert the symbology name and length
Send the symbology name and length before the bar code data from
the bar code above. Break up these insertions with spaces. End with
a carriage return.
Command string: B3F42001B4F42001F10D
B3 is the “Insert symbology name” command
F4 is the “Insert a character multiple times” command
20 is the hex value for a space
01 is the number of time the space character is sent
B4 is the “Insert bar code length” command
F4 is the “Insert a character multiple times” command
20 is the hex value for a space
01 is the number of time the space character is sent
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: Code128 20 1234567890ABCDEFGHIJ
<CR>
Move Commands
Move the cursor forward a number of characters
F5 Move the cursor ahead “nn” characters from current cursor position.
Syntax = F5nn where nn is the numeric value (00-99) for the number
of characters the cursor should be moved ahead.
F5 Example: Move the cursor forward and send the data
Move the cursor forward 3 characters, then send the rest of the the bar
code data from the bar code above. End with a carriage return.
Command string: F503F10D
F5 is the “Move the cursor forward a number of characters” command
5 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
03 is the number of characters to move the cursor
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 4567890ABCDEFGHIJ
<CR>
Move the cursor backward a number of characters
F6 Move the cursor back “nn” characters from current cursor position.
Syntax = F6nn where nn is the numeric value (00-99) for the number
of characters the cursor should be moved back.
Move the cursor to the beginning
F7 Move the cursor to the first character in the input message. Syntax =
F7.
Move the cursor to the end
EA Move the cursor to the last character in the input message. Syntax =
EA.
Search Commands
Search forward for a character
F8 Search the input message forward for “xx” character from the current
cursor position, leaving the cursor pointing to the “xx” character.
Syntax = F8xx where xx stands for the search character’s hex value for
the CP1252 character.
decimal, hex and character codes.
F8 Example: Send bar code data that starts after a particular
character
Search for the letter “D” in bar codes and send all the data that follows,
including the “D.” Using the bar code above:
Command string: F844F10D
F8 is the “Search forward for a character” command
44 is the hex value for “D”
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: DEFGHIJ
<CR>
5 - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Search backward for a character
F9 Search the input message backward for “xx” character from the current
cursor position, leaving the cursor pointing to the “xx” character. Syntax
= F9xx where xx stands for the search character’s hex value for the
CP1252 character.
decimal, hex and character codes.
Search forward for a string
B0 Search forward for “s” string from the current cursor position, leaving
cursor pointing to “s” string. Syntax = B0nnnnS where nnnn is the string
length (up to 9999), and S consists of the ASCII hex value of each
character in the match string. For example, B0000454657374 will
search forward for the first occurrence of the 4 character string “Test.”
decimal, hex and character codes.
B0 Example: Send bar code data that starts after a string of char-
acters
Search for the letters “FGH” in bar codes and send all the data that fol-
lows, including “FGH.” Using the bar code above:
Command string: B00003464748F10D
B0 is the “Search forward for a string” command
0003 is the string length (3 characters)
46 is the hex value for “F”
47 is the hex value for “G”
48 is the hex value for “H”
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: FGHIJ
<CR>
Search backward for a string
B1 Search backward for “s” string from the current cursor position, leaving
cursor pointing to “s” string. Syntax = B1nnnnS where nnnn is the string
length (up to 9999), and S consists of the ASCII hex value of each
character in the match string. For example, B1000454657374 will
search backward for the first occurrence of the 4 character string “Test.”
decimal, hex and character codes.
5 - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Search forward for a non-matching character
E6 Search the input message forward for the first non-“xx” character from
the current cursor position, leaving the cursor pointing to the non-“xx”
character. Syntax = E6xx where xx stands for the search character’s
codes.
E6 Example: Remove zeroes at the beginning of bar code data
This example shows a bar code that has been zero filled. You may
want to ignore the zeroes and send all the data that follows. E6
searches forward for the first character that is not zero, then sends all
the data after, followed by a carriage return. Using the bar code
above:
Command string: E630F10D
E6 is the “Search forward for a non-matching character” command
30 is the hex value for 0
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 37692
<CR>
Search backward for a non-matching character
E7 Search the input message backward for the first non-“xx” character
from the current cursor position, leaving the cursor pointing to the non-
“xx” character. Syntax = E7xx where xx stands for the search
character codes.
Miscellaneous Commands
Suppress characters
FB Suppress all occurrences of up to 15 different characters, starting at the
current cursor position, as the cursor is advanced by other commands.
When the FC command is encountered, the suppress function is
terminated. The cursor is not moved by the FB command.
Syntax = FBnnxxyy . .zz where nn is a count of the number of
suppressed characters in the list, and xxyy .. zz is the list of characters
to be suppressed.
5 - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
FB Example: Remove spaces in bar code data
This example shows a bar code that has spaces in the data. You may
want to remove the spaces before sending the data. Using the bar
code above:
Command string: FB0120F10D
FB is the “Suppress characters” command
01 is the number of character types to be suppressed
20 is the hex value for a space
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 34567890
<CR>
Stop suppressing characters
FC Disables suppress filter and clear all suppressed characters. Syntax =
FC.
Replace characters
E4 Replaces up to 15 characters in the output message, without moving
the cursor. Replacement continues until the E5 command is
encountered. Syntax = E4nnxx xx yy yy ...zz zz where nn is the total
1
2
1
2
1
2
count of of the number of characters in the list (characters to be
replaced plus replacement characters); xx defines characters to be
1
replaced and xx defines replacement characters, continuing through
2
zz and zz .
1
2
E4 Example: Replace zeroes with CRs in bar code data
If the bar code has characters that the host application does not want
included, you can use the E4 command to replace those characters
with something else. In this example, you will replace the zeroes in the
bar code above with carriage returns.
Command string: E402300DF10D
E4 is the “Replace characters” command
02 is the total count of characters to be replaced, plus the replacement
characters (0 is replaced by CR, so total characters = 2)
30 is the hex value for 0
0D is the hex value for a CR (the character that will replace the 0)
5 - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 1234
5678
ABC
<CR>
Stop replacing characters
E5 Terminates character replacement. Syntax = E5.
Compare characters
FE Compare the character in the current cursor position to the character
“xx.” If characters are equal, move the cursor forward one position.
Syntax = FExx where xx stands for the comparison character’s hex
value for the CP1252 character.
decimal, hex and character codes.
Compare string
B2 Compare the string in the input message to the string “s.” If the strings
are equal, move the cursor forward past the end of the string. Syntax
= B2nnnnS where nnnn is the string length (up to 9999), and S consists
of the ASCII hex value of each character in the match string. For
example, B2000454657374 will compare the string at the current
cursor position with the 4 character string “Test.”
decimal, hex and character codes.
Check for a number
EC Check to make sure there is an ASCII number at the current cursor
position. The format is aborted if the character is not numeric.
EC Example: Only output the data if the bar code begins with a
number
If you want only data from bar codes that begin with a number, you can
use EC to check for the number.
Command string: ECF10D
EC is the “Check for a number” command
F1 is the “Send all characters” command
0D is the hex value for a CR
If this bar code is read,
the next data format,
if there is one, will be used on the data. If there is no other format, the
format fails and the raw data is output as AB1234.
5 - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
If this bar code is read:
the data is output as:
1234AB
<CR>
Check for non-numeric character
ED Check to make sure there is a non-numeric ASCII character at the
current cursor position. The format is aborted if the character is
numeric.
ED Example: Only output the data if the bar code begins with a
letter
If you want only data from bar codes that begin with a letter, you can
use ED to check for the letter.
Command string: EDF10D
ED is the “Check for a non-numeric character” command
F1 is the “Send all characters” command
0D is the hex value for a CR
If this bar code is read,
the next data format, if
there is one, will be used on this data. If there is no other format, the
format fails and the raw data is output as 1234AB.
If this bar code is read:
the data is output as:
AB1234
<CR>
Insert a delay
EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting
from the current cursor position. Syntax = EFnnnn where nnnn stands
for the delay in 5ms increments, up to 9999. This command can only
be used with keyboard emulation.
5 - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Format Editor
Enter Data Format
* Default Data Format
Clear One Data Format
Clear All Data Formats
Save
Discard
Data Formatter
When Data Formatter is turned off, the bar code data is output to the host as
read (including prefixes and suffixes). Choose one of the following options.
5 - 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Default = Data Formatter On.
* Data Formatter On,
but Not Required
Data Formatter Off
When Data Formatter is required, all input data must conform to an edited for-
mat or the scanner does not transmit the input data to the host device.
Data Format On, Format Required
5 - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
5 - 16
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Symbologies
Introduction
This programming section contains the following menu selections. Refer to
Chapter 9 for settings and defaults.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
6 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
All Symbologies
If you want to decode all the symbologies allowable for your scanner, scan the
All Symbologies On code. If on the other hand, you want to decode only a
particular symbology, scan All Symbologies Off followed by the On symbol for
that particular symbology.
All Symbologies On
All Symbologies Off
Message Length
You are able to set the valid reading length of some of the bar code symbologies.
If the data length of the scanned bar code doesn’t match the valid reading length,
the scanner will issue an error beep. You may wish to set the same value for
minimum and maximum length to force the scanner to read fixed length bar code
data. This helps reduce the chances of a misread.
6 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
EXAMPLE:Decode only those bar codes with a count of 9-20 characters.
Min. length = 09 Max. length = 20
EXAMPLE:Decode only those bar codes with a count of 15 characters.
Min. length = 15 Max. length = 15
For a value other than the minimum and maximum message length defaults,
scan the bar codes included in the explanation of the symbology, then scan the
cover of this manual. The minimum and maximum lengths and the defaults are
included with the respective symbologies.
Codabar
<Default All Codabar Settings>
Codabar
*On
Off
Codabar Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You
may either transmit, or not transmit Start/Stop characters.
6 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Default = Don’t Transmit.
Transmit
* Don’t Transmit
Codabar Check Character
Codabar check characters are created using different “modulos.” You can pro-
gram the scanner to read only Codabar bar codes with Modulo 16 check char-
acters. Default = No Check Character.
No Check Character indicates that the scanner reads and transmits bar code
data with or without a check character.
When Check Character is set to Validate and Transmit, the scanner will only
read Codabar bar codes printed with a check character, and will transmit this
character at the end of the scanned data.
When Check Character is set to Validate, but Don’t Transmit, the unit will only
read Codabar bar codes printed with a check character, but will not transmit the
check character with the scanned data.
* No Check Character
Validate Modulo 16, but
Don’t Transmit
Validate Modulo 16 and Transmit
6 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Codabar Concatenation
Codabar supports symbol concatenation. When you enable concatenation, the
scanner looks for a Codabar symbol having a “D” start character, adjacent to a
symbol having a “D” stop character. In this case the two messages are concat-
enated into one with the “D” characters omitted.
Character
Start
Stop
Start
Stop
Codabar
A12D
D34A
Select Require to prevent the scanner from decoding a single “D” Codabar sym-
bol without its companion. This selection has no effect on Codabar symbols
without Stop/Start D characters.
On
* Off
Require
6 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Code 39
< Default All Code 39 Settings >
Code 39
*On
Off
Code 39 Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You
may either transmit, or not transmit Start/Stop characters. Default = Don’t
Transmit.
Transmit
* Don’t Transmit
Code 39 Check Character
No Check Character indicates that the scanner reads and transmits bar code
data with or without a check character.
When Check Character is set to Validate, but Don’t Transmit, the unit only
reads Code 39 bar codes printed with a check character, but will not transmit
the check character with the scanned data.
6 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
When Check Character is set to Validate and Transmit, the scanner only reads
Code 39 bar codes printed with a check character, and will transmit this charac-
ter at the end of the scanned data. Default = No Check Character.
* No Check Character
Validate, but Don’t Transmit
Validate and Transmit
Code 39 Message Length
lengths = 0-48. Minimum Default = 0, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Code 39 Append
This function allows the scanner to append the data from several Code 39 bar
codes together before transmitting them to the host computer. When this func-
tion is enabled, the scanner stores those Code 39 bar codes that start with a
space (excluding the start and stop symbols), and does not immediately trans-
mit the data. The scanner stores the data in the order in which the bar codes
6 - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
are read, deleting the first space from each. The scanner transmits the
appended data when it reads a Code 39 bar code that starts with a character
other than a space. Default = Off.
On
*Off
Code 32 Pharmaceutical (PARAF)
Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian
pharmacies. This symbology is also known as PARAF. Default = Off.
On
* Off
6 - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Full ASCII
If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar
code symbol will be interpreted as a single character. For example: $V will be
decoded as the ASCII character SYN, and /C will be decoded as the ASCII
character #. Default = Off.
NUL %U
SOH $A
STX $B
ETX $C
EOT $D
ENQ $E
ACK $F
BEL $G
BS $H
HT $I
DLE $P
DC1 $Q
DC2 $R
DC3 $S
DC4 $T
NAK $U
SYN $V
ETB $W
CAN $X
EM $Y
SUB $Z
ESC %A
FS %B
GS %C
RS %D
US %E
SP
!
SPACE
/A
/B
/C
/D
/E
/F
/G
/H
/I
0
1
2
3
4
5
6
7
8
9
:
0
@
A
B
C
D
E
F
%V
A
B
C
D
E
F
P
Q
R
S
T
U
V
W
X
Y
Z
[
P
‘
%W
+A
+B
+C
+D
+E
+F
+G
+H
+I
p
q
r
+P
+Q
+R
+S
+T
1
Q
a
b
c
d
e
f
“
2
R
#
$
%
&
‘
3
S
s
t
4
T
5
U
u
v
w
x
y
z
{
+U
+V
+W
+X
+Y
+Z
6
V
7
G
H
I
G
H
I
W
X
g
h
i
(
8
)
9
Y
LF $J
VT $K
FF $L
CR $M
SO $N
*
/J
/Z
%F
%G
%H
%I
%J
J
J
Z
j
+J
+
,
/K
/L
;
K
L
K
L
%K
%L
%M
%N
%O
k
l
+K
+L
%P
%Q
%R
%S
<
=
>
?
\
|
-
-
M
N
O
M
N
O
]
m
n
o
+M
+N
}
.
.
^
~
SI
$O
/
/O
_
+O DEL %T
Character pairs /M and /N decode as a minus sign and period respectively.
Character pairs /P through /Y decode as 0 through 9.
Full ASCII On
* Full ASCII Off
Code 39 Code Page
Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the bar
code being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the bar code below,
select the code page with which the bar codes were created from the chart,
6 - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
characters should then appear properly.
Code 39 Code Page
Interleaved 2 of 5
< Default All Interleaved 2 of 5 Settings >
Interleaved 2 of 5
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits bar code data
with or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads
Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the
check digit with the scanned data.
6 - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
When Check Digit is set to Validate and Transmit, the scanner only reads
Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit
at the end of the scanned data. Default = No Check Digit.
* No Check Digit
Validate, but Don’t Transmit
Validate and Transmit
Interleaved 2 of 5 Message Length
lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
6 - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Code 93
< Default All Code 93 Settings >
Code 93
* On
Off
Code 93 Message Length
lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Code 93 Code Page
Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the bar
code being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the bar code below,
6 - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
select the code page with which the bar codes were created from the chart,
characters should then appear properly.
Code 93 Code Page
6 - 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Straight 2 of 5 Industrial (three-bar start/stop)
<Default All Straight 2 of 5 Settings>
Straight 2 of 5 Industrial
* On
Off
Straight 2 of 5 Industrial Message Length
lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
6 - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Straight 2 of 5 IATA (two-bar start/stop)
<Default All Code IATA 2 of 5 Settings>
Straight 2 of 5 IATA
On
Off
Straight 2 of 5 IATA Message Length
lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
6 - 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Code 11 Message Length
lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Code 128
<Default All Code 128 Settings>
Code 128
* On
Off
ISBT 128 Concatenation
In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard
for communicating critical blood information in a uniform manner. The use of
ISBT formats requires a paid license. The ISBT 128 Application Specification
describes 1) the critical data elements for labeling blood products, 2) the current
recommendation to use Code 128 due to its high degree of security and its
6 - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
space-efficient design, 3) a variation of Code 128 that supports concatenation
of neighboring symbols, and 4) the standard layout for bar codes on a blood
product label. Use the bar codes below to turn concatenation on or off. Default
=Off.
On
* Off
Code 128 Message Length
lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Code 128 Code Page
Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the bar
code being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the bar code below,
select the code page with which the bar codes were created from the chart,
characters should then appear properly.
6 - 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Code 128 Code Page
Code 128 Function Code Transmit
By default, Code 128 function codes are not transmitted with Code 128 bar
code data. However, if you wish to transmit Code 128 function codes with the
bar code data, scan the Function Codes On bar code, below. Default = Off
* Function Codes Off
Function Codes On
Telepen
<Default All Telepen Settings>
6 - 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Telepen
On
* Off
Telepen Output
Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1
and decodes them as standard full ASCII (start/stop pattern 1). When Original
Telepen Output is selected, the scanner reads symbols with start/stop pattern 1
and decodes them as compressed numeric with optional full ASCII (start/stop
pattern 2). Default = AIM Telepen Output.
*AIM Telepen Output
Original Telepen Output
6 - 22
Download from Www.Somanuals.com. All Manuals Search And Download.
UPC A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will not
transmit it. Default = On.
* On
Off
UPC A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC A data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
6 - 25
Download from Www.Somanuals.com. All Manuals Search And Download.
UPC A Addenda Required
When Addenda Required is set to on, the scanner will only read UPC A bar
codes that have addenda. Default = Not Required.
Required
* Not Required
UPC A Addenda Separator
When this feature is on, there is a space between the data from the bar code
and the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
6 - 26
Download from Www.Somanuals.com. All Manuals Search And Download.
UPC E
<Default All UPC E Settings>
UPC E0 and UPC E1
Most U.P.C. bar codes lead with the 0 number system. For these codes, use
the UPC E0 selection. If you need to read codes that lead with the 1 number
system, use the UPC E1 selection. Default = On (UPC E0) and Off (UPC E1).
* UPC E0 On
UPC E0 Off
UPC E1 On
* UPC E1 Off
6 - 28
Download from Www.Somanuals.com. All Manuals Search And Download.
UPC E0 and UPC E1 Expand
UPC E Expand expands the UPC E code to the 12 digit, UPC A format.
Default = Off.
On
* Off
UPC E0 and UPC E1 Addenda Required
When Addenda Required is set to on, the scanner will only read UPC E bar
codes that have addenda. Default = Not Required.
Required
* Not Required
6 - 29
Download from Www.Somanuals.com. All Manuals Search And Download.
UPC E0 and UPC E1 Addenda Separator
When this feature is on, there is a space between the data from the bar code
and the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
UPC E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at the end
of the scanned data or not. Default = On.
* On
Off
6 - 30
Download from Www.Somanuals.com. All Manuals Search And Download.
UPC E0 Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will not
transmit it. Default = On.
* On
Off
UPC E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC E data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
6 - 31
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN/JAN 13
<Default All EAN/JAN Settings>
EAN/JAN 13
* On
Off
EAN/JAN 13 Check Digit
This selection allows you to specify whether the check digit should be transmit-
ted at the end of the scanned data or not. Default = On.
* On
Off
6 - 32
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN/JAN 13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
EAN/JAN 13 Addenda Required
When Addenda Required is set to on, the scanner will only read EAN/JAN 13
bar codes that have addenda. Default = Not Required.
Required
* Not Required
6 - 33
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN/JAN 13 Addenda Separator
When this feature is on, there is a space between the data from the bar code
and the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
Note: If you want to enable or disable EAN13 with Extended Coupon Code,
ISBN Translate
This selection causes EAN-13 Bookland symbols to be translated into their
equivalent ISBN number format. Default = Off.
On
* Off
EAN/JAN 8
<Default All EAN/JAN 8 Settings>
6 - 34
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN/JAN 8 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
EAN/JAN 8 Addenda Required
When Addenda Required is set to on, the scanner will only read EAN/JAN 8 bar
codes that have addenda. Default = Not Required.
Required
* Not Required
6 - 36
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN/JAN 8 Addenda Separator
When this feature is on, there is a space between the data from the bar code
and the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
MSI
<Default All MSI Settings>
MSI
On
* Off
MSI Check Character
Different types of check characters are used with MSI bar codes. You can
program the scanner to read MSI bar codes with Type 10 check characters.
Default = Validate Type 10, but Don’t Transmit.
6 - 37
Download from Www.Somanuals.com. All Manuals Search And Download.
When Check Character is set to Validate and Transmit, the scanner will only
read MSI bar codes printed with the specified type check character, and will
transmit this character at the end of the scanned data.
When Check Character is set to Validate, but Don’t Transmit, the unit will only
read MSI bar codes printed with the specified type check character, but will not
transmit the check character with the scanned data.
* Validate Type 10, but Don’t
Transmit
Validate Type 10 and Transmit
MSI Message Length
lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Plessey Code
<Default All Plessey Code Settings>
6 - 38
Download from Www.Somanuals.com. All Manuals Search And Download.
Plessey Code
On
* Off
Plessey Message Length
lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
GS1 DataBar Omnidirectional
< Default All GS1 DataBar Omnidirectional Settings >
6 - 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Trioptic Code
Trioptic Code is used for labeling magnetic storage media.
On
Off
GS1 Emulation
The scanner can automatically format the output from any GS1 data carrier to
emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar
symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8,
ITF-14, GS1-128, and GS1-128 DataBar and GS1Composites. If GS1-128
Emulation is selected, the AIM Symbology Identifier will be reported as “]C1”. If
GS1 DataBar Emulation is selected, the AIM Symbology Identifier will be
reported as “]e0.” Any application that accepts GS1 data can be simplified
since it only needs to recognize one data carrier type. Default = GS1 Emulation
Off.
GS1 Data Bar Emulation
GS1-128 Emulation
* GS1 Emulation Off
6 - 46
Download from Www.Somanuals.com. All Manuals Search And Download.
6 - 48
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Interface Keys
Keyboard Function Relationships
The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII
“CTRL”+ relationships apply to all terminals that can be used with the scanner.
ASCII mode.
Function Code
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HEX/ASCII Value
Full ASCII “CTRL” +
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
2
A
B
C
D
E
F
G
H
I
HT
LF
J
VT
K
L
FF
CR
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
\
GS
]
RS
6
US
-
7 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported Interface Keys
IBM AT/XT and
PS/2 Compatibles,
WYSE PC/AT
ASCII
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
Supported Keys
Reserved
Enter (KP)
Cap Lock
ALT make
ALT break
CTRL make
CTRL break
CR/Enter
Reserved
Tab
Reserved
Tab
Delete
CR/Enter
Insert
Escape
F11
Home
Print
Back Space
Back Tab
F12
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
US
* IBM 3191/92, 3471/72, 3196/97, 3476/77,
Telex (all models)
7 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported Interface Keys
Apple Mac/iMac
ASCII
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
7F
Supported Keys
Reserved
Enter/Numpad Enter
CAPS
ALT make
ALT break
CNTRL make
CNTRL break
RETURN
APPLE make
TAB
APPLE break
TAB
Del
RETURN
Ins Help
ESC
F11
Home
Prnt Scrn
BACKSPACE
LSHIFT TAB
F12
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
BACKSPACE
US
DEL
7 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
7 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Utilities
To Add a Test Code I.D. Prefix to All Symbologies
This selection allows you to turn on transmission of a Code I.D. before the
character code that identifies each symbology.) This action first clears all cur-
rent prefixes, then programs a Code I.D. prefix for all symbologies. This is a
temporary setting that will be removed when the unit is power cycled.
Add Code I.D. Prefix to
All Symbologies (Temporary)
Show Software Revision
Scan the bar code below to output the current software revision, unit serial num-
ber, and other product information.
Show Revision
Show Data Format
Scan the bar code below to show current data format settings.
DFMBK3?.
Data Format Settings
EZConfig-Scanning Introduction
EZConfig-Scanning provides a wide range of PC-based programming functions
that can be performed on a scanner connected to your PC's COM port. EZCon-
fig-Scanning allows you to download upgrades to the scanner's firmware,
8 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
change programmed parameters, and create and print programming bar codes.
Using EZConfig-Scanning, you can even save/open the programming parame-
ters for a scanner. This saved file can be e-mailed or, if required, you can cre-
ate a single bar code that contains all the customized programming parameters
and mail or fax that bar code to any location. Users in other locations can scan
the bar code to load in the customized programming.
To communicate with a scanner, EZConfig-Scanning requires that the PC have
at least one available serial communication port, or a serial port emulation using
a physical USB port. If you are using the serial port and RS232 cable, an exter-
nal power supply is required. When using a USB serial port emulation, only a
USB cable is required.
EZConfig-Scanning Operations
The EZConfig-Scanning software performs the following operations:
Scan Data
Scan Data allows you to scan bar codes and display the bar code data
in a window. Scan Data lets you send serial commands to the scanner
and receive scanner response that can be seen in the Scan Data win-
dow. The data displayed in the Scan Data window can either be saved
in a file or printed.
Configure
Configure displays the programming and configuration data of the
scanner. The scanner's programming and configuration data is
grouped into different categories. Each category is displayed as a tree
item under the "Configure" tree node in the application explorer. When
one of these tree nodes is clicked, the right-hand side is loaded with
the parameters' form belonging to that particular category. The "Con-
figure" tree option has all the programming and configuration parame-
ters specified for a scanner. You can set or modify these parameters
as required. You can later write the modified settings to the scanner,
or save them to a dcf file.
Installing EZConfig-Scanning from the Web
2. Click on the Resources tab. Select Download.
3. Click on the dropdown for Select Product Number and select the
number of your product.
4. Under Tools and Utilities, click on the listing for EZConfig for
Scanning.
8 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Follow the security directions as prompted on the screen and click on
Download.
6. When prompted, select Save, and save the file to your desktop.
7. Double click on the EZConfig-Scanning zip file.
8. Double click on the EZConfig-Scanning Setup.exe file. Select Extract
All.
9. Go to the EZConfig-Scanning folder that has been created on your
desktop and double click on the EZConfig-Scanning Setup.exe file.
10. Follow the screen prompts to install the EZConfig-Scanning program.
11. If you’ve selected the defaults during installation, you can click on the
shortcut on your desktop to start EZConfig for Scanning.
Once the software is installed, you may delete the zip file and the EZCon-
fig-Scanning folder from your desktop.
Resetting the Standard Product Defaults
This selection erases all your settings and resets the scanner to the
original factory defaults.
!
If you aren’t sure what programming options are in your scanner, or you’ve
changed some options and want to restore the scanner to factory default set-
tings, first scan the Remove Custom Defaults bar code, then scan Activate
Defaults. This resets the scanner to the factory default settings.
Remove Custom Defaults
Activate Defaults
product default settings for each of the commands (indicated by an asterisk (*)
on the programming pages).
8 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
8 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Serial Programming Commands
The serial programming commands can be used in place of the programming
bar codes. Both the serial commands and the programming bar codes will pro-
gram the scanner. For complete descriptions and examples of each serial pro-
gramming command, refer to the corresponding programming bar code in this
manual.
commands can be sent via a PC com port using terminal emulation software.
Conventions
The following conventions are used for menu and query command descriptions:
parameterA label representing the actual value you should send as part of a
command.
[option] An optional part of a command.
{Data} Alternatives in a command.
bold
Names of menus, menu commands, buttons, dialog boxes, and
windows that appear on the screen.
Menu Command Syntax
Menu commands have the following syntax (spaces have been used for clarity
only):
Prefix Tag SubTag {Data} [, SubTag {Data}] [; Tag SubTag {Data}] […] Storage
Prefix
Tag
Three ASCII characters: SYN M CR (ASCII 22,77,13).
A 3 character case-insensitive field that identifies the desired menu
command group. For example, all RS-232 configuration settings
are identified with a Tag of 232.
SubTag
A 3 character case-insensitive field that identifies the desired menu
command within the tag group. For example, the SubTag for the
RS-232 baud rate is BAD.
Data
The new value for a menu setting, identified by the Tag and Sub-
Tag.
Storage
A single character that specifies the storage table to which the
command is applied. An exclamation point (!) performs the com-
mand’s operation on the device’s volatile menu configuration table.
A period (.) performs the command’s operation on the device’s
non-volatile menu configuration table. Use the non-volatile table
only for semi-permanent changes you want saved through a power
cycle.
9 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Query Commands
Several special characters can be used to query the device about its settings.
^
?
*
What is the default value for the setting(s).
What is the device’s current value for the setting(s).
What is the range of possible values for the setting(s). (The de-
vice’s response uses a dash (-) to indicate a continuous range of
values. A pipe (|) separates items in a list of non-continuous val-
ues.)
Tag Field Usage
When a query is used in place of a Tag field, the query applies to the entire set
of commands available for the particular storage table indicated by the Storage
field of the command. In this case, the SubTag and Data fields should not be
used because they are ignored by the device.
SubTag Field Usage
When a query is used in place of a SubTag field, the query applies only to the
subset of commands available that match the Tag field. In this case, the Data
field should not be used because it is ignored by the device.
Data Field Usage
When a query is used in place of the Data field, the query applies only to the
specific command identified by the Tag and SubTag fields.
Concatenation of Multiple Commands
Multiple commands can be issued within one Prefix/Storage sequence. Only
the Tag, SubTag, and Data fields must be repeated for each command in the
sequence. If additional commands are to be applied to the same Tag, then the
new command sequence is separated with a comma (,) and only the SubTag
and Data fields of the additional command are issued. If the additional com-
mand requires a different Tag field, the command is separated from previous
commands by a semicolon (;).
Responses
The device responds to serial commands with one of three responses:
ACK
ENQ
NAK
Indicates a good command which has been processed.
Indicates an invalid Tag or SubTag command.
Indicates the command was good, but the Data field entry was out of
the allowable range for this Tag and SubTag combination, e.g., an entry
for a minimum message length of 100 when the field will only accept 2
characters.
When responding, the device echoes back the command sequence with the
status character inserted directly before each of the punctuation marks (the
period, exclamation point, comma, or semicolon) in the command.
9 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Examples of Query Commands
In the following examples, a bracketed notation [ ] depicts a non-displayable
response.
Example: Example #1:What is the range of possible values for Codabar
Coding Enable?
Enter:
cbrena*.
Response: CBRENA0-1[ACK]
This response indicates that Codabar Coding Enable (CBRENA) has a range of
values from 0 to 1 (off and on).
Example: Example #2: What is the default value for Codabar Coding Enable?
Enter:
cbrena^.
Response: CBRENA1[ACK]
This response indicates that the default setting for Codabar Coding Enable
(CBRENA) is 1, or on.
Example: Example #3: What is the device’s current setting for Codabar
Coding Enable?
Enter:
cbrena?.
Response: CBRENA1[ACK]
This response indicates that the device’s Codabar Coding Enable (CBRENA) is
set to 1, or on.
Example: Example #4: What are the device’s settings for all Codabar
selections?
Enter:
cbr?.
Response: CBRENA1[ACK],
SSX0[ACK],
CK20[ACK],
CCT1[ACK],
MIN2[ACK],
MAX60[ACK],
DFT[ACK].
This response indicates that the device’s Codabar Coding Enable (CBRENA) is
set to 1, or on;
the Start/Stop Character (SSX) is set to 0, or Don’t Transmit;
the Check Character (CK2) is set to 0, or Not Required;
concatenation (CCT) is set to 1, or Enabled;
the Minimum Message Length (MIN) is set to 2 characters;
the Maximum Message Length (MAX) is set to 60 characters;
and the Default setting (DFT) has no value.
9 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Trigger Commands
You can activate and deactivate the scanner with serial trigger commands.
First, the scanner must be put in Manual/Serial Trigger Mode either by scanning
the trigger is activated and deactivated by sending the following commands:
Activate:SYN T CR
Deactivate:SYN U CR
The scanner scans until a bar code has been read, until the deactivate com-
mand is sent, or until the serial time-out has been reached (see Read Time-
Resetting the Standard Product Defaults
If you aren’t sure what programming options are in your scanner, or you’ve
changed some options and want the factory settings restored, scan the Stan-
dard Product Default Settings bar code below.
Standard Product Default Settings
The chart on the following pages lists the factory default settings for each of the
menu commands (indicated by an asterisk (*) on the programming pages).
9 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Commands
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Product Default Settings
Setting Custom
Defaults
Set Custom Defaults
MNUCDF
DEFALT
Resetting the Custom
Defaults
Activate Custom
Defaults
Programming the Interface
Plug and Play Codes
Keyboard Wedge: IBM
PAP_AT
PC AT and
Compatibles with CR
suffix
Laptop Direct Connect PAPLTD
RS232 Serial Port
PAP232
PAPP5B
PAP9B1
Plug and Play Codes:
RS485
IBM Port 5B Interface
IBM Port 9B HHBCR-1
Interface
IBM Port 17 Interface
PAPP17
PAP9B2
IBM Port 9B HHBCR-2
Interface
OPOS Mode
PAPOPS
PAPSPH
Plug and Play Codes:
IBM SurePos
USB IBM SurePos
Handheld
USB IBM SurePos
Tabletop
PAPSPT
Plug and Play Codes:
USB
USB Keyboard (PC)
USB Keyboard (Mac)
USB HID POS
PAP124
PAP125
PAP131
9 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
USB Serial
Commands
USB Serial Emulation
PAP130
CTS/RTS Emulation
On
USBCTS1
*CTS/RTS Emulation
Off
USBCTS0
ACK/NAK Mode On
*ACK/NAK Mode Off
USBACK1
USBACK0
PAPBIO
Plug and Play Codes:
Honeywell Bioptic Aux
Port
Datalogic Magellan
Bioptic Aux Port
PAPMAG
Wincor Mode A
*U.S.A.
PAPWMA
KBDCTY0
Program Keyboard
Country
Albania
KBDCTY35
KBDCTY91
KBDCTY81
KBDCTY80
KBDCTY82
KBDCTY1
Arabic
Azeri (Cyrillic)
Azeri (Latin)
Belarus
Belgium
Bosnia
KBDCTY33
KBDCTY16
KBDCTY59
KBDCTY52
KBDCTY53
KBDCTY54
Brazil
Brazil (MS)
Bulgaria (Cyrillic)
Bulgaria (Latin)
Canada (French
legacy)
Canada (French)
Canada (Multilingual)
China
KBDCTY18
KBDCTY55
KBDCTY92
KBDCTY32
KBDCTY15
Croatia
Czech
9 - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Czech (Programmers)
Czech (QWERTY)
Czech (QWERTZ)
Denmark
KBDCTY40
KBDCTY39
KBDCTY38
KBDCTY8
Dutch (Netherlands)
Estonia
KBDCTY11
KBDCTY41
KBDCTY83
KBDCTY2
Faroese
Finland
France
KBDCTY3
Gaelic
KBDCTY84
KBDCTY4
Germany
Greek
KBDCTY17
KBDCTY64
KBDCTY61
KBDCTY65
KBDCTY62
KBDCTY63
KBDCTY66
KBDCTY60
KBDCTY12
KBDCTY50
KBDCTY19
KBDCTY75
KBDCTY73
KBDCTY56
KBDCTY5
Greek (220 Latin)
Greek (220)
Greek (319 Latin)
Greek (319)
Greek (Latin)
Greek (MS)
Greek (Polytonic)
Hebrew
Hungarian (101 key)
Hungary
Iceland
Ireland
Italian (142)
Italy
Japan ASCII
Kazakh
KBDCTY28
KBDCTY78
KBDCTY93
KBDCTY79
KBDCTY14
Korea
Kyrgyz (Cyrillic)
Latin America
9 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Latvia
KBDCTY42
KBDCTY43
KBDCTY44
KBDCTY45
KBDCTY34
KBDCTY74
KBDCTY86
KBDCTY9
Latvia (QWERTY)
Lithuania
Lithuania (IBM)
Macedonia
Malta
Mongolian (Cyrillic)
Norway
Poland
KBDCTY20
KBDCTY57
KBDCTY58
KBDCTY13
KBDCTY25
KBDCTY26
KBDCTY67
KBDCTY68
KBDCTY21
KBDCTY37
KBDCTY36
KBDCTY22
KBDCTY49
KBDCTY48
KBDCTY31
KBDCTY10
KBDCTY51
KBDCTY23
KBDCTY29
KBDCTY6
Polish (214)
Polish (Programmers)
Portugal
Romania
Russia
Russian (MS)
Russian (Typewriter)
SCS
Serbia (Cyrillic)
Serbia (Latin)
Slovakia
Slovakia (QWERTY)
Slovakia (QWERTZ)
Slovenia
Spain
Spanish variation
Sweden
Switzerland (French)
Switzerland (German)
Tatar
KBDCTY85
KBDCTY94
KBDCTY27
Thailand
Turkey F
9 - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Turkey Q
KBDCTY24
KBDCTY76
KBDCTY7
KBDCTY89
Ukrainian
United Kingdom
United Stated (Dvorak
right)
United States (Dvorak
left)
KBDCTY88
United States (Dvorak) KBDCTY87
United States
(International)
KBDCTY30
Uzbek (Cyrillic)
Vietnam
KBDCTY77
KBDCTY95
KBDSTY0
KBDALT0
KBDALT7
KBDSTY1
KBDSTY2
KBDSTY6
KBDSTY7
ALT Mode
*Off
4 Characters
*Regular
Keyboard Style
Caps Lock
Shift Lock
Automatic Caps Lock
Autocaps via
NumLock
Emulate External
Keyboard
KBDSTY5
KBDCAS2
Keyboard Modifiers
Windows Mode
Control + X Mode On
*Control + X Off
KBDCAS0
KBDCAS1
DOS Mode Control +
X Mode On
Windows Mode Prefix/ KBDCAS3
Suffix Off
9 - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
*Numeric Keypad Off
Numeric Keypad On
*Auto Direct Conn. Off
Auto Direct Conn. On
RS-232
KBDNPS0
KBDNPS1
KBDADC0
KBDADC1
PAP232
Serial Port Connection
Baud Rate
300 BPS
232BAD0
232BAD1
232BAD2
232BAD3
232BAD4
232BAD5
232BAD6
232BAD7
232BAD8
232BAD9
232WRD0
600 BPS
1200 BPS
2400 BPS
4800 BPS
9600 BPS
19200 BPS
*38400 BPS
57600 BPS
115200 BPS
Word Length: Data
Bits, Stop Bits, and
Parity
7 Data, 1 Stop, Parity
None
7 Data, 1 Stop, Parity
Even
232WRD3
232WRD6
7 Data, 1 Stop, Parity
Odd
7 Data, 2 Stop, Parity
None
232WRD1
232WRD4
232WRD7
232WRD2
232WRD5
7 Data, 2 Stop, Parity
Even
7 Data, 2 Stop, Parity
Odd
*8 Data, 1 Stop, Parity
None
8 Data, 1 Stop, Parity
Even
9 - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
8 Data, 1 Stop, Parity
Odd
232WRD8
RS-232 Handshaking
*RTS/CTS Off
232CTS0
RTS/CTS Off, RTS
Inactive
232CTS10
Flow Control, No
Timeout
232CTS1
232CTS7
232CTS2
232CTS3
232CTS4
232CTS5
Character-Based Flow
Control, No Timeout
Two-Direction Flow
Control
Flow Control with
Timeout
Character-Based Flow
Control with Timeout
CTS-Based Flow
Control, No Timeout
RTS On
232CTS8
232CTS9
232XON0
232DEL####
232XON1
232ACK0
232ACK1
232PKT0
232PKT1
No RTS if CTS is On
*XON/XOFF Off
RS232 Timeout
XON/XOFF On
*ACK/NAK Off
ACK/NAK On
Scanner-Bioptic
Packet Mode
*Packet Mode Off
Packet Mode On
Output Selections
Beeper - Good Read
Off
BEPBEP0
BEPBEP1
*On
9 - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Beeper Volume - Good
Read
Off
BEPLVL0
Low
BEPLVL1
Medium
BEPLVL2
*High
BEPLVL3
Beeper Pitch - Good
Read (Frequency)
Low (1600 Hz)
*Medium (2750 Hz)
High (4200 Hz)
*Normal Beep
Short Beep
*Razz (100 Hz)
*Medium (2000 Hz)
High (4200 Hz)
Off
BEPFQ11600
BEPFQ12750
BEPFQ14200
BEPBIP0
Beeper Duration -
Good Read
BEPBIP1
Beeper Pitch - Error
BEPFQ2100
BEPFQ22000
BEPFQ24200
BEPLED0
LED - Good Read
*On
BEPLED1
Number of Beeps -
Good Read
*1
BEPRPT1
Range 1 - 9
*No Delay
Short Delay (500 ms)
BEPRPT#
Good Read Delay
DLYGRD0
DLYGRD500
DLYGRD1000
Medium Delay (1000
ms)
Long Delay (1500 ms)
Range 0 - 30,000 ms
DLYGRD1500
User-Specified Good
Read Delay
9 - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Trigger Mode
*Manual/Serial Trigger
TRGMOD0
Read Time-Out (0 -
300,000 ms) *30,000
TRGSTO####
Automatic Trigger
Presentation Mode
TRGMOD1
TRGMOD3
ILLAON1
Continuous
Illumination On
*Continuous
Illumination Off
ILLAON0
Hands Free Time-Out
(0-300,000 seconds)
*5000
TRGPTO####
##
Reread Delay
Short (500 ms)
DLYRRD500
DLYRRD750
DLYRRD1000
DLYRRD3000
*Medium (750 ms)
Long (1000 ms)
Extra Long (2000 ms)
Range 0 - 30,000 ms
User-Specified Reread
Delay
Centering
Centering On
*Centering Off
DECWIN1
DECWIN0
DECLFT###
Left of Centering
Window *40
Right of Centering
Window *60
DECRGT###
Output Sequence
Editor
Enter Sequence
Default Sequence
Required
SEQBLK
SEQDFT
Require Output
Sequence
SEQ_EN2
SEQ_EN1
SEQ_EN0
SHOTGN1
SHOTGN0
On/Not Required
*Off
Multiple Symbols
On
*Off
9 - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
No Read
On
SHWNRD1
SHWNRD0
VIDREV1
VIDREV0
*Off
On
Video Reverse
*Off
Prefix/Suffix Selections
Add CR Suffix to All Symbologies
VSUFCR
PREBK2##
PRECL2
Prefix
Add Prefix
Clear One Prefix
Clear All Prefixes
Add Suffix
PRECA2
SUFBK2##
SUFCL2
Suffix
Clear One Suffix
Clear All Suffixes
SUFCA2
KBDEXT0
Transmit Alternative
Extended ASCII
Characters
Transmit Alternate
Extended ASCII
*Transmit Normal
Extended ASCII
KBDEXT1
Function Code
Transmit
*Enable
Disable
RMVFNC0
RMVFNC1
DLYCHR##
DLYCRX##
DLY_XX###
Intercharacter Delay
User Specified
Intercharacter Delay
Delay Length
Character to Trigger
Delay
Interfunction Delay
Intermessage Delay
DLYFNC##
DLYMSG##
Data Formatter Selections
Data Format Editor *Default Data Format
DFMDF3
(None)
Enter Data Format
DFMBK3##
DFMCL3
Clear One Data
Format
Clear All Data Formats DFMCA3
9 - 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Data Formatter
Off
DFM_EN0
DFM_EN1
DFM_EN2
*On, but Not Required
On, Required
Symbologies
All Symbologies
All Symbologies Off
All Symbologies On
ALLENA0
ALLENA1
CBRDFT
Codabar
Codabar
Default All Codabar
Settings
Off
CBRENA0
CBRENA1
CBRSSX0
CBRSSX1
CBRCK20
CBRCK21
*On
Codabar Start/Stop
Char.
*Don’t Transmit
Transmit
Codabar Check Char.
*No Check Char.
Validate, But Don’t
Transmit
Validate, and Transmit
*Off
CBRCK22
CBRCCT0
CBRCCT1
CBRCCT2
CBRMIN##
CBRMAX##
C39DFT
Codabar
Concatenation
On
Require
Codabar Message
Length
Minimum (2 - 60) *4
Maximum (2 - 60) *60
Code 39
Default All Code 39
Settings
Code 39
Off
C39ENA0
C39ENA1
C39SSX0
C39SSX1
C39CK20
C39CK21
*On
Code 39 Start/Stop
Char.
*Don’t Transmit
Transmit
Code 39 Check Char.
*No Check Char.
Validate, But Don’t
Transmit
Validate,
C39CK22
and Transmit
9 - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Code 39 Message
Length
Minimum (0 - 48) *0
C39MIN##
C39MAX##
C39APP0
C39APP1
C39B320
C39B321
Maximum (0 - 48) *48
Code 39 Append
*Off
On
Code 32
Pharmaceutical
(PARAF)
*Off
On
Code 39 Full ASCII
*Off
On
C39ASC0
C39ASC1
I25DFT
Interleaved 2 of 5
Interleaved 2 of 5
Default All Interleaved
2 of 5 Settings
Off
I25ENA0
I25ENA1
I25CK20
I25CK21
*On
Interleaved 2 of 5
Check Digit
*No Check Char.
Validate, But Don’t
Transmit
Validate, and Transmit
Minimum (2 - 80) *4
Maximum (2 - 80) *80
I25CK22
I25MIN##
I25MAX##
C93DFT
Interleaved 2 of 5
Message Length
Code 93
Default All Code 93
Settings
Code 93
Off
C93ENA0
C93ENA1
C93MIN##
C93MAX##
R25DFT
*On
Code 93 Message
Length
Minimum (0 - 80) *0
Maximum (0 - 80) *80
Straight 2 of 5
Industrial
Default All Straight 2 of
5
Settings
Straight 2 of 5
Industrial
Off
R25ENA0
R25ENA1
R25MIN##
R25MAX##
*On
Straight 2 of 5
Industrial Message
Length
Minimum (1 - 48) *4
Maximum (1 - 48) *48
9 - 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Straight 2 of 5 IATA
Default All Straight 2 of
5 IATA
A25DFT
Settings
Straight 2 of 5 IATA
*Off
A25ENA0
A25ENA1
A25MIN##
A25MAX##
X25DFT
On
Straight 2 of 5 IATA
Message Length
Minimum (1 - 48) *4
Maximum (1 - 48) *48
Matrix 2 of 5
Default All Matrix 2 of
5
Settings
Matrix 2 of 5
*Off
X25ENA0
X25ENA1
X25MIN##
X25MAX##
C11DFT
On
Matrix 2 of 5 Message
Length
Minimum (1 - 80) *4
Maximum (1 - 80) *80
Code 11
Default All Code 11
Settings
Code 11
*Off
C11ENA0
C11ENA1
C11CK20
C11CK21
C11MIN##
C11MAX##
128DFT
On
Code 11 Check Digits
Required
1 Check Digit
*2 Check Digits
Minimum (1 - 80) *4
Maximum (1 - 80) *80
Code 11 Message
Length
Code 128
Default All Code 128
Settings
Code 128
Off
128ENA0
128ENA1
ISBENA1
ISBENA0
128MIN##
128MAX##
128DCP
*On
ISBT Concatenation
On
*Off
Code 128 Message
Length
Minimum (0 - 80) *0
Maximum (0 - 80) *80
Code 128 Code Page
Code 128 Code Page
9 - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Code 128 Function
Code Transmit
*Off
On
128FNX0
128FNX1
TELDFT
Telepen
Default All Telepen
Settings
Telepen
*Off
TELENA0
TELENA1
TELOLD0
TELOLD1
On
Telepen Output
*AIM Telepen Output
Original Telepen
Output
Telepen Message
Length
Minimum (1 - 60) *1
Maximum (1 - 60) *60
TELMIN##
TELMAX##
UPADFT
UPC A
Default All
UPC A Settings
UPC A
Off
UPAENA0
UPAENA1
UPACKX0
UPACKX1
UPANSX0
UPANSX1
UPAAD20
UPAAD21
UPAAD50
UPAAD51
UPAARQ0
UPAARQ1
UPAADS0
UPAADS1
CPNENA0
CPNENA1
*On
UPC A Check Digit
Off
*On
UPC A Number
System
Off
*On
UPC A 2 Digit
Addenda
*Off
On
UPC A 5 Digit
Addenda
*Off
On
UPC A Addenda
Required
*Not Required
Required
Off
UPC A Addenda
Separator
*On
UPC-A/EAN-13 with
Extended Coupon
Code
*Off
On
9 - 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
UPC E
Default All UPC E
Settings
UPEDFT
UPC E0
Off
UPEEN00
UPEEN01
UPEEN10
UPEEN11
UPEEXP0
UPEEXP1
UPECKX0
UPECKX1
UPENSX0
UPENSX1
UPEAD20
UPEAD21
UPEAD50
UPEAD51
UPEARQ0
UPEARQ1
UPEADS0
UPEADS1
E13DFT
*On
UPC E1
*Off
On
UPC E Expand
UPC E Check Digit
*Off
On
Off
*On
UPC E Number
System
Off
*On
UPC E 2 Digit
Addenda
*Off
On
UPC E 5 Digit
Addenda
*Off
On
UPC E Addenda
Required
*Not Required
Required
Off
UPC E Addenda
Separator
*On
EAN/JAN 13
Default All EAN/
JAN 13 Settings
EAN/JAN 13
Off
E13ENA0
E13ENA1
E13CKX0
E13CKX1
E13AD20
E13AD21
E13AD50
E13AD51
*On
Off
EAN/JAN 13 Check
Digit
*On
*Off
On
EAN/JAN 13 2 Digit
Addenda
EAN/JAN 13 5 Digit
Addenda
*Off
On
9 - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
EAN/JAN 13 Addenda
Required
*Not Required
E13ARQ0
E13ARQ1
E13ADS0
E13ADS1
E13ISB0
E13ISB1
EA8DFT
Required
Off
EAN/JAN 13 Addenda
Separator
*On
ISBN Translate
*Off
On
EAN/JAN 8
EAN/JAN 8
Default All EAN/
JAN 8 Settings
Off
EA8ENA0
EA8ENA1
EA8CKX0
EA8CKX1
EA8AD20
EA8AD21
EA8AD50
EA8AD51
EA8ARQ0
EA8ARQ1
EA8ADS0
EA8ADS1
MSIDFT
*On
EAN/JAN 8 Check
Digit
Off
*On
EAN/JAN 8 2 Digit
Addenda
*Off
On
EAN/JAN 8 5 Digit
Addenda
*Off
On
EAN/JAN 8 Addenda
Required
*Not Required
Required
Off
EAN/JAN 8 Addenda
Separator
*On
MSI
Default All MSI
Settings
MSI
*Off
On
MSIENA0
MSIENA1
MSICHK0
MSI Check Character
*Validate Type 10, but
Don’t Transmit
Validate Type 10 and
Transmit
MSICHK1
MSI Message Length
Plessey Code
Minimum (4 - 48) *4
Maximum (4 - 48) *48
MSIMIN##
MSIMAX##
PLSDFT
Default All Plessey
Settings
9 - 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Plessey Code
*Off
PLSENA0
PLSENA1
PLSMIN##
PLSMAX##
RSSDFT
On
Plessey Message
Length
Minimum (4 - 48) *4
Maximum (4 - 48) *48
GS1 DataBar
Default All
Omnidirectional
GS1 DataBar
Omnidirectional
Settings
GS1 DataBar
Omnidirectional
Off
RSSENA0
RSSENA1
RSLDFT
*On
GS1 DataBar Limited
Default All GS1
DataBar
Limited Settings
GS1 DataBar Limited
Off
RSLENA0
RSLENA1
RSEDFT
*On
GS1 DataBar
Expanded
Default All GS1
DataBar
Expanded Settings
GS1 DataBar
Expanded
Off
RSEENA0
RSEENA1
RSEMIN##
RSEMAX##
*On
GS1 DataBar
Expanded Msg.
Length
Minimum (4 - 74) *4
Maximum (4 - 74) *74
China Post Code
Default All China Post
Code Settings
CPCDFT
China Post Code
*Off
CPCENA0
CPCENA1
CPCMIN##
CPCMAX##
CPCDFT
On
China Post Code Msg.
Length
Minimum (2 - 80) *4
Maximum (2 - 80) *80
Korea Post Code
Default All Korea Post
Code Settings
Korea Post Code
*Off
On
CPCENA0
CPCENA1
9 - 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial
Setting
* Indicates default
Command
# Indicates a
numeric entry
Selection
Page
Korea Post Code Msg.
Length
Minimum (2 - 80) *4
Maximum (2 - 80) *80
CPCMIN##
CPCMAX##
CBFDFT
Codablock F
Default All Codablock
F Settings
Codablock F
*Off
CBFENA0
On
CBFENA1
Codablock F Msg.
Length
Minimum (1 - 2048) *1
CBFMIN####
CBFMAX####
Maximum (1 - 2048)
*2048
Code 49
Code 49
Default All Code 49
Settings
C49DFT
* Off
C49ENA0
C49ENA1
C49MIN##
C49MAX##
EANEMU2
EANEMU1
EANEMU0
LBLENA0
LBLENA1
On
Code 49
Minimum (1 - 81) *1
Maximum (1 - 81) *81
GS1 Emulation
GS1-128 Emulation
*GS1 Emulation Off
*Off
GS1 Emulation
Label Code
On
9 - 22
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Product Specifications
Hyperion 1300g Product Specifications
Parameter
Specification
Mechanical
Height
5.9 inches (15 cm)
4.4 inches (11.2 cm)
3.1 inches (7.9 cm)
5.6 ounces (160 g)
Length
Width
Weight
Electrical
LED source
Input Voltage
Operating Power
Standby Power
Environmental
Operating Temperature
Storage Temperature
Humidity
630 nm visible red LED
4.5-5.5VDC at imager
200mA @ 5V
125mA @5V
32 F to +122 F (0 C to +50 C)
-40 F to +140 F (-40 C to +60 C)
0 to 95% non-condensing
Operational after 50 drops from 5 feet
(1.5 m) to concrete
Drop
Environmental Sealing
Light Levels
IP41
70,000 lux
ESD
15 kV to any external surface
IP41
Sealant Rating
Scan Performance
Scan Pattern
Single Line
Motion Tolerance
Scan Rate
20 inches (51 cm) per second
Up to 270 scans per second
Print Contrast
Pitch, Skew
20%
65
Reads standard 1D and GS1 DataBar
symbologies
Decode Capabilities
Use only a Listed Limited Power Source (LPS) or
Class 2 type power supply with output rated 5 to
5.2Vdc, 1A
Optional External Power Supply
Requirements
10 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Connector Pinouts
Keyboard Wedge
10 Pin RJ41 Modular Plug - connects to the scanner handle
1
2
3
4
5
6
7
8
9
10
Cable shield
Cable select
Supply ground
Terminal data
Terminal clock
Keyboard clock
+5V power
Keyboard data
Serial Output
10 Pin RJ41 Modular Plug - connects to the scanner handle
1
2
3
4
5
6
7
8
9
10
Cable shield
Cable select
Supply ground
Transmit data
Receive data - serial data to scanner
CTS
+5V power
RTS
USB
10 Pin Modular Plug - connects to the scanner handle
1
2
3
4
5
6
7
8
9
Cable shield
Cable select
Supply ground
+5V power
Data +
10 Data -
10 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Required Safety Label Locations
Light Source
Item
Number,
Serial
Number
and
Revision
Compliance
Label location
10 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
10 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Maintenance
Repairs
Repairs and/or upgrades are not to be performed on this product. These ser-
Maintenance
Your device provides reliable and efficient operation with a minimum of care.
Although specific maintenance is not required, the following periodic checks
ensure dependable scanner operation:
Cleaning the Device
Reading performance may degrade if the scanner’s window is not clean. If the
window is visibly dirty, or if the scanner isn’t operating well, clean the window
with a soft cloth or lens tissue dampened with water (or a mild soapy water solu-
tion). If a soapy water solution is used, rinse with a clean lens tissue dampened
with water only.
The scanner’s housing may also be cleaned the same way.
Caution:
!
Do not submerge the scanner in water. Do not use
abrasive wipes or tissues on the scanner’s window –
abrasive wipes may scratch the window.
Never use solvents (e.g., acetone, benzene, ether, or
phenol-based agents) on the housing or window –
solvents may damage the finish or the window.
Inspecting Cords and Connectors
Inspect the scanner’s interface cable and connector for wear or other signs of
damage. A badly worn cable or damaged connector may interfere with scanner
operation. Contact your Honeywell distributor for information about cable
11 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Interface Cable
The standard interface cable is attached to the scanner with an 10-pin modular
connector. When properly seated, the connector is held in the scanner’s handle
by a flexible retention tab. The interface cable is designed to be field replace-
able.
•
•
Order replacement cables from Honeywell or from an authorized distributor.
When ordering a replacement cable, specify the cable part number of the
original interface cable.
Replacing the Interface Cable:
1. Turn the power to the host system
OFF.
2. Disconnect the scanner’s cable from
the terminal or computer.
3. Locate the small hole on the side of
the scanner’s handle. This is the
cable release.
4. Straighten one end of a paper clip.
5. Insert the end of the paper clip into the
small hole and press in. This
depresses the retention tab, releasing
the connector. Pull the connector out
while maintaining pressure on the
paper clip, then remove the paper clip.
Cable
Release
6. Replace with the new cable.
Insert the connector into the opening
and press firmly. The connector is
keyed to go in only one way, and will click into place.
Troubleshooting
The scanner automatically performs self-tests whenever you turn it on. If your
scanner is not functioning properly, review the following Troubleshooting Guide
to try to isolate the problem.
Is the power on? Is the aiming beam line on?
If the aiming beam line isn’t illuminated, check that:
•
•
•
The cable is connected properly.
The host system power is on (if external power isn’t used).
The trigger works.
11 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Is the scanner having trouble reading your symbols?
If the scanner isn’t reading symbols well, check that the symbols:
•
•
•
Aren’t smeared, rough, scratched, or exhibiting voids.
Aren’t coated with frost or water droplets on the surface.
Are enabled in the scanner or in the decoder to which the scanner connects.
Is the bar code displayed but not entered?
The bar code is displayed on the host device correctly, but you still have to press
a key to enter it (the Enter/Return key or the Tab key, for example).
You need to program a suffix. Programming a suffix enables the scanner to out-
put the bar code data plus the key you need (such as “CR”) to enter the data
information.
Does the scanner read the bar code incorrectly?
If the scanner reads a bar code, but the data is not displayed correctly on the
host screen:
•
The scanner may not be programmed for the appropriate terminal interface.
For example, you scan “12345” and the host displays “@es%.”
Reprogram the scanner with the correct Plug and Play or Terminal selection
•
The scanner may not be programmed to output your bar code data properly.
For example, you scan “12345” and the host displays “A12345B.”
Reprogram the scanner with the proper symbology selections. See
The scanner won’t read your bar code at all.
1. Scan the sample bar codes in the back of this manual. If the scanner reads
the sample bar codes, check that your bar code is readable.
If you aren’t sure what programming options have been set in the scanner, or if
you want the factory default settings restored, scan Resetting the Custom
11 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
11 - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Customer Support
Technical Assistance
If you need assistance installing or troubleshooting your device, please contact
us by using one of the methods below:
Knowledge Base: www.hsmknowledgebase.com
Our Knowledge Base provides thousands of immediate solutions. If the
Knowledge Base cannot help, our Technical Support Portal (see below)
provides an easy way to report your problem or ask your question.
Technical Support Portal: www.hsmsupportportal.com
The Technical Support Portal not only allows you to report your problem, but it
also provides immediate solutions to your technical issues by searching our
Knowledge Base. With the Portal, you can submit and track your questions
online and send and receive attachments.
Web form: www.hsmcontactsupport.com
You can contact our technical support team directly by filling out our online
support form. Enter your contact details and the description of the question/
problem.
Telephone: www.honeywellaidc.com/locations
For our latest contact information, please check our website at the link above.
Limited Warranty
Honeywell International Inc. ("HII") warrants its products and optional accesso-
ries to be free from defects in materials and workmanship and to conform to
HII’s published specifications applicable to the products purchased at the time
of shipment. This warranty does not cover any HII product which is (i) improp-
erly installed or used; (ii) damaged by accident or negligence, including failure
to follow the proper maintenance, service, and cleaning schedule; or (iii) dam-
aged as a result of (A) modification or alteration by the purchaser or other party,
(B) excessive voltage or current supplied to or drawn from the interface connec-
tions, (C) static electricity or electro-static discharge, (D) operation under condi-
tions beyond the specified operating parameters, or (E) repair or service of the
product by anyone other than HII or its authorized representatives.
This warranty shall extend from the time of shipment for the duration published
by HII for the product at the time of purchase ("Warranty Period"). Any defective
product must be returned (at purchaser’s expense) during the Warranty Period
to HII factory or authorized service center for inspection. No product will be
accepted by HII without a Return Materials Authorization, which may be
obtained by contacting HII. In the event that the product is returned to HII or its
authorized service center within the Warranty Period and HII determines to its
satisfaction that the product is defective due to defects in materials or workman-
12 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
ship, HII, at its sole option, will either repair or replace the product without
charge, except for return shipping to HII.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE
FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR
WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR NON-
INFRINGEMENT.
HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER
THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE
DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS. IN NO
EVENT SHALL HII BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSE-
QUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY OF HII
ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUNDER
(WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED ON CON-
TRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE ACTUAL
AMOUNT PAID TO HII FOR THE PRODUCT. THESE LIMITATIONS ON LIA-
BILITY SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HII MAY
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES,
OR DAMAGES. SOME STATES, PROVINCES, OR COUNTRIES DO NOT
ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU.
All provisions of this Limited Warranty are separate and severable, which
means that if any provision is held invalid and unenforceable, such determina-
tion shall not affect the validity of enforceability of the other provisions hereof.
Use of any peripherals not provided by the manufacturer may result in damage
not covered by this warranty. This includes but is not limited to: cables, power
supplies, cradles, and docking stations. HII extends these warranties only to the
first end-users of the products. These warranties are non-transferable.
The duration of the limited warranty for the Hyperion 1300g is five (5) years.
12 - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Appendix A
Symbology Charts
Note: “ m” represents the AIM modifier character. Refer to International
Technical Specification, Symbology Identifiers, for AIM modifier character
details.
Prefix/Suffix entries for specific symbologies override the universal (All
Symbologies, 99) entry.
page 5-1 for information about using Code ID and AIM ID.
Linear Symbologies
AIM
Honeywell
Hex
Possible
modifiers
(m)
Symbology
ID
ID
All Symbologies
Codabar
99
61
68
6A
3C
]Fm
]H3
]Cm
]X0
0-1
a
h
j
Code 11
Code 128
0, 1, 2, 4
Code 32 Pharmaceutical
(PARAF)
<
Code 39 (supports Full ASCII
mode)
]Am
]L2
0, 1, 3, 4, 5, 7
b
T
i
62
54
69
TCIF Linked Code 39
(TLC39)
Code 93 and 93i
]Gm
]Em
0-9, A-Z,
a-m
EAN
0, 1, 3, 4
d
d
64
64
EAN-13 (including Bookland ]E0
EAN)
EAN-13 with Add-On
]E3
]E3
d
d
64
64
EAN-13 with Extended
Coupon Code
EAN-8
]E4
D
44
A - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
AIM
Honeywell
Possible
modifiers
(m)
Symbology
ID
ID
Hex
EAN-8 with Add-On
GS1
GS1 DataBar
]E3
D
44
]em
]em
]em
]C1
0
y
{
}
I
79
7B
7D
49
GS1 DataBar Limited
GS1 DataBar Expanded
GS1-128
2 of 5
China Post (Hong Kong 2 of ]X0
5)
Q
51
Interleaved 2 of 5
Matrix 2 of 5
]Im
0, 1, 3
e
m
Y
f
65
6D
59
66
66
67
]X0
]X0
]Rm
]S0
]Mm
NEC 2 of 5
Straight 2 of 5 IATA
Straight 2 of 5 Industrial
0, 1, 3
0, 1
f
MSI
UPC
g
0, 1, 2, 3, 8,
9, A, B, C
UPC-A
]E0
]E3
]E3
c
c
c
63
63
63
UPC-A with Add-On
UPC-A with Extended
Coupon Code
UPC-E
]E0
]E3
]X0
E
E
E
45
45
45
UPC-E with Add-On
UPC-E1
Add Honeywell Code ID
Add AIM Code ID
Add Backslash
5C80
5C81
5C5C
A - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Postal Symbologies
AIM
Honeywell
Hex
Possible
modifiers
(m)
Symbology
ID
ID
All Symbologies
Australian Post
British Post
99
41
42
43
51
2c
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
A
B
C
Q
,
Canadian Post
China Post
InfoMail
Intelligent Mail Bar Code
Japanese Post
KIX (Netherlands) Post
Korea Post
M
J
4D
4A
4B
3F
4C
4E
50
K
?
Planet Code
L
Postal-4i
N
P
Postnet
ASCII Conversion Chart (Code Page 1252)
In keyboard applications, ASCII Control Characters can be represented in 3 dif-
ferent ways, as shown below. The CTRL+X function is OS and application
dependent. The following table lists some commonly used Microsoft functional-
ity. This table applies to U.S. style keyboards. Certain characters may differ
depending on your Country Code/PC regional settings..
Non-printable
ASCII control
Keyboard Control + ASCII (CTRL+X) mode
characters
ON (KBDCAS1)
CTRL+'X'
OFF (KBDCAS0)
Control
Control
Character Output
Off (KBDNPE0)
CTRL+ X
function
Character
Output On
(KBDNPE1)
DEC HEX Char
0
1
00
01
NUL
SOH
CTRL+ @
CTRL+ A
Reserved
NP Enter
Txt: [NUL]
Txt: [SOH]
Select all
A - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2
02
03
04
05
06
07
08
09
0A
0B
STX
ETX
EOT
ENQ
ACK
BEL
BS
CTRL+ B
CTRL+ C
CTRL+ D
CTRL+ E
CTRL+ F
CTRL+ G
CTRL+ H
CTRL+ I
CTRL+ J
CTRL+ K
Bold
Caps Lock
ALT Make
ALT Break
CTRL Make
CTRL Break
Enter / Ret
(Apple Make)
Tab
Txt: [STX]
Txt: [EXT]
Txt: [EOT]
Txt: [ENQ]
Txt: [ACK]
Txt: [BEL]
Txt: [BS]
Txt: [HT]
Txt: [LF]
3
Copy
4
Bookmark
Center
Find
5
6
7
8
History
Italic
9
HT
10
11
LF
Justify
hyperlink
(Apple Break)
Tab
VT
Txt: [VT]
list,
left align
12
0C
FF
CTRL+ L
Delete
Txt: [FF]
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
CR
CTRL+ M
CTRL+ N
CTRL+ O
CTRL+ P
CTRL+ Q
CTRL+ R
CTRL+ S
CTRL+ T
CTRL+ U
CTRL+ V
CTRL+ W
CTRL+ X
CTRL+ Y
CTRL+ Z
CTRL+ [
CTRL+ \
CTRL+ ]
CTRL+ ^
CTRL+ -
Enter / Ret
Insert
ESC
F11
Txt: [CR]
Txt: [SO]
Txt: [SI]
SO
New
Open
Print
Quit
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
Txt: [DLE]
Txt: [DC1]
Txt: [DC2]
Txt: [DC3]
Txt: [DC4]
Txt: [NAK]
Txt: [SYN]
Txt: [ETB]
Txt: [CAN]
Txt: [EM]
Txt: [SUB]
Txt: [ESC]
Txt: [FS]
Txt: [GS]
Txt: [RS]
Txt: [US]
n/a
Home
PrtScn
Backspace
Back Tab
F12
Save
Paste
F1
F2
F3
F4
SUB
ESC
FS
F5
F6
F7
GS
F8
RS
F9
US
F10
127 7F
NP Enter
⌂
A - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Lower ASCII Reference Table
Note: Windows Code page 1252 and lower ASCII use the same characters.
Printable Characters
DEC HEX Character
DEC HEX Character
DEC HEX Character
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
<SPACE>
!
"
#
$
%
&
'
(
)
*
+
,
-
.
/
0
1
2
3
4
5
6
7
8
9
:
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
@
A
B
C
D
E
F
G
H
I
96
97
98
99
60
61
62
63
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
100 64
101 65
102 66
103 67
104 68
105 69
106 6A
107 6B
108 6C
109 6D
110 6E
111 6F
112 70
113 71
114 72
115 73
116 74
117 75
118 76
119 77
120 78
121 79
122 7A
123 7B
124 7C
125 7D
126 7E
127 7F
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
s
t
u
v
w
x
y
z
{
|
}
~
⌂
;
<
=
>
?
\
]
^
_
A - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Extended ASCII Characters
PS2 Scan
Code
DEC HEX CP 1252
ASCII
Alternate Extended
128 80
129 81
130 82
131 83
€
Ç
ü
é
â
0x48
0x50
0x4B
0x4D
up arrow ↑
down arrow ↓
right arrow →
left arrow ←
Insert
Delete
Home
End
Page Up
Page Down
Right ALT
Right CTRL
Reserved
Reserved
Numeric Keypad Enter
Numeric Keypad /
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
‚
ƒ
132 84
133 85
134 86
135 87
136 88
137 89
138 8A
139 8B
140 8C
141 8D
142 8E
143 8F
144 90
145 91
146 92
147 93
148 94
149 95
150 96
151 97
152 98
153 99
154 9A
155 9B
156 9C
157 9D
158 9E
159 9F
160 A0
161 A1
162 A2
163 A3
164 A4
„
…
†
‡
ˆ
‰
Š
‹
ä
à
å
ç
ê
ë
è
ï
0x52
0x53
0x47
0x4F
0x49
0x51
0x38
0x1D
n/a
Œ
î
ì
n/a
Ž
Ä
Å
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
¢
£
¥
₧
ƒ
á
í
0x1C
0x35
0x3B
0x3C
0x3D
0x3E
0x3F
0x40
0x41
0x42
0x43
0x44
0x57
0x58
0x4E
0x4A
0x37
0x3A
0x45
0x38
0x1D
0x2A
0x36
‘
’
“
”
•
–
—
˜
™
š
›
F11
F12
œ
Numeric Keypad +
Numeric Keypad -
Numeric Keypad *
Caps Lock
Num Lock
Left Alt
Left Ctrl
Left Shift
Right Shift
ž
Ÿ
¡
¢
£
¤
ó
ú
ñ
A - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Extended ASCII Characters (Continued)
PS2 Scan
Code
DEC HEX CP 1252
ASCII
Alternate Extended
165 A5
166 A6
167 A7
168 A8
169 A9
170 AA
171 AB
172 AC
173 AD
174 AE
175 AF
176 B0
177 B1
178 B2
179 B3
180 B4
181 B5
182 B6
183 B7
184 B8
185 B9
186 BA
187 BB
188 BC
189 BD
190 BE
191 BF
192 C0
193 C1
194 C2
195 C3
196 C4
197 C5
198 C6
199 C7
200 C8
201 C9
202 CA
203 CB
¥
¦
§
¨
©
ª
«
¬
Ñ
ª
º
¿
⌐
¬
½
¼
¡
«
»
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
└
┴
┬
├
─
í
Print Screen
Tab
Shift Tab
Enter
n/a
0x0F
0x8F
0x1C
0x01
0x36
0xB6
0x1D
0x9D
Esc
Alt Make
Alt Break
Control Make
Control Break
Alt Sequence with 1 Character 0x36
Ctrl Sequence with 1 Character 0x1D
®
¯
°
±
²
³
´
µ
¶
·
¸
¹
º
»
¼
½
¾
¿
À
Á
Â
Ã
Ä
Å
Æ
Ç
È
É
Ê
Ë
╞
╟
╚
╔
╩
╦
A - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Extended ASCII Characters (Continued)
PS2 Scan
Code
DEC HEX CP 1252
ASCII
Alternate Extended
204 CC
205 CD
206 CE
207 CF
208 D0
209 D1
210 D2
211 D3
212 D4
213 D5
214 D6
215 D7
216 D8
217 D9
218 DA
219 DB
220 DC
221 DD
222 DE
223 DF
224 E0
225 E1
226 E2
227 E3
228 E4
229 E5
230 E6
231 E7
232 E8
233 E9
234 EA
235 EB
236 EC
237 ED
238 EE
239 EF
240 F0
241 F1
242 F2
Ì
Í
Î
Ï
╠
═
╬
╧
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
α
Ð
Ñ
Ò
Ó
Ô
Õ
Ö
×
Ø
Ù
Ú
Û
Ü
Ý
Þ
ß
à
á
â
ã
ä
å
æ
ç
ß
Γ
π
Σ
σ
µ
τ
è
é
ê
ë
ì
í
î
ï
Φ
Θ
Ω
δ
∞
φ
ε
∩
≡
±
ð
ñ
ò
≥
A - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Extended ASCII Characters (Continued)
PS2 Scan
Code
DEC HEX CP 1252
ASCII
Alternate Extended
243 F3
244 F4
245 F5
246 F6
247 F7
248 F8
249 F9
250 FA
251 FB
252 FC
253 FD
254 FE
255 FF
ó
ô
õ
ö
÷
ø
ù
ú
û
ü
ý
≤
⌠
⌡
÷
≈
°
·
·
√
ⁿ
²
þ
ÿ
■
ISO 2022/ISO 646 Character Replacements
Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the bar
code being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, select the code page with
which the bar codes were created. The data characters should then appear
properly.
Code Page Selection
Method/Country
Standard
Keyboard
Country
Honeywell
Code Page
Option
United States
(standard ASCII)
ISO/IEC 646‐IRV
n/a
1
Automatic National
Character
Replacement
ISO/IEC 2022
n/a
2 (default)
Binary Code page
n/a
n/a
3
Default “Automatic National Character replacement” will select the below
Honeywell Code Page options for Code128, Code 39 and Code 93.
A - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
United States
Canada
ISO/IEC 646‐06
ISO /IEC 646‐121
ISO /IEC 646‐122
ISO/IEC 646‐14
ISO/IEC 646‐57
ISO /IEC 646‐04
ISO /IEC 646‐69
ISO/IEC646‐21
ISO /IEC 646‐CH
0
54
18
28
92
7
1
95
96
98
99
87
83
84
86
Canada
Japan
China
Great Britain (UK)
France
3
Germany
Switzerland
4
6
Sweden / Finland
(extended Annex C)
ISO/IEC 646‐11
ISO /IEC 646‐207
ISO/IEC 646‐08
ISO/IEC 646‐60
ISO/IEC 646‐15
ISO/IEC 646‐16
ISO/IEC 646‐17
ISO/IEC 646‐85
2
73
8
82
97
88
94
85
92
90
91
Ireland
Danmark
Norway
Italy
9
5
Portugal
Spain
13
10
51
Spain
A - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
35 36 64 91 92 93 94 96 123 124 125 126
Dec
Hex
23 24 40 5B 5C 5D 5E 60
7B
{
7C
|
ù
ù
|
7D
}
7E
~
û
û
⎯
US
0
54
18
28
92
7
1
#
#
#
#
#
£
£
#
ù
#
#
#
£
£
#
#
#
$
$
$
$
¥
$
$
$
$
¤
$
$
$
$
$
$
$
@
à
[
â
â
[
\
ç
]
ê
ê
]
^
î
`
ô
ô
`
CA
é
é
{
è
è
}
95
96
98
99
87
83
84
86
82
88
94
97
85
92
90
91
à
ç
É
^
^
^
^
^
î
CA
JP
@
@
@
à
¥
\
[
]
`
{
|
}
CN
GB
FR
⎯
[
\
]
`
{
|
}
˜
¨
°
ç
§
Ü
ê
Å
Å
Å
Ú
é
Õ
¿
Ç
µ
`
é
ä
ä
ä
æ
æ
é
à
ã
°
ù
ö
ö
ö
ø
ø
í
è
ü
ü
å
å
å
ú
è
õ
ç
3
§
Ä
é
Ä
Æ
Æ
É
°
Ö
ç
ß
û
ü
˜
¨
DE
CH
SE/FI
DK
NO
IE
4
à
ô
é
`
6
É
Ö
Ø
Ø
Í
Ü
^
^
Á
^
^
^
¿
2
@
@
Ó
§
8
`
9
ó
ù
`
á
ì
73
5
ç
ò
ç
IT
§
Ã
¡
Ç
Ñ
Ñ
°
PT
13
10
51
§
`
ñ
ñ
˜
¨
ES
∙
¡
`
´
ç
ES
ISO / IEC 646 National Character Replacements
A - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Unicode Key Maps
6E
70 71 72 73
74 75 76 77
78 79 7A 7B 7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D
1E 1F 20 21 22 23 24 25 26 27 28 29 2B
4B 50 55
4C 51 56
5A 5F 64 69
5B 60 65
6A
5C 61 66
2C 2E 2F 30 31 32 33 34 35 36 37
39
5D 62 67
6C
4F 54 59
63 68
3D
3A 3B 3C
3E 3F 38 40
104 Key U.S. Style Keyboard
6E
70 71 72 73
74 75 76 77
78 79 7A 7B 7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C
1E 1F 20 21 22 23 24 25 26 27 28 29 2A
4B 50 55
4C 51 56
5A 5F 64 69
5B 60 65
2B
6A
5C 61 66
2C 2D 2E 2F 30 31 32 33 34 35 36 37
39
5D 62 67
6C
4F 54 59
63 68
3D
3A 3B 3C
3E 3F 38 40
105 Key European Style Keyboard
A - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Sample Symbols
Code 39
Codabar
BC321
Code 93
A13579B
Straight 2 of 5 Industrial
123456-9$
123456
Matrix 2 of 5
6543210
GS1 DataBar
(01)00123456789012
Download from Www.Somanuals.com. All Manuals Search And Download.
Honeywell Scanning & Mobility
9680 Old Bailes Road
Fort Mill, SC 29707
HP1300-UG Rev D
1/15
Download from Www.Somanuals.com. All Manuals Search And Download.
|
