Model:
BE-41
Installers Guide
Underwriters
Laboratories Listed
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THISAPPLIANCE. THIS INSTALLERS
GUIDE MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.
WARNING: IF THE INFORMATION
IN THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUS-
ING PROPERTY DAMAGE, PER-
SONAL INJURY, OR DEATH.
WARNING: IMPROPER INSTALLA-
TION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL INFOR-
MATION CONSULT A QUALIFIED IN-
STALLER, SERVICE AGENCY, OR THE
GAS SUPPLIER.
- Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
- What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
1. This appliance may be installed in an af-
termarket, permanently located, manufac-
tured (mobile) home, where not prohibited
by local codes.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
2. This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
- Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
Printed in U.S.A. Copyright 2000,
Please contact your Heat-N-Glo dealer for any
questions or concerns. For the number of your
nearest Heat-N-Glo dealer, please call 952-985-6000.
Heat-N-Glo, a division of Hearth Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.
394-900B 9/00
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Safety and Warning Information ................................................ 2
Service Parts Lists ..................................................................... 4
Section 1: Approvals and Codes ............................................... 6
Approval Listings and Codes ........................................................ 6
Appliance Certification................................................................... 6
Installation Codes.......................................................................... 6
HighAltitude Installations ............................................................... 6
Section 2: Getting Started ......................................................... 7
Introducing the Heat-N-Glo Gas Fireplaces .................................. 7
Pre-installation Preparation ........................................................... 7
Section 3: Installing the Fireplace ............................................ 9
Step 1 Locating the Fireplace ................................................... 9
Step 2 Framing the Fireplace.................................................. 10
Step 3 Installing the Vent System............................................ 12
A. Vent System Approvals........................................... 12
B. Installing Vent Components.................................... 18
C. Vent Termination .................................................... 21
Step 4 Positioning, Leveling, and
Securing the Fireplace................................................. 24
Step 5 The Gas Control Systems ........................................... 24
Step 6 The Gas Supply Line ................................................... 25
Step 7 Gas Pressure Requirements ...................................... 25
Step 8 Wiring the Fireplace .................................................... 26
Step 9 Finishing ...................................................................... 27
Step 10 Installing Trim, Logs, and Ember Material.................... 27
Installing the Trim......................................................... 27
Positioning the Logs .................................................... 27
Placing the Ember Material.......................................... 30
Step 11 Before Lighting the Fireplace ....................................... 30
Step 12 Lighting the Fireplace .................................................. 30
After the Installation ..................................................................... 30
Section 4: Maintaining and Servicing Your Fireplace......... 31
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Parts
BE-41 (NG, LP) Exploded Parts Diagram / Vue éclatée des pièces
10
9
2
1
3
4
8
7
5
6 Log Set Assembly
Part number list on following page.
La liste des numéros de pièce se
trouve à la page suivante.
*
*
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BE-41 Service Parts List / Liste des pièces de rechange
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When
ordering, supply serial and model numbers to ensure correct service parts.
ITEM /
PIÈCE
STANDING PILOT AND DSI IGNITION COMMON PARTS
/ UNE VEILLEUSE ET ALLUMAGE DSI PIÉCES COMMUNES
SERIAL # /N°
DE SÉRIE
PART NUMBER
/ N° DE PIÈCE
Piezo Ignitor / Allumage Piézo
418-513
Burner Orifice NG (#38) / Orifice de brûleur GN (#38)
Burner Orifice LP (#51) / Orifice de brûleur PL (#51)
Surround / Entourent
057-800
079-803
1
2
3
4
4
5
6
7
8
9
520-130
Hood / Hotte
SRV60-143-BK
GLA-750
Glass Door Assembly / Module de Porte en verre
Burner NG / Brûleur GN
389-376A
389-375A
060-361A
LOGS-BE41
100-254A
SRV394-114
SRV394-249
Burner LP / Brûleur PL
Log Grate / Grille de Bûche
Log Set Assembly / Module de Jeu de Bûches
Junction Box / Boîtier de raccordement
Bottom Louver /
Top Louver /
STANDING PILOT IGNITION ONLY / ALLUMAGE UNE VEILLEUSE SEULEMENT
Valve Assembly NG / Module de Valve GN
Valve Assembly LP / Module de Valve PL
Valve NG / Valve GN
10
10
394-005A
394-006A
060-522
Valve LP / Valve PL
060-523
Pilot Assembly NG / Module de veilleuse GN
Pilot Assembly LP / Module de veilleuse PL
Thermocouple / Thermocouple
485-510A
485-511A
446-511
Thermopile / Thermopile
060-512
Pilot Tube / Tube de veilleuse
SRV485-301
ACCESSORIES / ACCESSOIRES
Conversion Kit NG / Module de conversion GN
Conversion Kit LP / Module de conversion PL
Brass Trim Kit /
NGK-BE41
LPK-BE41
PBK-BE41
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Approvals and
Codes
1
High Altitude Installations
Appliance Certification
The Heat-N-Glo fireplace models discussed in this Installers
Guide have been tested to certification standards and listed
by the applicable laboratories.
U.L. Listed gas fireplaces are tested and approved for
elevations from 0 to 2,000 feet in the U.S.A. and from 0 to
4,500 feet in Canada.
When installing this fireplace at an elevation above 2,000
feet (in the United States), it may be necessary to decrease
the input rating by changing the existing burner orifice to a
smaller size. Input should be reduced four percent (4%) for
each 1,000 feet above sea level, unless the heating value of
the gas has been reduced, in which case this general rule
will not apply. To identify the proper orifice size, check with
the local gas utility.
Certification
MODEL: BE-41
LABORATORY: Underwriters Laboratories
TYPE: Direct Vent Gas Fireplace Heater
STANDARD: ANSI Z21.88•CGA2.33
When installing this fireplace at an elevation between 2,000
and 4,500 feet (in Canada), the input rating must be reduced
by ten percent (10%).
Installation Codes
The fireplace installation must conform to local codes. Before
installing the fireplace, consult the local building code
agency to ensure that you are in compliance with all
applicable codes, including permits and inspections.
When installing this fireplace at an elevation above 4,500
feet (in Canada), check with local authorities.
Consult your local gas utility for assistance in determining
the proper orifice for your location.
In the absence of local codes, the fireplace installation must
conform to the National Fuel Gas Code ANSI Z223.1 (in
the United States) or the CAN/CGA-B149 Installation Codes
(in Canada). The appliance must be electrically grounded
in accordance with local codes or, in the absence of local
codes with the National Electric Code ANSI/NFPA No. 70
(in the United States), or to the CSAC22.1 Canadian Electric
Code (in Canada).
These models may be installed in a bedroom or bed-sitting
room in the U.S.A. and Canada.
Heat-N-Glo Quality
Systems registered
by SGS ICS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
2
Introducing the Heat-N-Glo Gas Fireplaces
Heat-N-Glo direct vent gas fireplaces are designed to oper-
ate with all combustion air siphoned from outside of the
building and all exhaust gases expelled to the outside.
The vent system components and trim doors are shipped
in separate packages. The gas logs may be packaged
separately and must be field installed.
The information contained in this Installers Guide, unless
noted otherwise, applies to all models and gas control
systems. Gas fireplace diagrams, including the dimensions,
are shown in this section.
Read all of the instructions before starting the
installation. Follow these instructions carefully during
the installation to ensure maximum safety and benefit.
Failure to follow these instructions will void the
owner’s warranty and may present a fire hazard.
Pre-install Preparation
This gas fireplace and its components are tested and safe
when installed in accordance with this Installers Guide.
Report to your dealer any parts damaged in shipment,
particularly the condition of the glass. Do not install any
unit with damaged, incomplete, or substitute parts.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
When planning a fireplace installation, it’s necessary to
determine:
The Heat-N-Glo Warranty will be voided by, and Heat-N-Glo
disclaims any responsibility for, the following actions:
• Where the unit is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
•
Installation of any damaged fireplace or vent system
component.
•
•
•
•
Modification of the fireplace or direct vent system.
Installation other than as instructed by Heat-N-Glo.
Improper positioning of the gas logs or the glass door.
• Electrical wiring.
• Framing and finishing details.
Installation and/or use of any component part not manu-
factured and approved by Heat-N-Glo, not withstanding
any independent testing laboratory or other party approval
of such component part or accessory.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
If the fireplace is to be installed on carpeting or tile, or on
any combustible material other than wood flooring, the
fireplace should be installed on a metal or wood panel that
extends the full width and depth of the fireplace.
ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE
HAZARD.
28 1/2 [724mm]
14 ¼
[362mm]
21 1/2 [548mm]
8 5/8 [219mm]
VENT COLLARS
11 5/8 [297mm]
8 5/8
[219mm]
VENT
ELECTRICAL
ACCESS
COLLARS
GAS LINE
ACCESS
34 5/8
[879mm]
38
[965mm]
25 ¼
[642mm]
24 5/8
[625mm]
2 1/8
[55mm]
3 ½
[90mm]
36 1/8
[916mm]
10 ¼
[259mm]
41
6 7/8 [174mm]
[1043mm]
TOP STANDOFFS
TOP VENT COLLARS
REAR VENT COLLARS
HOOD
TOP
LOUVER
LOWER
LOUVER
RATING PLATE
AND LABELS
GAS
LINE
ACCESS
ELECTRICAL
ACCESS
GAS
CONTROLS
Figure 1. Diagram of BE-41
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum Clearances
from the Fireplace to Combustible Materials
Inches
mm
Glass Front........................ 36 .................... 914
Floor ................................... 0 ....................... 0
Rear ...................................1/2 ..................... 13
Sides .................................1/2 ..................... 13
Top ................................... 3 1/2 ................... 89
Ceiling* .............................. 31 .................... 787
Installing the Fireplace
3
Step 1.
Locating the Fireplace
The diagram below shows space and clearance require-
ments for locating a fireplace within a room.
* The clearance to the ceiling is measured from the top
of the unit, excluding the standoffs (see Figure 35).
The distance from the unit to combustible construction
is to be measured from the unit outer wrap surface to
the combustible construction, NOT from the screw heads
that secure the unit together.
Minimum Clearances
from the Vent Pipe to Combustible Materials
Inches
mm
Vertical Sections. ............. 1 ................ 25
Horizontal Sections
Top ..................................... 3 ................ 75
Bottom ............................... 1 ................ 25
Sides ................................. 1 ................ 25
At Wall Firestops
Top .................................. 2 1/2 ............ 63.7
Bottom .............................. 1/2 ............... 13
Sides ................................. 1 ................ 25
A
42”
B
22”
C
36”
D
51”
E
72”
Figure 2. Fireplace Dimensions, Locations,
and Space Requirements
For minimum clearances, see the direct vent termination
clearance diagrams on pages 22 and 23 in this manual.
Clearance Requirements
The top, back, and sides of the fireplace are defined by
stand-offs. The minimum clearance to a perpendicular wall
extending past the face of the fireplace is one inch (25 mm).
The back of the fireplace may be recessed 21 1/2 inches
(546 mm) into combustible construction.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2. Framing the Fireplace
Fireplace framing can be built before or after the fireplace is
set in place. Framing should be positioned to accommo-
date wall coverings and fireplace facing material. The dia-
gram below shows framing reference dimensions.
CAUTION: MEASURE FIREPLACE DIMENSIONS AND
VERIFY FRAMING METHODS AND WALL COVERING
DETAILS BEFORE FRAMING.
Shows center of 12” x 12” vent framing
holes for top and rear venting. The center
of the hole is one (1) inch (25.4mm) above
the center of the horizontal vent pipe.
B
C
E
D
A
1/2” CLEARANCE FROM BACK OF FIREPLACE TO COMBUSTIBLE
1/2” CLEARANCE
FROM BOTH SIDES
OF FIREPLACE
A. ............... 42”
B. .........38 1/2”
C. ............... 22”
D. ............... 42”
E. .........25 5/8”
TO COMBUSTIBLE
FRAMING
MEMBER
Framing should be
constructed of 2 X 4
lumber or heavier.
0” CLEARANCE TO
FRAMING MEMBER
0” CLEARANCE
Figure 3. Framing Dimensions
10
Download from Www.Somanuals.com. All Manuals Search And Download.
6 7/16”
(164mm)
8 1/2”
(216mm)
8 1/2”
(216mm)
11 1/16”
(281mm)
5 7/8”
(149mm)
7 3/8”
(187mm)
6 1/2”
5 1/16”
(129mm)
(165mm)
8 5/8”
(220mm)
8 5/8”
(220mm)
11 15/16”
(303mm)
-45D
DV
DV-90D
DV-48D
DV-36D
DV17/24D
DV-12/17D
17-24
(432-610mm)
35 3/4”
(908mm)
47 3/4”
(1.2m)
11 3/4”
(298mm)
8 3/4”
(222mm)
5 3/4”
(146mm)
DV-09D
DV-12D
DV-06D
NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm)
AT EACH JOINT.
Figure 4. D-Series Direct Vent Component Specifications
(5-inch inner pipe / 8 5/8-inch outer pipe)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3. Installing the Vent System
A. Vent System Approvals
Identifying Vent Components
The vent systems installed on this gas fireplace may in-
clude one, two, or three 90° elbow assemblies. The rela-
tionships of vertical rise to horizontal run in vent configura-
tions using 90° elbows MUST BE strictly adhered to. The
rise to run relationships are shown in the venting drawings
and tables. Refer to the diagrams on the next several pages.
These models are approved to use D-series direct vent pipe
components and terminations (see Figures 4 and 5). Ap-
proved vent system components are labeled for identifica-
tion. This pipe is tested and listed as an approved compo-
nent of the fireplace. The pipe is tested to be run inside an
enclosed wall. There is no requirement for inspection open-
ings at each joint within the wall. There is no required pitch
for horizontal vent runs. NO OTHER VENTING SYSTEMS
OR COMPONENTS MAY BE USED.
NOTE: Two 45° elbows may be used in place of one
90° elbow. Rise to run ratios in the vent system must
be followed if 45° elbows are used.
Detailed installation instructions are included with each vent
termination kit and should be used in conjunction with this
Installers Guide.
This model has vent starting collars on both the top and the
back of the unit. Depending upon the installation, decide
which ONE set of starting collars will be used to attach the
vent system. The starting collar sealing cap must remain
on the starting collar NOT used.
The flame and ember appearance may vary based on the type
of fuel burned and the venting configuration used.
VERTICAL
TERMINATION
STORM COLLAR
ROOF FLASHING
HORIZONTAL
TERMINATION
HORIZONTAL PIPE
SUPPORT
PIPE LENGTH
WALL FIRESTOP
Terminations Kits
CEILING
FIRESTOP
WALL BRACKET
90 DEGREE
ELBOW
DVK-01D
DVK-TVCD
DVK-01TRD
Figure 5. Vent System Components and Termination Kits
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HORIZONTALVENTING
Kit No. H Max. Run
DVK-01D
DVK-01TRD 24" (610 mm)
STRAIGHT UP
VERTICAL VENTING
V (FT.)
H
40' MAX. (12.4 M)
90-DEGREE
ELBOWS
45-DEGREE
ELBOW
Figure 6. Straight Up Vertical Venting
NOTE: BE-41 model is tested and approved
to use 45° elbows in corner installations.
However, 90° elbows will result in better per-
formance.
NOTE: On vertical venting configurations where the vertical
component is over 10 feet, you may want to install the
vertical baffle (VERT-BAF) (see Figure 7).
Figure 8. Corner Installation
5” EXHAUST
PIPE
VERTICAL
BAFFLE
CENTER VERTICAL
BAFFLE ON 5”
EXHAUST PIPE
Figure 7. Vertical Baffle
NOTE: Center the vertical baffle over the 5” exhaust pipe.
Fasten in place with self tapping screws.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH ONE (1) 90° ELBOW
V
H
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
2' MAX. (610mm)
4' MAX. (1.22m)
6' MAX. (1.86m)
8' MAX. (2.4m)
V+H=40' MAX. (12.4m)
H = 8' MAX. (2.4m)
NOTE: On vertical venting configurations where
the vertical component is over 10 feet, you may
want to install the vertical baffle (VERT-BAF)
improve flame appearance.
Figure 9. Venting with One 90° Elbow
VENTING WITH ONE (1) 90° ELBOW
V (FT.)
H (FT.)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
5' MAX. (1.52m)
10' MAX. (3.1m)
15' MAX. (4.65m)
20' MAX. (6.2m)
V+H= 40’ MAX. (12.4MM) H = 20' MAX. (6.2m)
H
V
NOTE: For corner installations:A6-inch (152mm)
section of straight pipe may need to be attached to
the fireplace before a 90o elbow, to allow the vent
pipe to clear the top standoffs.
NOTE: If a 90o elbow is first attached to the unit,
the maximum horizontal run is 3-feet (914mm).
Figure 10. Venting with One 90° Elbow
14
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH TWO (2)
90° ELBOWS
V
H
H + H1
1´ MIN. (305 mm)
2´ MIN. (610 mm)
3´ MIN. (914 mm)
4´ MIN. (1.22 m)
2´ MAX. (610 mm)
4´ MAX. (1.22 m)
6´ MAX. (1.86 m)
8´ MAX. (2.48 m)
5´ MAX. (1.52m)
10´ MAX. (3.1m)
15´ MAX. (4.65m)
20´ MAX. (6.2m)
V+H+H1 = 40´ MAX. (12.4 m) H = 8´ MAX. (2.48 m) H+H1 = 20´ MAX. (6.2m)
Figure 11. Venting with Two 90° Elbows
VENTING WITH TWO (2) 90o ELBOWS
V FT.
H + H1 (FT.)
5´ MAX. (1.52m)
10´ MAX. (3.1m)
15´ MAX. (4.65m)
20´ MAX. (6.2m)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
V+H+H1= 40' MAX.(12.4m) H+H1 = 20´ MAX. (6.2m)
V+V1+H= 40' MAX.(12.4m)
Figure 12. Venting with Two 90° Elbows
15
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH THREE (3) 90° ELBOWS
V
H
H + H1
1´MIN. (305mm)
2´MIN. (610mm)
3´MIN. (914mm)
4´MIN. (1.22m)
2´MAX. (610mm)
4´MAX. (1.22m)
6´MAX. (1.86m)
8´MAX. (2.48m)
5´MAX. (1.52m)
10´MAX. (3.1m)
15´MAX. (4.65m)
20´MAX. (6.2m)
V1+V+H+H1 = 40´ MAX.(12.4 m) H = 8´MAX.(2.48 m) H+H1 = 20´MAX.(6.2 m)
V
H
H + H1 + H2
1´MIN. (305mm)
2´MIN. (610mm)
3´MIN. (914mm)
4´MIN. (1.22m)
2´MAX. (610mm)
4´MAX. (1.22m)
6´MAX. (1.86m)
8´MAX. (2.48m)
5´MAX. (1.52m)
10´MAX. (3.1m)
15´MAX. (4.65m)
20´MAX. (6.2m)
1
2
V+H+H +H = 40´ MAX. (12.4 m)
H = 8´ MAX. (2.48 m)
H+H1+H2 = 20´ MAX. (6.2 m)
Figure 13. Venting with three 90° elbows
16
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING WITH THREE (3) 90° ELBOWS
V (FT.)
H (FT.)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
5' MAX. (1.52m)
10' MAX. (3.1m)
15' MAX. (4.65m)
20' MAX. (6.2m)
NOTE: H + H1 = 20' MAX. (6.2m)
V + V1 + H + H1= 40' MAX. (12.4m)
V (FT.)
H + H1 (FT.)
1' MIN. (305mm)
2' MIN. (610mm)
3' MIN. (914mm)
4' MIN. (1.22m)
5' MAX. (1.52m)
10' MAX. (3.1m)
15' MAX. (4.65m)
20' MAX. (6.2m)
H +H1 = 20' MAX. (6.2m)
NOTE: V+V1+H +H1 = 40' MAX. (12.4m)
Figure 14. Venting with three 90° elbows
17
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Attach the First Vent Component to the
Starting Collars
B. Installing Vent Components
After determining which set of starting collars will be used
(top or rear), follow venting instructions accordingly.
To attach the first vent component to the starting collars of
the fireplace:
Venting Out the Rear Vent
Remove the installed rear seal cap from the rear starting
collars by cutting the strap at each end. (see Figure 15).
Follow the vent configuration tables accordingly.
• Apply a 3/8 inch (9.5mm) bead of stove cement around
the 5 inch (127mm) fireplace starting collar.
Remove the insulation from the REAR five inch flue, pull
the heat shield out from outside of the firebox.
• Make sure that the fiberglass rope gasket supplied with
the fireplace seals between the first 8-5/8 inch (219mm)
vent component and the outer fireplace wrap.
WARNING: THE TOP HEAT SHIELD (INSIDE
THE FIREBOX) MUST REMAIN ATTACHED IF
THE VENT SYSTEM IS ATTACHED TO THE
REAR STARTING COLLARS. SEE FIGURE 15.
!
• Lock the vent components into place by sliding the con-
centric pipe sections with four (4) equally spaced interior
beads into the fireplace collar or previously installed com-
ponent end with four (4) equally spaced indented sections.
Venting Out the Top Vent
Remove the two screws in the top vent collar seal cap and
remove the top vent collar seal cap and two pieces of in-
sulation inside the top two starting collars (See Figure 15).
• When the internal beads of each 8-5/8 inch (219mm)
outer pipe line up, rotate the pipe section clockwise about
one-quarter (1/4) turn. The vent pipe is now locked together.
Remove the heat shield from inside the TOP five inch flue
from outside of the firebox.
The glass must be taken off again for positioning the logs
when the unit is finally installed in place and finished around
it. Re-install the glass door. Attach vent system to the top
starting collars.
• The first 90° elbow installed in the vent system of a rear
venting fireplace MUST BE in a vertical position.
WARNING: THE REAR VENT COLLAR SEAL
CAP MUST REMAINATTACHED TO THE REAR
VENT COLLARS IF THE VENT SYSTEM IS AT-
TACHED TO THE TOP STARTING COLLARS.
STARTING
COLLAR
!
WARNING: FAILURE TO REMOVE INSULATION
!
IN THE SET OF COLLARS YOU ARE USING
COULD CAUSE A FIRE.
WARNING:YOU MUST LEAVE THE INSULATION
IN PLACE IN THE SET OF COLLARS YOU ARE
!
STOVE
SEALANT
BEAD
NOT USING.
If your vertical vent component is over 10 feet, you may
want to install the vertical baffle (located in the bag containing
the install manual) to improve flame appearance. Center
the vertical baffle on the 5” flue being used, and with self
tapping screws secure the baffle to the inside of the firebox.
FIRST VENT
COMPONENT
1 INCH
(25.4mm)
Figure 16. Attaching the First Vent Component
to the Starting Collars
Venting Out Top
SEAL
CAP
Venting Out Rear
SEAL
CAP
WARNING: A 3/8 INCH (9.5 MM) BEAD OF
STOVE CEMENT MUST BE PLACED AROUND
!
HEAT
SHIELD
INSULATION
DISCARD BOTH
PIECES and
THE 5 INCH (127 MM) FIREPLACE STARTING COL-
LAR BEFORE ATTACHING THE FIRST VENT COM-
PONENT. FAILURE TO SEAL THIS JOINT MAY
CAUSETHEFIREPLACETO OPERATEIMPROPERLY.
HEAT SHIELD
HEAT
SHIELD
DISCARD
INSULATION
and
HEAT SHIELD
WARNING: ENSURE THAT THE FIBERGLASS
ROPE GASKET SUPPLIED WITH THE
!
FIREPLACE SEALS BETWEEN THE FIRST VENT
COMPONENTAND THE OUTER FIREPLACE WRAP.
Insert screwdriver
or similar object
here to remove cap.
CUT
HERE
If the installation is for a termination cap attached directly
to the fireplace, skip to the sections, Install Firestops and
Vent Termination.
Figure 15
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Continue Adding Vent Components
For Vertical Runs - The vent system must be supported
every eight (8) feet (2.4m) above the fireplace flue outlet by
wall brackets.
• Continue adding vent components, locking each succeed-
ing component into place.
To install support brackets for vertical runs:
• Ensure that each succeeding vent component is secure-
ly fitted and locked into the preceding component in the
vent system.
• Attach wall brackets to the vent pipe and secure the wall
bracket to the framing members with nails or screws.
• 90° elbows may be installed and rotated to any point
around the preceding component’s vertical axis. If an el-
bow does not end up in a locked position with the pre-
ceding component, attach with a minimum of two (2)
sheet metal screws.
WALL BRACKET
WALL STUD
Figure 17. Adding Venting Components
3. Install Support Brackets
8 FT. (2.4m)
FLUE
OUTLET
For Horizontal Runs - The vent system must be supported
every five (5) feet of horizontal run by a horizontal pipe support.
To install support brackets for horizontal runs:
• Place the pipe supports around the vent pipe.
• Nail the pipe supports to the framing members.
1 INCH MIN.
(25.4mm)
Figure 18. Installing Support Brackets
4. Install Firestops
For Horizontal Runs - Firestops are REQUIRED on both
sides of a combustible wall through which the vent passes.
NOTE: Model DVK-01TRD does not need an exterior
firestop on an exterior combustible wall.
To install firestops for horizontal runs that pass through
either interior or exterior walls:
• Cut a 12-inch by 12-inch (305mm X 305mm) hole through
the wall.
NOTE: The center of the hole is one (1) inch (25.4mm)
above the center of the horizontal vent pipe.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
• Position the firestops on both sides of the hole previ-
ously cut and secure the firestops with nails or screws.
For Vertical Runs - One ceiling firestop is REQUIRED at
the hole in each ceiling through which the vent passes.
To install firestops for vertical runs that pass through ceilings:
• The heat shields of the firestops MUST BE placed to-
wards the top of the hole.
• Position a plumb bob directly over the center of the verti-
cal vent component.
• Continue the vent run through the firestops.
• Mark the ceiling to establish the centerpoint of the vent.
• Drill a hole or drive a nail through this centerpoint.
12"
(305mm)
• Check the floor above for any obstructions, such as wir-
ing or plumbing runs.
• Reposition the fireplace and vent system, if necessary,
to accommodate the ceiling joists and/or obstructions.
12"
(305mm)
• Cut an 11-inch X 11-inch (280mm X 280mm) hole through
the ceiling, using the centerpoint previously marked.
1" (25.4 mm)
• Frame the hole with framing lumber the same size as the
ceiling joists.
VENT PIPE
11" (280 mm)
11" (280mm)
Figure 19. 12" x 12" Hole and Vent Pipe
CHIMNEY
HOLE
HEAT SHIELD
TRIM HEAT
EXISTING CEILING
JOISTS
SHIELD IF TOO
LONG, ADD TO
SHIELD IF TOO
SHORT
NEW
FRAMING
MEMBERS
CEILING
EXTERIOR
FIRESTOP
Figure 21. 11" x 11" Hole & New Framing Members
INTERIOR
FIRESTOP
Figure 20. Heat Shield, Interior & Exterior Firestops
20
Download from Www.Somanuals.com. All Manuals Search And Download.
If the area above the ceiling is NOT an attic, position and
secure the ceiling firestop on the ceiling side of the previously
cut and framed hole.
WARNING: THETERMINATIONCAPMUSTBEPO-
SITIONEDSOTHATTHEARROWISPOINTINGUP.
!
For roundcap termination kits:
• Use the exterior pipelock hole on the round flange of the
wall firestop to secure the vent pipe in place.
For trapezoidal cap termination kits:
JOIST
• Using screws secure the cap to the exterior wall through
the flanges in the cap.
WARNING: THE BOTTOM OF THE VENT
TERMINATION CAP MUST BE A MINIMUM
!
CEILING
OF 12 INCHES (305 MM) ABOVE GROUND LEVEL
(GRADE). THE TOP OF THE CAP MUST BE A MIN-
IMUM OF 18 INCHES (457 MM) BELOW COMBUS-
TIBLE MATERIAL, SUCH AS A DECK. THE SIDE
OF THE CAP MUST BE A MINIMUM OF 6 INCHES
(152 MM) AWAY FROM A PARALLEL OUTSIDE
WALL. VENTING TERMINALS SHALL NOT BE RE-
CESSED INTO A WALL OR SIDING. SEE THE FOL-
LOWING DIAGRAM FOR VENT TERMINATION
CLEARANCES.
NAILS (4 REQUIRED)
CEILING FIRESTOP
Figure 22. Ceiling Firestop (Ceiling Side)
If the area above the ceiling IS an attic, position and secure
the firestop on top of the previously framed hole.
NOTE: Keep insulation away from the vent pipe at least
1 inch (25mm).
ROUND CAP TERMINATION
NAILS (4 REQUIRED)
PERFORATION CANNOT BE
INSIDE THE WALL
RAFTER
7 1/2"
(191mm)
MINIMUM
CEILING
CEILING FIRESTOP
Figure 23. Attic Firestop
TRAPEZOID CAP TERMINATION
C. Vent Termination
For Horizontal Terminations - To attach and secure the
termination to the last section of horizontal vent:
• Rotate and interlock the ends as described at the begin-
ning of the Installing Vent Components section.
• The termination kit should pass through the wall firestops
from the exterior of the building.
7 1/4"
(184mm)
• Adjust the termination cap to its final exterior position on
the building.
Figure 24. Round & Trapezoid Termination Caps
21
Download from Www.Somanuals.com. All Manuals Search And Download.
G
v
A
H
D
E
v
L
openable
fixed closed
C
B
v
B
v
v
v
B
F
v
M
I
v
X
B
A
J or K
X
=AIR SUPPLYINLET
=AREA WHERE TERMINAL IS NOT PERMITTED
V
=VENT TERMINAL
I
= 3 ft. (U.S.A.)
A
B
C
= 12" .................... clearances above grade, veran-
da, porch, deck or balcony
6 ft. (Canada)..... clearance to service regu-
lator vent outlet.
= 12" .................... clearances to window or door
that may be opened
J
= 9" (U.S.A.)
12" (Canada) ..... clearance to non-mechan-
ical air supply inlet to
building or the combustion
air inlet to any other ap-
pliance
= 9" (U.S.A.)
12" (Canada) ..... clearance to permanently
closed window.
*D = 18" .................... vertical clearance to ventilated
soffit located above the termi-
K
= 3 ft. (U.S.A.)
6 ft. (Canada) ..... clearance to a mechanical
air supply inlet
nal within a horizontal distance
of 2 feet (60 cm) from the cen-
ter-line of the terminal
**L = 7 ft. ................... clearance above paved
sidewalk or a paved drive-
way located on public
property
*E = 18" .................... clearance to unventilated soffit
F
= 9" ..................... clearance to outside corner
= 6" ...................... clearance to inside corner
***M = 18" .................... clearance under veranda,
porch, deck or balcony
G
H
= 3 ft. (Canada) .... not to be installed above a gas
meter/regulator assembly with-
in 3 feet (90cm) horizontally from
the center-line of the regulator
* 30” minimum for vinyl clad soffits.
** a vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family
dwellings and serves both dwellings.
*** only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor.
NOTE: Local codes or regulations may require different clearances.
Figure 25. Vent Termination Minimum Clearances
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS NECESSARY TO INSTALL THE VINYL
PROTECTOR KIT TO THE TOP OF THE EXTERIOR FIRESTOP (FOR ALL ROUND TERMINATION CAPS).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
To seal the roof hole, and to divert rain and snow from the
vent system:
For Vertical Terminations - To locate the vent and install
the vent sections:
• Locate and mark the vent centerpoint on the underside
of the roof, and drive a nail through the centerpoint.
• Attach a flashing to the roof using nails, and use a non-
hardening mastic around the edges of the flashing base
where it meets the roof.
• Make the outline of the roof hole around the centerpoint
nail.
• Attach a storm collar over the flashing joint to form a
water-tight seal. Place non-hardening mastic around the
joint, between the storm collar and the vertical pipe.
• The size of the roof hole framing dimensions depend on the
pitch of the roof. There MUST BE a 1-inch (25.4mm) clear-
ance from the vertical vent pipe to combustible materials.
• Slide the termination cap over the end of the vent pipe
and rotate the pipe clockwise 1/4 turn.
• Mark the roof hole accordingly.
HORIZONTAL
OVERHANG
• Cover the opening of the installed vent pipes.
• Cut and frame the roof hole.
2 FT.
MIN.
2 FT. MIN.
VERTICAL
WALL
• Use framing lumber the same size as the roof rafters
and install the frame securely. Flashing anchored to the
frame must withstand heavy winds.
LOWEST
DISCHARGE
OPENING
TERMINATION
CAP
• Continue to install concentric vent sections up through
the roof hole (for inside vent installations) or up past the
roof line until you reach the appropriate distance above
the roof (for outside terminations).
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
WARNING: MAJOR U.S. BUILDING CODES
SPECIFY MINIMUM CHIMNEY AND/OR
!
VENT HEIGHTABOVE THE ROOF TOP. THESE MIN-
IMUM HEIGHTS ARE NECESSARY IN THE INTER-
EST OF SAFETY. SEE THE FOLLOWING DIAGRAM
FOR MINIMUM HEIGHTS, PROVIDED THE TERMI-
NATION CAP IS AT LEAST TWO (2) FEET FROM A
VERTICALWALLAND 2-FEET BELOWA HORIZON-
TAL OVERHANG.
Roof Pitch
H (min.) ft.
flat to 6/12
6/12 to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
1.0
1.25
1.5
2.0
2.5
3.25
4.0
5.0
6.0
7.0
7.5
8.0
NOTE: This also pertains to vertical vent systems in-
stalled on the outside of the building.
Figure 26. Minimum Height from Roof to
Lowest Discharge Opening
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4. Positioning, Leveling, and
Securing the Fireplace
Step 5. The Gas Control Systems
WARNING: THIS UNIT IS NOT FOR USE WITH
!
The diagram below shows how to properly position, level,
and secure the fireplace.
SOLID FUEL.
The type of gas control system used with this model is:
Standing Pilot Ignition.
Standing Pilot Ignition System
This system includes millivolt control valve, standing pilot,
thermopile/thermocouple flame sensor, and piezo ignitor.
WARNING: 110-120 VAC MUST NEVER BE
CONNECTED TO A CONTROL VALVE IN A
!
MILLIVOLT SYSTEM.
Figure 27. Proper Positioning,
Leveling and Securing of a Fireplace
• Place the fireplace into position.
• Level the fireplace from side to side and front to back.
• Shim the fireplace with non-combustible material, such
as sheet metal, as necessary.
Figure 28. Gas Controls Systems
• Secure the fireplace to the framing by nailing or screwing.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 6. The Gas Supply Line
Step 7. Gas Pressure Requirements
NOTE: Have the gas supply line installed in accordance
with local building codes by a qualified installer ap-
proved and/or licensed as required by the locality.
Pressure requirements for Heat-N-Glo gas fireplaces
are shown in the table below.
NOTE: Before the first firing of the fireplace, the gas
supply line should be purged of any trapped air.
Pressure
Natural Gas
Propane
Minimum
Inlet Pressure
5.0 inches
w.c.
11.0 inches
w.c.
NOTE: Consult local building codes to properly size
the gas supply line leading to the 1/2 inch (13mm)
hook-up at the unit.
This gas fireplace is designed to accept a 1/2 inch
(13 mm) gas supply line.To install the gas supply line:
• Alisted (and State of Massachussetts approved) 1/2 inch
(13mm) tee-handle manual shut-off valve and a listed
flexible gas connector are connected to the 1/2 inch
(13mm) inlet of the control valve. NOTE: If substituting
for these components, please consult local codes for
compliance.
Maximum Inlet
Gas Pressure
14.0 inches
w.c.
14.0 inches
w.c.
Manifold
Pressure
3.5 inches
w.c.
10.0 inches
w.c.
A one-eighth (1/8) inch (3 mm) N.P.T. plugged tapping is
provided on the inlet and outlet side of the gas control for a
test gauge connection to measure the manifold pressure.
Use a small flat blade screwdriver to crack open the screw
in the center of the tap. Position a rubber hose over the tap
to obtain the pressure reading.
• Locate the gas line access hole in the outer casing of
the fireplace.
• The gas line may be run from either side of the fireplace
provided the hole in the outer wrap does not exceed 2 1/2”
in diameter and it does not penetrate the actual firebox.
The fireplace and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of the system at test pressures in
excess of one-half (1/2) psig (3.5 kPa).
• The gap between the supply piping and gas access hole
can be plugged with non-combustible insulation to pre-
vent cold air infiltration.
The fireplace must be isolated from the gas supply piping
system by closing its individual shut-off valve during any
pressure testing of the gas supply piping system at test
pressures equal to or less than one-half (1/2) psig (3.5 kPa).
• Open the fireplace lower grille, insert the gas supply line
through the gas line hole, and connect it to the shut-off valve.
• When attaching the pipe, support the control so that the
lines are not bent or torn.
• After the gas line installation is complete, use a soap
solution to carefully check all gas connections for leaks.
WARNING: DO NOT USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
!
• At the gas line access hole, use insulation to re-pack
the space around the gas pipe.
• Insert insulation from the outside of the fireplace and
pack the insulation tightly to totally seal between the
pipe and the outer casing.
Use a wrench on
shut-off valve when
tightening gas line.
MANUAL
SHUT-OFF
VALVE
GAS
VALVE
CONTROL
VALVE
FLEX
GAS LINE
CONNECTOR
ACCESS HOLE
Figure 29. Gas Supply Line
25
Download from Www.Somanuals.com. All Manuals Search And Download.
BLACK S2
TH
TP
WHITE T2
RED T1
THERMOPILE
OPTIONAL REMOTE
GAS VALVE
OPTIONAL WALL SWITCH
BLACK S1
Figure 30. Standing Pilot Ignition Wiring Diagram
Step 8. Wiring the Fireplace
Optional Accessories
Optional fan and remote control kits require that 110-120
VAC be wired to the factory installed junction box before
the fireplace is permanently installed.
NOTE: Electrical wiring must be installed by a licensed
electrician.
CAUTION: DISCONNECT REMOTE CONTROLS IF AB-
SENT FOR EXTENDED TIME PERIODS. THIS WILL
PREVENT ACCIDENTAL FIREPLACE OPERATION.
Remote Wall Switch
Position the remote wall switch in the desired position on a
wall. Run a maximum of 25 feet (7.8 m) or less length of 18
A.W.G. minimum wire and connect it to the fireplace ON/
OFF switch pigtails.
For Standing Pilot Ignition Wiring
Appliance Requirements
• This appliance DOES NOT require 110-120 VAC to operate.
WARNING: DO NOT CONNECT 110-120 VAC
TO THE REMOTE WALL SWITCH OR THE
CONTROL VALVE WILL BE DESTROYED.
!
WARNING: DO NOT CONNECT 110-120 VAC
!
TO THE GAS CONTROL VALVE OR THE AP-
PLIANCE WILL MALFUNCTION AND THE
VALVE WILL BE DESTROYED.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNEC-
TION WHEN SERVICING CONTROLS. WIRING ERRORS
CAN CAUSE IMPROPERAND DANGEROUS OPERATION.
VERIFY PROPER OPERATION AFTER SERVICING.
VARIABLE SPEED CONTROL
NOTE: IF ANY OF THE ORIGINAL WIRE
AS SUPPLIED WITH THE APPLIANCE
MUST BE REPLACED, IT MUST BE
REPLACED WITH TYPE 105OC RATED WIRE.
BLK
BLK
JUNCTION BOX
BLK
BLOWER RECEPTACLE
BLK
BLK
BLK
BLK
WHT
WHT
BLK
GROUND
GRN
TEMPERATURE
SENSOR SWITCH
BLOWER
TEMPERATURE
SENSOR SWITCH
JUNCTION BOX
BLK
WHT
110-120 VAC
FAN
SPEED CONTROL
(RHEOSTAT)
Figure 31. Fan Wiring Diagram
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 9. Finishing
FINISH WALL MATERIAL MAY BE DRYWALL
- TOP AND SIDES
Figure 35 shows the minimum vertical and corresponding
maximum horizontal dimensions of fireplace mantels or other
combustible projections above the top front edge of the
fireplace. See Figures 2 and 3 for other fireplace clearances.
0
Only non-combustible materials may be used to cover the
black fireplace front.
WARNING: WHEN FINISHING THE FIREPLACE,
NEVER OBSTRUCT OR MODIFY THE AIR IN-
!
LET/OUTLET GRILLES IN ANY MANNER.
CEILING
0
0
12"
11"
10"
HIGH TEMPERATURE (300O F/149O C MIN.)
TOP & SIDE SEAL JOINT
9"
31”
Figure 33. Sealant Material
8"
7"
6"
12”
11”
5"
10”
Hearth Extensions
4"
2”
9”
3"
8”
7”
A hearth extension may be desirable for aesthetic reasons.
However,ANSI or CAN/CGAtesting standards do not require
hearth extensions for gas fireplace appliances.
2"
1”
6”
5”
4"
3”
1”
TOP FRONT EDGE
OF FIREPLACE
Step 10. Installing Trim, Logs,
and Ember Material
Installing the Trim
Combustible materials may be brought up to the specified
clearances on the side and top front edges of the fireplace,
but MUST NEVER overlap onto the front face. The joints
between the finished wall and the fireplace top and sides
can only be sealed with a 300° F. (149° C) minimum sealant.
Figure 32.
Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles above Fireplace
WARNING: WHEN FINISHING THE FIREPLACE,
NEVER OBSTRUCT OR MODIFY THE AIR INLET/
OUTLET GRILLES IN ANY MANNER.
CAUTION: IF JOINTS BETWEEN THE FINISHED WALLS
AND THE FIREPLACE SURROUND (TOP AND SIDES)
ARE SEALED, A 300° F. MINIMUM SEALANT MATE-
RIAL MUST BE USED. THESE JOINTS ARE NOT RE-
QUIRED TO BE SEALED. ONLY NON-COMBUSTIBLE
MATERIAL (USING 300° F. MINIMUM ADHESIVE, IF
NEEDED) CAN BE APPLIED AS FACING TO THE FIRE-
PLACE SURROUND. SEE THE DIAGRAM BELOW.
!
Install optional marble and brass trim surround kits as
desired. Marble, brass, brick, tile, or other non-combustible
materials can be used to cover up the gap between the
sheet rock and the fireplace.
Do not obstruct or modify the air inlet/outlet grilles. When
overlapping on both sides, leave enough space so that the
bottom grille can be lowered and the trim door removed.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning the Logs
!
BEFORE
FIRING THE UNIT
Follow these steps:
1. Release four glass clips and set the
glass assembly aside.
CAUTION: The log assembly is
fragile. Handle with care.
NOTE: See Step 9 when replacing
the log set in an existing fireplace.
Figure 34
2. Carefully cut the cable tie holding the
log assembly in place and discard the
tie. Do not leave any part of the tie in
the fireplace (see Figure 35).
WARNING: USE WIRE CUT-
TERS. DO NOT ATTEMPT
!
TO CUT THE TIE WITH A
KNIFE.
3. Grasp the log assembly by the
ends. Do NOT grasp the log as-
sembly by the center. Remove the
log assembly from the fireplace and
set aside.
Figure 35
4. Remove the foam pad from the fire-
place and discard. Make sure all piec-
es of the foam are removed. With a
screwdriver bend up the log place-
ment tabs (see Figure 36).
Log Placement Tabs
Figure 36
28
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The grate is located in the lower cav-
ity. Remove the screw holding the
grate in place and discard the screw.
6. Position the grate into the cutout in
the refractory. Hook the grate into po-
sition using the tabs on the bottom
of the grate. Make sure the grate is
pulled forward on the refractory (see
Figure 37).
7. Cut shrink wrap and remove from
Figure 37
around the log assembly.
WARNING: REMOVE ALL
PACKAGING FROM LOGS.
!
8. Install embers. See ember placement
instructions for details.
WARNING: USE DIME SIZE
PIECES ONLY. DO NOT
COVER PORTS.
!
Log Placement Tabs
9. Carefully position the log set in place
into the fireplace. Pull the log set for-
ward until the log set contacts the log
placement tabs. Center the log set in
the firebox side to side (see Figure
38). (Grate removed for viewing.)
Figure 38
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing the Ember Material
Step 11. Before Lighting the Fireplace
Ember material is shipped with this gas fireplace. The bag
labeled Glowing Ember (050-721) is standard glowing ember
material. To place the ember material:
Before lighting the fireplace, be sure to do the following:
Remove all paperwork from underneath the fireplace.
Review safety warnings and cautions
• Pull the four glass latches out of the groove on the glass
frame. Remove glass door from the unit (see Figure 39).
• Read the Safety and Warning Information section at
the beginning of this Installers Guide.
Double-check for gas leaks
• Place dime size pieces of Glowing Ember (050-721)
ember material about 1/2 inch apart near port holes in
burner top. Do NOT press embers into burner ports. Cover
the top of the burner with a single layer of ember mate-
rial. For best performance do NOT place embers on the
ports at the rear of the burner.
• Before lighting the fireplace, double-check the unit for
possible gas leaks.
Double-check vent terminations and front grilles for
obstructions.
• Before lighting the fireplace, double-check the unit for
possible obstructions that could be blocking the vent ter-
minations or the front grilles.
• Save the remaining ember materials for use during fire-
place servicing.
Double-check for faulty components
• Replace the glass door and a front trim door on the unit.
• Any component that is found to be faulty MUST BE re-
placed with an approved component. ampering with the
fireplace components is DANGEROUS and voids all war-
ranties.
• Pull out and latch the glass clips into the groove on the
glass frame.
A small amount of air will be in the gas supply lines. When
first lighting the fireplace, it will take a few minutes for the
lines to purge themselves of this air. Once the purging is
complete, the fireplace will light and will operate normally.
Subsequent lightings of the fireplace will not require this
purging of air from the gas supply lines, unless the gas
valve has been turned to the OFF position, in which
case the air would have to be purged.
NOTE: The fireplace should be run for 8 hours on the initial
start-up. This will help to cure the chemicals used in the
paint and logs.
Figure 39. Glass Assembly
Glass Specifications:
Step 12. Lighting the Fireplace
You’ve reviewed all safety warnings, you’ve checked the
fireplace for gas leaks, you know the vent system is
unobstructed, and you’ve checked for faulty components.
Now you’re ready to light the fireplace.
BE-41:
24 1/2 X 35 1/2 TEMPERED
WARNING: PLEASE REFER TO THE USER’S
MANUAL FORALL CAUTIONS, SAFETY, AND
!
WARNING INFORMATION PERTAINING TO THE
LIGHTING AND OPERATION OF THE FIREPLACE.
After the Installation
LEAVE THIS INSTALLATION MANUAL WITH
THE APPLIANCE FOR FUTURE REFERENCE.
!
Figure 40. Placement of the Ember Material
CAUTION: IT IS STRONGLY RECOMMENDED THAT
TRIM DOORS WITH OPTIONAL MESH SCREENS BE IN-
STALLED ON PROPANE MODELS.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining and Servicing Your Fireplace
4
Fireplace Maintenance
Although the frequency of your fireplace servicing and main-
tenance will depend on use and the type of installation, you
should have a qualified service technician perform an appli-
ance check-up at the beginning of each heating season.
See the table below for specific guidelines regarding each
fireplace maintenance task.
IMPORTANT: TURN OFF THE GAS BEFORE SERVICING
YOUR FIREPLACE.
Replacing old ember material
Frequency: Once annually, during the checkup.
By: Qualified service technician.
Task: Brush away loose ember material near the burner.
Replace old ember material with new dime-size and shape
pieces of Golden Ember (DE-93) and Glowing Ember (050-
721). New ember material should be placed alternately on
top of the burner - a layer of Golden Ember, a layer of
Glowing Ember, and so on. Save the remaining ember
material and repeat this procedure at your next servicing.
For more information, see Placing Ember Material.
MAKE SURE THE FLAMES
ARE STEADY—NOT
LIFTING OR FLOATING.
Figure 41.
Burner Flame Patterns
Cleaning Burner and Controls
Frequency: Once annually.
By: Qualified service technician.
Task: Brush or vacuum the control compartment, fireplace
logs and burner areas surrounding the logs.
Checking Flame Patterns, Flame Height
Frequency: Periodically.
By: Qualified service technician/Home owner.
Task: Make a visual check of your fireplace’s flame patterns.
Make sure the flames are steady - not lifting or floating.
See Figure 41. The flame sensor (DSI) or thermopile/
thermocouple (standing pilot) tips should be covered with
flame. See Figure 28.
Checking Vent System
Frequency: Before initial use and at least annually
thereafter, more frequently if possible.
By: Qualified service technician/Home owner.
Task: Inspect the external vent cap on a regular basis to
ensure that no debris is interfering with the flow of air. Inspect
entire vent system for proper function.
Cleaning Glass Door
Frequency: As necessary
By: Home owner.
Task: Clean as necessary, particularly after adding new ember
(flame colorant) material. Film deposits on the inside of the
glass door should be cleaned off using a household glass
cleaner. NOTE: DO NOT handle or attempt to clean the
door when it is hot and DO NOT use abrasive cleaners.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
|