Generators
GENERATOR SET
6.5 HP - RECOIL START - 2600W/2800W RATED
Model 91523
OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA
1.
2.
Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
Do not operate power tools in explosive atmospheres, such as in the pres-
ence of flammable liquids, gases, or dust. Generators create sparks which
may ignite the dust or fumes.
3.
4.
5.
Keep bystanders, children, and visitors away while operating a generator.
Provide barriers or shields as needed.
ELECTRICAL SAFETY
Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter
plugs. If the tools should electrically malfunction or break down, grounding
provides a low resistance path to carry electricity away from the user.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation eliminates the need for the
three wire grounded power cord and grounded power supply system.
6.
Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
SKU 91523
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
8.
Do not expose Generator to rain or wet conditions. Water entering a
generator will increase the risk of electric shock.
Do not abuse the Power Cord. Keep Power Cords away from heat, oil, sharp
edges, or moving parts. Replace damaged Power Cords immediately. Dam-
aged Power Cords increase the risk of electric shock.
9.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
PERSONAL SAFETY
10.
11.
Stay alert. Watch what you are doing, and use common sense when oper-
ating a generator. Do not use a generator while tired or under the influ-
ence of drugs, alcohol, or medication. A moment of inattention while operat-
ing generators may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
12.
13.
Avoid accidental starting. Make sure the Power Switch is in its“OFF”
position, and disconnect the Spark Plug Wire when not in use.
Remove adjusting keys or wrenches before turning the generator on. A
wrench or a key that is left attached to a rotating part of the generator may result
in personal injury.
14.
15.
Do not overreach. Keep proper footing and balance at all times.
Use safety equipment. Always wear eye protection. Wear ANSI approved
safety impact eye goggles. Dust mask, non-skid safety shoes, hard hat, or
hearing protection must be used for appropriate conditions.
16.
17.
Do not force the generator. Use the Correct generator for your application.
The correct generator will do the job better and safer at the rate for which it is
designed.
Do not use the generator if the Power Switch does not turn it on or off. Any
generator that cannot be controlled with the Power Switch is dangerous and must
be replaced.
SKU 91523
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERATOR USE AND CARE
18.
Make sure the Power Switch is in its“OFF” position and disconnect the
spark plug wire before making any adjustments, changing accessories, or
storing the generator. Such preventive safety measures reduce the risk of
starting the generator accidentally.
19.
20.
21.
Store idle generators out of reach of children and other untrained persons.
Generators are dangerous in the hands of untrained users.
Maintain generators with care. Do not use a damaged generator. Tag dam-
aged generators “Do not use” until repaired.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the generator’s operation. If damaged,
have the generator serviced before using. Many accidents are caused by
poorly maintained generators.
22.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one generator may become hazard-
ous when used on another generator.
SERVICE
23.
24.
25.
Maintain labels and nameplates on the Generator and Engine. These carry
important information. If unreadable or missing, contact Harbor Freight Tools for
a replacement.
Generator service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result in a risk
of injury.
When servicing a generator, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning”section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
SKU 91523
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS
HEART PACEMAKER PRECAUTION
WARNING! People with pacemakers should consult their physician(s)
before using this product. Electromagnetic fields in close proximity to a heart
pacemaker could cause interference to or failure of the pacemaker.
INSTALLATION PRECAUTIONS
1.
Ensure installation meets all applicable safety, and local and national electrical
codes. Have installation performed by a qualified, licensed electrician and
building contractor.
2.
3.
4.
All electrical work, including the earth-ground connection, should be completed
by a licensed electrician.
Any separate fuel storage or Generator supply facility must be built or installed in
full compliance with all relevant local, state, and federal regulations.
It is recommended to use the Generator only in well ventilated out-
door areas. A running gasoline engine will generate Carbon Monox-
ide, a colorless, odorless gas that, if inhaled, can cause serious injury
or death. If the generator is installed indoors, exhaust fumes must be
piped out of the building using leak-free, heat-resistant piping. Pipes and
silencer should not use any flammable materials, nor should they be
installed near the same. Generator exhaust fumes must be within legal
limits and installation must always meet local building codes.
5.
6.
If the generator is installed outdoors, it must be weatherproofed and should be
soundproofed. It should not be run outdoors without protection to the Generator
and wiring conduit.
The Generator weighs 112 lbs. Two or more people should assist when moving
or lifting this product. Never lift the Generator using the engine or alternator lifting
lugs. Connect lifting equipment to the Frame of the Generator.
7.
8.
Before lifting the Generator, ensure the lift rigging and supporting structure are in
good condition, and are rated to lift such a load.
Keep all personnel away from the suspended generator during relocating.
SKU 91523
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
The supporting floor/ground surface should be level, and strong enough to safely
hold the weight of the Generator. If the floor/ground surface is not level, strong
cross members should be placed under the full length of the Generator Frame at
its low side.
10.
11.
For trailer installation, the Generator should be mounted on the center point of the
trailer, over the wheels. The trailer must be capable of supporting the weight of
the Generator and all contents (tools, etc.)
Install sound- and weather-proofing only when it is not raining or snowing to avoid
trapping moisture within the Generator’s area.
FIRE AND EXPLOSION PRECAUTIONS
1.
Gasoline fuel and fumes are flammable, and potentially explosive. Use proper
fuel storage and handling procedures. Always have multiple ABC class fire
extinguishers nearby.
2.
3.
Keep the Generator and surrounding area clean at all times.
When spills of fuel or oil occur, they must be cleaned up immediately. Dispose of
fluids and cleaning materials as per any local, state, or federal codes and regula-
tions. Store oil rags in a covered metal container.
4.
5.
Never store fuel or other flammable materials near the Generator.
Do not smoke, or allow sparks, flames or other sources of ignition around the
Engine and Fuel Tank. Fuel vapors are explosive.
6.
Keep grounded conductive objects, such as tools, away from exposed, live elec-
trical parts and connections to avoid sparking or arcing. These events could
ignite fumes or vapors.
7.
8.
Do not refill the Fuel Tank while the Engine is running or while the Engine is still
hot. Do not operate the Generator with known leaks in the fuel system.
Excessive buildup of unburned fuel gases in the exhaust system can create a
potentially explosive condition. This buildup can occur after repeated failed start
attempts, valve testing, or hot engine shutdown. If this occurs, open exhaust
system drain plugs, if equipped, and allow the gases to dissipate before attempt-
ing to restart the Generator.
9.
Use only engine manufacturer recommended fuel and oil.
SKU 91523
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL PRECAUTIONS
1.
2.
ALWAYS make sure the Power Switch is in its “OFF” position. Disconnect the
spark plug wire, and allow the Engine to completely cool before carrying out
maintenance.
Check for damaged parts. Before using the Generator, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment and binding of moving
parts, any broken parts or mounting fixtures, and any other condition that may
affect proper operation. Any part that is damaged should be properly repaired or
replaced by a qualified technician.
3.
4.
The Generator is designed with guards for protection from moving parts. In any
case, care must still be taken to protect personnel and equipment from other
mechanical hazards when working around the generator.
Do not operate the Generator with safety guards removed. While the Generator
is running, do not attempt to reach around the safety guards for maintenance or
any other reason.
5.
6.
7.
8.
9.
Keep hands, arms, long hair, loose clothing, and jewelry away from moving parts.
Be aware that when engine parts are moving fast they cannot be seen clearly.
Keep access doors on enclosures closed and locked when access is not re-
quired.
When working on or around the Generator always wear protective clothing in-
cluding ANSI approved safety gloves, safety eye goggles, and safety hat.
Do not alter or adjust any part of the Generator that is assembled and supplied
by the manufacturer.
Always follow and complete scheduled Engine and Generator maintenance.
CHEMICAL PRECAUTIONS
1.
2.
Avoid contact with hot fuel, oil, exhaust fumes, and hot solid surfaces.
Avoid body contact with fuels, oils, and lubricants used in the Generator. If
swallowed, seek medical treatment immediately. Do not induce vomiting if fuel is
swallowed. For skin contact, immediately wash with soap and water. For eye
contact, immediately flush eyes with clean water and seek medical attention.
SKU 91523
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
NOISE PRECAUTIONS
1.
1.
Prolonged exposure to noise levels above 85 dBA is hazardous to hearing.
Always wear ANSI approved ear protection when operating or working around
the Generator when it is running.
ELECTRICAL PRECAUTIONS
All connections and conduits from the Generator to the load must only be in-
stalled by trained and licensed electricians, and in compliance with all relevant
local, state, and federal electrical codes and standards, and other regulations
where applicable.
2.
3.
The Generator must be earth-grounded for fixed installations in accordance with
all relevant electrical codes and standards before operation.
®
If an extension cord (not included) is used, make sure to use only UL approved
cords having the correct gauge and length. (See Figure A.)
REQUIRED MINIMUM EXTENSION CORD GAUGE – 120 VOLT
NAMEPLATE
AMPERES
EXTENSION CORD LENGTH
(At Full Load)
0 - 25
Feet
16
16
14
25 - 50
Feet
50 -100
Feet
16
100 – 150
150– 200
Feet
Feet
12
-
0 - 5
5.1 - 8
8.1 - 12
12.1 - 15
15.1 - 20
16
16
14
12
12
10
-
-
-
14
12
10
10
-
-
-
12
10
10
FIGURE A
4.
5.
Do not attempt to connect or disconnect load connections while standing in
water, or on wet or soggy ground.
Do not touch electrically energized parts of the Generator and interconnecting
cables or conductors with any part of the body, or with any non-insulated
conductive object.
6.
7.
Connect the generator only to a load or electrical system (110/120 volt) that is
compatible with the electrical characteristics and rated capacities of the Genera-
tor.
Before servicing equipment powered by the Generator, disconnect the equipment
from its power input.
SKU 91523
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
Keep all electrical equipment clean and dry. Replace any wiring where the insu-
lation is cracked, cut, abraded or otherwise degraded. Replace terminals that
are worn, discolored, or corroded. Keep terminals clean and tight.
9.
Insulate all connections and disconnected wires.
10.
Guard against electric shock. Prevent body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerator enclosures.
INSTALLATION
1.
NOTE: Prior to powering tools and equipment, make sure the Generator’s rated
voltage, wattage, and amperage capacity (115V - 20AMPs) is adequate to supply
all electrical loads that the unit will power. If powering exceeds the Generator’s
capacity, it may be necessary to group one or more of the tools and/or equipment
for connection to a separate Generator.
2.
3.
Electrical and other permits may be required for the installation of emergency
power systems. Investigate the local building and electrical codes before install-
ing this unit. Installation must be completed by licensed contractors.
WARNING! The Generator weighs approximately 112 pounds. Use care
and the proper lifting or hoisting equipment when moving it to the installation
location. Always connect hoist lines to the Frame (41) of the Generator.
GENERAL LOCATION
1.
2.
It is recommended to locate and install the Generator outdoors where cooling air
is readily available.
Install the Generator so that the air inlets and outlets are not blocked by obstruc-
tions such as bushes, trees, or snow drifts. Locating it in the path of heavy winds
or snowdrifts may require the placement of a barrier for protection. The air inlet,
in normal weather conditions, should face the prevailing wind direction.
3.
4.
Install the Generator on a concrete slab or other area where rain drainage or
flood waters can not reach it.
Generator placement should allow four feet of access to all sides for mainte-
nance.
SKU 91523
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
6.
Place the Generator as close as possible to the electrical tools and equipment
being powered to reduce the length of extension cords.
If the Generator in located indoors the Engine exhaust must be ventilated to the
outdoors using leak-proof, heat resistant, flexible, metal, flex tubing.
GENERATOR SUPPORT AND MOUNTING
1.
Mount the Generator on a concrete slab capable of supporting the weight of the
Generator. The slab must extend on all sides beyond the Frame (41) by at least
one foot. Contact a cement contractor for slab specifications if necessary. Attach
the Frame to the concrete slab using 3/8” diameter expansion anchor bolts (not
supplied).
GROUNDING THE GENERATOR
1.
2.
NOTE: It is recommended that only a trained and licensed electrician perform
this procedure.
Connect a #6 AWG grounding wire (not included) from the Ground Connector (8)
on the Generator to a grounding rod (not included) that has been driven at least
24 inches deep into the earth. The grounding rod must be an earth-driven cop-
per or brass rod (electrode) which can adequately ground the Generator.
(See Figure B, next page.)
OPERATING INSTRUCTIONS
NOTE: For additional references to the parts listed in the following pages, refer to the
Assembly Diagrams on pages 19 and 21.
Pre-Start Checks:
1.
2.
Check to make sure the Engine Power Switch (2) is in its “OFF” position.
(See Figure B, next page.)
IMPORTANT! Prior to first using the Generator, the Engine MUST be filled
with approximately 3/4 (0.63) quart of a high quality SAE 10W-30 grade
engine oil. To do so, unscrew and remove the Engine’s Oil Dipstick (65A) located
at the bottom of the Engine Crankcase. Fill the Engine’s Crankcase until the oil
level is level with the upper marked line on the Dipstick. Then, screw the Dip-
stick back into the Oil Fill Hole. (See Figure C, next page.)
SKU 91523
PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE
POWER
SWITCH
(2)
GROUND CONNECTOR
(8)
#6AWG
GROUNDING WIRE
(NOT INCLUDED)
GROUNDING ROD
(NOT INCLUDED)
FIGURE B
FUEL GAUGE (34)
FUELTANK CAP
(33)
FUELTANK
(30)
OIL DIPSTICK
(65A)
FIGURE C
SKU 91523
PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Before the first use, remove the Fuel Tank Cap (33) and fill the Fuel Tank (30) with
nleaded gasoline. Then, replace the Fuel Tank Cap. Thereafter, check the
Engine’s Fuel Gauge (34) for the amount of unleaded gasoline in the Fuel Tank. If
necessary, refill the Fuel Tank with unleaded gasoline; the Generator must be
turned off and cooled down before refilling the fuel tank. (See Figure C.)
To Start The Engine:
1.
2.
Make sure the electrical powered tools/equipment that will be used are not
plugged into the Generator while the Engine is started.
Turn the 120 volt AC Circuit Breaker (5) to its “ON” position. (See Figure D.)
3.
4.
Open the Fuel Valve (40). (See Figure E.)
Close the Choke Lever (21A) to about 1/8” clearance. (See Figure E.)
CIRCUIT BREAKER
(5)
ON
OFF
FIGURE D
CLOSED
OPEN
FUELVALVE (40)
CHOKE LEVER
(21A)
OFF
ON
FIGURE E
SKU 91523
PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Turn the Engine Power Switch (2) to its “ON” position. (See Figure F.)
ENGINE
POWER
SWITCH
(2)
ON
OFF
FIGURE F
6.
7.
Hold the Start Handle (41A) loosely and pull it slowly several times to allow the
gasoline to flow into the Engine’s carburetor. Then hold the Start Handle firmly
and pull the rope hard and fast. Pull the rope all the way out, using two hands if
necessary. If necessary pull the rope several times until the Engine starts.
(See Figure G.)
FUEL TANK (32)
Allow the Engine to run for several seconds. Then, open the Choke Lever (21A)
all the way. (See Figure E.)
120VOLT
DUAL
OUTLETS
(6)
START
HANDLE
(41A)
FIGURE G
SKU 91523
PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering 120 Volt AC Tools And Equipment:
1.
Prior to powering tools and equipment, make sure the Generator’s rated voltage,
and amperage capacity (110/120VAC @ 20 AMPs) is adequate to supply all
electrical loads that the unit will power. If powering exceeds the Generator’s
capacity, it may be necessary to group one or more of the tools and/or equipment
for connection to a separate generator.
CAUTION: THIS GENERATOR IS NOT INTENDED TO POWER SENSITIVE ELECTRONIC
EQUIPMENT (INCLUDING MEDICAL EQUIPMENT)WITHOUTTHE ADDITION OF AN APPROPRIATE
LINE CONDITIONER (SOLD SEPARATELY).
2.
Once the Generator is running, simply connect the Power Cords of 110/120 volt
AC powered tools and equipment into the 110/120 volt AC Dual Outlets (6).
(See Figure G.)
3.
NOTE: The Generator features an AC Non-Fuse Circuit Breaker (5) to protect the
AC circuit in case of an overload. Should an overload occur, the Breaker will
“trip” to its “OFF” position, causing the Generator to automatically shut down. In
this case, refer to Step #1 above in this section. Then, reset the circuitry system
by turning the Circuit Breaker to its “ON” position. Restart the Generator and
continue powering the remaining tools and equipment. (See Figure D.)
4.
5.
When finished using the Generator, turn the Engine Power Switch (2) to its
“OFF” position. Turn the Fuel Valve (40) to its “OFF” position. Then, disconnect
all electrical powered tools and equipment from the Generator’s 110/120 volt AC
Duel Outlets (6). (See Figures E, F, and G.)
After the Engine and Generator have completely cooled, store the Generator in a
safe, clean, dry location (if not already installed in one).
Powering 12 Volt DC Tools And Equipment:
1.
Prior to powering a tool or equipment, make sure the Generator’s rated voltage,
and amperage capacity (12VDC @10 AMPs) is adequate to supply all electrical
loads that the unit will power. If powering exceeds the Generator’s capacity, it may
be necessary to group one or more of the tools and/or equipment for connection to
a separate generator.
2.
Connect the Power Cord of a 12 VDC powered tool or equipment to the DC
Terminals (7). NOTE: Make sure to connect the positive (+) lead of the Power
Cord to the positive (+) Terminal on the Generator, and connect the negative (-)
lead of the Power Cord to the negative (-) Terminal on the Generator.
(See Figure H, next page.)
SKU 91523
PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
If using only a 12 volt DC tool or equipment, turn the 110/120 volt AC Circuit
Breaker (5) to its “OFF” position. (See Figure D.)
4.
5.
Start and run the Engine as previously discussed in this manual.
When finished using the Generator, turn the Engine Power Switch (2) to its
“OFF” position. Turn the Fuel Valve (40) to its “OFF” position. Then, disconnect
the electrical powered tools’ power cord from the Generator’s DC Terminals (7).
(See Figure H.)
6.
7.
After the Engine and Generator have completely cooled, store the Generator in a
safe, clean, dry location (if not already installed in one).
NOTE: The Generator features a 10 AMP DC Fuse (9) to protect the DC circuit in
case of an overload. Should an overload occur the Fuse will burn out, causing
the Generator to automatically shut down. In this case, refer to Step #1 in this
section. Then, reset the circuitry system by replacing the burnt Fuse with a new
10 AMP DC Fuse. Restart the Generator and continue powering the remaining
tool or equipment. (See Figure H.)
POSITIVE (+) DC TERMINAL (7)
10 AMP
DC FUSE
(9)
NEGATIVE (-) DC TERMINAL (7)
FIGURE H
SKU 91523
PAGE 16
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION, CLEANING, AND MAINTENANCE
1.
2.
CAUTION! Always make sure the Engine Power Switch (2) is in its “OFF”
position. Disconnect the spark plug wire from the engine. And allow suffi-
cient time for the Engine and Generator to completely cool before perform-
ing any inspection, maintenance, or cleaning.
Before each use, inspect the general condition of the Generator. Check for
loose screws, misalignment or binding of moving parts, cracked or broken parts,
damaged electrical wiring, and any other condition that may affect its safe opera-
tion. If an Engine problem occurs, always have the Engine immediately checked
out by a qualified service technician before further use.
Do not use damaged equipment.
3.
4.
Before each use, check to make sure the Engine’s oil level and gas level is
adequate. If necessary, fill the Engine’s Crankcase until the oil level is even with
the Oil Fill Hole, and fill the fuel tank.
Before each use, With a soft brush, cloth, or vacuum, remove all debris from the
Generator. Then, use a premium quality, lightweight machine oil to lubricate all
moving parts.
5.
6.
7.
Every 20 hours of use, drain the old Engine oil and replace with approximately
3/4 (0.63) quart of a high quality SAE 10W-30 grade engine oil.
Every 300 hours of use, have a qualified, certified technician perform thorough
maintenance on the Generator and its Engine.
For long term storage, either drain fuel into a suitable container or add a fuel
preservative/stabilizer (not included) to prevent breakdown of the fuel.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS LIST AND ASSEMBLY DIA-
GRAM INTHIS MANUAL AS A REFERENCETOOL ONLY. NEITHERTHE MANUFACTURER OR DISTRIBU-
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KINDTO THE BUYER THAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL
RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR RE-
PLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTSTHERETO.
SKU 91523
PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Part #
Description
Bolt w/Lock Washer (M6 x 12)
Engine Power Switch
Control Panel
Voltmeter
Circuit Breaker
Outlet
DC Terminal
Ground Connector
DC Fuse
Qty.
9
Part #
22
Description
Bolt (M6 x 172)
Bolt (M5x20)
Connection Board
Nut (M5)
Stator
Rotor
Cooling Fan
Heat Insulation Board
Fuel Tank
Qty.
4
1
2
3
4
5
6
7
8
9
1
1
1
1
2
2
1
1
1
4
4
4
1
1
1
4
1
3
1
1
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
4
1
4
1
1
1
1
1
1
1
1
1
2
4
4
4
4
1
1
1
1
10
11
12
13
14
15
16
17
18
19
20
21
Pilot Light
Fuel Filter
Seal Ring
Shock Absorber
Shock Absorber Foot
Lock Washer Nut
Stator Cover
Alternator Back Cover
Capacitor
Bolt (M5 x 16)
Rectifier
Bolt (M5x16)
Fuel Tank cap
Fuel Gauge
Bolt (M6x12)
Lock Washer Bolt (M6x12)
Spacer
Rub Washer
Bush
Fuel Valve
Cable Sheath
Bolt (M8 x 242)
Frame
Switch Box Cover
Engine
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 91523
PAGE 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST A
Part #
1A
2A
3A
4A
5A
6A
7A
8A
Description
Qty.
1
Part #
Description
Starting Case Assy.
Spiral Spring
Starting Wheel
Circlip
Starting Ratchet
Friction Plate Screw
Cover
Starter Pulley
Cooling Fan
Flywheel Magneto
Cylinder Block
Speed Control Lever
Governor Arm
Governor Spring
Governor Support
Bolt (M6 x 15)
Oil Alert Nut
Plug (M10 x 15)
Plug Washer
Oil Alert
Bolt (M6)
Crankshaft
Crankshaft Gear
Oil Dipstick
Oil Dipstick Seal Ring
Gear Casing
Bolt (M8 x 35)
Gear Case Packing
Bearing
Camshaft Assy.
Locating Pin
Qty.
1
Muffler
42A
43A
44A
45A
46A
47A
48A
49A
50A
51A
52A
53A
54A
55A
56A
57A
58A
59A
60A
61A
62A
63A
64A
65A
66A
67A
68A
69A
70A
71A
72A
73A
74A
75A
76A
77A
78A
79A
80A
81A
82A
Cylinder Head Bolt
Cylinder Head Cover Bolt
Cylinder Head Cover
Lock Nut
Adjusting Screw
Rocker Arm
Rocker Arm Bolt
Valve Push Rod Guiding Board
Valve Push Rod
Cylinder Head
Carburetor Shield
Carburetor Packing I
Carburetor Assembly
Air Cleaner Case
Air Cleaner Seal
Bolt (M6)
Air Cleaner Cover
Air Cleaner Element
Air Cleaner Separator
Choke Lever
Carburetor Packing II
Stud Bolt (M6 x 109)
Intake Valve
4
4
1
2
2
3
2
1
2
1
1
1
1
1
1
4
1
1
1
1
1
2
1
1
1
2
1
2
2
2
2
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
2
2
1
2
1
1
2
2
1
6
2
2
1
4
2
2
1
1
1
1
1
1
1
2
9A
10A
11A
12A
13A
14A
15A
16A
17A
18A
19A
20A
21A
22A
23A
24A
25A
26A
27A
28A
29A
30A
31A
32A
33A
34A
35A
36A
37A
38A
39A
40A
41A
Exhaust Valve
Cylinder Head Gasket
Exhaust Pipe Stud
Spark Plug
Valve Guide
Valve Spring
Rocker Shaft Circlip
Anti-Wear Valve Stem Protector
Cylinder Head Cover Packing
Governor Spring
Bolt
High Tension Line
Ignition Coil
Nut (Special 14mm)
Starter Ratchet Spring
Start Rope
Oil Seal
Connecting Rod Bolt
Connecting Rod Cap
Connecting Rod
Piston
Compression Ring I
Compression Ring II
Oil Scraper Ring
Piston Pin
Start Handle
Piston Pin Circlip
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 91523
PAGE 20
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM A
SKU 91523
PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
|